QRM14 series RM -Q O 14 mm rear panel mount LED indicators DISTINCTIVE FEATURES IP67 Sealed Bi-Color & Tri-Color Options 2 to 28 VDC 200 mm wire terminations ENVIRONMENTAL SPECIFICATIONS * IP67 sealing option (EN60529) * Operating Temperature Range: -40 C to +85 C ( -40 F to +185 F) * Storage Temperature Range: -55 C to +100 C (-67 F to +212 F) GENERAL SPECIFICATIONS * Max Reverse Voltage: 5 V * Viewing Angle: 60 * Life Expectancy: 100,000 hours * Max Panel Thickness: 3.5 mm * Torque: 75 cNm (O 14 mm) MATERIALS * Body: Black plated brass or anodized aluminum * Lock Washer: Spring steel * Nut: Black plated brass * Terminal Seal: Epoxy * Panel Seal: Nitrile O-ring * Wires: 22A WG - Approved to UL1007 MOUNTING 17,00 0,669 AF M14 x 1,0 THREAD 3,00 0,118 6,4 [0.251] D IN LED INDICATORS 09 18 14 O14,0+0.15/-0.0 [0.551+0.005/-0.0] The company reserves the right to change specifications without notice. LED characteristics are dependent upon environmental conditions. Therefore published data should be considered nominal and subject to variations. 1 LED INDICATORS QRM14 series O 14 mm rear panel mount LED indicators ELECTRICAL SPECIFICATIONS Voltage STANDARD LED INTENSITY LED COMPONENT SPECIFICATIONS Flush Forward Voltage HE Red 10 mcd 2.0 V Green 5 mcd 2.2 V Yellow 4 mcd 2.1 V Blue 100 mcd 3.3 V White 150 mcd 3.3 V Orange 200 mcd 2.2 V Bi-color (Typical) (Red/Green) 14/10 mcd 2.0 V/2.2 V Tri-color (Typical) (Red/Green/Yellow) 15/10/30 mcd 2.0 V/2.2 V/2.1 V Bi-color - The color is changed by reversing the polarity of the supply voltage. Tri-color - The indicator has red and green LEDs, when both connected yellow is produced. SUPER BRIGHT LED INTENSITY LED COMPONENT SPECIFICATIONS Flush Forward Voltage HE Red 2,000 mcd 2.2 V Green 680 mcd 3.5 V Yellow 350 mcd 2.3 V Blue 250 mcd 3.3 V White 250 mcd 3.3 V Orange 300 mcd 2.1 V HYPER BRIGHT LED INTENSITY LED COMPONENT SPECIFICATIONS Flush Forward Voltage HE Red 800 mcd 2.0 V Green 250 mcd 3.2 V Yellow 250 mcd 2.0 V Orange 200 mcd 2.1 V * The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy * Luminous intensity is measured at 20 mA on a discrete led unless otherwise stated. * Luminous intensities and color shades of white LEDs may vary within a batch. * Luminous intensity will be reduced with lower operating current. 2 Operating Voltage Operating Current (Min to Max) (Typical All Types) 02 (No Resistor) 1.8 to 3.8 VDC 20 mA max 6 VDC 5.4 to 6.6 VDC 20 mA 12 VDC 10.8 to 13.2 VDC 20 mA 24 VDC 21.6 to 26.4 VDC 20 mA 28 VDC 25.2 to 30.8 VDC 20 mA * Customer to supply resistor for desired operating current. O 14 mm rear panel mount LED indicators BUILD YOUR PART NUMBER QRM SERIES TERMINALS MOUNTING HOLE 14 5 O14 mm BEZEL FINISH Wires B XX Fixed Light R Red YY Bi-color G Green ZZ Tri-color Y Yellow B Blue W O White Orange HR Hyper Bright Red HG Hyper Bright Green 6 VDC 12 12 VDC Red/Green 24 24 VDC RY Red/Yellow 28 28 VDC GY Green/Yellow Super Bright White HO Hyper Bright Orange SO Super Bright Orange SR Super Bright Red RG Super Bright Yellow SB Super Bright Blue Anodized Black 06 SW SY AN no resistor* Hyper Bright Yellow Super Bright Green Anodized Dark Olive 02 HY SG AK VOLTAGE LED COLOR TYPE OF ILLUMINATION Black RYG Red/Yellow/ Green SEALING E IP67 (Standard) * please refer to the forward voltage in electrical specifications ABOUT THIS SERIES Notice: please note that not all combinations of above numbers are available. * Standard wire length is 200 mm, 24 AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-) for other wire lengths consult APEM. * For LEDs with alternate voltages and multi-voltage options consult APEM. * Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage another color is produced. Bi-color are available up to 28 VDC. * Take care when soldering (recommended solder temperature 300 C - 3 sec). * The Tri-color LED has red and green LEDs when both are connected yellow is produced. * Standard Tri-color termination is two Anodes (+) and one Cathode (-). * Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode. * Tri-color pins are center (-) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red. 3 LED INDICATORS QRM14 series LED INDICATORS QRM14 series O 14 mm rear panel mount LED indicators REAR MOUNT - WIRES TERMINALS - SINGLE & BI-COLOR LED REAR MOUNT - WIRES TERMINALS - TRI-COLOR LED 4