PIC16(L)F18424/44 14/20-Pin Full-Featured, Low Pin Count Microcontrollers with XLP Description PIC16(L)F184XX microcontrollers feature Intelligent Analog, Core Independent Peripherals (CIPs) and communication peripherals combined with eXtreme Low-Power (XLP) for a wide range of general purpose and low-power applications. Features such as a 12-bit Analog-to-Digital Converter with Computation (ADC2), Memory Access Partitioning (MAP), the Device Information Area (DIA), Powersaving operating modes, and Peripheral Pin Select (PPS), offer flexible solutions for a wide variety of custom applications. Core Features * * * * * * * * * * * * C Compiler Optimized RISC Architecture Only 50 Instructions Operating Speed: - DC - 32 MHz clock input - 125 ns minimum instruction cycle Interrupt Capability 16-Level Deep Hardware Stack Timers: - Up to two 24-bit timers - Up to four 8-bit timers - Up to four 16-bit timers Low-Current Power-on Reset (POR) Configurable Power-up Timer (PWRT) Brown-out Reset (BOR) Low-Power BOR (LPBOR) Option Windowed Watchdog Timer (WWDT): - Variable prescaler selection - Variable window size selection - Configurable in hardware (Configuration Words) and/or software Programmable Code Protection Memory * * Up to 28 KB Program Flash Memory Up to 2 KB Data SRAM Memory (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 1 PIC16(L)F18424/44 * * * * * 256B Data EEPROM Direct, Indirect and Relative Addressing modes Memory Access Partition (MAP): - Write-protect - Customizable partition Device Information Area (DIA) Device Configuration Information (DCI) Operating Characteristics * * Operating Voltage Range: - 1.8V to 3.6V (PIC16LF184XX) - 2.3V to 5.5V (PIC16F184XX) Temperature Range: - Industrial: -40C to 85C - Extended: -40C to 125C Power-Saving Operation Modes * * * * * Doze: CPU and Peripherals Running at Different Cycle Rates (typically CPU is lower) Idle: CPU Halted While Peripherals Operate Sleep: Lowest Power Consumption Peripheral Module Disable (PMD): - Ability to selectively disable hardware module to minimize active power consumption of unused peripherals Extreme Low-Power mode (XLP) - Sleep: 500 nA typical @ 1.8V - Sleep and Watchdog Timer: 900 nA typical @ 1.8V eXtreme Low-Power (XLP) Features * * * Sleep mode: 50 nA @ 1.8, typical Watchdog Timer: 500 nA @ 1.8V, typical Secondary Oscillator: 500 nA @ 32 kHz * Operating Current: - 8 uA @ 32 kHz, 1.8V, typical - 32 uA/MHz @ 1.8V, typical Digital Peripherals * * Configurable Logic Cell (CLC): - 4 CLCs - Integrated combinational and sequential logic Complementary Waveform Generator (CWG): - 2 CWGs (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 2 PIC16(L)F18424/44 * * * * * * * * - Rising and falling edge dead-band control - Full-bridge, half-bridge, 1-channel drive - Multiple signal sources Capture/Compare/PWM (CCP) modules: - 4 CCPs - 16-bit resolution for Capture/Compare modes - 10-bit resolution for PWM mode Pulse-Width Modulators (PWM): - 2 10-bit PWMs Numerically Controlled Oscillator (NCO): - Precision linear frequency generator (@50% duty cycle) with 0.0001% step size of source input clock - Input Clock: 0 Hz < fNCO < 32 MHz - Resolution: fNCO/220 Peripheral Pin Select (PPS): - I/O pin remapping of digital peripherals Serial Communications: - EUSART * 1 EUSART(s) * RS-232, RS-485, LIN compatible * Auto-Baud Detect, Auto-wake-up on Start. - Master Synchronous Serial Port (MSSP) * 1 MSSP(s) * SPI TM * I2C, SMBus and PMBus compatible Data Signal Modulator (DSM): - Modulates a carrier signal with digital data to create custom carrier synchronized output waveforms Up to 18 I/O Pins: - Individually programmable pull-ups - Slew rate control - Interrupt-on-change with edge-select - Input level selection control (ST or TTL) - Digital open-drain enable Timer modules: - Timer0: * 8/16-bit timer/counter * Synchronous or asynchronous operation * Programmable prescaler/postscaler * Time base for capture/compare function - Timer1/3/5 with gate control: * 16-bit timer/counter * Programmable internal or external clock sources * Multiple gate sources (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 3 PIC16(L)F18424/44 - - * Multiple gate modes * Time base for capture/compare function Timer2/4/6 with Hardware Limit Timer: * 8-bit timers * Programmable prescaler/postscaler * Time base for PWM function * Hardware Limit (HLT) and one-shot extensions * Selectable clock sources Signal Measurement Timer (SMT) * 1 SMT(s) * 24-bit timer/counter with programmable prescaler Analog Peripherals * * * * * * Analog-to-Digital Converter with Computation (ADC2): - 12-bit with up to 17 external channels - Conversion available during Sleep - Automated post-processing - Automated math functions on input signals: * Averaging, filter calculations, oversampling and threshold comparison - Integrated charge pump for low-voltage operation - CVD support Zero-Cross Detect (ZCD): - AC high voltage zero-crossing detection for simplifying TRIAC control - Synchronized switching control and timing Temperature Sensor Circuit Comparator: - 2 Comparators - Fixed Voltage Reference at (non)inverting input(s) - Comparator outputs externally accessible Digital-to-Analog Converter (DAC): - 5-bit resolution, rail-to-rail - Positive Reference Selection - Unbuffered I/O pin output - Internal connections to ADCs and comparators Fixed Voltage Reference (FVR) module: - 1.024V, 2.048V and 4.096V output levels Flexible Oscillator Structure * * High-Precision Internal Oscillator: - Software-selectable frequency range up to 32 MHz - 2% at calibration (nominal) 4x PLL for use with External Sources: - up to 32 MHz (4-8 MHz input) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 4 PIC16(L)F18424/44 * * * * 2x PLL for use with the HFINTOSC: - up to 32 MHz Low-Power Internal 31 kHz Oscillator (LFINTOSC) External 32.768 kHz Crystal Oscillator (SOCS) External Oscillator Block with: - Three crystal/resonator modes up to 20 MHz - Three external clock modes up to 32 MHz - Fail-Safe Clock Monitor - * Detects clock source failure Oscillator Start-up Timer (OST) * Ensures stability of crystal oscillator sources PIC16(L)F184XX Family Types CCP PWM NCO EUSART MSSP (I2C/SPI) CLC DSM PPS XLP PMD Windowed Watchdog Timer Memory Access Partition Device Information Area Debug(1) 1 1 1 4 1 Y Y Y Y Y Y I PIC16(L)F18444 4096 7 256 512 18 17 1 2 2 1 4/4 4 2 1 1 1 4 1 Y Y Y Y Y Y I Timers (8/16-bit) CWG 2 Clock Ref Comparators 1 4/4 4 12-bit ADC2 (ch) 2 I/O's(2) 2 Data SRAM (bytes) PIC16(L)F18424 4096 7 256 512 12 11 1 Device 5-bit DAC Data Memory (EEPROM) (bytes) Program Flash Memory (Kbytes) Program Flash Memory (Words) Table 1. Devices Included In This Data Sheet Note: 1. I - Debugging integrated on-chip. 2. One pin is input-only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 5 PIC16(L)F18424/44 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18426 16384 28 256 2048 12 11 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18445 8192 14 256 1024 18 17 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18446 16384 28 256 2048 18 17 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18455 8192 14 256 1024 26 24 1 2 3 1 4/4 5 2 1 2 2 4 1 Y Y Y Y Y Y I PIC16(L)F18456 16384 28 256 2048 26 24 1 2 3 1 4/4 5 2 1 2 2 4 1 Y Y Y Y Y Y I Data Sheet Index: 1. 2. 3. DS(40002000) Data Sheet, 14/20-Pin Full-Featured, Low Pin Count Microcontrollers with XLP DS(40002002) Data Sheet, 14/20-Pin Full-Featured, Low Pin Count Microcontrollers with XLP DS(TBD) Data Sheet, 28-Pin Full-Featured, Low Pin Count Microcontrollers with XLP Packages Packages PDIP SOIC PIC16(L)F18424 PIC16(L)F18444 SSOP TSSOP UQFN (4x4) Note: Pin details are subject to change. Important: For other small form-factor package availability and marking information, visit www.microchip.com/ packaging or contact your local sales office. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 6 Debug(1) DSM Device Information Area CLC Memory Access Partition MSSP (I2C/SPI) Windowed Watchdog Timer EUSART 1 PMD NCO 2 XLP PWM 1 4/4 4 PPS CCP Timers (8/16-bit) CWG 2 Clock Ref Comparators 2 I/O's(2) PIC16(L)F18425 8192 14 256 1024 12 11 1 Device 5-bit DAC 12-bit ADC2 (ch) Data SRAM (bytes) Data Memory (EEPROM) (bytes) Program Flash Memory (Words) Program Flash Memory (Kbytes) Table 2. Devices Not Included In This Data Sheet PIC16(L)F18424/44 Pin Diagrams 1 14/16-Pin Diagrams Figure 1. 14-Pin PDIP, SOIC, TSSOP Rev. 00-000014A 6/21/2017 VDD 1 RA5 2 14 13 RA4 3 12 RA1/ICSPCLK VSS RA0/ICSPDAT MCLR/VPP/RA3 4 11 RA2 RC5 5 10 RC0 RC4 6 9 RC1 RC3 7 8 RC2 Figure 2. 16-Pin UQFN (4x4) NC VSS NC VDD Rev. 00-000016A 6/21/2017 16 15 14 13 RA5 1 12 RA0/ICSPDAT RA4 2 11 RA1/ICSPCLK 5 6 7 8 RC1 9 RC0 RC2 RC5 4 RC3 10 RA2 RC4 MCLR/VPP/RA3 3 Note: It is recommended that the exposed bottom pad be connected to VSS. Related Links 14/16-Pin Allocation Table 2 20-Pin Diagrams Figure 3. 20-Pin PDIP, SOIC, SSOP Rev. 00-000020A 6/21/2017 (c) 2018 Microchip Technology Inc. VDD 1 RA5 2 20 VSS 19 RA0/ICSPDAT RA4 3 18 RA1/ICSPCLK MCLR/VPP/RA3 4 17 RA2 RC5 5 16 RC0 RC4 6 15 RC1 RC3 7 14 RC2 RC6 8 13 RB4 RC7 9 12 RB5 RB7 10 11 RB6 Datasheet Preliminary DS40002000A-page 7 PIC16(L)F18424/44 Figure 4. 20-Pin UQFN (4x4) RA0/ICSPDAT VSS VDD RA5 RA4 Rev. 00-000020B 6/21/2016 20 19 18 17 16 15 RA1/ICSPCLK MCLR/VPP/RA3 1 RC4 3 13 RC0 RC3 4 12 RC1 RC6 5 11 RC2 8 9 10 RB4 7 RB5 RC7 6 RB6 14 RA2 RB7 RC5 2 Note: It is recommended that the exposed bottom pad be connected to VSS. Related Links 20-Pin Allocation Table Pin Allocation Tables RA0 13 12 ANA0 -- C1IN0+ -- DAC1OUT1 MDSRC(1) -- -- -- -- SS2(1) Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 16-pin UQFN 14/16-Pin Allocation Table 14-pin PDIP/SOIC/TSSOP I/O 1 ICDDAT -- -- -- -- IOCA0 Y ICSPDAT C1IN0 RA1 12 11 ANA1 ADCVREF+ ICDCLK -- DAC1VREF+ -- -- -- -- -- -- -- -- -- -- IOCA1 Y C2IN0- RA2 11 10 RA3 4 3 ICSPCLK CWG1IN(1) ANA2 ADCVREF- -- -- DAC1VREF- -- T0CKI(1) CCP3IN(1) -- -- -- -- -- -- -- T6IN(1) -- -- CWG2IN(1) -- ZCD1 -- -- -- IOCA2 Y -- -- -- -- -- IOCA3 Y INT(1) MCLR -- VPP CLKOUT T1G(1) RA4 3 2 ANA4 -- -- -- -- -- SMT1WIN(1) -- -- -- -- -- -- -- -- IOCA4 Y SOSCO OSC2 T1CKI(1) RA5 2 1 ANA5 -- -- -- -- -- T2IN(1) CLKIN -- -- -- -- -- -- CLCIN3(1) -- IOCA5 Y SMT1SIG(1) (c) 2018 Microchip Technology Inc. Datasheet Preliminary SOSCI OSC1 DS40002000A-page 8 Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator 9 Reference 16-pin UQFN 10 ADC 14-pin PDIP/SOIC/TSSOP I/O PIC16(L)F18424/44 SCK1(1) RC0 ANC0 -- C2IN0+ -- -- -- T5CKI(1) -- -- -- -- -- -- -- IOCC0 Y -- -- -- CLCIN2(1) -- IOCC1 Y -- SCL1(1,3,4) SDI1(1) C1IN1RC1 9 8 ANC1 -- -- -- -- T4IN(1) CCP4IN(1) -- -- SDA1(1,3,4) C2IN1- ANC2 RC2 8 7 C1IN2-- ADACT(1) -- -- MDCARL(1) -- -- -- -- -- -- -- -- -- IOCC2 Y -- -- -- -- T5G(1) CCP2IN(1) -- -- SS1(1) -- -- CLCIN0(1) -- IOCC3 Y -- -- -- -- T3G(1) -- -- -- CK1(1,3) CLCIN1(1) -- IOCC4 Y -- -- -- IOCC5 Y -- C2IN2- C1IN3RC3 7 6 ANC3 -- C2IN3- SCK2(1,5) RC4 6 5 ANC4 -- -- -- SCL2(1,3,4,5) SDI2(1,5) RC5 5 4 ANC5 -- -- -- -- MDCARH(1) T3CKI(1) CCP1IN(1) -- -- RX1(1) -- SDA2(1,3,4,5) DT1(1,3) VDD 1 16 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- VDD VSS 14 13 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- VSS CWG1A SDO1 -- DSM1OUT TMR0OUT CCP1OUT PWM6OUT -- DT1(3) CLC1OUT CLKR -- -- -- CWG2A SDO2 CWG1B SCK1 -- CK1(3) CLC2OUT -- -- -- -- CWG2B SCK2 CWG1C SCL1(3) -- TX1 CLC3OUT -- -- -- -- CWG2C SCL2(3) CWG1D SDA1(3) -- -- CLC4OUT -- -- -- -- CWG2D SDA2(3) -- -- ADCGRDA -- -- ADCGRDB -- -- C1OUT NCO1OUT C2OUT -- -- -- -- CCP2OUT PWM7OUT OUT(2) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- CCP3OUT CCP4OUT -- -- Note: 1. This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins. 2. All digital output signals shown in these rows are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options. 3. This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers. 4. These pins may be configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or SMBus input buffer thresholds. 5. MSSP2 is not available on the PIC16(L)F18424 or PIC16(L)F18444 devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 9 PIC16(L)F18424/44 Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 20-pin UQFN 20-Pin Allocation Table 20-pin PDIP/SOIC/TSSOP I/O 2 ICDDAT/ RA0 19 16 ANA0 -- C1IN0+ -- DAC1OUT1 -- -- -- -- -- -- -- -- -- -- IOCA0 Y ICSPDAT RA1 18 15 ANA1 ADCVREF + C1IN0-- C2IN0- ICDCLK/ DAC1VREF MDSRC(1) + -- -- -- -- SS2(1) -- -- -- -- IOCA1 Y ICSPCLK CWG1IN(1) RA2 17 14 ANA2 ADCVREF- -- -- DAC1VREF- T0CKI(1) -- -- -- -- ZCD1 -- CLCIN0(1) -- IOCA2 Y -- -- -- -- -- IOCA3 Y INT(1) CWG2IN(1) MCLR RA3 4 1 -- -- -- -- -- -- -- -- -- -- VPP CLKOUT T1G(1) RA4 3 20 ANA4 -- -- -- -- CCP4IN(1) -- -- -- -- -- -- -- -- IOCA4 Y SOSCO SMT1WIN(1) OSC2 T1CKI(1) RA5 2 19 ANA5 -- -- -- -- T2IN(1) -- CLKIN -- -- -- -- -- -- -- -- IOCA5 Y SMT1SIG(1) SOSCI OSC1 SDI1(1) RB4 13 10 ANB4 -- -- -- -- T5G(1) -- -- -- -- -- -- CLCIN2(1) -- IOCB4 Y -- CLCIN3(1) -- IOCB5 Y -- SDA1(1,3,4) SCK2(1,5) RB5 12 9 ANB5 -- -- -- -- -- -- CCP3IN(1) -- -- RX1(1) -- SCL2(1,3,4,5) DT1(1,3) SCK1(1) RB6 11 8 ANB6 -- -- -- -- -- -- -- -- -- -- -- -- -- IOCB6 Y -- -- CK1(1,3) -- -- IOCB7 Y -- SCL1(1,3,4) SDI2(1,5) RB7 10 7 ANB7 -- -- -- -- T6IN(1) -- -- -- -- SDA2(1,3,4,5) T3CKI(1) RC0 16 13 ANC0 -- C2IN0+ -- -- -- -- -- -- -- -- -- -- -- IOCC0 Y -- T3G(1) C1IN1RC1 15 12 ANC1 -- -- -- -- -- -- -- -- -- -- -- -- -- IOCC1 Y -- -- -- MDCARL(1) T5CKI(1) -- -- -- -- -- -- -- -- IOCC2 Y -- C2IN1- RC2 14 11 ANC2 -- C1IN2- (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 10 ADACT(1) Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 20-pin UQFN 20-pin PDIP/SOIC/TSSOP I/O PIC16(L)F18424/44 C2IN2- C1IN3RC3 7 4 ANC3 -- -- -- -- -- CCP2IN(1) -- -- -- -- -- CLCIN1(1) -- IOCC3 Y -- -- C2IN3RC4 6 3 ANC4 -- -- -- -- -- -- -- -- -- -- -- -- -- -- IOCC4 Y RC5 5 2 ANC5 -- -- -- -- MDCARH(1) T4IN(1) CCP1IN(1) -- -- -- -- -- -- IOCC5 Y -- RC6 8 5 ANC6 -- -- -- -- -- -- -- -- -- -- SS1(1) -- -- -- -- IOCC6 Y -- 6 IOCC7 Y RC7 9 ANC7 -- -- -- -- -- -- -- -- -- -- -- -- -- -- VDD 1 18 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- VDD VSS 20 17 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- VSS CWG1A SDO1 -- DSM1OUT CWG2A SDO2 CWG1B SCK1 CWG2B SCK2 CWG1C SCL1(3) CWG2C SCL2(3) CWG1D SDA1(3) CWG2D SDA2(3) -- -- ADCGRDA -- -- ADCGRDB -- -- C1OUT NCO1OUT C2OUT -- -- -- TMR0OUT CCP1OUT PWM6OUT -- CCP2OUT PWM7OUT -- -- DT1(3) CLC1OUT CLKR -- -- -- -- CK1(3) CLC2OUT -- -- -- -- OUT(2) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- CCP3OUT CCP4OUT -- -- -- TX1 CLC3OUT -- -- -- -- -- -- CLC4OUT -- -- -- -- Note: 1. This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins. 2. All digital output signals shown in these rows are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options. 3. This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers. 4. These pins may be configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or SMBus input buffer thresholds. 5. MSSP2 is not available on the PIC16(L)F18424 or PIC16(L)F18444 devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 11 PIC16(L)F18424/44 Table of Contents Description.......................................................................................................................1 Core Features..................................................................................................................1 Memory............................................................................................................................1 Operating Characteristics................................................................................................ 2 Power-Saving Operation Modes......................................................................................2 eXtreme Low-Power (XLP) Features...............................................................................2 Digital Peripherals........................................................................................................... 2 Analog Peripherals.......................................................................................................... 4 Flexible Oscillator Structure.............................................................................................4 PIC16(L)F184XX Family Types....................................................................................... 5 Packages.........................................................................................................................6 Pin Diagrams................................................................................................................... 7 Pin Allocation Tables....................................................................................................... 8 1. Device Overview......................................................................................................15 2. Guidelines for Getting Started with PIC16(L)F18424/44 Microcontrollers...............21 3. Enhanced Mid-Range CPU..................................................................................... 26 4. Device Configuration............................................................................................... 28 5. Device Information Area.......................................................................................... 41 6. Device Configuration Information............................................................................ 44 7. Memory Organization.............................................................................................. 45 8. Resets..................................................................................................................... 82 9. Oscillator Module (with Fail-Safe Clock Monitor).....................................................96 10. Interrupts................................................................................................................119 11. Power-Saving Operation Modes............................................................................147 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 12 PIC16(L)F18424/44 12. (WWDT) Windowed Watchdog Timer....................................................................157 13. (NVM) Nonvolatile Memory Control.......................................................................169 14. I/O Ports................................................................................................................ 191 15. (PPS) Peripheral Pin Select Module......................................................................220 16. (PMD) Peripheral Module Disable......................................................................... 231 17. Interrupt-on-Change.............................................................................................. 241 18. (FVR) Fixed Voltage Reference.............................................................................253 19. Temperature Indicator Module...............................................................................258 20. (ADC2) Analog-to-Digital Converter with Computation Module............................. 261 21. (DAC) 5-Bit Digital-to-Analog Converter Module................................................... 309 22. Numerically Controlled Oscillator (NCO) Module.................................................. 315 23. (CMP) Comparator Module................................................................................... 326 24. Timer0 Module.......................................................................................................339 25. Timer1 Module with Gate Control.......................................................................... 348 26. Timer2 Module.......................................................................................................368 27. (ZCD) Zero-Cross Detection Module.....................................................................395 28. CCP/PWM Timer Resource Selection................................................................... 403 29. Capture/Compare/PWM Module........................................................................... 407 30. (PWM) Pulse-Width Modulation............................................................................ 422 31. (CWG) Complementary Waveform Generator Module..........................................430 32. (DSM) Data Signal Modulator Module...................................................................460 33. (CLC) Configurable Logic Cell...............................................................................473 34. Reference Clock Output Module........................................................................... 495 35. (MSSP) Master Synchronous Serial Port Module................................................. 501 36. (EUSART) Enhanced Universal Synchronous Asynchronous Receiver Transmitter ...............................................................................................................................566 37. (SMT) Signal Measurement Timer.........................................................................601 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 13 PIC16(L)F18424/44 38. Register Summary.................................................................................................628 39. In-Circuit Serial ProgrammingTM (ICSPTM) .............................................................659 40. Instruction Set Summary....................................................................................... 662 41. Development Support............................................................................................685 42. Electrical Specifications.........................................................................................690 43. DC and AC Characteristics Graphs and Tables.................................................... 727 44. Packaging Information...........................................................................................729 45. Revision A (02/2018)............................................................................................. 751 The Microchip Web Site.............................................................................................. 752 Customer Change Notification Service........................................................................752 Customer Support....................................................................................................... 752 Product Identification System...................................................................................... 753 Microchip Devices Code Protection Feature............................................................... 753 Legal Notice.................................................................................................................754 Trademarks................................................................................................................. 754 Quality Management System Certified by DNV...........................................................755 Worldwide Sales and Service......................................................................................756 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 14 PIC16(L)F18424/44 Device Overview 1. Device Overview This document contains device-specific information for the following devices: * PIC16F18424 * PIC16LF18424 * PIC16F18444 * PIC16LF18444 1.1 New Core Features 1.1.1 XLP Technology All of the devices in the PIC16(L)F184XX family incorporate a range of features that can significantly reduce power consumption during operation. Key items include: * * * * 1.1.2 Alternate Run Modes: By clocking the controller from the secondary oscillator or the internal oscillator block, power consumption during code execution can be reduced by as much as 90%. Multiple Idle Modes: The controller can also run with its CPU core disabled but the peripherals still active. In these states, power consumption can be reduced even further, to as little as 4% of normal operation requirements. On-the-Fly Mode Switching: The power-managed modes are invoked by user code during operation, allowing the user to incorporate power-saving ideas into their application's software design. Peripheral Module Disable: Modules that are not being used in the code can be selectively disabled using the PMD module. This further reduces the power consumption. Multiple Oscillator Options and Features All of the devices in the PIC16(L)F184XX family offer several different oscillator options. The PIC16(L)F184XX family can be clocked from several different sources: * * * * * * HFINTOSC - 1-32 MHz precision digitally controlled internal oscillator LFINTOSC - 31 kHz internal oscillator EXTOSC - External clock (EC) - Low-power oscillator (LP) - Medium-power oscillator (XT) - High-power oscillator (HS) SOSC - Secondary oscillator circuit optimized for 32 kHz clock crystals A Phase Lock Loop (PLL) frequency multiplier (2x/4x) is available to the External Oscillator modes enabling clock speeds of up to 32 MHz Fail-Safe Clock Monitor: This option constantly monitors the main clock source against a reference signal provided by the LFINTOSC. If a clock failure occurs, the controller is switched to the internal oscillator block, allowing for continued operation or a safe application shutdown. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 15 PIC16(L)F18424/44 Device Overview 1.2 Other Special Features * * * * * 1.3 12-bit A/D Converter with Computation: This module incorporates programmable acquisition time, allowing for a channel to be selected and a conversion to be initiated without waiting for a sampling period and thus, reduce code overhead. It has a new module called ADC2 with computation features, which provides a digital filter and threshold interrupt functions. Memory Endurance: The Flash cells for both program memory and data EEPROM are rated to last for many thousands of erase/write cycles - up to 10K for program memory and 100K for EEPROM. Data retention without refresh is conservatively estimated to be greater than 40 years. Self-programmability: These devices can write to their own program memory spaces under internal software control. By using a boot loader routine located in the protected Boot Block at the top of program memory, it becomes possible to create an application that can update itself in the field. Enhanced Peripheral Pin Select: The Peripheral Pin Select (PPS) module connects peripheral inputs and outputs to the device I/O pins. Only digital signals are included in the selections. All analog inputs and outputs remain fixed to their assigned pins. Windowed Watchdog Timer (WWDT): - Timer monitoring of overflow and underflow events - Variable prescaler selection - Variable window size selection - All sources configurable in hardware or software Details on Individual Family Members The devices of the PIC16(L)F184XX family described in the current datasheet are available in 14/20-pin packages. The block diagram for this device is shown in Figure 1-1. The devices have the following differences: 1. 2. 3. 4. 5. 6. 7. Program Flash Memory Data Memory SRAM Data Memory EEPROM A/D channels I/O ports Enhanced USART Input Voltage Range/Power Consumption All other features for devices in this family are identical. These are summarized in the following Device Features table. The pinouts for all devices are listed in the pin summary tables. Table 1-1. Device Features Features PIC16(L)F18424 PIC16(L)F18444 7 7 Program Memory (Instructions) 4096 4096 Data Memory (Bytes) 512 512 Data EEPROM Memory (Bytes) 256 256 Program Memory (KBytes) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 16 PIC16(L)F18424/44 Device Overview Features PIC16(L)F18424 PIC16(L)F18444 14 - PDIP 20 - PDIP 14 - SOIC (3.9 mm) 20 - SOIC (7.5 mm) 14 - TSSOP 20 - SSOP 16 - uQFN (4x4) 20 - uQFN (4x4) A, C A, B, C Capture/Compare/PWM Modules (CCP) 4 4 Configurable Logic Cell (CLC) 4 4 10-Bit Pulse-Width Modulator (PWM) 2 2 12-Bit Analog-to-Digital Module (ADC2) with Computation Accelerator 11 channels 17 channels 5-Bit Digital-to-Analog Module (DAC) 1 1 Comparators 2 2 Numerical Contolled Oscillator (NCO) 1 1 Interrupt Sources 38 38 Timers (16-/8-bit) 4 4 1 MSSP 1 MSSP 1 EUSART 1 EUSART Complementary Waveform Generator (CWG) 2 2 Zero-Cross Detect (ZCD) 1 1 Data Signal Modulator (DSM) 1 1 Reference Clock Output Module 1 1 Peripheral Pin Select (PPS) YES YES Peripheral Module Disable (PMD) YES YES Programmable Brown-out Reset (BOR) YES YES POR, BOR, RESET Instruction, Stack Overflow, Stack Underflow (PWRT, OST), MCLR, WDT POR, BOR, RESET Instruction, Stack Overflow, Stack Underflow (PWRT, OST), MCLR, WDT 50 instructions 50 instructions Packages I/O Ports Serial Communications Resets (and Delays) Instruction Set (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 17 PIC16(L)F18424/44 Device Overview Features PIC16(L)F18424 Filename: 10-000039AB.vsd Title: PIC16(L)F184xx Block Diagram Last Edit: 9/27/2017 16-levels hardware stack First Used: PIC16(L)F184xx Notes: 1. See applicable chapters for more information on peripherals. 2. See TableFrequency 1-1 for peripherals available on specific devices. Operating DC - 32 MHz 3. See Figure 2-1 4. PORTB available on PIC16(L)F18444/5/6 PIC16(L)F18444 16-levels hardware stack DC - 32 MHz Figure 1-1. PIC16(L)F18424/44 Device Block Diagram Program Flash Memory Rev. 10-000039AB 9/27/2017 RAM PORTA Timing Generation CLKOUT/OSC2 PORTB(2) EXTOSC Oscillator CLKIN/OSC1 PORTC CPU Secondary Oscillator (SOSC) SOSCI SOSCO MCLR NCO1 PWM7 CWG2 PWM6 CWG1 WDT Timer6 Timer5 Temp Indicator Timer4 EUSART1 Timer3 MSSP1 CLC4 Timer2 CLC3 Timer1 Timer0 CLC2 CLC1 C2 ADC2 12-bit C1 SMT1 CCP4 CCP3 DAC1 CCP2 FVR CCP1 Note: 1. See applicable chapters for more information on peripherals. 2. PORTB available only on 20-pin or higher pin-count devices. 1.4 Register and Bit naming conventions 1.4.1 Register Names When there are multiple instances of the same peripheral in a device, the peripheral control registers will be depicted as the concatenation of a peripheral identifier, peripheral instance, and control identifier. The control registers section will show just one instance of all the register names with an `x' in the place of the peripheral instance number. This naming convention may also be applied to peripherals when there is only one instance of that peripheral in the device to maintain compatibility with other devices in the family that contain more than one. 1.4.2 Bit Names There are two variants for bit names: * * Short name: Bit function abbreviation Long name: Peripheral abbreviation + short name (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 18 PIC16(L)F18424/44 Device Overview 1.4.2.1 Short Bit Names Short bit names are an abbreviation for the bit function. For example, some peripherals are enabled with the EN bit. The bit names shown in the registers are the short name variant. Short bit names are useful when accessing bits in C programs. The general format for accessing bits by the short name is RegisterNamebits.ShortName. For example, the enable bit, EN, in the CM1CON0 register can be set in C programs with the instruction CM1CON0bits.EN = 1. Short names are generally not useful in assembly programs because the same name may be used by different peripherals in different bit positions. When this occurs, during the include file generation, all instances of that short bit name are appended with an underscore plus the name of the register in which the bit resides to avoid naming contentions. 1.4.2.2 Long Bit Names Long bit names are constructed by adding a peripheral abbreviation prefix to the short name. The prefix is unique to the peripheral, thereby making every long bit name unique. The long bit name for the COG1 enable bit is the COG1 prefix, G1, appended with the enable bit short name, EN, resulting in the unique bit name G1EN. Long bit names are useful in both C and assembly programs. For example, in C the COG1CON0 enable bit can be set with the G1EN = 1 instruction. In assembly, this bit can be set with the BSF COG1CON0,G1EN instruction. 1.4.2.3 Bit Fields Bit fields are two or more adjacent bits in the same register. Bit fields adhere only to the short bit naming convention. For example, the three Least Significant bits of the COG1CON0 register contain the mode control bits. The short name for this field is MD. There is no long bit name variant. Bit field access is only possible in C programs. The following example demonstrates a C program instruction for setting the COG1 to the Push-Pull mode: COG1CON0bits.MD = 0x5; Individual bits in a bit field can also be accessed with long and short bit names. Each bit is the field name appended with the number of the bit position within the field. For example, the Most Significant mode bit has the short bit name MD2 and the long bit name is G1MD2. The following two examples demonstrate assembly program sequences for setting the COG1 to Push-Pull mode: Example 1: MOVLW ANDWF MOVLW IORWF ~(1< CALL, CALLW RETURN, RETLW Interrupt, RETFIE 15 Stack Level 0 Stack Level 1 Stack Level 15 Interrupt Vector 0004h 0005h 07FFh 0800h 0FFFh 1000h PIC16(L)F18425/45/55 17FFh 1800h PIC16(L)F18426/46/56 Page 0 0000h PIC16(L)F18424/44 On-chip Program Memory Reset Vector 1FFFh 2000h 3FFFh 4000h Unimplemented 7FFFh Related Links CONFIG5 Memory Violation 7.1.1 Reading Program Memory as Data There are three methods of accessing constants in program memory. The first method is to use tables of RETLW instructions. The second method is to set an FSR to point to the program memory. The third method is to use the NVMREG interface to access the program memory. Related Links NVMREG Access (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 46 PIC16(L)F18424/44 Memory Organization 7.1.1.1 RETLW Instruction The RETLW instruction can be used to provide access to tables of constants. The recommended way to create such a table is shown in the following example. constants BRW ;Add Index in W to ;program counter to ;select data ;Index0 data ;Index1 data RETLW DATA0 RETLW DATA1 RETLW DATA2 RETLW DATA3 my_function ;... LOTS OF CODE... MOVLW DATA_INDEX call constants ;... THE CONSTANT IS IN W The BRW instruction makes this type of table very simple to implement. 7.1.1.2 Indirect Read with FSR The program memory can be accessed as data by setting bit 7 of an FSRxH register and reading the matching INDFx register. The MOVIW instruction will place the lower eight bits of the addressed word in the W register. Writes to the program memory cannot be performed via the INDF registers. Instructions that read the program memory via the FSR require one extra instruction cycle to complete. The following example demonstrates reading the program memory via an FSR. The HIGH directive will set bit 7 if a label points to a location in the program memory. This applies to the assembly code shown below. constants RETLW DATA0 ;Index0 data RETLW DATA1 ;Index1 data RETLW DATA2 RETLW DATA3 my_function ;... LOTS OF CODE... MOVLW LOW constants MOVWF FSR1L MOVLW HIGH constants MOVWF FSR1H MOVIW 2[FSR1 ;DATA2 IS IN W 7.2 Memory Access Partition (MAP) User Flash is partitioned into: * Application Block * Boot Block, and * Storage Area Flash (SAF) Block The user can allocate the memory usage by setting the BBEN bit, selecting the size of the partition defined by BBSIZE bits and enabling the Storage Area Flash by the SAFEN bit of the Configuration Word. Refer to the following links for the different user Flash memory partitions. Related Links (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 47 PIC16(L)F18424/44 Memory Organization CONFIG4 7.2.1 Application Block Default settings of the Configuration bits (BBEN = 1 and SAFEN = 1) assign all memory in the user Flash area to the Application Block. 7.2.2 Boot Block If BBEN = 1, the Boot Block is enabled and a specific address range is allotted as the Boot Block based on the value of the BBSIZE bits and the sizes provided in Configuration Word 4. Related Links CONFIG4 7.2.3 Storage Area Flash Storage Area Flash (SAF) is enabled by clearing the SAFEN bit of the Configuration Word. If enabled, the SAF block is placed at the end of memory and spans 128 words. If the Storage Area Flash (SAF) is enabled, the SAF area is not available for program execution. Related Links CONFIG4 7.2.4 Memory Write Protection All the memory blocks have corresponding write protection fuses WRTAPP, WRTB and WRTC bits in the Configuration Word 4. If write-protected locations are written from NVMCON registers, memory is not changed and the WRERR bit defined in NVMCON1 register is set as explained in the "WRERR Bit" section. Related Links CONFIG4 NVMCON1 WRERR Bit 7.2.5 Memory Violation A Memory Execution Violation Reset occurs while executing an instruction that has been fetched from outside a valid execution area, clearing the MEMV bit. Refer to the "Memory Execution Violation" section for the available valid program execution areas and the PCON1 register definition for MEMV bit conditions. Table 7-2. Memory Access Partition Partition REG PFM Address 00 0000h ... Last Block (c) 2018 Microchip Technology Inc. BBEN = 1 SAFEN = 1 BBEN = 1 SAFEN = 0 BBEN = 0 SAFEN = 1 BBEN = 0 SAFEN = 0 APPLICATION BLOCK(4) APPLICATION BLOCK(4) BOOT BLOCK(4) BOOT BLOCK(4) Datasheet Preliminary DS40002000A-page 48 PIC16(L)F18424/44 Memory Organization Partition REG Address BBEN = 1 SAFEN = 1 BBEN = 1 SAFEN = 0 BBEN = 0 SAFEN = 1 BBEN = 0 SAFEN = 0 Memory Address Last Boot Block Memory Address + 1(1) ... Last Program Memory Address - 80h Last Program Memory Address 7Fh(2) ... Last Program Memory Address CONFIG Config Memory Address(3) APPLICATION BLOCK(4) APPLICATION BLOCK(4) SAF(4) SAF(4) CONFIG Note: 1. Last Boot Block Memory Address is based on BBSIZE given in "Configuration Word 4". 2. Last Program Memory Address is the Flash size given in the "Program Memory Organization". 3. Config Memory Address are the address locations of the Configuration Words given in the "NVMREG Access to Device Information Area, Device Configuration Area, User ID, Device ID, EEPROM, and Configuration Words" section. 4. Each memory block has a corresponding write protection fuse defined by the WRTAPP, WRTB and WRTC bits in the "Configuration Word 4". Related Links Memory Execution Violation PCON1 CONFIG4 Program Memory Organization NVMREG Access to Device Information Area, Device Configuration Area, User ID, Device ID, EEPROM, and Configuration Words 7.3 Data Memory Organization The data memory is partitioned into 64 memory banks with 128 bytes in each bank. Each bank consists of: * 12 core registers * Up to 100 Special Function Registers (SFR) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 49 PIC16(L)F18424/44 Memory Organization * * Up to 80 bytes of General Purpose RAM (GPR) 16 bytes of common RAM Figure 7-2. Banked Memory Partition Rev. 10-000 041C 11/8/201 7 7-bit Bank Offset Typical Memory Bank 00h Core Registers (12 bytes) 0Bh 0Ch Special Function Registers (up to 20 bytes maximum) 1Fh 20h Special Function Registers or General Purpose RAM (80 bytes maximum) 6Fh 70h Common RAM (16 bytes) 7Fh 7.3.1 Bank Selection The active bank is selected by writing the bank number into the Bank Select Register (BSR). All data memory can be accessed either directly (via instructions that use the file registers) or indirectly via the two File Select Registers (FSR). Data memory uses a 13-bit address. The upper six bits of the address define the Bank address and the lower seven bits select the registers/RAM in that bank. Related Links Indirect Addressing BSR 7.3.2 Core Registers The core registers contain the registers that directly affect the basic operation. The core registers occupy the first 12 addresses of every data memory bank (addresses n00h/n80h through n0Bh/n8Bh). These registers are listed below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 50 PIC16(L)F18424/44 Memory Organization Table 7-3. Core Registers 7.3.2.1 Addresses in BANKx Core Registers n00h or n80h INDF0 n01h or n81h INDF1 n02h or n82h PCL n03 or n83h STATUS n04h or n84h FSR0L n05h or n85h FSR0H n06h or n86h FSR1L n07h or n87h FSR1H n08h or n88h BSR n09h or n89h WREG n0Ah or n8Ah PCLATH n0Bh or n8Bh INTCON STATUS Register The STATUS register contains: * the arithmetic status of the ALU * the Reset status The STATUS register can be the destination for any instruction, like any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. For example, CLRF STATUS will clear bits <4:3> and <1:0>, and set the Z bit. This leaves the STATUS register as `000u u1uu' (where u = unchanged). It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register, because these instructions do not affect any Status bits. For other instructions not affecting any Status bits, refer to the "Instruction Set Summary" section. Important: The C and DC bits operate as Borrow and Digit Borrow out bits, respectively, in subtraction. Related Links STATUS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 51 PIC16(L)F18424/44 Memory Organization 7.3.3 Special Function Register The Special Function Registers are registers used by the application to control the desired operation of peripheral functions in the device. The Special Function Registers occupy the first 20 bytes of the data banks 0-59 and the first 100 bytes of the data banks 60-63, after the core registers. The SFRs associated with the operation of the peripherals are described in the appropriate peripheral chapter of this data sheet. 7.3.4 General Purpose RAM There are up to 80 bytes of GPR in each data memory bank. 7.3.4.1 Linear Access to GPR The general purpose RAM can be accessed in a non-banked method via the FSRs. This can simplify access to large memory structures. Related Links Linear Data Memory 7.3.5 Common RAM There are 16 bytes of common RAM accessible from all banks. 7.4 PCL and PCLATH The Program Counter (PC) is 15 bits wide. The low byte comes from the PCL register, which is a readable and writable register. The high byte (PC<14:8>) is not directly readable or writable and comes from PCLATH. On any Reset, the PC is cleared. The following figure shows the five situations for the loading of the PC. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 52 Filename: Title: Last Edit: First Used: Note: 10-000042A.vsd LOADING OF PC IN DIFFERENT SITUATIONS 7/30/2013 PIC16F1508/9 PIC16(L)F18424/44 Memory Organization Figure 7-3. Loading of PC in Different Situations Rev. 10-000042A 7/30/2013 PC PCLATH PC PCLATH PC PCLATH PC 14 7 6 14 6 PCH 6 14 0 0 GOTO, CALL 11 OPCODE <10:0> PCH 7 Instruction with PCL as Destination 8 PCL 0 0 ALU result PCH 4 14 PCL PCL 0 PCH 0 CALLW 8 W PCL 0 PCL 0 BRW 15 PC + W PC 14 PCH BRA 15 PC + OPCODE <8:0> 7.4.1 Modifying PCL Executing any instruction with the PCL register as the destination simultaneously causes the Program Counter PC<14:8> bits (PCH) to be replaced by the contents of the PCLATH register. This allows the entire contents of the Program Counter to be changed by writing the desired upper seven bits to the PCLATH register. When the lower eight bits are written to the PCL register, all 15 bits of the Program Counter will change to the values contained in the PCLATH register and those being written to the PCL register. 7.4.2 Computed GOTO A computed GOTO is accomplished by adding an offset to the Program Counter (ADDWF PCL). When performing a table read using a computed GOTO method, care should be exercised if the table location crosses a PCL memory boundary (each 256-byte block). Refer to Application Note AN556, "Implementing a Table Read" (DS00556). 7.4.3 Computed Function Calls A computed function CALL allows programs to maintain tables of functions and provide another way to execute state machines or look-up tables. When performing a table read using a computed function CALL, care should be exercised if the table location crosses a PCL memory boundary (each 256-byte block). If using the CALL instruction, the PCH<2:0> and PCL registers are loaded with the operand of the CALL instruction. PCH<6:3> is loaded with PCLATH<6:3>. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 53 PIC16(L)F18424/44 Memory Organization The CALLW instruction enables computed calls by combining PCLATH and W to form the destination address. A computed CALLW is accomplished by loading the W register with the desired address and executing CALLW. The PCL register is loaded with the value of W and PCH is loaded with PCLATH. 7.4.4 Branching The branching instructions add an offset to the PC. This allows relocatable code and code that crosses page boundaries. There are two forms of branching, BRW and BRA. The PC will have incremented to fetch the next instruction in both cases. When using either branching instruction, a PCL memory boundary may be crossed. If using BRW, load the W register with the desired unsigned address and execute BRW. The entire PC will be loaded with the address PC + 1 + W. If using BRA, the entire PC will be loaded with PC + 1 + the signed value of the operand of the BRA instruction. 7.5 Stack All devices have a 16-level by 15-bit wide hardware stack. The stack space is not part of either program or data space. The PC is PUSHed onto the stack when CALL or CALLW instructions are executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not affected by a PUSH or POP operation. The stack operates as a circular buffer if the STVREN Configuration bit is programmed to `0`. This means that after the stack has been PUSHed sixteen times, the seventeenth PUSH overwrites the value that was stored from the first PUSH. The eighteenth PUSH overwrites the second PUSH (and so on). The STKOVF and STKUNF flag bits will be set on an Overflow/Underflow, regardless of whether the Reset is enabled. Important: There are no instructions/mnemonics called PUSH or POP. These are actions that occur from the execution of the CALL, CALLW, RETURN, RETLW and RETFIE instructions or the vectoring to an interrupt address. 7.5.1 Accessing the Stack The stack is accessible through the TOSH, TOSL and STKPTR registers. STKPTR is the current value of the Stack Pointer. TOSH:TOSL register pair points to the TOP of the stack. Both registers are read/ writable. TOS is split into TOSH and TOSL due to the 15-bit size of the PC. To access the stack, adjust the value of STKPTR, which will position TOSH:TOSL, then read/write to TOSH:TOSL. STKPTR is five bits to allow detection of overflow and underflow. Important: Care should be taken when modifying the STKPTR while interrupts are enabled. During normal program operation, CALL, CALLW and interrupts will increment STKPTR while RETLW, RETURN, and RETFIE will decrement STKPTR. STKPTR can be monitored to obtain to value of stack (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 54 PIC16(L)F18424/44 Memory Organization memory left at any 10-000043A.vsd given time. The STKPTR always points at the currently used place on the stack. Filename: Title: ACCESSING THE STACK EXAMPLE 1 Therefore, a CALL or CALLW will increment the STKPTR and then write the PC, and a return will unload Last Edit: 7/30/2013 the PC stack and then decrement the STKPTR. First value Used: from the PIC16F1508/9 Note: Reference the following figures for examples of accessing the stack. Figure 7-4. Accessing the Stack Example 1 Rev. 10-000043A 7/30/2013 TOSH:TOSL 0x0F STKPTR = 0x1F 0x0E Stack Reset Disabled (STVREN = 0) 0x0D 0x0C 0x0B Initial Stack Configuration: 0x0A After Reset, the stack is empty. The empty stack is initialized so the Stack Pointer is pointing at 0x1F. If the Stack Overflow/Underflow Reset is enabled, the TOSH/TOSL register will return `0'. If the Stack Overflow/Underflow Reset is disabled, the TOSH/TOSL register will return the contents of stack address 0x0F. 0x09 0x08 0x07 0x06 0x05 0x04 0x03 0x02 0x01 0x00 TOSH:TOSL (c) 2018 Microchip Technology Inc. 0x1F 0x0000 STKPTR = 0x1F Datasheet Preliminary Stack Reset Enabled (STVREN = 1) DS40002000A-page 55 Filename: Title: Last Edit: First Used: Note: 10-000043B.vsd ACCESSING THE STACKS EXAMPLE 2 7/30/2013 PIC16F1508/9 PIC16(L)F18424/44 Memory Organization Figure 7-5. Accessing the Stack Example 2 Rev. 10-000043B 7/30/2013 0x0F 0x0E 0x0D 0x0C 0x0B 0x0A This figure shows the stack configuration after the first CALL or a single interrupt. If a RETURN instruction is executed, the return address will be placed in the Program Counter and the Stack Pointer decremented to the empty state (0x1F). 0x09 0x08 0x07 0x06 0x05 0x04 0x03 Filename: Title: Last Edit: First Used: Note: 10-000043C.vsd 0x02 ACCESSING THE STACK EXAMPLE 3 0x01 7/30/2013 PIC16F1508/9 TOSH:TOSL 0x00 Return Address STKPTR = 0x00 Figure 7-6. Accessing the Stack Example 3 Rev. 10-000043C 7/30/2013 0x0F 0x0E 0x0D 0x0C After seven CALLs or six CALLs and an interrupt, the stack looks like the figure on the left. A series of RETURN instructions will repeatedly place the return addresses into the Program Counter and pop the stack. 0x0B 0x0A 0x09 0x08 0x07 TOSH:TOSL (c) 2018 Microchip Technology Inc. 0x06 Return Address 0x05 Return Address 0x04 Return Address 0x03 Return Address 0x02 Return Address 0x01 Return Address 0x00 Return Address STKPTR = 0x06 Datasheet Preliminary DS40002000A-page 56 Filename: Title: Last Edit: First Used: Note: 10-000043D.vsd ACCESSING THE STACK EXAMPLE 4 7/30/2013 PIC16F1508/9 PIC16(L)F18424/44 Memory Organization Figure 7-7. Accessing the Stack Example 4 Rev. 10-000043D 7/30/2013 TOSH:TOSL 0x0F Return Address 0x0E Return Address 0x0D Return Address 0x0C Return Address 0x0B Return Address 0x0A Return Address 0x09 Return Address 0x08 Return Address 0x07 Return Address 0x06 Return Address 0x05 Return Address 0x04 Return Address 0x03 Return Address 0x02 Return Address 0x01 Return Address 0x00 Return Address When the stack is full, the next CALL or an interrupt will set the Stack Pointer to 0x10. This is identical to address 0x00 so the stack will wrap and overwrite the return address at 0x00. If the Stack Overflow/Underflow Reset is enabled, a Reset will occur and location 0x00 will not be overwritten. STKPTR = 0x10 Related Links TOS 7.5.2 Overflow/Underflow Reset If the STVREN bit in Configuration Word 2 is programmed to `1', the device will be Reset if the stack is PUSHed beyond the sixteenth level or POPed beyond the first level, setting the appropriate bits (STKOVF or STKUNF, respectively) in the PCON register. Related Links CONFIG2 7.6 Indirect Addressing The INDFn registers are not physical registers. Any instruction that accesses an INDFn register actually accesses the register at the address specified by the File Select Registers (FSR). If the FSRn address specifies one of the two INDFn registers, the read will return `0' and the write will not occur (though Status bits may be affected). The FSRn register value is created by the pair FSRnH and FSRnL. The FSR registers form a 16-bit address that allows an addressing space with 65536 locations. These locations are divided into three memory regions: * Traditional/Banked Data Memory * Linear Data Memory * Program Flash Memory (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 57 Filename: Title: Last Edit: First Used: Note: 10-000044F.vsd INDIRECT ADDRESSING 1/13/2017 PIC16(L)F153XX PIC16(L)F18424/44 Memory Organization Figure 7-8. Indirect Addressing PIC16(L)F18424/44 Rev. 10-000044F 1/13/2017 0x0000 0x0000 Traditional Data Memory 0x1FFF 0x2000 Linear Data Memory 0X2FEF 0X2FF0 FSR Address Range 0x7FFF 0x8000 Reserved PC value = 0x000 Program Flash Memory 0x87FF PC value = 0x7FF Related Links FSR0 7.6.1 Traditional/Banked Data Memory The traditional or banked data memory is a region from FSR address 0x000 to FSR address 0x1FFF. The addresses correspond to the absolute addresses of all SFR, GPR and common registers. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 58 Filename: Title: Last Edit: First Used: Note: PIC16(L)F18424/44 10-000056B.vsd TRADITIONAL DATA MEMORY MAP 12/14/2016 PIC16F153xx Memory Organization Figure 7-9. Traditional/Banked Data Memory Map Rev. 10-000056B 12/14/2016 Direct Addressing 5 BSR 0 Indirect Addressing From Opcode 6 0 Bank Select 7 FSRxH 0 0 0 Location Select 0x00 Bank Select 000000 000001 000010 111111 Bank 0 Bank 1 Bank 63 0 7 FSRxL 0 Location Select 0x7F 7.6.2 Bank 2 Linear Data Memory The linear data memory is the region from FSR address 0x2000 to FSR address 0X2FEF. This region is a virtual region that points back to the 80-byte blocks of GPR memory in all the banks. Refer to the following figure for the Linear Data Memory Map. Important: The address range 0x2000 to 0x2FF0 represents the complete addressable Linear Data Memory up to Bank 50. The actual implemented Linear Data Memory will differ from one device to the other in a family. Confirm the memory limits on every device. Unimplemented memory reads as 0x00. Use of the linear data memory region allows buffers to be larger than 80 bytes because incrementing the FSR beyond one bank will go directly to the GPR memory of the next bank. The 16 bytes of common memory are not included in the linear data memory region. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 59 Filename: Title: Last Edit: First Used: Note: 10-000057B.vsd LINEAR DATA MEMORY MAP 8/24/2016 PIC16F153xx PIC16(L)F18424/44 Memory Organization Figure 7-10. Linear Data Memory Map Rev. 10-000057B 8/24/2016 7 FSRnH 0 7 Location Select FSRnL 0 0x2000 0x020 Bank 0 0x06F 0x0A0 Bank 1 0x0EF 0x120 Bank 2 0x16F 0x2FEF 7.6.3 0x1920 Bank 50 0x196F Program Flash Memory To make constant data access easier, the entire Program Flash Memory is mapped to the upper half of Filename: 10-000058A.vsd the FSR address space. When Title: the MSB of FSRnH is set, the lower 15 bits are the address in program PROGRAM FLASH MEMORY MAP memory which will be accessedLast through INDF. Only the lower eight bits of each memory location are Edit: 7/31/2013 First Used: PIC16F1508/9 accessible via INDF. Writing to the Program Flash Memory cannot be accomplished via the FSR/INDF Note: interface. All instructions that access Program Flash Memory via the FSR/INDF interface will require one additional instruction cycle to complete. Figure 7-11. Program Flash Memory Map Rev. 10-000058A 7/31/2013 7 1 FSRnH 0 7 Location Select FSRnL 0 0x8000 0x0000 Program Flash Memory (low 8 bits) 0xFFFF 7.7 0x7FFF Register Summary - Memory and Status Offset Name Bit Pos. 0x00 INDF0 7:0 INDF[7:0] 0x01 INDF1 7:0 INDF[7:0] (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 60 PIC16(L)F18424/44 Memory Organization Offset Name Bit Pos. 0x02 PCL 7:0 0x03 STATUS 7:0 0x04 0x05 0x06 0x07 FSR0 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x08 BSR 7:0 0x09 WREG 7:0 0x0A PCLATH 7:0 0x0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0C ... Reserved 0x0FEC 0x0FED 0x0FEE 0x0FEF 7.8 STKPTR TOS 7:0 STKPTR[4:0] 7:0 TOSL[7:0] 15:8 TOSH[7:0] Register Definitions: Memory and Status (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 61 PIC16(L)F18424/44 Memory Organization 7.8.1 INDF0 Name: Offset: INDF0 0x00 + n*0x80 [n=0..63] Indirect Data Register. This is a virtual register. The GPR/SFR register addressed by the FSR0 register is the target for all operations involving the INDF0 register. Bit 7 6 5 4 3 2 1 0 INDF0[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - INDF0[7:0] Indirect data pointed to by the FSR0 register Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 62 PIC16(L)F18424/44 Memory Organization 7.8.2 INDF1 Name: Offset: INDF1 0x01 + n*0x80 [n=0..63] Indirect Data Register. This is a virtual register. The GPR/SFR register addressed by the FSR1 register is the target for all operations involving the INDF1 register. Bit 7 6 5 4 3 2 1 0 INDF1[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - INDF1[7:0] Indirect data pointed to by the FSR1 register Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 63 PIC16(L)F18424/44 Memory Organization 7.8.3 PCL Name: Offset: PCL 0x02 + n*0x80 [n=0..63] Low byte of the Program Counter Bit 7 6 5 4 3 2 1 0 PCL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - PCL[7:0] Provides direct read and write access to the Program Counter (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 64 PIC16(L)F18424/44 Memory Organization 7.8.4 STATUS Name: Offset: STATUS 0x03 + n*0x80 [n=0..63] Status Register Bit 7 6 5 Access Reset 4 3 2 1 0 TO PD Z DC C RO RO R/W R/W R/W 1 1 0 0 0 Bit 4 - TO Time-Out bit Reset States: POR/BOR = 1 All Other Resets = q Value 1 0 Description Set at power-up or by execution of CLRWDT or SLEEP instruction A WDT time-out occurred Bit 3 - PD Power-Down bit Reset States: POR/BOR = 1 All Other Resets = q Value 1 0 Description Set at power-up or by execution of CLRWDT instruction Cleared by execution of the SLEEP instruction Bit 2 - Z Zero bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description The result of an arithmetic or logic operation is zero The result of an arithmetic or logic operation is not zero Bit 1 - DC Digit Carry/Borrow bit(1) ADDWF, ADDLW, SUBLW, SUBWF instructions Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description A carry-out from the 4th low-order bit of the result occurred No carry-out from the 4th low-order bit of the result Bit 0 - C Carry/Borrow bit(1) ADDWF, ADDLW, SUBLW, SUBWF instructions Reset States: POR/BOR = 0 All Other Resets = u (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 65 PIC16(L)F18424/44 Memory Organization Value 1 0 Description A carry-out from the Most Significant bit of the result occurred No carry-out from the Most Significant bit of the result occurred Note: 1. For Borrow, the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For Rotate (RRCF, RLCF) instructions, this bit is loaded with either the high or low-order bit of the Source register. Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 66 PIC16(L)F18424/44 Memory Organization 7.8.5 FSR0 Name: Offset: FSR0 0x04 + n*0x80 [n=0..63] Indirect Address Register. The FSR value is the address of the data to which the INDF register points. Bit 15 14 13 12 11 10 9 8 FSRH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 FSRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 15:8 - FSRH[7:0] Most Significant address of INDF data Bits 7:0 - FSRL[7:0] Least Significant address of INDF data Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 67 PIC16(L)F18424/44 Memory Organization 7.8.6 FSR1 Name: Offset: FSR1 0x06 + n*0x80 [n=0..63] Indirect Address Register. The FSR value is the address of the data to which the INDF register points. Bit 15 14 13 12 11 10 9 8 FSRH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 FSRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 15:8 - FSRH[7:0] Most Significant address of INDF data Bits 7:0 - FSRL[7:0] Least Significant address of INDF data (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 68 PIC16(L)F18424/44 Memory Organization 7.8.7 BSR Name: Offset: BSR 0x08 + n*0x80 [n=0..63] Bank Select Register The BSR indicates the data memory bank by writing the bank number into the register. All data memory can be accessed directly via instructions, or indirectly via FSRs. Bit 7 6 5 4 3 2 1 0 BSR[5:0] Access Reset R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 5:0 - BSR[5:0] Six Most Significant bits of the data memory address Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 69 PIC16(L)F18424/44 Memory Organization 7.8.8 WREG Name: Offset: WREG 0x09 + n*0x80 [n=0..63] Working Data Register Bit 7 6 5 4 3 2 1 0 WREG[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - WREG[7:0] Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 70 PIC16(L)F18424/44 Memory Organization 7.8.9 PCLATH Name: Offset: PCLATH 0x0A + n*0x80 [n=0..63] Program Counter Latches. Write Buffer for the upper 7 bits of the Program Counter Bit 7 6 5 4 R/W R/W R/W 0 0 0 3 2 1 0 R/W R/W R/W R/W 0 0 0 0 PCLATH[6:0] Access Reset Bits 6:0 - PCLATH[6:0] High PC Latch register Holding register for Program Counter bits <6:0> Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 71 PIC16(L)F18424/44 Memory Organization 7.8.10 INTCON Name: Offset: INTCON 0x0B + n*0x80 [n=0..63] Interrupt Control Register Bit Access Reset 7 6 GIE PEIE 5 4 3 2 1 INTEDG 0 R/W R/W R/W 0 0 1 Bit 7 - GIE Global Interrupt Enable bit Value 1 0 Description Enables all active interrupts Disables all interrupts Bit 6 - PEIE Peripheral Interrupt Enable bit Value 1 0 Description Enables all active peripheral interrupts Disables all peripheral interrupts Bit 0 - INTEDG External Interrupt Edge Select bit Value 1 0 Description Interrupt on rising edge of INT pin Interrupt on falling edge of INT pin Important: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 72 PIC16(L)F18424/44 Memory Organization 7.8.11 TOS Name: Offset: TOS 0x1FEE Top-of-Stack Registers Contents of the stack pointed to by the STKPTR register. To access the stack, adjust the value of STKPTR, which will position TOSH:TOSL, then read/write to TOSH:TOSL. Bit 15 14 13 12 11 10 9 8 TOSH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 TOSL[7:0] Access Reset Bits 15:8 - TOSH[7:0] High Byte of the TOS Register Bits <15:8> of the TOS Bits 7:0 - TOSL[7:0] Low Byte TOS Register Bits <7:0> of the TOS Related Links Core Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 73 PIC16(L)F18424/44 Memory Organization 7.8.12 STKPTR Name: Offset: STKPTR 0x1FED Stack Pointer Register Bit 7 6 5 4 3 2 1 0 STKPTR[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - STKPTR[4:0] Stack Pointer Location bits (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 74 PIC16(L)F18424/44 Memory Organization 7.9 Register Summary: Shadow Registers Offset Name Bit Pos. 0x1FE4 STATUS_SHAD 7:0 0x1FE5 WREG_SHAD 7:0 0x1FE6 BSR_SHAD 7:0 0x1FE7 PCLATH_SHAD 7:0 0x1FE8 FSR0_SHAD 0x1FEA FSR1_SHAD 7.10 TO PD Z DC C WREG[7:0] BSR[5:0] PCLATH[6:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Register Definitions: Shadow Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 75 PIC16(L)F18424/44 Memory Organization 7.10.1 STATUS_SHAD Name: Offset: STATUS_SHAD 0x1FE4 Shadow of Status Register Bit 7 6 5 Access Reset 4 3 2 1 0 TO PD Z DC C RO RO R/W R/W R/W x x x x x Bit 4 - TO Time-Out bit Reset States: POR/BOR = x All Other Resets = u Value 1 0 Description Set at power-up or by execution of CLRWDT or SLEEP instruction A WDT time-out occurred Bit 3 - PD Power-Down bit Reset States: POR/BOR = x All Other Resets = u Value 1 0 Description Set at power-up or by execution of CLRWDT instruction Cleared by execution of the SLEEP instruction Bit 2 - Z Zero bit Reset States: POR/BOR = x All Other Resets = u Value 1 0 Description The result of an arithmetic or logic operation is zero The result of an arithmetic or logic operation is not zero Bit 1 - DC Digit Carry/Borrow bit(1) ADDWF, ADDLW, SUBLW, SUBWF instructions Reset States: POR/BOR = x All Other Resets = u Value 1 0 Description A carry-out from the 4th low-order bit of the result occurred No carry-out from the 4th low-order bit of the result Bit 0 - C Carry/Borrow bit(1) ADDWF, ADDLW, SUBLW, SUBWF instructions Reset States: POR/BOR = x All Other Resets = u (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 76 PIC16(L)F18424/44 Memory Organization Value 1 0 Description A carry-out from the Most Significant bit of the result occurred No carry-out from the Most Significant bit of the result occurred Note: 1. For Borrow, the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For Rotate (RRCF, RLCF) instructions, this bit is loaded with either the high or low-order bit of the Source register. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 77 PIC16(L)F18424/44 Memory Organization 7.10.2 WREG_SHAD Name: Offset: WREG_SHAD 0x1FE5 Shadow of Working Data Register Bit 7 6 5 4 3 2 1 0 WREG[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 7:0 - WREG[7:0] Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 78 PIC16(L)F18424/44 Memory Organization 7.10.3 BSR_SHAD Name: Offset: BSR_SHAD 0x1FE6 Shadow of Bank Select Register The BSR indicates the data memory bank by writing the bank number into the register. All data memory can be accessed directly via instructions, or indirectly via FSRs. Bit 7 6 5 4 3 2 1 0 BSR[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - BSR[5:0] Six Most Significant bits of the data memory address Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 79 PIC16(L)F18424/44 Memory Organization 7.10.4 PCLATH_SHAD Name: Offset: PCLATH_SHAD 0x1FE7 Shadow of Program Counter Latches. Write Buffer for the upper 7 bits of the Program Counter Bit 7 6 5 4 R/W R/W R/W x x x 3 2 1 0 R/W R/W R/W R/W x x x x PCLATH[6:0] Access Reset Bits 6:0 - PCLATH[6:0] High PC Latch register Holding register for Program Counter bits <6:0> Reset States: POR/BOR = xxxxxxx All Other Resets = uuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 80 PIC16(L)F18424/44 Memory Organization 7.10.5 FSR_SHAD Name: Offset: FSRx_SHAD 0x1FE8,0x1FEA Shadow of Indirect Address Register. The FSR value is the address of the data to which the INDF register points. Bit 15 14 13 12 11 10 9 8 FSRH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset x x x x x x x x Bit 7 6 5 4 3 2 1 0 FSRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 15:8 - FSRH[7:0] Most Significant address of INDF data Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Bits 7:0 - FSRL[7:0] Least Significant address of INDF data Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 81 PIC16(L)F18424/44 Resets 8. Resets There are multiple ways to reset this device: * * * * * * Power-on Reset (POR) Brown-out Reset (BOR) Low-Power Brown-out Reset (LPBOR) MCLR Reset WDT Reset RESET instruction * * * Stack Overflow Stack Underflow Programming mode exit To allow VDD to stabilize, an optional Power-up Timer can be enabled to extend the Reset time after a BOR or POR event. A simplified block diagram of the On-Chip Reset Circuit is shown in the block diagram below. Figure 8-1. Simplified Block Diagram of On-Chip Reset Circuit Rev. 10-000006G 4/6/2017 ICSPTM Programming Mode Exit RESET Instruction Memory Violation Stack Underflow Stack Overflow VPP /MCLR MCLRE WWDT Time-out/ Window violation Device Reset Power-on Reset VDD Brown-out Reset Power-up Timer LFINTOSC LPBOR Reset 2 PWRTS<1:0> Note: See "BOR Operating Conditions" table for BOR active conditions. Related Links BOR Controlled by Software (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 82 PIC16(L)F18424/44 Resets 8.1 Power-on Reset (POR) The POR circuit holds the device in Reset until VDD has reached an acceptable level for minimum operation. Slow rising VDD, fast operating speeds or analog performance may require greater than minimum VDD. The PWRT, BOR or MCLR features can be used to extend the start-up period until all device operation conditions have been met. Related Links BOR Controlled by Software 8.2 Brown-out Reset (BOR) The BOR circuit holds the device in Reset when VDD reaches a selectable minimum level. Between the POR and BOR, complete voltage range coverage for execution protection can be implemented. The Brown-out Reset module has four operating modes controlled by the BOREN<1:0> bits in Configuration Words. The four operating modes are: * * * * BOR is always on BOR is off when in Sleep BOR is controlled by software BOR is always off Refer to "BOR Operating Conditions" table for more information. The Brown-out Reset voltage level is selectable by configuring the BORV<1:0> bits in Configuration Words. A VDD noise rejection filter prevents the BOR from triggering on small events. If VDD falls below VBOR for a duration greater than parameter TBORDC, the device will reset. 8.2.1 BOR is Always On When the BOREN bits of Configuration Words are programmed to `11', the BOR is always on. The device start-up will be delayed until the BOR is ready and VDD is higher than the BOR threshold. BOR protection is active during Sleep. The BOR does not delay wake-up from Sleep. 8.2.2 BOR is OFF in Sleep When the BOREN bits of Configuration Words are programmed to `10', the BOR is on, except in Sleep. The device start-up will be delayed until the BOR is ready and VDD is higher than the BOR threshold. BOR protection is not active during Sleep. The device wake-up will be delayed until the BOR is ready. 8.2.3 BOR Controlled by Software When the BOREN bits of Configuration Words are programmed to `01', the BOR is controlled by the SBOREN bit. The device start-up is not delayed by the BOR ready condition or the VDD level. BOR protection begins as soon as the BOR circuit is ready. The status of the BOR circuit is reflected in the BORRDY bit. BOR protection is unchanged by Sleep. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 83 PIC16(L)F18424/44 Resets Table 8-1. BOR Operating Conditions Device Mode BOR Mode X Active Waits for release of BOR(1) (BORRDY = 1) Awake Active Sleep Disabled Waits for release of BOR (BORRDY = 1) Waits for BOR Reset release 1 X Active 0 X Disabled X X Disabled BOREN<1:0> SBOREN 11 X 10 X 01 00 Instruction Execution upon: Release of POR or Wake-up from Sleep Waits for BOR Reset release (BORRDY = 1) Begins immediately (BORRDY = x) Note: 1. In this specific case, "Release of POR" and "Wake-up from Sleep", there is no delay in start-up. The BOR ready flag, (BORRDY = 1), will be set before the CPU is ready to execute instructions because the BOR circuit is forced on by the BOREN<1:0> bits Figure 8-2. Brown-out Situations Rev. 30-000092A 4/12/2017 VDD VBOR Internal Reset TPWRT(1) VDD VBOR Internal Reset < TPWRT TPWRT(1) VDD VBOR Internal Reset TPWRT(1) Note: TPWRT delay only if PWRTS bit field is programmed to a value different from `11'. 