Q68100A1484 - OSRAM OPTO SEMICONDUCTORS

SCE574x

0.180’’ 4-Character 5x 7 Dot Matrix Serial Input

Dot Addressable Intelligent Dis p lay® Devices

SCE574xP-SIP SCE574xQ-SIP with right angle bends

2006-03-30 1

Lead (Pb) Free Product / RoHS Compliant

Standard Red SCE5740 Yellow SCE5741 Super-red SCE5742

Green SCE5743 High Efficiency Green SCE5744 Orange SCE5745

DESCRIPTION

The SCE574x is a four digit, dot addressab l e 5 x 7 dot

matrix, serial input, alphanumeric Intelligent Display

device. The four digits are packaged in a rugged, high

quality, opticall y transparent, plastic 14 pin DIP with

2.54 mm (0.1") pin spacing.

The SCE574xP is a SIP v ersion of SCE574x. The

SCE574xQ is also a SIP version of the SCE574x but the

leads are at right angles to the package so that the part

can be mounted vertically. The SIP version parts have

only 7 pins. The SIP parts do not hav e the option of using

an external clock. All the electrical descriptions for the

SCE574x apply to the SIP versions except the allusions

to the external clock.

The on-Board CMOS has a 140 bit RAM, one bit associ-

ated with one LED, each to generate User Defined Char-

acters. In Power Down Mode, quiescent current

is < 50 µA.

The SCE574x is designed for work with the serial port of

most common microprocessors. Data is transferred into

the displa y throu gh the Serial Data Input ( DATA) , cl oc k ed

by the Serial Data Clock (SDCLK), and enabled by the

Load Input (LOAD).

The SCE574x Clock I/ O (Cl k I/O) and Clock Select (CLK-

SEL) pins offer the user the capability to supply a high

speed ext ernal multiplex cloc k. This f eature can minimiz e

audio in-band interference for portable communication

equipment or eliminate t he visual synchronization effects

found in high vibration en vironments such as avionic

equipment.

A divide by 16 prescalar is built into the par t and can be

accessed by sof tware to reduce t he multiple x frequency if

a high speed ex ternal clock is used.

ALSO AVAILABLE WITH OPTIONS

(see page 8)

• SCE574xP-SIP

• SCE574xQ-SIP with right angle bends

FEATURES

• Four 4.57 mm (0.180") 5 x 7 Dot Matrix Characters in

Red, Yellow , Su per-red, Green, High Effi ciency Green,

Orange

• Optimum Display Surface Efficie ncy

(display area to package ratio)

• High Speed Data Input Rate: 5.0 MHz

• ROMless Serial Input, Dot Addressable Display

Ideal for User Defined Characters

• Built-in Decoders, Multiplexers and LED Drivers

• Wide Viewing Angle, X Axis ± 55°, Y Axis ± 55°

ATTRIBUTES

– 140 Bit RAM for User Defined Characters

– Eight Dimming Levels plus eight fine dimming lev-

els.

– Power Down Model (< 250 mW)

– Hardware/Software Clear Functions

– External Clock-SCE574x only

2006-03-30 2

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

Package Outlines Dimensions in mm (inch)

Ordering Information

Type Color of Emission Character Height

mm (inch) Ordering Code

SCE5740 standard red

4.57 (0.180)

Q68100A1369

SCE5741 yellow Q68100A1370

SCE5742 super-red Q68100A1371

SCE5743 green Q68100A1372

SCE5744 high efficiency green Q68100A1373

SCE5745 orange Q68100A1374

IDOD5006

10.16 (0.400)

19.91 (0.784)

4.57 (0.180)

±0.38 (0.015)

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 3

Maximum Ratings

Parameter Symbol Value Unit

Operating temperatur e range Top – 40 … + 85 °C

Storage temperature range Tstg – 40 … + 100 °C

DC Supply Voltage VCC -0.5 to + 7.0 V

Input Voltage Levels Relative to GND -0.5 to VCC +0.5 V

Solder Temperature

1.59 mm (0.063“) below seating plane, t < 5.0 s TS260 °C

Relative Humidity 85 %

ESD (100 pF, 1.5 kΩ) VZ2.0 kV

Input Current 130 mA

Maximum Number of LEDs on at 100% Brightness 64

Maximum Power Dissipation 0.6 W

Optical Characteristics at 25°C

(VCC=5.0 V at 100% brightness level, viewing angle: X axis ± 55°, Y axis ± 65°)

Description Symbol Values Unit

Red

SCE5740

Yellow

SCE5741

Super-red

SCE5742

Green

SCE5743

High Efficiency Green

SCE5744

Orange

SCE5745

Luminous Intensity (min.)

