2N4403 / MMBT4403
Symbol Parameter Value Units
VCEO Collec tor-Em i tter Voltage 40 V
VCBOCollector-Base Voltage40V
VEBO Emi tter-Base Voltage 5.0 V
ICCollector Current - Continuous600mA
TJ, Tstg Operating and Storage Junction Temperature Range -55 to +150 °C
PNP General Purpose Amplifier
This device is designed for use as a general purpose amplifier
and switch requiring collector currents to 500 mA.
Absolute Maximum Ratings* TA = 25°C unless otherwise noted
*These ratings are limiting values above which the serviceability of any semiconductor device may be impaired.
NOTES:
1) These ratings are based on a maximum junction temperature of 150 degrees C.
2) These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations.
2N4403
CBETO-92
MMBT4403
C
B
E
SOT-23
Mark: 2T
Thermal Characteristics TA = 25°C unless otherwise noted
Symbol Characteristic Max Units
2N4403 *MMBT4403
PDTotal Device Dissipation
Derate above 25°C625
5.0 350
2.8 mW
mW/°C
RθJC Thermal Res i stance, Junction t o Case 83.3 °C/W
RθJA Thermal Res i stance, Junction t o Ambient 200 357 °C/W
*Device mounted on FR-4 PCB 1.6" X 1.6" X 0.06."
2001 Fairchild Semiconductor Corporation
2N4403/MMBT4403, Rev A
2N4403 / MMBT4403
Electrical Characteristics TA = 25°C unless otherwise noted
OFF CHARACTERISTICS
ON CHARACTERISTICS
SMALL SIGNAL CHARACTERISTICS
SWITCHING CHARACTERISTICS
tdDelay Time VCC = 30 V, I C = 150 mA, 15 ns
trRise Time IB1 = 15 m A 20 ns
tsStorage Time VCC = 6.0 V, I C = 150 mA 225 ns
tfFall Time IB1 = IB2 = 15 m A 30 ns
*Pulse Test: Pulse Width £ 300 ms, Duty Cycle £ 2.0%
Symbol Parameter Test Conditions Min Max Units
V(BR)CEO Coll ector-Emitt er Breakdown
Voltage* IC = 1.0 mA, IB = 040V
V(BR)CBOCollector-Base Breakdown VoltageIC = 0.1 mA, IE = 040V
V(BR)EBO Emitter-Base Breakdown Voltage IE = 0.1 A, I C = 0 5.0 V
IBEX Base Cutoff Current VCE = 35 V, VEB = 0. 4 V 0.1 µA
ICEX Collector Cutoff Current VCE = 35 V, V BE = 0.4 V 0.1 µA
hFE DC Current Gain IC = 0.1 mA, VCE = 1.0 V
IC = 1.0 mA , VCE = 1.0 V
IC = 10 mA, V CE = 1.0 V
IC = 150 mA, V CE = 2.0 V*
IC = 500 mA, V CE = 2.0 V*
30
60
100
100
20 300
VCE(sat)Collec tor-Em i tter Sat uration
Voltage* IC = 150 mA, IB = 15 mA
IC = 500 mA, I B = 50 mA 0.4
0.75 V
V
VBE(sat)Base-Emitter Saturation Voltage IC = 150 mA, I B = 15 mA*
IC = 500 mA, I B = 50 mA 0.75 0.95
1.3 V
V
PNP General Purpose Amplifier
(continued)
fTCurrent Gain - Bandwidth P roduct IC = 20 mA , VCE = 10 V,
f = 100 MHz 200 MHz
Ccb Collector-B ase Capacitance VCB = 10 V, I E = 0,
f = 140 kHz 8.5 pF
Ceb Emi t ter-Base Capaci tance VBE = 0.5 V, I C = 0,
f = 140 kHz 30 pF
hie Input Impedance IC = 1.0 mA, VCE = 10 V,
f = 1.0 kHz 1.5 15 kΩ
hre Voltage Feedbac k Ratio IC = 1.0 mA, VCE = 10 V,
f = 1.0 kHz 0.1 8.0 x 10-4
hfe Smal l -S i gnal Current Gain IC = 1.0 mA , V CE = 10 V,
f = 1.0 kHz 60 500
hoe Output Admitt ance IC = 1.0 mA, VCE = 10 V ,
f = 1.0 kHz 1.0 100 µmhos
Typical Characteristics
