TD3063 Zero-Volt Switching Triac Driver DESCRIPTION The TD3063 consists of a single input LED optically coupled to a zero-volt crossing triac driver. The TD3063 provides high input-to-output isolation and is designed to drive high-powered triacs. Typical uses include interfacing logic level control signals to equipment powered from 110Vac and 220Vac lines. FEATURES APPLICATIONS x Zero-volt switching x Home appliances x 600V blocking voltage x Motor control x High input-to-output isolation x Solid state relays x High reliability x Valve control x 5mA turn-on current x Solenoids x Exercise equipment OPTIONS/SUFFIXES x -H High Output Isolation x -S Surface Mount Option x -TR Tape and Reel MAXIMUM RATINGS PARAMETER UNIT MIN Storage Temperature C -55 125 Operating Temperature C -40 85 Continuous Input Current mA 40 +/- AC Output Transient Input Current mA 400 Reverse Input Control Voltage V Do Not Use SCHEMATIC DIAGRAM + Input - Input 1 6 2 5 Output Power Dissipation 3 4 mW TYP MAX 6 500 -/+ AC Output APPROVALS x rev 1.0 UL Approved File # E201932 Solid State Optronics, Inc. 1.888.377.4776 www.ssousa.com TD3063 Zero-Volt Switching Triac Driver ELECTRICAL CHARACTERISTICS - 25 PARAMETER UNIT MIN TYP MAX 1.2 1.5 TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V LED Reverse Voltage Turn-On Current Turn-Off Current mA If = 10mA V 6 12 Ir = 10uA mA 5 2.5 Io = 100mA 0.5 OUTPUT SPECIFICATIONS Blocking Voltage V Continuous Load Current mA Holding Current PA Leakage Current PA On-State Voltage V Critical Rate of Rise V/ 600 Io = 1uA 100 Iin = 5mA 1 Vo = 600V 3 Iin = 5mA 250 2 Ps 1000 1500 COUPLED SPECIFICATIONS Isolation Voltage -H Suffix Coupled Capacitance rev 1.0 V 2500 V 3750 pF T = 1 minute T = 1 minute 2 Solid State Optronics, Inc. 1.888.377.4776 www.ssousa.com TD3063 Zero-Volt Switching Triac Driver PERFORMANCE DATA TD3063 TD3063 Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25C 50 120 100 80 60 40 20 0 Device Count Load Current (mA) Typical Load Current vs. Temperature -40 -20 0 20 40 60 40 30 20 10 0 590 600 610 620 630 640 650 660 80 Blocking Voltage (V) Tem perature (C) ZERO-VOLT SWITCHING This solid state relay has been designed with a driver circuit that controls the operation of two back-to-back silicon controlled rectifiers (SCRs), each responsible for one half of the AC cycle. If an AC signal is examined, the turn on, turn off and zero-volt switching can be seen. Figure 1 shows a typical 60 Hz, 120Vac signal with a corresponding relay input signal: 5 Relay Input Signal is Turned On. 1 Relay Input Signal is Turned Off. Input Signal 2 SCR #1 Turns On when 5V threshold is reached. 6 SCR #1 and Relay Turn Off at Zero Volts. 5V Threshold 3 4 SCR #1 Turns Off, SCR #2 Turns On at Zero Volts. SCR #2 Turns Off, SCR #1 Turns On at Zero Volts. Figure 1 shows the sequence of zero-volt switching operation. At Stage 1, an input signal is applied to the relay. The relay will not turn on until the threshold voltage of 5V is reached. Once this point is reached (Stage 2), SCR #1 (designated as the SCR which controls positive AC voltage) turns on. However, SCR #1 only conducts for an instant, as the cycle quickly crosses zero. At this point (Stage 3), SCR #1 will turn off and SCR #2 (negative AC voltage) turns on. Likewise, at the next zero cross (Stage 4), SCR #2 will turn off and SCR #1 conducts again. Even though the input signal is terminated at Stage 5, the relay will continue to conduct (typical SCR behavior) until Stage 6, when SCR #1 crosses zero and ceases to conduct. Please note that turn on can likewise begin on the negative phase of the AC cycle with a -5V threshold, though only the positive phase is shown here. rev 1.0 Solid State Optronics, Inc. 1.888.377.4776 www.ssousa.com TD3063 Zero-Volt Switching Triac Driver MECHANICAL DIMENSIONS 6 PIN DUAL IN-LINE PACKAGE 6 PIN SURFACE MOUNT DEVICE TOLERANCE :+ 0.25mm Meeting VDE Requirements (Clearance and Creepage) -V Unit (mm) rev 1.0 Solid State Optronics, Inc. 1.888.377.4776 www.ssousa.com