CSM_E2S_DS_E_9_3
1
Super-compact Proximity Sensor
E2S
Advanced Performance and Wide
Range of Selections in a Super-
compact Size
• Only 5.5 × 5.5 mm with a built-in Amplifier.
• Maximum sensing distance: 2.5 mm. Stable detection even with
workpiece fluctuations.
• Response frequency: 1 kHz.
• Low current consumption.
Ordering Information
Sensors [Refer to Dimensions on page 7.]
DC 2-Wire Models
*1. Models with a different frequency are also available to prevent mutual interference. The model numbers are E2S-@@@B (e.g., E2S-W11B).
*2. Models are also available with robotics (bend resistant) cables. Add “-R” to the model number.(e.g., E2S-W11-R 1M)
DC 3-Wire Models
*1. Models with a different frequency are also available to prevent mutual interference. The model numbers are E2S-@@@B (e.g., E2S-W13B).
*2. Models are also available with robotics (bend resistant) cables. Add “-R” to the model number.(e.g., E2S-W13-R 1M)
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions on
page 6.
Appearance Sensing surface Sensing distance
Model
Operation mode
NO NC
Top E2S-W11 1M *1 *2 E2S-W12 1M
Front E2S-Q11 1M *1 *2 E2S-Q12 1M
Top E2S-W21 1M *1 *2 E2S-W22 1M *2
Front E2S-Q21 1M *1 *2 E2S-Q22 1M *2
Unshielded
1.6 mm
2.5 mm
Appearance Sensing surface Sensing distance Output
configuration
Model
Operation mode
NO NC
Top
NPN
E2S-W13 1M *1 *2 E2S-W14 1M
Front E2S-Q13 1M *1 *2 E2S-Q14 1M
Top E2S-W23 1M *1 *2 E2S-W24 1M *2
Front E2S-Q23 1M *1 *2 E2S-Q24 1M *2
Top
PNP
E2S-W15 1M *1 E2S-W16 1M
Front E2S-Q15 1M *1 E2S-Q16 1M
Top E2S-W25 1M *1 E2S-W26 1M
Front E2S-Q25 1M *1 E2S-Q26 1M
Unshielded
1.6 mm
2.5 mm
1.6 mm
2.5 mm
E2S
2
Accessories (Order Separately)
Mounting Brackets Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required.
[Refer to Dimensions on page 7.]
Model Number Legend
Appearance Model Quantity Remarks
Y92E-C1R6
1
Provided with E2S-@1@@.
(fixed with one screw)
Y92E-C2R5 Provided with E2S-@2@@.
(fixed with one screw)
Y92E-D1R6 For E2S-@1@@
(fixed with two screws)
Y92E-D2R5 For E2S-@2@@
(fixed with two screws)
(5) (6)(4)(3)(2)(1)
E2S- @ @ @ @ -@
(1) Compact
Square
Series
(2) Sensing Direction
W: Top surface detection
Q: Front surface detection
(3) Size and Sensing Distance
(Standard Sensing Object)
1: 5.5 × 5.5 mm, 1.6 mm (iron)
2: 8 × 8 mm, 2.5 mm (iron)
(4) Output
1: DC 2-wire NO
2: DC 2-wire NC
3: DC 3-wire NPN NO
4: DC 3-wire NPN NC
5: DC 3-wire PNP NO
6: DC 3-wire PNP NC
(5) Different Frequency
Blank: Standard
B: Different frequency
(6) Robotics (bend resistant)
cables
Blank: Standard
R: Robotics (bend
resistant) cables
3
E2S
Ratings and Specifications
DC 2-Wire Models
* The response frequency is an average value.
Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
DC 3-Wire Models
* The response frequency is an average value.
Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
Model E2S-W11
E2S-W12
E2S-Q11
E2S-Q12
E2S-W21
E2S-W22
E2S-Q21
E2S-Q22
Item
Sensing surface Top Front Top Front
Sensing distance 1.6 mm ±15% 2.5 mm ±15%
Set distance 0 to 1.2 mm 0 to 1.9 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)
Standard sensing
object Iron, 12 × 12 × 1 mm Iron, 15 × 15 × 1 mm
Response frequency *1 kHz min.
