INTEGRATED CIRCUITS DATA SHEET 74LVC32244A; 74LVCH32244A 32-bit buffer/line driver; 5 V input/output tolerant; 3-state Product specification File under Integrated Circuits, IC24 1999 Aug 31 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A FEATURES DESCRIPTION * 5 V tolerant inputs/outputs for interfacing with 5 V logic The 74LVC(H)32244A is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. Inputs can be driven from either 3.3 or 5 V devices. In 3-state operation, outputs can handle 5 V. These features allow the use of these devices in a mixed 3.3 and 5 V environment. * Wide supply voltage range of 1.2 to 3.6 V * CMOS low power consumption * MULTIBYTE flow-trough standard pin-out architecture * Low inductance multiple power and ground pins for minimum noise and ground bounce The 74LVC(H)32244A is a 32-bit non-inverting buffer/line driver with 3-state outputs. The 3-state outputs are controlled by the output enable inputs 1OE and 2OE. A HIGH on input nOE causes the outputs to assume a high-impedance OFF-state. * Direct interface with TTL levels * Bus hold on data inputs (74LVCH32244A only) * Typical output ground bounce voltage: VOLP <0.8 V at VCC = 3.3 V; Tamb = 25 C To ensure the high-impedance state during power-up or power-down, input nOE should be tied to VCC through a pull-up resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. * Typical output VOH undershoot voltage: VOHV >2 V at VCC = 3.3 V; Tamb = 25 C * Power-off disabled outputs, permitting live insertion * Plastic fine-pitch ball grid array package. The 74LVCH32244A bus hold data input circuit eliminates the need for external pull-up resistors to hold unused or floating data inputs at a valid logic level (see Fig.3). QUICK REFERENCE DATA Ground = 0 V; Tamb = 25 C; tr = tf 2.5 ns. SYMBOL PARAMETER tPHL/tPLH propagation delay nAn to nYn CI input capacitance CPD power dissipation capacitance per buffer CONDITIONS 3.0 5.0 pF VI = GND to VCC; note 1 25 pF 1. CPD is used to determine the dynamic power dissipation (PD in W). fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in Volts; (CL x VCC2 x fo) = sum of the outputs. 1999 Aug 31 2 UNIT CL = 50 pF; VCC = 3.3 V Note PD = CPD x VCC2 x fi + (CL x VCC2 x fo) where: TYPICAL ns Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A FUNCTION TABLE See note 1. INPUT OUTPUT nOE nAn nYn L L L L H H H X Z Note 1. H = HIGH voltage level; L = LOW voltage level; X = don't care; Z = high-impedance OFF-state. ORDERING INFORMATION PACKAGES TYPE NUMBER 74LVC32244AEC TEMPERATURE RANGE PINS -40 to +85 C 96 LFBGA96 plastic SOT536-1 96 LFBGA96 plastic SOT536-1 74LVCH32244AEC PACKAGE MATERIAL PINNING SYMBOL 1999 Aug 31 DESCRIPTION nAn data inputs nYn data outputs GND ground (0 V) nOE 3-state output enable inputs (active LOW) VCC DC supply voltage 3 CODE Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A MNA471 handbook, full pagewidth 6 1A1 1A3 2A1 2A3 3A1 3A3 4A1 4A2 5A1 5A3 6A1 6A3 7A1 7A3 8A1 8A2 5 1A0 1A2 2A0 2A2 3A0 3A2 4A0 4A3 5A0 5A2 6A0 6A2 7A0 7A2 8A0 8A3 4 2OE GND VCC GND GND VCC GND 3OE 6OE GND VCC GND GND VCC GND 7OE 3 1OE GND VCC GND GND VCC GND 4OE 5OE GND VCC GND GND VCC GND 8OE 2 1Y0 1Y2 2Y0 2Y2 3Y0 3Y2 4Y0 4Y3 5Y0 5Y2 6Y0 6Y2 7Y0 7Y2 8Y0 8Y3 1 1Y1 1Y3 2Y1 2Y3 3Y1 3Y3 4Y1 4Y2 5Y1 5Y3 6Y1 6Y3 7Y1 7Y3 8Y1 8Y2 A B C D E F G H J K L M N P R T Fig.1 Pin configuration. 1A0 handbook, full pagewidth 1Y0 1A1 1Y1 1A2 1Y2 1A3 1Y3 A5 A6 B5 B6 A3 C5 C6 D5 D6 A4 A2 E5 A1 E6 B2 F5 B1 F6 1OE H4 2A0 2Y0 2A1 2Y1 2A2 2Y2 2A3 2Y3 2OE C2 G5 C1 G6 D2 H6 D1 H5 H3 3A0 3Y0 3A1 3Y1 3A2 3Y2 3A3 3Y3 E2 J5 E1 J6 F2 K5 F1 K6 3OE J3 4A0 4Y0 4A1 4Y1 4A2 4Y2 4A3 4Y3 G2 L5 G1 L6 H1 M5 H2 M6 4OE J4 5A0 5Y0 5A1 5Y1 5A2 5Y2 5A3 5Y3 J2 N5 J1 N6 K2 P5 K1 P6 5OE T4 6A0 6Y0 6A1 6Y1 6A2 6Y2 6A3 6Y3 6OE L2 R5 L1 R6 M2 T6 M1 T5 T3 7A0 7Y0 7A1 7Y1 7A2 7Y2 7A3 7Y3 N2 N1 P2 P1 7OE 8A0 8Y0 8A1 8Y1 8A2 8Y2 8A3 8Y3 R2 R1 T1 T2 8OE MNA472 Fig.2 Logic symbol. 