(typ.) IV30

60 60

150 60

150 80

180 60

150 µcd/dot

µcd/dot

Peak Wavelength (typ.) λpeak 655 583 630 565 568 605 nm

Dominant Wavelength (typ.) λdom 639 585 620 573 574 610 nm

Notes:

1. Dot to dot intensity matching at 100% brightness is 1.8:1.

2. Displays within a given inte nsity category have an intensity matching of 1.5:1 (max.).

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 4

Input/Output Circuits

Figures „Inputs“ and „Clock I/O“ show the input and output resis-

tor/diode networks used for ESD protection and to eliminate sub-

strate latch-up caused by input voltage over/under shoot.

Inputs Clock I/O (SCE574X only)

Electrical Characteristics (over operating temperature)

Parameter Min. Typ. Max. Units Conditions

VCC 4.5 5.0 5.5 V —

ICC (Power Down) 1) 2) ——50 µAVCC=5.0 V, all inputs=0 V or VCC

ICC 4 digits 20 dots/character3) 90 115 130 mA VCC=5.0 V, “#” displayed in all 4 digits

at 100% brightness at 25°C

IIL Input current ——–10 µAVCC=5.0 V, VIN=0 (all inputs)

IIH Input current ——10 µAVCC=VIN=5.0 V (all inputs)

VIH 3.5 ——V VCC=4.5 V to 5.5 V

VIL ——1.5 VVCC=4.5 V to 5.5 V

Row Multiplex Rate 375 768 1086 Hz —

θJC-pin ——45 °C/W —

Notes:

1) Unused inputs must be tied high.

2) External oscillator must be stopped.

3) Peak current 5/3 x ICC.

Electrical Characteristics for SCE574x only

Parameter Min. Typ. Max. Units Conditions

IOH (CLK I/O) —–28 —mA VCC=4.5 V, VOH=2.4 V

IOL (CLK I/O) —23 —mA VCC=4.5 V, VOL=0.4 V

Fext External Clock Input

Frequency 120 — 3 MHz VCC=5.0 V, CLKSEL=0

Fosc Internal Clock Inpu t

Frequency 120 —347 kHz VCC=5.0 V, CLKSEL=1

Clock I/O Bus Loading ——240 pF —

Clock Out Rise Time ——500 ns VCC=4.5 V, VOH=2.4 V

Clock Out Fall Time ——500 ns VCC=4.5 V, VOH=0.4 V

IDCD5021

GND

1 kΩInput

VCC

1 KΩ

GND

input/output

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 5

Timing Diagram—Data Write Cycle

Timing Diagram—Instruction Cycle

Switching Specifications

(over operating temperature range and VCC=4.5 V to 5.5 V)

Symbol Description Min. Units Symbol Description Min. Units

TRC Reset Active Time 600 ns TSDCW Clock Width 70 ns

TLDS Load Setup Time 50 ns TLDH Load Hold Time 0ns

TDS Data Setup Time 50 ns TDH Data Hold Time 25 ns

TSDCLK Clock Period 200 ns TWR Total Write Time 2.2 µs

TBL Time Between Loads 600 ns

Note:

TSDCW is the minimum time the SDCLK may be low or high.

The SDCLK period must be a mi nimum of 200 ns.

SDCLK

SDCW

DATA

LOAD

LDS

TDH

LDH

LOAD

DATA

SDCLK

D0 D1 D2 D3 D4 D5 D6 D7

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 6

Top View

Dot Matrix Format

Pin Assignment

Pin Function Pin Function

1VCC 14 CLK SELECT

2LOAD 13 no pin

3DATA 12 no pin

4no connection 11 no pin

5SDCLK 10 no pin

6RST 9no pin

7GND 8CLK I/O

IDPA5105

Digit 0 Digit 1 Digit 2 Digit 3

Pins17

Pins14 8

Dimensions in inches (mm)

Tolerance: ±0.25 (0.010)

1.14 (0.045) typ.