Power supply voltage
(operating voltage
range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Leakage current 0.8 mA max.
Control
output
Load
current 3 to 50 mA max.
Residual
voltage 3 V max. (under load current of 50 mA with cable length of 1 m)
Indicators @@1 Models: Operation indicator (red), Setting indicator (green)
@@2 Models: Operation indicator (red)
Operation mode
(with sensing object
approaching)
@@1 Models: NO
@@2 Models: NC Refer to the timing charts under I/O Circuit Diagrams on page 5 for details.
Model E2S-W13
E2S-W14
E2S-Q13
E2S-Q14
E2S-W23
E2S-W24
E2S-Q23
E2S-Q24
E2S-W15
E2S-W16
E2S-Q15
E2S-Q16
E2S-W25
E2S-W26
E2S-Q25
E2S-Q26
Item
Sensing surface Top Front Top Front Top Front Top Front
Sensing distance 1.6 mm ±15% 2.5 mm ±15% 1.6 mm ±15% 2.5 mm ±15%
Set distance 0 to 1.2 mm 0 to 1.9 mm 0 to 1.2 mm 0 to 1.9 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)
Standard sensing
object Iron, 12 × 12 × 1 mm Iron, 15 × 15 × 1 mm Iron, 12 × 12 × 1 mm Iron, 15 × 15 × 1 mm
Response frequency *1 kHz min.
Power supply voltage
(operating voltage
range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Current consumption 13 mA max. at 24 VDC (no-load)
Control
output
Load
current NPN open-collector output, 50 mA max. (30 VDC max.) PNP open-collector output, 50 mA max. (30 VDC max.)
Residual
voltage 1.0 V max. (under load current of 50 mA with cable length of 1 m)
Indicators Operation indicator (orange)
Operation mode
(with sensing object
approaching)
@@3 Models: NO
@@4 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on
page 5 for details.
@@5 Models: NO
@@6 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on
page 5 for details.
E2S
4
Specifications
Engineering Data (Reference Value)
Item Model E2S-@@@
Protection circuits Reverse polarity protection, Surge suppressor
Ambient temperature
range Operating: −25 to 70°C (with no icing or condensation), Storage: −40 to 85°C (with no icing or condensation)
Ambient humidity
range Operating: 35% to 90% (with no condensation), Storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C in the temperature range of −25 to 70°C
Voltage influence ±2.5% max. of sensing distance at rated voltage in rated voltage ±10% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC for 1 min between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 1 m)
Weight (packed state) Approx. 10 g
Materials Case Polyarylate resin
Accessories Mounting Brackets
Sensing Area
E2S-W1@/-W2@E2S-Q1@/-Q2@
Influence of Sensing Object Size and Material
E2S-W1@/-Q1@E2S-W2@/-Q2@
4
3
2
1
0
−2−1−3−443210
Y
X
E2S-W2@
E2S-W1@
Distance Y
(mm)
Distance X (mm)
E2S-W1@ Sensing Head
E2S-W2@ Sensing Head
2
1.5
1
0.5
100
X
50403020
d ´
d t = 1 mm
Side length of sensing object: d (mm)
Distance X (mm)
Copper
Iron
Aluminum
Brass
Stainless steel (SUS304)
X
4
3
2
1
2010060504030
d ´
d
Side length of sensing object: d (mm)
Distance X (mm)
Copper
Iron
Aluminum
Brass
Stainless steel (SUS304)
5
E2S
I/O Circuit Diagrams
DC 2-Wire Models
DC 3-Wire Models
Operation
mode Model Timing chart Output circuit
NO
E2S-W11
E2S-W21
E2S-Q11
E2S-Q21
NC
E2S-W12
E2S-W22
E2S-Q12
E2S-Q22
Operation
mode
Output con-
figuration Model Timing chart Output circuit
NO
NPN
E2S-W13
E2S-W23
E2S-Q13
E2S-Q23
NC
E2S-W14
E2S-W24
E2S-Q14
E2S-Q24
NO
PNP
E2S-W15
E2S-W25
E2S-Q15
E2S-Q25
NC
E2S-W16
E2S-W26
E2S-Q16
E2S-Q26
080100
(%)
Sensing
object
Rated
sensing
distance
Stable sensing
area
Non-sensing
area
Unstable
sensing
area
Set position
Proximity Sensor
ON
OFF
ON
OFF
ON
OFF
Setting indicator (green)
Operation indicator (red)
Control output
0 V
+V
Load
Brown
Blue
Proximity
Sensor
main
circuit
Note: The load can be connected to either
the +V or 0 V side.
