The following products presented in this data sheet are being withdrawn:
B39461B3578U310
Date of withdrawal: 22−DEC−04
Deadline for last orders: 31−MAR−05
Last shipments: 30−JUN−05
For further information please contact your nearest EPCOS sales office, which will also support
you in selecting a suitable substitute. The addresses of the sales offices are given on the Internet
at www.epcos.com/sales.
1
SAW Components
Data Sheet B3578
2Nov 28, 2002
SAW Components (B3578)
463,70 MHzLow-loss Filter
Data Sheet
Features
RF low-loss filter for remote control receivers
Package for Surface Mounted Technology
(SMT)
Balanced and unbalanced operation possible
Terminals
Ni, gold plated
Pin configuration
1 Input Ground
2 Input
5 Output
6 Output Ground
4,8 Case - Ground
3,7 to be grounded
Electrostactic Sensitive Device (ESD)
Type Ordering code Marking Packing
according to
B3578 B39461-B3578-U310 C61157-A7-A56 F61074-V8070-Z000
Maximum ratings
Operable temperature range
T
A–40/+95 ˚C
Storage temperature range
T
stg –40/+95 ˚C
DC voltage
V
DC 0V
Source power
P
S
10 dBm source impedance 50
typ. dimensions in mm, approx. weight 0,1 g
Ceramic package QCC8C
3Nov 28, 2002
SAW Components (B3578)
463,70 MHzLow-loss Filter
Data Sheet
Characteristics
Reference temperature:
T
A= -40 ... 95 ˚C
Terminating source impedance:
Z
S= 50 and matching network
Terminating load impedance:
Z
L= 50 and matching network
1)Temperature dependence of
f
C
:
f
C
(
T
A) =
f
C
(
T
0
) (1 +
TC
f(
T
A
T
0
)2)
min. typ. max.
Center frequency
f
C
463,70 MHz
(center frequency between 3 dB points)
Minimum insertion attenuation αmin
463,57 ... 463,83 MHz 1,9 3,2 dB
Pass band (relative to αmin)
463,57 ... 463,83 MHz 0,8 2,0 dB
463,52 ... 463,88 MHz 1,0 3,0 dB
Relative attenuation (relative to αmin)αrel
10,00 ... 443,00 MHz 48 53 dB
443,00 ... 453,50 MHz 44 49 dB
453,50 ... 461,70 MHz 30 35 dB
461,70 ... 462,70 MHz 12 15 dB
464,70 ... 471,70 MHz 15 18 dB
471,70 ... 550,00 MHz 40 45 dB
550,00 ...1000,00 MHz 45 50 dB
Impedance for pass band matching
Input:
Z
IN =
R
IN ||
C
IN 168 ||2,60 || pF
Output:
Z
OUT =
R
OUT ||
C
OUT 164 ||2,80 || pF
Temperature coefficient of frequency 1)
TC
f –0,03 ppm/K2
Frequency inversion point
T
0
5—25°C
4Nov 28, 2002
SAW Components (B3578)
463,70 MHzLow-loss Filter
Data Sheet
Matching network to 50 (element values depend on pcb layout and equivalent circuit)
Cp1 = 1,2 pF
Ls2 = 27 nH
Ls3 = 27 nH
Cp4 = 1,2 pF
Minimising the crosstalk
For a good ultimate rejection a low crosstalk is necessary. Low crosstalk can be realised with
a good RF layout. The major crosstalk mechanism is caused by the “ground-loop” problem.
Grounding loops are created if input-and output transducer GND are connected on the top-side
of the PCB and fed to the system grounding plane by a common via hole. To avoid the common
ground path, the ground pin of the input- and output transducer are fed to the system ground
plane (bottom PCB plane) by their own via hole. The transducers’ grounding pins should be
isolated from the upper grounding plane.
A common GND inductivity of 0.5nH degrades the ultimate rejection (crosstalk) by 20dB.
The optimised PCB layout, including matching network for transformation to 50 Ohm, is shown
here. In this PCB layout the grounding loops are minimised to realise good ultimate rejection.
Optimised PCB layout for SAW filters in QCC8C package, pinning 2,5 (top side, scale 1:1)
The bottom side is a copper plane (system ground area). The input and output grounding pins
are isolated and connected to the common ground by separated via holes.
For good contact of the upper grounding area with the lower side it is necessary to place
enough via holes.
5Nov 28, 2002
SAW Components (B3578)
463,70 MHzLow-loss Filter
Data Sheet
Normalized frequency response
Normalized frequency response (wideband)
6Nov 28, 2002
SAW Components (B3578)
463,70 MHzLow-loss Filter
Data Sheet
Published by EPCOS AG
Surface Acoustic Wave Components Division, SAW CE AE PD
P.O. Box 80 17 09, D-81617 München
EPCOS AG 2001. All Rights Reserved.
A
s far as patents or other rights of third parties are concerned, liability is only assumed for compo-
nents per se, not for applications, processes and circuits implemented within components or
assemblies.
T
he information describes the type of component and shall not be considered as assured
characteristics.
T
erms of delivery and rights to change design reserved.
For questions on technology, prices and delivery please contact the sales offices of EPCOS AG or
t
he international representatives.
Due to technical requirements components may contain dangerous substances. For information on
t
he type in question please also contact one of our sales offices.