8.2.4 BOR is Always Off When the BOREN bits of the Configuration Words are programmed to `00', the BOR is off at all times. The device start-up is not delayed by the BOR ready condition or the VDD level. 8.3 Low-Power Brown-out Reset (LPBOR) The Low-Power Brown-out Reset (LPBOR) provides an additional BOR circuit for low-power operation. Refer to the figure below to see how the BOR interacts with other modules. The LPBOR is used to monitor the external VDD pin. When too low of a voltage is detected, the device is held in Reset. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 84 PIC16(L)F18424/44 Resets Figure 8-3. LPBOR, BOR, POR Relationship Rev. 30-000091B 6/21/2017 Any Reset BOR BOR Event REARM POR Event To PCON indicator bit POR LPBOR POR Event LPBOR Event Reset logic 8.3.1 Enabling LPBOR The LPBOR is controlled by the LPBOREN bit of Configuration Word 2. When the device is erased, the LPBOR module defaults to disabled. Related Links CONFIG2 8.3.2 8.4 LPBOR Module Output The output of the LPBOR module is a signal indicating whether or not a Reset is to be asserted. This signal is OR'd together with the Reset signal of the BOR module to provide the generic BOR signal, which goes to the PCON0 register and to the power control block. MCLR The MCLR is an optional external input that can reset the device. The MCLR function is controlled by the MCLRE bit of Configuration Words and the LVP bit of Configuration Words (see table below). The RMCLR bit in the PCON0 register will be set to `0' if a MCLR has occurred. Table 8-2. MCLR Configuration 8.4.1 MCLRE LVP MCLR x 1 Enabled 1 0 Enabled 0 0 Disabled MCLR Enabled When MCLR is enabled and the pin is held low, the device is held in Reset. The MCLR pin is connected to VDD through an internal weak pull-up. The device has a noise filter in the MCLR Reset path. The filter will detect and ignore small pulses. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 85 PIC16(L)F18424/44 Resets Important: An internal Reset event (RESET instruction, BOR, WWDT, POR, STKOVF, STKUNF) does not drive the MCLR pin low. Related Links Master Clear (MCLR) Pin 8.4.2 MCLR Disabled When MCLR is disabled, the MCLR becomes input-only and pin functions such as internal weak pull-ups are under software control. Related Links I/O Priorities 8.5 Windowed Watchdog Timer (WWDT) Reset The Windowed Watchdog Timer generates a Reset if the firmware does not issue a CLRWDT instruction within the time-out period or window set. The TO and PD bits in the STATUS register and the RWDT bit are changed to indicate a WDT Reset. The WDTWV bit indicates if the WDT Reset has occurred due to a timeout or a window violation. Related Links STATUS (WWDT) Windowed Watchdog Timer 8.6 RESET Instruction A RESET instruction will cause a device Reset. The RI bit will be set to `0'. See "Reset Condition for Special Registers" table for default conditions after a RESET instruction has occurred. 8.7 Stack Overflow/Underflow Reset The device can reset when the Stack Overflows or Underflows. The STKOVF or STKUNF bits register indicate the Reset condition. These Resets are enabled by setting the STVREN bit in Configuration Words. Related Links CONFIG2 Overflow/Underflow Reset 8.8 Programming Mode Exit Upon exit of Programming mode, the device will behave as if a POR had just occurred. 8.9 Power-up Timer (PWRT) The Power-up Timer optionally delays device execution after a BOR or POR event. This timer is typically used to allow VDD to stabilize before allowing the device to start running. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 86 PIC16(L)F18424/44 Resets The Power-up Timer is controlled by the PWRTS bit field of the Configuration Words. The Power-up Timer provides a nominal 64 ms timeout on POR or Brown-out Reset. The device is held in Reset as long as PWRT is active. The PWRT delay allows additional time for the VDD to rise to an acceptable level. The Power-up Timer is enabled by setting a non-zero value in the PWRTS bit field, in Configuration Words. The Power-up Timer starts after the release of the POR and BOR. For additional information, refer to Application Note AN607, "Power-up Trouble Shooting" (DS00000607). 8.10 Start-up Sequence Upon the release of a POR or BOR, the following must occur before the device will begin executing: 1. 2. 3. Power-up Timer runs to completion (if enabled). Oscillator start-up timer runs to completion (if required for selected oscillator source). MCLR must be released (if enabled). The total timeout will vary based on oscillator configuration and Power-up Timer configuration. The Power-up Timer and oscillator start-up timer run independently of MCLR Reset. If MCLR is kept low long enough, the Power-up Timer and oscillator Start-up Timer will expire. Upon bringing MCLR high, the device will begin execution after ten FOSC cycles (see figure below). This is useful for testing purposes or to synchronize more than one device operating in parallel. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 87 PIC16(L)F18424/44 Resets Figure 8-4. Reset Start-up Sequence Rev. 30-000093A 4/12/2017 VDD Internal POR TPWRT Power-up Timer MCLR TMCLR Internal RESET Oscillator Modes External Crystal TOST Oscillator Start-up Timer Oscillator FOSC Internal Oscillator Oscillator FOSC External Clock (EC) CLKIN FOSC Related Links Oscillator Module (with Fail-Safe Clock Monitor) 8.11 Memory Execution Violation A Memory Execution Violation Reset occurs if executing an instruction being fetched from outside the valid execution area. The different valid execution areas are defined as follows: * Flash Memory: The "Device Sizes and Addresses" table shows the addresses available on the PIC16(L)F18424/44 devices based on user Flash size. Execution outside this region generates a memory execution violation. * Storage Area Flash (SAF): If Storage Area Flash (SAF) is enabled , the SAF area is not a valid execution area. Prefetched instructions that are not executed do not cause memory execution violations. For example, a GOTO instruction in the last memory location will prefetch from an invalid location; this is not an error. If an instruction from an invalid location tries to execute, the memory violation is generated immediately, and any concurrent interrupt requests are ignored. When a memory execution violation is generated, the device is reset and flag MEMV is cleared in PCON1 to signal the cause. The flag needs to be set in code after a memory execution violation. Related Links (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 88 PIC16(L)F18424/44 Resets Program Memory Organization Storage Area Flash Memory Violation 8.12 Determining the Cause of a Reset Upon any Reset, multiple bits in the STATUS and PCON0 registers are updated to indicate the cause of the Reset. The following tables show the Reset conditions of these registers. Table 8-3. Reset Status Bits and Their Significance STOVF STKUNF RWDT RMCLR RI POR BOR TO PD MEMV Condition 0 0 1 1 1 0 x 1 1 1 Power-on Reset 0 0 1 1 1 0 x 0 x u Illegal, TO is set on POR 0 0 1 1 1 0 x x 0 u Illegal, PD is set on POR 0 0 u 1 1 u 0 1 1 u Brown-out Reset u u 0 u u u u 0 u u WWDT Reset u u u u u u u 0 0 u WWDT Wake-up from Sleep u u u u u u u 1 0 u Interrupt Wake-up from Sleep u u u 0 u u u u u 1 MCLR Reset during normal operation u u u 0 u u u 1 0 u MCLR Reset during Sleep u u u u 0 u u u u u RESET Instruction Executed 1 u u u u u u u u u Stack Overflow Reset (STVREN = 1) u 1 u u u u u u u u Stack Underflow Reset (STVREN = 1) u u u u u u u u u 0 Memory violation Reset Table 8-4. Reset Condition for Special Registers Program Counter STATUS Register PCON0 Register PCON1 Register Power-on Reset 0 ---1 1000 0011 110x ---- --1- Brown-out Reset 0 ---1 1000 0011 11u0 ---- --u- MCLR Reset during normal operation 0 -uuu uuuu uuuu 0uuu ---- --1- MCLR Reset during Sleep 0 ---1 0uuu uuuu 0uuu ---- --u- WWDT Time-out Reset 0 ---0 uuuu uuu0 uuuu ---- --u- PC + 1 ---0 0uuu uuuu uuuu ---- --u- Condition WWDT Wake-up from Sleep (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 89 PIC16(L)F18424/44 Resets Program Counter STATUS Register PCON0 Register PCON1 Register 0 ---u uuuu uu0u uuuu ---- --u- Interrupt Wake-up from Sleep PC + 1(1) ---1 0uuu uuuu uuuu ---- --u- RESET Instruction Executed 0 ---u uuuu uuuu u0uu ---- --u- Stack Overflow Reset (STVREN = 1) 0 ---u uuuu 1uuu uuuu ---- --u- Stack Underflow Reset (STVREN = 1) 0 ---u uuuu u1uu uuuu ---- --u- Memory Violation Reset (MEMV = 0) 0 -uuu uuuu uuuu uuuu ---- --0- Condition WWDT Window Violation Reset Legend: u = unchanged, x = unknown, -- = unimplemented bit, reads as `0'. Note: 1. When the wake-up is due to an interrupt and Global Enable bit (GIE) is set, the return address is pushed on the stack and PC is loaded with the interrupt vector (0004h) after execution of PC + 1. Related Links STATUS 8.13 Power Control (PCONx) Register The Power Control (PCONx) registers contain flag bits to differentiate between a: * * * * * * * * * Brown-out Reset (BOR) Power-on Reset (POR) Reset Instruction Reset (RI) MCLR Reset (RMCLR) Watchdog Timer Reset (RWDT) Watchdog Window Violation (WDTWV) Stack Underflow Reset (STKUNF) Stack Overflow Reset (STKOVF) Memory Violation Reset (MEMV) Hardware will change the corresponding register bit during the Reset process; if the Reset was not caused by the condition, the bit remains unchanged. Software should reset the bit to the inactive state after restart (hardware will not reset the bit). Software may also set any PCONx bit to the active state, so that user code may be tested, but no Reset action will be generated. Related Links Determining the Cause of a Reset PCON0 PCON1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 90 PIC16(L)F18424/44 Resets 8.14 Register Summary - BOR Control and Power Control Offset Name Bit Pos. 0x0811 BORCON 7:0 SBOREN 0x0812 Reserved 0x0813 PCON0 7:0 STKOVF 0x0814 PCON1 7:0 8.15 BORRDY STKUNF WDTWV RWDT RMCLR RI POR BOR MEMV Register Definitions: Power Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 91 PIC16(L)F18424/44 Resets 8.15.1 BORCON Name: Offset: BORCON 0x811 Brown-out Reset Control Register Bit Access Reset 7 6 5 4 3 2 1 0 SBOREN BORRDY R/W R 1 q Bit 7 - SBOREN Software Brown-out Reset Enable bit Reset States: POR/BOR = 1 All Other Resets = u Value -- 1 0 Condition If BOREN 01 If BOREN= 01 If BOREN= 01 Description SBOREN is read/write, but has no effect on the BOR. BOR Enabled BOR Disabled Bit 0 - BORRDY Brown-out Reset Circuit Ready Status bit Reset States: POR/BOR = q All Other Resets = u Value 1 0 Description The Brown-out Reset Circuit is active and armed The Brown-out Reset Circuit is disabled or is warming up Related Links CONFIG2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 92 PIC16(L)F18424/44 Resets 8.15.2 PCON0 Name: Offset: PCON0 0x813 Power Control Register 0 Bit Access Reset 7 6 5 4 3 2 1 0 STKOVF STKUNF WDTWV RWDT RMCLR RI POR BOR R/W/HS R/W/HS R/W/HC R/W/HC R/W/HC R/W/HC R/W/HC R/W/HC 0 0 1 1 1 1 0 q Bit 7 - STKOVF Stack Overflow Flag bit Reset States: POR/BOR = 0 All Other Resets = q Value 1 0 Description A Stack Overflow occurred (more CALLs than fit on the stack) A Stack Overflow has not occurred or set to `0' by firmware Bit 6 - STKUNF Stack Underflow Flag bit Reset States: POR/BOR = 0 All Other Resets = q Value 1 0 Description A Stack Underflow occurred (more RETURNs than CALLs) A Stack Underflow has not occurred or set to `0' by firmware Bit 5 - WDTWV Watchdog Window Violation Flag bit Reset States: POR/BOR = 1 All Other Resets = q Value 1 0 Description A WDT window violation has not occurred or set to `1' by firmware A CLRWDT instruction was issued when the WDT Reset window was closed (set to `0' in hardware when a WDT window violation Reset occurs) Bit 4 - RWDT WDT Reset Flag bit Reset States: POR/BOR = 1 All Other Resets = q Value 1 0 Description A WDT overflow/time-out Reset has not occurred or set to `1' by firmware A WDT overflow/time-out Reset has occurred (set to `0' in hardware when a WDT Reset occurs) Bit 3 - RMCLR MCLR Reset Flag bit Reset States: POR/BOR = 1 All Other Resets = q (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 93 PIC16(L)F18424/44 Resets Value 1 0 Description A MCLR Reset has not occurred or set to `1' by firmware A MCLR Reset has occurred (set to `0' in hardware when a MCLR Reset occurs) Bit 2 - RI RESET Instruction Flag bit Reset States: POR/BOR = 1 All Other Resets = q Value 1 0 Description A RESET instruction has not been executed or set to `1' by firmware A RESET instruction has been executed (set to `0' in hardware upon executing a RESET instruction) Bit 1 - POR Power-on Reset Status bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description No Power-on Reset occurred or set to `1' by firmware A Power-on Reset occurred (set to `0' in hardware when a Power-on Reset occurs) Bit 0 - BOR Brown-out Reset Status bit Reset States: POR/BOR = q All Other Resets = u Value 1 0 Description No Brown-out Reset occurred or set to `1' by firmware A Brown-out Reset occurred (set to `0' in hardware when a Brown-out Reset occurs) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 94 PIC16(L)F18424/44 Resets 8.15.3 PCON1 Name: Offset: PCON1 0x814 Power Control Register 1 Bit 7 6 5 4 3 2 1 0 MEMV Access R/W/HC Reset 1 Bit 1 - MEMV Memory Violation Flag bit Reset States: POR/BOR = 1 All Other Resets = u Value 1 0 Description No Memory Violation Reset occurred or set to `1' by firmware. A Memory Violation Reset occurred (set to `0' in hardware when a Memory Violation occurs) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 95 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9. Oscillator Module (with Fail-Safe Clock Monitor) 9.1 Overview The oscillator module has multiple clock sources and selection features that allow it to be used in a wide range of applications while maximizing performance and minimizing power consumption. The following figure illustrates a block diagram of the oscillator module. Clock sources can be supplied from external oscillators, quartz-crystal resonators and ceramic resonators. In addition, the system clock source can be supplied from one of two internal oscillators and PLL circuits, with a choice of speeds selectable via software. Additional clock features include: * * * Selectable system clock source between external or internal sources via software. Fail-Safe Clock Monitor (FSCM) designed to detect a failure of the external clock source (LP, XT, HS, ECH, ECM, ECL) and switch automatically to the internal oscillator. Oscillator Start-up Timer (OST) ensures stability of crystal oscillator sources. The RSTOSC bits of Configuration Word 1 determine the type of oscillator that will be used when the device runs after Reset, including when it is first powered up. The internal clock modes, LFINTOSC, HFINTOSC (set at 1 MHz), or HFINTOSC (set at 32 MHz) can be set through the RSTOSC bits. If an external clock source is selected, the FEXTOSC bits of Configuration Word 1 must be used in conjunction with the RSTOSC bits to select the External Clock mode. The external oscillator module can be configured in one of the following clock modes, by setting the FEXTOSC bits of Configuration Word 1: 1. 2. 3. 4. 5. 6. ECL - External Clock Low-Power mode ( 500 kHz) ECM - External Clock Medium-Power mode ( 8 MHz) ECH - External Clock High-Power mode ( 32 MHz) LP - 32 kHz Low-Power Crystal mode. XT - Medium Gain Crystal or Ceramic Resonator Oscillator mode (between 100 kHz and 4 MHz) HS - High Gain Crystal or Ceramic Resonator mode (above 4 MHz) The ECH, ECM, and ECL Clock modes rely on an external logic level signal as the device clock source. The LP, XT, and HS Clock modes require an external crystal or resonator to be connected to the device. Each mode is optimized for a different frequency range. The internal oscillator block produces low and high-frequency clock sources, designated LFINTOSC and HFINTOSC. Multiple device clock frequencies may be derived from these clock sources. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 96 Filename: Title: Last Edit: First Used: Notes: 10-000208G.vsd Simplified Clock Source Block Diagram 8/15/2016 PIC16(L)F15354/55 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) (R) Figure 9-1. Simplified PIC MCU Clock Source Block Diagram Rev. 10-000208M 5/17/2017 CLKIN/ OSC1 External Oscillator (EXTOSC) CLKOUT/ OSC2 CDIV<3:0> 4x PLL Mode SOSCIN/SOSCI Secondary Oscillator (SOSC) 512 PLL Block 256 111 2x PLL Mode LFINTOSC 31kHz Oscillator 9-bit Postscaler Divider SOSCO COSC<2:0> 001 010 100 101 110 000 128 64 32 16 8 4 2 011 1 HFINTOSC 1001 1000 Sleep 0111 System Clock 0110 0101 SYSCMD 0100 Peripheral Clock 0011 0010 Sleep 0001 Idle 0000 HFFRQ<2:0> 1 - 32 MHz Oscillator FSCM To Peripherals To Peripherals To Peripherals Related Links CONFIG1 9.2 Clock Source Types Clock sources can be classified as external or internal. External clock sources rely on external circuitry for the clock source to function. Examples are: oscillator modules (ECH, ECM, ECL mode), quartz crystal resonators or ceramic resonators (LP, XT and HS modes). There is also a secondary oscillator block which is optimized for a 32.768 kHz external clock source, which can be used as an alternate clock source. There are two internal oscillator blocks: * * HFINTOSC LFINTOSC The HFINTOSC can produce clock frequencies from 1-32 MHz, and is responsible for generating the two MFINTOSC frequencies (500 kHz and 32 kHz) that can be used by some peripherals. The LFINTOSC generates a 31 kHz clock frequency. There is a 4x PLL that can be used by the external oscillator. Additionally, there is a PLL that can be used by the HFINTOSC at certain frequencies. Related Links 4x PLL (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 97 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 2x PLL 9.2.1 External Clock Sources An external clock source can be used as the device system clock by performing one of the following actions: * * Program the RSTOSC bits in the Configuration Words to select an external clock source that will be used as the default system clock upon a device Reset. Write the NOSC and NDIV bits to switch the system clock source. Related Links Clock Switching 9.2.1.1 EC Mode The External Clock (EC) mode allows an externally generated logic level signal to be the system clock source. When operating in this mode, an external clock source is connected to the CLKIN/OSC1 input. OSC2/CLKOUT is available for general purpose I/O or CLKOUT. The following figure shows the pin connections for EC mode. EC mode has three power modes to select from through Configuration Words: * * * ECH - High power, 32 MHz ECM - Medium power, 8 MHz ECL - Low power, 0.1 MHz The Oscillator Start-up Timer (OST) is disabled when EC mode is selected. Therefore, there is no delay (R) in operation after a Power-on Reset (POR) or wake-up from Sleep. Because the PIC MCU design is fully static, stopping the external clock input will have the effect of halting the device while leaving all data intact. Upon restarting the external clock, the device will resume operation as if no time had elapsed. Figure 9-2. External Clock (EC) Mode Operation Rev. 30-000060A 4/6/2017 OSC1/CLKIN Clock from Ext. System PIC(R) MCU FOSC/4 or I/O(1) OSC2/CLKOUT Note: 1. Output depends upon CLKOUTEN bit of the Configuration Words (CONFIG1H). 9.2.1.2 LP, XT, HS Modes The LP, XT and HS modes support the use of quartz crystal resonators or ceramic resonators connected to OSC1 and OSC2 (Figure 9-3). The three modes select a low, medium or high gain setting of the internal inverter-amplifier to support various resonator types and speed. LP Oscillator mode selects the lowest gain setting of the internal inverter-amplifier. LP mode current consumption is the least of the three modes. This mode is designed to drive only 32.768 kHz tuning-fork type crystals (watch crystals). but can operate up to 100 kHz. XT Oscillator mode selects the intermediate gain setting of the internal inverter-amplifier. XT mode current consumption is the medium of the three modes. This mode is best suited to drive crystals and resonators with a frequency range up to 4 MHz. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 98 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) Filename: 10-000059A.vsd HS Oscillator mode selects the highest gain setting of the internal inverter-amplifier. HS mode current Title: QUARTZ CRYSTAL OPERATION (LP, XT OR HS MODE) Edit: modes. This 7/30/2013 consumption is the highest of theLast three mode is best suited for resonators that require First Used: PIC16F1508/9 operating frequencies up to 20 MHz. Note: Figure 9-3 and Figure 9-4 show typical circuits for quartz crystal and ceramic resonators, respectively. Figure 9-3. Quartz Crystal Operation (LP, XT or HS Mode) Rev. 10-000059A 7/30/2013 PIC(R) MCU OSC1/CLKIN C1 Quartz Crystal RS(1) C2 Note 1: To Internal Logic RF(2) Sleep OSC2/CLKOUT A series resistor (Rs) may be required for Note: quartz crystals with low drive level. 1. A series resistor (RS) may be required for ofquartz with low 2: The value RF variescrystals with the Oscillator mode drive level. selected (typically between 2 M and 10 M). 2. The value of RF varies with the Oscillator mode selected (typically between 2 M to 10 M). Figure 9-4. Ceramic Resonator Operation (XT or HS Mode) Rev. 30-000062A 4/6/2017 PIC(R) MCU OSC1/CLKIN C1 To Internal Logic RP(3) C2 Ceramic RS(1) Resonator RF(2) Sleep OSC2/CLKOUT Note: 1. A series resistor (RS) may be required for ceramic resonators with low drive level. 2. The value of RF varies with the Oscillator mode selected (typically between 2 M to 10 M). 3. An additional parallel feedback resistor (RP) may be required for proper ceramic resonator operation. 9.2.1.3 Oscillator Start-up Timer (OST) If the oscillator module is configured for LP, XT or HS modes, the Oscillator Start-up Timer (OST) counts 1024 oscillations from OSC1. This occurs following a Power-on Reset (POR), or a wake-up from Sleep. The OST ensures that the oscillator circuit, using a quartz crystal resonator or ceramic resonator, has started and is providing a stable system clock to the oscillator module. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 99 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.2.1.4 4x PLL The oscillator module contains a 4x PLL that can be used with the external clock sources to provide a system clock source. The input frequency for the PLL must fall within specifications. The PLL can be enabled for use by one of two methods: 1. Program the RSTOSC bits in the Configuration Word 1 to `010' (enable EXTOSC with 4x PLL). 2. Write the NOSC bits to `010' (enable EXTOSC with 4x PLL). Related Links OSCCON1 PLL Specifications 9.2.1.5 Secondary Oscillator The secondary oscillator is a separate oscillator block that can be used as an alternate system clock source. The secondary oscillator is optimized for 32.768 kHz, and can be used with an external crystal oscillator connected to the SOSCI and SOSCO device pins, or an external clock source connected to the SOSCIN pin. The secondary oscillator can be selected during run-time using clock switching. Figure 9-5. Quartz Crystal Operation (Secondary Oscillator) Rev. 30-000063A 4/6/2017 PIC(R) MCU SOSCI C1 To Internal Logic 32.768 kHz Quartz Crystal C2 SOSCO Note: 1. Quartz crystal characteristics vary according to type, package and manufacturer. The user should consult the manufacturer data sheets for specifications and recommended application. 2. Always verify oscillator performance over the VDD and temperature range that is expected for the application. 3. For oscillator design assistance, reference the following Microchip Application Notes: (R) (R) - AN826, "Crystal Oscillator Basics and Crystal Selection for PIC and PIC Devices" (DS00826) (R) - AN849, "Basic PIC Oscillator Design" (DS00849) - - - - (R) AN943, "Practical PIC Oscillator Analysis and Design" (DS00943) AN949, "Making Your Oscillator Work" (DS00949) TB097, "Interfacing a Micro Crystal MS1V-T1K 32.768 kHz Tuning Fork Crystal to a PIC16F690/SS" (DS91097) AN1288, "Design Practices for Low-Power External Oscillators" (DS01288) Related Links Clock Switching (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 100 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.2.2 Internal Clock Sources The device may be configured to use the internal oscillator block as the system clock by performing one of the following actions: * * Program the RSTOSC bits in Configuration Words to select the INTOSC clock source, which will be used as the default system clock upon a device Reset. Write the NOSC bits to switch the system clock source to the internal oscillator during run-time. In INTOSC mode, OSC1/CLKIN is available for general purpose I/O. OSC2/CLKOUT is available for general purpose I/O or CLKOUT. The function of the OSC2/CLKOUT pin is determined by the CLKOUTEN bit in Configuration Words. The internal oscillator block has two independent oscillators that can produce two internal system clock sources. 1. 2. The HFINTOSC (High-Frequency Internal Oscillator) is factory-calibrated and operates up to 32 MHz. The frequency of HFINTOSC can be selected through the OSCFRQ Frequency Selection register, and fine-tuning can be done via the OSCTUNE register. The LFINTOSC (Low-Frequency Internal Oscillator) is factory-calibrated and operates at 31 kHz. Related Links Clock Switching 9.2.2.1 HFINTOSC The High-Frequency Internal Oscillator (HFINTOSC) is a precision digitally-controlled internal clock source that produces a stable clock up to 32 MHz. The HFINTOSC can be enabled through one of the following methods: * * Programming the RSTOSC bits in Configuration Word 1 to `110' (FOSC = 1 MHz) or `000' (FOSC = 32 MHz) to set the oscillator upon device Power-up or Reset. Write to the NOSC bits during run-time. The HFINTOSC frequency can be selected by setting the HFFRQ bits. The NDIV bits allow for division of the HFINTOSC output from a range between 1:1 and 1:512. Related Links Clock Switching OSCCON1 OSCFRQ 9.2.2.2 MFINTOSC The module provides two (500 kHz and 31.25 kHz) constant clock outputs. These clocks are digital divisors of the HFINTOSC clock. Dynamic divider logic is used to provide constant MFINTOSC clock rates for all settings of HFINTOSC. The MFINTOSC cannot be used to drive the system but it is used to clock certain modules such as the Timers and WWDT. 9.2.2.3 2x PLL The oscillator module contains a PLL that can be used with the HFINTOSC clock source to provide a system clock source. The input frequency to the PLL is limited to 8, 12, or 16 MHz, which will yield a system clock source of 16, 24, or 32 MHz, respectively. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 101 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) The PLL may be enabled for use by one of two methods: 1. Program the RSTOSC bits in the Configuration Word 1 to `001' to enable the HFINTOSC (32 MHz). This setting configures the HFFRQ bits to `101' (16 MHz) and activates the 2x PLL. 2. Write `001' the NOSC bits to enable the 2x PLL, and write the correct value into the HFFRQ to select the desired system clock frequency. Related Links OSCCON1 OSCFRQ 9.2.2.4 Internal Oscillator Frequency Adjustment The internal oscillator is factory-calibrated. This internal oscillator can be adjusted in software by writing to the OSCTUNE register. The default value of the OSCTUNE register is 00h. The value is a 6-bit two's complement number. A value of 1Fh will provide an adjustment to the maximum frequency. A value of 20h will provide an adjustment to the minimum frequency. When the OSCTUNE register is modified, the oscillator frequency will begin shifting to the new frequency. Code execution continues during this shift. There is no indication that the shift has occurred. OSCTUNE does not affect the LFINTOSC frequency. Operation of features that depend on the LFINTOSC clock source frequency, such as the Power-up Timer (PWRT), WWDT, Fail-Safe Clock Monitor (FSCM) and peripherals, are not affected by the change in frequency. Related Links OSCTUNE 9.2.2.5 LFINTOSC The Low-Frequency Internal Oscillator (LFINTOSC) is a factory-calibrated 31 kHz internal clock source. The LFINTOSC is the frequency for the Power-up Timer (PWRT), Windowed Watchdog Timer (WWDT) and Fail-Safe Clock Monitor (FSCM). The LFINTOSC is enabled through one of the following methods: * * Programming the RSTOSC bits of Configuration Word 1 to enable LFINTOSC. Write to the NOSC bits during run-time. Related Links Clock Switching CONFIG1 OSCCON1 9.2.2.6 ADCRC (also referred to as FRC) The ADCRC is an oscillator dedicated to the ADC2 module. The ADCRC oscillator can be manually enabled using the ADOEN bit. The ADCRC runs at a fixed frequency of 600 kHz. ADCRC is automatically enabled if it is selected as the clock source for the ADC2 module. 9.2.2.7 Oscillator Status and Manual Enable The `ready' status of each oscillator is displayed in the OSCSTAT register. The oscillators can also be manually enabled through the OSCEN register. Manual enabling makes it possible to verify the operation of the EXTOSC or SOSC crystal oscillators. This can be achieved by enabling the selected oscillator, then watching the corresponding `ready' state of the oscillator in the OSCSTAT register. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 102 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) Related Links OSCSTAT OSCEN 9.2.2.8 HFOR and MFOR Bits The HFOR and MFOR bits indicate that the HFINTOSC and MFINTOSC is ready. These clocks are always valid for use at all times, but only accurate after they are ready. When a new value is loaded into the OSCFRQ register, the HFOR and MFOR bits will clear, and set again when the oscillator is ready. During pending OSCFRQ changes the MFINTOSC clock will stall at a high or a low state, until the HFINTOSC resumes operation. 9.3 Clock Switching The system clock source can be switched between external and internal clock sources via software using the New Oscillator Source (NOSC) and New Divider selection request (NDIV) bits. The following clock sources can be selected: * External Oscillator (EXTOSC) * High-Frequency Internal Oscillator (HFINTOSC) * Low-Frequency Internal Oscillator (LFINTOSC) * Secondary Oscillator (SOSC) * EXTOSC with 4x PLL * HFINTOSC with 2x PLL 9.3.1 New Oscillator Source (NOSC) and New Divider Selection Request (NDIV) Bits The New Oscillator Source (NOSC) and New Divider Selection Request (NDIV) bits select the system clock source and frequency that are used for the CPU and peripherals. When new values of NOSC and NDIV are written to OSCCON1, the current oscillator selection will continue to operate while waiting for the new clock source to indicate that it is stable and ready. In some cases, the newly requested source may already be in use, and is ready immediately. In the case of a divider-only change, the new and old sources are the same, so the old source will be ready immediately. The device may enter Sleep while waiting for the switch. When the new oscillator is ready, the New Oscillator Ready (NOSCR) bit is set and also the Clock Switch Interrupt Flag (CSWIF) bit of PIR1 sets. If Clock Switch Interrupts are enabled (CSWIE = 1), an interrupt will be generated at that time. The Oscillator Ready (ORDY) bit of OSCCON3 can also be polled to determine when the oscillator is ready in lieu of an interrupt. If the Clock Switch Hold (CSWHOLD) bit is clear, the oscillator switch will occur when the New Oscillator is READY bit (NOSCR) is set, and the interrupt (if enabled) will be serviced at the new oscillator setting. If CSWHOLD is set, the oscillator switch is suspended, while execution continues using the current (old) clock source. When the NOSCR bit is set, software should: * Set CSWHOLD = 0 so the switch can complete, or * Copy COSC into NOSC to abandon the switch. If DOZE is in effect, the switch occurs on the next clock cycle, whether or not the CPU is operating during that cycle. Changing the clock post-divider without changing the clock source (i.e., changing FOSC from 1 MHz to 2 MHz) is handled in the same manner as a clock source change, as described previously. The clock (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 103 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) source will already be active, so the switch is relatively quick. CSWHOLD must be clear (CSWHOLD = 0) for the switch to complete. The current COSC and CDIV are indicated in the OSCCON2 register up to the moment when the switch actually occurs, at which time OSCCON2 is updated and ORDY is set. NOSCR is cleared by hardware to indicate that the switch is complete. Related Links Clock Switch and Sleep OSCCON1 OSCCON2 OSCCON3 9.3.2 PLL Input Switch Switching between the PLL and any non-PLL source is managed as described above. The input to the PLL is established when NOSC selects the PLL, and maintained by the COSC setting. When NOSC and COSC select the PLL with different input sources, the system continues to run using the COSC setting, and the new source is enabled per NOSC. When the new oscillator is ready (and CSWHOLD = 0), system operation is suspended while the PLL input is switched and the PLL acquires lock. This provides a truly glitch-free clock switch operation. Important: If the PLL fails to lock, the FSCM will trigger. 9.3.3 Clock Switch and Sleep If OSCCON1 is written with a new value and the device is put to Sleep before the switch completes, the switch will not take place and the device will enter Sleep mode. When the device wakes from Sleep and the CSWHOLD bit is clear, the device will wake with the `new' clock active, and the Clock Switch Interrupt Flag bit (CSWIF) will be set. When the device wakes from Sleep and the CSWHOLD bit is set, the device will wake with the `old' clock active and the new clock will be requested again. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 104 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) Figure 9-6. Clock Switch (CSWHOLD = 0) Rev. 30-000064A 4/7/2016 OSCCON1 WRITTEN OSC #2 OSC #1 ORDY NOTE 2 NOSCR NOTE 1 CSWIF CSWHOLD USER CLEAR Note 1: CSWIF is asserted coincident with NOSCR; interrupt is serviced at OSC#2 speed. Note: 2: The assertion of NOSCR is hidden from the user because it appears only for the duration of the switch. 1. CSWIF is asserted coincident with NOSCR; interrupt is serviced at OSC#2 speed. 2. The assertion of NOSCR is hidden from the user because it appears only for the duration of the switch. Figure 9-7. Clock Switch (CSWHOLD = 1) Rev. 30-000065A 4/6/2017 OSCCON1 WRITTEN OSC #1 OSC #2 ORDY NOSCR CSWIF CSWHOLD NOTE 1 USER CLEAR Note 1: CSWIF is asserted coincident with NOSCR, and may be cleared before or after clearing CSWHOLD = 0. Note: 1. CSWIF is asserted coincident with NOSCR, and may be cleared before or after clearing CSWHOLD = 0. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 105 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) Figure 9-8. Clock Switch Abandoned Rev. 30-000066A 4/6/2017 OSCCON1 WRITTEN OSCCON1 WRITTEN OSC #1 ORDY NOTE 2 NOSCR NOTE 1 CSWIF CSWHOLD Note: 1. CSWIF may be cleared before or after rewriting OSCCON1; CSWIF is not automatically cleared. 2. ORDY = 0 if OSCCON1 does not match OSCCON2; a new switch will begin. 9.4 Fail-Safe Clock Monitor The Fail-Safe Clock Monitor (FSCM) allows the device to continue operating should the external oscillator fail. The FSCM is enabled by setting the FCMEN bit in the Configuration Words. The FSCM is applicable to all external Oscillator modes (LP, XT, HS, ECL/M/H and Secondary Oscillator). Figure 9-9. FSCM Block Diagram Clock Monitor Latch External Clock LFINTOSC Oscillator / 64 31 kHz D~32 usd 488 Hz D~2 msd S Q R Q Sample Clock 9.4.1 Rev. 30-000067A 4/6/2017 Clock Failure Detected Fail-Safe Detection The FSCM module detects a failed oscillator by comparing the external oscillator to the FSCM sample clock. The sample clock is generated by dividing the LFINTOSC by 64. See Figure 9-9. Inside the fail detector block is a latch. The external clock sets the latch on each falling edge of the external clock. The sample clock clears the latch on each rising edge of the sample clock. A failure is detected when an entire half-cycle of the sample clock elapses before the external clock goes low. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 106 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.4.2 Fail-Safe Operation When the external clock fails, the FSCM overwrites the COSC bits to select HFINTOSC (3'b110). The frequency of HFINTOSC would be determined by the previous state of the HFFRQ bits and the NDIV/ CDIV bits. The bit flag OSCFIF of the PIR1 register is set. Setting this flag will generate an interrupt if the OSCFIE bit of the PIE1 register is also set. The device firmware can then take steps to mitigate the problems that may arise from a failed clock. The system clock will continue to be sourced from the internal clock source until the device firmware successfully restarts the external oscillator and switches back to external operation, by writing to the NOSC and NDIV bits. 9.4.3 Fail-Safe Condition Clearing The Fail-Safe condition is cleared after a Reset, executing a SLEEP instruction or changing the NOSC and NDIV bits. When switching to the external oscillator or PLL, the OST is restarted. While the OST is running, the device continues to operate from the INTOSC selected in OSCCON1. When the OST times out, the Fail-Safe condition is cleared after successfully switching to the external clock source. The OSCFIF bit should be cleared prior to switching to the external clock source. If the Fail-Safe condition still exists, the OSCFIF flag will again become set by hardware. 9.4.4 Reset or Wake-up from Sleep The FSCM is designed to detect an oscillator failure after the Oscillator Start-up Timer (OST) has expired. The OST is used after waking up from Sleep and after any type of Reset. The OST is not used with the EC Clock modes so that the FSCM will be active as soon as the Reset or wake-up has completed. Figure 9-10. FSCM Timing Diagram Rev. 30-000068A 4/6/2017 Sample Clock Oscillator Failure System Clock Output Clock Monitor Output (Q) Failure Detected OSCFIF Test Test Test Note: The system clock is normally at a much higher frequency than the sample clock. The relative frequencies in this example have been chosen for clarity. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 107 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.5 Register Summary - OSC Offset Name Bit Pos. 0x088D OSCCON1 7:0 0x088E OSCCON2 7:0 0x088F OSCCON3 7:0 0x0890 OSCSTAT 7:0 EXTOR HFOR MFOR LFOR SOR ADOR 0x0891 OSCEN 7:0 EXTOEN HFOEN MFOEN LFOEN SOSCEN ADOEN 0x0892 OSCTUNE 7:0 0x0893 OSCFRQ 7:0 9.6 NOSC[2:0] NDIV[3:0] COSC[2:0] CSWHOLD SOSCPWR CDIV[3:0] ORDY NOSCR PLLR HFTUN[5:0] HFFRQ[2:0] Register Definitions: Oscillator Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 108 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.1 OSCCON1 Name: Offset: OSCCON1 0x88D Oscillator Control Register1 Bit 7 6 5 4 3 2 NOSC[2:0] Access Reset 1 0 NDIV[3:0] R/W R/W R/W R/W R/W R/W R/W f f f q q q q Bits 6:4 - NOSC[2:0] New Oscillator Source Request bits(1,2,3) The setting requests a source oscillator and PLL combination per Table 9-1. Table 9-1. NOSC Bit Settings NOSC<2:0> Clock Source 111 EXTOSC(5) 110 HFINTOSC(6) 101 LFINTOSC 100 SOSC 011 Reserved 010 EXTOSC + 4x PLL(5) 001 HFINTOSC + 2x PLL(6) 000 Reserved Bits 3:0 - NDIV[3:0] New Divider Selection Request bits(2,3,4) The setting determines the new postscaler division ratio per Table 9-2. Table 9-2. NDIV Bit Settings NDIV<3:0> Clock Divider 1111-1010 Reserved 1001 512 1000 256 0111 128 0110 64 0101 32 0100 16 0011 8 0010 4 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 109 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) NDIV<3:0> Clock Divider 0001 2 0000 1 Note: 1. The default value (f) is determined by the CONFIG1[RSTOSC] Configuration bits. 2. If NOSC is written with a reserved value, the operation is ignored and NOSC is not written. 3. When CONFIG1[CSWEN] = 0, this register is read-only and cannot be changed from the POR value. 4. When NOSC = 110 (HFINTOSC 1 MHz), the NDIV bits will default to `0010' upon Reset; for all other NOSC settings the NDIV bits will default to `0000' upon Reset. 5. 6. EXTOSC configured by CONFIG1[FEXTOSC]. HFINTOSC frequency is set with the FRQ bits of the OSCFRQ register. Related Links CONFIG1 PLL Specifications (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 110 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.2 OSCCON2 Name: Offset: OSCCON2 0x88E Oscillator Control Register 2 Bit 7 6 5 4 3 2 COSC[2:0] Access Reset 1 0 CDIV[3:0] RO RO RO RO RO RO RO n n n n n n n Bits 6:4 - COSC[2:0] Current Oscillator Source Select bits (read-only)(1,2) Indicates the current source oscillator and PLL combination as shown in the following table. Table 9-3. COSC Bit Settings COSC/NOSC Clock Source 111 EXTOSC(3) 110 HFINTOSC(4) 101 LFINTOSC 100 SOSC 011 Reserved 010 EXTOSC + 4x PLL(3) 001 HFINTOSC + 2x PLL(4) 000 Reserved Bits 3:0 - CDIV[3:0] Current Divider Select bits (read-only)(1,2) Indicates the current postscaler division ratio as shown in the following table. Table 9-4. CDIV Bit Settings CDIV/NDIV Clock Divider 1111-1010 Reserved 1001 512 1000 256 0111 128 0110 64 0101 32 0100 16 0011 8 0010 4 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 111 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) CDIV/NDIV Clock Divider 0001 2 0000 1 Note: 1. The POR value is the value present when user code execution begins. 2. The Reset value (n) is the same as the OSCCON1[NOSC/NDIV] bits. 3. EXTOSC configured by the CONFIG1[FEXTOSC] bits. 4. HFINTOSC frequency is configured with the FRQ bits of the OSCFRQ register Related Links CONFIG1 PLL Specifications (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 112 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.3 OSCCON3 Name: Offset: OSCCON3 0x88F Oscillator Control Register 3 Bit Access Reset 7 6 4 3 CSWHOLD SOSCPWR 5 ORDY NOSCR R/W/HC R/W RO RO 0 0 0 0 2 1 0 Bit 7 - CSWHOLD Clock Switch Hold bit Value 1 0 Description Clock switch will hold (with interrupt) when the oscillator selected by NOSC is ready Clock switch may proceed when the oscillator selected by NOSC is ready; when NOSCR becomes `1', the switch will occur Bit 6 - SOSCPWR Secondary Oscillator Power Mode Select bit Value 1 0 Description Secondary oscillator operating in High-Power mode Secondary oscillator operating in Low-Power mode Bit 4 - ORDY Oscillator Ready bit (read-only) Value 1 0 Description OSCCON1 = OSCCON2; the current system clock is the clock specified by NOSC A clock switch is in progress Bit 3 - NOSCR New Oscillator is Ready bit (read-only)(1) Value 1 0 Description A clock switch is in progress and the oscillator selected by NOSC indicates a ready condition A clock switch is not in progress, or the NOSC-selected oscillator is not yet ready Note: 1. If CSWHOLD = 0, the user may not see this bit set because the bit is set for less than one instruction cycle. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 113 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.4 OSCSTAT Name: Offset: OSCSTAT 0x890 Oscillator Status Register 1 Bit Access Reset 7 6 5 4 3 2 EXTOR HFOR MFOR LFOR SOR ADOR 1 PLLR 0 RO RO RO RO RO RO RO q q q q q q q Bit 7 - EXTOR EXTOSC (external) Oscillator Ready bit Value 1 0 Description The oscillator is ready to be used The oscillator is not enabled, or is not yet ready to be used Bit 6 - HFOR HFINTOSC Oscillator Ready bit Value 1 0 Description The oscillator is ready to be used The oscillator is not enabled, or is not yet ready to be used Bit 5 - MFOR MFINTOSC Oscillator Ready bit Value 1 0 Description The oscillator is ready to be used The oscillator is not enabled, or is not yet ready to be used Bit 4 - LFOR LFINTOSC Oscillator Ready bit Value 1 0 Description The oscillator is ready to be used The oscillator is not enabled, or is not yet ready to be used Bit 3 - SOR Secondary (Timer1) Oscillator Ready bit Value 1 0 Description The oscillator is ready to be used The oscillator is not enabled, or is not yet ready to be used Bit 2 - ADOR ADC Oscillator Ready bit Value 1 0 Description The oscillator is ready to be used The oscillator is not enabled, or is not yet ready to be used Bit 0 - PLLR PLL Ready bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 114 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) Value 1 0 Description The PLL is ready to be used The PLL is not enabled, the required input source is not ready, or the PLL is not locked. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 115 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.5 OSCEN Name: Offset: OSCEN 0x891 Oscillator Manual Enable Register Bit Access Reset 7 6 5 4 3 2 EXTOEN HFOEN MFOEN LFOEN SOSCEN ADOEN R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 1 0 Bit 7 - EXTOEN External Oscillator Manual Request Enable bit Value 1 0 Description EXTOSC is explicitly enabled, operating as specified by CONFIG1[FEXTOSC] EXTOSC is only enabled if requested by a peripheral Bit 6 - HFOEN HFINTOSC Oscillator Manual Request Enable bit Value 1 0 Description HFINTOSC is explicitly enabled, operating as specified by OSCFRQ HFINTOSC is only enabled if requested by a peripheral Bit 5 - MFOEN MFINTOSC (500 kHz/31.25 kHz) Oscillator Manual Request Enable bit (Derived from HFINTOSC) Value 1 0 Description MFINTOSC is explicitly enabled MFINTOSC is only enabled if requested by a peripheral Bit 4 - LFOEN LFINTOSC (31 kHz) Oscillator Manual Request Enable bit Value 1 0 Description LFINTOSC is explicitly enabled LFINTOSC is only enabled if requested by a peripheral Bit 3 - SOSCEN Secondary Oscillator Manual Request Enable bit Value 1 0 Description Secondary Oscillator is explicitly enabled, operating as specified by SOSCPWR Secondary Oscillator is only enabled if requested by a peripheral Bit 2 - ADOEN ADC Oscillator Manual Request Enable bit Value 1 0 Description ADC oscillator is explicitly enabled ADC oscillator is only enabled if requested by a peripheral Related Links CONFIG1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 116 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.6 OSCTUNE Name: Offset: OSCTUNE 0x892 HFINTOSC Tuning Register Bit 7 6 5 4 3 2 1 0 HFTUN[5:0] Access Reset R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 5:0 - HFTUN[5:0] HFINTOSC Frequency Tuning bits Value 01 1111 00 0000 10 0000 Description Maximum frequency Center frequency. Oscillator module is running at the calibrated frequency (default value). Minimum frequency (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 117 PIC16(L)F18424/44 Oscillator Module (with Fail-Safe Clock Monitor) 9.6.7 OSCFRQ Name: Offset: OSCFRQ 0x893 HFINTOSC Frequency Selection Register Bit 7 6 5 4 3 2 1 0 HFFRQ[2:0] Access Reset R/W R/W R/W q q q Bits 2:0 - HFFRQ[2:0] HFINTOSC Frequency Selection bits FRQ<2:0> Nominal Frequency (MHz) (NOSC = 110) 2x PLL Frequency (MHz) (NOSC = 001) 111 Reserved 110 32 101 16 32 100 12 24 011 8 16 010 4 001 2 000 1 Reserved Reserved Note: 1. When RSTOSC = 110 (HFINTOSC 1 MHz), the FRQ bits will default to `010' upon Reset; when RSTOSC = 001 (HFINTOSC 32 MHz), the FRQ bits will default to `101' upon Reset. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 118 PIC16(L)F18424/44 Interrupts 10. Interrupts The interrupt feature allows certain events to preempt normal program flow. Firmware is used to determine the source of the interrupt and act accordingly. Some interrupts can be configured to wake the MCU from Sleep mode. This chapter contains the following information for Interrupts: * * Operation Interrupt Latency * * * Interrupts During Sleep INT Pin Automatic Context Saving Many peripherals produce interrupts. Refer to the corresponding chapters for details. Filename: 10-000010C.vsd Title: diagram of Interrupt Logic logic is shown below. A block the interrupt Last Edit: 10/12/2016 First 10-1. Used: Interrupt PIC16(L)F191XX Figure Logic (MVAJ) Rev. 10-000010C 10/12/2016 TMR0IF TMR0IE Peripheral Interrupts (ADIF) PIR1 <0> (ADIE) PIE1 <0> Wake-up (If in Sleep mode) INTF INTE IOCIF IOCIE Interrupt to CPU PEIE PIRn PIEn 10.1 GIE Operation Interrupts are disabled upon any device Reset. They are enabled by setting the following bits: * GIE bit of the INTCON register * * Interrupt Enable bit(s) of the PIEx[y] registers for the specific interrupt event(s) PEIE bit of the INTCON register (if the Interrupt Enable bit of the interrupt event is contained in the PIEx registers) The PIR registers contain the individual flag bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are 9 PIR registers. The following events happen when an interrupt event occurs while the GIE bit is set: * Current prefetched instruction is flushed * GIE bit is cleared * Current Program Counter (PC) is pushed onto the stack (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 119 PIC16(L)F18424/44 Interrupts * * Critical registers are automatically saved to the shadow registers (see "Automatic Context Saving") PC is loaded with the interrupt vector 0004h The firmware within the Interrupt Service Routine (ISR) should determine the source of the interrupt by polling the interrupt flag bits. The interrupt flag bits must be cleared before exiting the ISR to avoid repeated interrupts. Because the GIE bit is cleared, any interrupt that occurs while executing the ISR will be recorded through its interrupt flag, but will not cause the processor to redirect to the interrupt vector. The RETFIE instruction exits the ISR by popping the previous address from the stack, restoring the saved context from the shadow registers and setting the GIE bit. For additional information on a specific interrupts operation, refer to its peripheral chapter. Important: 1. Individual interrupt flag bits are set, regardless of the state of any other enable bits. 2. All interrupts will be ignored while the GIE bit is cleared. Any interrupt occurring while the GIE bit is clear will be serviced when the GIE bit is set again. Related Links Automatic Context Saving 10.2 Interrupt Latency Filename: 10-000269E.vsd Interrupt latency is defined as the time from when the interrupt event occurs to the time code execution at Title: INT LATENCY - ONE CYCLE the interrupt begins. The interrupt is sampled during Q1 of the instruction cycle. The actual Last Edit: vector 8/31/2016 First Used: PIC16(L)F18325/45 (MFAH) interrupt latency then depends on the instruction that is executing at the time the interrupt is detected. Notes: See the following figures for more details. Figure 10-2. Interrupt Latency Rev. 10-000269E 8/31/2016 OSC1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 CLKOUT INT pin Valid Interrupt window(1) Fetch PC - 1 Execute PC - 2 PC PC - 1 Indeterminate Latency(2) Note: 1 Cycle Instruction at PC PC = 0x0004 PC + 1 PC NOP NOP PC = 0x0005 PC = 0x0006 PC = 0x0004 PC = 0x0005 Latency Note 1: An interrupt may occur at any time during the interrupt window. 2: Since an interrupt may occur any time during the interrupt window, the actual latency can vary. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 120 PIC16(L)F18424/44 Interrupts 1. 2. An interrupt may occur at any time during the interrupt window. Since an interrupt may occur any time during the interrupt window, the actual latency can vary. Figure 10-3. INT Pin Interrupt Timing Rev. 30-000150A 6/27/2017 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 (4) INT pin (1) (1) INTF Interrupt Latency (2) (5) GIE INSTRUCTION FLOW PC Instruction Fetched Instruction Executed PC Inst (PC) Inst (PC - 1) PC + 1 Inst (PC + 1) Inst (PC) PC + 1 -- For ced NOP 0004h Inst (0004h) For ced NOP 0005h Inst (0005h) Inst (0004h) Note: 1. INTF flag is sampled here (every Q1). 2. Asynchronous interrupt latency = 3-5 TCY. Synchronous latency = 3-4 TCY, where TCY = instruction cycle time. Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction. 3. For minimum width of INT pulse, refer to AC specifications in the "Electrical Specifications" section. 4. INTF may be set any time during the Q4-Q1 cycles. 10.3 Interrupts During Sleep Interrupts can be used to wake from Sleep. To wake from Sleep, the peripheral must be able to operate without the system clock. The interrupt source must have the appropriate Interrupt Enable bit(s) set prior to entering Sleep. On waking from Sleep, if the GIE bit is also set, the processor will branch to the interrupt vector. Otherwise, the processor will continue executing instructions after the SLEEP instruction. The instruction directly after the SLEEP instruction will always be executed before branching to the ISR. Related Links Power-Saving Operation Modes 10.4 INT Pin The INT pin can be used to generate an asynchronous edge-triggered interrupt. Refer to Figure 10-3. This interrupt is enabled by setting the INTE bit of the PIE0 register. The INTEDG bit of the INTCON register determines on which edge the interrupt will occur. When the INTEDG bit is set, the rising edge will cause the interrupt. When the INTEDG bit is clear, the falling edge will cause the interrupt. The INTF (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 121 PIC16(L)F18424/44 Interrupts bit of the PIR0 register will be set when a valid edge appears on the INT pin. If the GIE and INTE bits are also set, the processor will redirect program execution to the interrupt vector. 10.5 Automatic Context Saving Upon entering an interrupt, the return PC address is saved on the stack. Additionally, the following registers are automatically saved in the shadow registers: * W register * STATUS register (except for TO and PD) * BSR register * FSR registers * PCLATH register Upon exiting the Interrupt Service Routine, these registers are automatically restored. Any modifications to these registers during the ISR will be lost. If modifications to any of these registers are desired, the corresponding shadow register should be modified and the value will be restored when exiting the ISR. The shadow registers are available in Bank 63 and are readable and writable. Depending on the user's application, other registers may also need to be saved. Related Links Register Definitions: Shadow Registers (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 122 PIC16(L)F18424/44 Interrupts 10.6 Register Summary - Interrupt Control Offset Name Bit Pos. 0x070C PIR0 7:0 0x070D PIR1 7:0 0x070E PIR2 7:0 0x070F PIR3 7:0 RC1IF TX1IF 0x0710 PIR4 7:0 TMR6IF TMR5IF 0x0711 PIR5 7:0 CL24IF CLC1IF 0x0712 PIR6 7:0 0x0713 PIR7 7:0 NVMIF NCO1IF 0x0714 PIR8 7:0 0x0715 Reserved 0x0716 PIE0 7:0 0x0717 PIE1 7:0 0x0718 PIE2 7:0 0x0719 PIE3 7:0 0x071A PIE4 7:0 0x071B PIE5 7:0 0x071C PIE6 7:0 0x071D PIE7 7:0 0x071E PIE8 7:0 10.7 TMR0IF OSFIF CLC4IF IOCIF INTF CSWIF ADTIF ADIF ZCDIF C2IF C1IF CLC3IF TMR4IF CCP4IF BCL1IF SSP1IF TMR3IF TMR2IF TMR1IF TMR5GIF TMR3GIF TMR1GIF CCP3IF CCP2IF CCP1IF CWG2IF CWG1IF SMT1PWAIF SMT1PRAIF TMR0IE OSFIE CLC4IE IOCIE SMT1IF INTE CSWIE ADTIE ZCDIE C2IE C1IE BCL1IE SSP1IE CLC3IE RC1IE TX1IE TMR6IE TMR5IE CLC2IE CLC1IE TMR4IE CCP4IE NVMIE NCO1IE ADIE TMR3IE TMR2IE TMR1IE TMR5GIE TMR3GIE TMR1GIE CCP3IE CCP2IE CCP1IE CWG2IE CWG1IE SMT1PWAIE SMT1PRAIE SMT1IE Register Definitions: Interrupt Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 123 PIC16(L)F18424/44 Interrupts 10.7.1 INTCON Name: Offset: INTCON 0x00B Interrupt Control Register Bit Access Reset 7 6 GIE PEIE 5 4 3 2 1 INTEDG 0 R/W R/W R/W 0 0 1 Bit 7 - GIE Global Interrupt Enable bit Value 1 0 Description Enables all active interrupts Disables all interrupts Bit 6 - PEIE Peripheral Interrupt Enable bit Value 1 0 Description Enables all active peripheral interrupts Disables all peripheral interrupts Bit 0 - INTEDG External Interrupt Edge Select bit Value 1 0 Description Interrupt on rising edge of INT pin Interrupt on falling edge of INT pin Important: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 124 PIC16(L)F18424/44 Interrupts 10.7.2 PIE0 Name: Offset: PIE0 0x716 Peripheral Interrupt Enable Register 0 Bit 7 6 Access Reset 5 4 TMR0IE IOCIE 3 2 1 INTE 0 R/W R/W R/W 0 0 0 Bit 5 - TMR0IE Timer0 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 4 - IOCIE Interrupt-on-Change Enable bit Value 1 0 Description Enabled Disabled Bit 0 - INTE External Interrupt Enable bit(1) Value 1 0 Description Enabled Disabled Note: 1. The External Interrupt INT pin is selected by INTPPS. Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by PIE1PIE8. Interrupt sources controlled by the PIE0 register do not require PEIE to be set in order to allow interrupt vectoring (when GIE is set). Related Links xxxPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 125 PIC16(L)F18424/44 Interrupts 10.7.3 PIE1 Name: Offset: PIE1 0x717 Peripheral Interrupt Enable Register 1 Bit Access Reset 7 6 1 0 OSFIE CSWIE 5 4 3 2 ADTIE ADIE R/W R/W R/W R/W 0 0 0 0 Bit 7 - OSFIE Oscillator Fail Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 6 - CSWIE Clock-Switch Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - ADTIE ADC Threshold Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - ADIE ADC Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 126 PIC16(L)F18424/44 Interrupts 10.7.4 PIE2 Name: Offset: PIE2 0x718 Peripheral Interrupt Enable Register 2 Bit 7 Access Reset 1 0 ZCDIE 6 5 4 3 2 C2IE C1IE R/W R/W R/W 0 0 0 Bit 6 - ZCDIE Zero-Cross Detect Interrupt Enable bit Value 1 0 Description Enabled Disabled Bits 0, 1 - CnIE Comparator `n' Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 127 PIC16(L)F18424/44 Interrupts 10.7.5 PIE3 Name: Offset: PIE3 0x719 Peripheral Interrupt Enable Register 3 Bit 7 6 Access Reset 5 4 1 0 RC1IE TX1IE 3 2 BCL1IE SSP1IE R/W R/W R/W R/W 0 0 0 0 Bit 5 - RCnIE EUSARTn Receive Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 4 - TXnIE EUSARTn Transmit Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - BCLnIE MSSPn Bus Collision Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - SSPnIE Synchronous Serial Port `n' Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 128 PIC16(L)F18424/44 Interrupts 10.7.6 PIE4 Name: Offset: PIE4 0x71A Peripheral Interrupt Enable Register 4 Bit 7 6 Access Reset 5 4 3 2 1 0 TMR6IE TMR5IE TMR4IE TMR3IE TMR2IE TMR1IE R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bit 5 - TMR6IE TMR6 to PR6 Match Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 4 - TMR5IE TMR5 Overflow Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 3 - TMR4IE TMR4 to PR4 Match Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 2 - TMR3IE TMR3 Overflow Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - TMR2IE TMR2 to PR2 Match Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - TMR1IE TMR1 Overflow Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 129 PIC16(L)F18424/44 Interrupts 10.7.7 PIE5 Name: Offset: PIE5 0x71B Peripheral Interrupt Enable Register 5 Bit Access Reset 7 6 5 4 2 1 0 CLC4IE CLC3IE CLC2IE CLC1IE 3 TMR5GIE TMR3GIE TMR1GIE R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 Bit 7 - CLC4IE CLC4 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 6 - CLC3IE CLC3 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 5 - CLC2IE CLC2 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 4 - CLC1IE CLC1 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 2 - TMR5GIE TMR5 Gate Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - TMR3GIE TMR3 Gate Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - TMR1GIE TMR1 Gate Interrupt Enable bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 130 PIC16(L)F18424/44 Interrupts Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 131 PIC16(L)F18424/44 Interrupts 10.7.8 PIE6 Name: Offset: PIE6 0x71C Peripheral Interrupt Enable Register 6 Bit 7 6 5 Access Reset 4 3 2 1 0 CCP4IE CCP3IE CCP2IE CCP1IE R/W R/W R/W R/W 0 0 0 0 Bit 3 - CCP4IE CCP4 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 2 - CCP3IE CCP3 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - CCP2IE CCP2 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - CCP1IE CCP1 Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 132 PIC16(L)F18424/44 Interrupts 10.7.9 PIE7 Name: Offset: PIE7 0x71D Peripheral Interrupt Enable Register 7 Bit 7 6 Access Reset 5 4 1 0 NVMIE NCO1IE 3 2 CWG2IE CWG1IE R/W R/W R/W R/W 0 0 0 0 Bit 5 - NVMIE NVM Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 4 - NCO1IE NCO Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - CWG2IE CWG2 Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - CWG1IE CWG1 Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 133 PIC16(L)F18424/44 Interrupts 10.7.10 PIE8 Name: Offset: PIE8 0x71E Peripheral Interrupt Enable Register 8 Bit 7 6 5 4 3 2 1 0 SMT1PWAIE SMT1PRAIE SMT1IE R/W R/W R/W 0 0 0 Access Reset Bit 2 - SMT1PWAIE SMT1 Pulse-width Acquisition Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 1 - SMT1PRAIE SMT1 Period Acquisition Interrupt Enable bit Value 1 0 Description Enabled Disabled Bit 0 - SMT1IE SMT1 Counter Overflow Interrupt Enable bit Value 1 0 Description Enabled Disabled Note: Bit PEIE of the INTCON register must be set to enable any peripheral interrupt controlled by registers PIE1-PIE8. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 134 PIC16(L)F18424/44 Interrupts 10.7.11 PIR0 Name: Offset: PIR0 0x70C Peripheral Interrupt Request (Flag) Register 0 Bit 7 6 Access Reset 5 4 TMR0IF IOCIF 3 2 1 INTF 0 R/W/HS RO R/W/HS 0 0 0 Bit 5 - TMR0IF Timer0 Interrupt Flag bit Value 1 0 Description TMR0 register has overflowed (must be cleared by software) TMR0 register has not overflowed Bit 4 - IOCIF Interrupt-on-Change Flag bit(2) Value 1 0 Description One or more of the IOCAF-IOCEF register bits are currently set, indicating an enabled edge was detected by the IOC module. None of the IOCAF-IOCEF register bits are currently set Bit 0 - INTF External Interrupt Flag bit(1) Value 1 0 Description External Interrupt has occurred External Interrupt has not occurred Note: 1. The External Interrupt INT pin is selected by INTPPS. 2. The IOCIF bit is the logical OR of all the IOCAF-IOCEF flags. Therefore, to clear the IOCIF flag, application firmware must clear all of the lower level IOCAF-IOCEF register bits. Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. Related Links xxxPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 135 PIC16(L)F18424/44 Interrupts 10.7.12 PIR1 Name: Offset: PIR1 0x70D Peripheral Interrupt Request (Flag) Register 1 Bit Access Reset 7 6 1 0 OSFIF CSWIF 5 4 3 2 ADTIF ADIF R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 Bit 7 - OSFIF Oscillator Fail Interrupt Flag bit Value 1 0 Description Oscillator fail-safe interrupt has occurred (must be cleared in software) No oscillator fail-safe interrupt Bit 6 - CSWIF Clock-Switch Complete Interrupt Flag bit Value 1 0 Description The clock switch module indicates an interrupt condition and is ready to complete the clock switch operation (must be cleared in software) The clock switch does not indicate an interrupt condition Bit 1 - ADTIF ADC Threshold Interrupt Flag bit Value 1 0 Description An A/D conversion or complex operation has completed (must be cleared in software) An A/D conversion or complex operation is not complete Bit 0 - ADIF ADC Interrupt Flag bit Value 1 0 Description An A/D conversion or complex operation has completed (must be cleared in software) An A/D conversion or complex operation is not complete Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 136 PIC16(L)F18424/44 Interrupts 10.7.13 PIR2 Name: Offset: PIR2 0x70E Peripheral Interrupt Request (Flag) Register 2 Bit 7 Access Reset 1 0 ZCDIF 6 5 4 3 2 C2IF C1IF R/W/HS R/W/HS R/W/HS 0 0 0 Bit 6 - ZCDIF Zero-Cross Detect Interrupt Flag bit Value 1 0 Description An enabled rising and/or falling ZCD1 event has been detected (must be cleared in software) No ZCD1 event has occurred Bits 0, 1 - CnIF Comparator `n' Interrupt Flag bit Value 1 0 Description Comparator Cn interrupt asserted (must be cleared in software) Comparator Cn interrupt not asserted Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 137 PIC16(L)F18424/44 Interrupts 10.7.14 PIR3 Name: Offset: PIR3 0x70F Peripheral Interrupt Request (Flag) Register 3 Bit 7 6 Access Reset 5 4 1 0 RC1IF TX1IF 3 2 BCL1IF SSP1IF RO/HS RO/HS R/W/HS R/W/HS 0 0 0 0 Bit 5 - RCnIF EUSARTn Receive Interrupt Flag bit(1) Value 1 0 Description The EUSARTn receive buffer is not empty (contains at least one byte) The EUSARTn receive buffer is empty Bit 4 - TXnIF EUSARTn Transmit Interrupt Flag bit(2) Value 1 0 Description The EUSARTn transmit buffer contains at least one unoccupied space The EUSARTn transmit buffer is currently full. The application firmware should not write to TXnREG again, until more room becomes available in the transmit buffer. Bit 1 - BCLnIF MSSPn Bus Collision Interrupt Flag bit Value 1 0 Description A bus collision was detected (must be cleared in software) No bus collision was detected Bit 0 - SSPnIF Synchronous Serial Port `n' Interrupt Flag bit Value 1 0 Description The Transmission/Reception/Bus Condition is complete (must be cleared in software) Waiting for the Transmission/Reception/Bus Condition in progress Note: 1. The RCnIF flag is a read-only bit. To clear the RCnIF flag, the firmware must read from RCnREG enough times to remove all bytes from the receive buffer. 2. The TXnIF flag is a read-only bit, indicating if there is room in the transmit buffer. To clear the TXnIF flag, the firmware must write enough data to TXnREG to completely fill all available bytes in the buffer. The TXnIF flag does not indicate transmit completion (use TRMT for this purpose instead). Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 138 PIC16(L)F18424/44 Interrupts 10.7.15 PIR4 Name: Offset: PIR4 0x710 Peripheral Interrupt Request (Flag) Register 4 Bit 7 6 Access Reset 5 4 3 2 1 0 TMR6IF TMR5IF TMR4IF TMR3IF TMR2IF TMR1IF R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 0 0 Bit 5 - TMR6IF TMR6 to PR6 Match Interrupt Flag bit Value 1 0 Description The TMR6 postscaler overflowed, or in 1:1 mode, a TMR6 to PR6 match occurred (must be cleared in software) No TMR6 event has occurred Bit 4 - TMR5IF TMR5 Overflow Interrupt Flag bit Value 1 0 Description TMR5 register overflowed (must be cleared in software) TMR5 register did not overflow Bit 3 - TMR4IF TMR4 to PR4 Match Interrupt Flag bit Value 1 0 Description The TMR4 postscaler overflowed, or in 1:1 mode, a TMR4 to PR4 match occurred (must be cleared in software) No TMR4 event has occurred Bit 2 - TMR3IF TMR3 Overflow Interrupt Flag bit Value 1 0 Description TMR3 register overflowed (must be cleared in software) TMR3 register did not overflow Bit 1 - TMR2IF TMR2 to PR2 Match Interrupt Flag bit Value 1 0 Description The TMR2 postscaler overflowed, or in 1:1 mode, a TMR2 to PR2 match occurred (must be cleared in software) No TMR2 event has occurred Bit 0 - TMR1IF TMR1 Overflow Interrupt Flag bit Value 1 0 Description TMR1 register overflowed (must be cleared in software) TMR1 register did not overflow (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 139 PIC16(L)F18424/44 Interrupts Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 140 PIC16(L)F18424/44 Interrupts 10.7.16 PIR5 Name: Offset: PIR5 0x711 Peripheral Interrupt Request (Flag) Register 5 Bit Access Reset 7 6 5 4 2 1 0 CLC4IF CLC3IF CL24IF CLC1IF 3 TMR5GIF TMR3GIF TMR1GIF R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 0 0 0 Bit 7 - CLC4IF CLC4 Interrupt Flag bit Value 1 0 Description A CLC4OUT interrupt condition has occurred (must be cleared in software) No CLC4 interrupt event has occurred Bit 6 - CLC3IF CLC3 Interrupt Flag bit Value 1 0 Description A CLC3OUT interrupt condition has occurred (must be cleared in software) No CLC3 interrupt event has occurred Bit 5 - CL24IF CLC2 Interrupt Flag bit Value 1 0 Description A CLC2OUT interrupt condition has occurred (must be cleared in software) No CLC2 interrupt event has occurred Bit 4 - CLC1IF CLC1 Interrupt Flag bit Value 1 0 Description A CLC1OUT interrupt condition has occurred (must be cleared in software) No CLC1 interrupt event has occurred Bit 2 - TMR5GIF TMR5 Gate Interrupt Flag bit Value 1 0 Description The Timer5 Gate has gone inactive (the acquisition is complete) The Timer5 Gate has not gone inactive Bit 1 - TMR3GIF TMR3 Gate Interrupt Flag bit Value 1 0 Description The Timer3 Gate has gone inactive (the acquisition is complete) The Timer3 Gate has not gone inactive Bit 0 - TMR1GIF TMR1 Gate Interrupt Flag bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 141 PIC16(L)F18424/44 Interrupts Value 1 0 Description The Timer1 Gate has gone inactive (the acquisition is complete) The Timer1 Gate has not gone inactive Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 142 PIC16(L)F18424/44 Interrupts 10.7.17 PIR6 Name: Offset: PIR6 0x712 PIR6 Peripheral Interrupt Request (Flag) Register 6 Bit 7 6 5 Access Reset 4 3 2 1 0 CCP4IF CCP3IF CCP2IF CCP1IF R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 Bit 3 - CCP4IF CCP4 Interrupt Flag bit Value 1 0 1 0 1 0 Condition Capture mode Capture mode Compare mode Compare mode PWM mode PWM mode Description Capture occurred (must be cleared in software) Capture did not occur Compare match occurred (must be cleared in software) Compare match did not occur Output trailing edge occurred (must be cleared in software) Output trailing edge did not occur Bit 2 - CCP3IF CCP3 Interrupt Flag bit Value 1 0 1 0 1 0 Condition Capture mode Capture mode Compare mode Compare mode PWM mode PWM mode Description Capture occurred (must be cleared in software) Capture did not occur Compare match occurred (must be cleared in software) Compare match did not occur Output trailing edge occurred (must be cleared in software) Output trailing edge did not occur Bit 1 - CCP2IF CCP2 Interrupt Flag bit Value 1 0 1 0 1 0 Condition Capture mode Capture mode Compare mode Compare mode PWM mode PWM mode Description Capture occurred (must be cleared in software) Capture did not occur Compare match occurred (must be cleared in software) Compare match did not occur Output trailing edge occurred (must be cleared in software) Output trailing edge did not occur Bit 0 - CCP1IF CCP1 Interrupt Flag bit Value 1 0 1 0 Condition Capture mode Capture mode Compare mode Compare mode (c) 2018 Microchip Technology Inc. Description Capture occurred (must be cleared in software) Capture did not occur Compare match occurred (must be cleared in software) Compare match did not occur Datasheet Preliminary DS40002000A-page 143 PIC16(L)F18424/44 Interrupts Value 1 0 Condition PWM mode PWM mode Description Output trailing edge occurred (must be cleared in software) Output trailing edge did not occur Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 144 PIC16(L)F18424/44 Interrupts 10.7.18 PIR7 Name: Offset: PIR7 0x713 Peripheral Interrupt Request (Flag) Register 7 Bit 7 6 Access Reset 5 4 1 0 NVMIF NCO1IF 3 2 CWG2IF CWG1IF R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 Bit 5 - NVMIF NVM Interrupt Flag bit Value 1 0 Description The requested NVM operation has completed NVM interrupt not asserted Bit 4 - NCO1IF Numerically Controlled Oscillator (NCO) Interrupt Flag bit Value 1 0 Description The NCO has rolled over No NCO interrupt event has occurred Bit 1 - CWG2IF CWG2 Interrupt Flag bit Value 1 0 Description CWG2 has gone into shutdown CWG2 is operating normally, or interrupt cleared Bit 0 - CWG1IF CWG1 Interrupt Flag bit Value 1 0 Description CWG1 has gone into shutdown CWG1 is operating normally, or interrupt cleared Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 145 PIC16(L)F18424/44 Interrupts 10.7.19 PIR8 Name: Offset: PIR8 0x714 Peripheral Interrupt Request (Flag) Register 8 Bit 7 6 5 4 3 2 1 0 SMT1PWAIF SMT1PRAIF SMT1IF R/W/HS R/W/HS R/W/HS 0 0 0 Access Reset Bit 2 - SMT1PWAIF SMT1 Pulse-Width Acquisition Interrupt Flag bit Value 1 0 Description Interrupt has occurred (must be cleared by software) Interrupt event has not occurred Bit 1 - SMT1PRAIF SMT1 Period Acquisition Interrupt Flag bit Value 1 0 Description Interrupt has occurred (must be cleared by software) Interrupt event has not occurred Bit 0 - SMT1IF SMT1 Interrupt Flag bit Value 1 0 Description Interrupt has occurred (must be cleared by software) Interrupt event has not occurred Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the Global Enable bit, GIE, of the INTCON appropriate interrupt flag bits are clear prior to enabling an interrupt. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 146 PIC16(L)F18424/44 Power-Saving Operation Modes 11. Power-Saving Operation Modes The purpose of the Power-Down modes is to reduce power consumption. There are three Power-Down modes: * * * 11.1 Doze mode Sleep mode Idle mode Doze Mode Doze mode allows for power saving by reducing CPU operation and program memory (PFM) access, without affecting peripheral operation. Doze mode differs from Sleep mode because the bandgap and system oscillators continue to operate, while only the CPU and PFM are affected. The reduced execution saves power by eliminating unnecessary operations within the CPU and memory. When the Doze Enable bit is set (DOZEN = 1), the CPU executes only one instruction cycle out of every N cycles as defined by the DOZE bits. For example, if DOZE = 001, the instruction cycle ratio is 1:4. The CPU and memory execute for one instruction cycle and then lay idle for three instruction cycles. During the unused cycles, the peripherals continue to operate at the system clock speed. Related Links CPUDOZE 11.1.1 Doze Operation The Doze operation is illustrated in Figure 11-1. For this example: * Doze enabled (DOZEN = 1) * DOZE = 001 (1:4) ratio * Recover-on-Interrupt enabled (ROI = 1) As with normal operation, the PFM fetches for the next instruction cycle. The Q-clocks to the peripherals continue throughout. Figure 11-1. DOZE MODE OPERATION EXAMPLE (DOZE<2:0> = 001, 1:4) Rev. 3000089A 4/11/2017 11.1.2 Interrupts During Doze System behavior if an interrupt occurs during DOZE can be configured using the Recover-on-Interrupt (ROI) bit and the Doze-on-Exit (DOE) bit. Refer to the table below for details about system behavior in all cases for a transition from Main to ISR back to Main. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 147 PIC16(L)F18424/44 Power-Saving Operation Modes Table 11-1. Interrupts During DOZE DOZEN ROI Code Flow Main ISR(1) 0 Normal Operation Normal operation and DOE = DOZEN (in hardware) DOZEN = 0 (unchanged) 0 1 Normal Operation 1 0 DOZE operation 0 1 1 DOZE operation Return to Main Normal operation and DOE = DOZEN (in hardware) DOZEN = 0 If DOE = 1 when return (unchanged) from interrupt: DOZE operation and DOZEN = DOZE operation and 1 (in hardware) DOE = DOZEN (in If DOE = 0 when return from interrupt: Normal operation and DOZEN = 0 (in hardware) hardware) DOZEN = 1 (unchanged) Normal operation and DOE = DOZEN (in hardware) DOZEN = 0 (unchanged) Note: 1. User software can change DOE bit in the ISR. 11.2 Sleep Mode Sleep mode is entered by executing the SLEEP instruction, while the Idle Enable (IDLEN) bit of the CPUDOZE register is clear (IDLEN = 0). Upon entering Sleep mode, the following conditions exist: 1. 2. 3. 4. 5. 6. 7. WDT will be cleared but keeps running if enabled for operation during Sleep The PD bit of the STATUS register is cleared The TO bit of the STATUS register is set The CPU clock is disabled LFINTOSC, SOSC, HFINTOSC and ADCRC are unaffected and peripherals using them may continue operation in Sleep. I/O ports maintain the status they had before Sleep was executed (driving high, low, or highimpedance) Resets other than WDT are not affected by Sleep mode Refer to individual chapters for more details on peripheral operation during Sleep. To minimize current consumption, the following conditions should be considered: * * * I/O pins should not be floating External circuitry sinking current from I/O pins Internal circuitry sourcing current from I/O pins (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 148 PIC16(L)F18424/44 Power-Saving Operation Modes * * Current draw from pins with internal weak pull-ups Modules using any oscillator I/O pins that are high-impedance inputs should be pulled to VDD or VSS externally to avoid switching currents caused by floating inputs. Examples of internal circuitry that might be sourcing current include modules such as the DAC and FVR modules. Related Links Low-Power Sleep Mode STATUS (FVR) Fixed Voltage Reference (DAC) 5-Bit Digital-to-Analog Converter Module 11.2.1 Wake-up from Sleep The device can wake-up from Sleep through one of the following events: 1. 2. 3. 4. 5. 6. External Reset input on MCLR pin, if enabled. BOR Reset, if enabled. POR Reset. Windowed Watchdog Timer, if enabled. Any external interrupt. Interrupts by peripherals capable of running during Sleep (see individual peripheral for more information). The first three events will cause a device Reset. The last three events are considered a continuation of program execution. To determine whether a device Reset or wake-up event occurred, refer to the "Memory Execution Violation" section. When the SLEEP instruction is being executed, the next instruction (PC + 1) is prefetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be enabled. Wake-up will occur regardless of the state of the GIE bit. If the GIE bit is disabled, the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is enabled, the device executes the instruction after the SLEEP instruction, the device will then call the Interrupt Service Routine. In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction. The WDT is cleared when the device wakes-up from Sleep, regardless of the source of wake-up. Related Links Memory Execution Violation 11.2.2 Wake-up Using Interrupts When global interrupts are disabled (GIE cleared) and any interrupt source, with the exception of the clock switch interrupt, has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: * If the interrupt occurs before the execution of a SLEEP instruction - SLEEP instruction will execute as a NOP - - WDT and WDT prescaler will not be cleared TO bit of the STATUS register will not be set (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 149 PIC16(L)F18424/44 Power-Saving Operation Modes * - PD bit of the STATUS register will not be cleared If the interrupt occurs during or after the execution of a SLEEP instruction - SLEEP instruction will be completely executed - - - - Device will immediately wake-up from Sleep WDT and WDT prescaler will be cleared TO bit of the STATUS register will be set PD bit of the STATUS register will be cleared Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. Figure 11-2. WAKE-UP FROM SLEEP THROUGH INTERRUPT Rev. 3000090A 4/12/2017 CLKIN(1) TOST(3) CLKOUT(2) Interrupt Latency (4) Interrupt flag GIE bit (INTCON reg.) Instruction Flow PC Instruction Fetched Instruction Executed Processor in Sleep PC Inst(PC) = Sleep Inst(PC - 1) PC + 1 PC + 2 PC + 2 PC + 2 Inst(PC + 1) Inst(PC + 2) Sleep Inst(PC + 1) Forced NOP 0004h 0005h Inst(0004h) Inst(0005h) Forced NOP Inst(0004h) Note: 1. External clock. High, Medium, Low mode assumed. 2. CLKOUT is shown here for timing reference. 3. TOST = 1024 TOSC. This delay does not apply to EC and INTOSC Oscillator modes. 4. GIE = 1 assumed. In this case after wake-up, the processor calls the ISR at 0004h. If GIE = 0, execution will continue in-line. 11.2.3 Low-Power Sleep Mode The PIC16(L)F18424/44 devices contain an internal Low Dropout (LDO) voltage regulator, which allows the device I/O pins to operate at voltages up to 5.5V while the internal device logic operates at a lower voltage. The LDO and its associated reference circuitry must remain active when the device is in Sleep mode. The PIC16(L)F18424/44 devices allow the user to optimize the operating current in Sleep, depending on the application requirements. Low-Power Sleep mode can be selected by setting the VREGPM bit of the VREGCON register. Depending on the configuration of these bits, the LDO and reference circuitry are placed in a low-power state when the device is in Sleep. 11.2.3.1 Sleep Current vs. Wake-up Time In the default operating mode, the LDO and reference circuitry remain in the normal configuration while in Sleep. The device is able to exit Sleep mode quickly since all circuits remain active. In Low-Power Sleep mode, when waking-up from Sleep, an extra delay time is required for these circuits to return to the normal configuration and stabilize. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 150 PIC16(L)F18424/44 Power-Saving Operation Modes The Low-Power Sleep mode is beneficial for applications that stay in Sleep mode for long periods of time. The Normal mode is beneficial for applications that need to wake from Sleep quickly and frequently. 11.2.3.2 Peripheral Usage in Sleep Some peripherals that can operate in Sleep mode will not operate properly with the Low-Power Sleep mode selected. The Low-Power Sleep mode is intended for use with these peripherals: * * * * Brown-out Reset (BOR) Windowed Watchdog Timer (WWDT) External interrupt pin/Interrupt-On-Change pins Timer1 (with external clock source) It is the responsibility of the end user to determine what is acceptable for their application when setting the VREGPM settings in order to ensure operation in Sleep. Important: The LF devices do not have a configurable Low-Power Sleep mode. LFs are unregulated devices and are always in the lowest power state when in Sleep, with no wake-up time penalty. These devices have a lower maximum VDD and I/O voltage than the F devices. 11.3 Idle Mode When the Idle Enable (IDLEN) bit is clear (IDLEN = 0), the SLEEP instruction will put the device into full Sleep mode. When IDLEN is set (IDLEN = 1), the SLEEP instruction will put the device into IDLE mode. In IDLE mode, the CPU and memory operations are halted, but the peripheral clocks continue to run. This mode is similar to DOZE mode, except that in IDLE both the CPU and program memory are shut off. Important: Peripherals using FOSC will continue running while in Idle (but not in Sleep). Peripherals using HFINTOSC:LFINTOSC will continue running in both Idle and Sleep. Important: If CLKOUTEN is enabled (CLKOUTEN = 0, Configuration Word 1), the output will continue operating while in Idle. 11.3.1 Idle and Interrupts IDLE mode ends when an interrupt occurs (even if GIE = 0), but IDLEN is not changed. The device can re-enter IDLE by executing the SLEEP instruction. If Recover-on-Interrupt is enabled (ROI = 1), the interrupt that brings the device out of Idle also restores full-speed CPU execution when doze is also enabled. 11.3.2 Idle and WWDT When in Idle, the WWDT Reset is blocked and will instead wake the device. The WWDT wake-up is not an interrupt, therefore ROI does not apply. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 151 PIC16(L)F18424/44 Power-Saving Operation Modes Important: The WWDT can bring the device out of Idle, in the same way it brings the device out of Sleep. The DOZEN bit is not affected. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 152 PIC16(L)F18424/44 Power-Saving Operation Modes 11.4 Register Summary - Power Savings Control Offset Name Bit Pos. 0x0812 VREGCON 7:0 VREGPM 0x0813 ... Reserved 0x088B 0x088C 11.5 CPUDOZE 7:0 IDLEN DOZEN ROI DOE DOZE[2:0] Register Definitions: Power Savings Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 153 PIC16(L)F18424/44 Power-Saving Operation Modes 11.5.1 VREGCON Name: Offset: VREGCON 0x812 Voltage Regulator Control Register Bit 7 6 5 4 3 2 1 0 VREGPM Access R/W Reset 0 Bit 1 - VREGPM Voltage Regulator Power Mode Selection bit This register is available only for F devices. Value 1 0 Description Low-Power Sleep mode enabled in Sleep. Draws lowest current in Sleep, slower wake-up Normal Power mode enabled in Sleep. Draws higher current in Sleep, faster wake-up (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 154 PIC16(L)F18424/44 Power-Saving Operation Modes 11.5.2 CPUDOZE Name: Offset: CPUDOZE 0x88C Doze and Idle Register Bit Access Reset 7 6 5 4 IDLEN DOZEN ROI DOE 3 2 1 0 R/W R/W/HC/HS R/W R/W/HC/HS R/W R/W R/W 0 0 0 0 0 0 0 DOZE[2:0] Bit 7 - IDLEN Idle Enable bit Value 1 0 Description A SLEEP instruction places device into IDLE mode A SLEEP instruction places the device into Sleep mode Bit 6 - DOZEN Doze Enable bit(1) Value 1 0 Description Places devices into DOZE setting Places devices into Normal mode Bit 5 - ROI Recover-on-Interrupt bit(1) Value 1 0 Description Entering the Interrupt Service Routine (ISR) makes DOZEN = 0 Entering the Interrupt Service Routine (ISR) does not change DOZEN Bit 4 - DOE Doze-on-Exit bit(1) Value 1 0 Description Executing the ISR makes DOZEN = 1 Exiting the ISR does not change DOZEN Bits 2:0 - DOZE[2:0] Ratio of CPU Instruction Cycles to Peripheral Instruction Cycles Value 111 110 101 100 011 010 001 000 Description 1:256 1:128 1:64 1:32 1:16 1:8 1:4 1:2 Note: 1. See the link below for more details. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 155 PIC16(L)F18424/44 Power-Saving Operation Modes Related Links Interrupts During Doze (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 156 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12. (WWDT) Windowed Watchdog Timer The Watchdog Timer (WDT) is a system timer that generates a Reset if the firmware does not issue a CLRWDT instruction within the time-out period. The Watchdog Timer is typically used to recover the system from unexpected events. The Windowed Watchdog Timer (WWDT) differs in that CLRWDT instructions are only accepted when they are performed within a specific window during the time-out period. The WWDT has the following features: * * * * * Selectable clock source Multiple operating modes - WWDT is always on - WWDT is off when in Sleep - WWDT is controlled by software - WWDT is always off Configurable time-out period is from 1 ms to 256s (nominal) Configurable window size from 12.5% to 100% of the time-out period Multiple Reset conditions (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 157 Filename: Title: Last Edit: First Used: Notes: 10-000162A.vsd Windowed Watchdog Timer Timer Block Diagram 1/2/2014 PIC16(L)F1613 (LECQ) PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer Figure 12-1. Windowed Watchdog Timer Block Diagram Rev. 10-000 162A 1/2/201 4 WWDT Armed WDT Window Violation Window Closed Window Sizes CLRWDT Comparator WINDOW RESET Reserved 111 Reserved 110 Reserved 101 Reserved 100 Reserved 011 SOSC 010 MFINTOSC/16 001 LFINTOSC 000 R 18-bit Prescale Counter E CS PS R 5-bit WDT Counter Overflow Latch WDT Time-out WDTE<1:0> = 01 SEN WDTE<1:0> = 11 WDTE<1:0> = 10 Sleep 12.1 Independent Clock Source The WWDT can derive its time base from either the 31 kHz LFINTOSC or 31.25 kHz MFINTOSC internal oscillators, depending on the value of WDTE Configuration bits. If WDTE = 'b1x, then the clock source will be enabled depending on the WDTCCS Configuration bits. If WDTE = 'b01, the SEN bit should be set by software to enable WWDT, and the clock source is enabled by the WDTCS bits. Time intervals in this chapter are based on a minimum nominal interval of 1 ms. See "Electrical Specifications" for LFINTOSC and MFINTOSC tolerances. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 158 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer Related Links CONFIG3 Internal Oscillator Parameters(1) 12.2 WWDT Operating Modes The Windowed Watchdog Timer module has four operating modes controlled by the WDTE bits in Configuration Words. See Table 12-1. 12.2.1 WWDT Is Always On When the WDTE bits of Configuration Words are set to `11', the WWDT is always on. WWDT protection is active during Sleep. 12.2.2 WWDT Is Off in Sleep When the WDTE bits of Configuration Words are set to `10', the WWDT is on, except in Sleep. WWDT protection is not active during Sleep. 12.2.3 WWDT Controlled by Software When the WDTE bits of Configuration Words are set to `01', the WWDT is controlled by the SEN bit. WWDT protection is unchanged by Sleep. See the following table for more details. Table 12-1. WWDT Operating Modes WDTE<1:0> SEN Device Mode WWDT Mode 11 X X Active 10 X Awake Active Sleep Disabled 1 X Active 0 X Disabled X X Disabled 01 00 12.3 Time-out Period If the WDTCPS Configuration bits default to 0'b11111, then the WDTPS bits set the time-out period from 1 ms to 256 seconds (nominal). If any value other than the default value is assigned to WDTCPS Configuration bits, then the timer period will be based on the WDTCPS bits in the CONFIG3 register. After a Reset, the default time-out period is 2s. Related Links CONFIG3 12.4 Watchdog Window The Windowed Watchdog Timer has an optional Windowed mode that is controlled by the WDTCWS Configuration bits and WINDOW bits. In the Windowed mode, the CLRWDT instruction must occur within (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 159 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer the allowed window of the WDT period. Any CLRWDT instruction that occurs outside of this window will trigger a window violation and will cause a WWDT Reset, similar to a WWDT time out. See Figure 12-2 for an example. The window size is controlled by the WINDOW Configuration bits, or the WINDOW bits, if WDTCWS = 111. The five Most Significant bits of the WDTTMR register are used to determine whether the window is open, as defined by the WINDOW bits. In the event of a window violation, a Reset will be generated and the WDTWV bit of the PCON0 register will be cleared. This bit is set by a POR or can be set in firmware. Related Links PCON0 12.5 Clearing the WWDT The WWDT is cleared when any of the following conditions occur: 12.5.1 * * Any Reset Valid CLRWDT instruction is executed * * * * * Device enters Sleep Exit Sleep by Interrupt WWDT is disabled Oscillator Start-up Timer (OST) is running Any write to the WDTCON0 or WDTCON1 registers CLRWDT Considerations (Windowed Mode) When in Windowed mode, the WWDT must be armed before a CLRWDT instruction will clear the timer. This is performed by reading the WDTCON0 register. Executing a CLRWDT instruction without performing such an arming action will trigger a window violation regardless of whether the window is open or not. See Table 12-2 for more information. 12.6 Operation During Sleep When the device enters Sleep, the WWDT is cleared. If the WWDT is enabled during Sleep, the WWDT resumes counting. When the device exits Sleep, the WWDT is cleared again. The WWDT remains clear until the Oscillator Start-up Timer (OST) completes, if enabled. When a WWDT time-out occurs while the device is in Sleep, no Reset is generated. Instead, the device wakes up and resumes operation. The TO and PD bits in the STATUS register are changed to indicate the event. The RWDT bit in the PCON0 register can also be used. Table 12-2. WWDT Clearing Conditions Conditions WWDT WDTE = 00 Cleared WDTE = 01 and SEN = 0 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 160 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer Conditions WWDT WDTE = 10 and enter Sleep CLRWDT Command Oscillator Fail Detected 10-000163A.vsd ExitFilename: Sleep + System Clock = SOSC, EXTRC, INTOSC, EXTCLK Title: WDT WINDOW PERIOD AND DELAY Edit: + System 8/15/2016 ExitLast Sleep Clock = XT, HS, LP First Used: Notes:INTOSC Change Cleared until the end of OST PIC16(L)F1613 (LECQ) divider (IRCF bits) Unaffected Figure 12-2. Window Period and Delay Rev. 10-000163A 8/15/2016 CLRWDT Instruction (or other WDT Reset) Window Period Window Closed Window Open Window Delay (window violation can occur) Time-out Event Related Links Oscillator Start-up Timer (OST) STATUS PCON0 Memory Organization (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 161 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12.7 Register Summary - WDT Control Offset Name Bit Pos. 0x080C WDTCON0 7:0 0x080D WDTCON1 7:0 0x080E WDTPSL 7:0 0x080F WDTPSH 7:0 0x0810 WDTTMR 7:0 12.8 WDTPS[4:0] SEN WDTCS[2:0] WINDOW[2:0] PSCNTL[7:0] PSCNTH[7:0] WDTTMR[4:0] STATE PSCNT[1:0] Register Definitions: Windowed Watchdog Timer Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 162 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12.8.1 WDTCON0 Name: Offset: WDTCON0 0x80C Watchdog Timer Control Register 0 Bit 7 6 5 4 3 2 1 WDTPS[4:0] Access Reset 0 SEN R/W R/W R/W R/W R/W R/W q q q q q 0 Bits 5:1 - WDTPS[4:0] Watchdog Timer Prescale Select bits(1) Bit Value = Prescale Rate Value 11111 to 10011 10010 10001 10000 01111 01110 01101 01100 01011 01010 01001 01000 00111 00110 00101 00100 00011 00010 00001 00000 Description Reserved. Results in minimum interval (1 ms) 1:8388608 (223) (Interval 256s nominal) 1:4194304 (222) (Interval 128s nominal) 1:2097152 (221) (Interval 64s nominal) 1:1048576 (220) (Interval 32s nominal) 1:524288 (219) (Interval 16s nominal) 1:262144 (218) (Interval 8s nominal) 1:131072 (217) (Interval 4s nominal) 1:65536 (Interval 2s nominal) (Reset value) 1:32768 (Interval 1s nominal) 1:16384 (Interval 512 ms nominal) 1:8192 (Interval 256 ms nominal) 1:4096 (Interval 128 ms nominal) 1:2048 (Interval 64 ms nominal) 1:1024 (Interval 32 ms nominal) 1:512 (Interval 16 ms nominal) 1:256 (Interval 8 ms nominal) 1:128 (Interval 4 ms nominal) 1:64 (Interval 2 ms nominal) 1:32 (Interval 1 ms nominal) Bit 0 - SEN Software Enable/Disable for Watchdog Timer bit Value -- 1 0 -- Condition If WDTE = 1x If WDTE = 01 If WDTE = 01 If WDTE = 00 Description This bit is ignored WDT is turned on WDT is turned off This bit is ignored Note: 1. Times are approximate. WDT time is based on 31 kHz LFINTOSC. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 163 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 2. 3. When WDTCPS in CONFIG3 = 11111, the Reset value (q) of WDTPS is `01011'. Otherwise, the Reset value of WDTPS is equal to WDTCPS in CONFIG3. When WDTCPS in CONFIG3L 11111, these bits are read-only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 164 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12.8.2 WDTCON1 Name: Offset: WDTCON1 0x80D Watchdog Timer Control Register 1 Bit 7 6 5 4 3 2 WDTCS[2:0] Access Reset 1 0 WINDOW[2:0] R/W R/W R/W R/W R/W R/W q q q q q q Bits 6:4 - WDTCS[2:0] Watchdog Timer Clock Select bits Value 111 to 010 001 000 Description Reserved MFINTOSC 31.25 kHz LFINTOSC 31 kHz Bits 2:0 - WINDOW[2:0] Watchdog Timer Window Select bits WINDOW Window delay Percent of time Window opening Percent of time 111 N/A 100 110 12.5 87.5 101 25 75 100 37.5 62.5 011 50 50 010 62.5 37.5 001 75 25 000 87.5 12.5 Note: 1. If WDTCCS in CONFIG3 = 111, the Reset value of WDTCS is `000'. 2. 3. The Reset value (q) of WINDOW is determined by the value of WDTCWS in the CONFIG3 register. If WDTCCS in CONFIG3 111, these bits are read-only. 4. If WDTCWS in CONFIG3 111, these bits are read-only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 165 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12.8.3 WDTPSH Name: Offset: WDTPSH 0x80F WWDT Prescale Select High Register (Read-Only) Bit 7 6 5 4 3 2 1 0 PSCNTH[7:0] Access Reset RO RO RO RO RO RO RO RO 0 0 0 0 0 0 0 0 Bits 7:0 - PSCNTH[7:0] Prescale Select High Byte bits(1) Note: 1. The 18-bit WDT prescale value, PSCNT<17:0> includes the WDTPSL, WDTPSH and the lower bits of the WDTTMR registers. PSCNT<17:0> is intended for debug operations and should be read during normal operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 166 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12.8.4 WDTPSL Name: Offset: WDTPSL 0x80E WWDT Prescale Select Low Register (Read-Only) Bit 7 6 5 4 3 2 1 0 PSCNTL[7:0] Access Reset RO RO RO RO RO RO RO RO 0 0 0 0 0 0 0 0 Bits 7:0 - PSCNTL[7:0] Prescale Select Low Byte bits(1) Note: 1. The 18-bit WDT prescale value, PSCNT<17:0> includes the WDTPSL, WDTPSH and the lower bits of the WDTTMR registers. PSCNT<17:0> is intended for debug operations and should be read during normal operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 167 PIC16(L)F18424/44 (WWDT) Windowed Watchdog Timer 12.8.5 WDTTMR Name: Offset: WDTTMR 0x810 WDT Timer Register (Read-Only) Bit 7 6 5 4 3 2 WDTTMR[4:0] Access Reset 1 STATE 0 PSCNT[1:0] RO RO RO RO RO RO RO RO 0 0 0 0 0 0 0 0 Bits 7:3 - WDTTMR[4:0] Watchdog Window Value bits WINDOW WDT Window State Open Percent Closed Open 111 N/A 00000-11111 100 110 00000-00011 00100-11111 87.5 101 00000-00111 01000-11111 75 100 00000-01011 01100-11111 62.5 011 00000-01111 10000-11111 50 010 00000-10011 10100-11111 37.5 001 00000-10111 11000-11111 25 000 00000-11011 11100-11111 12.5 Bit 2 - STATE WDT Armed Status bit Value 1 0 Description WDT is armed WDT is not armed Bits 1:0 - PSCNT[1:0] Prescale Select Upper Byte bits(1) Note: 1. The 18-bit WDT prescale value, PSCNT<17:0> includes the WDTPSL, WDTPSH and the lower bits of the WDTTMR registers. PSCNT<17:0> is intended for debug operations and should be read during normal operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 168 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13. (NVM) Nonvolatile Memory Control Nonvolatile Memory (NVM) is separated into two types: Program Flash Memory (PFM) and Data EEPROM Memory. NVM is accessible by using both the FSR and INDF registers, or through the NVMREG register interface. The write time is controlled by an on-chip timer. The write/erase voltages are generated by an on-chip charge pump rated to operate over the operating voltage range of the device. NVM can be protected in two ways, by either code protection or write protection. Code protection (CP and CPD bits in the Configuration Words) disables access, reading and writing to both PFM and Data EEPROM Memory via external device programmers. Code protection does not affect the self-write and erase functionality. Code protection can only be reset by a device programmer performing a Bulk Erase to the device, clearing all nonvolatile memory, Configuration bits and User IDs. Write protection prohibits self-write and erase to a portion or all of the NVM, as defined by the WRTSAF, WRTD, WRTC, WRTB, and WRTAPP bits of Configuration Word 4. Write protection does not affect a device programmer's ability to read, write, or erase the device. Related Links CONFIG4 CONFIG5 13.1 Program Flash Memory Program Flash Memory consists of an array of 14-bit words as user memory, with additional words for User ID information, Configuration words, and interrupt vectors. Program memory provides storage locations for: * User program instructions * User defined data Program memory data can be read and/or written to through: * CPU instruction fetch (read-only) * FSR/INDF indirect access (read-only) * NVMREG access TM * In-Circuit Serial Programming (ICSP ) Read operations return a single word of memory. When write and erase operations are done on a row basis, the row size is defined. Program memory will erase to a logic `1' and program to a logic `0'. It is important to understand the program memory structure for erase and programming operations. Program memory is arranged in rows. A row consists of 32 14-bit program memory words. A row is the minimum size that can be erased by user software. All or a portion of a row can be programmed. Data to be written into the program memory row is written to 14-bit wide data write latches. These latches are not directly accessible, but may be loaded via sequential writes to the NVMDATH:NVMDATL register pair. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 169 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control Important: To modify only a portion of a previously programmed row, the contents of the entire row must be read. Then, the new data and retained data can be written into the write latches to reprogram the row of program memory. However, any unprogrammed locations can be written without first erasing the row. In this case, it is not necessary to save and rewrite the other previously programmed locations Related Links FSR and INDF Access NVMREG Access 13.1.1 Program Memory Voltages The program memory is readable and writable during normal operation over the full VDD range. 13.1.1.1 Programming Externally The program memory cell and control logic support write and Bulk Erase operations down to the minimum device operating voltage. Special BOR operation is enabled during Bulk Erase. Related Links BOR is Always Off 13.1.1.2 Self-programming The program memory cell and control logic will support write and row erase operations across the entire VDD range. Bulk Erase is not available when self-programming. 13.2 Data EEPROM Data EEPROM consists of 256 bytes of user data memory. The EEPROM provides storage locations for 8-bit user defined data. EEPROM can be read and/or written through: * FSR/INDF indirect access * NVMREG access * External device programmer Unlike Program Flash Memory, which must be written to by row, EEPROM can be written to byte by byte. Related Links FSR and INDF Access NVMREG Access 13.3 FSR and INDF Access The FSR and INDF registers allow indirect access to the program memory or EEPROM. Related Links FSR0 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 170 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.3.1 FSR Read With the intended address loaded into an FSR register a MOVIW instruction or read of INDF will read data from the program memory or EEPROM. Reading from NVM requires one instruction cycle. The CPU operation is suspended during the read, and resumes immediately after. Read operations return a single byte of memory. 13.3.2 FSR Write Writing/erasing the NVM through the FSR registers (ex. MOVWI instruction) is not supported in the PIC16(L)F184XX devices. 13.4 NVMREG Access The NVMREG interface allows read/write access to all the locations accessible by FSRs, and also read/ write access to the User ID locations and EEPROM, and read-only access to the device identification, revision, and Configuration data. Writing or erasing of NVM via the NVMREG interface is prevented when the device is write-protected. 13.4.1 NVMREG Read Operation To read a NVM location using the NVMREG interface, the user must: 1. Clear the NVMREGS bit of the NVMCON1 register if the user intends to access program memory locations, or set NMVREGS if the user intends to access User ID, EEPROM, or Configuration locations. 2. Write the desired address into the NVMADRH:NVMADRL register pair. 3. Set the RD bit of the NVMCON1 register to initiate the read. Once the read control bit is set, the CPU operation is suspended during the read, and resumes immediately after. The data is available in the very next cycle, in the NVMDATH:NVMDATL register pair; therefore, it can be read as two bytes in the following instructions. NVMDATH:NVMDATL register pair will hold this value until another read or until it is written to by the user. Upon completion, the RD bit is cleared by hardware. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 171 Filename: Title: Last Edit: First Used: Note: 10-000046D.vsd FLASH PROGRAM MEMORY READ FLOWCHART 8/15/2016 PIC16(L)F15354/55 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control Figure 13-1. Flash Program Memory Read Flowchart Rev. 10-000046E 5/17/2017 Start Read Operation Select Memory: Program Memory, DIA, DCI, Config Words, User ID (NVMREGS) Select Word Address (NVMADRH:NVMADRL) Data read now in NVMDATH:NVMDATL End Read Operation Program Memory read * This code block will read 1 word of program * memory at the memory address: PROG_ADDR_HI : PROG_ADDR_LO * data will be returned in the variables; * PROG_DATA_HI, PROG_DATA_LO BANKSEL MOVLW MOVWF MOVLW MOVWF NVMADRL PROG_ADDR_LO NVMADRL PROG_ADDR_HI NVMADRH ; Select Bank for NVMCON registers ; ; Store LSB of address ; ; Store MSB of address BCF BSF NVMCON1,NVMREGS NVMCON1,RD ; Do not select Configuration Space ; Initiate read MOVF MOVWF MOVF MOVWF NVMDATL,W PROG_DATA_LO NVMDATH,W PROG_DATA_HI ; ; ; ; Get LSB of word Store in user location Get MSB of word Store in user location Related Links NVMADR NVMDAT NVMCON1 13.4.2 NVM Unlock Sequence The unlock sequence is a mechanism that protects the NVM from unintended self-write programming or erasing. The sequence must be executed and completed without interruption to successfully complete any of the following operations: * Program Flash Memory Row Erase * Load of Program Flash Memory write latches (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 172 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control * * * Write of Program Flash Memory write latches to program memory Write of Program Flash Memory write latches to User IDs Write to EEPROM The unlock sequence consists of the following steps and must be completed in order: * Write 55h to NVMCON2 * Write AAh to NMVCON2 * Set the WR bit of NVMCON1 Once the WR bit is set, the processor will stall internal operations until the operation is complete and then resume with the next instruction. Important: The two NOP instructions after setting the WR bit that were required in previous devices are not required for PIC16(L)F184XX devices. See figure below. Filename: 10-000047B.vsd Title: FLASH PROGRAM MEMORY UNLOCK SEQUENCE FLOWCHART Last Edit: 8/24/2015 First Used: PIC15F1508/9 mustNote: not be interrupted, global interrupts should be disabled prior to the Since the unlock sequence unlock sequence and re-enabled after the unlock sequence is completed. Figure 13-2. NVM Unlock Sequence Flowchart Rev. 10-000047B 8/24/2015 Start Unlock Sequence Write 0x55 to NVMCON2 Write 0xAA to NVMCON2 Initiate Write or Erase operation (WR = 1) End Unlock Sequence NVM Unlock Sequence BCF BANKSEL BSF MOVLW MOVWF MOVLW MOVWF INTCON, GIE NVMCON1 NVMCON1, WREN 55h NVMCON2 AAh NVMCON2 (c) 2018 Microchip Technology Inc. ; ; ; ; ; ; ; Recommended so sequence is not interrupted Enable write/erase Load 55h Step 1: Load 55h into NVMCON2 Step 2: Load W with AAh Step 3: Load AAH into NVMCON2 Datasheet Preliminary DS40002000A-page 173 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control BSF BSF NVMCON1, WR INTCON, GIE ; Step 4: Set WR bit to begin write/erase ; Re-enable interrupts Note: 1. Sequence begins when NVMCON2 is written; steps 1-4 must occur in the cycleaccurate order shown. 2. Opcodes shown are illustrative; any instruction that has the indicated effect may be used. 13.4.3 NVMREG Write to EEPROM Writing to the EEPROM is accomplished by the following steps: 1. Set the NVMREGS and WREN bits of the NVMCON1 register. 2. Write the desired address (address +7000h) into the NVMADRH:NVMADRL register pair. 3. Perform the unlock sequence as described in the "NVM Unlock Sequence" section. A single EEPROM byte is written with NVMDATA. The operation includes an implicit erase cycle for that byte (it is not necessary to set the FREE bit), and requires many instruction cycles to finish. CPU execution continues in parallel and, when complete, WR is cleared by hardware, NVMIF is set, and an interrupt will occur if NVMIE is also set. Software must poll the WR bit to determine when writing is complete, or wait for the interrupt to occur. WREN will remain unchanged. Once the EEPROM write operation begins, clearing the WR bit will have no effect; the operation will run to completion. Related Links NVM Unlock Sequence NVMREG Erase of Program Memory 13.4.4 NVMREG Erase of Program Memory Before writing to program memory, the word(s) to be written must be erased or previously unwritten. Program memory can only be erased one row at a time. No automatic erase occurs upon the initiation of the write to program memory. To erase a program memory row: 1. Clear the NVMREGS bit of the NVMCON1 register to erase program memory locations, or set the NMVREGS bit to erase User ID locations. 2. Write the desired address into the NVMADRH:NVMADRL register pair. 3. Set the FREE and WREN bits of the NVMCON1 register. 4. Perform the unlock sequence as described in the "NVM Unlock Sequence" section. If the program memory address is write-protected, the WR bit will be cleared and the erase operation will not take place. While erasing program memory, CPU operation is suspended, and resumes when the operation is complete. Upon completion, the NVMIF is set, and an interrupt will occur if the NVMIE bit is also set. Write latch data is not affected by erase operations, and WREN will remain unchanged. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 174 Filename: Title: Last Edit: First Used: Note: 10-000048B.vsd FLASH MEMORY PROGRAM MEMORY ERASE FLOWCHART 8/24/2015 PIC16F18855 See Figure 10-2 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control Figure 13-3. NVM Erase Flowchart Rev. 10-000048B 8/24/2015 Start Erase Operation Select Memory: PFM, Config Words, User ID (NVMREGS) Select Word Address (NVMADRH:NVMADRL) Select Erase Operation (FREE=1) Enable Write/Erase Operation (WREN=1) Disable Interrupts (GIE=0) Unlock Sequence (See Note 1) CPU stalls while Erase operation completes (2 ms typical) Disable Write/Erase Operation (WREN = 0) Re-enable Interrupts (GIE = 1) End Erase Operation Note: See previous figure. Erasing One Row of Program Flash Memory ; This sample row erase routine assumes the following: ; 1.A valid address within the erase row is loaded in variables ADDRH:ADDRL ; 2.ADDRH and ADDRL are located in common RAM (locations 0x70 - 0x7F) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 175 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control BANKSEL MOVF MOVWF MOVF MOVWF BCF BSF BSF BCF NVMADRL ADDRL,W NVMADRL ADDRH,W NVMADRH NVMCON1,NVMREGS NVMCON1,FREE NVMCON1,WREN INTCON,GIE ; Load lower 8 bits of erase address boundary ; ; ; ; ; Load upper 6 bits of erase address boundary Choose PFM memory area Specify an erase operation Enable writes Disable interrupts during unlock sequence ; ---------------------REQUIRED UNLOCK SEQUENCE:-------------------MOVLW MOVWF MOVLW MOVWF BSF 55h NVMCON2 AAh NVMCON2 NVMCON1,WR ; ; ; ; ; Load 55h to get ready for unlock sequence First step is to load 55h into NVMCON2 Second step is to load AAh into W Third step is to load AAh into NVMCON2 Final step is to set WR bit ; -----------------------------------------------------------------BSF BCF INTCON,GIE NVMCON1,WREN ; Re-enable interrupts, erase is complete ; Disable writes Table 13-1. NVM Organization and Access Information Master Values Memory Function Memory Type RESET VECTOR NVMREG Access FSR Access Program NVMREGS FSR ICSP Allowed FSR Counter bit NVMADR<14:0> Programming Address Operations Address (PC) (NVMCON1) Access 0000h 0000h USER MEMORY Program Flash INT Memory VECTOR 0001h 0001h 0003h 0003h 0004h 0004h USER MEMORY 0005h 0005h 7FFFh(1) 7FFFh(1) Program Flash Memory 8000h USER ID Reserved -- 0 0 0 0 0000h 8000h 0001h 8001h 0003h 0004h READ/ WRITE 8005h 7FFFh(1) FFFFh 0000h 8003h 0003h READ -- 0004h -- 8005h -- 1 8006h 1 0006h 8007h 1 0007h 8008h 1 0008h 8009h 1 0009h 800Ah 1 000Ah CONFIG5 800Bh 1 000Bh DIA and DCI 8100h 1 0100h 82FFh 1 02FFh DEVICE ID HC CONFIG1 NO PC ACCESS CONFIG2 CONFIG3 FUSE CONFIG4 PFM USER EEPROM MEMORY F000h F0FFh (c) 2018 Microchip Technology Inc. READ ONLY 8004h 0005h 1 REV ID 8003h 1 0005h 7000h 70FFh Datasheet Preliminary READ NO ACCESS READ/ WRITE READ READ/ WRITE 7000h 70FFh READ ONLY DS40002000A-page 176 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control Note: 1. 7FFFh is the maximum Program Flash Memory address for the PIC16(L)F184XX family. Related Links Memory Organization 13.4.5 NVMREG Write to Program Memory Program memory is programmed using the following steps: 1. Load the address of the row to be programmed into NVMADRH:NVMADRL. 2. Load each write latch with data. 3. Initiate a programming operation. 4. Repeat steps 1 through 3 until all data is written. Before writing to program memory, the word(s) to be written must be erased or previously unwritten. Program memory can only be erased one row at a time. No automatic erase occurs upon the initiation of the write. Program memory can be written one or more words at a time. The maximum number of words written at one time is equal to the number of write latches. See the figure below (row writes to program memory with 32 write latches) for more details. The write latches are aligned to the Flash row address boundary defined by the upper ten bits of NVMADRH:NVMADRL, (NVMADRH<6:0>:NVMADRL<7:5>) with the lower five bits of NVMADRL, (NVMADRL<4:0>) determining the write latch being loaded. Write operations do not cross these boundaries. At the completion of a program memory write operation, the data in the write latches is reset to contain 0x7FFF. The following steps should be completed to load the write latches and program a row of program memory. These steps are divided into two parts. First, each write latch is loaded with data from the NVMDATH:NVMDATL using the unlock sequence with LWLO = 1. When the last word to be loaded into the write latch is ready, the LWLO bit is cleared and the unlock sequence executed. This initiates the programming operation, writing all the latches into Flash program memory. Important: The special unlock sequence is required to load a write latch with data or initiate a Flash programming operation. If the unlock sequence is interrupted, writing to the latches or program memory will not be initiated. 1. 2. 3. 4. 5. 6. 7. 8. Set the WREN bit of the NVMCON1 register. Clear the NVMREGS bit of the NVMCON1 register. Set the LWLO bit of the NVMCON1 register. When the LWLO bit of the NVMCON1 register is `1', the write sequence will only load the write latches and will not initiate the write to Flash program memory. Load the NVMADRH:NVMADRL register pair with the address of the location to be written. Load the NVMDATH:NVMDATL register pair with the program memory data to be written. Execute the unlock sequence. The write latch is now loaded. Increment the NVMADRH:NVMADRL register pair to point to the next location. Repeat steps 5 through 7 until all but the last write latch has been loaded. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 177 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 9. Clear the LWLO bit of the NVMCON1 register. When the LWLO bit of the NVMCON1 register is `0', the write sequence will initiate the write to Flash program memory. 10. Load the NVMDATH:NVMDATL register pair with the program memory data to be written. 11. Execute the unlock sequence. The entire program memory latch content is now written to Flash program memory. Important: The program memory write latches are reset to the blank state (0x7FFF) at the completion of every write or erase operation. As a result, it is not necessary to load all the program memory write latches. Unloaded latches will remain in the blank state. An example of the complete write sequence is shown in Writing to Program Flash Memory. The initial address is loaded into the NVMADRH:NVMADRL register pair; the data is loaded using indirect Filename: 10-000004F.vsd Title:addressing. Block Writes to PFM 32 Write Latches (RevID 8005/DevID8006/5 Config Words Last Edit: First Used: 8/15/2016 PIC16(L)F153xx Figure 13-4. NVMREG Writes to Program Flash Memory With 32 Write Latches 7 6 - r9 0 7 5 4 NVMADRH r8 r7 r6 r5 r4 r3 r2 r1 r0 c4 0 7 NVMADRL - c3 c2 c1 5 - 0 7 NVMDATH NVMDATL 6 c0 Rev. 10-000004F 8/15/2016 0 8 14 10 Program Memory Write Latches 5 14 Write Latch #0 00h 14 14 Write Latch #30 1Eh Write Latch #1 01h 14 Write Latch #31 1Fh NVMADRL<4:0> 14 NVMREGS=0 NVMADRH<6:0> NVMADRL<7:5> Row Address Decode 14 14 14 Row Addr Addr Addr Addr 000h 0000h 0001h 001Eh 001Fh 001h 0010h 0011h 003Eh 003Fh 002h 0020h 0021h 005Eh 005Fh End Addr End Addr Flash Program Memory Configuration Memory User ID, Device ID, Revision ID, Configuration Words, DIA, DCI NVMREGS = 1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 178 Filename: Title: Last Edit: First Used: Note: PIC16(L)F18424/44 10-000049C.vsd FLASH PROGRAM MEMORY WRITE FLOWCHART 8/24/2015 PIC16F18855 1. See Figure 10-2 (NVM) Nonvolatile Memory Control Figure 13-5. Program Flash Memory Flowchart Rev. 10-000049C 8/24/2015 Start Write Operation Determine number of words to be written into PFM. The number of words cannot exceed the number of words per row (word_cnt) Load the value to write TABLAT Update the word counter (word_cnt--) Select access to PFM locations using NVMREG<1:0> bits Last word to write ? Select Row Address TBLPTR Yes No Write Latches to PFM Disable Interrupts (GIE = 0) Unlock Sequence (See note 1) Disable Interrupts (GIE = 0) Select Write Operation (FREE = 0) Unlock Sequence (See note 1) Load Write Latches Only Enable Write/Erase Operation (WREN = 1) No delay when writing to PFM Latches CPU stalls while Write operation completes (2 ms typical) Re-enable Interrupts (GIE = 1) Disable Write/Erase Operation (WREN = 0) Re-enable Interrupts (GIE = 1) End Write Operation Increment Address TBLPTR++ Note: 1. See NVM Unlock Sequence Flowchart Writing to Program Flash Memory ; This write routine assumes the following: ; 1. 64 bytes of data are loaded, starting at the address in DATA_ADDR ; 2. Each word of data to be written is made up of two adjacent bytes in DATA_ADDR, ; stored in little endian format ; 3. A valid starting address (the least significant bits = 00000) is (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 179 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control loaded in ADDRH:ADDRL ; 4. ADDRH and ADDRL are located in common RAM (locations 0x70 - 0x7F) ; 5. NVM interrupts are not taken into account BANKSEL MOVF MOVWF MOVF MOVWF MOVLW MOVWF MOVLW MOVWF BCF BSF BSF NVMADRH ADDRH,W NVMADRH ADDRL,W NVMADRL LOW DATA_ADDR FSR0L HIGH DATA_ADDR FSR0H NVMCON1,NVMREGS NVMCON1,WREN NVMCON1,LWLO ; Load initial address ; Load initial data address ; Set Program Flash Memory as write location ; Enable writes ; Load only write latches LOOP MOVIW MOVWF MOVIW MOVWF FSR0++ NVMDATL FSR0++ NVMDATH MOVF XORLW ANDLW BTFSC GOTO NVMADRL,W 0x1F 0x1F STATUS,Z START_WRITE CALL INCF GOTO UNLOCK_SEQ NVMADRL,F LOOP ; If not, go load latch ; Increment address NVMCON1,LWLO UNLOCK_SEQ NVMCON1,WREN ; Latch writes complete, now write memory ; Perform required unlock sequence ; Disable writes ; Load first data byte ; Load second data byte ; ; ; ; Check if lower bits of address are 00000 and if on last of 32 addresses Last of 32 words? If so, go write latches into memory START_WRITE BCF CALL BCF UNLOCK_SEQ MOVLW BCF MOVWF MOVLW MOVWF BSF BSF interrupts return 13.4.6 55h INTCON,GIE NVMCON2 AAh NVMCON2 NVMCON1,WR INTCON,GIE ; Disable interrupts ; Begin unlock sequence ; Unlock sequence complete, re-enable Modifying Flash Program Memory When modifying existing data in a program memory row, and data within that row must be preserved, it must first be read and saved in a RAM image. Program memory is modified using the following steps: 1. Load the starting address of the row to be modified. 2. Read the existing data from the row into a RAM image. 3. Modify the RAM image to contain the new data to be written into program memory. 4. Load the starting address of the row to be rewritten. 5. Erase the program memory row. 6. Load the write latches with data from the RAM image. 7. Initiate a programming operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 180 Filename: Title: Last Edit: First Used: Note: 10-000050B.vsd FLASH PROGRAM MEMORY MODIFY FLOWCHART 8/21/2015 PIC16F18855 1. See Figure 10-1 2. See Figure 10-3 3. See Figure 10-5 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control Figure 13-6. Flash Program Memory Modify Flowchart Rev. 10-000050B 8/21/2015 Start Modify Operation Read Operation (See Note 1) An image of the entire row read must be stored in RAM Modify Image The words to be modified are changed in the RAM image Erase Operation (See Note 2) Write Operation Use RAM image (See Note 3) End Modify Operation Note: 1. See Flash Program Memory Read Flowchart. 2. See NVM Erase Flowchart. 3. See Program Flash Memory Flowchart. 13.4.7 NVMREG Access to Device Information Area, Device Configuration Area, User ID, Device ID, EEPROM, and Configuration Words NVMREGS can be used to access the following memory regions: * * * * * * Device Information Area (DIA) Device Configuration Information (DCI) User ID region Device ID and Revision ID Configuration Words EEPROM The value of NVMREGS is set to `1' in the NVMCON1 register to access these regions. The memory regions listed above would be pointed to by PC<15> = 1, but not all addresses reference valid data. Different access may exist for reads and writes. Refer to the table below. When read access is initiated on (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 181 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control an address outside the parameters listed in the following table, the NVMDATH: NVMDATL register pair is cleared, reading back `0's. Table 13-2. NVMREG Access to Device Information Area, Device Configuration Area, User ID, Device ID, EEPROM, and Configuration Words (NVMREGS = 1) Address Function Read Access Write Access 8000h-8003h User IDs Yes Yes 8005h-8006h Device ID/Revision ID Yes No 8007h-800Bh Configuration Words 1-5 Yes Yes 8100h-82FFh DIA and DCI Yes No F000h-F0FFh EEPROM Yes Yes Device ID Access ; This write routine assumes the following: ; 1. A full row of data are loaded, starting at the address in DATA_ADDR ; 2. Each word of data to be written is made up of two adjacent bytes in DATA_ADDR, ; stored in little endian format ; 3. A valid starting address (the least significant bits = 00000) is loaded in ADDRH:ADDRL ; 4. ADDRH and ADDRL are located in common RAM (locations 0x70 - 0x7F) ; 5. NVM interrupts are not taken into account BANKSEL MOVF MOVWF MOVF MOVWF MOVLW MOVWF MOVLW MOVWF BCF BSF BSF NVMADRH ADDRH,W NVMADRH ADDRL,W NVMADRL LOW DATA_ADDR FSR0L HIGH DATA_ADDR FSR0H NVMCON1,NVMREGS NVMCON1,WREN NVMCON1,LWLO ; Load initial address ; Load initial data address ; Set PFM as write location ; Enable writes ; Load only write latches LOOP MOVIW MOVWF MOVIW MOVWF CALL INCF MOVF XORLW ANDLW BTFSC GOTO FSR0++ NVMDATL FSR0++ NVMDATH UNLOCK_SEQ NVMADRL,F NVMADRL,W 0x1F 0x1F STATUS,Z START_WRITE GOTO LOOP ; Load first data byte ; Load second data byte ; If not, go load latch ; Increment address ; ; ; ; Check if lower bits of address are 00000 and if on last of 32 addresses Last of 32 words? If so, go write latches into memory START_WRITE BCF CALL BCF NVMCON1,LWLO UNLOCK_SEQ NVMCON1,LWLO ; Latch writes complete, now write memory ; Perform required unlock sequence ; Disable writes UNLOCK_SEQ MOVLW (c) 2018 Microchip Technology Inc. 55h Datasheet Preliminary DS40002000A-page 182 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control BCF MOVWF MOVLW MOVWF BSF BSF interrupts return 13.4.8 INTCON,GIE NVMCON2 AAh NVMCON2 NVMCON1,WR INTCON,GIE ; Disable interrupts ; Begin unlock sequence ; Unlock sequence complete, re-enable Write Verify Filename: 10-000051B.vsd Title: FLASH PROGRAM MEMORY VERIFY FLOWCHART Last Edit: It is considered good programming practice to 12/4/2015 verify that program memory writes agree with the intended First Used: PIC18(L)F2x/4xK40 value. Since program memory is stored as a full the11-5, stored program memory Note: 1: row Referthen to Figure Program Flash Memory Readcontents Flowchart are compared with the intended data stored in RAM after the last write is complete. Figure 13-7. Flash Program Memory Verify Flowchart Rev. 10-000051B 12/4/2015 Start Verify Operation This routine assumes that the last row of data written was from an image saved on RAM. This image will be used to verify the data currently stored in PFM Read Operation(1) NVMDAT = RAM image ? Yes No No Fail Verify Operation Last word ? Yes End Verify Operation Note: 1. See Flash Program Memory Read Flowchart. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 183 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.4.9 WRERR Bit The WRERR bit can be used to determine if a write error occurred. WRERR will be set if one of the following conditions occurs: * If WR is set while the NVMADRH:NMVADRL points to a write-protected address * A Reset occurs while a self-write operation was in progress * An unlock sequence was interrupted The WRERR bit is normally set by hardware, but can be set by the user for test purposes. Once set, WRERR must be cleared in software. Table 13-3. Actions for PFM When WR = 1 Free LWLO Actions for PFM when WR = 1 Comments * 1 x Erase the 32-word row of NVMADRH:NVMADRL location. 0 1 Copy NVMDATH:NVMDATL to the write latch corresponding to NVMADR LSBs. 0 0 Write the write-latch data to PFM row. * * If WP is enabled, WR is cleared and WRERR is set All 32 words are erased NVMDATH:NVMDATL is ignored * * Write protection is ignored No memory access occurs * If WP is enabled, WR is cleared and WRERR is set Write latches are reset to 3FFh NVMDATH:NVMDATL is ignored * * Related Links NVMREG Erase of Program Memory (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 184 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.5 Register Summary: NVM Control Offset Name 0x081A NVMADR Bit Pos. 7:0 15:8 NVMADRH[6:0] 7:0 0x081C NVMDAT 0x081E NVMCON1 7:0 0x081F NVMCON2 7:0 13.6 NVMADRL[7:0] NVMDATL[7:0] 15:8 NVMDATH[5:0] NVMREGS LWLO FREE WRERR WREN WR RD NVMCON2[7:0] Register Definitions: Nonvolatile Memory (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 185 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.6.1 NVMADR Name: Offset: NVMADR 0x81A Nonvolatile Memory Address Register Bit 15 14 13 12 11 10 9 8 NVMADRH[6:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 NVMADRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 14:8 - NVMADRH[6:0] NVM Most Significant Address bits Specifies the Most Significant bits for program memory address. Bits 7:0 - NVMADRL[7:0] NVM Least Significant Address bits Specifies the Least Significant bits for program memory address. Note: 1. Bit <15> is undefined while WR = 1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 186 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.6.2 NVMDAT Name: Offset: NVMDAT 0x81C Nonvolatile Memory Data Register Bit 15 14 13 12 11 10 9 8 NVMDATH[5:0] Access Reset Bit 7 6 R/W R/W R/W R/W R/W R/W x x x x x x 5 4 3 2 1 0 NVMDATL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 13:8 - NVMDATH[5:0] Read/write value for Most Significant bits of program memory Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Bits 7:0 - NVMDATL[7:0] Read/write value for Least Significant bits of program memory Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 187 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.6.3 NVMCON1 Name: Offset: NVMCON1 0x81E Nonvolatile Memory Control 1 Register Bit 7 Access Reset 6 5 4 3 2 1 0 NVMREGS LWLO FREE WRERR WREN WR RD R/W R/W R/S/HC R/W/HS R/W R/S/HC R/S/HC 0 0 0 x 0 0 0 Bit 6 - NVMREGS NVM Region Selection bit Value 1 0 Description Access EEPROM, DIA, DCI, Configuration, User ID and Device ID Registers Access Program Flash Memory Bit 5 - LWLO Load Write Latches Only bit Value 1 0 - Condition Description When FREE = 0 The next WR command updates the write latch for this word within the row; no memory operation is initiated. When FREE = 0 The next WR command writes data or erases Otherwise: This bit is ignored. Bit 4 - FREE Program Flash Memory Erase Enable bit Value 1 0 Description Performs an erase operation with the next WR command; the 32-word pseudo-row containing the indicated address is erased (to all 1s) to prepare for writing. The next WR command writes without erasing. Bit 3 - WRERR Write-Reset Error Flag bit(1,2,3) Reset States: POR/BOR = x All Other Resets = q Value 1 0 Description A write operation was interrupted by a Reset, interrupted unlock sequence, or WR was written to one while NVMADR points to a write-protected address. All write operations have completed normally. Bit 2 - WREN Program/Erase Enable bit Value 1 0 Description Allows program/erase cycles Inhibits programming/erasing of program Flash Bit 1 - WR Write Control bit(4,5,6) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 188 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control Value 1 0 1 0 Condition When NVMREG:NVMADR points to a Program Flash Memory location: When NVMREG:NVMADR points to a Program Flash Memory location: When NVMREG:NVMADR points to a EEPROM location: When NVMREG:NVMADR points to a EEPROM location: Description Initiates the operation indicated by table in "WRERR Bit" section. NVM program/erase operation is complete and inactive. Initiates an erase/program cycle at the corresponding EEPROM location. NVM program/erase operation is complete and inactive. Bit 0 - RD Read Control bit(7) Value 1 0 Description Initiates a read at address = NVMADR1, and loads data to NVMDAT Read takes one instruction cycle and the bit is cleared when the operation is complete. The bit can only be set (not cleared) in software. NVM read operation is complete and inactive Note: 1. Bit is undefined while WR = 1 (during the EEPROM write operation it may be `0' or `1'). 2. 3. Bit must be cleared by software; hardware will not clear this bit. Bit may be written to `1' by the user in order to implement test sequences. 4. This bit can only be set by following the sequence described in the "NVM Unlock Sequence" section. Operations are self-timed and the WR bit is cleared by hardware when complete. Once a write operation is initiated, setting this bit to zero will have no effect. Reading from EEPROM loads only NVMDATL. 5. 6. 7. Related Links NVM Unlock Sequence WRERR Bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 189 PIC16(L)F18424/44 (NVM) Nonvolatile Memory Control 13.6.4 NVMCON2 Name: Offset: NVMCON2 0x81F Nonvolatile Memory Control 2 Register Bit 7 6 5 4 3 2 1 0 NVMCON2[7:0] Access Reset WO WO WO WO WO WO WO WO 0 0 0 0 0 0 0 0 Bits 7:0 - NVMCON2[7:0] Flash Memory Unlock Pattern bits Note: To unlock writes, a 55h must be written first followed by an AAh before setting the WR bit of the NVMCON1 register. The value written to this register is used to unlock the writes. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 190 PIC16(L)F18424/44 I/O Ports 14. I/O Ports 14.1 PORT Availability Table 14-1. PORT Availability Per Device PORTs 14.2 PORT Description PORTA 6-bit wide, bidirectional port. PORTB 4-bit wide, bidirectional port. PORTC 6/8-bit wide, bidirectional port. PIC16(L)F18424 PIC16(L)F18444 * * * * * I/O Ports Description Each port has standard registers for its operation. These registers are: * * * * * * * * PORTx registers (reads the levels on the pins of the device) LATx registers (output latch) TRISx registers (data direction) ANSELx registers (analog select) WPUx registers (weak pull-up) INLVLx (input level control) SLRCONx registers (slew rate control) ODCONx registers (open-drain control) Most port pins share functions with device peripherals, both analog and digital. In general, when a peripheral is enabled on a port pin, that pin cannot be used as a general purpose output; however, the pin can still be read. The Data Latch (LATx registers) is useful for read-modify-write operations on the value that the I/O pins are driving. A write operation to the LATx register has the same effect as a write to the corresponding PORTx register. A read of the LATx register reads of the values held in the I/O PORT latches, while a read of the PORTx register reads the actual I/O pin value. Ports that support analog inputs have an associated ANSELx register. When an ANSELx bit is set, the digital input buffer associated with that bit is disabled. Disabling the input buffer prevents analog signal levels on the pin between a logic high and low from causing excessive current in the logic input circuitry. A simplified model of a generic I/O port, without the interfaces to other peripherals, is shown in the following figure: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 191 First Used: Note: PIC16F1508/9 PIC16(L)F18424/44 I/O Ports Figure 14-1. Generic I/O Port Operation Rev. 10-000052A 7/30/2013 Read LATx TRISx D Write LATx Write PORTx Q VDD CK Data Register Data bus I/O pin Read PORTx To digital peripherals ANSELx To analog peripherals VSS 14.3 I/O Priorities Each pin defaults to the PORT data latch after Reset. Other functions are selected with the peripheral pin select logic. See "Peripheral Pin Select (PPS) Module" for more information. Analog input functions, such as ADC and comparator inputs, are not shown in the peripheral pin select lists. These inputs are active when the I/O pin is set for Analog mode using the ANSELx register. Digital output functions may continue to control the pin when it is in Analog mode. Analog outputs, when enabled, take priority over digital outputs and force the digital output driver into a high-impedance state. The pin function priorities are as follows: 1. 2. 3. 4. Configuration bits Analog outputs (disable the input buffers) Analog inputs Port inputs and outputs from PPS Related Links (PPS) Peripheral Pin Select Module 14.4 PORTx Registers In this section the generic names such as PORTx, LATx, TRISx, etc. can be associated with PORTA, PORTB, PORTC, etc, depending on availability per device (see related link below). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 192 PIC16(L)F18424/44 I/O Ports Related Links PORT Availability 14.4.1 Data Register PORTx is a bidirectional port, and its corresponding data direction register is TRISx. Setting a TRISx bit (`1') will make the corresponding PORTx pin an input (i.e., disable the output driver). Clearing a TRISx bit (`0') will make the corresponding PORTx pin an output (i.e., it enables output driver and puts the contents of the output latch on the selected pin). The example below shows how to initialize PORTA. Reading the PORTx register reads the status of the pins, whereas writing to it will write to the PORT latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, this value is modified and then written to the PORT data latch (LATx). The PORT data latch LATx holds the output port data and contains the latest value of a LATx or PORTx write. EXAMPLE-1: Initializing PORTA ; This code example illustrates initializing the PORTA register. ; The other ports are initialized in the same manner. BANKSEL CLRF BANKSEL CLRF BANKSEL CLRF BANKSEL MOVLW MOVWF PORTA PORTA LATA LATA ANSELA ANSELA TRISA B'00111000' TRISA ; ;Init PORTA ;Data Latch ; ; ;digital I/O ; ;Set RA<5:3> as inputs ;and set RA<2:0> as outputs Related Links PORTA TRISA LATA 14.4.2 Direction Control The TRISx register controls the PORTx pin output drivers, even when they are being used as analog inputs. The user should ensure the bits in the TRISx register are maintained set when using them as analog inputs. I/O pins configured as analog inputs always read `0'. 14.4.3 Open-Drain Control The ODCONx register controls the open-drain feature of the port. Open-drain operation is independently selected for each pin. When an ODCONx bit is set, the corresponding port output becomes an open-drain driver capable of sinking current only. When an ODCONx bit is cleared, the corresponding port output pin is the standard push-pull drive capable of sourcing and sinking current. Important: It is not necessary to set open-drain control when using the pin for I2C; the I2C module controls the pin and makes the pin open-drain. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 193 PIC16(L)F18424/44 I/O Ports 14.4.4 Slew Rate Control The SLRCONx register controls the slew rate option for each port pin. Slew rate for each port pin can be controlled independently. When an SLRCONx bit is set, the corresponding port pin drive is slew rate limited. When an SLRCONx bit is cleared, The corresponding port pin drive slews at the maximum rate possible. 14.4.5 Input Threshold Control The INLVLx register controls the input voltage threshold for each of the available PORTx input pins. A selection between the Schmitt Trigger CMOS or the TTL compatible thresholds is available. The input threshold is important in determining the value of a read of the PORTx register and also the level at which an interrupt-on-change occurs, if that feature is enabled. See link below for more information on threshold levels. Important: Changing the input threshold selection should be performed while all peripheral modules are disabled. Changing the threshold level during the time a module is active may inadvertently generate a transition associated with an input pin, regardless of the actual voltage level on that pin. 14.4.6 Analog Control The ANSELx register is used to configure the Input mode of an I/O pin to analog. Setting the appropriate ANSELx bit high will cause all digital reads on the pin to be read as `0' and allow analog functions on the pin to operate correctly. The state of the ANSELx bits has no effect on digital output functions. A pin with TRIS clear and ANSEL set will still operate as a digital output, but the Input mode will be analog. This can cause unexpected behavior when executing READ-MODIFY-WRITE instructions on the affected port. Important: The ANSELx bits default to the Analog mode after Reset. To use any pins as digital general purpose or peripheral inputs, the corresponding ANSEL bits must be initialized to `0' by user software. 