0100
(%)
Sensing
object
Rated
sensing
distance
Sensing areaNon-sensing area
Proximity Sensor
ON
OFF
ON
OFF
Operation indicator (red)
Control output
Present
Not present
ON
OFF
ON
OFF
Sensing object
Operation indicator
(orange)
Output transistor
(load)
0 V
+V
*
Load
Brown
Black
Output
Blue
Proximity
Sensor
main
circuit
* Load current: 50 mA max.
Output transistor
(load)
Present
Not present
ON
OFF
ON
OFF
Sensing object
Operation indicator
(orange)
Present
Not present
ON
OFF
ON
OFF
Output transistor
(load)
Sensing object
Operation indicator
(orange)
0 V
+V
*
Load
Brown
Black
Blue
Proximity
Sensor
main
circuit
* Load current: 50 mA max.
Output transistor
(load)
Present
Not present
ON
OFF
ON
OFF
Sensing object
Operation indicator
(orange)
E2S
6
Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use this product under ambient conditions that exceed the
ratings.
● Design
Influence of Surrounding Metal
•When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the
performance of the Sensor.
•Models with Top Sensing Surface
(Unit: mm)
•Models with Front Sensing Surface
(Unit: mm)
Mutual Interference
When installing Sensors face-to-face or side-by-side, ensure that the
minimum distances given in the following table are maintained.
(Unit: mm)
*1. Values in parentheses apply to Sensors operating at different frequencies.
*2. Mutual interference will not occur for close-proximity mounting if models with
different frequencies are used together.
● Mounting
Tightening Torque
For the E2S-W(Q)2@, the maximum tightening torque that should be
applied to the mounting screws is 0.7 N·m.
Applicable e-CON Connector Models and Manufacturers
The companies and model number of e-CON connections that can be used with Sensor cables are listed in the following table.
Confirm applicability when purchasing e-CON connectors for connection to Pre-wired Sensors.
WARNING
Precautions for Correct Use
Model Distance ABC
E2S-W1@
082
E2S-W2@15 10
Model Distance ABC
E2S-Q1@832
E2S-Q2@15 10 3
A
CBC
Sensing surface
Proximity
Sensor
Sensing
surface
Proximity
Sensor
Metal not
exceeding height
of Sensor surface
Metal exceeding
height of Sensor
surface
AB
B
C
•Models with Top
Sensing Surface
•Models with Front Sensing Surface
Model Distance A B
E2S-W(Q)1@50 (40) *1 20 (5.5) *1, *2
E2S-W(Q)2@75 (50) *1 25 (8) *1, *2
ABB
A
Model Applicable e-CON Connector Manufacturer
E2S-W@3/4 XN2A-1470 Cable Plug Connector OMRON
E2S-Q@3/4
7
E2S
Dimensions
Sensors
(Unit: mm)
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E2S-W1@
8.4 5.9
R1.5
25.1
22.3
22
2.6
2
2.3
5.9
5.5 6.4
119
*E2S-W11@
E2S-W12@
E2S-W13@
E2S-W14@
E2S-W15@
E2S-W16@
Indicator*
2.9-dia. vinyl-insulated
round cable with 2/3
conductors (Conductor
cross section: 0.14 mm2,
Insulator diameter: 0.9 mm),
