LM2991
Negative Low Dropout Adjustable Regulator
General Description
The LM2991 is a low dropout adjustable negative regulator
with a output voltage range between −3V to −24V. The
LM2991 provides up to 1A of load current and features a On
/Off pin for remote shutdown capability.
The LM2991 uses new circuit design techniques to provide a
low dropout voltage, low quiescent current and low tempera-
ture coefficient precision reference. The dropout voltage at
1A load current is typically 0.6V and a guaranteed
worst-case maximum of 1V over the entire operating tem-
perature range. The quiescent current is typically 1 mA with
a 1A load current and an input-output voltage differential
greater than 3V. A unique circuit design of the internal bias
supply limits the quiescent current to only 9 mA (typical)
when the regulator is in the dropout mode (V
OUT
−V
IN
≤3V).
The LM2991 is short-circuit proof, and thermal shutdown in-
cludes hysteresis to enhance the reliability of the device
when inadvertently overloaded for extended periods. The
LM2991 is available in 5-lead TO-220 and TO-263 packages
and is rated for operation over the automotive temperature
range of −40˚C to +125˚C. Mil-Aero versions are also avail-
able.
Features
nOutput voltage adjustable from −3V to −24V, typically
−2V to −25V
nOutput current in excess of 1A
nDropout voltage typically 0.6V at 1A load
nLow quiescent current
nInternal short circuit current limit
nInternal thermal shutdown with hysteresis
nTTL, CMOS compatible ON/OFF switch
nFunctional complement to the LM2941 series
Applications
nPost switcher regulator
nLocal, on-card, regulation
nBattery operated equipment
Typical Application
DS011260-1
VOUT =V
REF (1 + R2/R1)
*Required if the regulator is located further than 6 inches from the power supply filter capacitors. A 1 µF solid tantalum or a 10 µF aluminum electrolytic
capacitor is recommended.
**Required for stability. Must be at least a 10 µF aluminum electrolytic or a 1 µF solid tantalum to maintain stability. May be increased without bound to
maintain regulation during transients. Locate the capacitor as close as possible to the regulator. The equivalent series resistance (ESR) is critical, and
should be less than 10Ωover the same operating temperature range as the regulator.
September 2000
LM2991 Negative Low Dropout Adjustable Regulator
© 2000 National Semiconductor Corporation DS011260 www.national.com
Connection Diagrams and Ordering Information
5-Lead TO-220
Straight Leads
DS011260-9
Front View
Order Number LM2991T
See NS Package Number T05A
5-Lead TO-220
Bent, Staggered Leads
DS011260-2
Front View
Order Number LM2991T Flow LB03
See NS Package Number T05D
TO263
5-Lead Surface-Mount Package
DS011260-11
Top View
DS011260-12
Side View
Order Number LM2991S
See NS Package Number TS5B
16-Lead Ceramic Dual-in-Line Package
DS011260-29
Top View
Order Number LM2991J-QMLV
5962-9650501VEA
Order Number LM2991J-QML
5962-9650501QEA
See NS Package Number J16A
16-Lead Ceramic Surface-Mount Package
DS011260-30
Top View
Order Number LM2991WG-QML
5962-9650501QXA
See NS Package Number WG16A
LM2991
www.national.com 2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Voltage −26V to +0.3V
ESD Susceptibility (Note 2) 2 kV
Power Dissipation (Note 3) Internally limited
Junction Temperature (T
Jmax
) 125˚C
Storage Temperature Range −65˚C to +150˚C
Lead Temperature (Soldering, 10 sec.) 230˚C
Operating Ratings (Note 1)
Junction Temperature Range (T
J
) −40˚C to +125˚C
Maximum Input Voltage (Operational) −26V
Electrical Characteristics
V
IN
= −10V, V
O
= −3V, I
O
= 1A, C
O
= 47 µF, R1 = 2.7k, T
J
= 25˚C, unless otherwise specified. Boldface limits apply over
the entire operating junction temperature range.
