IP67 Sealed
Bi-Color & Tri-Color Options
2 to 28 VDC
200 mm wire terminations
DISTINCTIVE FEATURES
• IP67 sealing option (EN60529)
• Operating Temperature Range: -40 °C to +85 °C ( –40 °F to +185 °F)
• Storage Temperature Range: -55 °C to +100 °C (-67 °F to +212 °F)
ENVIRONMENTAL SPECIFICATIONS
QRM14 series
Ø 14 mm rear panel mount LED indicators
• Max Reverse Voltage: 5 V
• Viewing Angle: 60°
• Life Expectancy: 100,000 hours
• Max Panel Thickness: 3.5 mm
• Torque: 75 cNm (Ø 14 mm)
GENERAL SPECIFICATIONS
• Body: Black plated brass or anodized aluminum
• Lock Washer: Spring steel
• Nut: Black plated brass
• Terminal Seal: Epoxy
• Panel Seal: Nitrile O-ring
• Wires: 22A WG - Approved to UL1007
MATERIALS
The company reserves the right to change specifications without notice.
LED characteristics are dependent upon environmental conditions. Therefore published data
should be considered nominal and subject to variations.
MOUNTING
17,00 0,669 AF 3,00 0,118
M14 x 1,0 THREAD
6,4 [0.251]
O
14,0+0.15/-0.0
[0.551+0.005/-0.0]
1
LED INDICATORS
IND-QRM14-1809
Ø 14 mm rear panel mount LED indicators
QRM14 series
ELECTRICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current
(Min to Max) (Typical All Types)
02 (No Resistor) 1.8 to 3.8 VDC 20 mA max
6 VDC 5.4 to 6.6 VDC 20 mA
12 VDC 10.8 to 13.2 VDC 20 mA
24 VDC 21.6 to 26.4 VDC 20 mA
28 VDC 25.2 to 30.8 VDC 20 mA
* Customer to supply resistor for desired operating
current.
• The operating voltage must not be exceeded by more that
10% as this will result in reduced life expectancy
• Luminous intensity is measured at 20 mA on a discrete led
unless otherwise stated.
• Luminous intensities and color shades of white LEDs may
vary within a batch.
• Luminous intensity will be reduced with lower operating
current.
LED COMPONENT SPECIFICATIONS
Flush Forward Voltage
HE Red 10 mcd 2.0 V
Green 5 mcd 2.2 V
Yellow 4 mcd 2.1 V
Blue 100 mcd 3.3 V
White 150 mcd 3.3 V
Orange 200 mcd 2.2 V
Bi-color (Typical)
(Red/Green) 14/10 mcd 2.0 V/2.2 V
Tri-color (Typical)
(Red/Green/Yellow) 15/10/30 mcd 2.0 V/2.2 V/2.1 V
Bi-color - The color is changed by reversing the polarity of the supply voltage.
Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
STANDARD LED INTENSITY
SUPER BRIGHT LED INTENSITY
HYPER BRIGHT LED INTENSITY
LED COMPONENT SPECIFICATIONS
Flush Forward Voltage
HE Red 2,000 mcd 2.2 V
Green 680 mcd 3.5 V
Yellow 350 mcd 2.3 V
Blue 250 mcd 3.3 V
White 250 mcd 3.3 V
Orange 300 mcd 2.1 V
LED COMPONENT SPECIFICATIONS
Flush Forward Voltage
HE Red 800 mcd 2.0 V
Green 250 mcd 3.2 V
Yellow 250 mcd 2.0 V
Orange 200 mcd 2.1 V
2
LED INDICATORS
BUILD YOUR PART NUMBER
02 no resistor*
06 6 VDC
12 12 VDC
24 24 VDC
28 28 VDC
* please refer to the
forward voltage in
electrical specifications
VOLTAGE
EIP67 (Standard)
SEALING
SERIES
QRM
MOUNTING HOLE
14 Ø14 mm 5Wires
TERMINALS BEZEL FINISH
LED COLOR
RRed
GGreen
YYellow
BBlue
WWhite
OOrange
HR Hyper Bright
Red
HG Hyper Bright
Green
HY Hyper Bright
Yellow
HO Hyper Bright
Orange
SR Super Bright
Red
SG Super Bright
Green
SY Super Bright
Yellow
SB Super Bright
Blue
SW Super Bright
White
SO Super Bright
Orange
RG Red/Green
RY Red/Yellow
GY Green/Yellow
RYG Red/Yellow/
Green
Ø 14 mm rear panel mount LED indicators
QRM14 series
ABOUT THIS SERIES
Notice: please note that not all combinations of above numbers are available.
• Standard wire length is 200 mm, 24 AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths
consult APEM.
• For LEDs with alternate voltages and multi-voltage options consult APEM.
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced.
Bi-color are available up to 28 VDC.
• Take care when soldering (recommended solder temperature 300 °C - 3 sec).
• The Tri-color LED has red and green LEDs when both are connected yellow is produced.
• Standard Tri-color termination is two Anodes (+) and one Cathode (-).
• Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode.
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red.
XX Fixed Light
YY Bi-color
ZZ Tri-color
TYPE OF ILLUMINATION
BBlack
AK Anodized Dark Olive
AN Anodized Black
3
LED INDICATORS
Ø 14 mm rear panel mount LED indicators
QRM14 series
REAR MOUNT - WIRES TERMINALS
- TRI-COLOR LED
REAR MOUNT - WIRES TERMINALS
- SINGLE & BI-COLOR LED
LED INDICATORS
4
