F-219 (R) EQCD-040-04.00-TTL-STR-2 (0.50 mm) .0197"(HQCD) (0.80 mm) .0315"(EQCD) Q STRIP COAX CABLE ASSEMBLIES (R) SPECIFICATIONS HQCD Mates with: QTH, QSH For complete specifications see www.samtec.com?HQCD or www.samtec.com?EQCD EQCD Mates with: QTE, QSE Cable: 38 AWG micro coax ribbon Signal Routing: 50 W Single-Ended Overall Length: (95.3 mm) 03.75" to (1 m) 40" standard Cable Flexing Life: >10,000 cycles Cable Bending Radius: <2.5mm Plating: Au over 50 " (1.27 m) Ni Current Rating: EQCD: 500 mA per pin HQCD: 300 mA per pin (6 adjacent pins powered) Cable Propagation Delay: 4.79 nsec/meter Operating Temp Range: -25 C to +105 C Unmating Force (-RT1 option): -RT1 option increases unmating force up to 50% RoHS Compliant: Yes 0.50 mm or 0.80 mm pitch 38 AWG micro coax ribbon cable * Screw & panel mount options * Retention pins Socket or Terminal HIGH-SPEED CHANNEL PERFORMANCE HQCD or EQCD Rating based on Samtec reference channel. For full SI performance data visit Samtec.com or contact SIG@samtec.com TYPE 14 Surface Mount or Panel Mount G b p s NO. OF POSITIONS PER ROW WIRE LENGTH RECOGNITIONS For complete scope of recognitions see www.samtec.com/quality HQCD = (0.50 mm) .0197" pitch FILE NO. E111594 EQCD APPLICATIONS -030, -060, -090 (HQCD Series) -020, -040, -060 -"XX.XX" = Wire Length in Inches (43.7 mm) 01.72" minimum (EQCD Series) = (0.80 mm) .0315" pitch (9.28) .365 OAL = Wire Length + (24.13) .950 Processing conditions will affect mated height. Wire Length (1.27) .050 ALSO AVAILABLE (MOV Required) * * * * Other sizes and lengths Other terminations Other wire AWG Retention pin Notes: Cable lengths longer than 40.00" (1 meter) are not supported with S.I. test data. END NO. 1 (-STL SHOWN) END NO. 2 (-STR SHOWN) Design your High-Speed Cable with Samtec's High-Speed Cable Solutionator(R) at www.samtec.com/hdr This Series is non-standard, non-returnable. Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM All parts within this catalog are built to Samtec's specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply. EQCD-020-40.00-TPU-TTR-1 HQCD-030-06.00-STL-TTR-1-B HQCD, EQCD SERIES SCREW MOUNT APPLICATIONS (-F, -S, -B) #4-40 Thread Screw Down options Panel Mount options SO-0318-04-01-02 END NO. 1 END NO. 2 Specify END ASSEMBLIES from chart WIRING OPTION END OPTIONS -1 Leave blank for no Screw Mount & Retention End Option = Pin 1 to Pin 1 -2 = Pin 1 to Pin 2 -3 PANEL MOUNT END OPTION APPLICATIONS = Pin 1 to Second to Last Pin -4 = Pin 1 to Last Pin (-TPU, -TPD, -SPU, SPD) END 1 or END 2 END 1 ONLY PANEL MOUNT SURFACE MOUNT TTR Terminal, Top Mount, Notch Right TTL Terminal, Top Mount, Notch Left TBR Terminal, Bottom Mount, Notch Right TBL Terminal, Bottom Mount, Notch Left TPU Terminal, Panel Mount, Notch Up STR Socket, Top Mount, Notch Right TPD Terminal, Panel Mount, Notch Down STL Socket, Top Mount, Notch Left SPU Socket, Panel Mount, Notch Up SBR Socket, Bottom Mount, Notch Right SPD Socket, Panel Mount, Notch Down SBL Socket, Bottom Mount, Notch Left -F = Screw Mount End No. 1 only (Not available with XPX options) -S = Screw Mount End No. 2 only -B = Screw Mount Both Ends (Not available with XPX options) -1 = End No. 1 Screw Mount. End No. 2 Retention Pin or Socket Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM -2 = End No. 1 Retention Pin or Socket. End No. 2 Screw Mount Option All parts within this catalog are built to Samtec's specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.