HT1000/2 Series
Copper Wire Analyzer
HT1000/2 Series
Copper Wire Analyzer
DESCRIPTION
The HT1000/2 series of instruments are high performance, full
featured, hand held instruments designed to provide copper wire
provisioning and maintenance technicians with the most critical tests
at the touch of a button. Durable and water resistant, the HT1000/2
Series is equipped with a highly effective 1/4 VGA LCD screen and
a powerful backlight designed to make testing and troubleshooting
easier in all work environments.
The on-screen menu launches most tests with a single keystroke.
Super Stress™ reaches beyond standard longitudinal balance testing,
identifying even hard to find short loop unbalances.
Dual trace TDR is standard, with 12 trace storage and intermittent
fault location.
The HT1000/2 has user selectable auto tests with an incremental pair
testing process.
Test for dc and ac volts at the same time; no need to switch between
separate screens.
Download updates and upload test results quickly and easily via the
integrated USB port.
VECTORED DSL
(Cat. No. HT1000/2VX and HT1000/2VB)
Vectored DSL employs line signal coordination and noise cancellation
to reduce crosstalk levels and improve line performance. The use of a
vectored DSL test instrument is essential to accurately determine data
rate potential if the installed network has vectored DSL switch and
routing gear.
BONDING
(Cat. No. HT1000/2CB and HT1000/2VB)
Bonded xDSL combines two xDSL lines in order to increase bandwidth
potential over a given distance. HT1000/2 offers bonding on selected
models as a function for all DSL services from ADSL through to
vectored VDSL2.
The Megger bonded modem features the latest Broadcom chipset and
supports ADSL1, ASDL2, ADSL2+, VDSL2, bonded ADSL and bonded
VDSL services. The Broadcom chipset is compatible with a wide range
of chipset manufacturers.
By using the Megger bonded modem, technicans can switch easily
between testing bonded and non-bonded service.
FEATURES AND BENEFITS
n Easy to navigate and launch testing. Many of the standard
26 tests begin with the push of a single button, either from
the numeric keypad or the soft key navigation pad.
n Direct access to tests — no cumbersome menus. Adds to
easy training of new technicians.
n Fast boot-up time. Unit is ready to test within 9 seconds of
turning on.
n Voltage, resistance and all standard telecom testing is
accessed through the same simple menu layout.
n Super Stress test is ten times more sensitive than
other technologies available today. What this means is
imbalances in twisted pairs can be seen below the 0 dB
threshold, zeroing in on those imbalances hiding in short-
wire loops.
n Automatic Super Stress mode aids technicians in finding
invisible faults on short wire loops.
Vectored DSL testing for VDSL2 lines
Bonded pair testing
Noise finder via a 30 MHz spectrum analyzer
Incremental pair test program
200 pair pre-post test storage
AC or DC power
USB port downloads updates and uploads
test results
HT1000/2 Series
Copper Wire Analyzer
n All transmission and noise tests for voiceband are included.
n Open meter, which is pinpoint accurate even in the presence
of shunt resistance (dirty open), is included.
nThe built-in TDR locates shorts, crosses, opens, and those
short bridge taps that plague VDSL at distances ranging
from the end of the test leads to 14.7 km (45,000 ft). It can
trace two pairs simultaneously with pair comparison mode
to identify potential cable trouble spots.
n Dual trace TDR allows technician to compare good pair to
questionable pair; reads accurately to open or shorted pair.
TDR traces can be saved and uploaded to PC for review.
n Auto test / incremental pair test - user can configure up
to 8 series of tests to run automatically. This can be used
on single, stand-alone pairs or in conjunction with the
incremental pair test and bulk pair recovery capability.
nBuilt-in pair recovery program allows technician to gather,
store and recall data on defective pairs to compare the
condition over time.
nThe auto test stores test results in a comma delimited format
that can be uploaded via the integrated USB port to a
customer-driven database.
n Download firmware updates via the integrated USB port.
n Spectrum analyzer - loss readings up through the VDSL2
range test protocols.
n Send and receive frequency spectrum through VDSL2 band.
n Spectrum analyzer assists the technician in finding
interrupters that cause disruptions to DSL service - will read
to VDSL2 band.
nADSL and VDSL2 with optional card installed, xDSL
cards allow technicians to interface with the CO (DSLAM)
and measure communication protocols, such as speed -
upstream and downstream, signal to noise ratios and
percent utilization.
nThe built-in modem uses the latest technology to provide
full test capabilities for xDSL and vectored DSL without the
need for separate instruments.
nRFL uses three- or four-wire setup and pinpoints fault size
and location with simple temperature and cable gauge
adjustments.
n Model specific functionality allows the user to tailor their
purchase to meet their exact needs.