14.4.7 Weak Pull-up Control The WPUx register controls the individual weak pull-ups for each port pin. 14.4.8 PORTx Functions and Output Priorities Each PORTx pin is multiplexed with other functions. Each pin defaults to the PORT latch data after Reset. Other output functions are selected with the peripheral pin select logic, or by enabling an analog output, such as the DAC. See the link below for more information. Analog input functions, such as ADC and comparator inputs are not shown in the peripheral pin select lists. Digital output functions may continue to control the pin when it is in Analog mode. Related Links (PPS) Peripheral Pin Select Module (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 194 PIC16(L)F18424/44 I/O Ports 14.5 Register Summary - Input/Output Offset Name Bit Pos. 0x0C PORTA 7:0 0x0D PORTB 7:0 RB7 RB6 RB5 RB4 0x0E PORTC 7:0 RC7 RC6 RC5 RC4 TRISA5 TRISA4 RA5 RA4 RA3 RA2 RA1 RA0 RC3 RC2 RC1 RC0 TRISA2 TRISA1 TRISA0 TRISC2 TRISC1 TRISC0 LATA2 LATA1 LATA0 LATC2 LATC1 LATC0 ANSELA2 ANSELA1 ANSELA0 WPUA2 WPUA1 WPUA0 ODCA2 ODCA1 ODCA0 0x0F ... Reserved 0x11 0x12 TRISA 7:0 0x13 TRISB 7:0 TRISB7 TRISB6 TRISB5 TRISB4 0x14 TRISC 7:0 TRISC7 TRISC6 TRISC5 TRISC4 LATA5 LATA4 TRISC3 0x15 ... Reserved 0x17 0x18 LATA 7:0 0x19 LATB 7:0 LATB7 LATB6 LATB5 LATB4 0x1A LATC 7:0 LATC7 LATC6 LATC5 LATC4 LATC3 0x1B ... Reserved 0x1F37 0x1F38 ANSELA 7:0 ANSELA5 ANSELA4 0x1F39 WPUA 7:0 WPUA5 WPUA4 0x1F3A ODCONA 7:0 ODCA5 ODCA4 0x1F3B SLRCONA 7:0 SLRA5 SLRA4 0x1F3C INLVLA 7:0 INLVLA5 INLVLA4 WPUA3 SLRA2 SLRA1 SLRA0 INLVLA3 INLVLA2 INLVLA1 INLVLA0 0x1F3D ... Reserved 0x1F42 0x1F43 ANSELB 7:0 ANSELB7 ANSELB6 ANSELB5 ANSELB4 0x1F44 WPUB 7:0 WPUB7 WPUB6 WPUB5 WPUB4 0x1F45 ODCONB 7:0 ODCB7 ODCB6 ODCB5 ODCB4 0x1F46 SLRCONB 7:0 SLRB7 SLRB6 SLRB5 SLRB4 0x1F47 INLVLB 7:0 INLVLB7 INLVLB6 INLVLB5 INLVLB4 0x1F48 ... Reserved 0x1F4D 0x1F4E ANSELC 7:0 ANSELC7 ANSELC6 ANSELC5 ANSELC4 ANSELC3 ANSELC2 ANSELC1 ANSELC0 0x1F4F WPUC 7:0 WPUC7 WPUC6 WPUC5 WPUC4 WPUC3 WPUC2 WPUC1 WPUC0 0x1F50 ODCONC 7:0 ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 ODCC2 ODCC1 ODCC0 0x1F51 SLRCONC 7:0 SLRC7 SLRC6 SLRC5 SLRC4 SLRC3 SLRC2 SLRC1 SLRC0 0x1F52 INLVLC 7:0 INLVLC7 INLVLC6 INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 14.6 Register Definitions: Port Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 195 PIC16(L)F18424/44 I/O Ports 14.6.1 PORTA Name: Offset: PORTA 0x00C PORTA Register Bit 7 6 Access Reset 5 4 3 2 1 0 RA5 RA4 RA3 RA2 RA1 RA0 R/W R/W R/W R/W R/W R/W x x x x x x Bits 0, 1, 2, 3, 4, 5 - RAn Port I/O Value bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value 1 0 Description Port pin is VIH Port pin is VIL Note: * Writes to PORTA are actually written to the corresponding LATA register. Reads from PORTA register return actual I/O pin values. * Bits RA0, RA1 and RA3 are read-only when DEBUG is enabled, and will read `0'. * Bit RA3 will read `1' when MCLRE = 1 (master clear enabled) and '0' when DEBUG is enabled. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 196 PIC16(L)F18424/44 I/O Ports 14.6.2 PORTB Name: Offset: PORTB 0x00D PORTB Register Bit Access Reset 7 6 5 4 RB7 RB6 RB5 RB4 R/W R/W R/W R/W x x x x 3 2 1 0 Bits 4, 5, 6, 7 - RBn Port I/O Value bits Reset States: POR/BOR = xxxx All Other Resets = uuuu Value 1 0 Description Port pin is VIH Port pin is VIL Note: Writes to PORTB are actually written to the corresponding LATB register. Reads from PORTB register return actual I/O pin values. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 197 PIC16(L)F18424/44 I/O Ports 14.6.3 PORTC Name: Offset: PORTC 0x00E PORTC Register Bit Access Reset 7 6 5 4 3 2 1 0 RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 0, 1, 2, 3, 4, 5, 6, 7 - RCn Port I/O Value bits Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Value 1 0 Description Port pin is VIH Port pin is VIL Note: 1. Writes to PORTC are actually written to the corresponding LATC register. Reads from PORTC register return actual I/O pin values. 2. Bits RC6 and RC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 198 PIC16(L)F18424/44 I/O Ports 14.6.4 TRISA Name: Offset: TRISA 0x012 Tri-State Control Register Bit 7 6 Access Reset 5 4 TRISA5 TRISA4 R/W R/W 1 1 3 2 1 0 TRISA2 TRISA1 TRISA0 RO R/W R/W R/W 1 1 1 1 Bits 4, 5 - TRISAx TRISA Port I/O Tri-state Control bits Value 1 0 Description PORTA pin configured as an input (tri-stated) PORTA pin configured as an output Bits 0, 1, 2 - TRISAn TRISA Port I/O Tri-state Control bits Value 1 0 Description PORTA pin configured as an input (tri-stated) PORTA pin configured as an output Note: Bits TRISA0 and TRISA1 are read-only when DEBUG is enabled, and will read `1'. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 199 PIC16(L)F18424/44 I/O Ports 14.6.5 TRISB Name: Offset: TRISB 0x013 Tri-State Control Register Bit Access Reset 7 6 5 4 TRISB7 TRISB6 TRISB5 TRISB4 R/W R/W R/W R/W 1 1 1 1 3 2 1 0 Bits 4, 5, 6, 7 - TRISBn TRISB Port I/O Tri-state Control bits Value 1 0 Description PORTB pin configured as an input (tri-stated) PORTB pin configured as an output (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 200 PIC16(L)F18424/44 I/O Ports 14.6.6 TRISC Name: Offset: TRISC 0x014 Tri-State Control Register Bit Access Reset 7 6 5 4 3 2 1 0 TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 0, 1, 2, 3, 4, 5, 6, 7 - TRISCn TRISC Port I/O Tri-state Control bits Value 1 0 Description PORTC pin configured as an input (tri-stated) PORTC pin configured as an output Note: Bits TRISC6 and TRISC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 201 PIC16(L)F18424/44 I/O Ports 14.6.7 LATA Name: Offset: LATA 0x018 Output Latch Register Bit 7 6 Access Reset 5 4 LATA5 LATA4 R/W R/W x x 3 2 1 0 LATA2 LATA1 LATA0 RO R/W R/W R/W 1 x x x Bits 4, 5 - LATAn Output Latch A Value bits Reset States: POR/BOR = xx All Other Resets = uu Bits 0, 1, 2 - LATAn Output Latch A Value bits Reset States: POR/BOR = xxx All Other Resets = uuu Note: Writes to LATA are equivalent with writes to the corresponding PORTA register. Reads from LATA register return register values, not I/O pin values. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 202 PIC16(L)F18424/44 I/O Ports 14.6.8 LATB Name: Offset: LATB 0x019 Output Latch Register Bit Access Reset 7 6 5 4 LATB7 LATB6 LATB5 LATB4 R/W R/W R/W R/W x x x x 3 2 1 0 Bits 4, 5, 6, 7 - LATBn Output Latch B Value bits Reset States: POR/BOR = xxxx All Other Resets = uuuuu Note: Writes to LATB are equivalent with writes to the corresponding PORTB register. Reads from LATB register return register values, not I/O pin values. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 203 PIC16(L)F18424/44 I/O Ports 14.6.9 LATC Name: Offset: LATC 0x01A Output Latch Register Bit Access Reset 7 6 5 4 3 2 1 0 LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0 R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 0, 1, 2, 3, 4, 5, 6, 7 - LATCn Output Latch C Value bits Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuuu Note: 1. Writes to LATC are equivalent with writes to the corresponding PORTC register. Reads from LATC register return register values, not I/O pin values. 2. Bits LATC6 and LATC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 204 PIC16(L)F18424/44 I/O Ports 14.6.10 ANSELA Name: Offset: ANSELA 0x1F38 Analog Select Register Bit 7 6 Access Reset 5 4 2 1 0 ANSELA5 ANSELA4 3 ANSELA2 ANSELA1 ANSELA0 R/W R/W R/W R/W R/W 1 1 1 1 1 Bits 4, 5 - ANSELAn Analog Select on RA Pins Value 1 0 Description Analog input. Pin is assigned as analog input. Digital input buffer disabled. Digital I/O. Pin is assigned to port or digital special function. Bits 0, 1, 2 - ANSELAn Analog Select on RA Pins Value 1 0 Description Analog input. Pin is assigned as analog input. Digital input buffer disabled. Digital I/O. Pin is assigned to port or digital special function. Note: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to allow external control of the voltage on the pin. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 205 PIC16(L)F18424/44 I/O Ports 14.6.11 ANSELB Name: Offset: ANSELB 0x1F43 Analog Select Register Bit Access Reset 7 6 5 4 ANSELB7 ANSELB6 ANSELB5 ANSELB4 R/W R/W R/W R/W 1 1 1 1 3 2 1 0 Bits 4, 5, 6, 7 - ANSELBn Analog Select on RB Pins Value 1 0 Description Analog input. Pin is assigned as analog input. Digital input buffer disabled. Digital I/O. Pin is assigned to port or digital special function. Note: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to allow external control of the voltage on the pin. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 206 PIC16(L)F18424/44 I/O Ports 14.6.12 ANSELC Name: Offset: ANSELC 0x1F4E Analog Select Register Bit Access Reset 7 6 5 4 3 2 1 0 ANSELC7 ANSELC6 ANSELC5 ANSELC4 ANSELC3 ANSELC2 ANSELC1 ANSELC0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 0, 1, 2, 3, 4, 5, 6, 7 - ANSELCn Analog Select on RC Pins Value 1 0 Description Analog input. Pin is assigned as analog input. Digital input buffer disabled. Digital I/O. Pin is assigned to port or digital special function. Note: 1. When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to allow external control of the voltage on the pin. 2. Bits ANSC6 and ANSC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 207 PIC16(L)F18424/44 I/O Ports 14.6.13 WPUA Name: Offset: WPUA 0x1F39 Weak Pull-up Register Bit 7 6 Access Reset 5 4 3 2 1 0 WPUA5 WPUA4 WPUA3 WPUA2 WPUA1 WPUA0 R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5 - WPUAn Weak Pull-up PORTA Control bits Value 1 0 Description Weak Pull-up enabled Weak Pull-up disabled Note: 1. If MCLRE = 1, the weak pull-up in RA3 is always enabled; bit WPUA3 will read as '1'. 2. The weak pull-up device is automatically disabled if the pin is configured as an output. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 208 PIC16(L)F18424/44 I/O Ports 14.6.14 WPUB Name: Offset: WPUB 0x1F44 Weak Pull-up Register Bit Access Reset 7 6 5 4 WPUB7 WPUB6 WPUB5 WPUB4 R/W R/W R/W R/W 0 0 0 0 3 2 1 0 Bits 4, 5, 6, 7 - WPUBn Weak Pull-up PORTB Control bits Value 1 0 Description Weak Pull-up enabled Weak Pull-up disabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 209 PIC16(L)F18424/44 I/O Ports 14.6.15 WPUC Name: Offset: WPUC 0x1F4F Weak Pull-up Register Bit Access Reset 7 6 5 4 3 2 1 0 WPUC7 WPUC6 WPUC5 WPUC4 WPUC3 WPUC2 WPUC1 WPUC0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5, 6, 7 - WPUCn Weak Pull-up PORTC Control bits Value 1 0 Description Weak Pull-up enabled Weak Pull-up disabled Note: Bits WPUC6 and WPUC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 210 PIC16(L)F18424/44 I/O Ports 14.6.16 ODCONA Name: Offset: ODCONA 0x1F3A Open-Drain Control Register Bit 7 6 Access Reset 5 4 2 1 0 ODCA5 ODCA4 3 ODCA2 ODCA1 ODCA0 R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4, 5 - ODCAn Open-Drain Configuration on RA Pins Value 1 0 Description Port pin operates as open-drain drive (sink current only) Port pin operates as standard push-pull drive (source and sink current) Bits 0, 1, 2 - ODCAn Open-Drain Configuration on RA Pins Value 1 0 Description Port pin operates as open-drain drive (sink current only) Port pin operates as standard push-pull drive (source and sink current) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 211 PIC16(L)F18424/44 I/O Ports 14.6.17 ODCONB Name: Offset: ODCONB 0x1F45 Open-Drain Control Register Bit Access Reset 7 6 5 4 ODCB7 ODCB6 ODCB5 ODCB4 R/W R/W R/W R/W 0 0 0 0 3 2 1 0 Bits 4, 5, 6, 7 - ODCBn Open-Drain Configuration on RB Pins Value 1 0 Description Port pin operates as open-drain drive (sink current only) Port pin operates as standard push-pull drive (source and sink current) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 212 PIC16(L)F18424/44 I/O Ports 14.6.18 ODCONC Name: Offset: ODCONC 0x1F50 Open-Drain Control Register Bit Access Reset 7 6 5 4 3 2 1 0 ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 ODCC2 ODCC1 ODCC0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5, 6, 7 - ODCCn Open-Drain Configuration on RC Pins Value 1 0 Description Port pin operates as open-drain drive (sink current only) Port pin operates as standard push-pull drive (source and sink current) Note: Bits ODCC6 and ODCC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 213 PIC16(L)F18424/44 I/O Ports 14.6.19 SLRCONA Name: Offset: SLRCONA 0x1F3B Slew Rate Control Register Bit 7 6 Access Reset 5 4 2 1 0 SLRA5 SLRA4 3 SLRA2 SLRA1 SLRA0 R/W R/W R/W R/W R/W 1 1 1 1 1 Bits 4, 5 - SLRAn Slew Rate Control on RA Pins Value 1 0 Description Port pin slew rate is limited Port pin slews at maximum rate Bits 0, 1, 2 - SLRAn Slew Rate Control on RA Pins Value 1 0 Description Port pin slew rate is limited Port pin slews at maximum rate (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 214 PIC16(L)F18424/44 I/O Ports 14.6.20 SLRCONB Name: Offset: SLRCONB 0x1F46 Slew Rate Control Register Bit Access Reset 7 6 5 4 SLRB7 SLRB6 SLRB5 SLRB4 R/W R/W R/W R/W 1 1 1 1 3 2 1 0 Bits 4, 5, 6, 7 - SLRBn Slew Rate Control on RB Pins Value 1 0 Description Port pin slew rate is limited Port pin slews at maximum rate (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 215 PIC16(L)F18424/44 I/O Ports 14.6.21 SLRCONC Name: Offset: SLRCONC 0x1F51 Slew Rate Control Register Bit Access Reset 7 6 5 4 3 2 1 0 SLRC7 SLRC6 SLRC5 SLRC4 SLRC3 SLRC2 SLRC1 SLRC0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 0, 1, 2, 3, 4, 5, 6, 7 - SLRCn Slew Rate Control on RC Pins Value 1 0 Description Port pin slew rate is limited Port pin slews at maximum rate Note: Bits SLRC6 and SLRC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 216 PIC16(L)F18424/44 I/O Ports 14.6.22 INLVLA Name: Offset: INLVLA 0x1F3C Input Level Control Register Bit 7 6 Access Reset 5 4 3 2 1 0 INLVLA5 INLVLA4 INLVLA3 INLVLA2 INLVLA1 INLVLA0 R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 Bits 0, 1, 2, 3, 4, 5 - INLVLAn Input Level Select on RA Pins Value 1 0 Description ST input used for port reads and interrupt-on-change TTL input used for port reads and interrupt-on-change (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 217 PIC16(L)F18424/44 I/O Ports 14.6.23 INLVLB Name: Offset: INLVLB 0x1F47 Input Level Control Register Bit Access Reset 7 6 5 4 INLVLB7 INLVLB6 INLVLB5 INLVLB4 R/W R/W R/W R/W 1 1 1 1 3 2 1 0 Bits 4, 5, 6, 7 - INLVLBn Input Level Select on RB Pins Value 1 0 Description ST input used for port reads and interrupt-on-change TTL input used for port reads and interrupt-on-change (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 218 PIC16(L)F18424/44 I/O Ports 14.6.24 INLVLC Name: Offset: INLVLC 0x1F52 Input Level Control Register Bit Access Reset 7 6 5 4 3 2 1 0 INLVLC7 INLVLC6 INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 0, 1, 2, 3, 4, 5, 6, 7 - INLVLCn Input Level Select on RC Pins Value 1 0 Description ST input used for port reads and interrupt-on-change TTL input used for port reads and interrupt-on-change Note: Bits INLVLC6 and INLVLC7 available on 20-pin or higher pin count devices only; Bits unimplemented for lower pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 219 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module 15. (PPS) Peripheral Pin Select Module The Peripheral Pin Select (PPS) module connects peripheral inputs and outputs to the device I/O pins. Filename: 10-000262E.pdf Only are included Title:digital signals PPS Block Diagram in the selections. 6/27/2017 Last Edit: AllFirst analog outputs remain fixed to their assigned pins. Input and output selections are PIC16(L)F18xx Used: inputs and Note: 1. Not available on devices. independent as shown14-Pin in the figure below. Figure 15-1. Simplified PPS Block Diagram Rev. 10-000262E 6/27/2017 RA0PPS abcPPS RA0 RA0 Peripheral abc RxyPPS Rxy Peripheral xyz RC7PPS(1) RC7(1) xyzPPS RC7(1) Note: 1. Not present on 14-pin devices. 15.1 PPS Inputs Each peripheral has an xxxPPS register with which the input pin to the peripheral is selected. Not all ports are available for input as shown in the following table. Multiple peripherals can operate from the same source simultaneously. Port reads always return the pin level regardless of peripheral PPS selection. If a pin also has analog functions associated, the ANSEL bit for that pin must be cleared to enable the digital input buffer. Important: The notation "xxx" in the generic register name is a place holder for the peripheral identifier. For example, xxx = INT for the INTPPS register. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 220 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module Table 15-1. PPS Input Signal Routing Options Input Signal Name Input Register Name INT Default location at POR Reset Value (xxxPPS<4:0>) 14/16-pin devices 20-pin devices 14/16-pin devices 20-pin devices INTPPS RA2 RA2 00010 00010 T0CKI T0CKIPPS RA2 RA2 00010 00010 T1CKI T1CKIPPS RA5 RA5 00101 00101 T1G T1GPPS RA4 RA4 00100 00100 T2IN T2INPPS RA5 RA5 00101 00101 T3CKI T3CKIPPS RC5 RC5 10101 10101 T3G T3GPPS RC4 RC4 10100 10100 T4IN T4INPPS RC1 RC1 10001 10001 T5CKI T5CKIPPS RC0 RC0 10000 10000 T5G T5GPPS RC3 RC3 10011 10011 T6IN T6INPPS RC2 RC2 10010 10010 MDCARL MDCARLPPS RC2 RC2 10010 10010 MDCARH MDCARHPPS RC5 RC5 10101 10101 MDSRC MDSRCPPS RA1 RA1 00001 00001 CCP1IN CCP1INPPS RC5 RC5 10101 10101 CCP2IN CCP2INPPS RC3 RC3 10011 10011 CCP3IN CCP3INPPS RA2 RA2 00010 00010 CCP4IN CCP4INPPS RA4 RA4 00100 00100 CWG1IN CWG1INPPS RA2 RA2 00010 00010 CWG2IN CWG2INPPS RA2 RA2 00010 00010 CLCIN0 CLCIN0PPS RC3 RA2 10011 00010 CLCIN1 CLCIN1PPS RC4 RC3 10100 10011 CLCIN2 CLCIN2PPS RC1 RB4 10001 01100 CLCIN3 CLCIN3PPS RA5 RB5 00101 01101 ADACT ADACTPPS RC2 RC2 10010 10010 SCK1 SCL1PPS RC0 RB6 10000 01110 SCL1 SCL1PPS RC0 RB6 10000 01110 SDI1 SDA1PPS RC1 RB4 10001 01100 SDA1 SDA1PPS RC1 RB4 10001 01100 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 221 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module Input Signal Name Input Register Name SS1 Default location at POR Reset Value (xxxPPS<4:0>) 14/16-pin devices 20-pin devices 14/16-pin devices 20-pin devices SS1PPS RC3 RC6 10011 10110 RX1 RX1PPS RC5 RB5 10101 01101 DT1(1) RX1PPS RC5 RB5 10101 01101 CK1(1) CK1PPS RC4 RB7 10100 01111 SMT1SIG SMT1SIGPPS RC0 RC0 10000 10000 SMT1WIN SMT1WINPPS RA5 RA5 00100 00100 Note: 1. DT1 and CK1 are bidirectional signals used in EUSART Synchronous mode. 15.2 PPS Outputs Each I/O pin has an RxyPPS register with which the pin output source is selected. With few exceptions, the port TRIS control associated with that pin retains control over the pin output driver. Peripherals that control the pin output driver as part of the peripheral operation will override the TRIS control as needed. These peripherals include: * * EUSART (synchronous operation) MSSP (I2C) Although every pin has its own RxyPPS peripheral selection register, the selections are identical for every pin as shown in the following table. Important: The notation "Rxy" is a place holder for the pin identifier. The 'x' holds the place of the PORT letter and the 'y' holds the place of the bit number. For example, Rxy = RA0 for the RA0PPS register. Table 15-2. PPS Output Signal Routing Options Output Signal Name RxyPPS Register Value ADCGRDA 0x1F ADCGRDB 0x20 C1OUT 0x11 C2OUT 0x12 CCP1OUT 0x09 CCP2OUT 0x0A CCP3OUT 0x0B CCP4OUT 0x0C (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 222 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module Output Signal Name RxyPPS Register Value CLC1OUT 0x01 CLC2OUT 0x02 CLC3OUT 0x03 CLC4OUT 0x04 CK(1)/TX1 0x0F CLKR 0x19 CWG1A 0x05 CWG1B 0x06 CWG1C 0x07 CWG1D 0x08 CWG2A 0x1B CWG2B 0x1C CWG2C 0x1D CWG2D 0x1E DSM1OUT 0x1A DT(1) 0x10 NCO1OUT 0x18 PWM6OUT 0x0D PWM7OUT 0x0E SCK1 0x13 SCL1 0x13 SDA1 0x14 SDO1 0x14 TMR0OUT 0x17 Note: 1. CK1 and DT1 are bidirectional signals used in EUSART Synchronous mode. 15.3 Bidirectional Pins PPS selections for peripherals with bidirectional signals on a single pin must be made so that the PPS input and PPS output select the same pin. Peripherals that have bidirectional signals include: * * EUSART (DT/RXxPPS and TX/CKxPPS pins for synchronous operation) MSSP (I2C SDA/SSPxDATPPS and SCL/SSPxCLKPPS) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 223 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module Important: The I2C default inputs, and a limited number of other alternate pins, are I2C and SMBus compatible. Clock and data signals can be routed to any pin, however pins without I2C compatibility will operate at standard TTL/ST logic levels as selected by the INLVL register. See the INLVL register for each port to determine which pins are I2C and SMBus compatible. 15.4 PPS Lock The PPS includes a mode in which all input and output selections can be locked to prevent inadvertent changes. PPS selections are locked by setting the PPSLOCKED bit of the PPSLOCK register. Setting and clearing this bit requires a special sequence as an extra precaution against inadvertent changes. Examples of setting and clearing the PPSLOCKED bit are shown in the following examples. PPS Lock Sequence ; suspend interrupts BCF INTCON,GIE BANKSEL PPSLOCK ; set bank ; required sequence, next 5 instructions MOVLW 0x55 MOVWF PPSLOCK MOVLW 0xAA MOVWF PPSLOCK ; Set PPSLOCKED bit to disable writes or BSF PPSLOCK,PPSLOCKED ; restore interrupts BSF INTCON,GIE PPS Unlock Sequence ; suspend interrupts BCF INTCON,GIE BANKSEL PPSLOCK ; set bank ; required sequence, next 5 instructions MOVLW 0x55 MOVWF PPSLOCK MOVLW 0xAA MOVWF PPSLOCK ; Clear PPSLOCKED bit to enable writes BCF PPSLOCK,PPSLOCKED ; restore interrupts BSF INTCON,GIE Note: 1. The PPSLOCK bit can only be set or cleared after the unlock sequence shown above. 2. If PPS1WAY = 1, the PPSLOCK bit cannot be cleared after it has been set. 15.5 PPS Permanent Lock The PPS can be permanently locked by setting the PPS1WAY Configuration bit. When this bit is set, the PPSLOCKED bit can only be cleared and set one time after a device Reset. This allows for clearing the PPSLOCKED bit so that the input and output selections can be made during initialization. When the PPSLOCKED bit is set after all selections have been made, it will remain set and cannot be cleared until after the next device Reset event. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 224 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module Related Links PPSLOCK 15.6 Operation During Sleep PPS input and output selections are unaffected by Sleep. 15.7 Effects of a Reset A device Power-on-Reset (POR) clears all PPS input and output selections to their default values. All other Resets leave the selections unchanged. Default input selections are shown in the input selection register table. The PPS one-way is also removed. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 225 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module 15.8 Register Summary - PPS Note: PORTB associated RxyPPS register as well as RC6PPS and RC7PPS registers are only available for 20-pin or higher pin count devices. Offset Name Bit Pos. 0x1E8F PPSLOCK 7:0 PPSLOCKED 0x1E90 INTPPS 7:0 PORT[1:0] PIN[2:0] 0x1E91 T0CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E92 T1CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E93 T1GPPS 7:0 PORT[1:0] PIN[2:0] 0x1E94 T3CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E95 T3GPPS 7:0 PORT[1:0] PIN[2:0] 0x1E96 T5CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E97 T5GPPS 7:0 PORT[1:0] PIN[2:0] 0x1E98 ... Reserved 0x1E9B 0x1E9C T2INPPS 7:0 PORT[1:0] PIN[2:0] 0x1E9D T4INPPS 7:0 PORT[1:0] PIN[2:0] 0x1E9E T6INPPS 7:0 PORT[1:0] PIN[2:0] 0x1E9F ... Reserved 0x1EA0 0x1EA1 CCP1PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA2 CCP2PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA3 CCP3PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA4 CCP4PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA5 ... Reserved 0x1EA8 0x1EA9 SMT1WINPPS 7:0 PORT[1:0] PIN[2:0] 0x1EAA SMT1SIGPPS 7:0 PORT[1:0] PIN[2:0] 0x1EAB ... Reserved 0x1EB0 0x1EB1 CWG1PPS 7:0 PORT[1:0] PIN[2:0] 0x1EB2 CWG2PPS 7:0 PORT[1:0] PIN[2:0] 0x1EB3 ... Reserved 0x1EB7 0x1EB8 MDCARLPPS 7:0 PORT[1:0] PIN[2:0] 0x1EB9 MDCARHPPS 7:0 PORT[1:0] PIN[2:0] 0x1EBA MDSRCPPS 7:0 PORT[1:0] PIN[2:0] 0x1EBB CLCIN0PPS 7:0 PORT[1:0] PIN[2:0] 0x1EBC CLCIN1PPS 7:0 PORT[1:0] PIN[2:0] 0x1EBD CLCIN2PPS 7:0 PORT[1:0] PIN[2:0] 0x1EBE CLCIN3PPS 7:0 PORT[1:0] PIN[2:0] (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 226 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module Offset Name Bit Pos. 0x1EBF ... Reserved 0x1EC2 0x1EC3 ADACTPPS 0x1EC4 Reserved 7:0 PORT[1:0] PIN[2:0] 0x1EC5 SSP1CLKPPS 7:0 PORT[1:0] PIN[2:0] 0x1EC6 SSP1DATPPS 7:0 PORT[1:0] PIN[2:0] 0x1EC7 SSP1SSPPS 7:0 PORT[1:0] PIN[2:0] 0x1EC8 ... Reserved 0x1ECA 0x1ECB RX1PPS 7:0 PORT[1:0] PIN[2:0] 0x1ECC CK1PPS 7:0 PORT[1:0] PIN[2:0] 0x1ECD ... Reserved 0x1F0F 0x1F10 RA0PPS 7:0 PPS[5:0] 0x1F11 RA1PPS 7:0 PPS[5:0] 0x1F12 RA2PPS 7:0 PPS[5:0] 0x1F13 Reserved 0x1F14 RA4PPS 7:0 PPS[5:0] 0x1F15 RA5PPS 7:0 PPS[5:0] 0x1F16 ... Reserved 0x1F1B 0x1F1C RB4PPS 7:0 PPS[5:0] 0x1F1D RB5PPS 7:0 PPS[5:0] 0x1F1E RB6PPS 7:0 PPS[5:0] 0x1F1F RB7PPS 7:0 PPS[5:0] 0x1F20 RC0PPS 7:0 PPS[5:0] 0x1F21 RC1PPS 7:0 PPS[5:0] 0x1F22 RC2PPS 7:0 PPS[5:0] 0x1F23 RC3PPS 7:0 PPS[5:0] 0x1F24 RC4PPS 7:0 PPS[5:0] 0x1F25 RC5PPS 7:0 PPS[5:0] 0x1F26 RC6PPS 7:0 PPS[5:0] 0x1F27 RC7PPS 7:0 PPS[5:0] 15.9 Register Definitions: PPS Input and Output Selection (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 227 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module 15.9.1 Peripheral xxx Input Selection Name: xxxPPS Important: The Reset value of this register is determined by the device default for each peripheral. Refer to the input selection table for a list of available ports and default pin locations. Bit 7 6 5 4 3 2 PORT[1:0] Access Reset 1 0 PIN[2:0] R/W R/W R/W R/W R/W g g g g g Bits 4:3 - PORT[1:0] Peripheral xxx Input PORT Selection bits See the input selection table for a list of available ports and default pin locations. Value 10 01 00 Description PORTC PORTB PORTA Bits 2:0 - PIN[2:0] Peripheral xxx Input Pin Selection bits Value 111 110 101 100 011 010 001 000 Description Peripheral input is from PORTx Pin 7 (Rx7) Peripheral input is from PORTx Pin 6 (Rx6) Peripheral input is from PORTx Pin 5 (Rx5) Peripheral input is from PORTx Pin 4 (Rx4) Peripheral input is from PORTx Pin 3 (Rx3) Peripheral input is from PORTx Pin 2 (Rx2) Peripheral input is from PORTx Pin 1 (Rx1) Peripheral input is from PORTx Pin 0 (Rx0) Important: PORTB is available only for 20-pin or higher pin count devices. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 228 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module 15.9.2 Pin Rxy Output Source Selection Register Name: RxyPPS Important: See Register Summary - PPS for the address offset of each individual register. Bit 7 6 5 4 3 2 1 0 RxyPPS[5:0] Access Reset R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 5:0 - RxyPPS[5:0] Pin Rxy Output Source Selection bits See output source selection table for source codes. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 229 PIC16(L)F18424/44 (PPS) Peripheral Pin Select Module 15.9.3 PPS Lock Register Name: Offset: Bit 7 PPSLOCK 0x1E8F 6 5 4 3 2 1 0 PPSLOCKED Access R/W Reset 0 Bit 0 - PPSLOCKED PPS Locked bit Value 1 0 Description PPS is locked. PPS selections can not be changed. PPS is not locked. PPS selections can be changed. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 230 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16. (PMD) Peripheral Module Disable This module provides the ability to selectively enable or disable a peripheral. Disabling a peripheral places it in its lowest possible power state. The user can disable unused modules to reduce the overall power consumption. The PIC16(L)F18424/44 devices address this requirement by allowing peripheral modules to be selectively enabled or disabled. Disabling a peripheral places it in the lowest possible power mode. Important: All modules are ON by default following any system Reset. 16.1 Disabling a Module A peripheral can be disabled by setting the corresponding peripheral disable bit in the PMDx register. Disabling a module has the following effects: * * * 16.2 The module is held in Reset and does not function. All the SFRs pertaining to that peripheral become "unimplemented" - Writing is disabled - Reading returns 0x00 Module outputs are disabled Enabling a Module Clearing the corresponding module disable bit in the PMDx register, re-enables the module and the SFRs will reflect the Power-on Reset values. Important: There should be no reads/writes to the module SFRs for at least two instruction cycles after it has been re-enabled. 16.3 System Clock Disable Setting SYSCMD disables the system clock (FOSC) distribution network to the peripherals. Not all peripherals make use of SYSCLK, so not all peripherals are affected. Refer to the specific peripheral description to see if it will be affected by this bit. Related Links PMD0 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 231 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.4 Register Summary - PMD Offset Name Bit Pos. 0x0796 PMD0 7:0 0x0797 PMD1 7:0 0x0798 PMD2 7:0 SYSCMD FVRMD TMR6MD TMR5MD CLKRMD IOCMD TMR3MD TMR2MD TMR1MD TMR0MD C2MD C1MD ZCDMD CCP4MD CCP3MD CCP2MD CCP1MD CLC3MD CLC2MD CLC1MD NCO1MD 0x0799 PMD3 7:0 DAC1MD ADCMD 0x079A PMD4 7:0 PWM7MD PWM6MD 0x079B PMD5 7:0 CWG2MD CWG1MD 0x079C PMD6 7:0 0x079D PMD7 7:0 16.5 TMR4MD NVMMD UART1MD SMT1MD CLC4MD MSSP1MD DSM1MD Register Definitions: Peripheral Module Disable (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 232 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.1 PMD0 Name: Offset: PMD0 0x796 PMD Control Register 0 Bit Access Reset 7 6 2 1 0 SYSCMD FVRMD 5 4 3 NVMMD CLKRMD IOCMD R/W R/W R/W R/W R/W 0 0 0 0 0 Bit 7 - SYSCMD Disable Peripheral System Clock Network bit Disables the System clock network Value 1 0 Description System clock network disabled (FOSC) System clock network enabled Bit 6 - FVRMD Disable Fixed Voltage Reference bit Value 1 0 Description FVR module disabled FVR module enabled Bit 2 - NVMMD NVM Module Disable bit(1) Disables the NVM module Value 1 0 Description All Memory reading and writing is disabled; NVMCON registers cannot be written; FSR access to these locations returns zero. NVM module enabled Bit 1 - CLKRMD Disable Clock Reference bit Value 1 0 Description CLKR module disabled CLKR module enabled Bit 0 - IOCMD Disable Interrupt-on-Change bit, All Ports Value 1 0 Description IOC module(s) disabled IOC module(s) enabled Note: 1. When enabling NVM, a delay of up to 1 s may be required before accessing data. Related Links System Clock Disable (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 233 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.2 PMD1 Name: Offset: PMD1 0x797 PMD Control Register 1 Bit 7 Access Reset 6 5 4 3 2 1 0 TMR6MD TMR5MD TMR4MD TMR3MD TMR2MD TMR1MD TMR0MD R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5, 6 - TMRnMD Disable Timer n bit Value 1 0 Description TMRn module disabled TMRn module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 234 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.3 PMD2 Name: Offset: PMD2 0x798 PMD Control Register 2 Bit 7 6 5 4 3 2 1 0 NCO1MD Access Reset R/W 0 Bit 7 - NCO1MD Disable Numerically Control Oscillator bit Value 1 0 Description NCO1 module disabled NCO1 module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 235 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.4 PMD3 Name: Offset: PMD3 0x799 PMD Control Register 3 Bit 7 Access Reset 6 5 2 1 0 DAC1MD ADCMD 4 3 C2MD C1MD ZCDMD R/W R/W R/W R/W R/W 0 0 0 0 0 Bit 6 - DAC1MD Disable DAC1 bit Value 1 0 Description DAC module disabled DAC module enabled Bit 5 - ADCMD Disable ADC bit Value 1 0 Description ADC module disabled ADC module enabled Bit 2 - C2MD Disable Comparator C2 bit Value 1 0 Description C2 module disabled C2 module enabled Bit 1 - C1MD Disable Comparator C1 bit Value 1 0 Description C1 module disabled C1 module enabled Bit 0 - ZCDMD Disable Zero-Cross Detect module bit Value 1 0 Description ZCD module disabled ZCD module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 236 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.5 PMD4 Name: Offset: PMD4 0x79A PMD Control Register 4 Bit 7 Access Reset 6 5 3 2 1 0 PWM7MD PWM6MD 4 CCP4MD CCP3MD CCP2MD CCP1MD R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bit 6 - PWM7MD Disable Pulse-Width Modulator PWM7 bit Value 1 0 Description PWM7 module disabled PWM7 module enabled Bit 5 - PWM6MD Disable Pulse-Width Modulator PWM6 bit Value 1 0 Description PWM6 module disabled PWM6 module enabled Bit 3 - CCP4MD Disable Pulse-Width Modulator CCP4 bit Value 1 0 Description CCP4 module disabled CCP4 module enabled Bit 2 - CCP3MD Disable Pulse-Width Modulator CCP3 bit Value 1 0 Description CCP3 module disabled CCP3 module enabled Bit 1 - CCP2MD Disable Pulse-Width Modulator CCP2 bit Value 1 0 Description CCP2 module disabled CCP2 module enabled Bit 0 - CCP1MD Disable Pulse-Width Modulator CCP1 bit Value 1 0 Description CCP1 module disabled CCP1 module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 237 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.6 PMD5 Name: Offset: PMD5 0x79B PMD Control Register 5 Bit 7 Access Reset 6 5 CWG2MD CWG1MD R/W R/W 0 0 4 3 2 1 0 Bit 6 - CWG2MD Disable CWG2 bit Value 1 0 Description CWG2 module disabled CWG2 module enabled Bit 5 - CWG1MD Disable CWG1 bit Value 1 0 Description CWG1 module disabled CWG1 module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 238 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.7 PMD6 Name: Offset: PMD6 0x79C PMD Control Register 6 Bit 7 6 5 Access Reset 4 3 2 1 0 UART1MD MSSP1MD R/W R/W 0 0 Bit 4 - UART1MD Disable EUSART1 bit Value 1 0 Description EUSART1 module disabled EUSART1 module enabled Bit 0 - MSSP1MD Disable MSSP1 bit Value 1 0 Description MSSP1 module disabled MSSP1 module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 239 PIC16(L)F18424/44 (PMD) Peripheral Module Disable 16.5.8 PMD7 Name: Offset: PMD7 0x79D PMD Control Register 7 Bit 7 6 Access Reset 5 4 3 2 1 0 SMT1MD CLC4MD CLC3MD CLC2MD CLC1MD DSM1MD R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bit 5 - SMT1MD Disable Signal Measurement Timer1 bit Value 1 0 Description SMT1 module disabled SMT1 module enabled Bits 1, 2, 3, 4 - CLCnMD Disable CLCn bit Value 1 0 Description CLCn module disabled CLCn module enabled Bit 0 - DSM1MD Disable Data Signal Modulator 1 bit Value 1 0 Description DSM1 module disabled DSM1 module enabled (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 240 PIC16(L)F18424/44 Interrupt-on-Change 17. Interrupt-on-Change An interrupt can be generated by detecting a signal that has either a rising edge or a falling edge. Any individual pin, or combination of pins, can be configured to generate an interrupt. The interrupt-on-change module has the following features: * Interrupt-on-Change enable (Master Switch) * Individual pin configuration * Rising and falling edge detection * Individual pin interrupt flags Filename: 10-000037A.vsd Block Diagram (PortAmodule. Example) TheTitle: following figureInterrupt-on-change is a block diagram of the IOC Last Edit: 6/2/2014 First Used: PIC16(L)F1508/0 (LECD) Figure 17-1. Interrupt-on-Change Block Diagram (PORTA Example) Rev. 10-000 037A 6/2/201 4 IOCANx D Q R Q4Q1 edge detect RAx IOCAPx D data bus = 0 or 1 Q D S to data bus IOCAFx Q write IOCAFx R IOCIE Q2 IOC interrupt to CPU core from all other IOCnFx individual pin detectors Note: See link below for BOR Active Conditions. FOSC Q1 17.1 Q1 Q2 Enabling the Module Q1 Q2 Q2 Q3 Q3 Q3 To allow individual port pins to generate an interrupt, the IOCIE bit of the PIE0 register must be set. If the Q4 Q4 Q4 IOCIE bit is disabled, the edge detection on the pin will still occur, but an interrupt will not be generated. Q4Q1 Q4Q1 Q4Q1 Q4Q1 Related Links PIE0 17.2 Individual Pin Configuration For each port pin, a rising edge detector and a falling edge detector are present. To enable a pin to detect a rising edge, the associated bit of the IOCxP register is set. To enable a pin to detect a falling edge, the associated bit of the IOCxN register is set. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 241 PIC16(L)F18424/44 Interrupt-on-Change A pin can be configured to detect rising and falling edges simultaneously by setting both associated bits of the IOCxP and IOCxN registers, respectively. 17.3 Interrupt Flags The bits located in the IOCxF registers are status flags that correspond to the interrupt-on-change pins of each port. If an expected edge is detected on an appropriately enabled pin, then the status flag for that pin will be set, and an interrupt will be generated if the IOCIE bit is set. The IOCIF bit of the PIR0 register reflects the status of all IOCxF bits. Related Links PIR0 17.3.1 Clearing Interrupt Flags The individual status flags, (IOCxF register bits), can be cleared by resetting them to zero. If another edge is detected during this clearing operation, the associated status flag will be set at the end of the sequence, regardless of the value actually being written. In order to ensure that no detected edge is lost while clearing flags, only AND operations masking out known changed bits should be performed. The following sequence is an example of what should be performed. Clearing Interrupt Flags (PORTA Example) MOVLW XORWF ANDWF 17.4 0xff IOCAF, W IOCAF, F Operation in Sleep The interrupt-on-change interrupt sequence will wake the device from Sleep mode, if the IOCIE bit is set. If an edge is detected while in Sleep mode, the IOCxF register will be updated prior to the first instruction executed out of Sleep. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 242 PIC16(L)F18424/44 Interrupt-on-Change 17.5 Register Summary - Interrupt-on-Change Note: PORTB associated registers as well as IOCCx6 and IOCCx7 bits are available for 20-pin or higher pin count devices only . Offset Name Bit Pos. 0x1F3D IOCAP 7:0 IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0 0x1F3E IOCAN 7:0 IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0 0x1F3F IOCAF 7:0 IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0 0x1F40 ... Reserved 0x1F47 0x1F48 IOCBP 7:0 IOCBP7 IOCBP6 IOCBP5 IOCBP4 0x1F49 IOCBN 7:0 IOCBN7 IOCBN6 IOCBN5 IOCBN4 0x1F4A IOCBF 7:0 IOCBF7 IOCBF6 IOCBF5 IOCBF4 0x1F4B ... Reserved 0x1F52 0x1F53 IOCCP 7:0 IOCCP7 IOCCP6 IOCCP5 IOCCP4 IOCCP3 IOCCP2 IOCCP1 IOCCP0 0x1F54 IOCCN 7:0 IOCCN7 IOCCN6 IOCCN5 IOCCN4 IOCCN3 IOCCN2 IOCCN1 IOCCN0 0x1F55 IOCCF 7:0 IOCCF7 IOCCF6 IOCCF5 IOCCF4 IOCCF3 IOCCF2 IOCCF1 IOCCF0 17.6 Register Definitions: Interrupt-on-Change Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 243 PIC16(L)F18424/44 Interrupt-on-Change 17.6.1 IOCAP Name: Offset: IOCAP 0x1F3D Interrupt-on-Change Positive Edge Register Bit 7 6 Access Reset 5 4 3 2 1 0 IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0 R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5 - IOCAPn Interrupt-on-Change Positive Edge Enable bits Value 1 0 Description Interrupt-on-Change enabled on the IOCA pin for a positive-going edge. Associated Status bit and interrupt flag will be set upon detecting an edge. Interrupt-on-Change disabled for the associated pin. Note: 1. IOCAP0 and IOCAP1 are not available for use if the debugger is enabled. 2. If MCLRE = 1 or LVP = 1, port functionality is disabled and IOCAP3 is not available. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 244 PIC16(L)F18424/44 Interrupt-on-Change 17.6.2 IOCAN Name: Offset: IOCAN 0x1F3E Interrupt-on-Change Negative Edge Register Bit 7 6 Access Reset 5 4 3 2 1 0 IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0 R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5 - IOCANn Interrupt-on-Change Negative Edge Enable bits Value 1 0 Description Interrupt-on-Change enabled on the IOCA pin for a negative-going edge. Associated Status bit and interrupt flag will be set upon detecting an edge. Interrupt-on-Change disabled for the associated pin Note: 1. IOCAN0 and IOCAN1 are not available for use if the debugger is enabled. 2. If MCLRE = 1 or LVP = 1, port functionality is disabled and IOCAN3 is not available. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 245 PIC16(L)F18424/44 Interrupt-on-Change 17.6.3 IOCAF Name: Offset: IOCAF 0x1F3F PORTA Interrupt-on-Change Flag Register Bit 7 6 Access Reset 5 4 3 2 1 0 IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0 R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5 - IOCAFn Interrupt-on-Change Flag bits Value 1 1 0 Condition IOCAP[n]=1 IOCAN[n]=1 IOCAP[n]=x and IOCAN[n]=x Description A positive edge was detected on the RA[n] pin A negative edge was detected on the RA[n] pin No change was detected, or the user cleared the detected change Note: 1. IOCAF0 and IOCAF1 are not available for use if the debugger is enabled. 2. If MCLRE = 1 or LVP = 1, port functionality is disabled and IOCAF3 is not available. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 246 PIC16(L)F18424/44 Interrupt-on-Change 17.6.4 IOCBP Name: Offset: IOCBP 0x1F48 Interrupt-on-Change Positive Edge Register Bit Access Reset 7 6 5 4 IOCBP7 IOCBP6 IOCBP5 IOCBP4 R/W R/W R/W R/W 0 0 0 0 3 2 1 0 Bits 4, 5, 6, 7 - IOCBPn Interrupt-on-Change Positive Edge Enable bits Value 1 0 Description Interrupt-on-Change enabled on the IOCB pin for a positive-going edge. Associated Status bit and interrupt flag will be set upon detecting an edge. Interrupt-on-Change disabled for the associated pin. Note: PORTB associated registers are available on 20-pin or higher pin count devices only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 247 PIC16(L)F18424/44 Interrupt-on-Change 17.6.5 IOCBN Name: Offset: IOCBN 0x1F49 Interrupt-on-Change Negative Edge Register Bit Access Reset 7 6 5 4 IOCBN7 IOCBN6 IOCBN5 IOCBN4 R/W R/W R/W R/W 0 0 0 0 3 2 1 0 Bits 4, 5, 6, 7 - IOCBNn Interrupt-on-Change Negative Edge Enable bits Value 1 0 Description Interrupt-on-Change enabled on the IOCB pin for a negative-going edge. Associated Status bit and interrupt flag will be set upon detecting an edge. Interrupt-on-Change disabled for the associated pin Note: PORTB associated registers are available on 20-pin or higher pin count devices only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 248 PIC16(L)F18424/44 Interrupt-on-Change 17.6.6 IOCBF Name: Offset: IOCBF 0x1F4A PORTB Interrupt-on-Change Flag Register Bit Access Reset 7 6 5 4 IOCBF7 IOCBF6 IOCBF5 IOCBF4 R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 3 2 1 0 Bits 4, 5, 6, 7 - IOCBFn Interrupt-on-Change Flag bits Value 1 1 0 Condition IOCBP[n]=1 IOCBN[n]=1 IOCBP[n]=x and IOCBN[n]=x Description A positive edge was detected on the RB[n] pin A negative edge was detected on the RB[n] pin No change was detected, or the user cleared the detected change Note: PORTB associated registers are available on 20-pin or higher pin count devices only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 249 PIC16(L)F18424/44 Interrupt-on-Change 17.6.7 IOCCP Name: Offset: IOCCP 0x1F53 Interrupt-on-Change Positive Edge Register Bit Access Reset 7 6 5 4 3 2 1 0 IOCCP7 IOCCP6 IOCCP5 IOCCP4 IOCCP3 IOCCP2 IOCCP1 IOCCP0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5, 6, 7 - IOCCPn Interrupt-on-Change Positive Edge Enable bits Value 1 0 Description Interrupt-on-Change enabled on the IOCC pin for a positive-going edge. Associated Status bit and interrupt flag will be set upon detecting an edge. Interrupt-on-Change disabled for the associated pin. Note: IOCCP6 and IOCCP7 are available on 20-pin or higher pin count devices only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 250 PIC16(L)F18424/44 Interrupt-on-Change 17.6.8 IOCCN Name: Offset: IOCCN 0x1F54 Interrupt-on-Change Negative Edge Register Bit Access Reset 7 6 5 4 3 2 1 0 IOCCN7 IOCCN6 IOCCN5 IOCCN4 IOCCN3 IOCCN2 IOCCN1 IOCCN0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5, 6, 7 - IOCCNn Interrupt-on-Change Negative Edge Enable bits Value 1 0 Description Interrupt-on-Change enabled on the IOCC pin for a negative-going edge. Associated Status bit and interrupt flag will be set upon detecting an edge. Interrupt-on-Change disabled for the associated pin Note: IOCCN6 and IOCCN7 are available on 20-pin or higher pin count devices only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 251 PIC16(L)F18424/44 Interrupt-on-Change 17.6.9 IOCCF Name: Offset: IOCCF 0x1F55 PORTC Interrupt-on-Change Flag Register Bit Access Reset 7 6 5 4 3 2 1 0 IOCCF7 IOCCF6 IOCCF5 IOCCF4 IOCCF3 IOCCF2 IOCCF1 IOCCF0 R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS R/W/HS 0 0 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5, 6, 7 - IOCCFn Interrupt-on-Change Flag bits Value 1 1 0 Condition IOCCP[n]=1 IOCCN[n]=1 IOCCP[n]=x and IOCCN[n]=x Description A positive edge was detected on the RC[n] pin A negative edge was detected on the RC[n] pin No change was detected, or the user cleared the detected change Note: IOCCF6 and IOCCF7 are available on 20-pin or higher pin count devices only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 252 PIC16(L)F18424/44 (FVR) Fixed Voltage Reference 18. (FVR) Fixed Voltage Reference The Fixed Voltage Reference, or FVR, is a stable voltage reference, independent of VDD, with the following selectable output levels: * 1.024V * 2.048V * 4.096V The output of the FVR can be configured to supply a reference voltage to the following: * * * * ADC input channel ADC positive reference Comparator input Digital-to-Analog Converter (DAC) The FVR can be enabled by setting the FVREN bit of the FVRCON register. Important: Fixed Voltage Reference output cannot exceed VDD. Related Links FVRCON 18.1 Independent Gain Amplifiers The output of the FVR, which is connected to the ADC, Comparators, and DAC, is routed through two independent programmable gain amplifiers. Each amplifier can be programmed for a gain of 1x, 2x or 4x, to produce the three possible voltage levels. The ADFVR<1:0> bits of the FVRCON register are used to enable and configure the gain amplifier settings for the reference supplied to the ADC module. Reference the ADC chapter for additional information. The CDAFVR<1:0> bits of the FVRCON register are used to enable and configure the gain amplifier settings for the reference supplied to the DAC and comparator module. Related Links (ADC2) Analog-to-Digital Converter with Computation Module (CMP) Comparator Module (DAC) 5-Bit Digital-to-Analog Converter Module 18.2 FVR Stabilization Period When the Fixed Voltage Reference module is enabled, it requires time for the reference and amplifier circuits to stabilize. Once the circuits stabilize and are ready for use, the FVRRDY bit of the FVRCON register will be set. FVRRDY is an indicator of the reference being ready. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 253 Filename: Title: Last Edit: First Used: Note: 10-000053D.vsd VOLTAGE REFERENCE BLOCK DIAGRAM (ADC, Comp and DAC) 9/15/2016 PIC16F1613 (LECQ) 1. Any peripheral requiring the Fixed Reference (See Table 13-1) 2. FVRRDY is always `1' for PIC16(L)F15354/55 devices only. PIC16(L)F18424/44 (FVR) Fixed Voltage Reference Figure 18-1. Voltage Reference Block Diagram Rev. 10-000053D 9/15/2016 ADFVR<1:0> CDAFVR<1:0> 2 1x 2x 4x ADC FVR Buffer 1x 2x 4x Comparator and DAC FVR Buffer 2 FVREN Voltage Reference FVRRDY (Note 1) Note: 1. In the case of an F device, or a device on which the BOR is enabled in the Configuration Word settings, then the FVRRDY bit will be high prior to setting FVREN as those modules require the reference voltage. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 254 PIC16(L)F18424/44 (FVR) Fixed Voltage Reference 18.3 Register Summary - FVR Offset Name Bit Pos. 0x090C FVRCON 7:0 18.4 FVREN FVRRDY TSEN TSRNG CDAFVR[1:0] ADFVR[1:0] Register Definitions: FVR Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 255 PIC16(L)F18424/44 (FVR) Fixed Voltage Reference 18.4.1 FVRCON Name: Offset: FVRCON 0x90C Fixed Voltage Reference Control Register Bit Access Reset 7 6 5 4 FVREN FVRRDY TSEN TSRNG 3 2 1 R/W R R/W R/W R/W R/W R/W R/W 0 q 0 0 0 0 0 0 CDAFVR[1:0] 0 ADFVR[1:0] Bit 7 - FVREN Fixed Voltage Reference Enable bit Value 1 0 Description Fixed Voltage Reference is enabled Fixed Voltage Reference is disabled Bit 6 - FVRRDY Fixed Voltage Reference Ready Flag bit Value 1 0 Description Fixed Voltage Reference output is ready for use Fixed Voltage Reference output is not ready or not enabled Bit 5 - TSEN Temperature Indicator Enable bit(2) Value 1 0 Description Temperature Indicator is enabled Temperature Indicator is disabled Bit 4 - TSRNG Temperature Indicator Range Selection bit(2) Value 1 0 Description VOUT = VDD - 4Vt (High Range) VOUT = VDD - 2Vt (Low Range) Bits 3:2 - CDAFVR[1:0] Comparator FVR Buffer Gain Selection bits Value 11 10 01 00 Description Comparator FVR Buffer Gain is 4x, (4.096V)(1) Comparator FVR Buffer Gain is 2x, (2.048V)(1) Comparator FVR Buffer Gain is 1x, (1.024V) Comparator FVR Buffer is off Bits 1:0 - ADFVR[1:0] ADC FVR Buffer Gain Selection bit Value 11 10 Description ADC FVR Buffer Gain is 4x, (4.096V)(1) ADC FVR Buffer Gain is 2x, (2.048V)(1) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 256 PIC16(L)F18424/44 (FVR) Fixed Voltage Reference Value 01 00 Description ADC FVR Buffer Gain is 1x, (1.024V) ADC FVR Buffer is off Note: 1. Fixed Voltage Reference output cannot exceed VDD. 2. See Temperature Indicator Module section for additional information. Related Links Temperature Indicator Module (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 257 PIC16(L)F18424/44 Temperature Indicator Module 19. Temperature Indicator Module This family of devices is equipped with a temperature circuit designed to measure the operating temperature of the silicon die. The main purpose of the temperature indicator module is to provide a temperature-dependent voltage that can be measured by the Analog-to-Digital Converter. The circuit's range of operating temperature falls between -40C and +125C. The circuit may be used as a temperature threshold detector or a more accurate temperature indicator, depending on the level of calibration performed. A one-point calibration allows the circuit to indicate a temperature closely surrounding that point. A two-point calibration allows the circuit to sense the entire range of temperature more accurately. 19.1 Module Operation The temperature indicator module consists of a temperature-sensing circuit that provides a voltage to the Filename:V 10-000069D.vsd device ADC. The analog voltage output, MEAS, varies inversely to the device temperature. The output of Title: TEMPERATURE CIRCUIT DIAGRAM the temperature indicator is referred as VMEAS.11/13/2017 Lastto Edit: First Used: PIC18(L)F2x/4xK42 The following figure shows a simplified Note: block diagram of the temperature indicator module. Figure 19-1. Temperature Indicator Module Block Diagram Rev. 10-000069D 11/13/2017 VDD TSRNG TSEN Temperature Indicator Module VMEAS To ADC GND The output of the circuit is measured using the internal Analog-to-Digital Converter. A channel is reserved for the temperature circuit output. Refer to the ADC link below for detailed information. The ON/OFF bit for the module is located in the FVRCON register. The circuit is enabled by setting the TSEN bit of the FVRCON register. When the module is disabled, the circuit draws no current. Refer to the FVR link below for more information. The circuit operates in either High or Low range. Refer to the "Temperature Indicator Range" for more details on the range settings. Related Links (FVR) Fixed Voltage Reference Temperature Indicator Range (ADC2) Analog-to-Digital Converter with Computation Module (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 258 PIC16(L)F18424/44 Temperature Indicator Module 19.2 Minimum Operating VDD When the temperature circuit is operated in Low range, the device may be operated at any operating voltage that is within specifications. When the temperature circuit is operated in High range, the device operating voltage, VDD, must be high enough to ensure that the temperature circuit is correctly biased. The following table shows the recommended minimum VDD vs. Range setting. Table 19-1. Recommended VDD vs. Range 19.3 Min. VDD, TSRNG = 1 (High Range) Min. VDD, TSRNG = 0 (Low Range) 2.5V 1.8V Temperature Indicator Range The temperature indicator circuit operates in either High or Low range. The High range, selected by setting the TSRNG bit of the FVRCON register, provides a wider output voltage. This provides more resolution over the temperature range. High range requires a higher-bias voltage to operate and thus, a higher VDD is needed. The Low range is selected by clearing the TSRNG bit of the FVRCON register. The Low range generates a lower sensor voltage and thus, a lower VDD voltage is needed to operate the circuit. The output voltage of the sensor is the highest value at -40C and the lowest value at +125C. * High Range: The High range is used in applications with the reference for the ADC, VREF = 2.048V. This range may not be suitable for battery-powered applications. The ADC reading (in counts) at 90C for the high range setting is stored in the DIA Table as parameter TSHR2. * Low Range: This mode is useful in applications in which the VDD is too low for high-range operation. The VDD in this mode can be as low as 1.8V. VDD must, however, be at least 0.5V higher than the maximum sensor voltage depending on the expected low operating temperature. The ADC reading (in counts) at 90C for the low range setting is stored in the DIA Table as parameter TSLR2. 19.4 Estimation of Temperature This section describes the steps involved in estimating the die temperature, TMEAS: 1. Obtain the ADC count value of the measured analog voltage: The analog output voltage, VMEAS is converted to a digital count value by the Analog-to-Digital Converter (ADC) and is referred to as ADCMEAS. 2. Obtain the ADC count value, ADCDIA at 90C, from the DIA Table. This parameter is TSLR2 for the low range setting or TSHR2 for the high range setting of the temperature indicator module. 3. Obtain the output analog voltage (in mV) value of the Fixed Reference Voltage (FVR) for 2x setting, from the DIA table. This parameter is referred to as FVRA2X in the DIA Table. 4. Obtain the value of the temperature indicator voltage sensitivity, parameter Mv, from the "Electrical Specifications" section . The following equation provides an estimate of the die temperature based on the above parameters: Equation 19-1. Sensor Temperature - x 2 = 90 + 2 - 1 x (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 259 PIC16(L)F18424/44 Temperature Indicator Module Note: Where: ADCMEAS = ADC reading at temperature being estimated ADCDIA = ADC reading stored in the DIA FVRA2X = FVR value stored in the DIA for 2x setting N = Resolution of the ADC Mv = Temperature Indicator voltage sensitivity (mV/C) Note: It is recommended to take the average of ten measurements of ADCMEAS to reduce noise and improve accuracy. Related Links Temperature Indicator Requirements 19.4.1 Calibration 19.4.1.1 Higher-Order Calibration If the application requires more precise temperature measurement, additional calibrations steps will be necessary. For these applications, two-point or three-point calibration is recommended. An Application Note will be released in future that demonstrates higher-order calibration process. An Application Note will be released in future that demonstrates higher-order calibration process. 19.4.2 Temperature Resolution The resolution of the ADC reading, Ma (C/count), depends on both the ADC resolution N and the reference voltage used for conversion, as shown in the equation below. It is recommended to use the smallest VREF value, such as the ADC FVR1 Output Voltage for 2x setting (FVRA2X) value from the DIA Table. Related Links Fixed Voltage Reference (FVR) Specifications 19.5 ADC Acquisition Time To ensure accurate temperature measurements, the user must wait a minimum of 25 s for the ADC value to settle, after the ADC input multiplexer is connected to the temperature indicator output, before the conversion is performed. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 260 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20. (ADC2) Analog-to-Digital Converter with Computation Module The Analog-to-Digital Converter with Computation (ADC2) allows conversion of an analog input signal to a 12-bit binary representation of that signal. This device uses analog inputs, which are multiplexed into a single sample and hold circuit. The output of the sample and hold is connected to the input of the converter. The converter generates a 12-bit binary result via successive approximation and stores the conversion result into the ADC result registers (ADRESH:ADRESL register pair). Additionally, the following features are provided within the ADC module: * * * * 13-bit Acquisition Timer Hardware Capacitive Voltage Divider (CVD) Support: - 13-bit precharge timer - Adjustable sample and hold capacitor array - Guard ring digital output drive Automatic Repeat and Sequencing: - Automated double sample conversion for CVD - Two sets of result registers (Result and Previous result) - Auto-conversion trigger - Internal retrigger Computation Features: - Averaging and low-pass filter functions - Reference comparison - 2-level threshold comparison - Selectable interrupts The figure below shows the block diagram of the ADC. The ADC voltage reference is software selectable to be either internally generated or externally supplied. The ADC can generate an interrupt upon completion of a conversion and upon threshold comparison. These interrupts can be used to wake-up the device from Sleep. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 261 PIC16(L)F18424/44 Filename: Title: Last Edit: Figure First 20-1. Used: 10-000034D.vsd 12-bit ADC Block Diagram 11/2/2016 ADC2PIC18F24/25K42 Block Diagram (MVAD) (ADC2) Analog-to-Digital Converter with Comp... PREF<1:0> FVR_buffer1 VREF+ pin 11 Reserved 01 Rev. 10-000034D 11/2/2016 Positive Reference Select 10 00 VDD NREF VREF- pin 1 0 External Channel Inputs ANa Vref- . . . ANz VSS Internal Channel Inputs CS VSS AN0 Vref+ ADC_clk sampled input ADC Clock Select FOSC /n Fosc Divider FRC FOSC FRC Temp Indicator DACx_output FVR_buffer ADC CLOCK SOURCE ADC Sample Circuit PCH<5:0> ADFM set bit ADIF 12 complete Write to bit GO/DONE 12-bit Result GO/DONE 16 start Enable ADRESH ADRESL Trigger Select ACT<4:0> ADON . . . VSS Trigger Sources AUTO CONVERSION TRIGGER 20.1 ADC Configuration When configuring and using the ADC the following functions must be considered: * * * * * * * * Port Configuration Channel Selection ADC Voltage Reference Selection ADC Conversion Clock Source Interrupt Control Result Formatting Conversion Trigger Selection ADC Acquisition Time (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 262 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... * * * * 20.1.1 ADC Precharge Time Additional Sample and Hold Capacitor Single/Double Sample Conversion Guard Ring Outputs Port Configuration The ADC can be used to convert both analog and digital signals. When converting analog signals, the I/O pin should be configured for analog by setting the associated TRIS and ANSEL bits. Refer to the "I/O Ports" section for more information. Important: Analog voltages on any pin that is defined as a digital input may cause the input buffer to conduct excess current. Related Links I/O Ports 20.1.2 Channel Selection The ADPCH register determines which channel is connected to the sample and hold circuit. When changing channels, a delay is required before starting the next conversion. There are several channel selections available, as shown in the following table: Table 20-1. ADC Positive Input Channel Selections PCH ADC Positive Channel Input 111111 Fixed Voltage Reference (FVR) 2 111110 Fixed Voltage Reference (FVR) 1 111101 DAC1 output 111100 Temperature Indicator 111011 AVSS (Analog Ground) 111010-011000 Reserved. No channel connected. 010111 RC7/ANC7 010110 RC6/ANC6 010101 RC5/ ANC5 010100 RC4/ ANC4 010011 RC3/ANC3 010010 RC2/ANC2 010001 RC1/ ANC1 010000 RC0/ANC0 001111 RB7/ANB7 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 263 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... PCH ADC Positive Channel Input 001110 RB6/ANB6 001101 RB5/ANB5 001100 RB4/ ANB4 001011 RB3/ANB3 001010 RB2/ ANB2 001001 RB1/ ANB1 001000 RB0/ANB0 000111 RA7/ANA7 000110 RA6/ANA6 000101 RA5/ANA5 000100 RA4/ ANA4 000011 Reserved. No channel connected. 000010 RA2/ ANA2 000001 RA1/ ANA1 000000 RA0/ANA0 Related Links ADC Operation (FVR) Fixed Voltage Reference Temperature Indicator Module (DAC) 5-Bit Digital-to-Analog Converter Module 20.1.3 ADC Voltage Reference The PREF bits provide control of the positive voltage reference. The positive voltage reference can be: * * * * * VREF+ pin VDD FVR 1.024V FVR 2.048V FVR 4.096V The NREF bit provides control of the negative voltage reference. The negative voltage reference can be: * * VREF- pin VSS Related Links (FVR) Fixed Voltage Reference ADREF (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 264 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.1.4 Conversion Clock The source of the conversion clock is software selectable via the ADCLK register and the CS bit. If FOSC is selected as the ADC clock, there is a prescaler available to divide the clock so that it meets the ADC clock period specification. The ADC clock source options are the following: * * FOSC/2*n (where `n' is from 1 to 128) FRC (dedicated RC oscillator) The Filename: time to complete one bit conversion is defined as the TAD. The following figure shows the complete 10-000035C.vsd Title: Conversion Tad Cycles timing details of theAnalog-to-Digital ADC conversion. Last Edit: 11/2/2016 First 20-2. Used: Analog-to-Digital PIC18F24/25K42 Conversion TAD Cycles Figure Precharge Time 1-8191 TCY (TPRE) Rev. 10-000035C 11/2/2016 Acquisition/ Sharing Time 1-8191 TCY (TACQ) Conversion Time (Traditional Timing of ADC Conversion) TCY TCY-TAD TAD 1 TAD 2 TAD 3 TAD 4 TAD 5 TAD 6 TAD 7 TAD 8 TAD 9 TAD 10 TAD 11TAD 12 TAD 13 2TCY b11 b10 b9 External and Internal External and Internal Channels are Channels share charged/discharged charge If ADPRE 0 If ADACQ 0 b8 b7 b6 b5 b4 b3 b2 b1 b0 TAD 11 Conversion starts Holding capacitor CHOLD is disconnected from analog input (typically 100ns) If ADPRE = 0 If ADACQ = 0 (Traditional Operation Start) Set GO bit On the following cycle: ADRESH:ADRESL is loaded, GO bit is cleared, ADIF bit is set, For correct conversion, the appropriate TAD specification must be met. Access the "ADC Timing Specifications" link at the end of this topic for more information. The following table below gives examples of appropriate ADC clock selections. Important: 1. Unless using the FRC, any changes in the system clock frequency will change the ADC clock frequency, which may adversely affect the ADC result. 2. The internal control logic of the ADC runs off of the clock selected by the CS bit. What this can mean is when the CS is set to `1' (ADC runs on FRC), there may be unexpected delays in operation when setting ADC control bits. Table 20-2. ADC Clock Period (TAD) Vs. Device Operating Frequencies(1,4) ADC Clock Period (TAD) ADC Clock Source FOSC/2 FOSC/4 Device Frequency (FOSC) ADCLK 64 MHz 32 MHz 000000 31.25 ns(2) 62.5 ns(2) 000001 62.5 ns(2) (c) 2018 Microchip Technology Inc. 20 MHz 16 MHz 8 MHz 4 MHz 100 ns(2) 125 ns(2) 250 ns(2) 500 ns(2) 125 ns(2) 200 ns(2) 250 ns(2) 500 ns(2) Datasheet Preliminary 1.0 s 1 MHz 2.0 s 4.0 s DS40002000A-page 265 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... ADC Clock Period (TAD) Device Frequency (FOSC) ADC Clock Source ADCLK 64 MHz 32 MHz FOSC/6 000010 93.75 ns(2) 187.5 ns(2) FOSC/8 000011 ... FOSC/16 ... 000100 20 MHz 16 MHz 4 MHz 1 MHz 1.5 s 6.0 s 1.0 s 2.0 s 8.0 s ... ... ... ... 1.0 s 2.0 s 4.0 s 16.0 s(3) 300 ns(2) 375 ns(2) 750 ns(2) 125 ns(2) 250 ns(2) 400 ns(2) 500 ns(2) ... ... 8 MHz ... 250 ns(2) 500 ns(2) 800 ns(2) ... ... ... ... ... ... ... ... ... FOSC/128 111111 2.0 s 4.0 s 6.4 s 8.0 s 16.0 s(3) 32.0 s(2) 128.0 s(2) CS(ADCON0<4>) =1 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s 1.0-6.0 s FRC Note: 1. See TAD parameter in the "Electrical Specifications" section for FRC source typical TAD value. 2. These values violate the required TAD time. 3. Outside the recommended TAD time. 4. The ADC clock period (TAD) and total ADC conversion time can be minimized when the ADC clock is derived from the system clock FOSC. However, the FRC oscillator source must be used when conversions are to be performed with the device in Sleep mode. Related Links ADCON0 Analog-to-Digital Converter (ADC) Conversion Timing Specifications 20.1.5 Interrupts The ADC module allows for the ability to generate an interrupt upon completion of an Analog-to-Digital Conversion. The ADC Interrupt Flag is the ADIF bit in the PIRx register. The ADC Interrupt Enable is the ADIE bit in the PIEx register. The ADIF bit must be cleared in software. Important: 1. The ADIF bit is set at the completion of every conversion, regardless of whether or not the ADC interrupt is enabled. 2. The ADC operates during Sleep only when the FRC oscillator is selected. This interrupt can be generated while the device is operating or while in Sleep. If the device is in Sleep, the interrupt will wake-up the device. Upon waking from Sleep, the next instruction following the SLEEP instruction is always executed. If the user is attempting to wake-up from Sleep and resume in-line code execution, the ADIE bit and the PEIE bit of the INTCON register must both be set and the GIE bit of the (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 266 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... INTCON register must be cleared. If all three of these bits are set, the execution will switch to the Interrupt Service Routine. 20.1.6 Result Formatting The 12-bit ADC conversion result can be supplied in two formats, left justified or right justified. The FRM bit controls the output format. The figure below shows the two output formats. Writes to the ADRES register pair are always right justified regardless of the selected format mode. Therefore, data read after writing to ADRES when FRM = 0 will be shifted left four places. Figure 20-3. 12-Bit ADC Conversion Result Format Rev. 30-000116B 6/27/2017 ADRESH (ADFRM = 0) ADRESL MSB bit 7 bit 0 bit 7 LSB 12-bit ADC Result (ADFRM = 1) Unimplemented: Read as `0' MSB bit 7 Unimplemented: Read as `0' bit 0 LSB bit 0 bit 7 bit 0 12-bit ADC Result 20.2 ADC Operation 20.2.1 Starting a Conversion To enable the ADC module, the ON bit must be set to a `1'. A conversion may be started by any of the following: * Software setting the GO bit to `1' * * An external trigger (source selected by ADACT) A continuous-mode retrigger (see "Continuous Sampling mode" section.) . Important: The GO bit should not be set in the same instruction that turns on the ADC. Related Links ADC Conversion Procedure (Basic Mode) Continuous Sampling Mode ADCON0 ADCON2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 267 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.2.2 Completion of a Conversion When any individual conversion is complete, the value already in ADRES is written into ADPREV (if PSIS = 1) and the new conversion result appears in ADRES. When the conversion completes, the ADC module will: * * * * Clear the GO bit (unless the CONT bit is set) Set the ADIF Interrupt Flag bit Set the MATH bit Update ADACC When DSEN = 0 then after every conversion, or when DSEN = 1 then after every other conversion, the following events occur: * * ADERR is calculated ADTIF interrupt is set if ADERR calculation meets threshold comparison Importantly, filter and threshold computations occur after the conversion itself is complete. As such, interrupt handlers responding to ADIF should check ADTIF before reading filter and threshold results. 20.2.3 Terminating a Conversion If a conversion must be terminated before completion, the GO bit can be cleared in software. The ADRESH and ADRESL registers will be updated with the partially complete Analog-to-Digital conversion sample. Incomplete bits will match the last bit converted. In this case, filter and/or threshold occur. Important: A device Reset forces all registers to their Reset state. Thus, the ADC module is turned off and any pending conversion is terminated. 20.2.4 ADC Operation During Sleep The ADC module can operate during Sleep. This requires the ADC clock source to be set to the ADCRC option. When the ADCRC oscillator source is selected, the ADC waits one additional instruction before starting the conversion. This allows the SLEEP instruction to be executed, which can reduce system noise during the conversion. If the ADC interrupt is enabled, the device will wake-up from Sleep when the conversion completes. If the ADC interrupt is disabled, the ADC module is turned off after the conversion completes, although the ON bit remains set. 20.2.5 External Trigger During Sleep If the external trigger is received during sleep while the ADC clock source is set to the FRC, the ADC module will perform the conversion and set the ADIF bit upon completion. If an external trigger is received when the ADC clock source is something other than FRC, the trigger will be recorded, but the conversion will not begin until the device exits Sleep. 20.2.6 Auto-Conversion Trigger The auto-conversion trigger allows periodic ADC measurements without software intervention. When a rising edge of the selected source occurs, the GO bit is set by hardware. The auto-conversion trigger source is selected by the ACT bits. Using the Auto-conversion Trigger does not assure proper ADC timing. It is the user's responsibility to ensure that the ADC timing requirements are met. See the following table for auto-conversion sources. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 268 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... Table 20-3. ADC Auto-Conversion Trigger Sources 20.2.7 ACT Auto-conversion Trigger Source 11111 Software write to ADPCH 11110 Reserved, do not use 11101 Software read of ADRESH 11100 Software read of ADERRH 11011 to 11000 Reserved, do not use 10111 CLC4_out 10110 CLC3_out 10101 CLC2_out 10100 CLC1_out 10011 Logical OR of all Interrupt-on-change Interrupt Flags 10010 C2_out 10001 C1_out 10000 NCO1_out 01111 PWM7_out 01110 PWM6_out 01101 CCP4_trigger 01100 CCP3_trigger 01011 CCP2_trigger 01010 CCP1_trigger 01001 SMT1_trigger 01000 TMR6_postscaled 00111 TMR5_overflow 00110 TMR4_postscaled 00101 TMR3_overflow 00100 TMR2_postscaled 00011 TMR1_overflow 00010 TMR0_overflow 00001 Pin selected by ADACTPPS 00000 External Trigger Disabled ADC Conversion Procedure (Basic Mode) This is an example procedure for using the ADC to perform an Analog-to-Digital conversion: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 269 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 1. 2. 3. 4. 5. 6. 7. 8. Configure Port: 1.1. Disable pin output driver (Refer to the TRISx register) 1.2. Configure pin as analog (Refer to the ANSELx register) Configure the ADC module: 2.1. Select ADC conversion clock 2.2. Configure voltage reference 2.3. Select ADC input channel (precharge+acquisition) 2.4. Turn on ADC module Configure ADC interrupt (optional): 3.1. Clear ADC interrupt flag 3.2. Enable ADC interrupt 3.3. Enable peripheral interrupt (PIE bit) 3.4. Enable global interrupt (GIE bit) (see Note 1 below) If ADACQ = 0, software must wait the required acquisition time (see Note 2 below). Start conversion by setting the GO bit. Wait for ADC conversion to complete by one of the following: 6.1. Polling the GO bit 6.2. Polling the ADIF bit 6.3. Waiting for the ADC interrupt (interrupts enabled) Read ADC Result. Clear the ADC interrupt flag (required if interrupt is enabled). Important: 1. The global interrupt can be disabled if the user is attempting to wake-up from Sleep and resume in-line code execution. 2. Refer to the "ADC Acquisition Requirements" section. ADC Conversion (assembly) ; This code block configures the ADC for polling, Vdd and Vss references, ; FRC oscillator, and AN0 input. ; Conversion start & polling for completion are included. ; BANKSEL ADCON1 ; movlw B'11110000' ;Right justify, FRC oscillator movwf ADCON1 ;Vdd and Vss Vref BANKSEL TRISA ; bsf TRISA,0 ;Set RA0 to input BANKSEL ANSEL ; bsf ANSEL,0 ;Set RA0 to analog BANKSEL ADCON0 ; movlw B'00000001' ;Select channel AN0 movwf ADCON0 ;Turn ADC On call SampleTime ;Acquisiton delay bsf ADCON0,ADGO ;Start conversion btfsc ADCON0,ADGO ;Is conversion done? goto $-1 ;No, test again BANKSEL ADRESH ; movf ADRESH,W ;Read upper 2 bits movwf RESULTHI ;store in GPR space movf ADRESL,W ;Read lower 8 bits movwf RESULTLO ;Store in GPR space (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 270 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... ADC Conversion (C) /*This code block configures the ADC for polling, VDD and VSS references, ADCRC oscillator and AN0 input. Conversion start & polling for completion are included. */ void main() { //System Initialize initializeSystem(); //Setup ADC ADCON0bits.FM = 1; ADCON0bits.CS = 1; ADPCH = 0x00; TRISAbits.TRISA0 = 1; ANSELAbits.ANSELA0 = 1; ADCON0bits.ON = 1; while (1) { ADCON0bits.GO = 1; while (ADCON0bits.GO); resultHigh = ADRESH; resultLow = ADRESL; } } //right justify //FRC Clock //RA0 is Analog channel //Set RA0 to input //Set RA0 to analog //Turn ADC On //Start conversion //Wait for conversion done //Read result //Read result Related Links ADC Acquisition Requirements 20.3 ADC Acquisition Requirements For the ADC to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The Analog Input model is shown in the following figure. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), refer to the following figure. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 271 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... Figure 20-4. Analog Input Model Rev. 30-000114B 6/27/2017 Rs VA VDD Analog Input pin VT 0.6V CPIN 5 pF VT 0.6V RIC 1k Sampling Switch SS Rss I LEAKAGE(1) CHOLD = 28 pF Ref- Legend: CHOLD CPIN = Sample/Hold Capacitance = Input Capacitance 6V 5V VDD 4V 3V 2V I LEAKAGE = Leakage current at the pin due to various junctions = Interconnect Resistance RIC = Resistance of Sampling Switch RSS SS = Sampling Switch VT = Threshold Voltage RSS 5 6 7 8 9 10 11 Sampling Switch (kOhm) Note: 1. Refer to "I/O Ports Electrical Specifications". Important: The maximum recommended impedance for analog sources is 10 k. If the source impedance is decreased, the acquisition time may be decreased. After the analog input channel is selected (or changed), an ADC acquisition must be completed before the conversion can be started. To calculate the minimum acquisition time, the following equation may be used. This equation assumes that 1/2 LSb error is used (4,096 steps for the ADC). The 1/2 LSb error is the maximum error allowed for the ADC to meet its specified resolution. Equation 20-1. Acquisition Time Example Assumptions: Temperature = 50C and external impedance pf 10 k 5.0V VDD TACQ = Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient = TAMP + TC + TCOFF = 2 s + TC + [(Temperature - 25C)(0.05 s/C)] The value for TC can be approximated with the following equations: 1 - 1 - 2 1 +1 - -1 = = (c) 2018 Microchip Technology Inc. ;[1]charged to within 1/2 lsb ;[2]charge response to Datasheet Preliminary DS40002000A-page 272 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 1 - - = 1 - 1 +1 2 ;combining [1] and [2] -1 Note: Where n = number of bits of the ADC. Solving for TC: = - + + ln 1/8191 = - 28 1 + 7 + 10 ln 0.0001221 = 4.54 Therefore: = 2 + 4.54 + 50 - 25 0.05/ = 7.79 Note: 1. The reference voltage (VREF) has no effect on the equation, since it cancels itself out. 2. The charge holding capacitor (CHOLD) is not discharged after each conversion. 3. The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin leakage specification. Figure 20-6. ADC Transfer Function Rev. 30-000115B 6/27/2017 Full-Scale Range FFFh FFEh ADC Output Code FFDh FFCh FFBh 03h 02h 01h 00h Analog Input Voltage 0.5 LSB REF- 1.5 LSB Zero-Scale Transition Full-Scale Transition REF+ Related Links I/O and CLKOUT Timing Specifications (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 273 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.4 ADC Charge Pump The ADC module has a dedicated charge pump which can be controlled through the ADCPCON0 register. The primary purpose of the charge pump is to supply a constant voltage to the gates of transistor devices in the A/D converter, signal and reference input pass-gates, to prevent degradation of transistor performance at low operating voltage. The charge pump can be enabled by setting the CPON bit. Once enabled, the pump will undergo a startup time to stabilize the charge pump output. Once the output stabilizes and is ready for use, the CPRDY bit will be set. Related Links ADCPCON0 20.5 Capacitive Voltage Divider (CVD) Features The ADC module contains several features that allow the user to perform a relative capacitance measurement on any ADC channel using the internal ADC sample and hold capacitance as a reference. This relative capacitance measurement can be used to implement capacitive touch or proximity sensing applications. The following figure shows the basic block diagram of the CVD portion of the ADC module. Figure 20-7. Hardware Capacitive Voltage Divider Block Diagram Rev. 10-000322B 10/4/2017 VDD VDD ADPPOL & Precharge ADPPOL & Precharge Precharge ANx ADC ADPPOL & Precharge ADPPOL & Precharge ANx Multiplexer ADCAP Additional Sample Capacitors 20.5.1 CVD Operation A CVD operation begins with the ADC's internal sample and hold capacitor (CHOLD) being disconnected from the path which connects it to the external capacitive sensor node. While disconnected, CHOLD is precharged to VDD or VSS the sensor node is also charged to VSS or VDD, respectively to the level opposite that of CHOLD. When the precharge phase is complete, the VDD/VSS bias paths for the two nodes are shut off and the paths between CHOLD and the external sensor node is reconnected, at which time the acquisition phase of the CVD operation begins. During acquisition, a capacitive voltage divider is formed between the precharged CHOLD and sensor nodes, which results in a final voltage level setting on CHOLD (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 274 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... which is determined by the capacitances and precharge levels of the two nodes. After acquisition, the ADC converts the voltage level on CHOLD. This process is then repeated with the selected precharge levels inverted for both the CHOLD and the sensor nodes. The waveform for two CVD measurements, which is known as differential CVD measurement, is shown in the following figure. Figure 20-8. Differential CVD Measurement Waveform Rev. 10-000335A 10/2/2017 Precharge Acquire Convert Precharge Acquire Convert External Capacitive Sensor VSS ADC Sample and Hold Capacitor Voltage VDD Second Sample First Sample Time 20.5.2 Precharge Control The Precharge stage is an optional period of time that brings the external channel and internal sample and hold capacitor to known voltage levels. Precharge is enabled by writing a non-zero value to the ADPRE register. This stage is initiated when an ADC conversion begins, either from setting the GO bit, a special event trigger, or a conversion restart from the computation functionality. If the ADPRE register is cleared when an ADC conversion begins, this stage is skipped. During the precharge time, CHOLD is disconnected from the outer portion of the sample path that leads to the external capacitive sensor and is connected to either VDD or VSS, depending on the value of the PPOL bit. At the same time, the port pin logic of the selected analog channel is overridden to drive a digital high or low out, in order to precharge the outer portion of the ADC's sample path, which includes the external sensor. The output polarity of this override is also determined by the PPOL bit. The amount of time that this charging needs is controlled by the ADPRE register. Important: The external charging overrides the TRIS setting of the respective I/O pin. If there is a device attached to this pin, Precharge should not be used. Related Links (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 275 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... ADCON1 ADPRE 20.5.3 Acquisition Control for CVD The Acquisition stage allows time for the voltage on the internal sample and hold capacitor to charge or discharge from the selected analog channel. This acquisition time is controlled by the ADACQ register. If ADPRE = 0, acquisition starts at the beginning of conversion. When ADPRE 0, the acquisition stage begins when precharge ends. At the start of the acquisition stage, the port pin logic of the selected analog channel is overridden to turn off the digital high/low output drivers so they do not affect the final result of the charge averaging. Also, the selected ADC channel is connected to CHOLD. This allows charge averaging to proceed between the precharged channel and the CHOLD capacitor. Important: When ADPRE 0 setting ADACQ to `0' will set a maximum acquisition time (8191 ADC clock cycles). When ADPRE = 0, setting ADACQ to `0' will disable hardware acquisition time control. 20.5.4 Guard Ring Outputs The following figure shows a typical guard ring circuit. CGUARD represents the capacitance of the guard ring trace placed on the PCB board. The user selects values for RA and RB that will create a voltage profile on CGUARD, which will match the selected acquisition channel. The purpose of the guard ring is to generate a signal in phase with the CVD sensing signal to minimize the effects of the parasitic capacitance on sensing electrodes. It also can be used as a mutual drive for mutual capacitive sensing. For more information about active guard and mutual drive, see Application Note AN1478, "mTouchTM Sensing Solution Acquisition Methods Capacitive Voltage Divider". The ADC has two guard ring drive outputs, ADGRDA and ADGRDB. These outputs can be routed through PPS controls to I/O pins (see "Peripheral Pin Select (PPS) Module" for details) and the polarity of these outputs are controlled by the GPOL and IPEN bits. At the start of the first precharge stage, both outputs are set to match the GPOL bit. Once the acquisition stage begins, ADGRDA changes polarity, while ADGRDB remains unchanged. When performing a double sample conversion, setting the IPEN bit causes both guard ring outputs to transition to the opposite polarity of GPOL at the start of the second precharge stage, and ADGRDA toggles again for the second acquisition. For more information on the timing of the guard ring output, refer to the two following figures. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 276 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... Figure 20-9. Differential CVD with Guard Ring Output Waveform Rev. 10-000336A 10/2/2017 Precharge Acquire Convert Precharge Acquire Convert Guard Ring Capacitance VSS External Capacitive Sensor Voltage VDD Second Sample First Sample Time ADGRDA ADGRDB Related Links ADCON1 (PPS) Peripheral Pin Select Module 20.5.5 Additional Sample and Hold Capacitance Additional capacitance can be added in parallel with the internal sample and hold capacitor (CHOLD) by using the ADCAP register. This register selects a digitally programmable capacitance which is added to the ADC conversion bus, increasing the effective internal capacitance of the sample and hold capacitor in the ADC module. This is used to improve the match between internal and external capacitance for a better sensing performance. The additional capacitance does not affect analog performance of the ADC because it is not connected during conversion. Related Links Computation Operation ADCAP (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 277 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.6 Computation Operation The ADC module hardware is equipped with post conversion computation features. These features provide data post-processing functions that can be applied to the ADC conversion result, including digital filtering/averaging and threshold comparison functions. Figure 20-10. Computational Features Simplified Block Diagram Rev. 10-000260B 8/4/2015 ADCALC<2:0> ADMD<2:0> ADRES ADFILT Average/ Filter 1 0 Error Calculation ADERR Set Interrupt Flag Threshold Logic ADPREV ADSTPT ADPSIS ADUTHR ADLTHR The operation of the ADC computational features is controlled by MD bits. The module can be operated in one of five modes: * Basic: This is a legacy mode. In this mode, ADC conversion occurs on single (DSEN = 0) or double (DSEN = 1) samples. ADIF is set after all the conversions are complete. * Accumulate: With each trigger, the ADC conversion result is added to accumulator and ADCNT increments. ADIF is set after each conversion. ADTIF is set according to the calculation mode. Average: With each trigger, the ADC conversion result is added to the accumulator. When the ADRPT number of samples have been accumulated, a threshold test is performed. Upon the next trigger, the accumulator is cleared. For the subsequent tests, additional ADRPT samples are required to be accumulated. Burst Average: At the trigger, the accumulator is cleared. The ADC conversion results are then collected repetitively until ADRPT samples are accumulated and finally the threshold is tested. Low-Pass Filter (LPF): With each trigger, the ADC conversion result is sent through a filter. When ADRPT samples have occurred, a threshold test is performed. Every trigger after that, the ADC conversion result is sent through the filter and another threshold test is performed. * * * The five modes are summarized in following table. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 278 Table 20-4. Computation Modes Bit Clear Conditions rotatethispage90 Value after Trigger completion Threshold Operations Value at ADTIF interrupt (c) 2018 Microchip Technology Inc. Mode ADMD ADACC and ADCNT ADACC ADCNT Retrigger Threshold Test Interrupt Basic 0 ADACLR = 1 Unchanged Unchanged No Every Sample If threshold=true Accumulate 1 ADACLR = 1 S + ADACC or If (ADCNT=FF): ADCNT, otherwise: ADCNT+1 No Every Sample If ADACC ADACC/ threshold=true Overflow 2ADCRS count If (ADCNT=FF): ADCNT, otherwise: ADCNT+1 No If If ADACC ADACC/ ADCNT>=ADRPT threshold=true Overflow 2ADCRS count (S2-S1) + ADACC Average 3 ADACLR = 1 or ADCNT>=ADRPT at ADGO or retrigger ADACLR = 1 or ADGO set or retrigger S + ADACC or (S2-S1) + ADACC N/A N/A count Each Each repetition: Repeat while If If ADACC ADACC/ ADRPT repetition: same as Average ADCNT=ADRPT threshold=true Overflow 2ADCRS same as End with Average ADCNT=ADRPT End with sum of all samples Low-pass Filter 4 ADACLR = 1 If (ADCNT=FF): ADCNT, otherwise: ADCNT+1 No If If ADACC Filtered ADCNT>=ADRPT threshold=true Overflow Value count DS40002000A-page 279 (S2S1)+ADACCADACC/ 2ADCRS Note: S1 and S2 are abbreviations for Sample 1 and Sample 2, respectively. When DSEN = 0, S1 = ADRES; When DSEN = 1, S1 = ADPREV and S2 = ADRES. PIC16(L)F18424/44 S+ADACCADACC/ 2ADCRS or (ADC2) Analog-to-Digital Converter with Comp... Datasheet Preliminary Burst Average 2 ADAOV ADFLTR ADCNT PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.6.1 Digital Filter/Average The digital filter/average module consists of an accumulator with data feedback options, and control logic to determine when threshold tests need to be applied. The accumulator is a 16-bit wide register which can be accessed through the ADACCH:ADACCL register pair. Upon each trigger event (the GO bit set or external event trigger), the ADC conversion result is added to the accumulator. If the accumulated result exceeds 2(accumulator_width)-1, the OV Accumulator overflow bit is set. The number of samples to be accumulated is determined by the ADRPT (A/D Repeat Setting) register. Each time a sample is added to the accumulator, the ADCNT register is incremented. Once ADRPT samples are accumulated (ADCNT = ADRPT), an accumulator clear command can be issued by the software by setting the ACLR bit. Setting the ACLR bit will also clear the OV bit, as well as the ADCNT register. The ACLR bit is cleared by the hardware when accumulator clearing action is complete. Important: When ADC is operating from FRC, five FRC clock cycles are required to execute the ADACC clearing operation. The CRS bits control the data shift on the accumulator result, which effectively divides the value in accumulator (ADACCU:ADACCH:ADACCL) register pair. For the Accumulate mode of the digital filter, the shift provides a simple scaling operation. For the Average/Burst Average mode, the shift bits are used to determine the number of logical right shifts to be performed on the accumulated result. For the Low-pass Filter mode, the shift is an integral part of the filter, and determines the cut-off frequency of the filter. The table below shows the -3 dB cut-off frequency in T (radians) and the highest signal attenuation obtained by this filter at nyquist frequency (T = ). Table 20-5. Low-pass Filter -3 dB Cut-off Frequency 20.6.2 CRS T (radians) @ -3 dB Frequency dB @ Fnyquist=1/(2T) 1 0.72 -9.5 2 0.284 -16.9 3 0.134 -23.5 4 0.065 -29.8 5 0.032 -36.0 6 0.016 -42.0 7 0.0078 -48.1 Basic Mode Basic mode (MD = 000) disables all additional computation features. In this mode, no accumulation occurs but threshold error comparison is performed. Double sampling, Continuous mode, and all CVD features are still available, but no features involving the digital filter/average features are used. 20.6.3 Accumulate Mode In Accumulate mode (MD = 001), after every conversion, the ADC result is added to the ADACC register. The ADACC register is right-shifted by the value of the CRS bits. This right-shifted value is copied into the ADFLT register. The Formatting mode does not affect the right-justification of the ADFLT value. Upon (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 280 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... each sample, ADCNT is also incremented, incrementing the number of samples accumulated. After each sample and accumulation, the ADACC value has a threshold comparison performed on it and the ADTIF interrupt may trigger. Related Links Threshold Comparison 20.6.4 Average Mode In Average Mode (MD = 010), the ADACC registers accumulate with each ADC sample, much as in Accumulate mode, and the ADCNT register increments with each sample. The ADFLT register is also updated with the right-shifted value of the ADACC register. The value of the CRS bits govern the number of right shifts. However, in Average mode, the threshold comparison is performed upon ADCNT being greater than or equal to a user-defined ADRPT value. In this mode when ADCNT = 2ADCRS, then the final accumulated value will be divided by number of samples, allowing for a threshold comparison operation on the average of all gathered samples. 20.6.5 Burst Average Mode The Burst Average mode (MD = 011) acts the same as the Average mode in most respects. The one way it differs is that it continuously retriggers ADC sampling until the ADCNT value is greater than or equal to ADRPT, even if Continuous Sampling mode is not enabled. This allows for a threshold comparison on the average of a short burst of ADC samples. Related Links Continuous Sampling Mode 20.6.6 Low-pass Filter Mode The Low-pass Filter mode (MD = 100) acts similarly to the Average mode in how it handles samples (accumulates samples until ADCNT value greater than or equal to ADRPT, then triggers threshold comparison), but instead of a simple average, it performs a low-pass filter operation on all of the samples, reducing the effect of high-frequency noise on the average, then performs a threshold comparison on the results. In this mode, the CRS bits determine the cut-off frequency of the low-pass filter. Related Links Digital Filter/Average Computation Operation 20.6.7 Threshold Comparison At the end of each computation: * * The conversion results are latched and held stable at the end-of-conversion. The error (ADERR) is calculated based on a difference calculation which is selected by the CALC bits. The value can be one of the following calculations (see table below for more details): - The first derivative of single measurements - The CVD result in CVD mode - The current result vs. a setpoint - The current result vs. the filtered/average result - The first derivative of the filtered/average value - Filtered/average value vs. a setpoint (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 281 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... * The result of the calculation (ADERR) is compared to the upper and lower thresholds, ADUTH and ADLTH registers, to set the UTHR and LTHR flag bits. The threshold logic is selected by MD bits. The threshold trigger option can be one of the following: - Never interrupt - Error is less than lower threshold - Error is greater than or equal to lower threshold - Error is between thresholds (inclusive) - Error is outside of thresholds - Error is less than or equal to upper threshold - Error is greater than upper threshold - Always interrupt regardless of threshold test results - If the threshold condition is met, the threshold interrupt flag ADTIF is set. Note: 1. The threshold tests are signed operations. 2. If OV is set, a threshold interrupt is signaled. It is good practice for threshold interrupt handlers to verify the validity of the threshold by checking ADAOV. Table 20-6. ADC Error Calculation Mode Action During 1st Precharge Stage CALC DSEN = 0 Single-Sample Mode DSEN = 1 CVD DoubleSample Mode(1) Application 111 Reserved Reserved Reserved 110 Reserved Reserved Reserved 101 ADLFTR-ADSTPT ADFLTR-ADSTPT Average/filtered value vs. setpoint 100 ADPREV-ADFLTR ADPREV-ADFLTR First derivative of filtered value(3) (negative) 011 Reserved Reserved Reserved 010 ADRES-ADFLTR (ADRES-ADPREV)-ADFLTR Actual result vs. averaged/filtered value 001 ADRES-ADSTPT (ADRES-ADPREV)-ADSTPT Actual result vs. setpoint 000 ADRES-ADPREV ADRES-ADPREV First derivative of single measurement(2) Actual CVD result in CVD mode(2) Note: 1. When PSIS = 0, the value of ADRES-ADPREV) is the value of (S2-S1) from Computation Modes. 20.6.8 2. When PSIS = 0 3. When PSIS = 1. Continuous Sampling Mode Setting the CONT bit automatically retriggers a new conversion cycle after updating the ADACC register. The GO bit remains set and retriggering occurs automatically. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 282 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... If SOI = 1, a threshold interrupt condition will clear GO and the conversions will stop. 20.6.9 Double Sample Conversion Double sampling is enabled by setting the DSEN bit. When this bit is set, two conversions are required before the module will calculate threshold error (each conversion must still be triggered separately). The first conversion will set the MATH bit and update ADACC, but will not calculate ADERR or trigger ADTIF. When the second conversion completes, the first value is transferred to ADPREV (depending on the setting of PSIS) and the value of the second conversion is placed into ADRES. Only upon the completion of the second conversion is ADERR calculated and ADTIF triggered (depending on the value of CALC). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 283 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.7 Register Summary - ADC Control Offset Name 0x8C ADLTH 0x8E ADUTH 0x90 ADERR 0x92 ADSTPT 0x94 ADFLTR 0x96 ADACC Bit Pos. 7:0 LTHL[7:0] 15:8 LTHH[7:0] 7:0 UTHL[7:0] 15:8 UTHH[7:0] 7:0 ADERRL[7:0] 15:8 ERRH[7:0] 7:0 STPTL[7:0] 15:8 STPTH[7:0] 7:0 FLTRL[7:0] 15:8 FLTRH[7:0] 7:0 ACCL[7:0] 15:8 ACCH[7:0] 23:16 ACCU[1:0] 0x99 ADCNT 7:0 0x9A ADRPT 7:0 RPT[7:0] 7:0 PREVL[7:0] 15:8 PREVH[7:0] 0x9B ADPREV 0x9D ADRES 0x9F ADPCH CNT[7:0] 7:0 RESL[7:0] 15:8 RESH[7:0] 7:0 PCH[5:0] 0xA0 ... Reserved 0x010B 0x010C ADACQ 0x010E ADCAP 0x010F ADPRE 7:0 ACQL[7:0] 15:8 ACQH[4:0] 7:0 CAP[4:0] 7:0 PREL[7:0] 15:8 PREH[4:0] 0x0111 ADCON0 7:0 ON CONT 0x0112 ADCON1 7:0 PPOL IPEN 0x0113 ADCON2 7:0 PSIS 0x0114 ADCON3 7:0 0x0115 ADSTAT 7:0 0x0116 ADREF 7:0 0x0117 ADACT 7:0 0x0118 ADCLK 7:0 CS CRS[2:0] UTHR GO DSEN ACLR CALC[2:0] OV FRM GPOL LTHR MD[2:0] SOI MD[2:0] MATH STAT[2:0] NREF PREF[1:0] ACT[4:0] CS[5:0] 0x0119 ... Reserved 0x029E 0x029F ADCPCON0 7:0 CPON (c) 2018 Microchip Technology Inc. CPRDY Datasheet Preliminary DS40002000A-page 284 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.8 Register Definitions: ADC Control Long bit name prefixes for the ADC peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 20-7. ADC Long Bit Name Prefixes Peripheral Bit Name Prefix ADC2 AD Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 285 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.8.1 ADCON0 Name: Offset: ADCON0 0x111 ADC Control Register 0 Bit Access Reset 7 6 ON CONT 5 CS 4 3 FRM 2 1 GO 0 R/W R/W R/W R/W R/W/HC 0 0 0 0 0 Bit 7 - ON ADC Enable bit Value 1 0 Description ADC is enabled ADC is disabled Bit 6 - CONT ADC Continuous Operation Enable bit Value 1 0 Description GO is retriggered upon completion of each conversion trigger until TIF is set (if SOI is set) or until GO is cleared (regardless of the value of SOI) GO is cleared upon completion of each conversion trigger Bit 4 - CS ADC Clock Selection bit Value 1 0 Description Clock supplied from FRC dedicated oscillator Clock supplied by FOSC, divided according to ADCLK register Bit 2 - FRM ADC Results Format/Alignment Selection Value 1 0 Description ADRES and ADPREV data are right-justified ADRES and ADPREV data are left-justified, zero-filled Bit 0 - GO ADC Conversion Status bit(1,2) Value 1 0 Description ADC conversion cycle in progress. Setting this bit starts an ADC conversion cycle. The bit is cleared by hardware as determined by the CONT bit ADC conversion completed/not in progress Note: 1. This bit requires ON bit to be set. 2. If cleared by software while a conversion is in progress, the results of the conversion up to this point will be transferred to ADRES and the state machine will be reset, but the ADIF interrupt flag bit will not be set; filter and threshold operations will not be performed. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 286 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.8.2 ADCON1 Name: Offset: ADCON1 0x112 ADC Control Register 1 Bit Access Reset 7 6 5 PPOL IPEN GPOL 4 3 2 1 DSEN 0 R/W R/W R/W R/W 0 0 0 0 Bit 7 - PPOL Precharge Polarity bit Action During 1st Precharge Stage Value x 1 0 1 0 Condition PRE=0 PRE>0 & ADC input is I/O pin PRE>0 & ADC input is I/O pin PRE>0 & ADC input is internal PRE>0 & ADC input is internal Description Bit has no effect Pin shorted to AVDD Pin shorted to VSS CHOLD Shorted to AVDD CHOLD Shorted to VSS Bit 6 - IPEN A/D Inverted Precharge Enable bit Value x 1 0 Condition Description DSEN = 0 Bit has no effect DSEN = 1 The precharge and guard signals in the second conversion cycle are the opposite polarity of the first cycle DSEN = 1 Both Conversion cycles use the precharge and guards specified by PPOL and GPOL Bit 5 - GPOL Guard Ring Polarity Selection bit Value 1 0 Description ADC guard Ring outputs start as digital high during Precharge stage ADC guard Ring outputs start as digital low during Precharge stage Bit 0 - DSEN Double-Sample Enable bit Value 1 0 Description Two conversions are performed on each trigger. Data from the first conversion appears in PREV One conversion is performed for each trigger (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 287 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.8.3 ADCON2 Name: Offset: ADCON2 0x113 ADC Control Register 2 Bit 7 6 PSIS Access Reset 5 4 CRS[2:0] 3 2 ACLR 1 0 MD[2:0] R/W R/W R/W R/W R/W/HC R/W R/W R/W 0 0 0 0 0 0 0 0 Bit 7 - PSIS ADC Previous Sample Input Select bits Value 1 0 Description FLTR is transferred to PREV at start-of-conversion ADRES is transferred to PREV at start-of-conversion Bits 6:4 - CRS[2:0] ADC Accumulated Calculation Right Shift Select bits Value 0 to 7 0 to 7 x Condition MD = b'100' MD = b'011' to b'001' Description Low-pass filter time constant is 2CRS, filter gain is 1:1 The accumulated value is right-shifted by CRS (divided by 2CRS) (1,2) MD = b'000' to b'001' These bits are ignored Bit 3 - ACLR A/D Accumulator Clear Command bit(3) Value 1 0 Description ACC, AOV and CNT registers are cleared Clearing action is complete (or not started) Bits 2:0 - MD[2:0] ADC Operating Mode Selection bits(4) Value 111-101 100 011 010 001 000 Description Reserved Low-pass Filter mode Burst Average mode Average mode Accumulate mode Basic (Legacy) mode Note: 1. To correctly calculate an average, the number of samples (set in RPT) must be 2CRS. 2. CRS = 3'b111 is a reserved option. 3. 4. This bit is cleared by hardware when the accumulator operation is complete; depending on oscillator selections, the delay may be many instructions. See Computation Modes for full mode descriptions. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 288 PIC16(L)F18424/44 (ADC2) Analog-to-Digital Converter with Comp... 20.8.4 ADCON3 Name: Offset: ADCON3 0x114 ADC Control Register 3 Bit 7 6 5 4 3 CALC[2:0] Access Reset 2 SOI 1 0 MD[2:0] R/W R/W R/W R/W/HC R/W R/W R/W 0 0 0 0 0 0 0 Bits 6:4 - CALC[2:0] ADC Error Calculation Mode Select bits See ADC Error Calculation Mode table for selection details. Bit 3 - SOI ADC Stop-on-Interrupt bit Value 1 0 x Condition Description CONT = 1 GO is cleared when the threshold conditions are met, otherwise the conversion is retriggered CONT = 1 GO is not cleared by hardware, must be cleared by software to stop retriggers CONT = 0 This bit is not used Bits 2:0 - MD[2:0] Threshold Interrupt Mode Select bits Value 111 110 101 100 011 010 001 000 Description Interrupt regardless of threshold test results Interrupt if ERR>UTH Interrupt if ERRUTH Interrupt if ERRUTH Interrupt if ERR>LTH and ERRUTH ERRUTH Bit 5 - LTHR ADC Module Less-than Lower Threshold Flag bit Value 1 0 Description ERR R DAC1PSS R R 32-to-1 MUX R 32 Steps DAC1EN DAC1_output To Peripherals R DAC1OUT (1) R DAC1OE R DAC1NSS VREF- 1 VSS VSOURCE- 0 Note: 1. The unbuffered DACx_output is provided on the DACxOUT pin(s). 21.1 Output Voltage Selection The DAC has 32 voltage level ranges. The 32 levels are set with the DAC1R bits. The DAC output voltage can be determined by using the following equation. Equation 21-1. DAC Output Voltage When EN = 1: _ = + - - 4: 0 25 + - Note: See the DAC1CON0 register for the available VSOURCE+ and VSOURCE- selections. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 310 PIC16(L)F18424/44 (DAC) 5-Bit Digital-to-Analog Converter Modu... 21.2 Ratiometric Output Level The DAC output value is derived using a resistor ladder with each end of the ladder tied to a positive and negative voltage reference input source. If the voltage of either input source fluctuates, a similar fluctuation will result in the DAC output value. The value of the individual resistors within the ladder can be found in the "5-Bit DAC Specifications" table from the "Electrical Specifications" chapter. Related Links 5-Bit DAC Specifications 21.3 DAC Voltage Reference Output The unbuffered DAC voltage can be output to the DACxOUTn pin(s) by setting the respective OEn bit(s). Selecting the DAC reference voltage for output on either DACxOUTn pin automatically overrides the digital output buffer, the weak pull-up and digital input threshold detector functions of that pin. Reading the DACxOUTn pin when it has been configured for DAC reference voltage output will always return a `0'. Important: The unbuffered DAC output (DACxOUTn) is not intended to drive an external load. 21.4 Operation During Sleep When the device wakes up from Sleep through an interrupt or a Windowed Watchdog Timer Time-out, the contents of the DACxCON0 register are not affected. To minimize current consumption in Sleep mode, the voltage reference should be disabled. 21.5 Effects of a Reset A device Reset affects the following: * * * DACx is disabled. DACx output voltage is removed from the DACxOUTn pin(s). The DAC1R range select bits are cleared. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 311 PIC16(L)F18424/44 (DAC) 5-Bit Digital-to-Analog Converter Modu... 21.6 Register Summary - DAC Control Offset Name Bit Pos. 0x090E DAC1CON0 7:0 0x090F DAC1CON1 7:0 21.7 EN OE1 PSS[1:0] NSS DAC1R[4:0] Register Definitions: DAC Control Long bit name prefixes for the DAC are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 21-1. DAC Long Bit Name Prefixes Peripheral Bit Name Prefix DAC DAC Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 312 PIC16(L)F18424/44 (DAC) 5-Bit Digital-to-Analog Converter Modu... 21.7.1 DAC1CON0 Name: Offset: DAC1CON0 0x90E DAC Control Register Bit Access Reset 7 6 5 4 3 2 PSS[1:0] 1 0 EN OE1 NSS R/W R/W R/W R/W R/W 0 0 0 0 0 Bit 7 - EN DAC Enable bit Value 1 0 Description DAC is enabled DAC is disabled Bit 5 - OE1 DAC Voltage Output Enable bit Value 1 0 Description DAC voltage level is output on the DAC1OUT1 pin DAC voltage level is disconnected from the DAC1OUT1 pin Bits 3:2 - PSS[1:0] DAC Positive Source Select bit Value 11 10 01 00 Description Reserved FVR buffer VREF+ AVDD Bit 0 - NSS DAC Negative Source Select bit Value 1 0 Description VREFAVSS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 313 PIC16(L)F18424/44 (DAC) 5-Bit Digital-to-Analog Converter Modu... 21.7.2 DAC1CON1 Name: Offset: DAC1CON1 0x90F DAC Data Register Bit 7 6 5 4 3 2 1 0 DAC1R[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - DAC1R[4:0] Data Input Register for DAC bits (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 314 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22. Numerically Controlled Oscillator (NCO) Module The Numerically Controlled Oscillator (NCO) module is a timer that uses overflow from the addition of an increment value to divide the input frequency. The advantage of the addition method over simple counter driven timer is that the output frequency resolution does not vary with the divider value. The NCO is most useful for application that requires frequency accuracy and fine resolution at a fixed duty cycle. Features of the NCO include: * 20-bit Increment Function * Fixed Duty Cycle mode (FDC) mode * Pulse Frequency (PF) mode * Output Pulse Width Control * Multiple Clock Input Sources * Output10-000028E.vsd polarity Control Filename: Title: Numerically Controlled Oscillator (NCOx) Module Simplified BD * Edit:Interrupt Capability Last 10/12/2016 First Used: PIC18(L)F2x/4xK42 The following figure is a simplified block diagram of the NCO module. Figure 22-1. Numerically Controlled Oscillator Module Simplified Block Diagram NCOxINCU NCOxINCH NCOxINCL 20 (1) INCBUFU INCBUFH 20 Rev. 10-000028E 10/12/2016 INCBUFL 20 1111 NCO_overflow NCOx Clock Sources Adder 20 NCOx_clk See NCOxCLK Register NCOxACCU NCOxACCH NCOxACCL 20 NCO_interrupt 0000 CKS<3:0> 4 set bit NCOxIF Fixed Duty Cycle Mode Circuitry D Q D Q 0 _ 1 Q PFM TRIS bit NCOxOUT POL NCOx_out EN S Q Ripple Counter R Q R Note 1: 3 PWS<2:0> D _ Pulse Frequency Mode Circuitry Q To Peripherals OUT Q1 The increment registers are double-buffered to allow for value changes to be made without first disabling the NCO module. The full increment value is loaded into the buffer registers on the second rising edge of the NCOx_clk signal that occurs immediately after a write to NCOxINCL register. The buffers are not user-accessible and are shown here for reference. Note: 1. The increment registers are double-buffered to allow for value changes to be made without first disabling the NCO module. The full increment value is loaded into the buffer registers on the second rising edge of the NCOx_clk signal that occurs immediately after a write to NCOxINCL register. The buffers are not user-accessible and are shown here for reference. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 315 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.1 NCO Operation The NCO operates by repeatedly adding a fixed value to an accumulator. Additions occur at the input clock rate. The accumulator will overflow with a carry periodically, which is the raw NCO output (NCO_overflow). This effectively reduces the input clock by the ratio of the addition value to the maximum accumulator value. See the following equation. 22.1.1 Equation 22-1. NCO Overflow Frequency x = 220 NCO Clock Sources Clock sources available to the NCO are shown in the following table: Table 22-1. NCO Clock Sources CKS Clock Source 1111-1011 Reserved 1010 CLC4_out 1001 CLC3_out 1000 CLC2_out 0111 CLC1_out 0110 CLKR 0101 SOSC 0100 MFINTOSC (32 kHz) 0011 MFINTOSC (500 kHz) 0010 LFINTOSC 0001 HFINTOSC 0000 FOSC The NCO clock source is selected by configuring the CKS bits. Related Links NCOxCLK 22.1.2 Accumulator The accumulator is a 20-bit register. Read and write access to the accumulator is available through three registers: * NCOxACCL * NCOxACCH * NCOxACCU Related Links NCOxACC (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 316 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.1.3 Adder The NCO Adder is a full adder, which operates synchronously from the source clock. The addition of the previous result and the increment value replaces the accumulator value on the rising edge of each input clock. 22.1.4 Increment Registers The increment value is stored in three registers making up a 20-bit incrementer. In order of LSB to MSB they are: * NCOxINCL * NCOxINCH * NCOxINCU When the NCO module is enabled, the NCOxINCU and NCOxINCH registers should be written first, then the NCOxINCL register. Writing to the NCOxINCL register initiates the increment buffer registers to be loaded simultaneously on the second rising edge of the NCO_clk signal. The registers are readable and writable. The increment registers are double-buffered to allow value changes to be made without first disabling the NCO module. When the NCO module is disabled, the increment buffers are loaded immediately after a write to the increment registers. Important: The increment buffer registers are not user-accessible. Related Links NCOxINC 22.2 Fixed Duty Cycle Mode In Fixed Duty Cycle (FDC) mode, every time the accumulator overflows (NCO_overflow), the output is toggled at a frequency rate half of the FOVERFLOW. This provides a 50% duty cycle, provided that the increment value remains constant. For more information, see the figure below. The FDC mode is selected by clearing the PFM bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 317 PIC16(L)F18424/44 Filename: Title: Last Edit: First Used: Numerically Controlled Oscillator (NCO) Module 10-000029A.vsd NCO - Fixed Duty Cycle (FDC) and Pulse Frequency Mode (PFM) Output Operation Diagram 11/7/2013 PIC16(L)F1508/9 (LECD) Figure 22-3. FDC Output Mode Operation Diagram Rev. 10-000029A 11/7/2013 NCOx Clock Source NCOx Increment Value NCOx Accumulator Value 4000h 00000h 04000h 08000h 4000h FC000h 00000h 04000h 08000h 4000h FC000h 00000h 04000h 08000h NCO_overflow NCO_interrupt NCOx Output FDC Mode NCOx Output PF Mode NCOxPWS = 000 NCOx Output PF Mode NCOxPWS = 001 Related Links NCOxCON 22.3 Pulse Frequency Mode In Pulse Frequency (PF) mode, every time the Accumulator overflows, the output becomes active for one or more clock periods. Once the clock period expires, the output returns to an inactive state. This provides a pulsed output. The output becomes active on the rising clock edge immediately following the overflow event. For more information, see the figure above. The value of the active and inactive states depends on the POL bit. The PF mode is selected by setting the PFM bit. Related Links NCOxCON 22.3.1 Output Pulse Width Control When operating in PF mode, the active state of the output can vary in width by multiple clock periods. Various pulse widths are selected with the PWS bits. When the selected pulse width is greater than the Accumulator overflow time frame, then NCO output does not toggle. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 318 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module Related Links NCOxCLK 22.4 Output Polarity Control The last stage in the NCO module is the output polarity. The POL bit selects the output polarity. Changing the polarity while the interrupts are enabled will cause an interrupt for the resulting output transition. The NCO output signal (NCOx_out) is available to the following peripherals: * CLC * CWG * Timer1 * Timer2 * CLKR 22.5 Interrupts When the accumulator overflows (NCO_overflow), the NCO Interrupt Flag bit, NCO1IF, of the PIR7 register is set. To enable the interrupt event (NCO_interrupt), the following bits must be set: * EN bit * NCO1IE bit of the PIE7 register * PEIE bit of the INTCON register * GIE bit of the INTCON register The interrupt must be cleared by software by clearing the NCO1IF bit in the Interrupt Service Routine. Related Links NCOxCON INTCON PIR7 PIE7 22.6 Effects of a Reset All of the NCO registers are cleared to zero as the result of a Reset. 22.7 Operation in Sleep The NCO module operates independently from the system clock and will continue to run during Sleep, provided that the clock source selected remains active. The HFINTOSC remains active during Sleep when the NCO module is enabled and the HFINTOSC is selected as the clock source, regardless of the system clock source selected. In other words, if the HFINTOSC is simultaneously selected as the system clock and the NCO clock source, when the NCO is enabled, the CPU will go idle during Sleep, but the NCO will continue to operate and the HFINTOSC will remain active. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 319 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module This will have a direct effect on the Sleep mode current. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 320 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.8 Offset 0x058C Register Summary - NCO Name Bit Pos. NCO1ACC 7:0 ACCL[7:0] 15:8 ACCH[7:0] 23:16 0x058F NCO1INC ACCU[3:0] 7:0 INCL[7:0] 15:8 INCH[7:0] 23:16 0x0592 NCO1CON 7:0 0x0593 NCO1CLK 7:0 22.9 INCU[3:0] EN OUT POL PFM PWS[2:0] CKS[3:0] Register Definitions: NCO Long bit name prefixes for the NCO peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 22-2. NCO Long Bit Name Prefixes Peripheral Bit Name Prefix NCO NCO Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 321 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.9.1 NCOxCON Name: Offset: NCOxCON 0x0592 NCO Control Register Bit Access Reset 5 4 EN 7 6 OUT POL 3 2 1 PFM 0 R/W RO R/W R/W 0 0 0 0 Bit 7 - EN NCO Enable bit Value 1 0 Description NCO module is enabled NCO module is disabled Bit 5 - OUT NCO Output bit Displays the current output value of the NCO module. Bit 4 - POL NCO Polarity bit Value 1 0 Description NCO output signal is inverted NCO output signal is not inverted Bit 0 - PFM NCO Pulse Frequency Mode bit Value 1 0 Description NCO operates in Pulse Frequency mode NCO operates in Fixed Duty Cycle mode, divide by 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 322 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.9.2 NCOxCLK Name: Offset: NCOxCLK 0x0593 NCO Input Clock Control Register Bit 7 6 5 4 3 2 PWS[2:0] Access Reset 1 0 CKS[3:0] R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 Bits 7:5 - PWS[2:0] NCO Output Pulse Width Select bits(1) Value 111 110 101 100 011 010 001 000 Description NCO output is active for 128 input clock periods NCO output is active for 64 input clock periods NCO output is active for 32 input clock periods NCO output is active for 16 input clock periods NCO output is active for 8 input clock periods NCO output is active for 4 input clock periods NCO output is active for 2 input clock periods NCO output is active for 1 input clock periods Bits 3:0 - CKS[3:0] NCO Clock Source Select bits CKS values are available in the NCO Clock Sources table. Note: 1. PWS applies only when operating in Pulse Frequency mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 323 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.9.3 NCOxACC Name: Offset: NCOxACC 0x058C NCO Accumulator Register Bit 23 22 21 20 19 18 17 16 ACCU[3:0] Access Reset Bit R/W R/W R/W R/W 0 0 0 0 11 10 9 8 15 14 13 12 R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 ACCH[7:0] Access ACCL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 19:16 - ACCU[3:0] NCO Accumulator - Upper Byte(1) Bits 15:8 - ACCH[7:0] NCO Accumulator - High Byte Bits 7:0 - ACCL[7:0] NCO Accumulator - Low Byte Note: 1. The accumulator spans registers NCOxACCU:NCOxACCH: NCOxACCL. The 24 bits are reserved but not all are used. This register updates in real-time, asynchronously to the CPU; there is no provision to ensure atomic access to this 24-bit space using an 8-bit bus. Writing to this register while the module is operating will produce undefined results. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 324 PIC16(L)F18424/44 Numerically Controlled Oscillator (NCO) Module 22.9.4 NCOxINC Name: Offset: NCOxINC 0x058F NCO Increment Register Bit 23 22 21 20 19 18 17 16 INCU[3:0] Access Reset Bit R/W R/W R/W R/W 0 0 0 0 11 10 9 8 15 14 13 12 R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 INCH[7:0] Access INCL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 19:16 - INCU[3:0] NCO Increment - Upper Byte(1) Bits 15:8 - INCH[7:0] NCO Increment - High Byte(1) Bits 7:0 - INCL[7:0] NCO Increment - Low Byte(1,2) Note: 1. The logical increment spans NCOxINCU:NCOxINCH:NCOxINCL. 2. NCOxINC is double-buffered as INCBUF; INCBUF is updated on the next falling edge of NCOxCLK after writing to NCOxINCL; NCOxINCU and NCOxINCH should be written prior to writing NCOxINCL. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 325 PIC16(L)F18424/44 (CMP) Comparator Module 23. (CMP) Comparator Module Comparators are used to interface analog circuits to a digital circuit by comparing two analog voltages and providing a digital indication of their relative magnitudes. Comparators are very useful mixed-signal building blocks because they provide analog functionality independent of program execution. The PIC16(L)F18424/44 devices have 2 comparators (C1/C2). The analog comparator module includes the following features: * * * * * * * * * * * * 23.1 Programmable input selection Programmable output polarity Rising/falling output edge interrupts Wake-up from Sleep CWG Auto-shutdown source Selectable voltage reference ADC Auto-trigger Odd numbered timers (Timer1, Timer3, etc.) Gate Even numbered timers (Timer2, Timer4, etc.) Reset CCP Capture Mode Input DSM Modulator Source Input and Window Signal-to-Signal Measurement Timer Comparator Overview A single comparator is shown in Figure 23-1 along with the relationship between the analog input levels and the digital output. When the analog voltage at VIN+ is less than the analog voltage at VIN-, the output of the comparator is a digital low level. When the analog voltage at VIN+ is greater than the analog voltage at VIN-, the output of the comparator is a digital high level. Figure 23-1. Single Comparator Rev. 30-000125A 5/17/2017 VIN+ + VIN- - Output VINVIN+ Output Note: 1. The black areas of the output of the comparator represent the uncertainty due to input offsets and response time. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 326 Title: Last Edit: First Used: Notes: COMPARATOR BLOCK DIAGRAM 4/26/2017 PIC16(L)F184XX PIC16(L)F18424/44 (CMP) Comparator Module Figure 23-2. Comparator Module Simplified Block Diagram CxNCH<2:0> 3 Rev. 10-000027P 4/26/2017 CxON(1) CxIN0- 000 CxIN1- 001 CxIN2- 010 CxIN3- 011 Reserved 100 Reserved 101 FVR_buffer2 110 CxON(1) CxVN Interrupt Rising Edge CxINTP Interrupt Falling Edge CxINTN - set bit CxIF D CxOUT Q MCxOUT Cx CxVP 111 + Q1 CxSP CxHYS CxPOL CxOUT_sync CxIN0+ CxSYNC 000 Reserved 001 Reserved 010 Reserved 011 Reserved 100 DAC1_output 101 FVR_buffer2 110 TRIS bit 0 PPS D Q to peripherals CxOUT 1 (From Timer1 Module) T1CLK RxyPPS 111 CxPCH<2:0> 3 CxON(1) Related Links CMxNCH CMxPCH 23.2 Comparator Control Each comparator has two control registers: CMxCON0 and CMxCON1. The CMxCON0 register contains Control and Status bits for the following: * * * * * Enable Output Output polarity Hysteresis enable Timer1 output synchronization The CMxCON1 register contains Control bits for the following: * * * Interrupt on positive/negative edge enables Positive input channel selection Negative input channel selection (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 327 PIC16(L)F18424/44 (CMP) Comparator Module 23.2.1 Comparator Enable Setting the EN bit enables the comparator for operation. Clearing the CxEN bit disables the comparator, resulting in minimum current consumption. 23.2.2 Comparator Output The output of the comparator can be monitored by reading either the CxOUT bit or the MCxOUT bit. The comparator output can also be routed to an external pin through the RxyPPS register. The corresponding TRIS bit must be clear to enable the pin as an output. Note: 1. The internal output of the comparator is latched with each instruction cycle. Unless otherwise specified, external outputs are not latched. Related Links RxyPPS 23.2.3 Comparator Output Polarity Inverting the output of the comparator is functionally equivalent to swapping the comparator inputs. The polarity of the comparator output can be inverted by setting the CxPOL bit. Clearing the CxPOL bit results in a non-inverted output. Table 23-1 shows the output state versus input conditions, including polarity control. Table 23-1. Comparator Output State vs. Input Conditions 23.3 Input Condition CxPOL CxOUT CxVn > CxVp 0 0 CxVn < CxVp 0 1 CxVn > CxVp 1 1 CxVn < CxVp 1 0 Comparator Hysteresis A selectable amount of separation voltage can be added to the input pins of each comparator to provide a hysteresis function to the overall operation. Hysteresis is enabled by setting the CxHYS bit. See Comparator Specifications for more information. Related Links Comparator Specifications 23.4 Operation With Timer1 Gate The output resulting from a comparator operation can be used as a source for gate control of the odd numbered timers (Timer1, Timer3, etc.). See the timer gate section for more information. This feature is useful for timing the duration or interval of an analog event. It is recommended that the comparator output be synchronized to the timer by setting the SYNC bit. This ensures that the timer does not increment while a change in the comparator is occurring. However, (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 328 PIC16(L)F18424/44 (CMP) Comparator Module synchronization is only possible with the Timer1 clock source. Synchronization with the other odd numbered timers is only possible when they use the same clock source as Timer1. Related Links Timer1 Gate 23.4.1 Comparator Output Synchronization The output from a comparator can be synchronized with Timer1 by setting the SYNC bit. Once enabled, the comparator output is latched on the falling edge of the Timer1 source clock. If a prescaler is used with Timer1, the comparator output is latched after the prescaling function. To prevent a race condition, the comparator output is latched on the falling edge of the Timer1 clock source and Timer1 increments on the rising edge of its clock source. See the Figure 23-2 Comparator Block Diagram and the Timer1 Block Diagram for more information. Related Links Timer1 Module with Gate Control 23.5 Comparator Interrupt An interrupt can be generated upon a change in the output value of the comparator for each comparator; a rising edge detector and a falling edge detector are present. When either edge detector is triggered and its associated enable bit is set (CxINTP and/or CxINTN bits), the Corresponding Interrupt Flag bit (CxIF bit of the PIR2 register) will be set. To enable the interrupt, the following bits must be set: * * * * * EN and POL bits CxIE bit of the PIE2 register INTP bit (for a rising edge detection) INTN bit (for a falling edge detection) PEIE and GIE bits of the INTCON register The associated interrupt flag bit, CxIF bit of the PIR2 register, must be cleared in software. If another edge is detected while this flag is being cleared, the flag will still be set at the end of the sequence. Important: Although a comparator is disabled, an interrupt can be generated by changing the output polarity with the CxPOL bit, or by switching the comparator on or off with the CxEN bit. 23.6 Comparator Positive Input Selection Configuring the PCH bits direct an internal voltage reference or an analog pin to the non-inverting input of the comparator: PCH Positive Input Source 111 CxVP connects to VSS 110 CxVP connects to FVR Buffer 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 329 PIC16(L)F18424/44 (CMP) Comparator Module PCH Positive Input Source 101 CxVP connects to DAC1 output 100 CxVP not connected 011 CxVP not connected 010 CxVP not connected 001 CxVP connects to CxIN1+ pin 000 CxVP connects to CxIN0+ pin Important: To use CxINy+ pins as analog input, the appropriate bits must be set in the ANSEL register and the corresponding TRIS bits must also be set to disable the output drivers. See Fixed Voltage Reference (FVR) for more information on the Fixed Voltage Reference module. See 5-Bit Digital-to-Analog Converter (DAC) module for more information on the DAC input signal. Any time the comparator is disabled (CxEN = 0), all comparator inputs are disabled. Related Links (FVR) Fixed Voltage Reference (DAC) 5-Bit Digital-to-Analog Converter Module 23.7 Comparator Negative Input Selection The NCH bits direct an analog input pin and internal reference voltage or analog ground to the inverting input of the comparator: NCH Negative Input Sources 111 CxVN connects to AVSS 110 CxVN connects to FVR Buffer 2 101 CxVN not connected 100 CxVN not connected 011 CxVN connects to CxIN3- pin 010 CxVN connects to CxIN2- pin 001 CxVN connects to CxIN1- pin 000 CxVN connects to CxIN0- pin Important: To use CxINy- pins as analog input, the appropriate bits must be set in the ANSEL register and the corresponding TRIS bits must also be set to disable the output drivers. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 330 PIC16(L)F18424/44 (CMP) Comparator Module 23.8 Comparator Response Time The comparator output is indeterminate for a period of time after the change of an input source or the selection of a new reference voltage. This period is referred to as the response time. The response time of the comparator differs from the settling time of the voltage reference. Therefore, both of these times must be considered when determining the total response time to a comparator input change. See the Comparator and Voltage Reference Specifications in Comparator Specifications and Fixed Voltage Reference (FVR) Specifications for more details. Related Links Comparator Specifications Fixed Voltage Reference (FVR) Specifications 23.9 Analog Input Connection Considerations A simplified circuit for an analog input is shown in Figure 23-3. Since the analog input pins share their connection with a digital input, they have reverse biased ESD protection diodes to VDD and VSS. The analog input, therefore, must be between VSS and VDD. If the input voltage deviates from this range by more than 0.6V in either direction, one of the diodes is forward biased and a latch-up may occur. A maximum source impedance of 10 k is recommended for the analog sources. Also, any external component connected to an analog input pin, such as a capacitor or a Zener diode, should have very little leakage current to minimize inaccuracies introduced. Note: 1. When reading a PORT register, all pins configured as analog inputs will read as a `0'. Pins configured as digital inputs will convert as an analog input, according to the input specification. 2. Analog levels on any pin defined as a digital input, may cause the input buffer to consume more current than is specified. Figure 23-3. Analog Input Model Rev. 10-000071A 8/2/2013 VDD RS < 10K Analog Input pin VA CPIN 5pF VT 0.6V RIC To Comparator ILEAKAGE(1) VT 0.6V VSS Legend: CPIN ILEAKAGE RIC RS VA VT = Input Capacitance = Leakage Current at the pin due to various junctions = Interconnect Resistance = Source Impedance = Analog Voltage = Threshold Voltage Note: See Electrical Specifications chapter. Related Links Electrical Specifications (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 331 PIC16(L)F18424/44 (CMP) Comparator Module 23.10 CWG1 Auto-Shutdown Source The output of the comparator module can be used as an auto-shutdown source for the CWG1 module. When the output of the comparator is active and the corresponding WGASxE is enabled, the CWG operation will be suspended immediately. Related Links External Input Source 23.11 ADC Auto-Trigger Source The output of the comparator module can be used to trigger an ADC conversion. When the ADACT register is set to trigger on a comparator output, an ADC conversion will trigger when the comparator output goes high. 23.12 Even Numbered Timers Reset The output of the comparator module can be used to reset the even numbered timers (Timer2, Timer4, etc.). When the TxERS register is appropriately set, the timer will reset when the comparator output goes high. 23.13 Operation in Sleep Mode The comparator module can operate during Sleep. The comparator clock source is based on the Timer1 clock source. If the Timer1 clock source is either the system clock (FOSC) or the instruction clock (FOSC/4), Timer1 will not operate during Sleep, and synchronized comparator outputs will not operate. A comparator interrupt will wake the device from Sleep. The CxIE bits of the PIEx register must be set to enable comparator interrupts. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 332 PIC16(L)F18424/44 (CMP) Comparator Module 23.14 Register Summary - Comparator Offset Name Bit Pos. 0x098F CMOUT 7:0 0x0990 CM1CON0 7:0 0x0991 CM1CON1 7:0 0x0992 CM1NCH 7:0 NCH[2:0] 0x0993 CM1PCH 7:0 0x0994 CM2CON0 7:0 0x0995 CM2CON1 0x0996 CM2NCH 0x0997 CM2PCH 23.15 EN OUT POL MC2OUT MC1OUT HYS SYNC INTP INTN PCH[2:0] EN OUT POL HYS SYNC 7:0 INTP INTN 7:0 NCH[2:0] 7:0 PCH[2:0] Register Definitions: Comparator Control Long bit name prefixes for the comparator peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 23-2. Comparator Bit Name Prefixes Peripheral Bit Name Prefix C1 C1 C2 C2 Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 333 PIC16(L)F18424/44 (CMP) Comparator Module 23.15.1 CMxCON0 Name: Offset: CMxCON0 0x990,0x994 Comparator x Control Register 0 Bit Access Reset 7 6 1 0 EN OUT 5 POL 4 3 2 HYS SYNC R/W RO R/W R/W R/W 0 0 0 0 0 Bit 7 - EN Comparator Enable bit Value 1 0 Description Comparator is enabled Comparator is disabled and consumes no active power Bit 6 - OUT Comparator Output bit Value 1 0 1 0 Condition If POL = 0 (non-inverted polarity): If POL = 0 (non-inverted polarity): If POL = 1 (inverted polarity): If POL = 1 (inverted polarity): Description CxVP > CxVN CxVP < CxVN CxVP < CxVN CxVP > CxVN Bit 4 - POL Comparator Output Polarity Select bit Value 1 0 Description Comparator output is inverted Comparator output is not inverted Bit 1 - HYS Comparator Hysteresis Enable bit Value 1 0 Description Comparator hysteresis enabled Comparator hysteresis disabled Bit 0 - SYNC Comparator Output Synchronous Mode bit Output updated on the falling edge of prescaled Timer1 clock. Value 1 0 Description Comparator output to Timer1 and I/O pin is synchronous to changes on the prescaled Timer1 clock. Comparator output to Timer1 and I/O pin is asynchronous (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 334 PIC16(L)F18424/44 (CMP) Comparator Module 23.15.2 CMxCON1 Name: Offset: CMxCON1 0x991,0x995 Comparator x Control Register 1 Bit 7 6 5 4 3 Access Reset 2 1 0 INTP INTN R/W R/W 0 0 Bit 1 - INTP Comparator Interrupt on Positive-Going Edge Enable bit Value 1 0 Description The CxIF interrupt flag will be set upon a positive-going edge of the CxOUT bit No interrupt flag will be set on a positive-going edge of the CxOUT bit Bit 0 - INTN Comparator Interrupt on Negative-Going Edge Enable bit Value 1 0 Description The CxIF interrupt flag will be set upon a negative-going edge of the CxOUT bit No interrupt flag will be set on a negative-going edge of the CxOUT bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 335 PIC16(L)F18424/44 (CMP) Comparator Module 23.15.3 CMxNCH Name: Offset: CMxNCH 0x992,0x996 Comparator x Inverting Channel Select Register Bit 7 6 5 4 3 2 1 0 NCH[2:0] Access Reset R/W R/W R/W 0 0 0 Bits 2:0 - NCH[2:0] Comparator Inverting Input Channel Select bits NCH Negative Input Sources 111 CxVN connects to AVSS 110 CxVN connects to FVR Buffer 2 101 CxVN not connected 100 CxVN not connected 011 CxVN connects to CxIN3- pin 010 CxVN connects to CxIN2- pin 001 CxVN connects to CxIN1- pin 000 CxVN connects to CxIN0- pin (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 336 PIC16(L)F18424/44 (CMP) Comparator Module 23.15.4 CMxPCH Name: Offset: CMxPCH 0x993,0x997 Comparator x Non-Inverting Channel Select Register PCH Bit Positive Input Source 111 CxVP connects to VSS 110 CxVP connects to FVR Buffer 2 101 CxVP connects to DAC1 output 100 CxVP not connected 011 CxVP not connected 010 CxVP not connected 001 CxVP connects to CxIN1+ pin 000 CxVP connects to CxIN0+ pin 7 6 5 4 3 2 1 0 PCH[2:0] Access Reset R/W R/W R/W 0 0 0 Bits 2:0 - PCH[2:0] Comparator Non-Inverting Input Channel Select bits (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 337 PIC16(L)F18424/44 (CMP) Comparator Module 23.15.5 CMOUT Name: Offset: CMOUT 0x98F Comparator Output Register Bit 7 6 5 4 3 Access Reset 2 1 0 MC2OUT MC1OUT RO RO 0 0 Bits 0, 1 - MCxOUT Mirror copy of CxOUT bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 338 PIC16(L)F18424/44 Timer0 Module 24. Timer0 Module Timer0 module has the following features: * * * * * * * * 8-Bit B\Timer with Programmable Period 16-Bit Timer Selectable Clock Sources Synchronous and Asynchronous Operation Programmable Prescaler and Postscaler Filename: 10-000017D.vsd Title: TIMER0 16-BIT BLOCK DIAGRAM Interrupt on Match or Overflow Last Edit: 4/6/2017 Output (via PPS) or to Other Peripherals First Used:on I/O Pin PIC16(L)F153xx Notes: Operation During Sleep Figure 24-1. Timer0 Block Diagram Rev. 10-000017D 4/6/2017 CLC1 111 SOSC 110 MFINTOSC 101 LFINTOSC 100 HFINTOSC 011 FOSC/4 010 PPS 001 T0CKPS<3:0> Peripherals TMR0 body 1 Prescaler SYNC 0 IN T0OUTPS<3:0> OUT T0_out Postscaler TMR0 FOSC/4 T016BIT T0ASYNC 000 T0IF Q D T0CKIPPS PPS RxyPPS CK Q 3 T0CS<2:0> 16-bit TMR0 Body Diagram (T016BIT = 1) 8-bit TMR0 Body Diagram (T016BIT = 0) IN TMR0L R Clear IN TMR0L TMR0 High Byte OUT 8 COMPARATOR Read TMR0L OUT Write TMR0L T0_match 8 8 TMR0 High Byte TMR0H Latch Enable 8 TMR0H Internal Data Bus (c) 2018 Microchip Technology Inc. Datasheet Preliminary 8 DS40002000A-page 339 PIC16(L)F18424/44 Timer0 Module 24.1 Timer0 Operation Timer0 can operate as either an 8-bit or 16-bit timer. The mode is selected with the T016BIT bit. 24.1.1 8-bit Mode In this mode Timer0 increments on the rising edge of the selected clock source. A prescaler on the clock input gives several prescale options (see prescaler control bits, T0CKPS). In this mode as shown in the 8-bit TMR0 Body Diagram, a buffered version of TMR0H is maintained. This is compared with the value of TMR0L on each cycle of the selected clock source. When the two values match, the following events occur: * * 24.1.2 TMR0L is reset The contents of TMR0H are copied to the TMR0H buffer for next comparison 16-Bit Mode In this mode Timer0 increments on the rising edge of the selected clock source. A prescaler on the clock input gives several prescale options (see prescaler control bits, T0CKPS). In this mode TMR0H:TMR0L form the 16-bit timer value. As shown in the 16-bit TMR0 Body Diagram, read and write of the TMR0H register are buffered. TMR0H register is updated with the contents of the high byte of Timer0 during a read of TMR0L register. Similarly, a write to the high byte of Timer0 takes place through the TMR0H buffer register. The high byte is updated with the contents of TMR0H register when a write occurs to TMR0L register. This allows all 16 bits of Timer0 to be read and written at the same time. Timer0 rolls over to 0x0000 on incrementing past 0xFFFF. This makes the timer free running. TMR0L/H registers cannot be reloaded in this mode once started. 24.2 Clock Selection Timer0 has several options for clock source selections, option to operate synchronously/asynchronously and a programmable prescaler. 24.2.1 Clock Source Selection The T0CS bits are used to select the clock source for Timer0. The possible clock sources are listed in the table below. Table 24-1. Timer0 Clock Source Selections T0CS Clock Source 111 CLC1_out 110 SOSC 101 MFINTOSC(500 kHz) 100 LFINTOSC 011 HFINTOSC 010 FOSC/4 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 340 PIC16(L)F18424/44 Timer0 Module T0CS Clock Source 001 Pin selected by T0CKIPPS (Inverted) 000 Pin selected by T0CKIPPS (Noninverted) 24.2.2 Synchronous Mode When the T0ASYNC bit is clear, Timer0 clock is synchronized to the system clock (FOSC/4). When operating in Synchronous mode, Timer0 clock frequency cannot exceed FOSC/4. During Sleep mode system clock is not available and Timer0 cannot operate. 24.2.3 Asynchronous Mode When the T0ASYNC bit is set, Timer0 increments with each rising edge of the input source (or output of the prescaler, if used). Asynchronous mode allows Timer0 to continue operation during Sleep mode provided the selected clock source is available. 24.2.4 Programmable Prescaler Timer0 has 16 programmable input prescaler options ranging from 1:1 to 1:32768. The prescaler values are selected using the T0CKPS bits. The prescaler counter is not directly readable or writable. The prescaler counter is cleared on the following events: * * * A write to the TMR0L register A write to either the T0CON0 or T0CON1 registers Any device Reset Related Links Resets 24.3 Timer0 Output and Interrupt 24.3.1 Programmable Postscaler Timer0 has 16 programmable output postscaler options ranging from 1:1 to 1:16. The postscaler values are selected using the T0OUTPS bits. The postscaler divides the output of Timer0 by the selected ratio. The postscaler counter is not directly readable or writable. The postscaler counter is cleared on the following events: 24.3.2 * A write to the TMR0L register * * A write to either the T0CON0 or T0CON1 registers Any device Reset Timer0 Output TMR0_out is the output of the postscaler. TMR0_out toggles on every match between TMR0L and TMR0H in 8-bit mode, or when TMR0H:TMR0L rolls over in 16-bit mode. If the output postscaler is used, the output is scaled by the ratio selected. The Timer0 output can be routed to an I/O pin via the RxyPPS output selection register. The Timer0 output can be monitored through software via the T0OUT output bit. Related Links (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 341 PIC16(L)F18424/44 Timer0 Module PPS Outputs 24.3.3 Timer0 Interrupt The Timer0 Interrupt Flag bit (TMR0IF) is set when the TMR0_out toggles. If the Timer0 interrupt is enabled (TMR0IE), the CPU will be interrupted when the TMR0IF bit is set. When the postscaler bits (T0OUTPS) are set to 1:1 operation (no division), the T0IF flag bit will be set with every TMR0 match or rollover. In general, the TMR0IF flag bit will be set every T0OUTPS +1 matches or rollovers. 