4.45 (0.175)

0.23 (0.009) typ. 1.09 (0.043) typ.

C1 C2

IDOD5013

6.86 (0.270)

C3 C4 C5 R0

Pin Definitions

Pin Function Definitions

1VCC Power supply

2LOAD Low input enables data clocking into 8-bit

serial shift register. When LOAD goes hig h,

the contents of 8-bit serial Shift Register will

be decoded.

3DATA Serial data inpu t

4 N/C no connection

5SDCLK for loading data into the 8-bit serial data

6RST Asynchronous input, when lo w clears the

Multiplex Counter, Control Word Register,

User RAM and Data Register. Con trol Word

display will be blank.

7 GND Supply ground

8CLK I/O Outputs master clock or inputs e xternal clock.

9 N/P No pins

10 N/P No pins

11 N/P No pins

12 N/P No pins

13 N/P No pins

14 CLKSEL H=internal clock, L=external clock

Display Column and Row Format

C0 C1 C2 C3 C4

Row 0 11111

Row 1 00100

Row 2 00100

Row 3 00100

Row 4 00100

Row 5 00100

Row 6 00100

1= Display dot „ON“

0=Display dot „OFF“

Column Data Ranges

Row 0 00H to 1FH Row 4 00H to LFH

Row 1 00H to LFH Row 5 00H to LFH

Row 2 00H to LFH Row 6 00H to LFH

Row 3 00H to LFH

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 7

Block Diagram

Operation of the SCE574x

The SCE574x display consists of a CMOS IC containing control

logic and drivers for four 5 x 7 characters. These components are

assembled in a compact plastic package.

Individual LED dot addressability al lows the user great freedo m in

creating special characters or m ini-icons.

The serial data interf ace prov ides a high ly efficient in terconne ction

between th e displa y an d the mo ther board . The SCE5 74x requ ires

only three lines as compared to 14 lines for an eq uivalen t four

character parallel input part.

The on-board CMOS IC is the electronic heart of the display. The

IC accepts decoded serial data, which is stored in the internal

RAM. Asynchronously the RAM is read by the character multi-

plexer at a strobe rate that results in a flicker free display. Figure

„Block Diagram“ (page 7) shows the three functional areas of the

IC. These include: the input serial dat a registe r and control logic , a

140 bits two port RAM, and an internal multi plexer/display driver.

The following explains how to format the serial data to be loaded

into the display. The user supplies a string of bit mapped decoded

characters . The co nte nts of this string is shown in Figure „Loa di n g

Serial Character Data a“ (page 8). Figure „Loading Serial Charac-

ter Data b“ (page 8) shows that each character consist of eight 8

bit words. The first word encodes the display character location

and the succeeding five bytes are row data. The row data repre-

sents the status (On , Off) of indi vidual colu mn LE Ds . Figu re „Lo ad-

ing Serial Ch aracter D ata c“ (page 8) sho ws that each 8 bit w ord is

formatted to represent Column Data or Character Address.

Figure „Loading Serial Character Data d“ (page 8) shows the

sequence for loading the bytes of data. Bringing the LOAD line low

enables the serial register to accept data. The shift action occurs

on the low to high transition of the serial data clock (SDCLK). The

least significa nt bi t (D 0 ) is loaded first. After eight clock pulses the

LOAD line is brought high. With this transition the OPCODE is

decoded. The decoded OPCODE directs D4–D0 to be latched in

the Characte r Address register, stored in the RAM as Column

data, or latched in the Control Word register. The control IC

requires a minimum 600 ns delay between successive byte loads.

IDBD5063

Memory

Y Address Decode

User RAM Drivers

Digit

Column

0 to 4

7 x 20 bits

X Address Decode

3-bit Address Register

6-bit Control

Word Register

Control Word Logic

Column 0 to 20

Display

123

and Row Drivers

Row Control Logic

Counter

764

Counter

OSC

8-bit Serial Register

Rows

0 to 6

MUX

Rate

DATA

SDCLK

LOAD

CLKSEL

CLK I/O

RST

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 8

Loading Serial Character Data

Table „Character ’D’“ (page 8) shows the Row Address for the

example character “D.” Column data is written and read asynchro-

nously from the 140 bit RAM. Once loaded the internal oscillator

and character multiplexer reads the data from the RAM. These

characters are row strobed with colu mn data as shown in Fig ures

„Row and Columns Locations for a Character ’D’“ (page 8) and

„Row Strobing“ (page 9). The character strobe rate is determined

by the internal or user supplied external MUX Clock, th e IC’s

counter and the prescaler.