Typical Pulsed Current Gain
vs Collector Current
0.1 0.3 1 3 10 30 100 300
0
100
200
300
400
500
I - COLLECTOR CURRENT (mA)
h - TYPICA L PULSED CURRENT GAIN
C
FE
125 °C
25 °C
- 4 0 ° C
V = 5 V
CE
Input and Output Capacitance
vs Reverse Bias Voltage
0.1 1 10 50
0
4
8
12
16
20
REVERSE BIAS VOLTAGE (V)
CAP ACIT ANCE (pF)
Cob
C
ib
C o llector -C u toff Cu r rent
vs A mb ient Temperatu re
25 50 75 100 125
0.01
0.1
1
10
100
T - AMBIE NT TEMP E RATURE ( C)
I - C OLLECTOR CURR EN T (nA)
A
CBO
°
V = 35V
CB
C o ll ecto r -Emitter Satur ati o n
Vo ltag e vs Collector Cur rent
110100500
0
0.1
0.2
0.3
0.4
0.5
I - COLLECTO R C UR RENT (m A)
V - COLLEC TOR EMITTER VOLTA GE (V)
C
CESAT
β= 10
25 °C
- 40 °C
125 °C
B ase-Emitter Satur ati o n
Vo ltag e vs C o llector Cu rrent
110100500
0
0.2
0.4
0.6
0.8
1
I - COLLEC TOR CUR RE NT (mA)
V - BA SE EMITTER VOLTAGE (V)
C
BESAT
25 °C
- 40 °C
125 °C
β= 10
Base Emitter ON Vol tage vs
C o ll ector Cu r rent
0.1 1 10 25
0
0.2
0.4
0.6
0.8
1
I - COLLEC TOR CURRENT (mA)
V - B ASE EMITTER ON VOLTAGE (V)
C
BE( ON)
V = 5V
CE
25 °C
- 40 °C
125°C
PNP General Purpose Amplifier
(continued)
2N4403 / MMBT4403
Typical Characteristics (continued)
S wit c hing Tim es
vs Collector Curren t
10 100 1000
0
50
100
150
200
250
I - COLL ECTOR CU RRENT (mA)
TIME ( nS)
I = I =
tr
t
s
B1
C
B2 Ic
10
V = 15 V
cc
tf
td
Tu r n On and Turn O f f Times
vs Col lector C urre nt
10 100 1000
0
100
200
300
400
500
I - COLLECTO R CURRENT (m A)
TIME ( nS)
I = I =
ton
t
off
B1
C
B2 Ic
10
V = 15 V
cc
Po we r Dissipat ion vs
Am bient Temperature
0 25 50 75 100 125 150
0
0.25
0.5
0.75
1
TEMPERATUR E ( C)
P - POWER DISSIPATION (W)
D
o
SOT-223
TO-92
SOT-23
Ri se Time vs Coll ect or
and Turn On Base Currents
10 100 500
1
2
5
10
20
50
I - COLLECTOR CURRENT (mA)
I - TU RN 0 N BASE CURRENT (mA)
30 ns
C
t = 15 V
r
B1
60 ns
PNP General Purpose Amplifier
(continued)
2N4403 / MMBT4403
Typical Common Emitter Characteristics (f = 1.0kHz)
Common Emitte r Characteri st ics
12 51020 50
0.1
0.2
0.5
1
2
5
I - CO L L ECTOR CURR EN T ( mA)
CHAR. RELATIVE TO VAL UES AT I = - 10mA
V = -10 V
CE
C
C
T = 25 C
A o
hoe
h re
hfe
hie
_ _ _ _ _ _
Commo n Emitte r Charact eri s t ics
-20-16-12-8-4
0.8
0.9
1
1.1
1.2
1.3
V - COLL ECTOR VOLTA GE ( V)
CHAR. RELATIVE TO VALUES AT V = -10V
I = -10 mA
C
CE
CE
T = 25 C
A o
hoe
h an d h
re
hfe
hie
oe hfe
hie
h re
Commo n Emitter Characte ri st ics
-40-200 20406080100
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
T - AMBIENT TEMP ERATU RE ( C)
CHAR. RE LATIVE TO VALUES AT T = 25 C
V = -10 V
CE
A
A
hoe
h re
hfe
hie
o
o
I = -10 mA
C hfe
hie
h re
hoe
PNP General Purpose Amplifier
(continued)
2N4403 / MMBT4403
Test Circuits
FIGURE 1: Saturated Turn-On Switching Time Test Circuit
FIGURE 2: Saturated T urn-Off Switching T ime T est Circuit
1.0 KΩΩ
ΩΩ
Ω
- 6.0 V
1.5 V
1.0 KΩΩ
ΩΩ
Ω
- 30 V
0
≤≤
≤≤
≤ 200ns
≤≤
≤≤
≤ 200ns
- 16 V
0
50 ΩΩ
ΩΩ
Ω
200 ΩΩ
ΩΩ
Ω
1 KΩΩ
ΩΩ
Ω37 ΩΩ
ΩΩ
Ω
50 ΩΩ