Parameter Conditions Typical Min Max Units
(Note 4)
Reference Voltage 5 mA ≤I
O
≤1A −1.210 −1.234 −1.186 V
5mA≤I
O
≤1A, −1.27 −1.15 V
V
O
−1V≥V
IN
≥−26V
Output Voltage −2 −3 V
Range V
IN
= −26V −25 −24 V
Line Regulation I
O
= 5 mA, V
O
−1V≥V
IN
≥−26V 0.004 0.04 %/V
Load Regulation 50 mA ≤I
O
≤1A 0.04 0.4 %
Dropout Voltage I
O
= 0.1A, ∆V
O
≤100 mV 0.1 0.2 V
0.3
I
O
= 1A, ∆V
O
≤100 mV 0.6 0.8 V
1
Quiescent Current I
O
≤1A 0.7 5mA
Dropout Quiescent V
IN
=V
O
,I
O
≤1A 16 50 mA
Current
Ripple Rejection V
ripple
= 1 Vrms,
f
ripple
= 1 kHz, 60 50 dB
I
O
=5mA
Output Noise 10 Hz − 100 kHz, I
O
= 5 mA 200 450 µV
ON /OFF Input (V
OUT
: ON) 1.2 0.8 V
Voltage (V
OUT
: OFF) 1.3 2.4
ON /OFF Input V
ON/OFF
= 0.8V (V
OUT
: ON) 0.1 10 µA
Current V
ON/OFF
= 2.4V (V
OUT
: OFF) 40 100
Output Leakage V
IN
= −26V, V
ON/OFF
= 2.4V 60 250 µA
Current V
OUT
=0V
Current Limit V
OUT
= 0V 2 1.5 A
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the deivce is in-
tended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Human body model, 100 pF discharged through a 1.5 kΩresistor.
Note 3: The maximum power dissipation is a function of TJmax,θJA and TA. The maximum allowable power dissipation at any ambient temperature is PD=(T
Jmax
−T
A
)/θJA. If this dissipation is exceeded, the die temperature will rise above 125˚C and the LM2991 will go into thermal shutdown. For the LM2991, the
junction-to-ambient thermal resistance is 53˚C/W for the TO-220, 73˚C/W for the TO-263, and junction-to-case thermal resistance is 3˚C. If the TO-263 package is
used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package. Using 0.5 square inches of copper area,
θJA is 50˚C/W; with 1 square inch of copper area, θJA is 37˚C/W; and with 1.6 or more square inches of copper area, θJA is 32˚C/W.
Note 4: Typicals are at TJ= 25˚C and represent the most likely parametric norm.
LM2991
www.national.com3
Typical Performance Characteristics
Dropout Voltage
DS011260-13
Normalized Output Voltage
DS011260-14
Output Voltage
DS011260-15
Output Noise Voltage
DS011260-16
Quiescent Current
DS011260-17
Maximum Output Current
DS011260-18
Line Transient Response
DS011260-19
Load Transient Response
DS011260-20
Maximum Output Current
DS011260-21
Ripple Rejection
DS011260-22
Output Impedance
DS011260-23
ON /OFF Control Voltage
DS011260-24
LM2991
www.national.com 4
Typical Performance Characteristics (Continued)
Application Hints
External Capacitors
Like any low-dropout regulator, external capacitors are re-
qired to stabilize the control loop. These capacitors must be
correctly selected for proper performance.
INPUT CAPACITOR: An input capacitor is reqiuired if the
regulator is located more than 6″from the input power supply
filter capacitor (or if no other input capaciotr is present).
Asolid Tantalum or ceramic capacitor whose value is at least
1 µF is recommended, but an aluminum electrolytic (≥10 µF)
may be used. However, aluminum electrolytics should not be
used in applications where the ambient temperature can
drop below 0˚C because their internal impedance increases
significantly at cold temperatures.
OUTPUT CAPACITOR: The output capacitor must meet the
ESR limits shown in the graph, which means it must have an
ESR between about 25 mΩand 10Ω.
Asolid Tantalum (value ≥1 µF) is the best choice for the out-
put capacitor. An aluminum electrolytic (≥10 µF) may be
used if the ESR is in the stable range.
It should be noted that the ESR of a typical aluminum elec-
trolytic will increase by as much as 50X as the temperature
is reduced from 25˚C down to −40˚C, while a Tantalum will
exhibit an ESR increase of about 2X over the same range.
For this and other reasons, aluminum electrolytics should
not be used in applications where low operating tempera-
tures occur.
The lower stable ESR limit of 25 mΩmeans that ceramic ca-
pacitors can not be used directly on the output of an LDO. A
ceramic (≥2.2 µF) can be used on the output if some exter-
nal resistance is placed in series with it (1Ωrecommended).
Dielectric types X7R or X5R must be used if the temperature
range of the application varies more than ±25˚ from ambient
to assure the amount of capacitance is sufficient.
CERAMIC BYPASS CAPACITORS:Many designers place
distributed ceramic capacitors whose value is in the range of
1000 pF to 0.1 µF at the power input pins of the IC’s across
a circuit board. These can cause reduced phase margin or
oscillations in LDO regulators.