Row and Column Locations for a Character “D”

Character 0 Character 1 Character 2 Character 3

352 Clock Cycles, 70.4 µs

xample: Serial Clock=5.0 MHz, Clock Period=200 ns

Time between Loads

LOAD

Serial

Clock

DATA

Clock

Period

D0 D1 D2 D3 D4 D5 D6 D7

11 Clock Cycles, 2.2 µs

Time

Between

Loads

600ns(min)

OPCODE

Character Address OPCODE

Column Data

D D1

D D2

D D3

D D4

11 Clock Cycles, 2.2 µs

Character 0

Address

Row 0

Column Data Row 1

Column Data Row 2

Column Data Row 3

Column Data Row 4

Column Data Row 5

Column Data Row 6

Column Data

88 Clock Cycles, 17.6 µs

0 D1

0 D2

0 D3

0 D4

0 D5

1 D6

0 D7

0 D6

0 D7

Time

Between

Loads

600ns(min)

Character “D”

Op code

D7 D6 D5 Column Data

D4 D3 D2 D1 D0

C0 C1 C2 C3 C4

Hex

Row 0 000 11110 1E

Row 1 000 10001 11

Row 2 000 10001 11

Row 3 000 10001 11

Row 4 000 10001 11

Row 5 000 10001 11

Row 6 000 11110 1E

IDXX5183

Row 2

Row 3

Row 4

Row 5

Row 6 01234

On LED

Off LED

Columns

Row 0

Row 1

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 9

Row Strobing

Multiplexer and Displ ay Driver

The four characters are row multiplexed with RAM resident column

data. The strobe rate is established by the internal or external

MUX Clock rate. The MUX Clock frequency is divided by a 448

counter chain. This results in a typical strobe rate of 768 Hz. By

pulling the Cl ock SEL l ine low, the displa y can be op erated from an

external MUX Cloc k. The exte rnal cloc k is a tta che d to the CL K I /O

connection (pin 8). The maximum external MUX Clock frequency

should be limited to 3 MHz.

When a high speed external clock is used the frequency can be

further divided down by 16 by using the built in prescaler. In the

control word format data bit D4 is set high (D4=1). It is not recom-

mended to use the prescaler with the inte rnal cloc k.

An asynchronous hardware Reset (pin 6) is also provided. Bring-

ing this pin low will clear the Character Address Register, Control

Word Register , RAM, a nd blanks th e displa y. This actio n leav es the

display set at Character Address 0, and the Brightness Level set at

100%.

The user can activate four Control functions. These include: LED

Brightness Level, IC Power Down, Prescaler, or Display Clear.

OPCODEs and six bit words are used to initiate these functions.

The OPCODEs and Control Words for the Character Address and

Loading Column Data are shown in Tables „Load Character

Address“ (page 10) and „Load Column Data“ (page 10).

Control Word Format

Columns

1234

Load

Row Load Row 0

Columns

01234 Columns

01234

Load Row 1 Load Row 2 Load Row 5

Columns

012340

Columns

1234 01

Load Row 4Load Row 3

Columns

IDXX5184

234 01234

Load Row 6

Basic Instruction Set

Instruction Opcode Address/Data Comments

LCD 000 D4 D3 D2 D1 D0 Load Column Data

LDA 101 X X A2 A1 A0 Load Digit Address

SCL 110 PS B3 B2 B1 B0 Software Clear

LCWD 111 PS B3 B2 B1 B0 Load Control Word Data

IDCW5162

1D6

1D5

1D4

PS D3

B3 D2

B2 D1

B1 D0

6.6%

B2 100%

27%

40%

20%

13%

53%

BrightnessB1

0B0

010

101

111 Blank Display &

Power Down

1Full

Reduce to 12.5%

Pre-Scalar

MUX Clock/16

0 No Divide

1by 16

B3 Peak Current

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 10

The user can select eight specific LED brightness levels (Table

„Display Brightness“ (page 10)) by changing the peak current driv-

ing the LEDs . The peak curren t is va ried by varying the ON time of

the row drivers. Note that data line 3 is low (logic 0).

