Instruction Sheet CHAMP* Right-Angle-Mount 408-7672 and Vertical-Mount Printed (was IS 7672) Circuit (PC) Board Connectors Right-Angle-Mount Connector Shielded 09 AUG 06 Vertical-Mount Connector Rev A Shielded Contact Tines (Typ) Unshielded Unshielded 2.16 [.085] (Typ) RECEPTACLE CONNECTORS CONNECTOR RIGHT-ANGLE POSITIONS 14 RIGHT-ANGLE VERTICAL UNSHIELDED SHIELDED UNSHIELDED SHIELDED 552738 --- 552212 --- 552739 552209 552224 554501 552741 552221 552235 554145, 554400 552743 552232 552118 554216, 554217 552726 552116 552246 --- 552745 552243 { 24 PLUG CONNECTORS VERTICAL 552740, 552791 UNSHIELDED 553119, 553121, 553811, 554923, 555139 553448, 553815, 36 552742, 555493 554907, 555119, 555233, 555520 50 64 552725, 554663, 553813, 554901, 554841, 555492 555057, 555149 552744 --- NOTE: Right-Angle-Mount Plug and Receptacle Connectors are available in standard pin orientation and reverse pin orientation. { For IEEE 488-1975 applications. Figure 1 1. INTRODUCTION (Figure 1) 2. DESCRIPTION This instruction sheet covers the CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors (unshielded and shielded). These instructions include connector description and connector mounting procedures. Read this and all referenced material thoroughly before installing any connectors. NOTE Dimensions are in millimeters [with inch equivalents in brackets]. Figures are for identification only and are not drawn to scale. Reasons for reissue are provided in Section 5, REVISION SUMMARY. E 2006 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved Tyco is a trademark. Plug and receptacle connectors consist of polarized housings which are preloaded with solder-tine contacts on 2.16 mm [.085 in.] centers. They are available with 14, 24, 36, 50, and 64 contact positions that are arranged in two opposing rows. Vertical-mount connectors feature straight contact tines with 4.29 mm [.169 in.] between rows. The connectors may be installed on 1.57-3.18 mm [.062-.125 in.] thick pc boards. Shielded connectors have 2.54 and 5.08 mm [.100 and .200 in.] tail lengths. The 2.54 mm [.100 in.] tail can only be used on 1.57 mm [.062 in.] thick pc boards. TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, *Trademark Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 3 LOC B 408-7672 CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors Right-angle-mount connectors are available for standard or reverse pin orientation on the pc board, refer to Figure 3 for application pin location. The contacts feature 90 bent contact tines with 4.29 mm [.169 in.] between rows. The connectors may be installed on 1.57-3.18 mm [.062-.125 in.] thick pc boards. Shielded connectors have a 3.99 mm [.157 in.] tail length, which is not suitable for 3.18 mm [.125 in.] thick pc boards. Standard Orientation Reverse Orientation Pin No. 1 Pin No. 1 Pin No. 1 Hole for Reverse Orientation Shielded CHAMP Connectors afford excellent protection from Electromagnetic Interference (EMI) or electrostatic discharge to sensitive circuitry. These connectors are intermateable with existing connectors for cable-to-pc board applications. Refer to Instruction Sheet 7564 for cable connector information. All connectors have mounting flanges for attachment to the pc board and/or mating connector. Refer to instruction sheet 408-3160 for hardware information. Pin No. 1 Hole for Standard Orientation Right-Angle-Mount Connector Rotate 3. CONNECTOR MOUNTING PROCEDURES CAUTION NOTE BEFORE attempting to install connector on the pc board, CLOSELY inspect for deformed broken First Row Started contacts. Into Holes PC Board Care must be used when installing these connectors; otherwise, the contact tines may be Vertical-Mount Connector Rotate damaged. Also, correct orientation of the connector pin pattern with the pc board pattern should be checked. The following procedures are recommended for shielded and unshielded connectors: First Row Started 1. Hold connector at a slight angle to the pc board and start one row of contacts into the contact holes. See Figure 2. Into Holes PC Board Figure 2 2. Rotate the connector until contact tines are aligned with opposite row of holes on pc board. 4. Inspect contacts to make certain none have been deformed. All contact tines MUST extend through the pc board a minimum of 0.81 mm [.032 in.] for a good fillet. 3. Make sure contact tines have started entrance into the holes, then push connector straight down until the standoffs bottom on the pc board. 5. Secure connector to pc board with CHAMP connector approved hardware, or the appropriate hardware kit selected for mating connectors. 2 of 3 Rev A CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors 6. Solder contact tines to the pc board using high density wave solderable applications, or a standard reflow soldering technique. 4. PANEL MOUNTING 408-7672 Screw Lock Kit Front of Panel Either the plug or receptacle right-angle-mount or vertical-mount connector may be REAR panel mounted (see Figure 3). NOTE Panel thickness affects connector mating and hardware fastening. Consult reference documents or Tyco Electronics Engineering for Screw application requirements. 5. REVISION SUMMARY S Updated document to corporate requirements S General update to format S Deleted obsolete part numbers from table in Figure 1 Rev A Standoff Figure 3 3 of 3