24.3.4 Timer0 Example Timer0 Configuration: * Timer0 mode = 16-bit * Clock Source = FOSC/4 (250 kHz) * Synchronous operation * Prescaler = 1:1 * Postscaler = 1:2 (T0OUTPS = 1) In this case the TMR0_out toggles every two rollovers of TMR0H:TMR0L. i.e., (0xFFFF)*2*(1/250kHz) = 524.28 ms 24.4 Operation During Sleep When operating synchronously, Timer0 will halt when the device enters Sleep mode. When operating asynchronously and selected clock source is active, Timer0 will continue to increment and wake the device from Sleep mode if Timer0 interrupt is enabled. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 342 PIC16(L)F18424/44 Timer0 Module 24.5 Register Summary - Timer0 Offset Name Bit Pos. 0x059C TMR0L 7:0 0x059D TMR0H 7:0 0x059E T0CON0 7:0 0x059F T0CON1 7:0 24.6 TMR0L[7:0] TMR0H[7:0] T0EN T0OUT T0CS[2:0] T016BIT T0OUTPS[3:0] T0ASYNC T0CKPS[3:0] Register Definitions: Timer0 Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 343 PIC16(L)F18424/44 Timer0 Module 24.6.1 T0CON0 Name: Offset: T0CON0 0x59E Timer0 Control Register 0 Bit Access Reset 5 4 T0EN 7 6 T0OUT T016BIT 3 R/W R R/W R/W 0 0 0 0 2 1 0 R/W R/W R/W 0 0 0 T0OUTPS[3:0] Bit 7 - T0EN TMR0 Enable bit Value 1 0 Description The module is enabled and operating The module is disabled Bit 5 - T0OUT TMR0 Output bit Bit 4 - T016BIT TMR0 Operating as 16-Bit Timer Select bit Value 1 0 Description TMR0 is a 16-bit timer TMR0 is an 8-bit timer Bits 3:0 - T0OUTPS[3:0] TMR0 Output Postscaler (Divider) Select bits Value 1111 1110 1101 1100 1011 1010 1001 1000 0111 0110 0101 0100 0011 0010 0001 0000 Description 1:16 Postscaler 1:15 Postscaler 1:14 Postscaler 1:13 Postscaler 1:12 Postscaler 1:11 Postscaler 1:10 Postscaler 1:9 Postscaler 1:8 Postscaler 1:7 Postscaler 1:6 Postscaler 1:5 Postscaler 1:4 Postscaler 1:3 Postscaler 1:2 Postscaler 1:1 Postscaler (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 344 PIC16(L)F18424/44 Timer0 Module 24.6.2 T0CON1 Name: Offset: T0CON1 0x59F Timer0 Control Register 1 Bit 7 6 5 T0CS[2:0] Access Reset 4 3 2 T0ASYNC 1 0 T0CKPS[3:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:5 - T0CS[2:0] Timer0 Clock Source Select bits Refer the clock source selection table Bit 4 - T0ASYNC TMR0 Input Asynchronization Enable bit Value 1 0 Description The input to the TMR0 counter is not synchronized to system clocks The input to the TMR0 counter is synchronized to Fosc/4 Bits 3:0 - T0CKPS[3:0] Prescaler Rate Select bit Value 1111 1110 1101 1100 1011 1010 1001 1000 0111 0110 0101 0100 0011 0010 0001 0000 Description 1:32768 1:16384 1:8192 1:4096 1:2048 1:1024 1:512 1:256 1:128 1:64 1:32 1:16 1:8 1:4 1:2 1:1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 345 PIC16(L)F18424/44 Timer0 Module 24.6.3 TMR0H Name: Offset: TMR0H 0x59D Timer0 Period/Count High Register Bit 7 6 5 4 3 2 1 0 TMR0H[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - TMR0H[7:0] TMR0 Most Significant Counter bits Value 0 to 255 0 to 255 Condition Description T016BIT = 0 8-bit Timer0 Period Value. TMR0L continues counting from 0 when this value is reached. T016BIT = 1 16-bit Timer0 Most Significant Byte (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 346 PIC16(L)F18424/44 Timer0 Module 24.6.4 TMR0L Name: Offset: TMR0L 0x59C Timer0 Period/Count Low Register Bit 7 6 5 4 3 2 1 0 TMR0L[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - TMR0L[7:0] TMR0 Least Significant Counter bits Value 0 to 255 0 to 255 Condition T016BIT = 0 T016BIT = 1 (c) 2018 Microchip Technology Inc. Description 8-bit Timer0 Counter bits 16-bit Timer0 Least Significant Byte Datasheet Preliminary DS40002000A-page 347 PIC16(L)F18424/44 Timer1 Module with Gate Control 25. Timer1 Module with Gate Control Timer1 module is a 16-bit timer/counter with the following features: * * * * * * * * * * * * * * * 16-Bit Timer/Counter Register Pair (TMRxH:TMRxL) Programmable Internal or External Clock Source 2-Bit Prescaler Optionally Synchronized Comparator Out Multiple Timer1 Gate (count enable) Sources Interrupt-on-Overflow Wake-Up on Overflow (external clock, Asynchronous mode only) 16-Bit Read/Write Operation Time Base for the Capture/Compare Function with the CCP modules Special Event Trigger (with CCP) Selectable Gate Source Polarity Gate Toggle mode Gate Single-Pulse mode Gate Value Status Gate Event Interrupt Important: References to module Timer1 apply to all the odd numbered timers on this device. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 348 Filename: Title: Last Edit: First Used: Note: 10-000018J.vsd TMR1 Block Diagram 8/15/2016 PIC16(L)F18424/44 16(L)F153xx 1: 2: 3: 4: 5: 6: Timer1 Module with Gate Control ST Buffer is high speed type when using TxCKIPPS. TMRx register increments on rising edge. Synchronize does not operate while in Sleep. See Register 25-3 for Clock source selections. See Register 25-4 for GATE source selections. Synchronized comparator output should not be used in conjunction with synchronized input clock. Figure 25-1. Timer1 Block Diagram TMRxGATE<4:0> Rev. 10-000018J 8/15/2016 4 TxGPPS TxGSPM PPS 00000 0 NOTE (5) 11111 1 D D Q 0 TxGVAL Q1 Q TxGGO/DONE TxGPOL CK TMRxON Q Interrupt R TxGTM set bit TMRxGIF det TMRxGE set flag bit TMRxIF Tx_overflow 1 Single Pulse Acq. Control TMRxH TMRxL TMRxON EN TMRx(2) Q To Comparators (6) Synchronized Clock Input 0 D 1 TxCLK TxSYNC TMRxCLK<3:0> 4 TxCKIPPS (1) PPS 0000 Note Prescaler 1,2,4,8 (4) 1111 2 TxCKPS<1:0> Synchronize(3) det Fosc/2 Internal Clock Sleep Input Note: 1. This signal comes from the pin seleted by TxCKIPPS. 2. TMRx register increments on rising edge. 3. Synchronize does not operate while in Sleep. 4. See TMRxCLK for clock source selections. 5. See TMRxGATE for gate source selection. 6. Synchronized comparator output should not be used in conjunction with synchronized input clock. 25.1 Timer1 Operation The Timer1 module is a 16-bit incrementing counter that is accessed through the TMRxH:TMRxL register pair. Writes to TMRxH or TMRxL directly update the counter. When used with an internal clock source, the module is a timer and increments on every instruction cycle. When used with an external clock source, the module can be used as either a timer or counter and increments on every selected edge of the external source. Timer1 is enabled by configuring the ON and GE bits in the TxCON and TxGCON registers, respectively. The table below displays the Timer1 enable selections. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 349 PIC16(L)F18424/44 Timer1 Module with Gate Control Table 25-1. Timer1 Enable Selections 25.2 ON GE Timer1 Operation 1 1 Count Enabled 1 0 Always On 0 1 Off 0 0 Off Clock Source Selection The CS bits select the clock source for Timer1. These bits allow the selection of several possible synchronous and asynchronous clock sources. The table below lists the clock source selections. Table 25-2. Timer Clock Sources Clock Source CS 25.2.1 Timer1 Timer3 Timer5 11111-10001 Reserved Reserved Reserved 10000 CLC4_out CLC4_out CLC4_out 01111 CLC3_out CLC3_out CLC3_out 01110 CLC2_out CLC2_out CLC2_out 01101 CLC1_out CLC1_out CLC1_out 01100 Timer5 overflow output Timer5 overflow output Reserved 01011 Timer3 overflow output Reserved Timer3 overflow output 01010 Reserved Timer1 overflow output Timer1 overflow output 01001 Timer0 overflow output Timer0 overflow output Timer0 overflow output 01000 CLKR output CLKR output CLKR output 00111 SOSC SOSC SOSC 00110 MFINTOSC (32 kHz) MFINTOSC (32 kHz) MFINTOSC (32 kHz) 00101 MFINTOSC (500 kHz) MFINTOSC (500 kHz) MFINTOSC (500 kHz) 00100 LFINTOSC LFINTOSC LFINTOSC 00011 HFINTOSC HFINTOSC HFINTOSC 00010 FOSC FOSC FOSC 00001 FOSC/4 FOSC/4 FOSC/4 00000 T1CKIPPS T3CKIPPS T5CKIPPS Internal Clock Source When the internal clock source is selected the TMRxH:TMRxL register pair will increment on multiples of FOSC as determined by the Timer1 prescaler. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 350 PIC16(L)F18424/44 Timer1 Module with Gate Control When the FOSC internal clock source is selected, the Timer1 register value will increment by four counts every instruction clock cycle. Due to this condition, a 2 LSB error in resolution will occur when reading the Timer1 value. To utilize the full resolution of Timer1, an asynchronous input signal must be used to gate the Timer1 clock input. Important: In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge after any one or more of the following conditions: * Timer1 enabled after POR * Write to TMRxH or TMRxL * Timer1 is disabled * Timer1 is disabled (TMRxON = 0) when TxCKI is high then Timer1 is enabled (TMRxON = 1) when TxCKI is low. Refer to the figure below. Figure 25-2. Timer1 Incrementing Edge Rev. 30-000136A 5/24/2017 TxCKI = 1 when TMRx Enabled TxCKI = 0 when TMRx Enabled Note: 1. Arrows indicate counter increments. 2. In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the clock. 25.2.2 External Clock Source When the external clock source is selected, the Timer1 module may work as a timer or a counter. When enabled to count, Timer1 is incremented on the rising edge of the external clock input of the TxCKIPPS pin. This external clock source can be synchronized to the system clock or it can run asynchronously. 25.3 Timer1 Prescaler Timer1 has four prescaler options allowing 1, 2, 4 or 8 divisions of the clock input. The CKPS bits control the prescale counter. The prescale counter is not directly readable or writable; however, the prescaler counter is cleared upon a write to TMRxH or TMRxL. 25.4 Secondary Oscillator A secondary low-power 32.768 kHz oscillator circuit is built-in between pins SOSCI (input) and SOSCO (amplifier output). This internal circuit is to be used in conjunction with an external 32.768 kHz crystal. The secondary oscillator is not dedicated only to Timer1; it can also be used by other modules. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 351 PIC16(L)F18424/44 Timer1 Module with Gate Control The oscillator circuit is enabled by setting the SOSCEN bit of the OSCEN register. This can be used as one of the Timer1 clock sources selected with the CS bits.The oscillator will continue to run during Sleep. Important: The oscillator requires a start-up and stabilization time before use. Thus, the SOSCEN bit of the OSCEN register should be set and a suitable delay observed prior to enabling Timer1. A software check can be performed to confirm if the secondary oscillator is enabled and ready to use. This is done by polling the SOR bit of the OSCSTAT. Related Links Secondary Oscillator 25.5 Timer1 Operation in Asynchronous Counter Mode When the SYNC control bit is set, the external clock input is not synchronized. The timer increments asynchronously to the internal phase clocks. If external clock source is selected then the timer will continue to run during Sleep and can generate an interrupt on overflow, which will wake-up the processor. However, special precautions in software are needed to read/write the timer (see Reading and Writing Timer1 in Asynchronous Counter Mode). Important: When switching from synchronous to asynchronous operation, it is possible to skip an increment. When switching from asynchronous to synchronous operation, it is possible to produce an additional increment. 25.5.1 Reading and Writing Timer1 in Asynchronous Counter Mode Reading TMRxH or TMRxL while the timer is running from an external asynchronous clock will ensure a valid read (taken care of in hardware). However, the user should keep in mind that reading the 16-bit timer in two 8-bit values itself, poses certain problems, since the timer may overflow between the reads. For writes, it is recommended that the user simply stop the timer and write the desired values. A write contention may occur by writing to the timer registers, while the register is incrementing. This may produce an unpredictable value in the TMRxH:TMRxL register pair. 25.6 Timer1 16-Bit Read/Write Mode Timer1 can be configured to read and write all 16 bits of data, to and from, the 8-bit TMRxL and TMRxH registers, simultaneously. The 16-bit read and write operations are enabled by setting the RD16 bit. To accomplish this function, the TMRxH register value is mapped to a buffer register called the TMRxH buffer register. While in 16-Bit mode, the TMRxH register is not directly readable or writable and all read and write operations take place through the use of this TMRxH buffer register. When a read from the TMRxL register is requested, the value of the TMRxH register is simultaneously loaded into the TMRxH buffer register. When a read from the TMRxH register is requested, the value is provided from the TMRxH buffer register instead. This provides the user with the ability to accurately read all 16 bits of the Timer1 value from a single instance in time. Refer the figure below for more details. In contrast, when not in 16-Bit mode, the user must read each register separately and determine if the values have become invalid due to a rollover that may have occurred between the read operations. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 352 PIC16(L)F18424/44 Timer1 Module with Gate Control When a write request of the TMRxL register is requested, the TMRxH buffer register is simultaneously updated with the contents of the TMRxH register. The value of TMRxH must be preloaded into the TMRxH buffer register prior to the write request for the TMRxL register. This provides the user with the ability to write all 16 bits to the TMRxL:TMRxH register pair at the same time. Any requests to write to the TMRxH directly does not clear the Timer1 prescaler value. The prescaler value is only cleared through write requests to the TMRxL register. Figure 25-3. Timer1 16-Bit Read/Write Mode Block Diagram From Timer1 Circuitry TMR1 High Byte TMR1L 8 Rev. 30-000135A 5/24/2017 Set TMR1IF on Overflow Read TMR1L Write TMR1L 8 8 TMR1H 8 8 Internal Data Bus 25.7 Timer1 Gate Timer1 can be configured to count freely or the count can be enabled and disabled using Timer1 gate circuitry. This is also referred to as Timer1 gate enable. Timer1 gate can also be driven by multiple selectable sources. 25.7.1 Timer1 Gate Enable The Timer1 Gate Enable mode is enabled by setting the GE bit. The polarity of the Timer1 Gate Enable mode is configured using the GPOL bit. When Timer1 Gate Enable mode is enabled, Timer1 will increment on the rising edge of the Timer1 clock source. When Timer1 Gate signal is inactive, the timer will not increment and hold the current count. Enable mode is disabled, no incrementing will occur and Timer1 will hold the current count. See figure below for timing details. Table 25-3. Timer1 Gate Enable Selections TMRxCLK GPOL TxG Timer1 Operation 1 1 Counts 1 0 Holds Count 0 1 Holds Count 0 0 Counts (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 353 PIC16(L)F18424/44 Timer1 Module with Gate Control Figure 25-4. Timer1 Gate Enable Mode Rev. 30-000137A 5/24/2017 TMRxGE TxGPOL TxG_IN TxCKI TxGVAL Timer1/3/5/7 25.7.2 N N+1 N+2 N+3 N+4 Timer1 Gate Source Selection The gate source for Timer1 is selected using the GSS bits. The polarity selection for the gate source is controlled by the GPOL bit. The table below lists the gate source selections. Table 25-4. Timer Gate Sources Gate Source GSS Timer1 Timer3 Timer5 11111-11001 Reserved Reserved Reserved 10110 CLC4_out CLC4_out CLC4_out 10101 CLC3_out CLC3_out CLC3_out 10100 CLC2_out CLC2_out CLC2_out 10011 CLC1_out CLC1_out CLC1_out 10010 ZCD1_output ZCD1_output ZCD1_output 10001 C2OUT_sync C2OUT_sync C2OUT_sync 10000 C1OUT_sync C1OUT_sync C1OUT_sync 01111 NCO1_out NCO1_out NCO1_out 01110 PWM7_out PWM7_out PWM7_out 01101 PWM6_out PWM6_out PWM6_out 01100 CCP4_out CCP4_out CCP4_out 01011 CCP3_out CCP3_out CCP3_out (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 354 PIC16(L)F18424/44 Timer1 Module with Gate Control Gate Source GSS Timer1 Timer3 Timer5 01010 CCP2_out CCP2_out CCP2_out 01001 CCP1_out CCP1_out CCP1_out 01000 SMT1_overflow SMT1_overflow SMT1_overflow 00111 TMR6_postscaled output TMR6_postscaled output TMR6_postscaled output 00110 Timer5 overflow output Timer5 overflow output Reserved 00101 TMR4_postscaled output TMR4_postscaled output TMR4_postscaled output 00100 Timer3 overflow output Reserved Timer3 overflow output 00011 TMR2_postscaled output TMR2_postscaled output TMR2_postscaled output 00010 Reserved Timer1 overflow output Timer1 overflow output 00001 Timer0 overflow output Timer0 overflow output Timer0 overflow output 00000 T1GPPS T3GPPS T5GPPS Any of the above mentioned signals can be used to trigger the gate. The output of the CMPx can be synchronized to the Timer1 clock or left asynchronous. For more information refer to the Comparator Output Synchronization section. Related Links Comparator Output Synchronization 25.7.3 Timer1 Gate Toggle Mode When Timer1 Gate Toggle mode is enabled, it is possible to measure the full-cycle length of a Timer1 gate signal, as opposed to the duration of a single level pulse. The Timer1 gate source is routed through a flip-flop that changes state on every incrementing edge of the signal. See figure below for timing details. Timer1 Gate Toggle mode is enabled by setting the GTM bit. When the GTM bit is cleared, the flip-flop is cleared and held clear. This is necessary in order to control which edge is measured. Important: Enabling Toggle mode at the same time as changing the gate polarity may result in indeterminate operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 355 PIC16(L)F18424/44 Timer1 Module with Gate Control Figure 25-5. TIMER1 GATE TOGGLE MODE Rev. 30-000138A 5/25/2017 TMRxGE TxGPOL TxGTM TxTxG_IN TxCKI TxGVAL TIMER1/3/5/7 25.7.4 N N+1 N+2 N+3 N+4 N+5 N+6 N+7 N+8 Timer1 Gate Single-Pulse Mode When Timer1 Gate Single-Pulse mode is enabled, it is possible to capture a single-pulse gate event. Timer1 Gate Single-Pulse mode is first enabled by setting the GSPM bit. Next, the GGO/DONE bit must be set. The Timer1 will be fully enabled on the next incrementing edge. On the next trailing edge of the pulse, the GGO/DONE bit will automatically be cleared. No other gate events will be allowed to increment Timer1 until the GGO/DONE bit is once again set in software. Clearing the GSPM bit will also clear the GGO/DONE bit. See figure below for timing details. Enabling the Toggle mode and the Single-Pulse mode simultaneously will permit both sections to work together. This allows the cycle times on the Timer1 gate source to be measured. See figure below for timing details. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 356 PIC16(L)F18424/44 Timer1 Module with Gate Control Figure 25-6. TIMER1 GATE SINGLE-PULSE MODE Rev. 30-000139A 5/25/2017 TMRxGE TxGPOL TxGSPM TxGGO/ Cleared by hardware on falling edge of TxGVAL Set by software DONE Counting enabled on rising edge of TxG TxG_IN TxCKI TxGVAL TIMER1/3/5/7 TMRxGIF N Cleared by software (c) 2018 Microchip Technology Inc. N+1 N+2 Set by hardware on falling edge of TxGVAL Datasheet Preliminary Cleared by software DS40002000A-page 357 PIC16(L)F18424/44 Timer1 Module with Gate Control Figure 25-7. TIMER1 GATE SINGLE-PULSE AND TOGGLE COMBINED MODE Rev. 30-000140A 5/25/2017 TMRxGE TxGPOL TxGSPM TxGTM TxGGO/ Cleared by hardware on falling edge of TxGVAL Set by software DONE Counting enabled on rising edge of TxG TxG_IN TxCKI TxGVAL TIMER1/3/5/7 TMRxGIF 25.7.5 N Cleared by software N+1 N+2 N+3 Set by hardware on falling edge of TxGVAL N+4 Cleared by software Timer1 Gate Value Status When Timer1 Gate Value Status is utilized, it is possible to read the most current level of the gate control value. The value is stored in the GVAL bit in the TxGCON register. The GVAL bit is valid even when the Timer1 gate is not enabled (GE bit is cleared). 25.7.6 Timer1 Gate Event Interrupt When Timer1 gate event interrupt is enabled, it is possible to generate an interrupt upon the completion of a gate event. When the falling edge of GVAL occurs, the TMRxGIF flag bit in the PIR5 register will be set. If the TMRxGIE bit in the PIE5 register is set, then an interrupt will be recognized. The TMRxGIF flag bit operates even when the Timer1 gate is not enabled (GE bit is cleared). For more information on selecting high or low priority status for the Timer1 gate event interrupt see the Interrupts chapter. 25.8 Timer1 Interrupt The Timer1 register pair (TMRxH:TMRxL) increments to FFFFh and rolls over to 0000h. When Timer1 rolls over, the Timer1 interrupt flag bit of the PIRx register is set. To enable the interrupt-on-rollover, the following bits must be set: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 358 PIC16(L)F18424/44 Timer1 Module with Gate Control * * * * TMRxON bit of the TxCON register TMRxIE bits of the PIEx register PEIE/GIEL bit of the INTCON register GIE/GIEH bit of the INTCON register The interrupt is cleared by clearing the TMRxIF bit in the Interrupt Service Routine. For more information on selecting high or low priority status for the Timer1 overflow interrupt, see the Interrupts chapter. Important: The TMRxH:TMRxL register pair and the TMRxIF bit should be cleared before enabling interrupts. 25.9 Timer1 Operation During Sleep Timer1 can only operate during Sleep when set up in Asynchronous Counter mode. In this mode, an external crystal or clock source can be used to increment the counter. To set up the timer to wake the device: * * * * * * TMRxON bit of the TxCON register must be set TMRxIE bit of the PIEx register must be set PEIE/GIEL bit of the INTCON register must be set TxSYNC bit of the TxCON register must be set Configure the TMRxCLK register for using secondary oscillator as the clock source Enable the SOSCEN bit of the OSCEN register The device will wake-up on an overflow and execute the next instruction. If the GIE/GIEH bit of the INTCON register is set, the device will call the Interrupt Service Routine. The secondary oscillator will continue to operate in Sleep regardless of the TxSYNC bit setting. 25.10 CCP Capture/Compare Time Base The CCP modules use the TMRxH:TMRxL register pair as the time base when operating in Capture or Compare mode. In Capture mode, the value in the TMRxH:TMRxL register pair is copied into the CCPRxH:CCPRxL register pair on a configured event. In Compare mode, an event is triggered when the value in the CCPRxH:CCPRxL register pair matches the value in the TMRxH:TMRxL register pair. This event can be a Special Event Trigger. For more information, see Capture/Compare/PWM Module(CCP) chapter. Related Links Capture/Compare/PWM Module (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 359 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.11 CCP Special Event Trigger When any of the CCPs are configured to trigger a special event, the trigger will clear the TMRxH:TMRxL register pair. This special event does not cause a Timer1 interrupt. The CCP module may still be configured to generate a CCP interrupt. In this mode of operation, the CCPRxH:CCPRxL register pair becomes the period register for Timer1. Timer1 should be synchronized and FOSC/4 should be selected as the clock source in order to utilize the Special Event Trigger. Asynchronous operation of Timer1 can cause a Special Event Trigger to be missed. In the event that a write to TMRxH or TMRxL coincides with a Special Event Trigger from the CCP, the write will take precedence. 25.12 Peripheral Module Disable When a peripheral is not used or inactive, the module can be disabled by setting the Module Disable bit in the PMD registers. This will reduce power consumption to an absolute minimum. Setting the PMD bits holds the module in Reset and disconnects the module's clock source. The Module Disable bits for Timer1 (TMR1MD) are in the PMD1 register. See Peripheral Module Disable (PMD) chapter for more information. Related Links Register Summary - PMD (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 360 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.13 Register Summary - Timer1 Offset Name 0x020C TMR1 0x020E T1CON 7:0 0x020F T1GCON 7:0 0x0210 TMR1GATE 7:0 GSS[4:0] 0x0211 TMR1CLK 7:0 CS[4:0] 0x0212 TMR3 0x0214 T3CON 7:0 0x0215 T3GCON 7:0 0x0216 TMR3GATE 7:0 0x0217 TMR3CLK 7:0 0x0218 Bit Pos. TMR5 7:0 TMRxL[7:0] 15:8 TMRxH[7:0] CKPS[1:0] GE GPOL GTM SYNC GSPM GGO/DONE 7:0 TMRxL[7:0] 15:8 TMRxH[7:0] CKPS[1:0] GE GPOL GTM GGO/DONE RD16 ON RD16 ON GVAL GSS[4:0] CS[4:0] 7:0 TMRxL[7:0] 15:8 TMRxH[7:0] 0x021A T5CON 7:0 0x021B T5GCON 7:0 0x021C TMR5GATE 7:0 GSS[4:0] 0x021D TMR5CLK 7:0 CS[4:0] 25.14 ON GVAL SYNC GSPM RD16 CKPS[1:0] GE GPOL GTM GSPM SYNC GGO/DONE GVAL Register Definitions: Timer1 Long bit name prefixes for the odd numbered timers is shown in the following table. Refer to the "Long Bit Names" section for more information. Table 25-5. Timer1 prefixes Peripheral Bit Name Prefix Timer1 T1 Timer3 T3 Timer5 T5 Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 361 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.14.1 TxCON Name: Offset: TxCON 0x20E,0x214,0x21A Timer Control Register Bit 7 6 5 4 3 CKPS[1:0] Access Reset 2 1 0 SYNC RD16 ON R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 5:4 - CKPS[1:0] Timer Input Clock Prescale Select bits Reset States: POR/BOR = 00 All Other Resets = uu Value 11 10 01 00 Description 1:8 Prescale value 1:4 Prescale value 1:2 Prescale value 1:1 Prescale value Bit 2 - SYNC Timer External Clock Input Synchronization Control bit Reset States: POR/BOR = 0 All Other Resets = u Value X 1 0 Condition CS = FOSC/4 or FOSC Else Else Description This bit is ignored. Timer uses the incoming clock as is. Do not synchronize external clock input Synchronize external clock input with system clock Bit 1 - RD16 16-Bit Read/Write Mode Enable bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description Enables register read/write of Timer in one 16-bit operation Enables register read/write of Timer in two 8-bit operations Bit 0 - ON Timer On bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description Enables Timer Disables Timer (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 362 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.14.2 TxGCON Name: Offset: TxGCON 0x20F,0x215,0x21B Timer Gate Control Register Bit Access Reset 7 6 5 4 3 2 GE GPOL GTM GSPM GGO/DONE GVAL R/W R/W R/W R/W R/W RO 0 0 0 0 0 x 1 0 Bit 7 - GE Timer Gate Enable bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 X Condition ON = 1 ON = 1 ON = 0 Description Timer counting is controlled by the Timer gate function Timer is always counting This bit is ignored Bit 6 - GPOL Timer Gate Polarity bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description Timer gate is active-high (Timer counts when gate is high) Timer gate is active-low (Timer counts when gate is low) Bit 5 - GTM Timer Gate Toggle Mode bit Timer Gate Flip-Flop Toggles on every rising edge Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description Timer Gate Toggle mode is enabled Timer Gate Toggle mode is disabled and Toggle flip-flop is cleared Bit 4 - GSPM Timer Gate Single Pulse Mode bit Reset States: POR/BOR = 0 All Other Resets = u Value 1 0 Description Timer Gate Single Pulse mode is enabled and is controlling Timer gate) Timer Gate Single Pulse mode is disabled Bit 3 - GGO/DONE Timer Gate Single Pulse Acquisition Status bit This bit is automatically cleared when TxGSPM is cleared. Reset States: POR/BOR = 0 All Other Resets = u (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 363 PIC16(L)F18424/44 Timer1 Module with Gate Control Value 1 0 Description Timer Gate Single Pulse Acquisition is ready, waiting for an edge Timer Gate Single Pulse Acquisition has completed or has not been started. Bit 2 - GVAL Timer Gate Current State bit Indicates the current state of the Timer gate that could be provided to TMRxH:TMRxL Unaffected by Timer Gate Enable (TMRxGE) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 364 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.14.3 TMRxCLK Name: Offset: TMRxCLK 0x211,0x217,0x21D Timer Clock Source Selection Register Bit 7 6 5 4 3 2 1 0 CS[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - CS[4:0] Timer Clock Source Selection bits Refer to the clock source selection table. Reset States: POR/BOR = 00000 All Other Resets = uuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 365 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.14.4 TMRxGATE Name: Offset: TMRxGATE 0x210,0x216,0x21C Timer Gate Source Selection Register Bit 7 6 5 4 3 2 1 0 GSS[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - GSS[4:0] Timer Gate Source Selection bits Refer to the gate source selection table. Reset States: POR/BOR = 00000 All Other Resets = uuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 366 PIC16(L)F18424/44 Timer1 Module with Gate Control 25.14.5 TMRx Name: Offset: TMRx 0x20C,0x212,0x218 Timer Low Byte Register Bit 15 14 13 12 11 10 9 8 TMRxH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 TMRxL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 15:8 - TMRxH[7:0] Timer Most Significant Byte Reset States: POR/BOR = 00000000 All Other Resets = uuuuuuuu Bits 7:0 - TMRxL[7:0] Timer Least Significant Byte Reset States: POR/BOR = 00000000 All Other Resets = uuuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 367 PIC16(L)F18424/44 Timer2 Module 26. Timer2 Module The Timer2 module is a 8-bit timer that incorporates the following features: * * * * * * * * * * * 8-Bit Timer and Period Registers Readable and Writable Software Programmable Prescaler (1:1 to 1:128) Software Programmable Postscaler (1:1 to 1:16) Interrupt on T2TMR Match with T2PR One-Shot Operation Full Asynchronous Operation Includes Hardware Limit Timer (HLT) Alternate Clock Sources External Timer Reset Signal Sources Configurable Timer Reset Operation See Figure 26-1 for a block diagram of Timer2. See table below for the clock source selections. Important: References to module Timer2 apply to all the even numbered timers on this device. (Timer2, Timer4, etc.) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 368 PIC16(L)F18424/44 Timer2 Module Figure 26-1. Timer2 with Hardware Limit Timer (HLT) Block Diagram RSEL <4:0> INPPS TxIN PPS External Reset (2) Sources Rev. 10-000168C 9/10/2015 MODE<4:0> TMRx_ers Edge Detector Level Detector Mode Control (2 clock Sync) MODE<3> reset CCP_pset(1) MODE<4:3>=01 enable D MODE<4:1>=1011 Q Clear ON CPOL Prescaler TMRx_clk 3 CKPS<2:0> ON Sync (2 Clocks) 0 Sync 1 Fosc/4 PSYNC TxTMR R Comparator Set flag bit TMRxIF Postscaler TMRx_postscaled 4 1 TxPR OUTPS<3:0> 0 CSYNC Note: 1. Signal to the CCP to trigger the PWM pulse. 2. See TxRST for external Reset sources. Table 26-1. Clock Source Selection CS<3:0> Clock Source Timer2 Timer4 Timer6 1111 Reserved Reserved Reserved 1110 CLC4_out CLC4_out CLC4_out 1101 CLC3_out CLC3_out CLC3_out 1100 CLC2_out CLC2_out CLC2_out 1011 CLC1_out CLC1_out CLC1_out 1010 ZCD1_output ZCD1_output ZCD1_output 1001 NCO1_out NCO1_out NCO1_out 1000 CLKR CLKR CLKR 0111 SOSC SOSC SOSC (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 369 PIC16(L)F18424/44 Timer2 Module Clock Source CS<3:0> 26.1 Timer2 Timer4 Timer6 0110 MFINTOSC(31.25 kHz) MFINTOSC(31.25 kHz) MFINTOSC(31.25 kHz) 0101 MFINTOSC(500 kHz) MFINTOSC(500 kHz) MFINTOSC(500 kHz) 0100 LFINTOSC LFINTOSC LFINTOSC 0011 HFINTOSC(32 MHz) HFINTOSC(32 MHz) HFINTOSC(32 MHz) 0010 FOSC FOSC FOSC 0001 FOSC/4 FOSC/4 FOSC/4 0000 T2CKIPPS T4CKIPPS T6CKIPPS Timer2 Operation Timer2 operates in three major modes: * * * Free Running Period One-shot Monostable Within each mode there are several options for starting, stopping, and reset. Table 26-3 lists the options. In all modes, the T2TMR count register is incremented on the rising edge of the clock signal from the programmable prescaler. When T2TMR equals T2PR, a high level is output to the postscaler counter. T2TMR is cleared on the next clock input. An external signal from hardware can also be configured to gate the timer operation or force a T2TMR count Reset. In Gate modes the counter stops when the gate is disabled and resumes when the gate is enabled. In Reset modes the T2TMR count is reset on either the level or edge from the external source. The T2TMR and T2PR registers are both directly readable and writable. The T2TMR register is cleared and the T2PR register initializes to FFh on any device Reset. Both the prescaler and postscaler counters are cleared on the following events: * * * * A write to the T2TMR register A write to the T2CON register Any device Reset External Reset Source event that resets the timer. Important: T2TMR is not cleared when T2CON is written. 26.1.1 Free Running Period Mode The value of T2TMR is compared to that of the Period register, T2PR, on each clock cycle. When the two values match, the comparator resets the value of T2TMR to 00h on the next cycle and increments the output postscaler counter. When the postscaler count equals the value in the OUTPS bits of the T2CON (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 370 PIC16(L)F18424/44 Timer2 Module register then a one clock period wide pulse occurs on the TMR2_postscaled output, and the postscaler count is cleared. 26.1.2 One-Shot Mode The One-Shot mode is identical to the Free Running Period mode except that the ON bit is cleared and the timer is stopped when T2TMR matches T2PR and will not restart until the ON bit is cycled off and on. Postscaler (OUTPS) values other than zero are ignored in this mode because the timer is stopped at the first period event and the postscaler is reset when the timer is restarted. 26.1.3 Monostable Mode Monostable modes are similar to One-Shot modes except that the ON bit is not cleared and the timer can be restarted by an external Reset event. 26.2 Timer2 Output The Timer2 module's primary output is TMR2_postscaled, which pulses for a single TMR2_clk period upon each match of the postscaler counter and the OUTPS bits of the T2CON register. The postscaler is incremented each time the T2TMR value matches the T2PR value. This signal can be selected as an input to several other input modules: * * * * * * The ADC module, as an auto-conversion trigger CWG, as an auto-shutdown source The CRC memory scanner, as a trigger for triggered mode Gate source for odd numbered timers (Timer1, Timer3, etc.) Alternate SPI clock Reset signals for other instances of even numbered timers (Timer2, Timer4, etc.) In addition, the Timer2 is also used by the CCP module for pulse generation in PWM mode. See "PWM Overview" and "Pulse-width Modulation" sections for more details on setting up Timer2 for use with the CCP and PWM modules. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.3 External Reset Sources In addition to the clock source, the Timer2 also takes in an external Reset source. This external Reset source is selected for each timer with the corresponding TxRST register. This source can control starting and stopping of the timer, as well as resetting the timer, depending on which mode the timer is in. Reset source selections are shown in the following table. Table 26-2. External Reset Sources RSEL<3:0> Reset Source TMR2 TMR4 TMR6 1111 Reserved Reserved Reserved 1101 CLC4_out CLC4_out CLC4_out (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 371 PIC16(L)F18424/44 Timer2 Module Reset Source RSEL<3:0> 26.4 TMR2 TMR4 TMR6 1100 CLC3_out CLC3_out CLC3_out 1011 CLC2_out CLC2_out CLC2_out 1010 CLC1_out CLC1_out CLC1_out 1001 ZCD1_output ZCD1_output ZCD1_output 1000 C2OUT_sync C2OUT_sync C2OUT_sync 0111 C1OUT_sync C1OUT_sync C1OUT_sync 0110 PWM7_out PWM7_out PWM7_out 0101 PWM6_out PWM6_out PWM6_out 0100 CCP4_out CCP4_out CCP4_out 0011 CCP3_out CCP3_out CCP3_out 0010 CCP2_out CCP2_out CCP2_out 0001 CCP1_out CCP1_out CCP1_out 0000 T2INPPS T4INPPS T6INPPS Timer2 Interrupt Timer2 can also generate a device interrupt. The interrupt is generated when the postscaler counter matches with the selected postscaler value (OUTPS bits of T2CON register). The interrupt is enabled by setting the TMR2IE interrupt enable bit. Interrupt timing is illustrated in the figure below. Figure 26-2. Timer2 Prescaler, Postscaler, and Interrupt Timing Diagram Rev. 10-000205A 4/7/2016 0b010 CKPS PRx 1 OUTPS 0b0001 TMRx_clk TMRx 0 1 0 1 0 1 0 TMRx_postscaled TMRxIF (1) (2) (1) Note: 1. Setting the interrupt flag is synchronized with the instruction clock. 2. Cleared by software. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 372 PIC16(L)F18424/44 Timer2 Module 26.5 Operating Modes The mode of the timer is controlled by the MODE bits of the T2HLT register. Edge-Triggered modes require six Timer clock periods between external triggers. Level-Triggered modes require the triggering level to be at least three Timer clock periods long. External triggers are ignored while in Debug mode. Table 26-3. Operating Modes Table Mode Free Running Period MODE<4:0> <4:3> <2:0> 00 Output Operation Timer Control Start Reset Stop 000 Software gate (Figure 26-3) ON = 1 -- ON = 0 ON = 1 and TMRx_ers = 1 -- 001 Hardware gate, activehigh (Figure 26-4) ON = 0 or TMRx_ers = 0 Hardware gate, activelow ON = 1 and TMRx_ers = 0 -- 010 ON = 0 or TMRx_ers = 1 011 Rising or falling edge Reset TMRx_ers Rising edge Reset (Figure 26-5) TMRx_ers 100 101 110 Period Pulse Period Pulse with Hardware Reset 111 000 One-shot 001 One-shot Operation 01 010 Edge Triggered Start (Note 1) 011 (c) 2018 Microchip Technology Inc. Falling edge Reset ON = 1 ON = 0 TMRx_ers Low level Reset TMRx_ers =0 High level Reset (Figure 26-6) TMRx_ers =1 Software start (Figure 26-7) ON = 1 Rising edge start (Figure 26-8) ON = 1 and TMRx_ers Falling edge start ON = 1 and TMRx_ers -- Any edge start ON = 1 and TMRx_ers -- ON = 0 or TMRx_ers = 0 ON = 0 or TMRx_ers = 1 -- -- ON = 0 or Next clock after Datasheet Preliminary TMRx = PRx (Note 2) DS40002000A-page 373 PIC16(L)F18424/44 Timer2 Module Mode MODE<4:0> <4:3> <2:0> Output Operation 100 101 Edge Triggered Start and 110 Hardware Reset (Note 1) 111 Operation Start Reset Rising edge start and Rising edge Reset (Figure 26-9) ON = 1 and TMRx_ers TMRx_ers Falling edge start and Falling edge Reset ON = 1 and TMRx_ers TMRx_ers Rising edge start and Low level Reset (Figure 26-10) ON = 1 and TMRx_ers TMRx_ers =0 Falling edge start and High level Reset ON = 1 and TMRx_ers TMRx_ers =1 000 001 Monostable 010 Edge Triggered Start 011 Reserved 10 Rising edge start (Figure 26-11) ON = 1 and TMRx_ers Falling edge start ON = 1 and TMRx_ers -- Any edge start ON = 1 and TMRx_ers -- 100 Reserved 101 Reserved 110 Level Triggered Start One-shot and 111 (c) 2018 Microchip Technology Inc. Stop Reserved (Note 1) Reserved Timer Control Hardware Reset High level start and Low level Reset (Figure 26-12) ON = 1 and TMRx_ers = 1 Low level start & High level Reset ON = 1 and TMRx_ers = 0 Datasheet Preliminary ON = 0 or -- Next clock after TMRx = PRx (Note 3) TMRx_ers =0 ON = 0 or Held in Reset (Note 2) TMRx_ers =1 DS40002000A-page 374 PIC16(L)F18424/44 Timer2 Module Mode Reserved MODE<4:0> <4:3> <2:0> 11 xxx Output Operation Operation Timer Control Start Reset Stop Reserved Note: 1. If ON = 0 then an edge is required to restart the timer after ON = 1. 2. 3. 26.6 When T2TMR = T2PR then the next clock clears ON and stops T2TMR at 00h. When T2TMR = T2PR then the next clock stops T2TMR at 00h but does not clear ON. Operation Examples Unless otherwise specified, the following notes apply to the following timing diagrams: * * * * Both the prescaler and postscaler are set to 1:1 (both the CKPS and OUTPS bits in the T2CON register are cleared). The diagrams illustrate any clock except FOSC/4 and show clock-sync delays of at least two full cycles for both ON and Timer2_ers. When using FOSC/4, the clock-sync delay is at least one instruction period for Timer2_ers; ON applies in the next instruction period. ON and Timer2_ers are somewhat generalized, and clock-sync delays may produce results that are slightly different than illustrated. The PWM Duty Cycle and PWM output are illustrated assuming that the timer is used for the PWM function of the CCP module as described in the "PWM Overview" section. The signals are not a part of the Timer2 module. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.1 Software Gate Mode This mode corresponds to legacy Timer2 operation. The timer increments with each clock input when ON = 1 and does not increment when ON = 0. When the TMRx count equals the PRx period count the timer resets on the next clock and continues counting from 0. Operation with the ON bit software controlled is illustrated in Figure 26-3. With PRx = 5, the counter advances until TMRx = 5, and goes to zero with the next clock. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 375 PIC16(L)F18424/44 Timer2 Module Figure 26-3. Software Gate Mode Timing Diagram (MODE = 00000) Rev. 10-000195B 5/30/2014 0b00000 MODE TMRx_clk Instruction(1) BSF BCF BSF ON PRx TMRx 5 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0 1 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.2 Hardware Gate Mode The Hardware Gate modes operate the same as the Software Gate mode except the TMRx_ers external signal can also gate the timer. When used with the CCP, the gating extends the PWM period. If the timer is stopped when the PWM output is high, then the duty cycle is also extended. When MODE<4:0> = 00001 then the timer is stopped when the external signal is high. When MODE<4:0> = 00010, then the timer is stopped when the external signal is low. Figure 26-4 illustrates the Hardware Gating mode for MODE<4:0> = 00001 in which a high input level starts the counter. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 376 PIC16(L)F18424/44 Timer2 Module Figure 26-4. Hardware Gate Mode Timing Diagram (MODE = 00001) Rev. 10-000 196B 5/30/201 4 MODE 0b00001 TMRx_clk TMRx_ers 5 PRx TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0 1 TMRx_postscaled PWM Duty Cycle 3 PWM Output Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.3 Edge-Triggered Hardware Limit Mode In Hardware Limit mode, the timer can be reset by the TMRx_ers external signal before the timer reaches the period count. Three types of Resets are possible: * Reset on rising or falling edge (MODE<4:0>= 00011) * Reset on rising edge (MODE<4:0> = 00100) * Reset on falling edge (MODE<4:0> = 00101) When the timer is used in conjunction with the CCP in PWM mode then an early Reset shortens the period and restarts the PWM pulse after a two clock delay. Refer to Figure 26-5. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 377 PIC16(L)F18424/44 Timer2 Module Figure 26-5. Edge-Triggered Hardware Limit Mode Timing Diagram (MODE = 00100) Rev. 10-000 197B 5/30/201 4 0b00100 MODE TMRx_clk PRx 5 Instruction(1) BSF BCF BSF ON TMRx_ers TMRx 0 1 2 0 1 2 3 4 5 0 1 2 3 4 5 0 1 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.4 Level-Triggered Hardware Limit Mode In the Level-Triggered Hardware Limit Timer modes the counter is reset by high or low levels of the external signal TMRx_ers, as shown in Figure 26-6. Selecting MODE<4:0> = 00110 will cause the timer to reset on a low level external signal. Selecting MODE<4:0> = 00111 will cause the timer to reset on a high level external signal. In the example, the counter is reset while TMRx_ers = 1. ON is controlled by BSF and BCF instructions. When ON = 0 the external signal is ignored. When the CCP uses the timer as the PWM time base then the PWM output will be set high when the timer starts counting and then set low only when the timer count matches the CCPRx value. The timer is reset when either the timer count matches the PRx value or two clock periods after the external Reset signal goes true and stays true. The timer starts counting, and the PWM output is set high, on either the clock following the PRx match or two clocks after the external Reset signal relinquishes the Reset. The PWM output will remain high until the timer counts up to match the CCPRx pulse width value. If the external Reset signal goes true while the PWM output is high then the PWM output will remain high until the Reset signal is released allowing the timer to count up to match the CCPRx value. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 378 PIC16(L)F18424/44 Timer2 Module Figure 26-6. Level-Triggered Hardware Limit Mode Timing Diagram (MODE = 00111) Rev. 10-000198B 5/30/2014 MODE 0b00111 TMRx_clk 5 PRx Instruction(1) BSF BCF BSF ON TMRx_ers TMRx 0 1 2 0 1 2 3 4 5 0 0 1 2 3 4 5 0 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.5 Software Start One-Shot Mode In One-Shot mode the timer resets and the ON bit is cleared when the timer value matches the PRx period value. The ON bit must be set by software to start another timer cycle. Setting MODE<4:0> = 01000 selects One-Shot mode which is illustrated in Figure 26-7. In the example, ON is controlled by BSF and BCF instructions. In the first case, a BSF instruction sets ON and the counter runs to completion and clears ON. In the second case, a BSF instruction starts the cycle, BCF/BSF instructions turn the counter off and on during the cycle, and then it runs to completion. When One-Shot mode is used in conjunction with the CCP PWM operation the PWM pulse drive starts concurrent with setting the ON bit. Clearing the ON bit while the PWM drive is active will extend the PWM drive. The PWM drive will terminate when the timer value matches the CCPRx pulse width value. The PWM drive will remain off until software sets the ON bit to start another cycle. If software clears the ON bit after the CCPRx match but before the PRx match then the PWM drive will be extended by the length of time the ON bit remains cleared. Another timing cycle can only be initiated by setting the ON bit after it has been cleared by a PRx period count match. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 379 PIC16(L)F18424/44 Timer2 Module Figure 26-7. Software Start One-shot Mode Timing Diagram (MODE = 01000) Rev. 10-000199B 4/7/2016 MODE 0b01000 TMRx_clk 5 PRx Instruction(1) BSF BSF BCF BSF ON TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.6 Edge-Triggered One-Shot Mode The Edge-Triggered One-Shot modes start the timer on an edge from the external signal input, after the ON bit is set, and clear the ON bit when the timer matches the PRx period value. The following edges will start the timer: * Rising edge (MODE<4:0> = 01001) * Falling edge (MODE<4:0> = 01010) * Rising or Falling edge (MODE<4:0> = 01011) If the timer is halted by clearing the ON bit then another TMRx_ers edge is required after the ON bit is set to resume counting. Figure 26-8 illustrates operation in the rising edge One-Shot mode. When Edge-Triggered One-Shot mode is used in conjunction with the CCP then the edge-trigger will activate the PWM drive and the PWM drive will deactivate when the timer matches the CCPRx pulse width value and stay deactivated when the timer halts at the PRx period count match. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 380 PIC16(L)F18424/44 Timer2 Module Figure 26-8. Edge-Triggered One-Shot Mode Timing Diagram (MODE = 01001) Rev. 10-000200B 5/19/2016 MODE 0b01001 TMRx_clk 5 PRx Instruction(1) BSF BSF BCF ON TMRx_ers TMRx 0 1 2 3 4 5 0 1 2 CCP_pset TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.7 Edge-Triggered Hardware Limit One-Shot Mode In Edge-Triggered Hardware Limit One-Shot modes the timer starts on the first external signal edge after the ON bit is set and resets on all subsequent edges. Only the first edge after the ON bit is set is needed to start the timer. The counter will resume counting automatically two clocks after all subsequent external Reset edges. Edge triggers are as follows: * Rising edge start and Reset (MODE<4:0> = 01100) * Falling edge start and Reset (MODE<4:0> = 01101) The timer resets and clears the ON bit when the timer value matches the PRx period value. External signal edges will have no effect until after software sets the ON bit. Figure 26-9 illustrates the rising edge hardware limit one-shot operation. When this mode is used in conjunction with the CCP then the first starting edge trigger, and all subsequent Reset edges, will activate the PWM drive. The PWM drive will deactivate when the timer matches the CCPRx pulse-width value and stay deactivated until the timer halts at the PRx period match unless an external signal edge resets the timer before the match occurs. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 381 PIC16(L)F18424/44 Timer2 Module Figure 26-9. Edge-Triggered Hardware Limit One-Shot Mode Timing Diagram (MODE = 01100) Rev. 10-000201B 4/7/2016 0b01100 MODE TMRx_clk 5 PRx Instruction(1) BSF BSF ON TMRx_ers TMRx 0 1 2 3 4 5 0 1 2 0 1 2 3 4 5 0 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.8 Level Reset, Edge-Triggered Hardware Limit One-Shot Modes In Level -Triggered One-Shot mode the timer count is reset on the external signal level and starts counting on the rising/falling edge of the transition from Reset level to the active level while the ON bit is set. Reset levels are selected as follows: * Low Reset level (MODE<4:0> = 01110) * High Reset level (MODE<4:0> = 01111) When the timer count matches the PRx period count, the timer is reset and the ON bit is cleared. When the ON bit is cleared by either a PRx match or by software control, a new external signal edge is required after the ON bit is set to start the counter. When Level-Triggered Reset One-Shot mode is used in conjunction with the CCP PWM operation, the PWM drive goes active with the external signal edge that starts the timer. The PWM drive goes inactive when the timer count equals the CCPRx pulse width count. The PWM drive does not go active when the timer count clears at the PRx period count match. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 382 PIC16(L)F18424/44 Timer2 Module Figure 26-10. Low Level Reset, Edge-Triggered hardware Limit one-Shot Mode Timing Diagram (MODE = 01110) Rev. 10-000202B 4/7/2016 0b01110 MODE TMRx_clk PRx Instruction(1) 5 BSF BSF ON TMRx_ers TMRx 0 1 2 3 4 5 0 1 0 1 2 3 4 5 0 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.9 Edge-Triggered Monostable Modes The Edge-Triggered Monostable modes start the timer on an edge from the external Reset signal input, after the ON bit is set, and stop incrementing the timer when the timer matches the PRx period value. The following edges will start the timer: * Rising edge (MODE<4:0> = 10001) * Falling edge (MODE<4:0> = 10010) * Rising or Falling edge (MODE<4:0> = 10011) When an Edge-Triggered Monostable mode is used in conjunction with the CCP PWM operation, the PWM drive goes active with the external Reset signal edge that starts the timer, but will not go active when the timer matches the PRx value. While the timer is incrementing, additional edges on the external Reset signal will not affect the CCP PWM. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 383 PIC16(L)F18424/44 Timer2 Module Figure 26-11. Rising Edge-Triggered Monostable Mode Timing Diagram (MODE = 10001) Rev. 10-000203A 4/7/2016 0b10001 MODE TMRx_clk PRx Instruction(1) 5 BSF BCF BSF BCF BSF ON TMRx_ers TMRx 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0 TMRx_postscaled PWM Duty Cycle 3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.6.10 Level-Triggered Hardware Limit One-Shot Modes The Level-Triggered Hardware Limit One-Shot modes hold the timer in Reset on an external Reset level and start counting when both the ON bit is set and the external signal is not at the Reset level. If one of either the external signal is not in Reset or the ON bit is set, then the other signal being set/made active will start the timer. Reset levels are selected as follows: * Low Reset level (MODE<4:0> = 10110) * High Reset level (MODE<4:0> = 10111) When the timer count matches the PRx period count, the timer is reset and the ON bit is cleared. When the ON bit is cleared by either a PRx match or by software control, the timer will stay in Reset until both the ON bit is set and the external signal is not at the Reset level. When Level-Triggered Hardware Limit One-Shot modes are used in conjunction with the CCP PWM operation, the PWM drive goes active with either the external signal edge or the setting of the ON bit, whichever of the two starts the timer. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 384 PIC16(L)F18424/44 Timer2 Module Figure 26-12. Level-Triggered hardware Limit one-Shot Mode Timing Diagram (MODE = 10110) Rev. 10-000204A 4/7/2016 0b10110 MODE TMR2_clk 5 PRx Instruction(1) BSF BSF BCF BSF ON TMR2_ers TMRx 0 1 2 3 4 5 0 1 2 3 0 1 2 3 4 5 0 TMR2_postscaled PWM Duty Cycle `D3 PWM Output Note: 1. BSF and BCF represent Bit-Set File and Bit-Clear File instructions executed by the CPU to set or clear the ON bit of TxCON. CPU execution is asynchronous to the timer clock input. Related Links PWM Overview (PWM) Pulse-Width Modulation 26.7 Timer2 Operation During Sleep When PSYNC = 1, Timer2 cannot be operated while the processor is in Sleep mode. The contents of the T2TMR and T2PR registers will remain unchanged while processor is in Sleep mode. When PSYNC = 0, Timer2 will operate in Sleep as long as the clock source selected is also still running. If any internal oscillator is selected as the clock source, it will stay active during Sleep mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 385 PIC16(L)F18424/44 Timer2 Module 26.8 Register Summary - Timer2 Offset Name Bit Pos. 0x028C T2TMR 7:0 0x028D T2PR 7:0 0x028E T2CON 7:0 ON 0x028F T2HLT 7:0 PSYNC 0x0290 T2CLKCON 7:0 CS[3:0] 0x0291 T2RST 7:0 RSEL[3:0] 0x0292 T4TMR 7:0 0x0293 T4PR 7:0 0x0294 T4CON 7:0 ON 0x0295 T4HLT 7:0 PSYNC 0x0296 T4CLKCON 7:0 0x0297 T4RST 7:0 0x0298 T6TMR 7:0 TxTMR[7:0] 0x0299 T6PR 7:0 TxPR[7:0] TxTMR[7:0] TxPR[7:0] CKPS[2:0] CPOL OUTPS[3:0] CSYNC MODE[4:0] TxTMR[7:0] TxPR[7:0] CKPS[2:0] CPOL OUTPS[3:0] CSYNC MODE[4:0] CS[3:0] RSEL[3:0] 0x029A T6CON 7:0 ON 0x029B T6HLT 7:0 PSYNC 0x029C T6CLKCON 7:0 CS[3:0] 0x029D T6RST 7:0 RSEL[3:0] 26.9 CKPS[2:0] CPOL OUTPS[3:0] CSYNC MODE[4:0] Register Definitions: Timer2 Control Long bit name prefixes for the Timer2 peripherals are shown in table below. Refer to Section "Long Bit Names" for more information. Table 26-4. Timer2 long bit name prefixes Peripheral Bit Name Prefix Timer2 T2 Timer4 T4 Timer6 T6 Notice: References to module Timer2 apply to all the even numbered timers on this device. (Timer2, Timer4, etc.) Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 386 PIC16(L)F18424/44 Timer2 Module 26.9.1 TxTMR Name: Offset: TxTMR 0x28C,0x292,0x298 Timer Counter Register Bit 7 6 5 4 3 2 1 0 TxTMR[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - TxTMR[7:0] Timerx Counter bits (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 387 PIC16(L)F18424/44 Timer2 Module 26.9.2 TxPR Name: Offset: TxPR 0x28D,0x293,0x299 Timer Period Register Bit 7 6 5 4 3 2 1 0 TxPR[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 7:0 - TxPR[7:0] Timer Period Register bits Value 0 - 255 Description The timer restarts at `0' when TxTMR reaches TxPR value (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 388 PIC16(L)F18424/44 Timer2 Module 26.9.3 TxCON Name: Offset: TxCON 0x28E,0x294,0x29A Timerx Control Register Bit 7 6 ON Access Reset 5 4 3 2 CKPS[2:0] 1 0 OUTPS[3:0] R/W/HC R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bit 7 - ON Timer On bit(1) Value 1 0 Description Timer is on Timer is off: all counters and state machines are reset Bits 6:4 - CKPS[2:0] Timer Clock Prescale Select bits Value 111 110 101 100 011 010 001 000 Description 1:128 Prescaler 1:64 Prescaler 1:32 Prescaler 1:16 Prescaler 1:8 Prescaler 1:4 Prescaler 1:2 Prescaler 1:1 Prescaler Bits 3:0 - OUTPS[3:0] Timer Output Postscaler Select bits Value 1111 1110 1101 1100 1011 1010 1001 1000 0111 0110 0101 0100 0011 0010 Description 1:16 Postscaler 1:15 Postscaler 1:14 Postscaler 1:13 Postscaler 1:12 Postscaler 1:11 Postscaler 1:10 Postscaler 1:9 Postscaler 1:8 Postscaler 1:7 Postscaler 1:6 Postscaler 1:5 Postscaler 1:4 Postscaler 1:3 Postscaler (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 389 PIC16(L)F18424/44 Timer2 Module Value 0001 0000 Description 1:2 Postscaler 1:1 Postscaler Note: 1. In certain modes, the ON bit will be auto-cleared by hardware. See Table 26-3. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 390 PIC16(L)F18424/44 Timer2 Module 26.9.4 TxHLT Name: Offset: TxHLT 0x28F,0x295,0x29B Timer Hardware Limit Control Register Bit Access Reset 7 6 5 PSYNC CPOL CSYNC 4 3 R/W R/W R/W R/W R/W 0 0 0 0 0 2 1 0 R/W R/W R/W 0 0 0 MODE[4:0] Bit 7 - PSYNC Timer Prescaler Synchronization Enable bit(1, 2) Value 1 0 Description Timer Prescaler Output is synchronized to FOSC/4 Timer Prescaler Output is not synchronized to FOSC/4 Bit 6 - CPOL Timer Clock Polarity Selection bit(3) Value 1 0 Description Falling edge of input clock clocks timer/prescaler Rising edge of input clock clocks timer/prescaler Bit 5 - CSYNC Timer Clock Synchronization Enable bit(4, 5) Value 1 0 Description ON bit is synchronized to timer clock input ON bit is not synchronized to timer clock input Bits 4:0 - MODE[4:0] Timer Control Mode Selection bits(6, 7) Value Description 00000 to See Table 26-3 11111 Note: 1. Setting this bit ensures that reading TxTMR will return a valid data value. 2. When this bit is `1', Timer cannot operate in Sleep mode. 3. CKPOL should not be changed while ON = 1. 4. 5. Setting this bit ensures glitch-free operation when the ON is enabled or disabled. When this bit is set then the timer operation will be delayed by two input clocks after the ON bit is set. Unless otherwise indicated, all modes start upon ON = 1 and stop upon ON = 0 (stops occur without affecting the value of TxTMR). 6. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 391 PIC16(L)F18424/44 Timer2 Module 7. When TxTMR = TxPR, the next clock clears TxTMR, regardless of the operating mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 392 PIC16(L)F18424/44 Timer2 Module 26.9.5 TxCLKCON Name: Offset: TxCLKCON 0x290,0x296,0x29C Timer Clock Source Selection Register Bit 7 6 5 4 3 2 1 0 CS[3:0] Access Reset R/W R/W R/W R/W 0 0 0 0 Bits 3:0 - CS[3:0] Timer Clock Source Selection bits Value n Description See Clock Source Selection table (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 393 PIC16(L)F18424/44 Timer2 Module 26.9.6 TxRST Name: Offset: TxRST 0x291,0x297,0x29D Timer External Reset Signal Selection Register Bit 7 6 5 4 3 2 1 0 RSEL[3:0] Access Reset R/W R/W R/W R/W 0 0 0 0 Bits 3:0 - RSEL[3:0] External Reset Source Selection Bits Value n Description See External Reset Sources table (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 394 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module 27. (ZCD) Zero-Cross Detection Module The ZCD module detects when an A/C signal crosses through the ground potential. The actual zero crossing threshold is the zero crossing reference voltage, ZCPINV, which is typically 0.75V above ground. The connection to the signal to be detected is through a series current-limiting resistor. The module applies a current source or sink to the ZCD pin to maintain a constant voltage on the pin, thereby preventing the pin voltage from forward biasing the ESD protection diodes. When the applied voltage is greater than the reference voltage, the module sinks current. When the applied voltage is less than the Filename: 10-000194D.vsd Title: ZERO CROSS DETECT BLOCK DIAGRAM (DEDICATED OUTPUT reference voltage, the module sources current. The current source and sinkPIN) action keeps the pin voltage Last Edit: 6/10/2016 constantFirst over the full range of the applied voltage. The ZCD module is shown in the following simplified Used: PIC16(L)F153xx Notes: block diagram. Figure 27-1. Simplified ZCD Block Diagram VPULLUP Rev. 10-000194D 6/10/2016 optional VDD - Zcpinv RPULLUP ZCDxIN RSERIES RPULLDOWN + External voltage source optional ZCD Output for other modules ZCDxPOL ZCDxOUT pin Interrupt det ZCDxINTP ZCDxINTN Set ZCDxIF flag Interrupt det The ZCD module is useful when monitoring an A/C waveform for, but not limited to, the following purposes: * A/C period measurement (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 395 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module * * * 27.1 Accurate long term time measurement Dimmer phase delayed drive Low EMI cycle switching External Resistor Selection The ZCD module requires a current-limiting resistor in series with the external voltage source. The impedance and rating of this resistor depends on the external source peak voltage. Select a resistor value that will drop all of the peak voltage when the current through the resistor is nominally 300 A. Make sure that the ZCD I/O pin internal weak pull-up is disabled so it does not interfere with the current source and sink. Equation 27-1. External Resistor = 3 x 10-4 Figure 27-3. External Voltage Source Rev. 30-000001A 7/18/2017 VPEAK VMAXPEAK VMINPEAK Z CPINV 27.2 ZCD Logic Output The ZCD module includes a Status bit, which can be read to determine whether the current source or sink is active. The OUT bit is set when the current sink is active, and cleared when the current source is active. The OUT bit is affected by the polarity bit. The OUT signal can also be used as input to other modules. This is controlled by the registers of the corresponding module. OUT can be used as follows: * * * 27.3 Gate source for TMR1/3/5 Clock source for TMR2/4/6 Reset source for TMR2/4/6 ZCD Logic Polarity The POL bit inverts the OUT bit relative to the current source and sink output. When the POL bit is set, a OUT high indicates that the current source is active, and a low output indicates that the current sink is active. The POL bit affects the ZCD interrupts. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 396 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module 27.4 ZCD Interrupts An interrupt will be generated upon a change in the ZCD logic output when the appropriate interrupt enables are set. A rising edge detector and a falling edge detector are present in the ZCD for this purpose. The ZCDIF bit of the PIRx register will be set when either edge detector is triggered and its associated enable bit is set. The INTP enables rising edge interrupts and the INTN bit enables falling edge interrupts. Priority of the interrupt can be changed if the IPEN bit of the INTCON register is set. The ZCD interrupt can be made high or low priority by setting or clearing the ZCDIP bit of the IPRx register. To fully enable the interrupt, the following bits must be set: * * * * ZCDIE bit of the PIEx register INTP bit for rising edge detection INTN bit for falling edge detection PEIE and GIE bits of the INTCON register Changing the POL bit will cause an interrupt, regardless of the level of the SEN bit. The ZCDIF bit of the PIRx register must be cleared in software as part of the interrupt service. If another edge is detected while this flag is being cleared, the flag will still be set at the end of the sequence. Related Links INTCON PIR2 27.5 Correction for ZCPINV Offset The actual voltage at which the ZCD switches is the reference voltage at the non-inverting input of the ZCD op amp. For external voltage source waveforms other than square waves, this voltage offset from zero causes the zero-cross event to occur either too early or too late. 27.5.1 Correction by AC Coupling When the external voltage source is sinusoidal, the effects of the ZCPINV offset can be eliminated by isolating the external voltage source from the ZCD pin with a capacitor, in addition to the voltage reducing resistor. The capacitor will cause a phase shift resulting in the ZCD output switch in advance of the actual zero crossing event. The phase shift will be the same for both rising and falling zero crossings, which can be compensated for by either delaying the CPU response to the ZCD switch by a timer or other means, or selecting a capacitor value large enough that the phase shift is negligible. To determine the series resistor and capacitor values for this configuration, start by computing the impedance, Z, to obtain a peak current of 300 A. Next, arbitrarily select a suitably large non-polar capacitor and compute its reactance, Xc, at the external voltage source frequency. Finally, compute the series resistor, capacitor peak voltage, and phase shift by the formulas shown below. When this technique is used and the input signal is not present, the ZCD will tend to oscillate. To avoid this oscillation, connect the ZCD pin to VDD or GND with a high-impedance resistor such as 200K. Equation 27-2. R-C Equations VPEAK = external voltage source peak voltage f = external voltage source frequency (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 397 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module C = series capacitor R = series resistor VC = Peak capacitor voltage = Capacitor induced zero crossing phase advance in radians T = Time ZC event occurs before actual zero crossing = 3 x 10-4 = = 1 2 2 - 2 = 3 x 10-4 = tan -1 = 2 Equation 27-3. R-C Calcuation Example = 120 = x 2 = 169.7 = 60 = 0.1 = 3 x 10-4 = = = 169.7 = 565.7 3 x 10-4 1 1 = = 26.53 2 2 x 60 x 10-7 2 - 2 = 565.1 = 560 = 2 + 2 = 560.6 = = 302.7 x 10-6 = x = 8.0 = tan -1 = 0.047 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 398 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module = 27.5.2 = 125.6 2 Correction By Offset Current When the waveform is varying relative to VSS, then the zero cross is detected too early as the waveform falls and too late as the waveform rises. When the waveform is varying relative to VDD, then the zero cross is detected too late as the waveform rises and too early as the waveform falls. The actual offset time can be determined for sinusoidal waveforms with the corresponding equations shown below. Equation 27-4. ZCD Event Offset When External Voltage source is relative to VSS = sin-1 2 When External Voltage source is relative to VDD = sin-1 - 2 This offset time can be compensated for by adding a pull-up or pull-down biasing resistor to the ZCD pin. A pull-up resistor is used when the external voltage source is varying relative to VSS. A pull-down resistor is used when the voltage is varying relative to VDD. The resistor adds a bias to the ZCD pin so that the target external voltage source must go to zero to pull the pin voltage to the ZCPINV switching voltage. The pull-up or pull-down value can be determined with the equations shown below. Equation 27-5. ZCD Pull-up/Pull-down Resistor When External Voltage source is relative to VSS = - When External Voltage source is relative to VDD = 27.6 - Handling VPEAK Variations If the peak amplitude of the external voltage is expected to vary, the series resistor must be selected to keep the ZCD current source and sink below the design maximum range of 600 A and above a reasonable minimum range. A general rule of thumb is that the maximum peak voltage can be no more than six times the minimum peak voltage. To ensure that the maximum current does not exceed 600 A and the minimum is at least 100 A, compute the series resistance as shown in Equation 27-6. The compensating pull-up for this series resistance can be determined with the equations shown in Equation 27-5 because the pull-up value is independent from the peak voltage. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 399 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module Equation 27-6. Series R for V range _ + _ = 7 x 10-4 27.7 Operation During Sleep The ZCD current sources and interrupts are unaffected by Sleep. 27.8 Effects of a Reset The ZCD circuit can be configured to default to the active or inactive state on Power-on Reset (POR). When the ZCD Configuration bit is cleared, the ZCD circuit will be active at POR. When the ZCD Configuration bit is set, the SEN bit must be set to enable the ZCD module. 27.9 Disabling the ZCD Module The ZCD module can be disabled in two ways: 1. 