If dimming is requ ire d with fine r co ntrol be twee n 12 .5% brightne ss

and 0.0% brightness, data line 3 can be set high (logic 1). The

12.5% peak current is now the brightness reference (100%-E8) for

further dimming and as shown in Table “Display Brightness“

(page 10) eight levels of dimming are provided. For example the

hex co de E C in Table “D isplay Brightness“ (page 10) will provide a

brightness level 29% lower than the 12.5% brightness level.

The SCE574X offers a unique Display Power Down feature which

reduces ICC to less than 50 µA. When EFHEX is loaded, as shown in

Table „Power Down“ (page 10), the display is set to 0% brightness .

When in the Power Down mode data may still be written into the

RAM. The displa y is react ivat ed by lo ading a new Brightness Le v el

Control Word into the display.

The Software Clear (C0HEX), given in Table „Software Clear“

(page 10), clears the Address Register and the RAM. The display

is blanked and the Character Address Register will be set to Char-

acter 0. The internal counter and the Control Word Register are

unaffected. The Software Clear will remain active until the next

data input cycle is initiated.

Load Character Address

Op code

D7 D6 D5 Character Address

D4 D3 D2 D1 D0 Hex Operation

Load

101 00 0 0 0 A0 Character 0

101 00 0 0 1 A1 Character 1

101 00 0 1 0 A2 Character 2

101 00 0 1 1 A3 Character 3

Load Column Data

Op code

D7 D6 D5 Column Data

D4 D3 D2 D1 D0 Operation Load

000 C0 C1 C2 C3 C4 Row 0

000 C0 C1 C2 C3 C4 Row 1

000 C0 C1 C2 C3 C4 Row 2

000 C0 C1 C2 C3 C4 Row 3

000 C0 C1 C2 C3 C4 Row 4

000 C0 C1 C2 C3 C4 Row 5

000 C0 C1 C2 C3 C4 Row 6

Display Brightness

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

111 00 0 0 0 E0 100%

111 00 0 0 1 E1 53%

111 00 0 1 0 E2 40%

111 00 0 1 1 E3 27%

111 00 1 0 0 E4 20%

111 00 1 0 1 E5 13%

111 00 1 1 0 E6 6.6%

111 00 1 1 1 E7 0.0%

Power Down

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

111 01 1 1 1 EF 0%

brightness

Software Clear

Op code

D7 D6 D5 Control Word

D4 D3 D2 D1 D0 Hex Operation

Level

110 00 0 0 0 C0 CLEAR

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 11

Electrical and Mechanical Considerations

Thermal Considerations

Optimum product performance can be had when the following

electrical and mechanical recommendations are adopted. The IC

is constructed in a hig h speed CMOS pr ocess, consequently noise

on the SERIAL DATA, SERIAL DATA CLOCK, LOAD and RESET

lines may cause incorrect data t o be written into the serial shift reg-

ister. Adhere to transmission line termination procedures when

using fast line drivers and long cables (> 10 cm).

Good ground and power supply decoupling will insure that

ICC (< 400 mA peak) switching currents do not generate localized

ground bounce. Therefore it is recommended that each dis play

package use a 0.1 µmF and 0 µF capacitor between VCC and

ground.

When the internal MUX Clock is being used connect the CLKSEL

pin to VCC. In those applications where RESET will not be con-

nected to the system’s reset control, it is recommended that this

pin be connect ed to the center no de of a se ries 0.1 µF and 100 kΩ

RC network. Thus upon initi al power up the RESET will be held

low for 10 ms allowing adequate time fo r the system power supply

to stabilize.

ESD Protection

The input protection st ructur e of the SCE574x provides significant

protection against ESD damage. It is capable of withstanding dis-

charges greater than 2.0 kV. Take all the standard precautions,

normal for CMOS components. These include properly grounding

personnel, tools, tables, and transport carriers that come in con-

tact with unshi elded parts. If these condi tions are not, or cannot be

met, keep the leads of the device shorted together or the parts in

anti-static packaging.

