© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/28/19
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Glass Passivated Junctions for Greater Parameter
Uniformity and Stability
Small, Rugged, Thermowatt Construction for Low Thermal
Resistance, High Heat Dissipation and Durability
• Blocking Voltage to 800 Volts
• 300 A Surge Current Capability
Pb−Free Package is Available
Features
Designed primarily for half-wave ac control applications,
such as motor controls, heating controls and power supply
crowbar circuits.
Description
2N6504 Series
Functional Diagram
Pb
Additional Information
Samples
Resources
Datasheet
Pin Out
CASE 221A
STYLE 4
12
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/28/19
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Rating Symbol Value Unit
Peak Repetitive Off-State Voltage (Note 1)
(Gate Open, Sine Wave 50 to 60 Hz, TJ = 25 to 125°C)
2N6504
2N6505
2N6507
2N6508
2N6509
VDRM,
VRRM
50
100
400
600
800
V
On-State RMS Current (180° Conduction Angles; TC = 85°C) IT (RMS) 25 A
Average On-State Current (180° Conduction Angles; TC = 85°C) IT (AV) 16 A
Peak Non-repetitive Surge Current
(1/2 Cycle, Sine Wave 60 Hz, TJ = 100°C) ITSM 250 A²s
Forward Peak Gate Power (Pulse Width ≤ 1.0 µs, TC = 85°C) PGM 20 W
Forward Average Gate Power (t = 8.3 ms, TC = 85°C) PG(AV) 0.5 W
Forward Peak Gate Current (Pulse Width ≤ 1.0 µs, TC = 85°C) IGM 2.0 A
Operating Junction Temperature Range TJ-40 to +125 °C
Storage Temperature Range Tstg -40 to +125 °C
Maximum Ratings (TJ = 25°C unless otherwise noted)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
1. V DRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative
potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
Thermal Characteristics
Rating Symbol Value Unit
*Thermal Resistance, Junction to Case RƟJC 1.5 °C/W
*Maximum Lead Temperature for Soldering Purposes, 1/8” from case for
10 seconds TL260 °C
* Indicates JEDEC Registered Data.
Electrical Characteristics - OFF (TC = 25°C unless otherwise noted)
Characteristic Symbol Min Ty p Max Unit
†Peak Repetitive Blocking Current
(VAK = VDRM = VRRM; Gate Open) TJ = 25°C
TJ = 125°C
IDRM,
IRRM
- - 1.0 µA
- - 2.0 mA
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/28/19
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Electrical Characteristics - ON (TC = 25°C unless otherwise noted; Electricals apply in both directions)
*Indicates JEDEC Registered Data
2. Pulse Test: Pulse Width ≤ 300 µsec, Duty Cycle ≤ 2%.
Dynamic Characteristics
Characteristic Symbol Min Ty p Max Unit
Critical Rate of Rise of Off-State Voltage (Gate Open, Rated VDRM,
Exponential Waveform) dv/dt(c) 50 V/µs
Characteristic Symbol Min Ty p Max Unit
* Forward On-State Voltage (Note 2) (ITM = 50 A) VTM 1.8 V
* Gate Trigger Current (Continuous dc)
(VAK = Rated VDRM or VRRM, Gate Open) TC = 25°C
TC = -40°C IGT
9.0 30 mA
75
* Gate Trigger Voltage (Continuous dc) (VAK = 12 Vdc, RL = 100 Ω, TC = -40 °C) VGT 1.0 1.5 V
Gate Non-Trigger Voltage (VAK = 12 Vdc, RL = 100 Ω, TJ = 125°C) VGD 0.2 V
*Holding Current (VD = 12 Vdc,
Initiating Current = 200 mA, Gate Open) TC = 25°C
TC = -40°C IH
18 40 mA
80
* Turn-On Time (ITM = 25 A, IGT = 50 mAdc) tgt 1.5 2.0 µs
Turn-Off Time (VRM = rated voltage) (ITM = 25 A, IR = 25 A)
(ITM = 25 A, IR = 25 A, TJ = 125°C) tq
- - 15 µs
- - 35
Voltage Current Characteristic of SCR
Symbol Parameter
VDRM Peak Repetitive Forward Off State Voltage
IDRM Peak Forward Blocking Current
VRRM Peak Repetitive Reverse Off State Voltage
IRRM Peak Reverse Blocking Current
VTM Maximum On State Voltage
IHHolding Current
I
I
I
Figure 1. AverageCurrent Derating Figure 2. Maximum On-State Power Dissipation
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/28/19
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Figure 4. Maximum Non−Repetitive Surge CurrentFigure 3. Typical On−State Characteristics
Figure 5. Thermal Response
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/28/19
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Figure 6. Typical Gate Trigger Current vs. Junction Temperature
Typical Trigger Characteristics
Figure 7. Typical Gate Trigger Voltage vs. Junction Temperature
Figure 8. Typical Holding Current vs.Junction Temperature Ordering Information
Device Package Shipping
2N6504 TO-220AB
500 Units / Box
2N6504G TO-220AB
(Pb-Free)
2N6505 TO-220AB
2N6505G TO-220AB
(Pb-Free)
2N6505T TO-220AB
500 Units / Box
2N6505TG TO-220AB
(Pb-Free)
2N6507 TO-220AB
500 Units / Box
2N6507G TO-220AB
(Pb-Free)
2N6507T TO-220AB
500 Units / Box
2N6507TG TO-220AB
(Pb-Free)
2N6508 TO-220AB
500 Units / Box
2N6508G TO-220AB
(Pb-Free)
2N6508TG TO-220AB 500 Units / Box
2N6509 TO-220AB
(Pb-Free) 500 Units / Box
2N6509G TO-220AB
2N6509T TO-220AB
(Pb-Free) 500 Units / Box
2N6509TG TO-220AB
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/28/19
Thyristors
Surface Mount – 50 - 800V > 2N6504 Series
Dimensions Part Marking System
A
K
L
V
G
D
N
Z
H
Q
FB
12 3
4
SEATING
PLANE
S
R
J
U
TC
Pin Assignment
1 Cathode
2 Anode
3 Gate
4 Anode
TO-220AB
CASE 221A
STYLE 3
12
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each
product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at:
www.littelfuse.com/disclaimer-electronics.
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
Dim Inches Millimeters
Min Max Min Max
A 0.590 0.620 14.99 15.75
B 0.380 0.420 9.65 10.67
C 0.178 0.188 4.52 4.78
D 0.025 0.035 0.64 0.89
F 0.142 0.147 3.61 3.73
G 0.095 0.105 2.41 2.67
H0.110 0.130 2.79 3.30
J0.018 0.024 0.46 0.61
K 0.540 0.575 13.72 14.61
L 0.060 0.075 1.52 1.91
N 0.195 0.205 4.95 5.21
Q 0.105 0.115 2.67 2.92
R 0.085 0.095 2.16 2.41
S 0.045 0.060 1. 14 1.52
T 0.235 0.255 5.97 6.47
U 0.000 0.050 0.00 1.27
V 0.045 --- 1.15 ---
Z --- 0.080 --- 2.04