HT1000/2 Series Copper Wire Analyzer HT1000/2 Series Copper Wire Analyzer DESCRIPTION The HT1000/2 series of instruments are high performance, full featured, hand held instruments designed to provide copper wire provisioning and maintenance technicians with the most critical tests at the touch of a button. Durable and water resistant, the HT1000/2 Series is equipped with a highly effective 1/4 VGA LCD screen and a powerful backlight designed to make testing and troubleshooting easier in all work environments. The on-screen menu launches most tests with a single keystroke. Super StressTM reaches beyond standard longitudinal balance testing, identifying even hard to find short loop unbalances. Dual trace TDR is standard, with 12 trace storage and intermittent fault location. The HT1000/2 has user selectable auto tests with an incremental pair testing process. Test for dc and ac volts at the same time; no need to switch between separate screens. Download updates and upload test results quickly and easily via the integrated USB port. VECTORED DSL (Cat. No. HT1000/2VX and HT1000/2VB) Vectored DSL employs line signal coordination and noise cancellation to reduce crosstalk levels and improve line performance. The use of a vectored DSL test instrument is essential to accurately determine data rate potential if the installed network has vectored DSL switch and routing gear. Vectored DSL testing for VDSL2 lines Bonded pair testing Noise finder via a 30 MHz spectrum analyzer Incremental pair test program 200 pair pre-post test storage AC or DC power USB port downloads updates and uploads test results BONDING (Cat. No. HT1000/2CB and HT1000/2VB) Bonded xDSL combines two xDSL lines in order to increase bandwidth potential over a given distance. HT1000/2 offers bonding on selected models as a function for all DSL services from ADSL through to vectored VDSL2. The Megger bonded modem features the latest Broadcom chipset and supports ADSL1, ASDL2, ADSL2+, VDSL2, bonded ADSL and bonded VDSL services. The Broadcom chipset is compatible with a wide range of chipset manufacturers. By using the Megger bonded modem, technicans can switch easily between testing bonded and non-bonded service. FEATURES AND BENEFITS n Easy to navigate and launch testing. Many of the standard 26 tests begin with the push of a single button, either from the numeric keypad or the soft key navigation pad. n Direct access to tests-- no cumbersome menus. Adds to easy training of new technicians. n Fast boot-up time. Unit is ready to test within 9 seconds of turning on. n Voltage, resistance and all standard telecom testing is accessed through the same simple menu layout. n Super Stress test is ten times more sensitive than other technologies available today. What this means is imbalances in twisted pairs can be seen below the 0 dB threshold, zeroing in on those imbalances hiding in shortwire loops. n Automatic Super Stress mode aids technicians in finding invisible faults on short wire loops. HT1000/2 Series Copper Wire Analyzer n All transmission and noise tests for voiceband are included. SPECIFICATIONS n Open meter, which is pinpoint accurate even in the presence of shunt resistance (dirty open), is included. Function Accuracy, whichever is greater AC voltage 300 V AC/DC The built-in TDR locates shorts, crosses, opens, and those short bridge taps that plague VDSL at distances ranging from the end of the test leads to 14.7 km (45,000 ft). It can trace two pairs simultaneously with pair comparison mode to identify potential cable trouble spots. DC voltage 300 V AC/DC Resistance range 0 to 1000 K (2%, 1 ) Leakage 1 to 999 M (3%), 150 V open circuit output Longitudinal balance +30 dBrn to +80 dBrn (2 dBrn) Dual trace TDR allows technician to compare good pair to