ΩΩ
Ω
- 30 V
NOTE: BVEBO = 5.0 V
PNP General Purpose Amplifier
(continued)
2N4403 / MMBT4403
TO-92 Tape and Reel Data
March 2001, Rev. B1
©2001 Fairchild Semiconductor Corporation
TO-92 Packaging
Configuration: Figure 1.0
AMMO PACK OPTION
See Fig 3.0 for 2 Ammo
Pack Options
2000 units per
EO70 box for
std option
FSCINT Label
530mm x 130m m x
83mm
Inter med iate box
10,000 units maximum
per
intermediate box
for std option
FSCINT Label
114mm x 102m m x 51mm
Immed iate Box
Anti-static
Bubble Sheets
(TO-92) BULK PACKING INFORMATION
EOL
CODE DESCRIPTION LEADCLIP
DIMENSION QUANTITY
J18Z TO-18 OPTION STD NO LEAD CLIP 2.0 K / BOX
J05Z TO-5 OPTION STD NO LEAD CLIP 1.5 K / BOX
NO EOL
CODE TO-92 STANDARD
STRAIGHT FOR: PKG 92, NO LEADCLIP 2.0 K / BOX
BULK OPTION
See Bulk Packing
Information tabl e
375mm x 267m m x 375mm
Inter med iate Box
FSCINT
Label
Customized
Label
333mm x 231m m x 183mm
Inter med iate Box
FSCINT
Label
Customized
Label
TO-92 TNR/AMMO PACKING INFROMATION
Packing Style Qu antity EO L code
Reel A 2,000 D26Z
E2,000 D27Z
Ammo M 2,000 D74Z
P2,000 D75Z
U nit weight = 0.22 g m
Reel weight with com pon e nts = 1 .0 4 kg
Ammo weight with comp one n ts = 1.02 kg
Max quantity p er inte rmediate box = 10,000 units
F63TNR
Label
5 Ammo boxes per
Inter med iate Box
Customized
Label
327mm x 158m m x 135mm
Immed iate Box
LOT:
CBVK741B019
NSID:
PN2222N
D/C1:
D9842
SPEC REV:
B2
SPEC:
QTY:
10000
QA REV:
FAIRCHILD SEMICONDUCTOR CORPORATION
HTB:B
(FSCINT)
F63TNR
Label
Customized
Label
5 Reels per
Inter med iate Box
TAPE and REEL OPTION
See Fig 2.0 for various
Reeling Styles
LOT: CBVK74 1B019
FS ID: PN 2 22N
D/C1: D9842 QTY1: SPEC REV:
SPEC:
QTY: 2000
D/C2: QTY2: CPN: N/F: F (F6 3TNR) 3
F63TNR Label sample
FSCINT Label sample
C
5 EO70 boxes per
intermediate Box
ustomized
Label
94 (NON PROELECTRON
SERIES), 96
L34Z TO-92 STANDARD
STRAIGHT FOR: PKG 94 NO LEADCLIP 2.0 K / BOX
(PROELECTRON SERIES
BCXXX, BFXXX, BSRXXX),
97, 98
TO-92 Tape and Reel Data, continued
September 1999, Rev. B
TO-92 Reeling Style
Configuration: Figure 2.0
Style “A”, D26Z, D70 Z (s/h)
Machine Op tion “A” (H)
Style “E ”, D2 7Z, D 71Z (s/ h)
Machine O ption “E” (J)
FIRST WIRE OFF IS EMITTER
ADHESIVE TAPE IS ON THE TOP SIDE
FLAT OF TRANSISTOR IS ON BOTTOM
ORDER STYLE
D75Z (P)
FIRST WIRE OFF IS COLLECTOR
ADHESIVE TAPE IS ON THE TOP SIDE
FLAT OF TRANSISTOR IS ON TOP
ORDER STYLE
D74Z (M)
TO-92 Radial Ammo Packa ging
Configuration: Figure 3.0
FIRST WIRE OFF IS EMITTER (ON PKG. 92)
ADHESIVE TAPE IS ON BOTTOM SIDE
FLAT OF TRANSISTOR IS ON BOTTOM
FIRST WIRE OFF IS COLLECTOR (ON PKG. 92)
ADHESIVE TAPE IS ON BOTTOM SIDE
FLAT OF TRANSISTOR IS ON TOP
ITEM DESCRIPTION
Base of Package to Lead Bend
Com p on en t Heig ht
Lead Clinch Heig ht
Com p on en t Ba s e He ig ht
Com p on en t Al ig nm e nt ( sid e/s id e )
Com p on en t Al ig nm e nt ( front/bac k )
Com p on en t Pitc h
Feed Hole Pitch
Hole Center to First Lead
