MC10103 Quad 2-Input OR Gate The MC10103 is a quad 2-input OR gate. The MC10103 provides one gate with OR/NOR outputs. * PD = 25 mW typ/gate (No Load) * tpd = 2.0 ns typ * tr, tf = 2.0 ns typ (20%-80%) http://onsemi.com LOGIC DIAGRAM MARKING DIAGRAMS 4 2 5 6 16 CDIP-16 L SUFFIX CASE 620 3 7 12 1 15 9 13 10 16 PDIP-16 P SUFFIX CASE 648 14 11 MC10103L AWLYYWW VCC1 = PIN 1 VCC2 = PIN 16 VEE = PIN 8 MC10103P AWLYYWW 1 1 PLCC-20 FN SUFFIX CASE 775 DIP PIN ASSIGNMENT VCC1 1 16 VCC2 AOUT 2 15 COUT BOUT 3 14 DOUT AIN 4 13 CIN AIN 5 12 CIN BIN 6 11 DIN BIN 7 10 DIN VEE 8 9 COUT A WL YY WW 10103 AWLYYWW = Assembly Location = Wafer Lot = Year = Work Week ORDERING INFORMATION Device Package Shipping MC10103L CDIP-16 25 Units / Rail MC10103P PDIP-16 25 Units / Rail MC10103FN PLCC-20 46 Units / Rail Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 18 of the ON Semiconductor MECL Data Book (DL122/D). Semiconductor Components Industries, LLC, 2002 January, 2002 - Rev. 7 1 Publication Order Number: MC10103/D MC10103 ELECTRICAL CHARACTERISTICS Test Limits Characteristic Symbol Pin Under Test Power Supply Drain Current IE 8 29 IinH 4* 390 Input Current -30C Min +25C Max Min +85C Typ Max Max Unit 21 26 29 mAdc 245 245 Adc 0.5 Min Adc IinL 4* 0.5 Output Voltage Logic 1 VOH 2 9 -1.060 -1.060 -0.890 -0.890 -0.960 -0.960 -0.810 -0.810 -0.890 -0.890 0.3 -0.700 -0.700 Vdc Output Voltage Logic 0 VOL 2 9 -1.890 -1.890 -1.675 -1.675 -1.850 -1.850 -1.650 -1.650 -1.825 -1.825 -1.615 -1.615 Vdc Threshold Voltage Logic 1 VOHA 2 9 -1.080 -1.080 Threshold Voltage Logic 0 VOLA 2 9 t4+2+ t12+9- 2 9 1.0 1.0 3.1 3.1 1.0 1.0 2.0 2.0 2.9 2.9 1.0 1.0 3.3 3.3 -0.980 -0.980 -0.910 -0.910 -1.655 -1.655 -1.630 -1.630 Vdc -1.595 -1.595 Switching Times (50 Load) Propagation Delay Vdc ns Rise Time (20 to 80%) t2+ 2 1.1 3.6 1.1 2.0 3.3 1.1 3.7 Fall Time (20 to 80%) t2- 2 1.1 3.6 1.1 2.0 3.3 1.1 3.7 * Individually test each input applying VIH or VIL to input under test. http://onsemi.com 2 MC10103 ELECTRICAL CHARACTERISTICS (continued) TEST VOLTAGE VALUES (Volts) Characteristic Power Supply Drain Current Input Current @ Test Temperature VIHmax VILmin VIHAmin VILAmax VEE -30C -0.890 -1.890 -1.205 -1.500 -5.2 +25C -0.810 -1.850 -1.105 -1.475 -5.2 +85C -0.700 -1.825 -1.035 -1.440 -5.2 Symbol Pin Under Test IE 8 IinH 4* IinL 4* Output Voltage Logic 1 VOH 2 9 Output Voltage Logic 0 VOL 2 9 Threshold Voltage Threshold Voltage Switching Times Logic 1 Logic 0 VOHA VOLA TEST VOLTAGE APPLIED TO PINS LISTED BELOW VIHmax VILmin (VCC) Gnd 8 1, 16 8 1, 16 8 1, 16 8 8 1, 16 1, 16 8 8 1, 16 1, 16 8 8 1, 16 1, 16 4, 5 8 8 1, 16 1, 16 Pulse In Pulse Out -3.2 V +2.0 V VILAmax 4* 4* 4.5 12, 13 2 9 4, 5 12, 13 2 9 12, 13 (50 Load) Propagation Delay VEE VIHAmin t4+2+ t12+9- 2 9 4 12 2 9 8 8 1, 16 1, 16 Rise Time (20 to 80%) t2+ 2 4 2 8 1, 16 Fall Time (20 to 80%) t2- 2 4 2 8 1, 16 * Individually test each input applying V IH or VIL to input under test. Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50-ohm resistor to -2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner. http://onsemi.com 3 MC10103 PACKAGE DIMENSIONS PLCC-20 FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C 0.007 (0.180) B Y BRK -N- M T L-M 0.007 (0.180) U M N S T L-M S G1 0.010 (0.250) S N S D -L- -M- Z W 20 D 1 X V S T L-M S N S VIEW D-D A 0.007 (0.180) M T L-M S N S R 0.007 (0.180) M T L-M S N S Z 0.007 (0.180) H M T L-M S N S K1 K C E F 0.004 (0.100) G J -T- VIEW S G1 0.010 (0.250) S T L-M S N S 0.007 (0.180) M T L-M S VIEW S SEATING PLANE NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). http://onsemi.com 4 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --0.025 --0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --0.020 2 10 0.310 0.330 0.040 --- MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --0.64 --8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --0.50 2 10 7.88 8.38 1.02 --- N S MC10103 PACKAGE DIMENSIONS -A- 16 9 1 8 -B- CDIP-16 L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE T C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. L DIM A B C D E F G H K L M N -T- K N SEATING PLANE M E F J G D 16 PL 0.25 (0.010) 16 PL 0.25 (0.010) M T A T B M S PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R -A- 16 9 1 8 B F C L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M S T A M http://onsemi.com 5 INCHES MIN MAX 0.750 0.785 0.240 0.295 --0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0 15 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0 15 0.51 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 MC10103 Notes http://onsemi.com 6 MC10103 Notes http://onsemi.com 7 MC10103 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 MC10103/D