SPECIFICATIONS
Function Accuracy, whichever is greater
AC voltage 300 V AC/DC
DC voltage 300 V AC/DC
Resistance range 0 Ω to 1000 KΩ (±2%, ±1 Ω)
Leakage 1 Ω to 999 MΩ (±3%), 150 V
open circuit output
Longitudinal balance +30 dBrn to +80 dBrn (±2 dBrn)
Super Stress™ -10 dBrn to +80 dBrn (±2 dBrn)
Load coil detection 0 coil to 4 coils (±1 coil)
Loop current 0 mA to ±100 mA (±2%, ±1 mA)
Power influence +40 dBrnC to +100 dBrnC (±2 dBrnC)
Loss (Voice Band) -40 dBm to +10 dBm (±1 dBm)
Open meter 0 m (0 ft) to 900 m (3,000 ft)
±2%, ±1.5 m (5 ft)
900 m (3,000 ft) to 15 km (50,000 ft)
(±3%)
Auto test 7 user-selectable auto test scripts,
200 pair storage, retest capability,
Incremental pair testing program
ID tone FED ID tone
Frequency: 577.5 Hz (±1%)
Amplitude: 0 dBm, 600 Ω (±1 dBm)
ID Tone
Frequency: Alternating 800 Hz
and 1230 Hz (±1%)
Amplitude: 0 dBm, 600 Ω (±1 dBm)
Caller ID Yes
Wideband tone sent Frequency: 20 KHz to 9 MHz (±1%)
Amplitude: 0 dBm, 135 Ω (±1 dBm)
Wideband tone receive Frequency: 20 KHz to 33 MHz
Amplitude: -90 dBm, +2 dBm
(±2 dBm)
Wideband loss Frequency: 20 KHz to 33 MHz
Amplitude: -90 dBm, +2 dBm
(±2 dBm)
Wideband spectrum Frequency: 20 KHz to 33 MHz
analyzer Amplitude: -90 dBm to +10 dBm
(±2 dBm)
-130 dBm/Hz to -30 dBm/Hz
(±2 dBm/Hz)
Impulse noise Amplitude: -45 dBm to +10 dBm
(±2 dBm)
Filters: HDSL, ADSL, ADSL2+
and VDSL2 (20 KHZ to 30 MHz)
Voiceband spectrum Frequency: 50 Hz to 4,100 Hz
analyzer Amplitude: -64 dBm to 0 dBm
(±2 dBm)
-76 dBm/Hz to -12 dBm/Hz
(±2 dBm/Hz)
HT1000/2 Series
Copper Wire Analyzer
Resistive fault location Distance to fault: 0 - 3,000 m
(10,000 ft) ±0.5%, ±1 m (3 ft)
Maximum measurable fault
resistance: 20 MW
3 wire measurements:
Distance to strap (length of good
wire)
Distance to fault
Distance from fault to strap calculated
4 wire measurements:
Distance to strap (length of faulted
wire independent of good wire)
Distance to fault
Distance from fault to strap measured
Gauge pick list:
0.91 mm (19 gauge)
0.64 mm (22 gauge)
0.51 mm (24 gauge)
0.41 mm (26 gauge)
Ohms
Known distance to strap
Temperature adjustment: 0° to 30° C
(30° to 110° F)
TDR Dual trace, 12 trace memory storage,
Automatic pulse width selection,
Pair comparison mode, Split/crosstalk
mode, Intermittent fault location,
Closest range 0 – 8 m (25 ft),
Longest range 0 – 14,000 m (45,000 ft)
(@VOP = 0.7), Zoom mode
Display High resolution, ¼ VGA graphics with
LED backlight
Batteries Rechargeable nickel-metal hydride
Battery Life Approximately 30 hours typical usage
Weight 0.8 kg (28 oz)
Dimensions 254 x 114.3 x 63.5 mm
(10 x 4.5 x 2.5 in.)