Hole Center to Component Center
Lead S prea d
Lead Thick ness
Cut Lead Length
Taped Lead Lengt h
Taped Lead Thickness
Carrier Tape Thickness
Carrier Tape Width
Hold - down Tape Width
Hold - down Tape position
Feed Hole Position
Sprocket Hole Diameter
Lead S pri ng Out
SYMBOL
b
Ha
HO
H1
Pd
Hd
P
PO
P1
P2
F1/F2
d
L
L1
t
t1
W
WO
W1
W2
DO
S
DIMENSION
0. 09 8 (m ax )
0. 92 8 (+ /- 0.025)
0. 63 0 (+ /- 0.020)
0. 74 8 (+ /- 0.020)
0. 04 0 (m ax )
0. 03 1 (m ax )
0. 50 0 (+ /- 0.020)
0. 50 0 (+ /- 0.008)
0. 15 0 (+ 0 .00 9, -0 .0 10)
0. 24 7 (+ /- 0.007)
0. 10 4 (+ /- 0 . 01 0)
0. 01 8 (+ 0 .00 2, -0 .0 03)
0. 42 9 (m ax )
0. 20 9 (+ 0 .05 1, -0 .0 52)
0. 03 2 (+ /- 0.006)
0. 02 1 (+ /- 0.006)
0. 70 8 (+ 0 .02 0, -0 .0 19)
0. 23 6 (+ /- 0.012)
0. 03 5 (m ax )
0. 36 0 (+ /- 0.025)
0. 15 7 (+ 0 .00 8, -0 .0 07)
0. 00 4 (m ax )
Note : All dimensions ar e in inches.
ITEM DESCRIPTION SYSMBOL MINIMUM MAXIMUM
Ree l Di am e ter D1 13. 9 75 14. 02 5
Arb or Hol e Di am et er (S ta nd ard) D2 1.16 0 1.2 00
(Small Hole) D2 0.650 0.700
Core Diameter D3 3.100 3.300
Hub Recess Inner Diameter D4 2.700 3.100
Hub Recess Depth W1 0.370 0.570
Flange to Flange Inner Width W2 1.6 30 1.690
Hub to Hub Center Widt h W3 2.090
Note: All dimensions are inches
TO-92 Tape and Reel Taping
Dimension Configuration: Figure 4.0
Ha
H1 HO
PO
P2
P1 F1
DO
P Pd
b
d
L1
LS
WO W2
W
t
t1
Hd
W1
TO-92 Reel
Configuration: Figure 5.0
User D ire c tion of Feed
SENS ITIVE DEVICES
ELECTROSTATIC
D1
D3
Customized Label
W2
W1 W3
F63 TN R Label
D4
D2
TO-92 Tape and Reel Data, continued
July 1999, Rev. A
TO-92 (FS PKG Code 92, 94, 96)
TO-92 Package Dimensions
January 2000, Rev. B
1:1
Scale 1:1 on letter size paper
Dimensions shown below are in:
inches [millimeters]
Part Weight per unit (gram): 0.1977
©2000 Fairchild Semiconductor International
SOT-23 Packag in g
Configurat ion: Figure 1.0
Components Leader Tape
500mm minimum or
125 emp ty pocket s
Tr ailer Tape
300mm minimum or
75 empty pocket s
SOT-23 Tape Leader and Trailer
Configuration: Figure 2.0
Cover Tape
Carrier Tape
Note/Comments
Packaging Option
SOT-23 Packaging Information
Standard
(no flow code) D87Z
Packaging type
Reel Si ze
TNR
7" Dia
TNR
13"
Qty per Reel/Tube/Bag 3,000 10,000
Bo x Dim ensi on (m m) 187x107x183 343x343x64
Max qt y per B o x 24,000 30,000
Weight per unit (gm) 0.0082 0.0082
Weight per Reel (kg) 0.1175 0.4006
Human readable
Label
Human Readable Label
Human Readable Label sample
343mm x 342mm x 64mm
Intermediate box for L87Z Opti on
187mm x 107mm x 183mm
Intermediate Box for St andard Op tion
SOT-23 Unit Orientation
3P 3P 3P 3P
Human Readable
Label
Customized Label
Embossed
Carrier Tape
Antistatic Cover Tape
Packaging Description:
SOT-23
made from a dissipative (carbon filled) polycarbonate
resin. The cover tape is a multilayer film (Heat Acti vated
Adhesive in nature) primarily composed of polyester film,
adhesive layer, sealant, and anti-static sprayed agent.
