AA-3021SGS - KINGBRIGHT CORPORATION

SPEC NO: DSAL0109 REV NO: V.6B DATE: OCT/11/2013 PAGE: 1 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201006489

3.0x2.0mm SURFACE MOUNT LED LAMP

Part Number: AA3021SGS

Super Bright Green

Features

z3.0mm x 2.0mm, 1.3mm high, only minimum space

required.

zSuitable for compact optoelectronic applications.

zLow power consumption.

zPackage : 2000pcs / reel.

zMoisture sensitivity level : level 3.

zRoHS compliant.

Description

The Super Bright Green source color devices are made with

Gallium Phosphide Green Light Emitting Diode.

Package Dimensions

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.2(0.008") unless otherwise noted.

3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.

4. The device has a single mounting surface. The device must be mounted according to the specifications.

SPEC NO: DSAL0109 REV NO: V.6B DATE: OCT/11/2013 PAGE: 2 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201006489

1. Handle the component along the side surfaces by using forceps or appropriate tools.

2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.

3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or

damage the internal circuitry.

4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.

4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.

4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup

and avoid damage during production.

5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of

leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.

Handling Precautions

Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic

significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.

As a result, special handling precautions need to be observed during assembly using silicone encapsulated

LED products. Failure to comply might lead to damage and premature failure of the LED.

SPEC NO: DSAL0109 REV NO: V.6B DATE: OCT/11/2013 PAGE: 3 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201006489

Selection Guide

Notes:

1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.

2. Luminous intensity/ luminous Flux: +/-15%.

3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.

Absolute Maximum Ratings at TA=25°C

Electrical / Optical Characteristics at TA=25°C

Notes:

1.Wavelength: +/-1nm.

2. Forward Voltage: +/-0.1V.

3. Wavelength value is traceable to the CIE127-2007 compliant national standards.

Note:

1. 1/10 Duty Cycle, 0.1ms Pulse Width.

Part No. Dice Lens Type

V

iewing

Angle [1]

Min. Typ. 2θ1/2

AA3021SGS Super Bright Green (GaP) Water Clear 12 20 125°

Iv (mcd) [2]

@ 20mA

Symbol Parameter Device Typ. Max. Units Test Conditions

λpeak Peak Wavelength Super Bright Green 565 nm IF=20mA

λD [1] Dominant Wavelength Super Bright Green 568 nm IF=20mA

Δλ1/2 Spectral Line Half-width Super Bright Green 30 nm IF=20mA

C Capacitance Super Bright Green 15 pF VF=0V;f=1MHz

VF [2] Forward Voltage Super Bright Green 2.2 2.5 V IF=20mA

IR Reverse Current Super Bright Green 10 uA VR=5V

Parameter Super Bright Green Units

Power dissipation 62.5 mW

DC Forward Current 25 mA

Peak Forward Current [1] 140 mA

Reverse Voltage 5 V

Operating Temperature -40°C To +85°C

Storage Temperature -40°C To +85°C

SPEC NO: DSAL0109 REV NO: V.6B DATE: OCT/11/2013 PAGE: 4 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201006489

Super Bright Green AA3021SGS

SPEC NO: DSAL0109 REV NO: V.6B DATE: OCT/11/2013 PAGE: 5 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201006489

AA3021SGS

Reflow soldering is recommended and the soldering profile is shown below.

Other soldering methods are not recommended as they might cause damage to the product.

Recommended Soldering Pattern

(Units : mm; Tolerance: ± 0.1)

Reel Dimension

Tape Dimensions

(Units : mm)

SPEC NO: DSAL0109 REV NO: V.6B DATE: OCT/11/2013 PAGE: 6 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1201006489

PACKING & LABEL SPECIFICATIONS AA3021SGS

Terms and conditions for the usage of this document

1.The information included in this document reflects representative usage scenarios and is intended

for technical reference only.

2.The part number, type, and specifications mentioned in this document are subject to future change

and improvement without notice. Before production usage customer should refer to the latest

datasheet for the updated specifications.

3.When using the products referenced in this document, please make sure the product is being

operated within the environmental and electrical limits specified in the datasheet. If customer usage

exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.

4.The information in this document applies to typical usage in consumer electronics applications.

If customer's application has special reliability requirements or have life-threatening liabilities,

such as automotive or medical usage, please consult with Kingbright representative for further

assistance.

5.The contents and information of this document may not be reproduced or re-transmitted without

permission by Kingbright.

6.All design applications should refer to Kingbright application notes available at

http://www.KingbrightUSA.com/ApplicationNotes