Original Creation Date: 06/29/95
Last Update Date: 12/10/96
Last Major Revision Date: 06/29/95
MNLM109-H REV 0AL MILITARY DATA SHEET
5 VOLT REGULATOR
NS Part Numbers
LM109H/883
Industry Part Number
LM109
Prime Die
LM109
Processing
MIL-STD-883, Method 5004
Quality Conformance Inspection
MIL-STD-883, Method 5005
Subgrp Description Temp ( C)
o
1 Static tests at +25
2 Static tests at +125
3 Static tests at -55
4 Dynamic tests at +25
5 Dynamic tests at +125
6 Dynamic tests at -55
7 Functional tests at +25
8A Functional tests at +125
8B Functional tests at -55
9 Switching tests at +25
10 Switching tests at +125
11 Switching tests at -55
1
MNLM109-H REV 0AL MILITARY DATA SHEET
Electrical Characteristics
DC/AC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: Il = 5mA. Pre-Burn-In Stress Test per (SG) RPI-3-371.
AC: Il = 5mA. Pre-Burn-In Stress Test per (SG) RPI-3-371.
SYMBOL PARAMETER CONDITIONS NOTES PIN-
NAME MIN MAX UNIT SUB-
GROUPS
Vstart Start Up Input
Voltage Vout > 4.706V, Rl = 5 Ohms 19V1
Iq Quiescent Current Vin = 7V -10 mA 1, 2,
3
Vin = 7.2V, Il = 500mA 2 -10 mA 1, 2,
3
Vin = 25V -10 mA 1, 2,
3
Vin = 25V, Il = 500mA 2 -10 mA 1, 2,
3
Vin = 35V -10 mA 1
Delta Iq Quiescent Current
Change 7V < Vin < 25 V -0.5 0.5 mA 1, 2,
3
Vin = 7.2V, 5mA < Il < 500mA 2 -0.8 0.8 mA 1, 2,
3
Vrline Line Regulation 7V < Vin < 25V -50 50 mV 1
7V < Vin < 25V -100 100 mV 2, 3
Vrload Load Regulation Vin = 7.2V, 5mA < Il < 500mA 2 -50 50 mV 1
Vin = 7.2V, 5mA < Il < 500mA 2 -100 -100 mV 2, 3
Vin = 10V, 5mA < Il < 500 mA -50 50 mV 1
Vin = 10V, 5mA < Il < 500 mA -100 100 mV 2, 3
Vin = 25V, 20mA < Il < 500 mA -150 150 mV 1
Vin = 25V, 500mA > Il > 20 mA,
(tpw < 10mS) 2 -50 50 mV 1
Vout Output Voltage Vin = 7V, P1 < 2W 4.6 5.4 V 1, 2,
3
Vin = 7.2V, Il = 500mA, P < 2W 4.6 5.4 V 1, 2,
3
Vin = 10V, Il = 100mA, P < 2W 2 4.7 5.3 V 1
Vin = 25V, Il = 20mA, P < 2W 4.6 5.4 V 1
Vin = 25V, Il = 500mA, P < 2W,
(tpw < 10mS) 4.6 5.4 V 1, 2,
3
Vin = 25V, P < 2W 2 4.6 5.4 V 1, 2,
3
Ios Short Circuit
Current Vin = 35V 2 A 1
Rr Ripple Rejection f < 120Hz, ein=1V(rms), Il=125mA 550 dB4
2
MNLM109-H REV 0AL MILITARY DATA SHEET
Note 1: This test is performed by shifting the input voltage in 50 mV increments until output
reaches 4.706V.
Note 2: At -55 C & 125 C, Il = 200mA rather than 500mA.
Note 3: Guaranteed parameter not tested.
Note 4: Pre-Burn-In Stress Test per (SG) RPI-3-371.
Note 5: Bench test, use 70256655.
3
MILITARY DATA SHEET
MNLM109-H REV 0AL
Graphics and Diagrams
GRAPHICS# DESCRIPTION
08346HR (blank)
MKT-H03RB (blank)
See attached graphics following this page.
4