questionable pair; reads accurately to open or shorted pair. TDR traces can be saved and uploaded to PC for review. Super StressTM -10 dBrn to +80 dBrn (2 dBrn) Load coil detection 0 coil to 4 coils (1 coil) Loop current 0 mA to 100 mA (2%, 1 mA) Auto test / incremental pair test - user can configure up to 8 series of tests to run automatically. This can be used on single, stand-alone pairs or in conjunction with the incremental pair test and bulk pair recovery capability. Power influence +40 dBrnC to +100 dBrnC (2 dBrnC) Loss (Voice Band) -40 dBm to +10 dBm (1 dBm) Open meter 0 m (0 ft) to 900 m (3,000 ft) n n n n Built-in pair recovery program allows technician to gather, store and recall data on defective pairs to compare the condition over time. n The auto test stores test results in a comma delimited format that can be uploaded via the integrated USB port to a customer-driven database. n Download firmware updates via the integrated USB port. n Spectrum analyzer - loss readings up through the VDSL2 range test protocols. n Send and receive frequency spectrum through VDSL2 band. n Spectrum analyzer assists the technician in finding interrupters that cause disruptions to DSL service - will read to VDSL2 band. n n ADSL and VDSL2 with optional card installed, xDSL cards allow technicians to interface with the CO (DSLAM) and measure communication protocols, such as speed upstream and downstream, signal to noise ratios and percent utilization. The built-in modem uses the latest technology to provide full test capabilities for xDSL and vectored DSL without the need for separate instruments. n RFL uses three- or four-wire setup and pinpoints fault size and location with simple temperature and cable gauge adjustments. n Model specific functionality allows the user to tailor their purchase to meet their exact needs. 2%, 1.5 m (5 ft) 900 m (3,000 ft) to 15 km (50,000 ft) (3%) Auto test 7 user-selectable auto test scripts, 200 pair storage, retest capability, Incremental pair testing program ID tone FED ID tone Frequency: 577.5 Hz (1%) Amplitude: 0 dBm, 600 (1 dBm) ID Tone Frequency: Alternating 800 Hz and 1230 Hz (1%) Amplitude: 0 dBm, 600 (1 dBm) Caller ID Yes Wideband tone sent Frequency: 20 KHz to 9 MHz (1%) Amplitude: 0 dBm, 135 (1 dBm) Wideband tone receive Frequency: 20 KHz to 33 MHz Amplitude: -90 dBm, +2 dBm (2 dBm) Wideband loss Frequency: 20 KHz to 33 MHz Amplitude: -90 dBm, +2 dBm (2 dBm) Wideband spectrum analyzer Frequency: 20 KHz to 33 MHz Amplitude: -90 dBm to +10 dBm (2 dBm) -130 dBm/Hz to -30 dBm/Hz (2 dBm/Hz) Impulse noise Amplitude: -45 dBm to +10 dBm (2 dBm) Filters: HDSL, ADSL, ADSL2+ and VDSL2 (20 KHZ to 30 MHz) Voiceband spectrum Frequency: 50 Hz to 4,100 Hz analyzer Amplitude: -64 dBm to 0 dBm (2 dBm) -76 dBm/Hz to -12 dBm/Hz (2 dBm/Hz) HT1000/2 Series Copper Wire Analyzer Resistive fault location Distance to fault: 0 - 3,000 m (10,000 ft) 0.5%, 1 m (3 ft) Maximum measurable fault resistance: 20 MW 3 wire measurements: Distance to strap (length of good wire) Distance to fault Distance from fault to strap calculated 4 wire measurements: Distance to strap (length of faulted wire independent of good wire) Distance to fault Distance from fault to strap measured Gauge pick list: 0.91 mm (19 gauge) 0.64 mm (22 gauge) 0.51 mm (24 gauge) 0.41 mm (26 gauge) Ohms Known distance to strap Temperature adjustment: 0 to 30 C (30 to 110 F) TDR Dual trace, 12 trace memory storage, Automatic pulse width selection, Pair comparison mode, Split/crosstalk mode, Intermittent fault location, Closest range 0 - 8 m (25 ft), Longest range 0 - 14,000 m (45,000 ft) (@VOP = 0.7), Zoom mode Display High resolution, 1/4 VGA graphics with LED backlight Batteries Rechargeable nickel-metal hydride Battery Life Approximately 30 hours typical