Soldering Considerations

The SCE574x can be hand soldered with SN63 solder using a

grounded iron set to 260°C.

Wave soldering is also possible following these conditions: Pre-

heat that does n ot e xceed 93°C on t he solder side of t he PC boar d

or a package surface temperature of 85°C. Water soluble organic

acid flux (except carboxylic acid) or rosin-based RMA flux without

alcohol can be used.

Wa ve temperature of 245°C ± 5°C with a dwell betw een 1.5 sec. to

3.0 sec. Exposure to the wave should not exceed temperatures

above 260°C for five seconds at 1.59 mm (0.063") below the seating

plane. The packages should not be immersed in the wav e .

Po st Solder Cl eaning Procedures

The least offensive cleaning solution is hot D.I. water (60 °C) for

less than 15 min utes. Add ition of mild saponifiers is acceptable. Do

not use commercial dishwasher d etergents.

For faster cleaning, solvents may be used. Exercise care in choos-

ing solvents as some may chemically attack the nylon package.

For further information refer to Appnote s 18 and 19.

An alternative to soldering and cleaning the display modules is to

use sockets. Naturally, 14 pin DIP socke ts 7.62 mm (0.300”) wide

with 2.54 mm (0.100") centers work well for single displays. Multi-

ple display assemblies are best handled by longer SIP sockets or

DIP sockets when available for uniform package alignment.

Optical Considerations

The 4.57 mm (0.180") high character of the SCE574x gives read-

ability up to five feet. Proper filter selection enhances readability

over this distance.

Using filters emphasizes the contrast ratio between a lit LED and

the character background. This will increase the discrimination of

different characters. The only limitation is cost. Take into consider-

ation the ambient lighting environment for the best cost/benefit

ratio for filters.

Incandescent (wit h almost no g reen) or fluorescent (w ith almost no

red) lights do not have the flat spectral response of sunlight. Plas-

tic band-pass filter s are an in expensive and effective wa y to

strengthen contrast ratios. The SCE5740 is a red display and

should be used with long wavelength pass filter having a sharp

cut-off in the 600 nm to 620 nm range. The SCE5742 is a

super-red display and should be used with long wavelength pass

filter having a sharp cut-off in the 570 nm to 600 nm range. The

SCE5744 is a high efficiency green display and should be used

with long wavelength pass filter that peaks at 565 nm.

Additional contrast enhancement is gained by shading the

display s. Plastic band -pass filters with b uilt-in louv ers off er the ne xt

step up in contrast improvement. Plastic filters can be improved

further with anti-reflective coatings to reduce glare.

Optimal filter enhancements are gained by using circular polar-

ized, anti-ref lective, band-pass filters. The ci rcular polarizing fur-

ther enhances contrast by reducing the light that travels through

the filter and reflects back off the display to less than 1%.

Several filter manufacturers supply quality filter materials. Some of

them are: Panelgraphic Corporation, W. Caldwell, NJ; SGL Homa-

lite, Wilmington, DE; 3M Company, Visual Products Division, St.

Paul, MN; Polaroid Corporation, Polarizer Division, Cambridge,

MA; Marks Polarized Corporation, Deer Park, NY, Hoya Optics,

Inc., Fremont, CA.One last note on mounting filters: recessing dis-

plays and bezel assemblies is an inexpensive way to provide a

shading effect in overhead lighting situations. Several Bezel manu-

facturers are: R.M.F. Products, Batavia, IL; Nobex Components,

Griffith Plastic Corp., Burlingame, CA; Photo Chemical Products of

California, Santa Monica, CA; I.E.E.-Atlas, Van Nuys, CA. The

trade-off is fuzzy characters . Mounting the filter s close to the dis-

play reduces this effect. Take care not to overheat the plastic filter

by allowing for proper air flow.

Microprocessor Interface

The microp rocessor interf a ce is t hrough the serial port, SPI port or

one out of ei ght d ata bits on th e ei ght bi t pa ra llel po rt and also con -

trol lines SDCLK and LOAD.

Power Up Sequence

Upon power up display will come on at random. Thus the display

should be reset at power-up. The reset will set the Address Regis-

ter to Digit 0, User RAM is set to 0 (display blank) the Control Word

is set to 0 (100% brightness) and the internal counters are reset.