These reeled parts in standard option are shipped with
3,000 uni ts per 7" or 177cm di ameter reel. The reels are
dark blue in color and is made of polystyrene plastic (anti-
static coated). Other option comes in 10,000 units per 13"
or 330cm diameter reel. T hi s and some other opt i ons are
described in the Packaging Informati on table.
These full reels are individually labeled and pl aced insi de
a standard intermediate made of recyclable corrugated
brown paper wi th a Fai rchil d l ogo pri nt i ng. One pizza box
contains eight reels maximum. And these intermediate
boxes are placed inside a labeled shipping box which
comes i n different sizes depending on the number of parts
shipped.
parts are shipped in tape. The carrier tape is
SOT-23 Tape and Reel Data
September 1999, Rev . C
©2000 Fairchild Semiconductor International
Dimensions are in millimeter
Pkg type
A0 B0 W D0 D1 E1 E2 F P1 P0 K0 T Wc Tc
SOT-23
(8mm)
3.15
+/-0.10 2.77
+/-0.10 8.0
+/-0.3 1.55
+/-0.05 1.125
+/-0.125 1.75
+/-0.10 6.25
min 3.50
+/-0.05 4.0
+/-0.1 4.0
+/-0.1 1.30
+/-0.10 0.228
+/-0.013 5.2
+/-0.3 0.06
+/-0.02
Dimensions are in inches and millimeters
Tape Size Reel
Option Dim A Dim B Dim C Dim D Dim N Dim W1 Dim W2 Dim W3 (LSL-USL)
8mm 7" Dia 7.00
177.8 0.059
1.5 512 +0. 020/-0.008
13 +0.5/-0.2 0.795
20.2 2.165
55 0.331 +0.059/-0.000
8.4 +1.5/0 0.567
14.4 0.311 – 0.429
7.9 – 10.9
8m m 13" Dia 13.00
330 0.059
1.5 512 +0. 020/-0.008
13 +0.5/-0.2 0.795
20.2 4.00
100 0.331 +0.059/-0.000
8.4 +1.5/0 0.567
14.4 0.311 – 0.429
7.9 – 10.9
See detail AA
Dim A
max
13" Diameter Option
7" Diameter Opti on
Dim A
Max
See detail AA
W3
W2 max Measured at Hub
W1 Measured at Hub
Dim N
Dim D
min
Dim C
B Min
DETAIL AA
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481
rotational and lateral movement requirements (see sketches A, B, and C).
20 deg maximum component rotation
0.5mm
maximum
0.5mm
maximum
Sketch C (Top View)
Component lateral movement
Typical
component
cavity
center line
20 deg maximum
Typical
component
center line
B0
A0
Sketch B (Top View)
Component Rotation
Sketch A (Side or Front Sectional View)
Component Rotation
User Direction of Feed
SOT-23 Embossed Carrier Tape
Configuration: Figure 3.0
SOT-23 Reel Configuration: Figure 4.0
P1 A0
D1
FW
E1
E2
Tc
Wc
K0
T
B0
D0P0 P2
SOT-23 Tape and Reel Data, continued
September 1999, Rev . C
SOT-23 (FS PKG Code 49)
SOT-23 Package Dimensions
September 1998, Rev . A1
1:1
Scale 1:1 on letter size paper
Dimensions shown below are in:
inches [millimeters]
Par t Weight per unit (gram): 0.0082
©2000 Fairchild Semiconductor International
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is
not intended to be an exhaustive list of all such trademarks.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROV AL OF FAIRCHILD SEMICONDUCTOR CORPORA TION.
As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, or (c) whose
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
reasonably expected to result in significant injury to the
user.
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
PRODUCT ST A TUS DEFINITIONS
Definition of Terms
Datasheet Identification Product Status Definition
Advance Information
Preliminary
No Identification Needed
Obsolete
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Formative or
In Design
First Production
Full Production
Not In Production
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.
PowerTrench
QFET™
QS™
QT Optoelectronics™
Quiet Series™
SILENT SWITCHER
SMART START™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
FASTr™
GlobalOptoisolator™
GTO™
HiSeC™
ISOPLANAR™
MICROWIRE™
OPTOLOGIC™
OPTOPLANAR™
PACMAN™
POP™
Rev . G
ACEx™
Bottomless™
CoolFET™
CROSSVOLT™
DOME™
E2CMOSTM
EnSignaTM
FACT™
F ACT Quiet Series™
FAST
SyncFET™
TinyLogic™
UHC™
VCX™