The advent of multi-layer boards with dedicated power and
ground planes has removed the trace inductance that (previ-
ously) provided the necessary ″decoupling″to shield the out-
put of the LDO from the effects of bypass capacitors.
These capacitors should be avoided if possible, and kept as
far far away from the LDO output as is practical.
Adjust Pin Current
DS011260-25
Low Voltage Behavior
DS011260-26
Maximum Power
Dissipation (TO-220)
DS011260-27
Maximum Power Dissipation
(TO-263) (See Note 3)
DS011260-28
LM2991
www.national.com5
Application Hints (Continued)
MINIMUM LOAD
A minimum load current of 500 µA is required for proper op-
eration. The external resistor divider can provide the mini-
mum load, with the resistor from the adjust pin to ground set
to 2.4 kΩ.
SETTING THE OUTPUT VOLTAGE
The output voltage of the LM2991 is set externally by a resis-
tor divider using the following equation:
V
OUT
=V
REF
x(1+R
2
/R
1
)−(I
ADJ
xR
2
)
where V
REF
= −1.21V. The output voltage can be pro-
grammed within the range of −3V to −24V, typically an even
greater range of −2V to −25V. The adjust pin current is about
60 nA, causing a slight error in the output voltage. However,
using resistors lower than 100 kΩmakes the adjust pin cur-
rent negligible. For example, neglecting the adjust pin cur-
rent, and setting R2 to 100 kΩand V
OUT
to −5V, results in an
output voltage error of only 0.16%.
ON/OFF PIN
The LM2991 regulator can be turned off by applying a TTL or
CMOS level high signal to the ON/OFF pin (see Adjustable
Current Sink Application).
FORCING THE OUTPUT POSITIVE
Due to an internal clamp circuit, the LM2991 can withstand
positive voltages on its output. If the voltage source pulling
the output positive is DC, the current must be limited to 1.5A.
A current over 1.5A fed back into the LM2991 could damage
the device. The LM2991 output can also withstand fast posi-
tive voltage transients up to 26V, without any current limiting
of the source. However, if the transients have a duration of
over 1 ms, the output should be clamped with a Schottky di-
ode to ground.
Typical Applications
Output Capacitor ESR Range
DS011260-5
Fully Isolated Post-Switcher Regulator
DS011260-6
LM2991
www.national.com 6
Typical Applications (Continued)
Adjustable Current Sink
DS011260-10
LM2991
www.national.com7
Equivalent Schematic
DS011260-8
LM2991
www.national.com 8
Physical Dimensions inches (millimeters) unless otherwise noted
5-Lead T0-220, Straight Leads (T)
Order Number LM2991T
NS Package Number T05A
5-Lead T0-220, Bent, Staggered Leads (T)
Order Number LM2991T Flow LBO3
NS Package Number T05D
LM2991
www.national.com9
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
TO-263 5-Lead Plastic Surface Mount Package
Ordering Number LM2991S
NS Package Number TS5B
LM2991
www.national.com 10
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
16-Lead Ceramic Dual-in-Line Package
Order Number LM2991J-QMLV
5962-9650501VEA
Order Number LM2991J-QML
5962-9650501QEA
NS Package Number J16A
LM2991
www.national.com11
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
16-Lead Ceramic Surface-Mount Package
Order Number LM2991WG-QML
5962-9650501QXA
NS Package Number WG16A
LM2991 Negative Low Dropout Adjustable Regulator
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
National P/N LM2991 - Negative Low Dropout Adjustable Regulator
See Wireless Products
Products > Analog - Regulators > Linear Regulators - Low Dropout Voltage > Negative Voltage -
Adjustable > LM2991
LM2991 Product Folder
Negative Low Dropout Adjustable Regulator
Generic P/N 2991
General
Description Features Datasheet Package
& Models Samples
& Pricing
Parametric Table Parametric Table
Multiple Output Capability No
On/Off Pin Yes
Error Flag No
Input Voltage, min (Volt) -26
Input Voltage, max (Volt) .30
Output Current, max 1000 mA
Dropout Voltage, typ (Volt) .60
Quiescent Current, typ (mA) 1
Secondary Ouput Voltage (Volt) -
Secondary Output Current (Amp) -
Output Voltage, min (Volt) -25
Output Voltage, max (Volt) 2
Watchdog -
Datasheet
Title Size in
Kbytes Date View Online Download Receive via
Email
LM2991 Negative Low Dropout Adjustable Regulator 346
Kbytes
14-
Sep-
00 View Online Download Receive via
Email
LM2991 Negative Low Dropout Adjustable Regulator
(JAPANESE)294
Kbytes
View Online
Download
Receive via
Email
LM2991 Mil-Aero Datasheet MNLM2991-X 190
Kbytes View Online Download Receive via
Email
If you have trouble printing or viewing PDF file(s), see Printing Problems.
