Notice for TAIYO YUDEN Products
[ For High Quality and/or Reliability Equipment
(Automotive / Industrial Equipment) ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
Product information in this catalog is as of October 2017. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment), medical
equipment classified as Class I or II by IMDRF, industrial equipment, and automotive interior applications, etc.
Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which
may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
medical equipment classified as Class III by IMDRF).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-ight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter TAIYO YUDENs ofcial sales channel). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDENs official sales
channel.
Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to U.S. Export
Administration Regulations, Foreign Exchange and Foreign Trade Control Law of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
1
8
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)
PART NUMBER *Operating Temp. : -40105℃(Including self-generated heat
C B
2 0 1 2
T
1 0 0
M
V △=Blank space
Series name
Code Series name
CB Wound chip power inductor
Characteristics
Code Characteristics
△△ Standard
C High current
DimensionsL×W
Code Typeinch Dimensions
L×W)[mm
2012 20120805 2.0×1.25
2016 20160806 2.0×1.6
2518 25181007 2.5×1.8
3225 32251210 3.2×2.5
Packaging
Code Packaging
T Taping
Nominal inductance
Code
example Nominal inductance[μH
1R0 1.0
100 10
101 100
RDecimal point
Inductance tolerance
Code Inductance tolerance
K ±10
M ±20
Special code
Code Special code
Standard
R Low Rdc type
Internal code
Code Internal code
V Inductor for Industrial and Automotive
STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
Recommended Land Patterns
Surface Mounting
Mounting and soldering conditions should be checked beforehand.
Applicable soldering process to these products is reflow soldering only.
Type A B C
2012 0.60 1.0 1.45
2016 0.60 1.0 1.8
2518 0.60 1.5 2.0
3225 0.85 1.7 2.7
Unitmm
Type L W T e Standard quantity [pcs]
Paper tape Embossed tape
CB 2012
CB C2012
2.0±0.2
0.079±0.008
1.25±0.2
0.049±0.008
1.25±0.2
0.049±0.008
0.5±0.2
0.020±0.008 3000
CB 2016
CB C2016
2.0±0.2
0.079±0.008
1.6±0.2
0.063±0.008
1.6±0.2
0.063±0.008
0.5±0.2
0.020±0.008 2000
CB 2518
CB C2518
2.5±0.2
0.098±0.008
1.8±0.2
0.071±0.008
1.8±0.2
0.071±0.008
0.5±0.2
0.020±0.008 2000
CB C3225 3.2±0.2
0.126±0.008
2.5±0.2
0.098±0.008
2.5±0.2
0.098±0.008
0.6±0.3
0.024±0.012 1000
Unitmminch
INDUCTORS
POWER INDUCTORS
Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
WIRE-WOUND CHIP POWER INDUCTORS(CB SERIES)
REFLOW
55
1
8
PART NUMBER
・ All the Wire-wound Chip Power Inductors of the catalog lineup are RoHS compliant.
Note)
・ The exchange of individual specifications is necessary depending on the application and circuit condition. Please contact Taiyo Yuden sales channels.
・ *2: Industrial products and Medical products
   Please consult with TAIYO YUDEN’s official sales channel for the details of the product specification , etc.,
   and please review and approve TAIYO YUDEN's product specification before ordering.
Please be sure to contact us for further information before using the components for Automotive equipment.