2006-03-30 12

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

Display Interface to Siemens/Intel 8031 Microprocessor (using serial port in mode 0)

Display Interface to Siemens/Intel 8031 Microprocessor (using one bit of parallel por t as serial port)

Display Interface with Motorola 68HC05C4 Micr opro cessor (using SPI port)

IDCD5027

XTAL2 RxD

18 10

19 XTAL1

RST

917

P3.7

P3.3

P3.4 14

8031

TxD 11 SDCLK

RST

GND CLKSEL

CLK I/O

DATA

0.01 µF

TAN

22 µF

IDCD5028

XTAL2 P3.0

18 10

19 XTAL1

RST

8031

U1 SDCLK

RST

GND CLKSEL

CLK I/O

DATA

0.01 µF

TAN

22 µF

P1.0

P3.1 11

P3.6 16

P0.0 39

IDCD5029

OSC1 PA0

38 11

39 OSC2

RST

68HC05C4

U1 SDCLK

RST

GND CS

CLK I/O

DATA

0.01 µF

TAN

22 µF

PA2

PA1 10

SCLK 33

MOSI 32

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 13

Cascading Multiple Displays using only the SCE574x.

Multiple displays can be cascaded using the CLK SEL and CLK I/O pins (Figure „Cascading Multiple Display s using only the SCE574X“

(page 13)). The display designated as the MasterClock source should have its CLK SEL pin tied high and the slaves should have their

CLK SEL pins tied low. All CLK I/O pins should be tied together. One display CLK I/O can drive 15 slave CLK I/Os. Use RST to synchro-

nize all display counters.

Loading Data into the Display

Use following procedure to load data into the display:

1. Power up the display.

2. Bring RST low (600 ns duration minimum) to clear the Multi-

plex C oun ter, Address Register, Control Word

blank. Display brightness is set to 100%.

3. If a different brightness is desired, load the proper brightness

opcode into the Control Word Register.

4. Load the Digit Address into the display.

5. Load display row and column data for the selected digit.

6. Repeat steps 4 and 5 for all digits.

IDCD5030

RST CLK SEL

Intelligent Display

DATA SDCLK LOAD

14 more displays

in between

DATA

SDCLK

Decoder

Address Address Decode 1-14

RST

CLK I/O

Intelligent Display

DATA

RST

SDCLK

CLK I/O

LOAD

CLK SEL

Chip

LD CE

Data Contents for the Word “ABCD”

Step D7 D6 D5 D4 D3 D2 D1 D0 Function

B (optional) 1 1 0

1 1 1 00 0 0 0

00 0 0 0 CLEAR

100% BRIGHTNESS

10 1

00 0

0 0 0

00 0 0 0

00100

01 0 1 0

10 0 0 1

11 1 1 1

10001

10 0 0 1

DIGIT D0 SELECT

ROW 0 (A)

ROW 1 (A)

ROW 2 (A)

ROW 3 (A)

ROW 4 (A)

ROW 5 (A)

ROW 6 (A)

1 0 1

00 0

0 0 0

00001

11111

10001

10 0 0 1

11 1 1 0

10 0 0 1

11 1 1 1

DIGIT D1 SELECT

ROW 0 (B)

ROW 1 (B)

ROW 2 (B)

ROW 3 (B)

ROW 4 (B)

ROW 5 (B)

ROW 6 (B)

1 0 1

0 0 0

00 0 1 0

00111

01000

10 0 0 0

10000

01 0 0 0

00 1 1 1

DIGIT D2 SELECT

ROW 0 (C)

ROW 1 (C)

ROW 2 (C)

ROW 3 (C)

ROW 4 (C)

ROW 5 (C)

ROW 6 (C)

1 0 1

0 0 0

00011

11 1 1 0

10 0 0 1

10001

10 0 0 1

10001

11110

DIGIT D3 SELECT

ROW 0 (D)

ROW 1 (D)

ROW 2 (D)

ROW 3 (D)

ROW 4 (D)

ROW 5 (D)

ROW 6 (D)

2006-03-30 14

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

Detail Drawing of SCE574x Dimensions in inch (mm)