Package Availability, Models, Samples & Pricing
Part Number Package Status Models Samples &
Electronic
Orders
Budgetary
Pricing Std
Pack
Size
Package
Marking
Type Pins MSL SPICE IBIS Qty $US
each
file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM2991.html (1 of 3) [Aug-09-2002 3:02:34 PM]
National P/N LM2991 - Negative Low Dropout Adjustable Regulator
LM2991T TO 220 5 MSL Full
production N/A N/A
24 Hour
Samples
Buy Now
1K+ $1.2500 rail
of
45
[logo]¢U¢Z¢2¢T
LM2991T
P+
LM2991S TO 263 5MSL Full
production N/A N/A
24 Hour
Samples
Buy Now
1K+ $1.2900 rail
of
45
[logo]¢U¢Z¢2¢T
LM2991S
P+
LM2991SX TO 263 5MSL Full
production N/A N/A
Buy Now
1K+ $1.2900 reel
of
500
[logo]¢U¢Z¢2¢T
LM2991S
P+
5962-
9650501QEA CERDIP 16 MSL Full
production N/A N/A 25+ $11.7000 rail
of
25
[logo]¢Z¢S¢4¢A$E
LM2991J-QML
5962-9650501QEA
5962-
9650501QXA Ceramic
SOIC 16 MSL Full
production N/A N/A
Buy Now
250+ $14.9000 tray
of
42
[logo]¢Z¢S¢4¢A$E
LM2991WG-
QML 5962-
9650501QXA
LM2991J-QMLV CERDIP 16 MSL Preliminary N/A N/A rail
of
N/A
[logo]¢Z¢S¢4¢A$E
LM2991J-QMLV
5962-9650501VEA
RM2991JXQMLV CERDIP 16 MSL Preliminary N/A N/A rail
of
N/A
[logo]¢Z¢S¢4¢A$E
RM2991JXQMLV
LM2991 MD8 Die Full
production N/A N/A
Samples
tray
of
N/A -
LM2991 MDS Die Full
production N/A N/A tray
of
N/A -
LM2991 MW8 Wafer Full
production N/A N/A
wafer
jar
of
N/A
-
General Description
The LM2991 is a low dropout adjustable negative regulator with a output voltage range between -3V to -24V.
The LM2991 provides up to 1A of load current and features a On# /Off pin for remote shutdown capability.
The LM2991 uses new circuit design techniques to provide a low dropout voltage, low quiescent current and
low temperature coefficient precision reference. The dropout voltage at 1A load current is typically 0.6V and
a guaranteed worst-case maximum of 1V over the entire operating temperature range. The quiescent current
is typically 1 mA with a 1A load current and an input-output voltage differential greater than 3V. A unique
circuit design of the internal bias supply limits the quiescent current to only 9 mA (typical) when the
regulator is in the dropout mode (VOUT - VIN < 3V).
The LM2991 is short-circuit proof, and thermal shutdown includes hysteresis to enhance the reliability of the
device when inadvertently overloaded for extended periods. The LM2991 is available in 5-lead TO-220 and
TO-263 packages and is rated for operation over the automotive temperature range of -40°C to +125°C. Mil-
Aero versions are also available.
Features
file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM2991.html (2 of 3) [Aug-09-2002 3:02:34 PM]
National P/N LM2991 - Negative Low Dropout Adjustable Regulator
● Output voltage adjustable from -3V to -24V, typically -2V to -25V
● Output current in excess of 1A
● Dropout voltage typically 0.6V at 1A load
● Low quiescent current
● Internal short circuit current limit
● Internal thermal shutdown with hysteresis
● TTL, CMOS compatible ON#/OFF switch
● Functional complement to the LM2941 series
Applications
● Post switcher regulator
● Local, on-card, regulation
● Battery operated equipment
[Information as of 5-Aug-2002]
Search Design Purchasing Quality Company Home
About Languages . Website Guide . About "Cookies" . National is QS 9000 Certified . Privacy/Security Statement .
Contact Us . Site Terms & Conditions of Use . Copyright 2002 © National Semiconductor Corporation . My Preferences .
Feedback
file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM2991.html (3 of 3) [Aug-09-2002 3:02:34 PM]
