Standard Power Integrated Module flowPIM 0 (R) Features/ Eigenschaften - 1/3 Phases Input Rectifier brake chopper 3 phases inverter IGBT + FRED with open emitter NTC Copyright by Vincotech Tyco Electronics Finsinger Feld 1, D-85521 Ottobrunn Revision:1 power.switches@tycoelectronics.com flowPIM(R) 0 V23990-P54X-A module types / Produkttypen part - number V23990-P541-A-PM V23990-P542-A-PM V23990-P543-A-PM V23990-P544-A-PM V23990-P545-A-PM V23990-P548-A-PM V23990-P549-A-PM V23990-P540-A-PM Voltage 600V 600V 600V 600V 600V 1200V 1200V 1200V current 5A 7A 10A 15A 20A 5A 10A 15A Schematics/ Schaltplane Tyco Electronics Copyright by Vincotech Finsinger Feld 1, D-85521 Ottobrunn power.switches@tycoelectronics.com Revision:1 V23990-P54X-A flowPIM(R) 0 Outline / Pinout Tyco Electronics Copyright by Vincotech Finsinger Feld 1, D-85521 Ottobrunn power.switches@tycoelectronics.com Revision:1 flowPIM(R) 0 V23990-P54X-A Montagehinweise / Handling Instruction Montagehinweise... ... fur die Leiterplatte x Das Modul muss vor dem Lotvorgang zuerst in die Locher der Leiterplatte eingerastet werden. Siehe unten x Nach dem Einrasten mussen alle Kontaktpins eingelotet werden. x Die Pins durfen wahrend und nach der Montage bei einer max. Modultemperatur von 25C nicht mehr als 0.2 mm bzw 35 N gedehnt bzw gestaucht werden. x Die Pins durfen bei einer max. Substrattemperatur von 100C mit nicht mehr als 5 N auf Dauer belastet werden. x Eine Vibrationsbelastung der Pins ist unbedingt zu vermeiden. Handling Instructions... ... to the PCB x The module must be fixed to the PCB by clipping into the adequate holes before pin soldering. See below x After fixing all pins must be soldered into the PCB. x During assembly, at a max. module temperature of 25C, the pins should not be drawn or pushed more than 0.2 mm or loaded with a higher force than 35N. x At a maximum substrate-temperature of 100C the load of the pin should not exceed 5N. ...fur den Kuhlkorper x Die Montageflache des Kuhlkorpers mu sauber und frei von Partikeln sein. x Die Ebenheit mu < 0.05 mm auf einer Lange von 100 mm betragen. x die Rauhigkeit sollte geringer als RZ = 0.01 mm sein. ...to the heat sink x the heat sink surface must be clean and particle less. x the flatness must be < 0.05 mm for 100 mm continuous. x the surface roughness should be less than RZ = 0.01 mm. ...fur die Warmeleitpaste x homogene Verteilung der Warmeleitpaste auf der ganzen Modulbodenplatte mit einer max. Dicke von 0.05 mm. x Dickere Warmeleitpaste erhoht den Rth. ...to the thermal paste x homogenous applying of the thermal conducting paste over the whole module plate with a thickness of max. 0.05 mm. x Thicker thermal paste can raise the value of the Rth. ... fur die Befestigungsschrauben zum Kuhlkorper mit flacher Unterlegscheibe und wahlweise Federring x zuerst die Schrauben mit halbem Drehmoment festziehen. x dann mit max. Drehmoment festziehen (falls moglich nach 3 Stunden noch einmal festziehen). ...to the fastening screws to the heat sink if plain washer is used and optional with a spring lock washer x tighten crossover with the half torque first. Wichtige Parameter Important parameter Befestigungsschrauben / screw Schraubenunterlegscheibe / flat washer Federring / spring washer Anzugsdrehmoment / mounting torque M4 DIN 7985 DIN 125 or DIN 433 DIN 127 or DIN 128 Ma =2.0-2.2Nm Tyco by Electronics Copyright Vincotech x Vibration stress on pins is not allowed x tighten crossover with max. torque second (if possible, after 3 hours again) Finsinger Feld 1, D-85521 Ottobrunn power.switches@tycoelectronics.com Revision:1 V23990-P54X-A flowPIM(R) 0 PCB holes Copyright by Vincotech Tyco Electronics Finsinger Feld 1, D-85521 Ottobrunn power.switches@tycoelectronics.com Revision:1 V23990-P54X-A flowPIM(R) 0 Mounting 1. Insert the modul pins to the PCB 2. Press one short side of the modul gently as shown on figure 1.a. and 1.b. until two clips of that side are locked 3. Press the other side to lock the remaining two clips as shown on fig 2.a. and 2.b. 4. Module in place on PCB fig 3.a. and 3.b Tyco Electronics does not recommend the use of its products for other applications. Especially it is not recommended to use the modules in life support applications where such use may directly threaten life or injure due to device failure or malfunction. We reserve the right to make changes of the product at any time without notice, in order to supply the best possible product. Copyright by Vincotech Tyco Electronics Finsinger Feld 1, D-85521 Ottobrunn Revision:1 power.switches@tycoelectronics.com