usage Weight 0.8 kg (28 oz) Dimensions 254 x 114.3 x 63.5 mm (10 x 4.5 x 2.5 in.) Temperature Range Operating: -10 to 55 C (14 to 131 F) Storage: -20 to 65 C (-4 to 149 F) Humidity 95% HT1000/2 "C" Designation Model Specifications In addition to features of HT1000/2"A" designation models Standards compliance ADSL G.dmt G.992 1/2 Annex A, B ADSL2 G. 992.3 Annex A, B, L, M, J ADSL2+ G.992.5 Annex A, B, L, M, J ADSL2+ G.992.5 Amendment 1 ADSL2+ G.998.4 Retransmission-G.INP VDSL G.993.2 VDSL2 G.993.2 ITU-T G.vector (G.993.5) VDSL2 Vectored DSL compatible Bandplans: 8, 12, 17, 30 MHz Profiles: 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a Plan 997, Plan 998 Link stats Modem status Connection type (ADSL, ADSL2, ADSL2+, VDSL, VDSL2) Actual data rate required upstream and downstream % capacity upstream and downstream S/N ratio upstream and downstream Line attenuation upstream and downstream Signal attenuation upstream and downstream Transmit power upstream and downstream Chart/graphic S/N ratio in each bin Protocols Bridge PPPoE PPPoA DHCP Ping test IP address assigned Packet echo statistics Transmitted Received % successfully echoed Round trip time (max, min, average) Output connections POTS, ADSL - VDSL, RT Safety Weather and drop resistant in accordance with MIL-STD-810F IEC61010-1 HT1000/2 "V" Designation Model Specifications In addition to features of HT1000/2"C" designation models Compliance ITU-T G.vector (G.993.5) VDSL2 vectored DSL compatible HT1000/2 "B" Designation Model Specifications In addition to features of HT1000/2 base models specifications ADSL through to vectored VDSL2 G. bond G.998.1 DSL pair bonding HT1000/2 Series Copper Wire Analyzer SELECTION GUIDE HT1000/2AX HT1000/2CX HT1000/2VX HT1000/2CB HT1000/2VB Physical Layer Testing n n n n n Caller ID n n n n n Auto Test n n n n n TDR - Dual Trace n n n n n RFL - 20 MW n n n n n Impulse Noise n n n n n Noise n n n n n Longitudinal Balance (Stress Test) n n n n n Super Stress, -20dB to +30dB n n n n n Ground Resistance n n n n n Incremental Pair Test n n n n n 200 Pair Storage, Pre-Post Test n n n n n Voiceband Spectrum Analyzer n n n n n Wideband Spectrum Analyzer n n n n n FED Control Tones n n n n n Wideband Tone Send n n n n n Wideband Tone Receive n n n n n Wideband Loss n n n n n ADSL n n n n VDSL n n n n IP Ping n n n n n n n Vectoring Bonding n ORDERING INFORMATION Item (Qty) Cat No. Item (Qty) Cat No. HT1000/2AX (English US) 1005-300 Included accessories HT1000/2AX (Spanish Latin) 1005-305 Test lead pair - red/black 1004-180 HT1000/2CX (English US) 1005-307 Test lead pair - yellow/green 1004-181 HT1000/2CX (Spanish Latin) 1005-312 AC battery charger 2001-697 HT1000/2VX (English US) 1005-322 Soft carrying case 1004-182 HT1000/2VX (Spanish Latin) 1005-327 DC battery charger 1004-183 HT1000/2CB (English US) 1005-315 USB cord 1004-610 HT1000/2CB (Spanish Latin) 1005-320 Full set of test leads (red/black and green/yellow) 1004-611 HT1000/2VB (English US) 1005-329 Replacement battery pack 1004-360 HT10002/VB (English Latin) 1005-334 United States 2621 Van Buren Avenue Norristown, PA 19403 USA T 1 866-254-0962 (USA only) T +1 610-676-8500 F +1 610-676-8625 VFCustomerSupport@megger.com (case sensitive email address) UK Archcliffe Road, Dover CT17 9EN England T +44 (0) 1 304 502101 F +44 (0) 1 304 207342 UKsales@megger.com Other technical sales offices Dallas USA, College Station USA, Sydney AUSTRALIA, Danderyd SWEDEN, Ontario CANADA, Trappes FRANCE, Oberursel GERMANY, Aargau SWITZERLAND, Kingdom of BAHRAIN, Mumbai INDIA, Johannesburg SOUTH AFRICA, and Chonburi THAILAND CERTIFICATION ISO Registered to ISO 9001:2008 Cert. no. Q 09250 Registered to ISO 14001-2004 Cert. no. EMS 61597 HT1000/2Series_DS_US_V01 www.megger.com Megger is a registered trademark