Standard length: 1 m
Sensing surface
Operation indicator
(orange)
Operation indicator (red),
Setting indicator (green)
Operation
indicator (red)
With Mounting Bracket Attached
*E2S-Q11@
E2S-Q12@
E2S-Q13@
E2S-Q14@
E2S-Q15@
E2S-Q16@
R1.5
2
25.1
22.3
2
19
1
8.4 5.9
2
2.3
5.9
5.5 6.4
2.9-dia. vinyl-insulated
round cable with 2/3
conductors (Conductor
cross section: 0.14 mm2,
Insulator diameter: 0.9 mm),
Standard length: 1 m
Sensing surface
Indicator*
Operation indicator
(orange)
Operation indicator (red),
Setting indicator (green)
Operation indicator
(red)
E2S-Q1@
With Mounting Bracket Attached
E2S-W2@
2
2
20
11.3
7.8
7.4
*E2S-W21@
E2S-W22@
E2S-W23@
E2S-W24@
E2S-W25@
E2S-W26@
8
10.1
15.5
11.5
7.4
3
5.3
2.38
2.5 10.8
3.1-dia. mounting hole
Sensing surface
Indicator*
2.9-dia. vinyl-insulated
round cable with 2/3
conductors (Conductor
cross section: 0.14 mm2,
Insulator diameter: 0.9 mm),
Standard length: 1 m
3.1 dia.
Operation indicator
(orange)
Operation indicator (red),
Setting indicator (green)
Operation indicator (red)
With Mounting Bracket Attached
E2S-Q2@
2.5
3.1 dia.
10.8
8.9
8.4
8
2.3
8
2.5
2
2
5.3
323
11.3
18.5
4.1 3.6
14.5 *E2S-Q21@
E2S-Q22@
E2S-Q23@
E2S-Q24@
E2S-Q25@
E2S-Q26@
Sensing surface
Indicator*
2.9-dia. vinyl-insulated round cable
with 2/3 conductors (Conductor
cross section: 0.14 mm2, Insulator
diameter: 0.9 mm), Standard length:
1 m
3.1-dia. mounting hole
Operation indicator
(orange)
Operation indicator (red),
Setting indicator (green)
Operation indicator (red)
With Mounting Bracket Attached
E2S
8
Accessories (Order Separately)
11.3
Two, R1.2
Two, R0.7
0.4
2.3
2
5.7
3.5
1.3
1.1
6.4
5.6
R1.2
20.4
17.2
15
8
2
5.3
14
1.5
2
2.5
R1.5
2.3 1.5 9.5
2.4
8.4 5.9
M3 17.5
3
Mounting Hole Dimensions
2.4 dia.
(depth: 2 min.)
Mounting Bracket
Y92E-C1R6
Material: Stainless steel
(SUS304)
*Provided with E2S-@1@@.
3.1 dia.
2
2
11.3 0.4
2.3
8.1
0.4
2.5
2.5 10.8
11.5
Mounting Hole Dimensions
2.4 dia. (depth: 3 min.)
M3 dia. (depth: 8 min.)
Material: Stainless steel
(SUS304)
* Provided with E2S-@2@@.
Mounting Bracket
Y92E-C2R5
2.4 dia.
0.9
0.3
R1.6
Two, R1.6
1
3
3
5
73.2
2.4
5.3
5.6 *
5 *
17.4
3.2 Four, R1
12
Two, M3
Mounting Hole
Dimensions
* Inside dimension
12.3
2.6
5.5
E2S-Q11
4.2 dia.
Mounting Bracket
Y92E-D1R6
Material: Stainless steel
(SUS304)
Photoelectric Sensor
Accessory is installed
(Example of E2S-Q11)
5
Two, R1.6
R1.6
16
7.8
8 *
7 *
* Inside dimension
1
3.2
22.4
3.2
Four, R1
0.2 17
Two, M3
Mounting Hole
Dimensions
E2S-Q21
8
3.2 3.2
Mounting Bracket
Y92E-D2R5
Material: Stainless steel
(SUS304)
Photoelectric Sensor
Accessory is installed
(Example of E2S-Q21)
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2019.7
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2019 All Right Reserved.