2012(0805)type
Saturation current
Idc1
Temperature rise current
Idc2
CB 2012T1R0M V 1.0 ±20% 100 0.15 500 700 7.96 *2
CB 2012T2R2M V 2.2 ±20% 80 0.23 410 620 7.96 *2
CB 2012T3R3M V 3.3 ±20% 55 0.30 330 550 7.96 *2
CB 2012T4R7M V 4.7 ±20% 45 0.40 300 430 7.96 *2
CB 2012T6R8M V 6.8 ±20% 38 0.47 250 350 7.96 *2
CB 2012T100[] V 10 ±10%,±20% 32 0.70 190 300 2.52 *2
CB 2012T100[]RV 10 ±10%,±20% 32 0.50 200 300 2.52 *2
CB 2012T150[] V 15 ±10%,±20% 28 1.3 170 240 2.52 *2
CB 2012T220[] V 22 ±10%,±20% 16 1.7 135 220 2.52 *2
CB 2012T470[] V 47 ±10%,±20% 11 3.7 90 140 2.52 *2
CB 2012T680[] V 68 ±10%,±20% 10 6.0 70 100 2.52 *2
CB 2012T101[] V 100 ±10%,±20% 87.0 60 100 0.796 *2
Saturation current
Idc1
Temperature rise current
Idc2
CB C2012T1R0M V 1.0 ±20% 100 0.19 700 640 7.96 *2
CB C2012T2R2M V 2.2 ±20% 70 0.33 530 485 7.96 *2
CB C2012T4R7M V 4.7 ±20% 45 0.50 360 395 7.96 *2
CB C2012T100[] V 10 ±10%,±20% 40 1.2 240 255 2.52 *2
CB C2012T220[] V 22 ±10%,±20% 16 3.7 170 145 2.52 *2
CB C2012T470[] V 47 ±10%,±20% 11 5.8 120 115 2.52 *2
2016(0806)type
Saturation current
Idc1
Temperature rise current
Idc2
CB 2016T1R0M V 1.0 ±20% 100 0.09 600 720 7.96 *2
CB 2016T1R5M V 1.5 ±20% 80 0.11 550 650 7.96 *2
CB 2016T2R2M V 2.2 ±20% 70 0.13 510 600 7.96 *2
CB 2016T3R3M V 3.3 ±20% 55 0.20 400 440 7.96 *2
CB 2016T4R7M V 4.7 ±20% 45 0.25 340 410 7.96 *2
CB 2016T6R8M V 6.8 ±20% 38 0.35 300 330 7.96 *2
CB 2016T100[] V 10 ±10%,±20% 32 0.50 250 270 2.52 *2
CB 2016T150[] V 15 ±10%,±20% 28 0.70 210 220 2.52 *2
CB 2016T220[] V 22 ±10%,±20% 16 1.0 165 190 2.52 *2
CB 2016T330[] V 33 ±10%,±20% 14 1.7 130 140 2.52 *2
CB 2016T470[] V 47 ±10%,±20% 11 2.4 110 120 2.52 *2
CB 2016T680[] V 68 ±10%,±20% 10 3.0 90 110 2.52 *2
CB 2016T101[] V 100 ±10%,±20% 84.5 70 90 0.796 *2
Saturation current
Idc1
Temperature rise current
Idc2
CB C2016T1R0M V 1.0 ±20% 100 0.10 1,100 885 7.96 *2
CB C2016T1R5M V 1.5 ±20% 80 0.15 1,000 775 7.96 *2
CB C2016T2R2M V 2.2 ±20% 70 0.20 750 625 7.96 *2
CB C2016T3R3M V 3.3 ±20% 55 0.27 600 535 7.96 *2
CB C2016T4R7M V 4.7 ±20% 45 0.37 550 460 7.96 *2
CB C2016T6R8M V 6.8 ±20% 38 0.59 450 360 7.96 *2
CB C2016T100[] V 10 ±10%,±20% 32 0.82 380 305 2.52 *2
CB C2016T150[] V 15 ±10%,±20% 28 1.2 300 255 2.52 *2
CB C2016T220[] V 22 ±10%,±20% 16 1.8 250 205 2.52 *2
CB C2016T330[] V 33 ±10%,±20% 14 2.8 220 165 2.52 *2
CB C2016T470[] V 47 ±10%,±20% 11 4.3 150 130 2.52 *2
CB C2016T680[] V 68 ±10%,±20% 10 7.0 130 105 2.52 *2
CB C2016T101[] V 100 ±10%,±20% 88.0 110 95 0.796 *2
・ [] Please specify the Inductance tolerance code(Kor M)
※)The saturation current value(Idc1) is the DC current value having inductance decrease down to 30%.( at 20℃)
※)The temperature rise current value(Idc2) is the DC current value having temperature increase by 20℃.( at 20℃)
※)The rated current value is following either Idc1 or Idc2, which is the lower one.
Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA] Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA]
Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA] Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA]
INDUCTORS
POWER INDUCTORS
Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
56
1
8
PART NUMBER
2518(1007)type
Saturation current
Idc1
Temperature rise current
Idc2
CB 2518T1R0M V 1.0 ±20% 100 0.06 1,200 1,250 7.96 *2
CB 2518T1R5M V 1.5 ±20% 80 0.07 650 1,100 7.96 *2
CB 2518T2R2M V 2.2 ±20% 68 0.09 510 1,000 7.96 *2
CB 2518T3R3M V 3.3 ±20% 54 0.11 440 900 7.96 *2
CB 2518T4R7MRV 4.7 ±20% 46 0.10 310 820 7.96 *2
CB 2518T4R7M V 4.7 ±20% 46 0.13 340 820 7.96 *2
CB 2518T6R8M V 6.8 ±20% 38 0.15 270 750 7.96 *2
CB 2518T100[] V 10 ±10%,±20% 30 0.25 250 600 2.52 *2
CB 2518T150[] V 15 ±10%,±20% 23 0.32 180 500 2.52 *2
CB 2518T220[] V 22 ±10%,±20% 19 0.50 165 390 2.52 *2
CB 2518T330[] V 33 ±10%,±20% 15 0.70 130 320 2.52 *2
CB 2518T470[] V 47 ±10%,±20% 12 0.95 110 270 2.52 *2
CB 2518T680[] V 68 ±10%,±20% 9.5 1.5 70 210 2.52 *2
CB 2518T101[] V 100 ±10%,±20% 9.0 2.1 60 190 0.796 *2
CB 2518T151[] V 150 ±10%,±20% 7.0 3.2 55 140 0.796 *2
CB 2518T221[] V 220 ±10%,±20% 5.5 4.5 50 110 0.796 *2
CB 2518T331[] V 330 ±10%,±20% 4.5 7.0 40 90 0.796 *2
CB 2518T471[] V 470 ±10%,±20% 3.5 10 35 70 0.796 *2
CB 2518T681[] V 680 ±10%,±20% 3.0 17 30 50 0.796 *2
CB 2518T102[] V 1000 ±10%,±20% 2.4 24 25 45 0.252 *2
Saturation current
Idc1
Temperature rise current
Idc2
CB C2518T1R0M V 1.0 ±20% 100 0.08 1,000 775 7.96 *2
CB C2518T1R5M V 1.5 ±20% 80 0.11 950 730 7.96 *2
CB C2518T2R2M V 2.2 ±20% 68 0.13 890 630 7.96 *2
CB C2518T3R3M V 3.3 ±20% 54 0.16 730 560 7.96 *2
CB C2518T4R7M V 4.7 ±20% 41 0.20 680 510 7.96 *2
CB C2518T6R8M V 6.8 ±20% 38 0.30 550 420 7.96 *2
CB C2518T100[] V 10 ±10%,±20% 30 0.36 480 375 2.52 *2
CB C2518T150[] V 15 ±10%,±20% 23 0.65 350 285 2.52 *2
CB C2518T220[] V 22 ±10%,±20% 19 0.77 320 250 2.52 *2
CB C2518T330[] V 33 ±10%,±20% 15 1.5 270 185 2.52 *2
CB C2518T470[] V 47 ±10%,±20% 12 1.9 240 165 2.52 *2
CB C2518T680[] V 68 ±10%,±20% 9.5 2.8 200 140 2.52 *2
CB C2518T101[] V 100 ±10%,±20% 9.0 3.7 160 125 0.796 *2
CB C2518T151[] V 150 ±10%,±20% 7.0 6.1 140 95 0.796 *2
CB C2518T221[] V 220 ±10%,±20% 5.5 8.4 115 80 0.796 *2
CB C2518T331[] V 330 ±10%,±20% 4.5 12.3 100 65 0.796 *2
CB C2518T471[] V 470 ±10%,±20% 3.5 22 80 50 0.796 *2
CB C2518T681[] V 680 ±10%,±20% 3.0 28 65 45 0.796 *2
3225(1210)type
Saturation current
Idc1
Temperature rise current
Idc2
CB C3225T1R0MRV 1.0 ±20% 250 0.055 2,000 1,100 0.1 *2
CB C3225T1R5MRV 1.5 ±20% 220 0.060 2,000 1,000 0.1 *2
CB C3225T2R2MRV 2.2 ±20% 190 0.080 2,000 930 0.1 *2
CB C3225T3R3MRV 3.3 ±20% 160 0.095 2,000 850 0.1 *2
CB C3225T4R7MRV 4.7 ±20% 70 0.100 1,250 830 0.1 *2
CB C3225T6R8MRV 6.8 ±20% 50 0.120 950 760 0.1 *2
CB C3225T100[]RV 10 ±10%,±20% 23 0.133 900 720 0.1 *2
CB C3225T150[]RV 15 ±10%,±20% 20 0.195 730 590 0.1 *2
CB C3225T220[]RV 22 ±10%,±20% 17 0.27 620 500 0.1 *2
CB C3225T330[]RV 33 ±10%,±20% 13 0.41 500 400 0.1 *2
CB C3225T470[]RV 47 ±10%,±20% 10 0.67 390 320 0.1 *2
CB C3225T680[]RV 68 ±10%,±20% 8.0 1.0 320 260 0.1 *2
CB C3225T101[]RV 100 ±10%,±20% 6.0 1.4 270 220 0.1 *2
CB C3225T221[]RV 220 ±10%,±20% 3.0 2.5 190 170 0.1 *2
CB C3225T821[]RV 820 ±10%,±20% 1.8 12 110 80 0.1 *2
CB C3225T102[]RV 1000 ±10%,±20% 1.6 13 100 75 0.1 *2
・ [] Please specify the Inductance tolerance code(Kor M)
※)The saturation current value(Idc1) is the DC current value having inductance decrease down to 30%.( at 20℃)
※)The temperature rise current value(Idc2) is the DC current value having temperature increase by 20℃.( at 20℃)
※)The rated current value is following either Idc1 or Idc2, which is the lower one.
Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA]
Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA] Measuring
frequency[MHz] Note
Part number Nominal inductance
[μH] Inductance tolerance
Self-resonant
frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current ※) [mA]
INDUCTORS
POWER INDUCTORS
Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
57
1
8
INDUCTORS
POWER INDUCTORS
Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecicationsheets.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
Derating of Rated Current
CB series
Derating of current is necessary for CB series depending on ambient temperature.
Please refer to the chart shown below for appropriate derating of current.
58
1
8
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current
(%)
CB 2012 type
Idc1
Idc2
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current (%)
CB C2012 type
Idc1
Idc2
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current (%)
CB 2016 type
Idc1
Idc2
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current
(%)
CB C2016 type
Idc1
Idc2
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current
(%)
CB 2518 type
Idc1
Idc2
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current (%)
CB C2518 type
Idc1
Idc2
-40 -20 0 20 40 60 80 100 120
120
100
80
60
40
20
0
Ambient Temperature ()
Ratio to rated current (%)
CB C3225 type
Idc1
Idc2
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
WIRE-WOUND CHIP INDUCTORS (LB SERIES),
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES),
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
PACKAGING
①Minimum Quantity
Type Standard Quantity [pcs]
Paper Tape Embossed Tape
LB C3225
CB C3225 1000
LB 3218 2000
LB R2518
LB C2518
LB 2518
CB 2518
CB C2518
2000
LBM2016
LB C2016
LB 2016
CB 2016
CB C2016
2000
LB 2012
LB C2012
LB R2012
CB 2012
CB C2012
3000
CB L2012 4000
LB 1608 4000
LBMF1608
CBMF1608 3000
②Tape material
Embossed tape
Top tape
Base tape
Sprocket hole
Chip cavity
Chip
Chip Filled
Card board carrier tape
Top tape
Base tape
Sprocket hole
Bottom tape Chip cavity
Chip
Chip Filled
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
③Taping Dimensions
Embossed Tape (0.315 inches wide)
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
Type Chip cavity Insertion pitch Tape thickness
A B F T K
LBM2016 1.75±0.1
(0.069±0.004)
2.1±0.1
(0.083±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
1.9max.
(0.075max.)
LB C3225
CB C3225
2.8±0.1
(0.110±0.004)
3.5±0.1
(0.138±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
4.0max.
(0.157max.)
LB 3218 2.1±0.1
(0.083±0.004)
3.5±0.1
(0.138±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
2.2max.
(0.087max.)
LB 2518
CB 2518
LB C2518
CB C2518
LB R2518
2.15±0.1
(0.085±0.004)
2.7±0.1
(0.106±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
2.2max.
(0.087max.)
LB 2016
CB 2016
LB C2016
CB C2016
1.75±0.1
(0.069±0.004)
2.1±0.1
(0.083±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
1.9max.
(0.075max.)
LB 2012
CB 2012
LB C2012
CB C2012
LB R2012
1.45±0.1
(0.057±0.004)
2.25±0.1
(0.089±0.004)
4.0±0.1
(0.157±0.004)
0.25±0.05
(0.010±0.002)
1.45max.
(0.057max.)
