Instruction Sheet
CHAMP* Right-Angle-Mount
and Vertical-Mount Printed 408-7672
(was IS 7672)
LOC B
1
of 3
E
2006 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
Tyco is a trademark. *Trademark
Other products, logos, and company names used are the property of their respective owners.
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
09 AUG 06 Rev A
Circuit (PC) Board Connectors
Shielded
Unshielded
Right-Angle-Mount
Connector Vertical-Mount
Connector
Shielded
Unshielded
Contact Tines
(Typ)
2.16 [.085] (Typ)
CONNECTOR
RECEPTACLE CONNECTORS PLUG CONNECTORS
CONNECTOR
POSITIONS
RIGHT-ANGLE VERTICAL RIGHT-ANGLE VERTICAL
POSITIONS
UNSHIELDED SHIELDED UNSHIELDED SHIELDED UNSHIELDED
14 552738 --- 552212 --- 552739 552209
24 552740, 552791
{
553119, 553121,
553811, 554923,
555139 552224 554501 552741 552221
36 552742, 555493 553448, 553815,
554907, 555119,
555233, 555520 552235 554145, 554400 552743 552232
50 552725, 554663,
554841, 555492 553813, 554901,
555057, 555149 552118 554216, 554217 552726 552116
64 552744 --- 552246 --- 552745 552243
NOTE:
Right-Angle-Mount Plug and Receptacle Connectors are available in standard pin orientation and reverse pin orientation.
{
For IEEE 488-1975 applications.
Figure 1
1. INTRODUCTION
(Figure 1)
This instruction sheet covers the CHAMP
Right–Angle–Mount and Vertical–Mount PC Board
Connectors (unshielded and shielded).
These instructions include connector description and
connector mounting procedures. Read this and all
referenced material thoroughly before installing any
connectors.
Dimensions are in millimeters [with inch
equivalents in brackets]. Figures are for
identification only and are not drawn to scale.
Reasons for reissue are provided in Section 5,
REVISION SUMMARY.
2. DESCRIPTION
Plug and receptacle connectors consist of polarized
housings which are preloaded with solder–tine
contacts on 2.16 mm [.085 in.] centers. They are
available with 14, 24, 36, 50, and 64 contact positions
that are arranged in two opposing rows.
Vertical–mount connectors feature straight contact
tines with 4.29 mm [.169 in.] between rows. The
connectors may be installed on 1.57–3.18 mm
[.062–.125 in.] thick pc boards. Shielded connectors
have 2.54 and 5.08 mm [.100 and .200 in.] tail
lengths. The 2.54 mm [.100 in.] tail can only be used
on 1.57 mm [.062 in.] thick pc boards.
NOTE
408-7672
CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors
Rev
A2
of 3
Right–angle–mount connectors are available for
standard or reverse pin orientation on the pc board,
refer to Figure 3 for application pin location. The
contacts feature 90° bent contact tines with 4.29 mm
[.169 in.] between rows. The connectors may be
installed on 1.57–3.18 mm [.062–.125 in.] thick pc
boards. Shielded connectors have a 3.99 mm
[.157 in.] tail length, which is not suitable for 3.18 mm
[.125 in.] thick pc boards.
Shielded CHAMP Connectors afford excellent
protection from Electromagnetic Interference (EMI) or
electrostatic discharge to sensitive circuitry.
These connectors are intermateable with existing
connectors for cable–to–pc board applications. Refer
to Instruction Sheet 7564 for cable connector
information. All connectors have mounting flanges for
attachment to the pc board and/or mating connector.
Refer to instruction sheet 408–3160 for hardware
information.
3. CONNECTOR MOUNTING PROCEDURES
BEFORE attempting to install connector on the
pc board, CLOSELY inspect for deformed broken
contacts.
Care must be used when installing these
connectors; otherwise, the contact tines may be
damaged. Also, correct orientation of the
connector pin pattern with the pc board pattern
should be checked.
The following procedures are recommended for
shielded and unshielded connectors:
1. Hold connector at a slight angle to the pc board
and start one row of contacts into the contact
holes. See Figure 2.
2. Rotate the connector until contact tines are
aligned with opposite row of holes on pc board.
3. Make sure contact tines have started entrance
into the holes, then push connector straight down
until the standoffs bottom on the pc board.
Figure 2
Pin No. 1
Reverse Orientation
Pin No. 1
Standard Orientation
Pin No. 1 Hole for
Reverse Orientation
Pin No. 1 Hole for
Standard Orientation
Rotate
Rotate
Right-Angle-Mount
Connector
Vertical-Mount
Connector
First Row Started
Into Holes PC Board
PC Board
First Row Started
Into Holes
4. Inspect contacts to make certain none have
been deformed. All contact tines MUST extend
through the pc board a minimum of 0.81 mm
[.032 in.] for a good fillet.
5. Secure connector to pc board with CHAMP
connector approved hardware, or the appropriate
hardware kit selected for mating connectors.
CAUTION
NOTE
408-7672
CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors
3
of 3Rev
A
6. Solder contact tines to the pc board using high
density wave solderable applications, or a standard
reflow soldering technique.
4. PANEL MOUNTING
Either the plug or receptacle right–angle–mount or
vertical–mount connector may be REAR panel
mounted (see Figure 3).
Panel thickness affects connector mating and
hardware fastening. Consult reference
documents or Tyco Electronics Engineering for
application requirements.
5. REVISION SUMMARY
S
Updated document to corporate requirements
S
General update to format
S
Deleted obsolete part numbers from table in
Figure 1
Figure 3
Front of Panel
Screw
Standoff
Screw Lock Kit
NOTE