2. The ZCD Configuration bit disables the ZCD module when set. When this is the case then the ZCD module will be enabled by setting the SEN bit. When the ZCD bit is clear, the ZCD is always enabled and the SEN bit has no effect. The ZCD can also be disabled using the ZCDMD bit of the PMDx register. This is subject to the status of the ZCD bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 400 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module 27.10 Register Summary: ZCD Control Offset Name Bit Pos. 0x091F ZCDCON 7:0 27.11 SEN OUT POL INTP INTN Register Definitions: ZCD Control Long bit name prefixes for the ZCD peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 27-1. ZCD Long Bit Name Prefixes Peripheral Bit Name Prefix ZCD ZCD Related Links Long Bit Names Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 401 PIC16(L)F18424/44 (ZCD) Zero-Cross Detection Module 27.11.1 ZCDCON Name: Offset: ZCDCON 0x91F Zero-Cross Detect Control Register Bit 7 Access Reset 5 4 1 0 SEN 6 OUT POL 3 2 INTP INTN R/W RO R/W R/W R/W 0 x 0 0 0 Bit 7 - SEN Zero-Cross Detect Software Enable bit This bit is ignored when ZCD fuse is cleared. Value X 1 0 Condition Description ZCD Config fuse = 0 Zero-cross detect is always enabled. ZCD. This bit is ignored. source and sink current. ZCD Config fuse = 1 Zero-cross detect is enabled. ZCD pin is forced to output to source and sink current. ZCD Config fuse = 1 Zero-cross detect is disabled. ZCD pin operates according to PPS and TRIS controls. Bit 5 - OUT Zero-Cross Detect Data Output bit Value 1 0 1 0 Condition POL = 0 POL = 0 POL = 1 POL = 1 Description ZCD pin is sinking current ZCD pin is sourcing current ZCD pin is sourcing current ZCD pin is sinking current Bit 4 - POL Zero-Cross Detect Polarity bit Value 1 0 Description ZCD logic output is inverted ZCD logic output is not inverted Bit 1 - INTP Zero-Cross Detect Positive-Going Edge Interrupt Enable bit Value 1 0 Description ZCDIF bit is set on low-to-high ZCD_output transition ZCDIF bit is unaffected by low-to-high ZCD_output transition Bit 0 - INTN Zero-Cross Detect Negative-Going Edge Interrupt Enable bit Value 1 0 Description ZCDIF bit is set on high-to-low ZCD_output transition ZCDIF bit is unaffected by high-to-low ZCD_output transition (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 402 PIC16(L)F18424/44 CCP/PWM Timer Resource Selection 28. CCP/PWM Timer Resource Selection Each CCP/PWM module has an independent timer selection which can be accessed using the CxTSEL or PxTSEL bits in the CCPTMRS0 and/or CCPTMRS1 registers. The default timer selection is TMR1 when using Capture/Compare mode and T2TMR when using PWM mode in the CCPx module. The default timer selection for the PWM module is always T2TMR. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 403 PIC16(L)F18424/44 CCP/PWM Timer Resource Selection 28.1 Register Summary - Timer Selection Registers for CCP/PWM Offset Name Bit Pos. 0x021E CCPTMRS0 7:0 0x021F CCPTMRS1 7:0 28.2 C4TSEL[1:0] C3TSEL[1:0] C2TSEL[1:0] P7TSEL[1:0] P6TSEL[1:0] C1TSEL[1:0] Register Definitions: CCP/PWM Timer Selection (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 404 PIC16(L)F18424/44 CCP/PWM Timer Resource Selection 28.2.1 CCPTMRS0 Name: Offset: CCPTMRS0 0x21E CCP Timers Selection Register0 Bit 7 6 5 C4TSEL[1:0] Access Reset 4 3 C3TSEL[1:0] 2 1 C2TSEL[1:0] 0 C1TSEL[1:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 1 0 1 0 1 0 1 Bits 0:1, 2:3, 4:5, 6:7 - CxTSEL CCPx Timer Selection bits Value 11 10 01 00 Description CCPx is based off Timer5 in Capture/Compare mode and Timer6 in PWM mode CCPx is based off Timer3 in Capture/Compare mode and Timer4 in PWM mode CCPx is based off Timer1 in Capture/Compare mode and Timer2 in PWM mode Reserved (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 405 PIC16(L)F18424/44 CCP/PWM Timer Resource Selection 28.2.2 CCPTMRS1 Name: Offset: CCPTMRS1 0x21F CCP Timers Control Register Bit 7 6 5 4 3 P7TSEL[1:0] Access Reset 2 1 0 P6TSEL[1:0] R/W R/W R/W R/W 0 1 0 1 Bits 2:3, 4:5 - PxTSEL PWMx Timer Selection bits Value 11 10 01 00 Description PWMx based on TMR6 PWMx based on TMR4 PWMx based on TMR2 Reserved (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 406 PIC16(L)F18424/44 Capture/Compare/PWM Module 29. Capture/Compare/PWM Module The Capture/Compare/PWM module is a peripheral that allows the user to time and control different events, and to generate Pulse-Width Modulation (PWM) signals. In Capture mode, the peripheral allows the timing of the duration of an event. The Compare mode allows the user to trigger an external event when a predetermined amount of time has expired. The PWM mode can generate Pulse-Width Modulated signals of varying frequency and duty cycle. This family of devices contains four standard Capture/Compare/PWM modules (CCP1, CCP2, CCP3, and CCP4). It should be noted that the Capture/Compare mode operation is described with respect to TMR1 and the PWM mode operation is described with respect to T2TMR in the following sections. The Capture and Compare functions are identical for all CCP modules. Important: 1. In devices with more than one CCP module, it is very important to pay close attention to the register names used. A number placed after the module acronym is used to distinguish between separate modules. For example, the CCP1CON and CCP2CON control the same operational aspects of two completely different CCP modules. 2. Throughout this section, generic references to a CCP module in any of its operating modes may be interpreted as being equally applicable to CCPx module. Register names, module signals, I/O pins, and bit names may use the generic designator `x' to indicate the use of a numeral to distinguish a particular module, when required. 29.1 CCP Module Configuration Each Capture/Compare/PWM module is associated with a control register (CCPxCON), a capture input selection register (CCPxCAP) and a data register (CCPRx). The data register, in turn, is comprised of two 8-bit registers: CCPRxL (low byte) and CCPRxH (high byte). 29.1.1 CCP Modules and Timer Resources The CCP modules utilize Timers 1 through 6 that vary with the selected mode. Various timers are available to the CCP modules in Capture, Compare or PWM modes, as shown in the table below. Table 29-1. CCP Mode - Timer Resources CCP Mode Capture Compare PWM Timer Resource Timer1, Timer3 or Timer5 Timer2, Timer4 or Timer6 The assignment of a particular timer to a module is determined by the timer to CCP enable bits in the CCPTMRS0 and/or CCPTMRS1 registers. All of the modules may be active at once and may share the same timer resource if they are configured to operate in the same mode (Capture/Compare or PWM) at the same time. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 407 PIC16(L)F18424/44 Capture/Compare/PWM Module 29.1.2 Open-Drain Output Option When operating in Output mode (the Compare or PWM modes), the drivers for the CCPx pins can be optionally configured as open-drain outputs. This feature allows the voltage level on the pin to be pulled to a higher level through an external pull-up resistor and allows the output to communicate with external circuits without the need for additional level shifters. 29.2 Capture Mode Capture mode makes use of the 16-bit odd numbered timer resources (Timer1, Timer3, etc.). When an event occurs on the capture source, the 16-bit CCPRx register captures and stores the 16-bit value of the TMRx register. An event is defined as one of the following and is configured by the MODE bits: * * * * * Every falling edge of CCPx input Every rising edge of CCPx input Every 4th rising edge of CCPx input Every 16th rising edge of CCPx input Every edge of CCPx input (rising or falling) When a capture is made, the Interrupt Request Flag bit CCPxIF of the PIRx register is set. The interrupt flag must be cleared in software. If another capture occurs before the value in the CCPRx register is read, the old captured value is overwritten by the new captured value. Important: If an event occurs during a 2-byte read, the high and low-byte data will be from different events. It is recommended while reading the CCPRxH:CCPRxL register pair to either disable the module or read the register pair twice for data integrity. The following figure shows a simplified diagram of the capture operation. Figure 29-1. Capture Mode Operation Block Diagram Rev. 10-000158E 6/26/2017 RxyPPS CCPx PPS CTS TRIS Control CCPRxH Capture Trigger Sources See CCPxCAP register Prescaler 1,4,16 and Edge Detect CCPRxL 16 set CCPxIF 16 CCPx PPS MODE <3:0> TMR1H TMR1L CCPxPPS 29.2.1 Capture Sources In Capture mode, the CCPx pin should be configured as an input by setting the associated TRIS control bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 408 PIC16(L)F18424/44 Capture/Compare/PWM Module Important: If the CCPx pin is configured as an output, a write to the port can cause a capture condition. The capture source is selected by configuring the CTS bits as shown in the following table: Table 29-2. Capture Trigger Sources CTS 29.2.2 Source 111 CLC4_out 110 CLC3_out 101 CLC2_out 100 CLC1_out 011 IOC_interrupt 010 C2_out 001 C1_out 000 Pin selected by CCPxPPS Timer1 Mode Resource Timer1 must be running in Timer mode or Synchronized Counter mode for the CCP module to use the capture feature. In Asynchronous Counter mode, the capture operation may not work. See section "Timer1 Module with Gate Control" for more information on configuring Timer1. Related Links Timer1 Module with Gate Control 29.2.3 Software Interrupt Mode When the Capture mode is changed, a false capture interrupt may be generated. The user should keep the CCPxIE Interrupt Priority bit of the PIEx register clear to avoid false interrupts. Additionally, the user should clear the CCPxIF interrupt flag bit of the PIRx register following any change in Operating mode. Important: Clocking Timer1 from the system clock (FOSC) should not be used in Capture mode. In order for Capture mode to recognize the trigger event on the CCPx pin, Timer1 must be clocked from the instruction clock (FOSC/4) or from an external clock source. 29.2.4 CCP Prescaler There are four prescaler settings specified by the MODE bits. Whenever the CCP module is turned off, or the CCP module is not in Capture mode, the prescaler counter is cleared. Any Reset will clear the prescaler counter. Switching from one capture prescaler to another does not clear the prescaler and may generate a false interrupt. To avoid this unexpected operation, turn the module off by clearing the CCPxCON register before changing the prescaler. The example below demonstrates the code to perform this function. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 409 PIC16(L)F18424/44 Capture/Compare/PWM Module Changing Between Capture Prescalers BANKSEL CLRF MOVLW MOVWF 29.2.5 CCP1CON CCP1CON NEW_CAPT_PS CCP1CON ;(only needed when CCP1CON is not in ACCESS space) ;Turn CCP module off ;CCP ON and Prescaler select W ;Load CCP1CON with this value Capture During Sleep Capture mode depends upon the Timer1 module for proper operation. There are two options for driving the Timer1 module in Capture mode. It can be driven by the instruction clock (FOSC/4), or by an external clock source. When Timer1 is clocked by FOSC/4, Timer1 will not increment during Sleep. When the device wakes from Sleep, Timer1 will continue from its previous state. Capture mode will operate during Sleep when Timer1 is clocked by an external clock source. 29.3 Compare Mode The Compare mode function described in this section is available and identical for all CCP modules. Compare mode makes use of the 16-bit odd numbered Timer resources (Timer1, Timer3, etc.). The 16-bit value of the CCPRx register is constantly compared against the 16-bit value of the TMRx register. When a match occurs, one of the following events can occur: * * * * * * Toggle the CCPx output and clear TMRx Toggle the CCPx output without clearing TMRx Set the CCPx output Clear the CCPx output Pulse output Pulse output and clear TMRx The action on the pin is based on the value of the MODE control bits. At the same time, the interrupt flag CCPxIF bit is set, and an ADC conversion can be triggered, if selected. All Compare modes can generate an interrupt and trigger an ADC conversion. When MODE = '0001' or '1011', the CCP resets the TMRx register. The following figure shows a simplified diagram of the compare operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 410 PIC16(L)F18424/44 Capture/Compare/PWM Module Figure 29-2. Compare Mode Operation Block Diagram Rev. 30-000133A 6/27/2017 MODE Auto-conversion Trigger 4 CCPx Q PPS RxyPPS S R CCPRxH CCPRxL Output Logic Comparator TMR1H TRIS TMR1L Set CCPxIF Interrupt Flag 29.3.1 CCPx Pin Configuration The software must configure the CCPx pin as an output by clearing the associated TRIS bit and defining the appropriate output pin through the RxyPPS registers. See section "Peripheral Pin Select (PPS) Module" for more details. The CCP output can also be used as an input for other peripherals. Important: Clearing the CCPxCON register will force the CCPx compare output latch to the default low level. This is not the PORT I/O data latch. Related Links (PPS) Peripheral Pin Select Module 29.3.2 Timer1 Mode Resource In Compare mode, Timer1 must be running in either Timer mode or Synchronized Counter mode. The compare operation may not work in Asynchronous Counter mode. See Section "Timer1 Module with Gate Control" for more information on configuring Timer1. Important: Clocking Timer1 from the system clock (FOSC) should not be used in Compare mode. In order for Compare mode to recognize the trigger event on the CCPx pin, Timer1 must be clocked from the instruction clock (FOSC/4) or from an external clock source. 29.3.3 Auto-Conversion Trigger All CCPx modes set the CCP Interrupt Flag (CCPxIF). When this flag is set and a match occurs, an autoconversion trigger can take place if the CCP module is selected as the conversion trigger source. Refer to Section "Auto-Conversion Trigger" for more information. Important: Removing the match condition by changing the contents of the CCPRxH and CCPRxL register pair, between the clock edge that generates the Auto-conversion Trigger and the clock edge that generates the Timer1 Reset, will preclude the Reset from occurring. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 411 PIC16(L)F18424/44 Capture/Compare/PWM Module Related Links Auto-Conversion Trigger 29.3.4 Compare During Sleep Since FOSC is shut down during Sleep mode, the Compare mode will not function properly during Sleep, unless the timer is running. The device will wake on interrupt (if enabled). 29.4 PWM Overview Pulse-Width Modulation (PWM) is a scheme that provides power to a load by switching quickly between fully ON and fully OFF states. The PWM signal resembles a square wave where the high portion of the signal is considered the ON state and the low portion of the signal is considered the OFF state. The high portion, also known as the pulse width, can vary in time and is defined in steps. A larger number of steps applied, which lengthens the pulse width, also supplies more power to the load. Lowering the number of steps applied, which shortens the pulse width, supplies less power. The PWM period is defined as the duration of one complete cycle or the total amount of ON and OFF time combined. PWM resolution defines the maximum number of steps that can be present in a single PWM period. A higher resolution allows for more precise control of the pulse-width time and in turn the power that is applied to the load. The term duty cycle describes the proportion of the ON time to the OFF time and is expressed in percentages, where 0% is fully OFF and 100% is fully ON. A lower duty cycle corresponds to less power applied and a higher duty cycle corresponds to more power applied. The shows a typical waveform of the PWM signal. Figure 29-3. CCP PWM Output Signal Rev. 30-000134A 5/9/2017 Period Pulse Width TMR2 = PR2 TMR2 = CCPRxH:CCPRxL TMR2 = 0 29.4.1 Standard PWM Operation The standard PWM function described in this section is available and identical for all CCP modules. The standard PWM mode generates a Pulse-Width Modulation (PWM) signal on the CCPx pin with up to ten bits of resolution. The period, duty cycle, and resolution are controlled by the following registers: * * * * Even numbered TxPR registers (T2PR, T4PR, etc) Even numbered TxCON registers (T2CON, T4CON, etc) 16-bit CCPRx registers CCPxCON registers It is required to have FOSC/4 as the clock input to TxTMR for correct PWM operation. The following figure shows a simplified block diagram of PWM operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 412 PIC16(L)F18424/44 Capture/Compare/PWM Module Figure 29-4. Simplified PWM Block Diagram Rev. 10-000 157C 9/5/201 4 Duty cycle registers CCPRxH CCPRxL CCPx_out 10-bit Latch(2) (Not accessible by user) Comparator R S Q PPS RxyPPS TMR2 Module R TMR2 To Peripherals set CCPIF CCPx TRIS Control (1) ERS logic Comparator CCPx_pset PR2 Note: 1. 8-bit timer is concatenated with two bits generated by FOSC or two bits of the internal prescaler to create 10-bit time base. 2. The alignment of the 10 bits from the CCPRx register is determined by the CCPxFMT bit. Important: The corresponding TRIS bit must be cleared to enable the PWM output on the CCPx pin. 29.4.2 Setup for PWM Operation The following steps should be taken when configuring the CCP module for standard PWM operation: 1. 2. 3. 4. 5. Use the desired output pin RxyPPS control to select CCPx as the source and disable the CCPx pin output driver by setting the associated TRIS bit. Load the T2PR register with the PWM period value. Configure the CCP module for the PWM mode by loading the CCPxCON register with the appropriate values. Load the CCPRx register with the PWM duty cycle value and configure the FMT bit to set the proper register alignment. Configure and start Timer2: - Clear the TMR2IF interrupt flag bit of the PIRx register. See Note below. - Select the timer clock source to be as FOSC/4 using the TxCLKCON register. This is required for correct operation of the PWM module. - Configure the T2CKPS bits of the T2CON register with the timer prescale value. - Enable the timer by setting the T2ON bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 413 PIC16(L)F18424/44 Capture/Compare/PWM Module 6. Enable PWM output pin: - Wait until the timer overflows and the TMR2IF bit of the PIRx register is set. See Note below. - Enable the CCPx pin output driver by clearing the associated TRIS bit. Important: In order to send a complete duty cycle and period on the first PWM output, the above steps must be included in the setup sequence. If it is not critical to start with a complete PWM signal on the first output, then step 6 may be ignored. Related Links TxCON 29.4.3 Timer2 Timer Resource The PWM standard mode makes use of the 8-bit Timer2 timer resources to specify the PWM period. 29.4.4 PWM Period The PWM period is specified by the T2PR register of Timer2. The PWM period can be calculated using the formula in the equation below. Equation 29-1. PWM Period = 2 + 1 * 4 * * 2Pr where TOSC = 1/FOSC When T2TMR is equal to T2PR, the following three events occur on the next increment cycle: * * * T2TMR is cleared The CCPx pin is set. (Exception: If the PWM duty cycle = 0%, the pin will not be set.) The PWM duty cycle is transferred from the CCPRx register into a 10-bit buffer. Important: The Timer postscaler (see "Timer2 Interrupt") is not used in the determination of the PWM frequency. Related Links Timer2 Interrupt 29.4.5 PWM Duty Cycle The PWM duty cycle is specified by writing a 10-bit value to the CCPRx register. The alignment of the 10bit value is determined by the FMT bit (see Figure 29-6). The CCPRx register can be written to at any time. However, the duty cycle value is not latched into the 10-bit buffer until after a match between T2PR and T2TMR. The equations below are used to calculate the PWM pulse width and the PWM duty cycle ratio. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 414 PIC16(L)F18424/44 Capture/Compare/PWM Module Figure 29-6. PWM 10-Bit Alignment Rev. 10-000 160A 12/9/201 3 CCPRxH CCPRxL 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 FMT = 1 FMT = 0 CCPRxH CCPRxL 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 10-bit Duty Cycle 9 8 7 6 5 4 3 2 1 0 Equation 29-2. Pulse Width = : * * 2 Pr Equation 29-3. Duty Cycle : = 4 2 + 1 The CCPRx register is used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. The 8-bit timer T2TMR register is concatenated with either the 2-bit internal system clock (FOSC), or two bits of the prescaler, to create the 10-bit time base. The system clock is used if the Timer2 prescaler is set to 1:1. When the 10-bit time base matches the CCPRx register, then the CCPx pin is cleared (see Figure 29-4). 29.4.6 PWM Resolution The resolution determines the number of available duty cycles for a given period. For example, a 10-bit resolution will result in 1024 discrete duty cycles, whereas an 8-bit resolution will result in 256 discrete duty cycles. The maximum PWM resolution is ten bits when T2PR is 255. The resolution is a function of the T2PR register value as shown below. Equation 29-4. PWM Resolution log 4 2 + 1 Re = log 2 Important: If the pulse-width value is greater than the period, the assigned PWM pin(s) will remain unchanged. Table 29-3. Example PWM Frequencies and Resolutions (FOSC = 20 MHz) PWM Frequency Timer Prescale T2PR Value Maximum Resolution (bits) (c) 2018 Microchip Technology Inc. 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz 16 4 1 1 1 1 0xFF 0xFF 0xFF 0x3F 0x1F 0x17 10 10 10 8 7 6.6 Datasheet Preliminary DS40002000A-page 415 PIC16(L)F18424/44 Capture/Compare/PWM Module Table 29-4. Example PWM Frequencies and Resolutions (FOSC = 8 MHz) PWM Frequency Timer Prescale T2PR Value Maximum Resolution (bits) 1.22 kHz 4.90 kHz 19.61 kHz 76.92 kHz 153.85 kHz 200.0 kHz 16 4 1 1 1 1 0x65 0x65 0x65 0x19 0x0C 0x09 8 8 8 6 5 5 29.4.7 Operation in Sleep Mode In Sleep mode, the T2TMR register will not increment and the state of the module will not change. If the CCPx pin is driving a value, it will continue to drive that value. When the device wakes up, T2TMR will continue from the previous state. 29.4.8 Changes in System Clock Frequency The PWM frequency is derived from the system clock frequency. Any changes in the system clock frequency will result in changes to the PWM frequency. See the "Oscillator Module (with Fail-Safe Clock Monitor)" section for additional details. Related Links Oscillator Module (with Fail-Safe Clock Monitor) 29.4.9 Effects of Reset Any Reset will force all ports to Input mode and the CCP registers to their Reset states. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 416 PIC16(L)F18424/44 Capture/Compare/PWM Module 29.5 Register Summary - CCP Control Offset Name Bit Pos. 0x030C CCPR1 0x030E CCP1CON 7:0 0x030F CCP1CAP 7:0 7:0 15:8 CCPRH[7:0] EN OUT FMT MODE[3:0] CTS[2:0] 7:0 CCPRL[7:0] 15:8 CCPRH[7:0] 0x0310 CCPR2 0x0312 CCP2CON 7:0 0x0313 CCP2CAP 7:0 EN OUT CCPR3 0x0316 CCP3CON 7:0 0x0317 CCP3CAP 7:0 FMT MODE[3:0] CTS[2:0] 7:0 0x0314 CCPRL[7:0] 15:8 CCPRH[7:0] EN OUT FMT MODE[3:0] CTS[2:0] 7:0 CCPRL[7:0] 15:8 CCPRH[7:0] 0x0318 CCPR4 0x031A CCP4CON 7:0 0x031B CCP4CAP 7:0 29.6 CCPRL[7:0] EN OUT FMT MODE[3:0] CTS[2:0] Register Definitions: CCP Control Long bit name prefixes for the CCP peripherals are shown in the following table. Refer to the "Long Bit Names" section for more information. Table 29-5. CCP Long Bit Name Prefixes Peripheral Bit Name Prefix CCP1 CCP1 CCP2 CCP2 CCP3 CCP3 CCP4 CCP4 Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 417 PIC16(L)F18424/44 Capture/Compare/PWM Module 29.6.1 CCPxCON Name: Offset: CCPxCON 0x30E,0x312,0x316,0x31A CCP Control Register Bit Access Reset 5 4 EN 7 6 OUT FMT 3 R/W RO R/W R/W 0 x 0 0 2 1 0 R/W R/W R/W 0 0 0 MODE[3:0] Bit 7 - EN CCP Module Enable bit Value 1 0 Description CCP is enabled CCP is disabled Bit 5 - OUT CCP Output Data bit (read-only) Bit 4 - FMT CCPW (pulse-width) Value Alignment bit Value x x 1 0 Condition Capture mode Compare mode PWM mode PWM mode Description Not used Not used Left-aligned format Right-aligned format Bits 3:0 - MODE[3:0] CCP Mode Select bits Table 29-6. CCPx Mode Select Bits MODE Operating Mode Operation Set CCPxIF 11xx PWM PWM Operation Yes 1011 Compare Pulse output; clear TMR1(2) Yes 1010 Pulse output Yes 1001 Clear output(1) Yes 1000 Set output(1) Yes Every 16th rising edge of CCPx input Yes 0110 Every 4th rising edge of CCPx input Yes 0101 Every rising edge of CCPx input Yes 0100 Every falling edge of CCPx input Yes 0011 Every edge of CCPx input Yes Toggle output Yes 0111 0010 Capture Compare (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 418 PIC16(L)F18424/44 Capture/Compare/PWM Module MODE Operating Mode 0001 0000 Operation Set CCPxIF Toggle output; clear TMR1(2) Yes Disabled -- Note: 1. The set and clear operations of the Compare mode are reset by setting MODE = '0000' or EN = 0. 2. When MODE = '0001' or '1011', then the timer associated with the CCP module is cleared. TMR1 is the default selection for the CCP module, so it is used for indication purpose only. Note: 1. The set and clear operations of the Compare mode are reset by setting MODE = '0000' or EN = 0. 2. When MODE = '0001' or '1011', then the timer associated with the CCP module is cleared. TMR1 is the default selection for the CCP module, so it is used for indication purpose only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 419 PIC16(L)F18424/44 Capture/Compare/PWM Module 29.6.2 CCPxCAP Name: Offset: CCPxCAP 0x30F,0x313,0x317,0x31B Capture Trigger Input Selection Register Bit 7 6 5 4 3 2 1 0 CTS[2:0] Access Reset R/W R/W R/W 0 0 0 Bits 2:0 - CTS[2:0] Capture Trigger Input Selection bits Table 29-7. Capture Trigger Sources CTS Source 111 CLC4_out 110 CLC3_out 101 CLC2_out 100 CLC1_out 011 IOC_interrupt 010 C2_out 001 C1_out 000 Pin selected by CCPxPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 420 PIC16(L)F18424/44 Capture/Compare/PWM Module 29.6.3 CCPRx Name: Offset: CCPRx 0x30C,0x310,0x314,0x318 Capture/Compare/Pulse Width Register Bit 15 14 13 12 11 10 9 8 CCPRH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset x x x x x x x x Bit 7 6 5 4 3 2 1 0 CCPRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 15:8 - CCPRH[7:0] Capture/Compare/Pulse Width High byte Value 0 to 255 0 to 255 0,1,2,3 0 to 255 Name MODE = Capture MODE = Compare MODE = PWM & FMT=0 Description High byte of 16-bit captured value High byte of 16-bit compare value CCPRH<1:0>=Bits<9:8> of 10-bit Pulse width value MODE = PWM & FMT=1 CCPRH<7:2> not used Bits<9:2> of 10-bit Pulse width value Bits 7:0 - CCPRL[7:0] Capture/Compare/Pulse Width Low byte Value 0 to 255 0 to 255 0 to 255 0,64,128, 192 Name MODE = Capture MODE = Compare MODE = PWM & FMT=0 MODE = PWM & FMT=1 (c) 2018 Microchip Technology Inc. Description Low byte of 16-bit captured value Low byte of 16-bit compare value Bits<7:0> of 10-bit Pulse width value CCPRL<7:6>=Bits<1:0> of 10-bit Pulse width value CCPRL<5:0> not used Datasheet Preliminary DS40002000A-page 421 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation 30. (PWM) Pulse-Width Modulation The PWM module generates a Pulse-Width Modulated signal determined by the duty cycle, period, and resolution that are configured by the following registers: * * * * TxPR TxCON PWMxDC PWMxCON Important: The corresponding TRIS bit must be cleared to enable the PWM output on the PWMx pin. Each PWM module can select the timer source that controls the module. Note that the PWM mode Filename: 10-000022B.vsd operation is described with respect to TMR2 in the following sections. Title: PWM Block Diagram Last Edit: Figure 30-1 shows 9/24/2014 a simplified block diagram of PWM operation. First Used: 16(L)F1614/5/8/9 (LECW/X) Notes: Figure 30-2 shows a typical waveform of the PWM signal. Figure 30-1. Simplified PWM Block Diagram Rev. 10-000022B 9/24/2014 PWMxDCL<7:6> Duty cycle registers PWMxDCH PWMx_out 10-bit Latch (Not visible to user) Comparator R Q 0 S To Peripherals Q 1 PPS PWMx TMR2 Module TMR2 Comparator R PWMxPOL (1) RxyPPS TRIS Control T2_match PR2 Note 1: 8-bit timer is concatenated with two bits generated by Fosc or two bits of the internal prescaler to Note: create 10-bit time-base. 1. 8-bit timer is concatenated with two bits generated by Fosc or two bits of the internal prescaler to create 10-bit time base. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 422 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation Figure 30-2. PWM Output Period Rev. 30-000129A 5/17/2017 Pulse Width TMR2 = PR2 TMR2 = PWMxDCH<7:0>:PWMxDCL<7:6> TMR2 = 0 For a step-by-step procedure on how to set up this module for PWM operation, refer to Setup for PWM Operation using PWMx Output Pins. 30.1 Fundamental Operation The PWM module produces a 10-bit resolution output. The PWM timer can be selected using the PxTSEL bits in the CCPTMRS register. The default selection for PWMx is TMR2. Note that the PWM module operation in the following sections is described with respect to TMR2. Timer2 and T2PR set the period of the PWM. The PWMxDCL and PWMxDCH registers configure the duty cycle. The period is common to all PWM modules, whereas the duty cycle is independently controlled. Important: The Timer2 postscaler is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. All PWM outputs associated with Timer2 are set when T2TMR is cleared. Each PWMx is cleared when TxTMR is equal to the value specified in the corresponding PWMxDCH (8 MSb) and PWMxDCL<7:6> (2 LSb) registers. When the value is greater than or equal to T2PR, the PWM output is never cleared (100% duty cycle). Important: The PWMxDCH and PWMxDCL registers are double buffered. The buffers are updated when T2TMR matches T2PR. Care should be taken to update both registers before the timer match occurs. 30.2 PWM Output Polarity The output polarity is inverted by setting the POL bit. 30.3 PWM Period The PWM period is specified by the TxPR register The PWM period can be calculated using the formula of PWM Period. It is required to have FOSC/4 as the selected clock input to the timer for correct PWM operation. Equation 30-1. PWM Period = 2 + 1 * 4 * * 2 Pr Note: TOSC = 1/FOSC When T2TMR is equal to T2PR, the following three events occur on the next increment cycle: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 423 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation * * * T2TMR is cleared The PWM output is active. (Exception: When the PWM duty cycle = 0%, the PWM output will remain inactive.) The PWMxDCH and PWMxDCL register values are latched into the buffers. Important: The Timer2 postscaler has no effect on the PWM operation. 30.4 PWM Duty Cycle The PWM duty cycle is specified by writing a 10-bit value to the PWMxDCH and PWMxDCL register pair. The PWMxDCH register contains the eight MSbs and the PWMxDCL<7:6>, the two LSbs. The PWMxDCH and PWMxDCL registers can be written to at any time. The formulas below are used to calculate the PWM pulse width and the PWM duty cycle ratio. Equation 30-2. Pulse Width = : < 7: 6 > * * 2Pr Note: TOSC = 1/FOSC Equation 30-3. Duty Cycle Ratio : < 7: 6 > = 4 2 + 1 The 8-bit timer T2TMR register is concatenated with the two Least Significant bits of 1/FOSC, adjusted by the Timer2 prescaler to create the 10-bit time base. The system clock is used if the Timer2 prescaler is set to 1:1. 30.5 PWM Resolution The resolution determines the number of available duty cycles for a given period. For example, a 10-bit resolution will result in 1024 discrete duty cycles, whereas an 8-bit resolution will result in 256 discrete duty cycles. The maximum PWM resolution is ten bits when T2PR is 255. The resolution is a function of the T2PR register value as shown below. Equation 30-4. PWM Resolution log 4 2 + 1 Re = log 2 Important: If the pulse-width value is greater than the period, the assigned PWM pin(s) will remain unchanged. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 424 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation Table 30-1. Example PWM Frequencies and Resolutions (Fosc = 20 MHz) PWM Frequency Timer Prescale T2PR Value Maximum Resolution (bits) 0.31 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz 64 4 1 1 1 1 0xFF 0xFF 0xFF 0x3F 0x1F 0x17 10 10 10 8 7 6.6 Table 30-2. Example PWM Frequencies and Resolutions (Fosc = 8 MHz) PWM Frequency 0.31 kHz 4.90 kHz 19.61 kHz 76.92 kHz 153.85 kHz 200.0 kHz 64 4 1 1 1 1 0x65 0x65 0x65 0x19 0x0C 0x09 8 8 8 6 5 5 Timer Prescale T2PR Value Maximum Resolution (bits) 30.6 Operation in Sleep Mode In Sleep mode, the T2TMR register will not increment and the state of the module will not change. If the PWMx pin is driving a value, it will continue to drive that value. When the device wakes up, T2TMR will continue from its previous state. 30.7 Changes in System Clock Frequency The PWM frequency is derived from the system clock frequency (FOSC). Any changes in the system clock frequency will result in changes to the PWM frequency. Related Links Oscillator Module (with Fail-Safe Clock Monitor) 30.8 Effects of Reset Any Reset will force all ports to Input mode and the PWM registers to their Reset states. 30.9 Setup for PWM Operation using PWMx Output Pins The following steps should be taken when configuring the module for PWM operation using the PWMx pins: 1. 2. 3. 4. 5. Disable the PWMx pin output driver(s) by setting the associated TRIS bit(s). Clear the PWMxCON register. Load the T2PR register with the PWM period value. Load the PWMxDCH register and bits <7:6> of the PWMxDCL register with the PWM duty cycle value. Configure and start Timer2: - Clear the TMR2IF interrupt flag bit of the PIRx register.(1) - Select the timer clock source to be as FOSC/4 using the TxCLKCON register. This is required for correct operation of the PWM module. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 425 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation 6. 7. 8. - Configure the T2CKPS bits of the T2CON register with the Timer2 prescale value. - Enable Timer2 by setting the T2ON bit of the T2CON register. Enable PWM output pin and wait until Timer2 overflows, TMR2IF bit of the PIRx register is set.(2) Enable the PWMx pin output driver(s) by clearing the associated TRIS bit(s) and setting the desired pin PPS control bits. Configure the PWM module by loading the PWMxCON register with the appropriate values. Note: 1. In order to send a complete duty cycle and period on the first PWM output, the above steps must be followed in the order given. If it is not critical to start with a complete PWM signal, then move Step 8 to replace Step 4. 2. For operation with other peripherals only, disable PWMx pin outputs. 30.9.1 PWMx Pin Configuration All PWM outputs are multiplexed with the PORT data latch. The user must configure the pins as outputs by clearing the associated TRIS bits. 30.10 Setup for PWM Operation to Other Device Peripherals The following steps should be taken when configuring the module for PWM operation to be used by other device peripherals: 1. 2. 3. 4. 5. 6. 7. Disable the PWMx pin output driver(s) by setting the associated TRIS bit(s). Clear the PWMxCON register. Load the T2PR register with the PWM period value. Load the PWMxDCH register and bits <7:6> of the PWMxDCL register with the PWM duty cycle value. Configure and start Timer2: - Clear the TMR2IF interrupt flag bit of the PIRx register.(1) - Select the timer clock source to be as FOSC/4 using the TxCLKCON register. This is required for correct operation of the PWM module. - Configure the T2CKPS bits of the T2CON register with the Timer2 prescale value. - Enable Timer2 by setting the T2ON bit of the T2CON register. Wait until Timer2 overflows, TMR2IF bit of the PIRx register is set.(1) Configure the PWM module by loading the PWMxCON register with the appropriate values. Note: 1. In order to send a complete duty cycle and period on the first PWM output, the above steps must be included in the setup sequence. If it is not critical to start with a complete PWM signal on the first output, then step 6 may be ignored. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 426 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation 30.11 Register Summary - Registers Associated with PWM Offset Name 0x038C PWM6DC 0x038E PWM6CON 0x038F Reserved 0x0390 PWM7DC 0x0392 PWM7CON 30.12 Bit Pos. 7:0 DCL[1:0] 15:8 7:0 DCH[7:0] EN 7:0 OUT POL DCL[1:0] 15:8 7:0 DCH[7:0] EN OUT POL Register Definitions: PWM Control Long bit name prefixes for the PWM peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 30-3. PWM Bit Name Prefixes Peripheral Bit Name Prefix PWM6 PWM6 PWM7 PWM7 Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 427 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation 30.12.1 PWMxCON Name: Offset: PWMxCON 0x38E,0x392 PWM Control Register Bit Access Reset 5 4 EN 7 6 OUT POL R/W RO R/W 0 0 0 3 2 1 0 Bit 7 - EN PWM Module Enable bit Value 1 0 Description PWM module is enabled PWM module is disabled Bit 5 - OUT PWM Module Output Level When Bit is Read Bit 4 - POL PWM Output Polarity Select bit Value 1 0 Description PWM output is inverted PWM output is normal (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 428 PIC16(L)F18424/44 (PWM) Pulse-Width Modulation 30.12.2 PWMxDC Name: Offset: PWMxDC 0x38C,0x390 PWM Duty Cycle Register Bit 15 14 13 12 11 10 9 8 DCH[7:0] Access Reset x Bit 7 x x x x x x x 6 5 4 3 2 1 0 DCL[1:0] Access Reset x x Bits 15:8 - DCH[7:0] PWM Duty Cycle Most Significant bits These bits are the MSbs of the PWM duty cycle. Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Bits 7:6 - DCL[1:0] PWM Duty Cycle Least Significant bits These bits are the LSbs of the PWM duty cycle. Reset States: POR/BOR = xx All Other Resets = uu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 429 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31. (CWG) Complementary Waveform Generator Module The Complementary Waveform Generator (CWG) produces half-bridge, full-bridge, and steering of PWM waveforms. It is backwards compatible with previous CCP functions. The PIC16(L)F18424/44 family has 2 instance(s) of the CWG module. The CWG has the following features: * * * * * 31.1 Six Operating modes: - Synchronous Steering mode - Asynchronous Steering mode - Full-Bridge mode, Forward - Full-Bridge mode, Reverse - Half-Bridge mode - Push-Pull mode Output Polarity Control Output Steering Independent 6-Bit Rising and Falling Event Dead-Band Timers: - Clocked dead band - Independent rising and falling dead-band enables Auto-Shutdown Control With: - Selectable shutdown sources - Auto-restart option - Auto-shutdown pin override control Fundamental Operation The CWG generates two output waveforms from the selected input source. The off-to-on transition of each output can be delayed from the on-to-off transition of the other output, thereby, creating a time delay immediately where neither output is driven. This is referred to as dead time and is covered in Dead-Band Control. It may be necessary to guard against the possibility of circuit faults or a feedback event arriving too late or not at all. In this case, the active drive must be terminated before the Fault condition causes damage. This is referred to as auto-shutdown and is covered in Auto-Shutdown. 31.2 Operating Modes The CWG module can operate in six different modes, as specified by the MODE bits: * * * * * * Half-Bridge mode Push-Pull mode Asynchronous Steering mode Synchronous Steering mode Full-Bridge mode, Forward Full-Bridge mode, Reverse (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 430 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... All modes accept a single pulse data input, and provide up to four outputs as described in the following sections. All modes include auto-shutdown control as described in Auto-Shutdown Important: Except as noted for Full-Bridge mode (Full-Bridge Modes), mode changes should only be performed while EN = 0. 31.2.1 Half-Bridge Mode In Half-Bridge mode, two output signals are generated as true and inverted versions of the input as illustrated in Figure 31-1. A non-overlap (dead-band) time is inserted between the two outputs to prevent shoot-through current in various power supply applications. Dead-band control is described in Dead-Band Control. The output steering feature cannot be used in this mode. A basic block diagram of this mode is shown in Figure 31-2. The unused outputs CWGxC and CWGxD drive similar signals, with polarity independently controlled by the POLC and POLD bits, respectively. Figure 31-1. CWG Half-Bridge Mode Operation Rev. 30-000097A 4/14/2017 CWGx_clock CWGxA CWGxC Falling Event Dead Band Rising Event Dead Band Rising Event D Falling Event Dead Band CWGxB CWGxD CWGx_data Note: CWGx_rising_src = CCP1_out, CWGx_falling_src = ~CCP1_out (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 431 Filename: Title: Last Edit: First Used: Notes: 10-000209D.vsd SIMPLIFIED CWG BLOCK DIAGRAM (HALF-BRIDGE MODE) 2/2/2016 PIC18(L)F6xK40 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Figure 31-2. Simplified CWG Block Diagram (Half-Bridge Mode, MODE<2:0> = 100) LSAC<1:0> Rev. 10-000209D 2/2/2016 `1' 00 `0' 01 High-Z 10 11 Rising Dead-Band Block CWG Clock clock CWG Data data out data in 1 CWG Data A 0 POLA CWG1A LSBD<1:0> `1' 00 `0' 01 High-Z 10 Falling Dead-Band Block clock data out CWG Data B data in 11 CWG Data CWG Data Input 1 0 POLB D CWG1B Q E LSAC<1:0> `1' 00 `0' 01 High-Z 10 EN 11 1 0 CWG1C POLC Auto-shutdown source (CWGxAS1 register) S Q LSBD<1:0> R `1' 00 `0' 01 High-Z 10 REN SHUTDOWN = 0 11 1 0 CWG1D POLD SHUTDOWN FREEZE D Q CWG Data 31.2.2 Push-Pull Mode In Push-Pull mode, two output signals are generated, alternating copies of the input as illustrated in Figure 31-3. This alternation creates the push-pull effect required for driving some transformer-based (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 432 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... power supply designs. Steering modes are not used in Push-Pull mode. A basic block diagram for the Push-Pull mode is shown in Figure 31-4. The push-pull sequencer is reset whenever EN = 0 or if an auto-shutdown event occurs. The sequencer is clocked by the first input pulse, and the first output appears on CWG1A. The unused outputs CWGxC and CWGxD drive copies of CWGxA and CWGxB, respectively, but with polarity controlled by the POLC and POLD bits of the CWGxCON1 register, respectively. Figure 31-3. CWG Push-Pull Mode Operation Rev. 30-000098A 4/14/2017 CWG1 clock Input source CWG1A CWG1B (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 433 Filename: Title: Last Edit: First Used: Notes: 10-000210D.vsd SIMPLIFIED CWG BLOCK DIAGRAM (PUSH-PULL MODE) 2/2/2016 PIC18(L)F6xK40 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Figure 31-4. Simplified CWG Block Diagram (Push-Pull Mode, MODE<2:0> = 101) LSAC<1:0> Rev. 10-000210D 2/2/2016 `1' 00 `0' 01 High-Z 10 11 CWG Data 1 CWG Data A 0 CWG1A POLA D LSBD<1:0> Q Q `1' 00 `0' 01 High-Z 10 11 CWG Data B 1 CWG Data Input CWG Data D 0 CWG1B POLB Q LSAC<1:0> E `1' 00 `0' 01 High-Z 10 EN 11 1 0 CWG1C POLC Auto-shutdown source (CWGxAS1 register) S Q LSBD<1:0> R REN `1' 00 `0' 01 High-Z 10 SHUTDOWN = 0 11 1 0 CWG1D POLD SHUTDOWN FREEZE D Q CWG Data 31.2.3 Full-Bridge Modes In Forward and Reverse Full-Bridge modes, three outputs drive static values while the fourth is modulated by the input data signal. The mode selection may be toggled between forward and reverse by toggling the MODE<0> bit of the CWGxCON0 while keeping MODE<2:1> static, without disabling the (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 434 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... CWG module. When connected, as shown in Figure 31-5, the outputs are appropriate for a full-bridge Filename: 10-000263A.vsd Title: driver. Each Example of Full-Bridge Application motor CWG output signal has independent polarity control, so the circuit can be adapted to Last Edit: 12/8/2015 high-active and low-active drivers. A simplified block diagram for the Full-Bridge modes is shown in First Used: PIC18(L)F2x/4xK40 Note: Figure 31-6. Figure 31-5. Example of Full-Bridge Application Rev. 10-000263A 12/8/2015 VDD FET Driver QA QC FET Driver CWG1A LOAD CWG1B CWG1C CWG1D (c) 2018 Microchip Technology Inc. FET Driver FET Driver QB Datasheet Preliminary QD DS40002000A-page 435 Filename: Title: Last Edit: First Used: Notes: 10-000212D.vsd SIMPLIFIED CWG BLOCK DIAGRAM (FULL-BRIDGE MODES) 2/2/2016 PIC18(L)F6xK40 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Figure 31-6. Simplified CWG Block Diagram (Forward and Reverse Full-Bridge Modes) Rev. 10-000212D 2/2/2016 MODE<2:0> = 010: Forward LSAC<1:0> MODE<2:0> = 011: Reverse Rising Dead-Band Block CWG Clock clock signal out signal in D CWG Data 00 `0' 01 High-Z 10 11 CWG Data MODE<2:0> `1' 1 CWG Data A 0 CWG1A POLA Q Q LSBD<1:0> cwg data signal in signal out clock CWG Clock `1' 00 `0' 01 High-Z 10 11 Falling Dead-Band Block CWG Data Input CWG Data 1 CWG Data B 0 CWG1B POLB D Q LSAC<1:0> E EN `1' 00 `0' 01 High-Z 10 11 1 CWG Data C Auto-shutdown source (CWGxAS1 register) 0 CWG1C POLC S Q LSBD<1:0> R REN SHUTDOWN = 0 `1' 00 `0' 01 High-Z 10 11 1 CWG Data D 0 CWG1D POLD SHUTDOWN FREEZE D Q CWG Data In Forward Full-Bridge mode (MODE = 010), CWGxA is driven to its active state, CWGxB and CWGxC are driven to their inactive state, and CWGxD is modulated by the input signal, as shown in Figure 31-7. In Reverse Full-Bridge mode (MODE = 011), CWGxC is driven to its active state, CWGxA and CWGxD are driven to their inactive states, and CWG1B is modulated by the input signal, as shown in Figure 31-7. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 436 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... In Full-Bridge mode, the dead-band period is used when there is a switch from forward to reverse or viceversa. This dead-band control is described in Dead-Band Control, with additional details in Rising Edge and Reverse Dead Band and Falling Edge and Forward Dead Band. Steering modes are not used with either of the Full-Bridge modes. The mode selection may be toggled between forward and reverse toggling the MODE<0> bit of the CWGxCON0 while keeping MODE<2:1> static, without disabling the CWG module. Figure 31-7. Example of Full-Bridge Output Rev. 30-000099A 4/14/2017 Forward Mode Period CWG1A(2) CWG1B(2) CWG1C(2) Pulse Width CWG1D(2) (1) Reverse Mode (1) Period CWG1A(2) Pulse Width CWG1B(2) CWG1C(2) CWG1D(2) (1) (1) Note: 1. A rising CWG data input creates a rising event on the modulated output. 2. Output signals shown as active-high; all POLy bits are clear. 31.2.3.1 Direction Change in Full-Bridge Mode In Full-Bridge mode, changing MODE controls the forward/reverse direction. Direction changes occur on the next rising edge of the modulated input. A direction change is initiated in software by changing the MODE bits. The sequence is illustrated in Figure 31-8. * The associated active output CWGxA and the inactive output CWGxC are switched to drive in the opposite direction. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 437 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... * * The previously modulated output CWGxD is switched to the inactive state, and the previously inactive output CWGxB begins to modulate. CWG modulation resumes after the direction-switch dead band has elapsed. 31.2.3.2 Dead-Band Delay in Full-Bridge Mode Dead-band delay is important when either of the following conditions is true: 1. 2. The direction of the CWG output changes when the duty cycle of the data input is at or near 100%, or The turn-off time of the power switch, including the power device and driver circuit, is greater than the turn-on time. The dead-band delay is inserted only when changing directions, and only the modulated output is affected. The statically-configured outputs (CWGxA and CWGxC) are not afforded dead band, and switch essentially simultaneously. The following figure shows an example of the CWG outputs changing directions from forward to reverse, at near 100% duty cycle. In this example, at time t1, the output of CWGxA and CWGxD become inactive, while output CWGxC becomes active. Since the turn-off time of the power devices is longer than the turnon time, a shoot-through current will flow through power devices QC and QD for the duration of `t'. The same phenomenon will occur to power devices QA and QB for the CWG direction change from reverse to forward. When changing the CWG direction at high duty cycle is required for an application, two possible solutions for eliminating the shoot-through current are: 1. 2. Reduce the CWG duty cycle for one period before changing directions. Use switch drivers that can drive the switches off faster than they can drive them on. Figure 31-8. Example of PWM Direction Change at Near 100% Duty Cycle Rev. 30-000100A 4/14/2017 Forward Period t1 Reverse Period CWG1A CWG1B Pulse Width CWG1C CWG1D Pulse Width TON External Switch C TOFF External Switch D Potential ShootThrough Current (c) 2018 Microchip Technology Inc. T = TOFF - TON Datasheet Preliminary DS40002000A-page 438 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.2.4 Steering Modes In both Synchronous and Asynchronous Steering modes, the modulated input signal can be steered to any combination of four CWG outputs. A fixed-value will be presented on all the outputs not used for the PWM output. Each output has independent polarity, steering, and shutdown options. Dead-band control is not used in either steering mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 439 Filename: Title: Last Edit: First Used: Notes: 10-000211D.vsd SIMPLIFIED CWG BLOCK DIAGRAM (OUTPUT STEERING MODES) 5/30/2017 PIC18(L)F6xK40 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Figure 31-9. Simplified CWG Block Diagram (Output Steering Modes) Rev. 10-000211D 5/30/2017 MODE<2:0> = 000: Asynchronous LSAC<1:0> MODE<2:0> = 001: Synchronous `1' 00 `0' 01 High-Z 10 11 CWG Data A 1 1 POLA OVRA 0 CWG1A 0 STRA CWG Data CWG Data Input LSBD<1:0> `1' 00 `0' 01 High-Z 10 11 D CWG Data B Q E 1 1 POLB OVRB EN 0 CWG1B 0 STRB LSAC<1:0> `1' 00 `0' 01 High-Z 10 11 CWG Data C Auto-shutdown source (CWGxAS1 register) S Q R 1 1 POLC OVRC 0 CWG1C 0 STRC REN LSBD<1:0> SHUTDOWN = 0 `1' 00 `0' 01 High-Z 10 11 CWG Data D 1 POLD OVRD 0 1 0 CWG1D SHUTDOWN STRD FREEZE D Q CWG Data For example, when STRA = 0 then the corresponding pin is held at the level defined by OVRA. When STRA = 1, then the pin is driven by the modulated input signal. The POLy bits control the signal polarity only when STRy = 1. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 440 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... The CWG auto-shutdown operation also applies in Steering modes as described in Auto-Shutdown". An auto-shutdown event will only affect pins that have STRy = 1. 31.2.4.1 Synchronous Steering Mode In Synchronous Steering mode (MODE = 001), changes to steering selection registers take effect on the next rising edge of the modulated data input (see figure below). In Synchronous Steering mode, the output will always produce a complete waveform. Important: Only the STRx bits are synchronized; the OVRx bits are not synchronized. Figure 31-10. Example of Synchronous Steering (MODE = 001) Rev. 30-000101A 4/14/2017 CWG1 clock Input source CWG1A CWG1B 31.2.4.2 Asynchronous Steering Mode In Asynchronous mode (MODE = 000), steering takes effect at the end of the instruction cycle that writes to STRx. In Asynchronous Steering mode, the output signal may be an incomplete waveform (see figure below). This operation may be useful when the user firmware needs to immediately remove a signal from the output pin. Figure 31-11. Example of Asynchronous Steering (MODE = 000) Rev. 30-000102A 4/14/2017 CWG1 INPUT End of Instruction Cycle End of Instruction Cycle STRA CWG1A CWG1A Follows CWG1 data input 31.3 Start-up Considerations The application hardware must use the proper external pull-up and/or pull-down resistors on the CWG output pins. This is required because all I/O pins are forced to high-impedance at Reset. The polarity control bits (POLy) allow the user to choose whether the output signals are active-high or active-low. 31.4 Clock Source The clock source is used to drive the dead-band timing circuits. The CWG module allows the following clock sources to be selected: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 441 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... * * FOSC (system clock) HFINTOSC When the HFINTOSC is selected, the HFINTOSC will be kept running during Sleep. Therefore, CWG modes requiring dead band can operate in Sleep, provided that the CWG data input is also active during Sleep. The clock sources are selected using the CS bit. The system clock FOSC, is disabled in Sleep and thus dead-band control cannot be used. 31.5 Selectable Input Sources The CWG generates the output waveforms from the input sources which are selected with the ISM bits as shown below. Table 31-1. CWG Data Input Sources ISM Data Source 1111 Reserved 1110 CLC4_out 1101 CLC3_out 1100 CLC2_out 1011 CLC1_out 1010 DSM1_out 1001 C2_out 1000 C1_out 0111 NCO1_out 0110 PWM7_out 0101 PWM6_out 0100 CCP4_out 0011 CCP3_out 0010 CCP2_out 0001 CCP1_out 0000 Pin selected by CWGxINPPS 31.6 Output Control 31.6.1 CWG Outputs Each CWG output can be routed to a Peripheral Pin Select (PPS) output via the RxyPPS register. Related Links (PPS) Peripheral Pin Select Module (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 442 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.6.2 Polarity Control The polarity of each CWG output can be selected independently. When the output polarity bit is set, the corresponding output is active-high. Clearing the output polarity bit configures the corresponding output as active-low. However, polarity does not affect the override levels. Output polarity is selected with the POLy bits. Auto-shutdown and steering options are unaffected by polarity. 31.7 Dead-Band Control The dead-band control provides non-overlapping PWM signals to prevent shoot-through current in PWM switches. Dead-band operation is employed for Half-Bridge and Full-Bridge modes. The CWG contains two 6-bit dead-band counters. One is used for the rising edge of the input source control in Half-Bridge mode or for reverse dead-band Full-Bridge mode. The other is used for the falling edge of the input source control in Half-Bridge mode or for forward dead band in Full-Bridge mode. Dead band is timed by counting CWG clock periods from zero up to the value in the rising or falling deadband counter registers. 31.7.1 Dead-Band Functionality in Half-Bridge mode In Half-Bridge mode, the dead-band counters dictate the delay between the falling edge of the normal output and the rising edge of the inverted output. This can be seen in Figure 31-1. 31.7.2 Dead-Band Functionality in Full-Bridge mode In Full-Bridge mode, the dead-band counters are used when undergoing a direction change. The MODE<0> bit can be set or cleared while the CWG is running, allowing for changes from Forward to Reverse mode. The CWGxA and CWGxC signals will change immediately upon the first rising input edge following a direction change, but the modulated signals (CWGxB or CWGxD, depending on the direction of the change) will experience a delay dictated by the dead-band counters. 31.8 Rising Edge and Reverse Dead Band In Half-Bridge mode, the rising edge dead band delays the turn-on of the CWGxA output after the rising edge of the CWG data input. In Full-Bridge mode, the reverse dead-band delay is only inserted when changing directions from Forward mode to Reverse mode, and only the modulated output CWGxB is affected. The CWGxDBR register determines the duration of the dead-band interval on the rising edge of the input source signal. This duration is from 0 to 64 periods of the CWG clock. Dead band is always initiated on the edge of the input source signal. A count of zero indicates that no dead band is present. If the input source signal reverses polarity before the dead-band count is completed, then no signal will be seen on the respective output. The CWGxDBR register value is double-buffered. When EN = 0, the buffer is loaded when CWG1DBR is written. When EN = 1, then the buffer will be loaded at the rising edge following the first falling edge of the data input, after the LD bit is set. Refer to the following figure for an example. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 443 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Figure 31-12. Dead-Band Operation, CWGxDBR = 0x01, CWGxDBF = 0x02 Rev. 30-000103A 4/14/2017 cwg_clock Input Source CWGxA CWGxB 31.9 Falling Edge and Forward Dead Band In Half-Bridge mode, the falling edge dead band delays the turn-on of the CWGxB output at the falling edge of the CWG data input. In Full-Bridge mode, the forward dead-band delay is only inserted when changing directions from Reverse mode to Forward mode, and only the modulated output CWGxD is affected. The CWGxDBF register determines the duration of the dead-band interval on the falling edge of the input source signal. This duration is from zero to 64 periods of CWG clock. Dead-band delay is always initiated on the edge of the input source signal. A count of zero indicates that no dead band is present. If the input source signal reverses polarity before the dead-band count is completed, then no signal will be seen on the respective output. The CWGxDBF register value is double-buffered. When EN = 0, the buffer is loaded when CWGxDBF is written. When EN = 1, then the buffer will be loaded at the rising edge following the first falling edge of the data input after the LD is set. Refer to the following figure for an example. Figure 31-13. Dead-Band Operation, CWGxDBR = 0x03, CWGxDBF = 0x06, Source Shorter Than Dead Band Rev. 30-000104A 4/14/2017 cwg_clock Input Source CWGxA CWGxB source shorter than dead band 31.10 Dead-Band Jitter When the rising and falling edges of the input source are asynchronous to the CWG clock, it creates jitter in the dead-band time delay. The maximum jitter is equal to one CWG clock period. Refer to the equations below for more details. Equation 31-1. Dead-Band Delay Time Calculation 1 - _ = * < 5: 0 > _ (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 444 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... - _ = 1 * < 5: 0 > + 1 _ = - _ - - _ = 1 _ - _ = - _ + Equation 31-2. Dead-Band Delay Example Calculation < 5: 0 > = 00 = 10 _ = 8 = 1 = 125 8 - _ = 125 * 10 = 125 - _ = 1.25 + 0.125 = 1.37 31.11 Filename: Title: Last Edit: First Used: Notes: 10-000172C.vsd CWG SHUTDOWN BLOCK DIAGRAM 8/7/2015 PIC16(L)F1614/5/8/9 LECW Auto-Shutdown Auto-shutdown is a method to immediately override the CWG output levels with specific overrides that allow for safe shutdown of the circuit. The shutdown state can be either cleared automatically or held until cleared by software. The auto-shutdown circuit is illustrated in the following figure. Figure 31-16. CWG Shutdown Block Diagram Write `1' to SHUTDOWN bit Rev. 10-000172C 8/7/2015 PPS AS0E CWGxINPPS C1OUT_sync AS4E C2OUT_sync AS5E TMR2_postscaled AS1E TMR4_postscaled AS2E TMR6_postscaled AS3E S REN Write `0' to SHUTDOWN bit R Q SHUTDOWN S D FREEZE CWG_data Q CWG_shutdown CK 31.11.1 Shutdown The shutdown state can be entered by either of the following two methods: * * Software generated External Input 31.11.1.1 Software Generated Shutdown Setting the SHUTDOWN bit will force the CWG into the shutdown state. When the auto-restart is disabled, the shutdown state will persist as long as the SHUTDOWN bit is set. When auto-restart is enabled, the SHUTDOWN bit will clear automatically and resume operation on the next rising edge event. The SHUTDOWN bit indicates when a shutdown condition exists. The bit may be set or cleared in software or by hardware. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 445 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.11.1.2 External Input Source External shutdown inputs provide the fastest way to safely suspend CWG operation in the event of a Fault condition. When any of the selected shutdown inputs goes active, the CWG outputs will immediately go to the selected override levels without software delay. The override levels are selected by the LSBD and LSAC bits. Several input sources can be selected to cause a shutdown condition. All input sources are active-low. The shutdown input sources are individually enabled by the ASyE bits as shown in the following table: Table 31-2. Shutdown Sources ASyE Source AS6E CLC2_out/CLC3_out (low causes shutdown) AS5E CMP2_out (low causes shutdown) AS4E CMP1_out (low causes shutdown) AS3E TMR6_postscaled (high causes shutdown) AS2E TMR4_postscaled (high causes shutdown) AS1E TMR2_postscaled (high causes shutdown) AS0E Pin selected by CWGxPPS (low causes shutdown) Important: Shutdown inputs are level sensitive, not edge sensitive. The shutdown state cannot be cleared, except by disabling auto-shutdown, as long as the shutdown input level persists. 31.11.1.3 Pin Override Levels The levels driven to the CWG outputs during an auto-shutdown event are controlled by the LSBD and LSAC bits. The LSBD bits control CWG1B/D output levels, while the LSAC bits control the CWG1A/C output levels. 31.11.1.4 Auto-Shutdown Interrupts When an auto-shutdown event occurs, either by software or hardware setting SHUTDOWN, the CWG1IF flag bit of the PIRx register is set. Related Links PIR7 31.11.2 Auto-Shutdown Restart After an auto-shutdown event has occurred, there are two ways to resume operation: * * Software controlled Auto-restart In either case, the shutdown source must be cleared before the restart can take place. That is, either the shutdown condition must be removed, or the corresponding ASyE bit must be cleared. 31.11.2.1 Software-Controlled Restart When the REN bit is clear (REN = 0), the CWG module must be restarted after an auto-shutdown event through software. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 446 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Once all auto-shutdown sources are removed, the software must clear SHUTDOWN. Once SHUTDOWN is cleared, the CWG module will resume operation upon the first rising edge of the CWG data input. Important: The SHUTDOWN bit cannot be cleared in software if the auto-shutdown condition is still present. Figure 31-17. SHUTDOWN FUNCTIONALITY, AUTO-RESTART DISABLED (REN = 0, LSAC = 01, LSBD = 01) Rev. 30-000105A 4/14/2017 Shutdown Event Ceases REN Cleared by Software CWG Input Source Shutdown Source SHUTDOWN CWG1A CWG1C Tri-State (No Pulse) CWG1B CWG1D Tri-State (No Pulse) No Shutdown Shutdown Output Resumes 31.11.2.2 Auto-Restart When the REN bit is set (REN = 1), the CWG module will restart from the shutdown state automatically. Once all auto-shutdown conditions are removed, the hardware will automatically clear SHUTDOWN. Once SHUTDOWN is cleared, the CWG module will resume operation upon the first rising edge of the CWG data input. Important: The SHUTDOWN bit cannot be cleared in software if the auto-shutdown condition is still present. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 447 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... Figure 31-18. SHUTDOWN FUNCTIONALITY, AUTO-RESTART ENABLED (REN = 1, LSAC = 01, LSBD = 01) Rev. 30-000106A 4/14/2017 Shutdown Event Ceases REN auto-cleared by hardware CWG Input Source Shutdown Source SHUTDOWN CWG1A CWG1C CWG1B CWG1D Tri-State (No Pulse) Tri-State (No Pulse) No Shutdown Shutdown 31.12 Output Resumes Operation During Sleep The CWG module operates independently from the system clock and will continue to run during Sleep, provided that the clock and input sources selected remain active. The HFINTOSC remains active during Sleep when all the following conditions are met: * * * CWG module is enabled Input source is active HFINTOSC is selected as the clock source, regardless of the system clock source selected. In other words, if the HFINTOSC is simultaneously selected as the system clock and the CWG clock source, when the CWG is enabled and the input source is active, then the CPU will go idle during Sleep, but the HFINTOSC will remain active and the CWG will continue to operate. This will have a direct effect on the Sleep mode current. 31.13 Configuring the CWG 1. 2. 3. Ensure that the TRIS control bits corresponding to CWG outputs are set so that all are configured as inputs, ensuring that the outputs are inactive during setup. External hardware should ensure that pin levels are held to safe levels. Clear the EN bit, if not already cleared. Configure the MODE bits to set the output operating mode. 4. 5. 6. Configure the POLy bits to set the output polarities. Configure the ISM bits to select the data input source. If a steering mode is selected, configure the STRy bits to select the desired output on the CWG outputs. 7. Configure the LSBD and LSAC bits to select the auto-shutdown output override states (this is necessary even if not using auto-shutdown because start-up will be from a shutdown state). 8. If auto-restart is desired, set the REN bit. 9. If auto-shutdown is desired, configure the ASyE bits to select the shutdown source. 10. Set the desired rising and falling dead-band times with the CWGxDBR and CWGxDBF registers. 11. Select the clock source with the CS bits. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 448 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 12. Set the EN bit to enable the module. 13. Clear the TRIS bits that correspond to the CWG outputs to set them as outputs. If auto-restart is to be used, set the REN bit and the SHUTDOWN bit will be cleared automatically. Otherwise, clear the SHUTDOWN bit in software to start the CWG. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 449 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.14 Register Summary - CWG Control Offset Name Bit Pos. 0x060C CWG1CLK 7:0 0x060D CWG1ISM 7:0 0x060E CWG1DBR 7:0 0x060F CWG1DBF 7:0 0x0610 CWG1CON0 7:0 0x0611 CWG1CON1 7:0 0x0612 CWG1AS0 7:0 0x0613 CWG1AS1 7:0 0x0614 CWG1STR 7:0 CS ISM[3:0] DBR[5:0] DBF[5:0] EN LD MODE[2:0] IN SHUTDOWN OVRD REN OVRC POLD LSBD[1:0] POLC POLA LSAC[1:0] AS5E AS4E AS3E AS2E AS1E AS0E OVRB OVRA STRD STRC STRB STRA 0x0615 Reserved 0x0616 CWG2CLK 7:0 0x0617 CWG2ISM 7:0 0x0618 CWG2DBR 7:0 DBR[5:0] 0x0619 CWG2DBF 7:0 DBF[5:0] 0x061A CWG2CON0 7:0 0x061B CWG2CON1 7:0 0x061C CWG2AS0 7:0 0x061D CWG2AS1 7:0 0x061E CWG2STR 7:0 31.15 POLB CS ISM[3:0] EN LD MODE[2:0] IN SHUTDOWN REN OVRD OVRC POLD LSBD[1:0] POLC POLB POLA LSAC[1:0] AS5E AS4E AS3E AS2E AS1E AS0E OVRB OVRA STRD STRC STRB STRA Register Definitions: CWG Control Long bit name prefixes for the CWG peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 31-3. CWG Bit Name Prefixes Peripheral Bit Name Prefix CWG1 CWG1 CWG2 CWG2 Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 450 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.1 CWGxCON0 Name: Offset: CWGxCON0 0x610,0x61A CWG Control Register 0 Bit Access Reset 7 6 EN LD 5 4 3 2 1 0 R/W R/W/HC R/W R/W R/W 0 0 0 0 0 MODE[2:0] Bit 7 - EN CWG1 Enable bit Value 1 0 Description Module is enabled Module is disabled Bit 6 - LD CWG1 Load Buffers bit(1) Value 1 0 Description Dead-band count buffers to be loaded on CWG data rising edge, following first falling edge after this bit is set Buffers remain unchanged Bits 2:0 - MODE[2:0] CWG1 Mode bits Value 111 110 101 100 011 010 001 000 Description Reserved Reserved CWG outputs operate in Push-Pull mode CWG outputs operate in Half-Bridge mode CWG outputs operate in Reverse Full-Bridge mode CWG outputs operate in Forward Full-Bridge mode CWG outputs operate in Synchronous Steering mode CWG outputs operate in Asynchronous Steering mode Note: 1. This bit can only be set after EN = 1; it cannot be set in the same cycle when EN is set. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 451 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.2 CWGxCON1 Name: Offset: CWGxCON1 0x611,0x61B CWG Control Register 1 Bit 7 6 Access Reset 3 2 1 0 IN 5 4 POLD POLC POLB POLA RO R/W R/W R/W R/W x 0 0 0 0 Bit 5 - IN CWG Input Value bit (read-only) Value 1 0 Description CWG input is a logic 1 CWG input is a logic 0 Bits 0, 1, 2, 3 - POLy CWG Output 'y' Polarity bit Value 1 0 Description Signal output is inverted polarity Signal output is normal polarity (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 452 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.3 CWGxCLK Name: Offset: CWGxCLK 0x60C,0x616 CWGx Clock Input Selection Register Bit 7 6 5 4 3 2 1 0 CS Access R/W Reset 0 Bit 0 - CS Clock Source CWG Clock Source Selection Select bits Value 1 0 Description HFINTOSC (remains operating during Sleep) FOSC (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 453 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.4 CWGxISM Name: Offset: CWGxISM 0x60D,0x617 CWGx Input Selection Register Bit 7 6 5 4 3 2 1 0 ISM[3:0] Access Reset R/W R/W R/W R/W 0 0 0 0 Bits 3:0 - ISM[3:0] CWG Data Input Source Select bits Table 31-4. CWG Data Input Sources ISM Data Source 1111 Reserved 1110 CLC4_out 1101 CLC3_out 1100 CLC2_out 1011 CLC1_out 1010 DSM1_out 1001 C2_out 1000 C1_out 0111 NCO1_out 0110 PWM7_out 0101 PWM6_out 0100 CCP4_out 0011 CCP3_out 0010 CCP2_out 0001 CCP1_out 0000 Pin selected by CWGxINPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 454 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.5 CWGxSTR Name: Offset: CWGxSTR 0x614,0x61E CWG Steering Control Register (1) Bit Access Reset 7 6 5 4 3 2 1 0 OVRD OVRC OVRB OVRA STRD STRC STRB STRA R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 4, 5, 6, 7 - OVRy Steering Data OVR'y' bit Value x 1 0 Condition STRy = 1 Description CWGx'y' output has the CWG data input waveform with polarity control from POLy bit STRy = 0 and POLy = x CWGx'y' output is high STRy = 0 and POLy = x CWGx'y' output is low Bits 0, 1, 2, 3 - STRy STR'y' Steering Enable bit(2) Value 1 0 Description CWGx'y' output has the CWG data input waveform with polarity control from POLy bit CWGx'y' output is assigned to value of OVRy bit Note: 1. The bits in this register apply only when MODE = '00x' (CWGxCON0, Steering modes). 