Temperature Range Operating: -10° to 55° C (14° to 131° F)
Storage: -20° to 65° C (-4° to 149° F)
Humidity 95%
HT1000/2 “C” Designation Model Specifications
In addition to features of HT1000/2”A” designation models
Standards compliance ADSL G.dmt G.992 1/2 Annex A, B
ADSL2 G. 992.3 Annex A, B, L, M, J
ADSL2+ G.992.5 Annex A, B, L, M, J
ADSL2+ G.992.5 Amendment 1
ADSL2+ G.998.4
Retransmission-G.INP
VDSL G.993.2
VDSL2 G.993.2
ITU-T G.vector (G.993.5)
VDSL2 Vectored DSL compatible
Bandplans: 8, 12, 17, 30 MHz
Profiles: 8a, 8b, 8c, 8d, 12a, 12b,
17a, 30a
Plan 997, Plan 998
Link stats Modem status
Connection type (ADSL, ADSL2,
ADSL2+, VDSL, VDSL2)
Actual data rate required upstream
and downstream
% capacity upstream and downstream
S/N ratio upstream and downstream
Line attenuation upstream and
downstream
Signal attenuation upstream and
downstream
Transmit power upstream and down-
stream
Chart/graphic S/N ratio in each bin
Protocols Bridge
PPPoE
PPPoA
DHCP
Ping test IP address assigned
Packet echo statistics
Transmitted
Received
% successfully echoed
Round trip time (max, min, average)
Output connections POTS, ADSL - VDSL, RT
Safety Weather and drop resistant in
accordance with MIL-STD-810F
IEC61010-1
HT1000/2 “V” Designation Model Specifications
In addition to features of HT1000/2”C” designation models
Compliance ITU-T G.vector (G.993.5)
VDSL2 vectored DSL compatible
HT1000/2 “B” Designation Model Specifications
In addition to features of HT1000/2 base models specifications
ADSL through to vectored VDSL2 G. bond G.998.1 DSL pair bonding
CERTIFICATION ISO
Registered to ISO 9001:2008 Cert. no. Q 09250
Registered to ISO 14001-2004 Cert. no. EMS 61597
HT1000/2Series_DS_US_V01
www.megger.com
Megger is a registered trademark
ORDERING INFORMATION
Item (Qty) Cat No.
HT1000/2AX (English US) 1005-300
HT1000/2AX (Spanish Latin) 1005-305
HT1000/2CX (English US) 1005-307
HT1000/2CX (Spanish Latin) 1005-312
HT1000/2VX (English US) 1005-322
HT1000/2VX (Spanish Latin) 1005-327
HT1000/2CB (English US) 1005-315
HT1000/2CB (Spanish Latin) 1005-320
HT1000/2VB (English US) 1005-329
HT10002/VB (English Latin) 1005-334
UK
Archcliffe Road, Dover
CT17 9EN England
T +44 (0) 1 304 502101
F +44 (0) 1 304 207342
UKsales@megger.com
UNITED STATES
2621 Van Buren Avenue
Norristown, PA 19403 USA
T 1 866-254-0962 (USA only)
T +1 610-676-8500
F +1 610-676-8625
VFCustomerSupport@megger.com
(case sensitive email address)
OTHER TECHNICAL SALES OFFICES
Dallas USA, College Station USA,
Sydney AUSTRALIA, Danderyd
SWEDEN, Ontario CANADA, Trappes
FRANCE, Oberursel GERMANY, Aargau
SWITZERLAND, Kingdom of BAHRAIN,
Mumbai INDIA, Johannesburg SOUTH
AFRICA, and Chonburi THAILAND
SELECTION GUIDE
HT1000/2AX HT1000/2CX HT1000/2VX HT1000/2CB HT1000/2VB
Physical Layer Testing n n n n n
Caller ID n n n n n
Auto Test n n n n n
TDR - Dual Trace n n n n n
RFL - 20 MWn n n n n
Impulse Noise n n n n n
Noise n n n n n
Longitudinal Balance (Stress Test) n n n n n
Super Stress, -20dB to +30dB n n n n n
Ground Resistance n n n n n
Incremental Pair Test n n n n n
200 Pair Storage, Pre-Post Test n n n n n
Voiceband Spectrum Analyzer n n n n n
Wideband Spectrum Analyzer n n n n n
FED Control Tones n n n n n
Wideband Tone Send n n n n n
Wideband Tone Receive n n n n n
Wideband Loss n n n n n
ADSL n n n n
VDSL n n n n
IP Ping n n n n
Vectoring n n
Bonding n n
HT1000/2 Series
Copper Wire Analyzer
Item (Qty) Cat No.
Included accessories
Test lead pair - red/black 1004-180
Test lead pair - yellow/green 1004-181
AC battery charger 2001-697
Soft carrying case 1004-182
DC battery charger 1004-183
USB cord 1004-610
Full set of test leads (red/black and green/yellow) 1004-611
Replacement battery pack 1004-360