LBMF1608
CBMF1608
1.1±0.1
(0.043±0.004)
1.9±0.1
(0.075±0.004)
4.0±0.1
(0.157±0.004)
0.25±0.05
(0.010±0.002)
1.2max.
(0.047max.)
Unit:mm(inch)
Card board carrier tape(0.315 inches wide)
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
T
Type Chip cavity Insertion pitch Tape thickness
A B F T
CB L2012 1.55±0.1
(0.061±0.004)
2.3±0.1
(0.091±0.004)
4.0±0.1
(0.157±0.004)
1.1max.
(0.043max.)
LB 1608 1.0±0.1
(0.039±0.004)
1.8±0.1
(0.071±0.004)
4.0±0.1
(0.157±0.004)
1.1max.
(0.043max.)
Unit:mm(inch)
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
④Leader and Blank Portion
⑤Reel Size
⑥Top Tape Strength
The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
hq_i_wound_CB_LB_reli_e.doc
WIRE-WOUND CHIP INDUCTORS (LB SERIES),
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES),
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
RELIABILITY DATA
1.Operating temperature Range
Specified Value
LB, LBC, LBR Series
40~+105℃(Including self-generated heat
CB, CBC Series
LBM Series
Test Methods and
Remarks Including self-generated heat
2. Storage Temperature Rangeafter soldering
Specified Value
LB, LBC, LBR Series
40~+85 CB, CBC Series
LBM Series
Test Methods and
Remarks
LB, CB Series
Please refer the term of "7. storage conditions" in precautions.
3.Rated Current
Specified Value
LB, LBC, LBR Series
Within the specified tolerance
CB, CBC Series
LBM Series
4.Inductance
Specified Value
LB, LBC, LBR Series
Within the specified tolerance CB, CBC Series
LBM Series
Test Methods and
Remarks
LBLBCLBRCBCBCLBM Series
Measuring equipment
LCR MaterHP4285A or its equivalent
5.Q
Specified Value
LB, LBC, LBR Series
CB, CBC Series
LBM Series Within the specified tolerance
Test Methods and
Remarks
LBM Series
Measuring equipment
:
LCR MaterHP4285A or its equivalent
6.DC Resistance
Specified Value
LB, LBC, LBR Series
Within the specified tolerance CB, CBC Series
LBM Series
Test Methods and
Remarks Measuring equipment : DC Ohmmeter HIOKI 3227 or its equivalent
7.Self-Resonant Frequency
Specified Value
LB, LBC, LBR Series
Within the specified tolerance CB, CBC Series
LBM Series
Test Methods and
Remarks Measuring equipment : Impedance analyzer HP4291A or its equivalent
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
hq_i_wound_CB_LB_reli_e.doc
8.Temperature Characteristic
Specified Value
LBM2016 Inductance change : Within±10
LB2012 LBR2012 CB2012 LB2016
Inductance change : Within±20
CB2016 LB2518 LBR2518 CB2518
LBC3225 CBC3225
LBC2016 CBC2016 LBC2518 CBC2518 Inductance change : Within±25
LB3218
LBC2012 CBC2012 Inductance change : Within±35
Test Methods and
Remarks
Change of maximum inductance deviation in step 1-5
Step Temperature(℃)
LB, CB Serie
1 20
2 40
3 20Reference temperature
4 85Maximum operating temperature
5 20
9.Rasistance to Flexure of Substrate
Specified Value
LB, LBC, LBR Series
No damage. CB, CBC Series
LBM Series
Test Methods and
Remarks
Warp
: 2mm
LBLBCLBRCBCBCLBM Series
Test substrate
: Board according to JIS C0051
Thickness
:
1.0mm
10.Body Strength
Specified Value
LB, LBC, LBR Series
No damage. CB, CBC Series
LBM Series
Test Methods and
Remarks
LBLBCLBRCBCBCLBM
Applied force
:
10N
Duration
: 10sec.
11.Adhesion of terminal electrode
Specified Value
LB, LBC, LBR Series
No abnormality. CB, CBC Series
LBM Series
Test Methods and
Remarks
LBLBCLBRCBCBCCBLLBM
Applied force
:
10N to X and Y directions
Duration
5 sec.
Test substrate
: Printed board
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
hq_i_wound_CB_LB_reli_e.doc
12.Resistance to vibration
Specified Value
LB, LBC, LBR Series Inductance change : Within±20
No significant abnormality in appearance.