Pin Functions for SCE574x

Pin # Function Pin # Function Top View Typical Character

1 VCC 6RESET

2Load 7GROUND

3 Data 8 CLK I/O

4No Pin 9—13 No Pins

5SDCLK 14 CLK

SELECT

Dimensions in

inches (mm)

Tolerance:

.XXX = ±.010 (.25)

IDOD5007

10.16 (0.400)

±0.38 (0.015)

19.91 (0.784)

4.57 (0.180)

2.54 (0.100) 5.00 (0.197)

5.08 (0.200)

7.62 (0.300)

±0.51 (0.020)

±0.05 (0.002)

0.3 (0.012)

3.81 (0.150)

4.06 (0.160)

±0.51 (0.020)

SCE574X Z

OSRAM XXYY V

0.46 (0.018)

2.54 (0.100) 12 pl.

Non cumulative

Pin 1

Indicator Part Number Date Code

EIA

Luminous

Intensity Code

3 pl.

IDPA5107

Pin 1 Pin 7

Pin 14 Pin 8

IDOD5008

0.71 (0.028)

0.56 (0.022)

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

2006-03-30 15

IDOD5011

0.71 (0.028)

0.56 (0.022)

IDOD5011

0.71 (0.028)

0.56 (0.022)

IDOD5011

0.71 (0.028)

0.56 (0.022)

Detail Drawing of SCE574xP (SIP configuration) Dimensions in inch (mm)

Detail Drawing of SCE574xQ (SIP configuration with right angle bend Dimensions in inch (mm))

Pin Functions for SCE574xP and SCE574xQ

Pin # Function Top View Typical Character

1VCC

2Load

3 Data

4No Pin

5SDCLK

6RESET

7 GND

IDOD5009

10.16 (0.400)

19.91 (0.784)

4.57 (0.180)

2.54 (0.100) 4 pl.

5 (0.197)

3 pl.

5.08 (0.200)

0.3 (0.012) 6 pl.

3.81 (0.150)

4.06 (0.160)

±0.51 (0.020)

SCE574XP Z

OSRAM XXYY V

0.46 (0.018) 8 pl.

2.54 (0.100) 4 pl.

Tol. Non Accum.

Pin 1

Indicator Part Number Date Code

EIA

Luminous

Intensity Code

5.08 (0.200)

1.22 (0.048)

Unless otherwise specified,

tolerance on dimensions is ±0.25 (0.010)

IDOD5010

10.16 (0.400)

19.91 (0.784)

SCE574XQ Z

OSRAM

XXYY V

Pin 1

Indicator Number

EIA

Luminous

Intensity Code

Unless otherwise specified,

0.46 (0.018) 6 pl.

5.08 (0.200)

2.54 (0.100) 4 pl.

Tol. Non Accum.

Date Code

1.26 (0.050)±0.51 (0.020)

3.81 (0.150)

5.08 (0.200)

±0.51 (0.020)

4.06 (0.160)

1.22 (0.048) 5 (0.197)

3 pl.

4.57 (0.180)

2.54 (0.100) 4 pl.

Part

tolerance on dimensions is ±0.25 (0.010)

IDPA5108

Pin 1 Pin 7

IDOD5011

0.71 (0.028)

0.56 (0.022)

2006-03-30 16

SCE5740, SCE5741, SCE574 2, SCE5743, SCE5744, SCE5745

Published by

OSRAM Opto Semiconductors GmbH

Wernerwerkstrasse 2, D-93049 Regensburg

www.osram-os.com

Attention please!

The information describes the type of component and shall not be considered as assured characteristics.

Terms of delivery and rights to change design reserved. Due to technical requirements components may contain

dangerous substances. For information on the types in question please contact our Sales Organization.

If printed or downloaded, please find the latest version in the Internet.

Packing

Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office.

By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing

material that is retu rned to us unsorted or which we are not obliged to a ccept, we shall have t o invoice you for any costs

incurred.

Components used in life-support devices or systems must be expressly authorized for such purpose! Critical

components1) may only be used in life-support devices or systems2) with the express written approval of OSRAM OS.

1) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the

failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system.

2) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain

human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered.

Revision History: 2006-03-30

Previous Version: 2005-01-10

Page Subjects (major changes since last revision) Date of change

all Lead free device 2006-01-23