1999 Aug 31 4 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state handbook, halfpage 74LVC32244A; 74LVCH32244A VCC data input to internal circuit MNA473 Fig.3 Bus hold circuit. 1999 Aug 31 5 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER CONDITIONS UNIT MIN. VCC DC supply voltage VI DC input voltage VO DC output voltage range; for max. speed performance for low-voltage applications 2.7 MAX. 3.6 V 1.2 3.6 V 0 5.5 V output HIGH or LOW state 0 VCC V 3-state 0 5.5 V Tamb operating ambient temperature see DC and AC characteristics per device -40 +85 C tr,tf (t/f) input rise and fall times ratio VCC = 1.2 to 2.7 V 0 20 ns/V VCC = 2.7 to 3.6 V 0 10 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134); voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER CONDITIONS MIN. -0.5 MAX. +6.5 UNIT VCC DC supply voltage V VI DC input voltage note 1 -0.5 +6.5 V IIK DC input diode current VI < 0 - -50 mA IOK DC output diode current VO > VCC or VO < 0; note 1 - 50 mA VO DC output voltage output HIGH or LOW state; note 1 -0.5 IO DC output source or sink current ICC, IGND DC VCC or GND current Tstg storage temperature PD power dissipation per packages VCC + 0.5 V output 3-state; note 1 -0.5 +6.5 V VO = 0 to VCC - 50 mA - 100 mA -65 +150 C - 1000 mW temperature range: -40 to +85 C; note 2 Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. Above 70 C the value of PD derates linearly with 1.8 mW/K. 1999 Aug 31 6 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A DC CHARACTERISTICS Over recommended operating conditions; voltage are referenced to GND (ground = 0 V). Tamb (C) TEST CONDITIONS SYMBOL OTHER VIH -40 to +85 PARAMETER HIGH-level input voltage VCC (V) - - - - - - GND 2.7 to 3.6 - - 0.8 1.2 VOH VOL LOW-level input voltage HIGH-level output voltage LOW-level output voltage TYP.(1) MAX. MIN. VCC 2.7 to 3.6 2.0 VIL UNIT 1.2 V V VI = VIH or VIL IO = -12 mA 2.7 VCC - 0.5 - - IO = -100 A 3.0 VCC - 0.2 VCC - IO = -18 mA 3.0 VCC - 0.6 - - IO = -24 mA 3.0 VCC - 0.8 - - IO = 12 mA 2.7 - - 0.40 IO = 100 A 3.0 - - 0.20 IO = 24 mA V VI = VIH or VIL V 3.0 - - 0.55 II input leakage current VI = 5.5 V or GND; note 2 3.6 - 0.1 5 A IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 5.5 V or GND 3.6 - 0.1 5 A Ioff power off leakage supply VI or VO = 5.5 V 0.0 - 0.1 10 A ICC quiescent supply current VI = VCC or GND; IO = 0 3.6 - 0.1 40 A ICC additional quiescent supply current per input pin VI = VCC - 0.6 V; IO = 0 2.7 to 3.6 - 5 500 A IBHL bus hold LOW sustaining current VI = 0.8 V; notes 3, 4 and 5 3.0 75 - - A IBHH bus hold HIGH sustaining current VI = 2.0 V; notes 3, 4 and 5 3.0 -75 - - A IBHLO bus hold LOW overdrive current notes 3, 4 and 6 3.6 500 - - A IBHHO bus hold HIGH overdrive current notes 3, 4 and 6 3.6 -500 - - A Notes 1. All typical values are at VCC = 3.3 V and Tamb = 25 C. 2. For bus hold parts the bus hold circuit is switched off when VI exceeds VCC allowing 5.5 V on the input terminal. 3. Valid for data inputs of bus hold parts only (LVCH32xxx-A). 4. For data inputs only. Control inputs do not have a bus hold circuit. 5. The specified sustaining current at the data input holds the input below the specified VI level. 6. The specified overdrive current at the data input forces the data input to the opposite logic input level. 1999 Aug 31 7 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A AC CHARACTERISTICS Ground = 0 V; tr = tf 2.5 ns; CL = 50 pF; RL = 500 . Tamb = -40 to +85 C TEST CONDITIONS SYMBOL PARAMETER WAVEFORMS tPHL/tPLH tPZH/tPZL tPHZ/tPLZ propagation delay nAn to nYn see Figs 4 and 6 3-state output enable time nOE to nYn see Figs 5 and 6 3-state output disable time nOE to nYn see Figs 5 and 6 VCC (V) MIN. 1.5 - 5.5 3.0 to 3.6 1.5 3.0 4.5 2.7 1.5 - 6.5 3.0 to 3.6 1.5 3.5 5.5 2.7 1.5 - 6.2 3.0 to 3.6 1.5 3.7 5.2 1. All typical values are measured at VCC = 3.3 V and Tamb = 25 C. AC WAVEFORMS handbook, halfpage VI VM GND t PHL t PLH VOH nYn OUTPUT VM VOL MNA474 VM = 1.5 V at VCC 2.7 V or VM = 0.5 x VCC at VCC < 2.7 V. VOL and VOH are typical output voltage drop that occur with the output load. Fig.4 Input nAn to output nYn propagation delay times. 