CB, CBC Series
LBM Series Inductance change : Within±20
No significant abnormality in appearance.
Test Methods and
Remarks
LBLBRLBCCBCBCLBM : According to JIS C5102 clause 8.2.
Vibration type
:
A
Directions
: 2 hrs each in X, Y and Z directions. Total
6 hrs
Frequency range
: 10 to 55 to 10 Hz
1min.
Amplitude
: 1.5mm
Mounting method
: Soldering onto printed board
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48
hrs.
13.Drop test
Specified Value
LB, LBC, LBR Series
CB, CBC Series
LBM Series
14.Solderability
Specified Value
LB, LBC, LBR Series
At least 90 of surface of terminal electrode is covered by new
CB, CBC Series
LBM Series
Test Methods and
Remarks
LBLBCLBRCBCBCCBLLBM
Solder temperature
:
245±5
Duration
:
0.5sec
Flux
:
Methanol solution with 25 of colophony
15.Resistance to soldering
Specified Value
LB, LBC, LBR Series Inductance change : Within±20
CB, CBC Series
LBM Series Inductance change : Within±20
Test Methods and
Remarks
LBLBCLBRCBCBCCBLLBM
3 times of reflow oven at 230 MIN for 40sec. with peak temperature at 260 for 5sec.
16.Resisitance to solvent
Specified Value
LB, LBC, LBR Series
CB, CBC Series
LBM Series
Test Methods and
Remarks
Solvent te
mperature
:
Room temperature
Type of solvent
: Isopropyl alcohol
Cleaning conditions
: 90s. Immersion and cleaning.
17.Thermal shock
Specified Value
LB, LBC, LBR Series
Inductance change : Within±20
No significant abnormality in appearance.
CB, CBC Series
LBM Series
Test Methods and
Remarks
LBLBCLBRCBCBCCBLLBM:-40~+85, maintain times 30min. ,100 cycle
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
hq_i_wound_CB_LB_reli_e.doc
18.Damp heat life test
Specified Value
LB, LBC, LBR Series
Inductance change : Within±20
No significant abnormality in appearance.
CB, CBC Series
LBM Series
Test Methods and
Remarks
Temperature
:
60±2
Humidity
: 90
95RH
Duration
: 1000 h
rs
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
19.Loading under damp heat life test
Specified Value
LB, LBC, LBR Series
Inductance change : Within±20
No significant abnormality in appearance.
CB, CBC Series
LBM Series
Test Methods and
Remarks
Temperature
:
60±2
Humidity
: 90
95RH
Duration
: 1000 hrs
Applied current
: Rated current
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
20.High temperature life test
Specified Value
LB, LBC, LBR Series
CB, CBC Series Inductance change : Within±20
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
Temperature
:
85±2
Duration
: 1000 hrs
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
21.Loading at high temperature life test
Specified Value
LB, LBC, LBR Series Inductance change : Within±20
No significant abnormality in appearance.
CB, CBC Series
LBM Series
Test Methods and
Remarks
Temperature
:
85±2
Duration
: 1000 hrs
Applied current
: Rated current
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
22.Low temperature life test
Specified Value
LB, LBC, LBR Series
Inductance change : Within±20
No significant abnormality in appearance.
CB, CBC Series
LBM Series
Test Methods and
Remarks
Temperature
:
40±2
Duration
: 1000 hrs
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
23.Standard condition
Specified Value
LB, LBC, LBR Series Standard test conditions
Unless specified, Ambient temperature is 20±15
and the Relative
humidity is 65±20
. If there is any doubt about the test results, further
measurement shall be had within the following limits:
Ambient Temperature: 20±2
Relative humidity: 65±5
Inductance value is based on our standard measurement systems.
CB, CBC Series
LBM Series
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
hq_i_wound_CB_LB_prec_e.doc
WIRE-WOUND CHIP INDUCTORS (LB SERIES)
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
PRECAUTIONS
1Circuit Design
Precautions
Operating environment
1. The products listed in this catalogue are intended for use in general electronic equipment
(e.g., AV equipment, OA equipment, home electric
appliances, office equipment, information and communication equipment), general medical
equipment, industrial equipment, and automotive
interior applications, etc.
Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause
loss of human life or bodily injury (e.g., specially controlled medical equipment, transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment,
aviation equipment, nuclear control eq