1999 Aug 31 8 UNIT MAX. 2.7 Notes nAn INPUT TYP.(1) ns ns ns Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A VI handbook, full pagewidth nOE INPUT VM GND t PLZ t PZL VCC OUTPUT LOW-to-OFF OFF-to-LOW VM VX VOL t PZH t PHZ VOH VY OUTPUT HIGH-to-OFF OFF-to-HIGH GND VM outputs enabled outputs enabled outputs disabled MNA478 VM = 1.5 V at VCC 2.7 V or VM = 0.5 x VCC at VCC < 2.7 V; VX = VOL + 0.3 V at VCC 2.7 V or VX = VOL + 0.1 V at VCC < 2.7 V; VY = VOH - 0.3 V at VCC 2.7 V or VY = VOH - 0.1 V at VCC < 2.7 V. VOL and VOH are typical output voltage drop that occur with the output load. Fig.5 3-state enable and disable times. S1 handbook, full pagewidth VCC PULSE GENERATOR VI RL 500 VO 2 x VCC open GND D.U.T. CL 50 pF RT RL 500 MNA479 TEST S1 VCC Definitions for test circuit: RL = load resistor. CL = load capacitance including jig and probe capacitance. RT = termination resistance should be equal to the output impedance Zo of the pulse generator. VI tPLH/tPHL open tPLZ/tPZL 2 x VCC < 2.7 V tPHZ/tPZH GND 2.7 to 3.6 V 2.7 V VCC Fig.6 Load circuitry for switching times. 1999 Aug 31 9 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A PACKAGE OUTLINE LFBGA96: plastic low profile fine-pitch ball grid array package; 96 balls; body 13.5 x 5.5 x 1.05 mm SOT536-1 D ball A1 index area A2 A E A1 detail X b A w M ZD e y v A ZE T R P N M L K J H G F E D C B A e X 1 2 3 4 5 6 DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 b D E e v w y ZD ZE mm 1.5 0.41 0.31 1.2 0.9 0.51 0.41 5.6 5.4 13.6 13.4 0.8 0.2 0.15 0.1 0.93 0.58 0.93 0.58 OUTLINE VERSION REFERENCES IEC JEDEC EIAJ 5 10 mm scale EUROPEAN PROJECTION ISSUE DATE 98-11-25 99-06-03 SOT536-1 1999 Aug 31 0 10 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state SOLDERING 74LVC32244A; 74LVCH32244A If wave soldering is used the following conditions must be observed for optimal results: Introduction to soldering surface mount packages * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). * For packages with leads on two sides and a pitch (e): - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. Reflow soldering The footprint must incorporate solder thieves at the downstream end. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical reflow peak temperatures range from 215 to 250 C. The top-surface temperature of the packages should preferable be kept below 230 C. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Wave soldering Manual soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. To overcome these problems the double-wave soldering method was specifically developed. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. 1999 Aug 31 11 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state 74LVC32244A; 74LVCH32244A Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE REFLOW(1) WAVE BGA, LFBGA, SQFP, TFBGA not suitable suitable(2) HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, SMS not PLCC(3), SO, SOJ suitable LQFP, QFP, TQFP SSOP, TSSOP, VSO suitable suitable suitable not recommended(3)(4) suitable not recommended(5) suitable Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1999 Aug 31 12 Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state NOTES 1999 Aug 31 13 74LVC32244A; 74LVCH32244A Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state NOTES 1999 Aug 31 14 74LVC32244A; 74LVCH32244A Philips Semiconductors Product specification 32-bit buffer/line driver; 5 V input/output tolerant; 3-state NOTES 1999 Aug 31 15 74LVC32244A; 74LVCH32244A Philips Semiconductors - a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 62 5344, Fax.+381 11 63 5777 For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Internet: http://www.semiconductors.philips.com SCA 67 (c) Philips Electronics N.V. 1999 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 245004/01/pp16 Date of release: 1999 Aug 31 Document order number: 9397 750 06258