2. This bit is double-buffered when MODE = '001'. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 455 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.6 CWGxAS0 Name: Offset: CWGxAS0 0x612,0x61C CWG Auto-Shutdown Control Register 0 Bit Access Reset 7 6 SHUTDOWN REN 5 4 3 R/W/HS/HC R/W R/W R/W R/W R/W 0 0 0 1 0 1 LSBD[1:0] 2 1 0 LSAC[1:0] Bit 7 - SHUTDOWN Auto-Shutdown Event Status bit(1,2) Value 1 0 Description An auto-shutdown state is in effect No auto-shutdown event has occurred Bit 6 - REN Auto-Restart Enable bit Value 1 0 Description Auto-restart is enabled Auto-restart is disabled Bits 5:4 - LSBD[1:0] CWGxB and CWGxD Auto-Shutdown State Control bits Value 11 10 01 00 Description A logic `1' is placed on CWGxB/D when an auto-shutdown event occurs. A logic `0' is placed on CWGxB/D when an auto-shutdown event occurs. Pin is tri-stated on CWGxB/D when an auto-shutdown event occurs. The inactive state of the pin, including polarity, is placed on CWGxB/D after the required dead-band interval when an auto-shutdown event occurs. Bits 3:2 - LSAC[1:0] CWGxA and CWGxC Auto-Shutdown State Control bits Value 11 10 01 00 Description A logic `1' is placed on CWGxA/C when an auto-shutdown event occurs. A logic `0' is placed on CWGxA/C when an auto-shutdown event occurs. Pin is tri-stated on CWGxA/C when an auto-shutdown event occurs. The inactive state of the pin, including polarity, is placed on CWGxA/C after the required dead-band interval when an auto-shutdown event occurs. Note: 1. This bit may be written while EN = 0 (CWGxCON0), to place the outputs into the shutdown configuration. 2. The outputs will remain in auto-shutdown state until the next rising edge of the CWG data input after this bit is cleared. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 456 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.7 CWGxAS1 Name: Offset: CWGxAS1 0x613,0x61D CWG Auto-Shutdown Control Register 1 Bit 7 6 Access Reset 5 4 3 2 1 0 AS5E AS4E AS3E AS2E AS1E AS0E R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 Bits 0, 1, 2, 3, 4, 5 - ASyE CWG Auto-shutdown Source ASyE Enable bit(1) Table 31-5. Shutdown Sources ASyE Source AS6E CLC2_out/CLC3_out (low causes shutdown) AS5E CMP2_out (low causes shutdown) AS4E CMP1_out (low causes shutdown) AS3E TMR6_postscaled (high causes shutdown) AS2E TMR4_postscaled (high causes shutdown) AS1E TMR2_postscaled (high causes shutdown) AS0E Pin selected by CWGxPPS (low causes shutdown) Value 1 0 Description Auto-shutdown for source ASyE is enabled Auto-shutdown for source ASyE is disabled Note: This bit may be written while EN = 0 (CWGxCON0), to place the outputs into the shutdown configuration. The outputs will remain in auto-shutdown state until the next rising edge of the CWG data input after this bit is cleared. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 457 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.8 CWGxDBR Name: Offset: CWGxDBR 0x60E,0x618 CWG Rising Dead-Band Count Register Bit 7 6 5 4 3 2 1 0 DBR[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - DBR[5:0] CWG Rising Edge Triggered Dead-Band Count bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value n 0 Description Dead band is active no less than n, and no more than n+1, CWG clock periods after the rising edge 0 CWG clock periods. Dead-band generation is bypassed (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 458 PIC16(L)F18424/44 (CWG) Complementary Waveform Generator Modul... 31.15.9 CWGxDBF Name: Offset: CWGxDBF 0x60F,0x619 CWG Falling Dead-Band Count Register Bit 7 6 5 4 3 2 1 0 DBF[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - DBF[5:0] CWG Falling Edge Triggered Dead-Band Count bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value n 0 Description Dead band is active no less than n, and no more than n+1, CWG clock periods after the falling edge 0 CWG clock periods. Dead-band generation is bypassed (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 459 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32. (DSM) Data Signal Modulator Module The Data Signal Modulator (DSM) is a peripheral which allows the user to mix a data stream, also known as a modulator signal, with a carrier signal to produce a modulated output. Both the carrier and the modulator signals are supplied to the DSM module either internally, from the output of a peripheral, or externally through an input pin. The modulated output signal is generated by performing a logical "AND" operation of both the carrier and modulator signals and then provided to the MDOUT pin. The carrier signal is comprised of two distinct and separate signals. A carrier high (CARH) signal and a carrier low (CARL) signal. During the time in which the modulator (MOD) signal is in a logic high state, the DSM mixes the carrier high signal with the modulator signal. When the modulator signal is in a logic low state, the DSM mixes the carrier low signal with the modulator signal. Using this method, the DSM can generate the following types of Key Modulation schemes: * * * Frequency-Shift Keying (FSK) Phase-Shift Keying (PSK) On-Off Keying (OOK) Additionally, the following features are provided within the DSM module: * * * * * Carrier Synchronization Carrier Source Polarity Select Programmable Modulator Data Modulated Output Polarity Select Peripheral Module Disable, which provides the ability to place the DSM module in the lowest power consumption mode The figure below shows a Simplified Block Diagram of the Data Signal Modulator peripheral. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 460 Filename: Title: Last Edit: First Used: Notes: 10-000248F.vsd DSM BLOCK DIAGRAM for PIC18(L)F6xK40 1/19/2016 PIC18(L)F6xK40 (MVAC/MVAK) PIC16(L)F18424/44 (DSM) Data Signal Modulator Module Figure 32-1. Simplified Block Diagram of the Data Signal Modulator MDCHS<3:0> Rev. 10-000248F 1/19/2016 Data Signal Modulator 0000 See MDCARH Register CARH MDCHPOL D SYNC 1111 Q 1 MDSRCS<4:0> 0 00000 MDCHSYNC RxyPPS See MDSRC Register MOD PPS MDOPOL 11111 MDCLS<3:0> D SYNC 0000 Q 1 0 See MDCARL Register CARL MDCLSYNC MDCLPOL 1111 32.1 DSM Operation The DSM module can be enabled by setting the EN bit in the MDCON0 register. Clearing the EN bit, disables the output of the module but retain the carrier and source signal selections. The module will resume operation when the EN bit is set again. The output of the DSM module can be rerouted to several pins using the RxyPPS register. When the EN bit is cleared the output pin is held low. 32.2 Modulator Signal Sources The modulator signal can be supplied from the following sources selected with the SRCS bits: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 461 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module Table 32-1. MDSRC Selection MUX Connections 32.3 SRCS<4:0> Connection 11111-10001 Reserved 10000 MSSP1 - SDO 01111 EUSART1 TX (TX/CK output) 01110 CLC4 OUT 01101 CLC3 OUT 01100 CLC2 OUT 01011 CLC1 OUT 01010 C2 OUT 01001 C1 OUT 01000 NCO1 OUT 00111 PWM7 OUT 00110 PWM6 OUT 00101 CCP4 OUT 00100 CCP3 OUT 00011 CCP2 OUT 00010 CCP1 OUT 00001 MDBIT 00000 Pin selected by MDSRCPPS Carrier Signal Sources The carrier high signal and carrier low signal can be supplied from the following sources. The carrier high signal is selected by configuring the CHS bits. Table 32-2. MDCARH Source Selections MDCARH CHS<3:0> Connection 1111 Reserved 1110 CLC4 OUT 1101 CLC3 OUT 1100 CLC2 OUT 1011 CLC1 OUT 1010 NCO1 OUT (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 462 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module MDCARH CHS<3:0> Connection 1001 PWM7 OUT 1000 PWM6 OUT 0111 CCP4 OUT 0110 CCP3 OUT 0101 CCP2 OUT 0100 CCP1 OUT 0011 CLKREF output 0010 HFINTOSC 0001 FOSC (system clock) 0000 Pin selected by MDCARHPPS The carrier low signal is selected by configuring the CLS bits. Table 32-3. MDCARL Source Selections MDCARL CLS<3:0> Connection 1111 Reserved 1110 CLC4 OUT 1101 CLC3 OUT 1100 CLC2 OUT 1011 CLC1 OUT 1010 NCO1 OUT 1001 PWM7 OUT 1000 PWM6 OUT 0111 CCP4 OUT 0110 CCP3 OUT 0101 CCP2 OUT 0100 CCP1 OUT 0011 CLKREF output 0010 HFINTOSC 0001 FOSC (system clock) 0000 Pin selected by MDCARLPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 463 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.4 Carrier Synchronization During the time when the DSM switches between carrier high and carrier low signal sources, the carrier data in the modulated output signal can become truncated. To prevent this, the carrier signal can be synchronized to the modulator signal. When synchronization is enabled, the carrier pulse that is being mixed at the time of the transition is allowed to transition low before the DSM switches over to the next carrier source. Synchronization is enabled separately for the carrier high and carrier low signal sources. Synchronization for the carrier high signal is enabled by setting the CHSYNC bit. Synchronization for the carrier low signal is enabled by setting the CLSYNC bit. The figures below show the timing diagrams of using various synchronization methods. Figure 32-2. On Off Keying (OOK) Synchronization Rev. 30-000144A 5/26/2017 carrier_low carrier_high modulator MDCHSYNC = 1 MDCLSYNC = 0 MDCHSYNC = 1 MDCLSYNC = 1 MDCHSYNC = 0 MDCLSYNC = 0 MDCHSYNC = 0 MDCLSYNC = 1 Figure 32-3. No Synchronization (MDCHSYNC = 0, MDCLSYNC = 0) Rev. 30-000145A 5/26/2017 carrier_high carrier_low modulator MDCHSYNC = 0 MDCLSYNC = 0 Active Carrier State carrier_high (c) 2018 Microchip Technology Inc. carrier_low carrier_high Datasheet Preliminary carrier_low DS40002000A-page 464 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module Figure 32-4. Carrier High Synchronization (MDCHSYNC = 1, MDCLSYNC = 0) Rev. 30-000146A 5/26/2017 carrier_high carrier_low modulator MDCHSYNC = 1 MDCLSYNC = 0 Active Carrier State carrier_high both carrier_low carrier_high both carrier_low Figure 32-5. Carrier Low Synchronization (MDCHSYNC = 0, MDCLSYNC = 1) Rev. 30-000147A 5/26/2017 carrier_high carrier_low modulator MDCHSYNC = 0 MDCLSYNC = 1 Active Carrier State carrier_high carrier_low carrier_high carrier_low Figure 32-6. Full Synchronization (MDCHSYNC = 1, MDCLSYNC = 1) Rev. 30-000148A 5/26/2017 carrier_high carrier_low modulator Falling edges used to sync MDCHSYNC = 1 MDCLSYNC = 1 Active Carrier State 32.5 carrier_high carrier_low carrier_high CL Carrier Source Polarity Select The signal provided from any selected input source for the carrier high and carrier low signals can be inverted. Inverting the signal for the carrier high and low source is enabled by setting the CHPOL bit and the CLPOL bit, respectively. 32.6 Programmable Modulator Data The BIT bit can be selected as the modulation source. This gives the user the ability to provide software driven modulation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 465 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.7 Modulated Output Polarity The modulated output signal provided on the DSM pin can also be inverted. Inverting the modulated output signal is enabled by setting the OPOL bit. 32.8 Operation in Sleep Mode The DSM can still operate during Sleep, if the Carrier and Modulator input sources are also still operable during Sleep. Refer to "Power-Saving Operation Modes" for more details. 32.9 Effects of a Reset Upon any device Reset, the DSM module is disabled. The user's firmware is responsible for initializing the module before enabling the output. All the registers are reset to their default values. 32.10 Peripheral Module Disable The DSM module can be completely disabled using the PMD module to achieve maximum power saving. When the DSMMD bit of PMDx register is set, the DSM module is completely disabled. This puts the module in its lowest power consumption state. When enabled again all the registers of the DSM module default to POR status. Related Links Register Definitions: Peripheral Module Disable (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 466 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.11 Register Summary - DSM Offset Name Bit Pos. 0x0897 MD1CON0 7:0 0x0898 MD1CON1 7:0 0x0899 MD1SRC 7:0 0x089A MD1CARL 7:0 CLS[3:0] 0x089B MD1CARH 7:0 CHS[3:0] 32.12 EN OUT OPOL CHPOL CHSYNC BIT CLPOL CLSYNC SRCS[4:0] Register Definitions: Modulation Control Long bit name prefixes for the Modulation Control peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 32-4. Modulation Control Long Bit Name Prefixes Peripheral Bit Name Prefix MD MD Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 467 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.12.1 MDxCON0 Name: Offset: MDxCON0 0x0897 Modulation Control Register 0 Bit Access Reset 5 4 EN 7 6 OUT OPOL 3 2 1 BIT 0 R/W R/W R/W R/W 0 0 0 0 Bit 7 - EN Modulator Module Enable bit Value 1 0 Description Modulator module is enabled and mixing input signals Modulator module is disabled and has no output Bit 5 - OUT Modulator Output bit Displays the current output value of the modulator module. Bit 4 - OPOL Modulator Output Polarity Select bit Value 1 0 Description Modulator output signal is inverted; idle high output Modulator output signal is not inverted; idle low output Bit 0 - BIT Modulation Source Select Input bit Allows software to manually set modulation source input to module Note: 1. The modulated output frequency can be greater and asynchronous from the clock that updates this register bit, the bit value may not be valid for higher speed modulator or carrier signals. 2. MDBIT must be selected as the modulation source in the MDxSRC register for this operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 468 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.12.2 MDxCON1 Name: Offset: MDxCON1 0x0898 Modulation Control Register 1 Bit 7 6 Access Reset 5 4 1 0 CHPOL CHSYNC 3 2 CLPOL CLSYNC R/W R/W R/W R/W 0 0 0 0 Bit 5 - CHPOL Modulator High Carrier Polarity Select bit Value 1 0 Description Selected high carrier signal is inverted Selected high carrier signal is not inverted Bit 4 - CHSYNC Modulator High Carrier Synchronization Enable bit Value 1 0 Description Modulator waits for a falling edge on the high time carrier signal before allowing a switch to the low time carrier Modulator output is not synchronized to the high time carrier signal Bit 1 - CLPOL Modulator Low Carrier Polarity Select bit Value 1 0 Description Selected low carrier signal is inverted Selected low carrier signal is not inverted Bit 0 - CLSYNC Modulator Low Carrier Synchronization Enable bit Value 1 0 Description Modulator waits for a falling edge on the low time carrier signal before allowing a switch to the high time carrier Modulator output is not synchronized to the low time carrier signal Note: 1. Narrowed carrier pulse widths or spurs may occur in the signal stream if the carrier is not synchronized. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 469 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.12.3 MDxCARH Name: Offset: MDxCARH 0x089B Modulation High Carrier Control Register Bit 7 6 5 4 3 2 1 0 CHS[3:0] Access R/W R/W R/W R/W 0 0 0 0 Reset Bits 3:0 - CHS[3:0] Modulator Carrier High Selection bits Table 32-5. MDCARH Source Selections MDCARH CHS<3:0> Connection 1111 Reserved 1110 CLC4 OUT 1101 CLC3 OUT 1100 CLC2 OUT 1011 CLC1 OUT 1010 NCO1 OUT 1001 PWM7 OUT 1000 PWM6 OUT 0111 CCP4 OUT 0110 CCP3 OUT 0101 CCP2 OUT 0100 CCP1 OUT 0011 CLKREF output 0010 HFINTOSC 0001 FOSC (system clock) 0000 Pin selected by MDCARHPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 470 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.12.4 MDxCARL Name: Offset: MDxCARL 0x089A Modulation Low Carrier Control Register Bit 7 6 5 4 3 2 1 0 CLS[3:0] Access R/W R/W R/W R/W 0 0 0 0 Reset Bits 3:0 - CLS[3:0] Modulator Carrier Low Input Selection bits Table 32-6. MDCARL Source Selections MDCARL CLS<3:0> Connection 1111 Reserved 1110 CLC4 OUT 1101 CLC3 OUT 1100 CLC2 OUT 1011 CLC1 OUT 1010 NCO1 OUT 1001 PWM7 OUT 1000 PWM6 OUT 0111 CCP4 OUT 0110 CCP3 OUT 0101 CCP2 OUT 0100 CCP1 OUT 0011 CLKREF output 0010 HFINTOSC 0001 FOSC (system clock) 0000 Pin selected by MDCARLPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 471 PIC16(L)F18424/44 (DSM) Data Signal Modulator Module 32.12.5 MDxSRC Name: Offset: MDxSRC 0x0899 Modulation Source Control Register Bit 7 6 5 4 3 2 1 0 SRCS[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - SRCS[4:0] Modulator Source Selection bits Table 32-7. MDSRC Selection MUX Connections SRCS<4:0> Connection 11111-10001 Reserved 10000 MSSP1 - SDO 01111 EUSART1 TX (TX/CK output) 01110 CLC4 OUT 01101 CLC3 OUT 01100 CLC2 OUT 01011 CLC1 OUT 01010 C2 OUT 01001 C1 OUT 01000 NCO1 OUT 00111 PWM7 OUT 00110 PWM6 OUT 00101 CCP4 OUT 00100 CCP3 OUT 00011 CCP2 OUT 00010 CCP1 OUT 00001 MDBIT 00000 Pin selected by MDSRCPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 472 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33. (CLC) Configurable Logic Cell The Configurable Logic Cell (CLCx) module provides programmable logic that operates outside the speed limitations of software execution. The logic cell takes up to 64 input signals and, through the use of configurable gates, reduces the 64 inputs to four logic lines that drive one of eight selectable singleoutput logic functions. Input sources are a combination of the following: * I/O pins * Internal clocks * Peripherals * Register bits The output can be directed internally to peripherals and to an output pin. Important: There are several CLC instances on this device. Throughout this section, the lower case `x' in register names is a generic reference to the CLC instance number. For example, the first instance of the control register is CLC1CON and is generically described in this chapter as CLCxCON. The following figure is a simplified diagram showing signal flow through the CLC. Possible configurations include: * Combinatorial Logic - AND - NAND - AND-OR - AND-OR-INVERT - OR-XOR - OR-XNOR * Latches - S-R - Clocked D with Set and Reset - Transparent D with Set and Reset (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 473 PIC16(L)F18424/44 (CLC) Configurable Logic Cell Figure 33-1. CLC Simplified Block Diagram Rev. 10-000025H 11/9/2016 D Q OUT CLCxOUT Q1 . . . LCx_in[n-2] LCx_in[n-1] LCx_in[n] CLCx_out Input Data Selection Gates(1) LCx_in[0] LCx_in[1] LCx_in[2] EN lcxg1 lcxg2 lcxg3 to Peripherals CLCxPPS Logic lcxq Function PPS (2) CLCx lcxg4 POL MODE<2:0> TRIS Interrupt det INTP INTN set bit CLCxIF Interrupt det Note: 1. See Figure 33-2 for input data selection and gating. 2. See Figure 33-3 for programmable logic functions. 33.1 CLC Setup Programming the CLC module is performed by configuring the four stages in the logic signal flow. The four stages are: * Data selection * Data gating * Logic function selection * Output polarity Each stage is setup at run time by writing to the corresponding CLC Special Function Registers. This has the added advantage of permitting logic reconfiguration on-the-fly during program execution. 33.1.1 Data Selection There are 64 signals available as inputs to the configurable logic. Four 64-input multiplexers are used to select the inputs to pass on to the next stage. Data selection is through four multiplexers as indicated on the left side of the following diagram. Data inputs in the figure are identified by a generic numbered input name. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 474 PIC16(L)F18424/44 (CLC) Configurable Logic Cell Figure 33-2. Input Data Selection and Gating Rev. 30-000149A 6/12/2017 LCx_in[0] Data Selection 000000 Data GATE 1 LCx_in[n] d1T G 1 D1 T d1N G 1 D1 N G 1 D2 T 111111 D1S<5:0> G 1 D2 N LCx_in[0] lcxg1 000000 d2T G 1 D3 T G 1 D3 N G 1 D4 T G 1 D4 N G1POL d2N LCx_in[n] 111111 D2S<5:0> LCx_in[0] 000000 Data GATE 2 lcxg2 d3T (Same as Data GATE 1) d3N LCx_in[n] Data GATE 3 111111 lcxg3 D3S<5:0> LCx_in[0] (Same as Data GATE 1) Data GATE 4 000000 lcxg4 (Same as Data GATE 1) d4T d4N LCx_in[n] 111111 D4S<5:0> Note: All controls are undefined at power-up. The following table correlates the generic input name to the actual signal for each CLC module. The column labeled `DyS Value' indicates the MUX selection code for the selected data input. DyS is an abbreviation for the MUX select input codes: D1S through D4S where 'y' is the gate number. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 475 PIC16(L)F18424/44 (CLC) Configurable Logic Cell CLC Data Input Sources DyS Value CLC Input Source DyS Value CLC Input Source 111111 [63] Reserved 011111 [31] DSM1_out 111110 [62] Reserved 011110 [30] IOC_flag 111101 [61] Reserved 011101 [29] ZCD_out 111100 [60] Reserved 011100 [28] C2_out 111011 [59] Reserved 011011 [27] C1_out 111010 58] Reserved 011010 [26] NCO1_out 111001 [57] Reserved 011001 [25] PWM7_out 111000 [56] Reserved 011000 [24] PWM6 _out 110111 [55] Reserved 010111 [23] CCP4_out 110110 [54] Reserved 010110 [22] CCP3_out 110101 [53] Reserved 010101 [21] CCP2_out 110100 [52] Reserved 010100 [20] CCP1_out 110011 [51] Reserved 010011 [19] SMT1_overflow 110010 [50] Reserved 010010 [18] TMR6 _out 110001 [49] Reserved 010001 [17] TMR5 _overflow 110000 [48] Reserved 010000 [16] TMR4_out 101111 [47] Reserved 001111 [15] TMR3 _overflow 101110 [46] Reserved 001110 [14] TMR2_out 101101 [45] CWG2B_out 001101 [13] TMR1_overflow 101100 [44] CWG2A_out 001100 [12] TMR0_overflow 101011 [43] CWG1B_out 001011 [11] CLKR_out 101010 [42] CWG1A_out 001010 [10] FRC 101001 [41] Reserved 001001 [9] SOSC 101000 [40] Reserved 001000 [8] MFINTOSC (32 kHz) 100111 [39] MSSP1_clk_out 000111 [7] MFINTOSC (500 kHz) 100110 [38] MSSP1_data_out 000110 [6] LFINTOSC 100101 [37] EUSART1_CK_out 000101 [5] HFINTOSC (32 MHz) 100100 [36] EUSART1_DT_out 000100 [4] FOSC 100011 [35] CLC4_out 000011 [3] CLCIN3PPS 100010 [34] CLC3_out 000010 [2] CLCIN2PPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 476 PIC16(L)F18424/44 (CLC) Configurable Logic Cell DyS Value CLC Input Source DyS Value CLC Input Source 100001 [33] CLC2_out 000001 [1] CLCIN1PPS 100000 [32] CLC1_out 000000 [0] CLCIN0PPS Data inputs are selected with CLCxSEL0 through CLCxSEL3 registers. Important: Data selections are undefined at power-up. 33.1.2 Data Gating Outputs from the input multiplexers are directed to the desired logic function input through the data gating stage. Each data gate can direct any combination of the four selected inputs. The gate stage is more than just signal direction. The gate can be configured to direct each input signal as inverted or non-inverted data. Directed signals are ANDed together in each gate. The output of each gate can be inverted before going on to the logic function stage. The gating is in essence a 1-to-4 input AND/NAND/OR/NOR gate. When every input is inverted and the output is inverted, the gate is an AND of all enabled data inputs. When the inputs and output are not inverted, the gate is an OR or all enabled inputs. The following table summarizes the basic logic that can be obtained in gate 1 by using the gate logic select bits. The table shows the logic of four input variables, but each gate can be configured to use less than four. If no inputs are selected, the output will be zero or one, depending on the gate output polarity bit. Table 33-1. Data Gating Logic CLCxGLSy GyPOL Gate Logic 0x55 1 AND 0x55 0 NAND 0xAA 1 NOR 0xAA 0 OR 0x00 0 Logic 0 0x00 1 Logic 1 It is possible (but not recommended) to select both the true and negated values of an input. When this is done, the gate output is zero, regardless of the other inputs, but may emit logic glitches (transientinduced pulses). If the output of the channel must be zero or one, the recommended method is to set all gate bits to zero and use the gate polarity bit to set the desired level. Data gating is configured with the logic gate select registers as follows: * Gate 1: CLCxSEL0 * Gate 2: CLCxSEL1 * Gate 3: CLCxSEL2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 477 PIC16(L)F18424/44 (CLC) Configurable Logic Cell * Gate 4: CLCxSEL3 Register number suffixes are different than the gate numbers because other variations of this module have multiple gate selections in the same register. Data gating is indicated in the right side of Figure 33-2. Only one gate is shown in detail. The remaining three gates are configured identically with the exception that the data enables correspond to the enables for that gate. 33.1.3 Logic Function There are eight available logic functions including: * * * * * * * * AND-OR OR-XOR AND S-R Latch D Flip-Flop with Set and Reset D Flip-Flop with Reset J-K Flip-Flop with Reset Transparent Latch with Set and Reset Logic functions are shown in the following diagram. Each logic function has four inputs and one output. The four inputs are the four data gate outputs of the previous stage. The output is fed to the inversion stage and from there to other peripherals, an output pin, and back to the CLC itself. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 478 PIC16(L)F18424/44 (CLC) Configurable Logic Cell Figure 33-3. Programmable Logic Functions Rev. 10-000122B 9/13/2016 AND-OR OR-XOR lcxg1 lcxg1 lcxg2 lcxg2 lcxq lcxq lcxg3 lcxg3 lcxg4 lcxg4 MODE<2:0> = 000 MODE<2:0> = 001 4-input AND S-R Latch lcxg1 lcxg1 S lcxg2 lcxg2 Q lcxq Q lcxq lcxq lcxg3 lcxg3 lcxg4 R lcxg4 MODE<2:0> = 010 MODE<2:0> = 011 1-Input D Flip-Flop with S and R 2-Input D Flip-Flop with R lcxg4 lcxg2 D lcxg1 S Q lcxq lcxg4 D lcxg2 lcxg1 R lcxg3 R lcxg3 MODE<2:0> = 100 MODE<2:0> = 101 J-K Flip-Flop with R 1-Input Transparent Latch with S and R lcxg2 J Q lcxq lcxg4 lcxg2 D lcxg3 LE S Q lcxq lcxg1 lcxg4 K R lcxg3 R lcxg1 MODE<2:0> = 110 MODE<2:0> = 111 33.1.4 Output Polarity The last stage in the Configurable Logic Cell is the output polarity. Setting the POL bit inverts the output signal from the logic stage. Changing the polarity while the interrupts are enabled will cause an interrupt for the resulting output transition. 33.2 CLC Interrupts An interrupt will be generated upon a change in the output value of the CLCx when the appropriate interrupt enables are set. A rising edge detector and a falling edge detector are present in each CLC for this purpose. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 479 PIC16(L)F18424/44 (CLC) Configurable Logic Cell The CLCxIF bit of the associated PIR register will be set when either edge detector is triggered and its associated enable bit is set. The INTP enables rising edge interrupts and the INTN bit enables falling edge interrupts. To fully enable the interrupt, set the following bits: * CLCxIE bit of the respective PIE register * INTP bit (for a rising edge detection) * INTN bit (for a falling edge detection) * If priority interrupts are not used - Clear the IPEN bit of the INTCON register - Set the GIE bit of the INTCON register - Set the PEIE bit of the INTCON register * If the CLC is a high priority interrupt - Set the IPEN bit of the INTCON register - Set the CLCxIP bit of the respective IPR register - Set the GIEH bit of the INTCON register * If the CLC is a low priority interrupt - Set the IPEN bit of the INTCON register - Clear the CLCxIP bit of the respective IPR register - Set the GIEL bit of the INTCON register The CLCxIF bit of the respective PIR register, must be cleared in software as part of the interrupt service. If another edge is detected while this flag is being cleared, the flag will still be set at the end of the sequence. Related Links INTCON PIE5 PIR5 33.3 Output Mirror Copies Mirror copies of all CLCxOUT bits are contained in the CLCDATA register. Reading this register reads the outputs of all CLCs simultaneously. This prevents any reading skew introduced by testing or reading the OUT bits in the individual CLCxCON registers. 33.4 Effects of a Reset The CLCxCON register is cleared to zero as the result of a Reset. All other selection and gating values remain unchanged. 33.5 Operation During Sleep The CLC module operates independently from the system clock and will continue to run during Sleep, provided that the input sources selected remain active. The HFINTOSC remains active during Sleep when the CLC module is enabled and the HFINTOSC is selected as an input source, regardless of the system clock source selected. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 480 PIC16(L)F18424/44 (CLC) Configurable Logic Cell In other words, if the HFINTOSC is simultaneously selected as the system clock and as a CLC input source, when the CLC is enabled, the CPU will go idle during Sleep, but the CLC will continue to operate and the HFINTOSC will remain active. This will have a direct effect on the Sleep mode current. 33.6 CLC Setup Steps The following steps should be followed when setting up the CLC: * * * * * * * * * * * Disable CLC by clearing the EN bit. Select desired inputs using the CLCxSEL0 through CLCxSEL3 registers (See CLC Data Input Table). Clear any associated ANSEL bits. Set all TRIS bits associated with inputs. Enable the chosen inputs through the four gates using the CLCxGLS0 through CLCxGLS3 registers. Select the gate output polarities with the GyPOL bits Select the desired logic function with the MODE bits Select the desired polarity of the logic output with the POL bit. (This step may be combined with the previous gate output polarity step). If driving a device pin, set the desired pin PPS control register and also clear the TRIS bit corresponding to that output. Configure the interrupts (optional). See CLC Interrupts Enable the CLC by setting the EN bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 481 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.7 Register Summary - CLC Control Offset Name Bit Pos. 0x1E0F CLCDATA 7:0 0x1E10 CLC1CON 7:0 EN 0x1E11 CLC1POL 7:0 POL 0x1E12 CLC1SEL0 7:0 D1S[5:0] 0x1E13 CLC1SEL1 7:0 D2S[5:0] 0x1E14 CLC1SEL2 7:0 D3S[5:0] 0x1E15 CLC1SEL3 7:0 0x1E16 CLC1GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T 0x1E17 CLC1GLS1 7:0 G2D4T G2D4N G2D3T G2D3N G2D2T 0x1E18 CLC1GLS2 7:0 G3D4T G3D4N G3D3T G3D3N 0x1E19 CLC1GLS3 7:0 G4D4T G4D4N G4D3T G4D3N 0x1E1A CLC2CON 7:0 EN OUT INTP 0x1E1B CLC2POL 7:0 POL 0x1E1C CLC2SEL0 7:0 D1S[5:0] 0x1E1D CLC2SEL1 7:0 D2S[5:0] 0x1E1E CLC2SEL2 7:0 D3S[5:0] 0x1E1F CLC2SEL3 7:0 D4S[5:0] 0x1E20 CLC2GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T 0x1E21 CLC2GLS1 7:0 G2D4T G2D4N G2D3T G2D3N G2D2T 0x1E22 CLC2GLS2 7:0 G3D4T G3D4N G3D3T G3D3N 0x1E23 CLC2GLS3 7:0 G4D4T G4D4N G4D3T G4D3N 0x1E24 CLC3CON 7:0 EN OUT INTP INTN 0x1E25 CLC3POL 7:0 POL 0x1E26 CLC3SEL0 7:0 D1S[5:0] 0x1E27 CLC3SEL1 7:0 D2S[5:0] 0x1E28 CLC3SEL2 7:0 D3S[5:0] 0x1E29 CLC3SEL3 7:0 D4S[5:0] 0x1E2A CLC3GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T 0x1E2B CLC3GLS1 7:0 G2D4T G2D4N G2D3T G2D3N G2D2T 0x1E2C CLC3GLS2 7:0 G3D4T G3D4N G3D3T G3D3N 0x1E2D CLC3GLS3 7:0 G4D4T G4D4N G4D3T 0x1E2E CLC4CON 7:0 EN OUT 0x1E2F CLC4POL 7:0 POL 0x1E30 CLC4SEL0 7:0 D1S[5:0] 0x1E31 CLC4SEL1 7:0 D2S[5:0] 0x1E32 CLC4SEL2 7:0 D3S[5:0] 0x1E33 CLC4SEL3 7:0 0x1E34 CLC4GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T 0x1E35 CLC4GLS1 7:0 G2D4T G2D4N G2D3T G2D3N 0x1E36 CLC4GLS2 7:0 G3D4T G3D4N G3D3T G3D3N 0x1E37 CLC4GLS3 7:0 G4D4T G4D4N G4D3T G4D3N MLC4OUT OUT INTP MLC3OUT INTN MLC2OUT MLC1OUT MODE[2:0] G4POL G3POL G2POL G1POL G1D2N G1D1T G1D1N G2D2N G2D1T G2D1N G3D2T G3D2N G3D1T G3D1N G4D2T G4D2N G4D1T G4D1N D4S[5:0] INTN MODE[2:0] G4POL G3POL G2POL G1POL G1D2N G1D1T G1D1N G2D2N G2D1T G2D1N G3D2T G3D2N G3D1T G3D1N G4D2T G4D2N G4D1T G4D1N MODE[2:0] G4POL G3POL G2POL G1POL G1D2N G1D1T G1D1N G2D2N G2D1T G2D1N G3D2T G3D2N G3D1T G3D1N G4D3N G4D2T G4D2N G4D1T G4D1N INTP INTN MODE[2:0] G4POL G3POL G2POL G1POL G1D2N G1D1T G1D1N G2D2T G2D2N G2D1T G2D1N G3D2T G3D2N G3D1T G3D1N G4D2T G4D2N G4D1T G4D1N D4S[5:0] (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 482 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8 Register Definitions: Configurable Logic Cell Long bit name prefixes for the CLC peripherals are shown in the table below. Refer to the "Long Bit Names Section" for more information. Table 33-2. CLC Bit Name Prefixes Peripheral Bit Name Prefix CLC1 LC1 CLC2 LC2 CLC3 LC3 CLC4 LC4 Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 483 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.1 CLCxCON Name: Offset: CLCxCON 0x1E10,0x1E1A,0x1E24,0x1E2E Configurable Logic Cell Control Register Bit Access Reset 5 4 3 EN 7 6 OUT INTP INTN 2 1 0 R/W RO R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 MODE[2:0] Bit 7 - EN CLC Enable bit Value 1 0 Description Configurable logic cell is enabled and mixing signals Configurable logic cell is disabled and has logic zero output Bit 5 - OUT Logic cell output data, after LCPOL. Sampled from CLCxOUT Bit 4 - INTP Configurable Logic Cell Positive Edge Going Interrupt Enable bit Value 1 0 Description CLCxIF will be set when a rising edge occurs on CLCxOUT Rising edges on CLCxOUT have no effect on CLCxIF Bit 3 - INTN Configurable Logic Cell Negative Edge Going Interrupt Enable bit Value 1 0 Description CLCxIF will be set when a falling edge occurs on CLCxOUT Falling edges on CLCxOUT have no effect on CLCxIF Bits 2:0 - MODE[2:0] Configurable Logic Cell Functional Mode Selection bits Value 111 110 101 100 011 010 001 000 Description Cell is 1-input transparent latch with Set and Reset Cell is J-K flip-flop with Reset Cell is 2-input D flip-flop with Reset Cell is 1-input D flip-flop with Set and Reset Cell is S-R latch Cell is 4-input AND Cell is OR-XOR Cell is AND-OR (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 484 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.2 CLCxPOL Name: Offset: CLCxPOL 0x1E11,0x1E1B,0x1E25,0x1E2F Signal Polarity Control Register Bit Access Reset 3 2 1 0 POL 7 6 5 4 G4POL G3POL G2POL G1POL R/W R/W R/W R/W R/W 0 x x x x Bit 7 - POL CLCxOUT Output Polarity Control bit Value 1 0 Description The output of the logic cell is inverted The output of the logic cell is not inverted Bits 0, 1, 2, 3 - GyPOL Gate Output Polarity Control bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description The gate output is inverted when applied to the logic cell The output of the gate is not inverted (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 485 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.3 CLCxSEL0 Name: Offset: CLCxSEL0 0x1E12,0x1E1C,0x1E26,0x1E30 Generic CLCx Data 1 Select Register Bit 7 6 5 4 3 2 1 0 D1S[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - D1S[5:0] CLCx Data1 Input Selection bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value n Description Refer to CLC Input Sources for input selections (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 486 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.4 CLCxSEL1 Name: Offset: CLCxSEL1 0x1E13,0x1E1D,0x1E27,0x1E31 Generic CLCx Data 1 Select Register Bit 7 6 5 4 3 2 1 0 D2S[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - D2S[5:0] CLCx Data2 Input Selection bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value n Description Refer to CLC Input Sources for input selections (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 487 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.5 CLCxSEL2 Name: Offset: CLCxSEL2 0x1E14,0x1E1E,0x1E28,0x1E32 Generic CLCx Data 1 Select Register Bit 7 6 5 4 3 2 1 0 D3S[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - D3S[5:0] CLCx Data3 Input Selection bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value n Description Refer to CLC Input Sources for input selections (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 488 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.6 CLCxSEL3 Name: Offset: CLCxSEL3 0x1E15,0x1E1F,0x1E29,0x1E33 Generic CLCx Data 4 Select Register Bit 7 6 5 4 3 2 1 0 D4S[5:0] Access Reset R/W R/W R/W R/W R/W R/W x x x x x x Bits 5:0 - D4S[5:0] CLCx Data4 Input Selection bits Reset States: POR/BOR = xxxxxx All Other Resets = uuuuuu Value n Description Refer to CLC Input Sources for input selections (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 489 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.7 CLCxGLS0 Name: Offset: CLCxGLS0 0x1E16,0x1E20,0x1E2A,0x1E34 CLCx Gate1 Logic Select Register Bit Access Reset 7 6 5 4 3 2 1 0 G1D4T G1D4N G1D3T G1D3N G1D2T G1D2N G1D1T G1D1N R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 1, 3, 5, 7 - G1DyT dyT: Gate1 Data 'y' True (non-inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyT is gated into g1 dyT is not gated into g1 Bits 0, 2, 4, 6 - G1DyN dyN: Gate1 Data 'y' Negated (inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyN is gated into g1 dyN is not gated into g1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 490 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.8 CLCxGLS1 Name: Offset: CLCxGLS1 0x1E17,0x1E21,0x1E2B,0x1E35 CLCx Gate2 Logic Select Register Bit Access Reset 7 6 5 4 3 2 1 0 G2D4T G2D4N G2D3T G2D3N G2D2T G2D2N G2D1T G2D1N R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 1, 3, 5, 7 - G2DyT dyT: Gate2 Data 'y' True (non-inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyT is gated into g2 dyT is not gated into g2 Bits 0, 2, 4, 6 - G2DyN dyN: Gate2 Data 'y' Negated (inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyN is gated into g2 dyN is not gated into g2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 491 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.9 CLCxGLS2 Name: Offset: CLCxGLS2 0x1E18,0x1E22,0x1E2C,0x1E36 CLCx Gate3 Logic Select Register Bit Access Reset 7 6 5 4 3 2 1 0 G3D4T G3D4N G3D3T G3D3N G3D2T G3D2N G3D1T G3D1N R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 1, 3, 5, 7 - G3DyT dyT: Gate3 Data 'y' True (non-inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyT is gated into g3 dyT is not gated into g3 Bits 0, 2, 4, 6 - G3DyN dyN: Gate3 Data 'y' Negated (inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyN is gated into g3 dyN is not gated into g3 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 492 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.10 CLCxGLS3 Name: Offset: CLCxGLS3 0x1E19,0x1E23,0x1E2D,0x1E37 CLCx Gate4 Logic Select Register Bit Access Reset 7 6 5 4 3 2 1 0 G4D4T G4D4N G4D3T G4D3N G4D2T G4D2N G4D1T G4D1N R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 1, 3, 5, 7 - G4DyT dyT: Gate4 Data 'y' True (non-inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyT is gated into g4 dyT is not gated into g4 Bits 0, 2, 4, 6 - G4DyN dyN: Gate4 Data 'y' Negated (inverted) bit Reset States: Default = xxxx POR/BOR = x All Other Resets = u Value 1 0 Description dyN is gated into g4 dyN is not gated into g4 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 493 PIC16(L)F18424/44 (CLC) Configurable Logic Cell 33.8.11 CLCDATA Name: Offset: CLCDATA 0x1E0F CLC Data Ouput Register Mirror copy of Bit 7 6 Access Reset 5 4 3 2 1 0 MLC4OUT MLC3OUT MLC2OUT MLC1OUT R/W R/W R/W R/W 0 0 0 0 Bits 0, 1, 2, 3 - MLCxOUT Mirror copy of CLCx_out bit Value 1 0 Description CLCx_out is 1 CLCx_out is 0 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 494 PIC16(L)F18424/44 Reference Clock Output Module Reference Clock Output Module The reference clock output module provides the ability to send a clock signal to the clock reference output pin (CLKR). The reference clock output can also be routed internally as a signal for other peripherals, such as the Data Signal Modulator (DSM), Memory Scanner, and Timer module. The reference clock output module has the following features: Filename: 10-000261B.vsd Selectable Clock Source Using theWith CLKRCLK Title:* Clock Reference Block Diagram SelectableRegister Clock Source Last Edit: 5/11/2016 * Programmable Clock Divider First Used: PIC18(L)F2x/4x/6xK40 (MVAF,MVAE,MVAB,MVAC,MVAK) * Selectable Duty Cycle Notes: Figure 34-1. Clock Reference Block Diagram Rev. 10-000261B 5/11/2016 DIV EN See CLKRCLK Register Filename: Title: Last Edit: First Used: Notes: Counter Reset Reference Clock Divider 34. 128 111 64 110 32 101 16 100 8 011 10-000264B.vsd 4 010 Clock Reference Timing 5/25/2016 2 001 PIC18(L)F2x/4x/6xK40 (MVAF,MVAE,MVAB,MVAC,MVAK) CLK RxyPPS DC CLKR Duty Cycle PPS To Peripherals 000 EN Figure 34-2. Clock Reference Timing P1 Rev. 10-000264B 5/25/2016 P2 CLKRCLK CLKREN CLKR Output CLKRDIV<2:0> = 001 CLKRDC<1:0> = 10 CLKR Output CLKRDIV<2:0> = 001 CLKRDC<1:0> = 01 (c) 2018 Microchip Technology Inc. Duty Cycle (50%) CLKRCLK/2 Duty Cycle (25%) Datasheet Preliminary DS40002000A-page 495 PIC16(L)F18424/44 Reference Clock Output Module 34.1 Clock Source The clock source of the reference clock peripheral is selected with the CLK bits. The available clock sources are listed in the following table: Table 34-1. CLKR Clock Sources 34.1.1 CLK Clock Source 1111-1011 Reserved 1010 CLC4 OUT 1001 CLC3 OUT 1000 CLC2 OUT 0111 CLC1 OUT 0110 NCO1 OUT 0101 SOSC 0100 MFINTOSC (32 kHz) 0011 MFINTOSC (500 kHz) 0010 LFINTOSC 0001 HFINTOSC (32 MHz) 0000 FOSC Clock Synchronization The CLKR output signal is ensured to be glitch-free when the EN bit is set to start the module and enable the CLKR output. When the reference clock output is disabled, the output signal will be disabled immediately. Clock dividers and clock duty cycles can be changed while the module is enabled but doing so may cause glitches to occur on the output. To avoid possible glitches, clock dividers and clock duty cycles should be changed only when the EN bit is clear. 34.2 Programmable Clock Divider The module takes the clock input and divides it based on the value of the DIV bits. The following configurations are available: * * * * * * * * Base Fosc value FOSC divided by 2 FOSC divided by 4 FOSC divided by 8 FOSC divided by 16 FOSC divided by 32 FOSC divided by 64 FOSC divided by 128 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 496 PIC16(L)F18424/44 Reference Clock Output Module The clock divider values can be changed while the module is enabled. However, in order to prevent glitches on the output, the DIV bits should only be changed when the module is disabled (EN = 0). 34.3 Selectable Duty Cycle The DC bits are used to modify the duty cycle of the output clock. A duty cycle of 0%, 25%, 50%, or 75% can be selected for all clock rates when the DIV value is not 0b000. When DIV=0b000 then the duty cycle defaults to 50% for all values of DC except 0b00 in which case the duty cycle is 0% (constant low output). The duty cycle can be changed while the module is enabled. However, in order to prevent glitches on the output, the DC bits should only be changed when the module is disabled (EN = 0). Important: The DC value at reset is 10. This makes the default duty cycle 50% and not 0%. 34.4 Operation in Sleep Mode The reference clock module continues to operate and provide a signal output in Sleep for all clock source selections except FOSC (CLK=0). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 497 PIC16(L)F18424/44 Reference Clock Output Module 34.5 Register Summary: Reference CLK Offset Name Bit Pos. 0x0895 CLKRCON 7:0 0x0896 CLKRCLK 7:0 34.6 EN DC[1:0] DIV[2:0] CLK[3:0] Register Definitions: Reference Clock Long bit name prefixes for the Reference Clock peripherals are shown in the following table. Refer to the "Long Bit Names" section for more information. Table 34-2. TABLE 5-1: Peripheral Bit Name Prefix CLKR CLKR Related Links Long Bit Names (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 498 PIC16(L)F18424/44 Reference Clock Output Module 34.6.1 CLKRCON Name: Offset: CLKRCON 0x895 Reference Clock Control Register Bit 7 6 5 4 EN Access Reset 3 2 DC[1:0] 1 0 DIV[2:0] R/W R/W R/W R/W R/W R/W 0 1 0 0 0 0 Bit 7 - EN Reference Clock Module Enable bit Value 1 0 Description Reference clock module enabled Reference clock module is disabled Bits 4:3 - DC[1:0] Reference Clock Duty Cycle bits(1) Value 11 10 01 00 Description Clock outputs duty cycle of 75% Clock outputs duty cycle of 50% Clock outputs duty cycle of 25% Clock outputs duty cycle of 0% Bits 2:0 - DIV[2:0] Reference Clock Divider bits Value 111 110 101 100 011 010 001 000 Description Base clock value divided by 128 Base clock value divided by 64 Base clock value divided by 32 Base clock value divided by 16 Base clock value divided by 8 Base clock value divided by 4 Base clock value divided by 2 Base clock value Note: 1. Bits are valid for reference clock divider values of two or larger, the base clock cannot be further divided. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 499 PIC16(L)F18424/44 Reference Clock Output Module 34.6.2 CLKRCLK Name: Offset: CLKRCLK 0x896 Clock Reference Clock Selection MUX Bit 7 6 5 4 3 2 1 0 CLK[3:0] Access Reset R/W R/W R/W R/W 0 0 0 0 Bits 3:0 - CLK[3:0] CLKR Clock Selection bits See the Clock Sources table. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 500 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35. (MSSP) Master Synchronous Serial Port Module The Master Synchronous Serial Port (MSSP) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The MSSP module can operate in one of two modes: * * Serial Peripheral Interface (SPI) Inter-Integrated Circuit (I2C) The SPI interface supports the following modes and features: * * * * * Master mode Slave mode Clock Parity Slave Select Synchronization (Slave mode only) Daisy-chain connection of slave devices The I2C interface supports the following modes and features: * * * * * * * * * * * * * 35.1 Master mode Slave mode Byte NACKing (Slave mode) Limited multi-master support 7-bit and 10-bit addressing Start and Stop interrupts Interrupt masking Clock stretching Bus collision detection General call address matching Address masking Address Hold and Data Hold modes Selectable SDA hold times SPI Mode Overview The Serial Peripheral Interface (SPI) bus is a synchronous serial data communication bus that operates in Full-Duplex mode. Devices communicate in a master/slave environment where the master device initiates the communication. A slave device is controlled through a Chip Select known as Slave Select. The SPI bus specifies four signal connections: * * * * Serial Clock (SCK) Serial Data Out (SDO) Serial Data In (SDI) Slave Select (SS) The following figure shows the block diagram of the MSSP module when operating in SPI mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 501 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-1. MSSP Block Diagram (SPI mode) Rev. 30-000011A 3/31/2017 Data Bus Write Read SSPxBUF Reg SSPxDATPPS SDI PPS SSPSR Reg Shift Clock bit 0 SDO PPS RxyPPS SS SS Control Enable PPS SSPxSSPPS Edge Select SSPxCLKPPS(2) SCK SSPM<3:0> 4 PPS PPS TRIS bit 2 (CKP, CKE) Clock Select Edge Select RxyPPS(1) ( T2_match 2 ) Prescaler TOSC 4, 16, 64 Baud Rate Generator (SSPxADD) Note 1: Output selection for master mode 2: Input selection for slave and master mode The SPI bus operates with a single master device and one or more slave devices. When multiple slave devices are used, an independent Slave Select connection is required from the master device to each slave device. The figure below shows a typical connection between a master device and multiple slave devices. The master selects only one slave at a time. Most slave devices have tri-state outputs so their output signal appears disconnected from the bus when they are not selected. (c)2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 502 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-2. SPI Master and Multiple Slave Connection Rev. 30-000012A 3/31/2017 SPI Master SCK SCK SDO SDI SDI SDO General I/O General I/O SS General I/O SCK SDI SDO SPI Slave #1 SPI Slave #2 SS SCK SDI SDO SPI Slave #3 SS 35.1.1 SPI Mode Registers The MSSP module has five registers for SPI mode operation. These are: * * * * * * MSSP STATUS register (SSPxSTAT) MSSP Control register 1 (SSPxCON1) MSSP Control register 3 (SSPxCON3) MSSP Data Buffer register (SSPxBUF) MSSP Address register (SSPxADD) MSSP Shift register (SSPSR) (Not directly accessible) SSPxCON1 and SSPxSTAT are the control and STATUS registers for SPI mode operation. The SSPxCON1 register is readable and writable. The lower six bits of the SSPxSTAT are read-only. The upper two bits of the SSPxSTAT are read/write. One of the five SPI master modes uses the SSPxADD value to determine the Baud Rate Generator clock frequency. More information on the Baud Rate Generator is available in Baud Rate Generator. SSPSR is the shift register used for shifting data in and out. SSPxBUF provides indirect access to the SSPSR register. SSPxBUF is the buffer register to which data bytes are written, and from which data bytes are read. In receive operations, SSPSR and SSPxBUF together create a buffered receiver. When SSPSR receives a complete byte, it is transferred to SSPxBUF and the SSPxIF interrupt is set. During transmission, the SSPxBUF is not buffered. A write to SSPxBUF will write to both SSPxBUF and SSPSR. 35.2 SPI Mode Operation Transmissions involve two shift registers, eight bits in size, one in the master and one in the slave. With either the master or the slave device, data is always shifted out one bit at a time, with the Most Significant (c)2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 503 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module bit (MSb) shifted out first. At the same time, a new Least Significant bit (LSb) is shifted into the same register. The following figure shows a typical connection between two processors configured as master and slave devices. Figure 35-3. SPI Master/Slave Connection Rev/ 30-000013A 3/31/2017 SPI Master SSPM<3:0> = 00xx = 1010 SPI Slave SSPM<3:0> = 010x SDO SDI Serial Input Buffer (BUF) LSb SCK General I/O Processor 1 SDO SDI Shift Register (SSPSR) MSb Serial Input Buffer (SSPxBUF) Serial Clock Shift Register (SSPSR) MSb LSb SCK Slave Select (optional) SS Processor 2 Data is shifted out of both shift registers on the programmed clock edge and latched on the opposite edge of the clock. The master device transmits information out on its SDO output pin which is connected to, and received by, the slave's SDI input pin. The slave device transmits information out on its SDO output pin, which is connected to, and received by, the master's SDI input pin. To begin communication, the master device first sends out the clock signal. Both the master and the slave devices should be configured for the same clock polarity. The master device starts a transmission by sending out the MSb from its shift register. The slave device reads this bit from that same line and saves it into the LSb position of its shift register. During each SPI clock cycle, a full-duplex data transmission occurs. This means that while the master device is sending out the MSb from its shift register (on its SDO pin) and the slave device is reading this bit and saving it as the LSb of its shift register, that the slave device is also sending out the MSb from its shift register (on its SDO pin) and the master device is reading this bit and saving it as the LSb of its shift register. After eight bits have been shifted out, the master and slave have exchanged register values. If there is more data to exchange, the shift registers are loaded with new data and the process repeats itself. Whether the data is meaningful or not (dummy data), depends on the application software. This leads to three scenarios for data transmission: * * Master sends useful data and slave sends dummy data. Master sends useful data and slave sends useful data. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 504 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module * Master sends dummy data and slave sends useful data. Transmissions may involve any number of clock cycles. When there is no more data to be transmitted, the master stops sending the clock signal and it deselects the slave. Every slave device connected to the bus that has not been selected through its slave select line must disregard the clock and transmission signals and must not transmit out any data of its own. When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits (SSPxCON1<5:0> and SSPxSTAT<7:6>). These control bits allow the following to be specified: * * * * * * * Master mode (SCK is the clock output) Slave mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Data Input Sample Phase (middle or end of data output time) Clock Edge (output data on rising/falling edge of SCK) Clock Rate (Master mode only) Slave Select mode (Slave mode only) To enable the serial port, SSP Enable bit, SSPEN, must be set. To reset or reconfigure SPI mode, clear the SSPEN bit, re-initialize the SSPxCONx registers and then set the SSPEN bit. The SDI, SDO, SCK and SS serial port pins are selected with the PPS controls. For the pins to behave as the serial port function, some must have their data direction bits (in the TRIS register) appropriately programmed as follows: * * * * * * SDI must have corresponding TRIS bit set SDO must have corresponding TRIS bit cleared SCK (Master mode) must have corresponding TRIS bit cleared SCK (Slave mode) must have corresponding TRIS bit set The RxyPPS and SSPxCLKPPS controls must select the same pin SS must have corresponding TRIS bit set Any serial port function that is not desired may be overridden by programming the corresponding data direction (TRIS) register to the opposite value. The MSSP consists of a transmit/receive shift register (SSPSR) and a buffer register (SSPxBUF). The SSPSR shifts the data in and out of the device, MSb first. The SSPxBUF holds the data that was written to the SSPSR until the received data is ready. Once the eight bits of data have been received, that byte is moved to the SSPxBUF register. Then, the Buffer Full Detect bit, BF, and the interrupt flag bit, SSPxIF, are set. This double-buffering of the received data (SSPxBUF) allows the next byte to start reception before reading the data that was just received. Any write to the SSPxBUF register during transmission/ reception of data will be ignored and the write collision detect bit, WCOL, will be set. User software must clear the WCOL bit to allow the following write(s) to the SSPxBUF register to complete successfully. When the application software is expecting to receive valid data, the SSPxBUF should be read before the next byte of data to transfer is written to the SSPxBUF. The Buffer Full bit, BF, indicates when SSPxBUF has been loaded with the received data (transmission is complete). When the SSPxBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI is only a transmitter. Generally, the MSSP interrupt is used to determine when the transmission/reception has completed. If the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 505 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module The SSPSR is not directly readable or writable and can only be accessed by addressing the SSPxBUF register. Additionally, the SSPxSTAT register indicates the various Status conditions. 35.2.1 SPI Master Mode The master can initiate the data transfer at any time because it controls the SCK line. The master determines when the slave (Processor 2, Figure 35-3) is to broadcast data by the software protocol. In Master mode, the data is transmitted/received as soon as the SSPxBUF register is written to. If the SPI is only going to receive, the SDO output could be disabled (programmed as an input). The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed clock rate. As each byte is received, it will be loaded into the SSPxBUF register as if a normal received byte (interrupts and Status bits appropriately set). The clock polarity is selected by appropriately programming the CKP bit and the CKE bit. This then, would give waveforms for SPI communication as shown in Figure 35-4, Figure 35-6, Figure 35-7 and Figure 35-8, where the MSB is transmitted first. In Master mode, the SPI clock rate (bit rate) is user programmable to be one of the following: * * * * * FOSC/4 (or TCY) FOSC/16 (or 4 * TCY) FOSC/64 (or 16 * TCY) Timer2 output/2 FOSC/(4 * (SSPxADD + 1)) Figure 35-4 shows the waveforms for Master mode. When the CKE bit is set, the SDO data is valid before there is a clock edge on SCK. The change of the input sample is shown based on the state of the SMP bit. The time when the SSPxBUF is loaded with the received data is shown. Important: In Master mode the clock signal output to the SCK pin is also the clock signal input to the peripheral. The pin selected for output with the RxyPPS register must also be selected as the peripheral input with the SSPxCLKPPS register. The pin that is selected using the SSPxCLKPPS register should also be made a digital I/O. This is done by clearing the corresponding ANSEL bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 506 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-4. SPI Mode Waveform (Master Mode) Rev. 30-000014A 3/13/2017 Write to SSPxBUF SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) 4 Clock Modes SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) SDO (CKE = 0) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDO (CKE = 1) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDI (SMP = 0) bit 0 bit 7 Input Sample (SMP = 0) SDI (SMP = 1) bit 0 bit 7 Input Sample (SMP = 1) SSPxIF SSPSR to SSPxBUF 35.2.2 SPI Slave Mode In Slave mode, the data is transmitted and received as external clock pulses appear on SCK. When the last bit is latched, the SSPxIF interrupt flag bit is set. Before enabling the module in SPI Slave mode, the clock line must match the proper Idle state. The clock line can be observed by reading the SCK pin. The Idle state is determined by the CKP bit. While in Slave mode, the external clock is supplied by the external clock source on the SCK pin. This external clock must meet the minimum high and low times as specified in the electrical specifications. While in Sleep mode, the slave can transmit/receive data. The shift register is clocked from the SCK pin input and when a byte is received, the device will generate an interrupt. If enabled, the device will wakeup from Sleep. 35.2.3 Daisy-Chain Configuration The SPI bus can sometimes be connected in a daisy-chain configuration. The first slave output is connected to the second slave input, the second slave output is connected to the third slave input, and so on. The final slave output is connected to the master input. Each slave sends out, during a second group of clock pulses, an exact copy of what was received during the first group of clock pulses. The whole (c)2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 507 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module chain acts as one large communication shift register. The daisy-chain feature only requires a single Slave Select line from the master device. The following figure shows the block diagram of a typical daisy-chain connection when operating in SPI mode. Figure 35-5. SPI Daisy-Chain Connection Rev. 30-000015A 3/31/2017 SPI Master SCK SCK SDO SDI SDI General I/O SDO SPI Slave #1 SS SCK SDI SDO SPI Slave #2 SS SCK SDI SDO SPI Slave #3 SS In a daisy-chain configuration, only the most recent byte on the bus is required by the slave. Setting the BOEN bit will enable writes to the SSPxBUF register, even if the previous byte has not been read. This allows the software to ignore data that may not apply to it. 35.2.4 Slave Select Synchronization The Slave Select can also be used to synchronize communication. The Slave Select line is held high until the master device is ready to communicate. When the Slave Select line is pulled low, the slave knows that a new transmission is starting. If the slave fails to receive the communication properly, it will be reset at the end of the transmission, when the Slave Select line returns to a high state. The slave is then ready to receive a new transmission when the Slave Select line is pulled low again. If the Slave Select line is not used, there is a risk that the slave will eventually become out of sync with the master. If the slave misses a bit, it will always be one bit off in future transmissions. Use of the Slave Select line allows the slave and master to align themselves at the beginning of each transmission. The SS pin allows a Synchronous Slave mode. The SPI must be in Slave mode with SS pin control enabled (SSPM = 0100). When the SS pin is low, transmission and reception are enabled and the SDO pin is driven. When the SS pin goes high, the SDO pin is no longer driven, even if in the middle of a transmitted byte and becomes a floating output. External pull-up/pull-down resistors may be desirable depending on the application. Note: 1. When the SPI is in Slave mode with SS pin control enabled (SSPM = 0100), the SPI module will reset if the SS pin is set to VDD. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 508 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 2. 3. When the SPI is used in Slave mode with CKE set; the user must enable SS pin control. While operated in SPI Slave mode the SMP bit must remain clear. When the SPI module resets, the bit counter is forced to `0'. This can be done by either forcing the SS pin to a high level or clearing the SSPEN bit. Figure 35-6. Slave Select Synchronous Waveform Rev. 30-000016A 4/10/2017 SS SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPxBUF Shift register SSPSR and bit count are reset SSPxBUF to SSPSR SDO bit 7 bit 6 bit 7 SDI bit 6 bit 0 bit 0 bit 7 bit 7 Input Sample SSPxIF Interrupt Flag SSPSR to SSPxBUF (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 509 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-7. SPI Mode Waveform (Slave Mode with CKE = 0) Rev. 30-000017A 4/3/2017 SS Optional SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPxBUF Valid SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDI bit 0 bit 7 Input Sample SSPxIF Interrupt Flag SSPSR to SSPxBUF Write Collision detection active (c)2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 510 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-8. SPI Mode Waveform (Slave Mode with CKE = 1) Rev. 30-000018A 4/1/2017 SS Not Optional SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) Write to SSPxBUF Valid SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDI bit 0 bit 7 Input Sample SSPxIF Interrupt Flag SSPSR to SSPxBUF Write Collision detection active 35.2.5 SPI Operation in Sleep Mode In SPI Master mode, module clocks may be operating at a different speed than when in Full-Power mode; in the case of the Sleep mode, all clocks are halted. Special care must be taken by the user when the MSSP clock is much faster than the system clock. In Slave mode, when MSSP interrupts are enabled, after the master completes sending data, an MSSP interrupt will wake the controller from Sleep. If an exit from Sleep mode is not desired, MSSP interrupts should be disabled. In SPI Master mode, when the Sleep mode is selected, all module clocks are halted and the transmission/reception will remain in that state until the device wakes. After the device returns to Run mode, the module will resume transmitting and receiving data. In SPI Slave mode, the SPI Transmit/Receive Shift register operates asynchronously to the device. This allows the device to be placed in Sleep mode and data to be shifted into the SPI Transmit/Receive Shift register. When all eight bits have been received, the MSSP interrupt flag bit will be set and if enabled, will wake the device. 35.3 I2C Mode Overview The Inter-Integrated Circuit (I2C) bus is a multi-master serial data communication bus. Devices communicate in a master/slave environment where the master devices initiate the communication. A (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 511 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module slave device is controlled through addressing. The following two diagrams show block diagrams of the I2C Master and Slave modes, respectively. Figure 35-9. MSSP Block Diagram (I2C Master mode) Rev. 30-000019A 4/3/2017 Internal data bus SSPxDATPPS(1) Read [SSPM<3:0>] Write SDA SDA in SSPxBUF Baud Rate Generator (SSPxADD) Shift Clock RxyPPS(1) PPS Receive Enable (RCEN) SSPxCLKPPS(2) SCL MSb LSb Start bit, Stop bit, Acknowledge Generate (SSPxCON2) Clock Cntl SSPSR PPS Clock arbitrate/BCOL detect (Hold off clock source) PPS PPS RxyPPS(2) SCL in Bus Collision Start bit detect, Stop bit detect Write collision detect Clock arbitration State counter for end of XMIT/RCV Address Match detect Set/Reset: S, P, SSPxSTAT, WCOL, SSPOV Reset SEN, PEN (SSPxCON2) Set SSP1IF, BCL1IF Note 1: SDA pin selections must be the same for input and output 2: SCL pin selections must be the same for input and output (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 512 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-10. MSSP Block Diagram (I2C Slave mode) Rev. 30-000020A 4/3/2017 Internal Data Bus Read Write SSPxCLKPPS(2) SCL SSPxBUF Reg PPS PPS Shift Clock Clock Stretching SSPSR Reg LSb MSb RxyPPS(2) SSPxMSK Reg (1) SSPxDATPPS SDA Addr Match Match Detect PPS SSPxADD Reg PPS Start and Stop bit Detect RxyPPS(1) Set, Reset S, P bits (SSPxSTAT Reg) Note 1: SDA pin selections must be the same for input and output 2: SCL pin selections must be the same for input and output The I2C bus specifies two signal connections: * * Serial Clock (SCL) Serial Data (SDA) Both the SCL and SDA connections are bidirectional open-drain lines, each requiring pull-up resistors for the supply voltage. Pulling the line to ground is considered a logical zero and letting the line float is considered a logical one. The following diagram shows a typical connection between two processors configured as master and slave devices. Figure 35-11. I2C Master/ Slave Connection Rev. 30-000021A 4/3/2017 VDD SCL SCL VDD Master Slave SDA SDA The I2C bus can operate with one or more master devices and one or more slave devices. There are four potential modes of operation for a given device: (c)2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 513 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module * * * * Master Transmit mode (master is transmitting data to a slave) Master Receive mode (master is receiving data from a slave) Slave Transmit mode (slave is transmitting data to a master) Slave Receive mode (slave is receiving data from the master) To begin communication, a master device starts out in Master Transmit mode. The master device sends out a Start bit followed by the address byte of the slave it intends to communicate with. This is followed by a single Read/Write bit, which determines whether the master intends to transmit to or receive data from the slave device. If the requested slave exists on the bus, it will respond with an Acknowledge bit, otherwise known as an ACK. The master then continues in either Transmit mode or Receive mode and the slave continues in the complement, either in Receive mode or Transmit mode, respectively. A Start bit is indicated by a high-to-low transition of the SDA line while the SCL line is held high. Address and data bytes are sent out, Most Significant bit (MSb) first. The Read/Write bit is sent out as a logical one when the master intends to read data from the slave, and is sent out as a logical zero when it intends to write data to the slave. The Acknowledge bit (ACK) is an active-low signal, which holds the SDA line low to indicate to the transmitter that the slave device has received the transmitted data and is ready to receive more. The transition of a data bit is always performed while the SCL line is held low. Transitions that occur while the SCL line is held high are used to indicate Start and Stop bits. If the master intends to write to the slave, then it repeatedly sends out a byte of data, with the slave responding after each byte with an ACK bit. In this example, the master device is in Master Transmit mode and the slave is in Slave Receive mode. If the master intends to read from the slave, then it repeatedly receives a byte of data from the slave, and responds after each byte with an ACK bit. In this example, the master device is in Master Receive mode and the slave is Slave Transmit mode. On the last byte of data communicated, the master device may end the transmission by sending a Stop bit. If the master device is in Receive mode, it sends the Stop bit in place of the last ACK bit. A Stop bit is indicated by a low-to-high transition of the SDA line while the SCL line is held high. In some cases, the master may want to maintain control of the bus and re-initiate another transmission. If so, the master device may send another Start bit in place of the Stop bit or last ACK bit when it is in receive mode. The I2C bus specifies three message protocols; * * * Single message where a master writes data to a slave. Single message where a master reads data from a slave. Combined message where a master initiates a minimum of two writes, or two reads, or a combination of writes and reads, to one or more slaves. When one device is transmitting a logical one, or letting the line float, and a second device is transmitting a logical zero, or holding the line low, the first device can detect that the line is not a logical one. This detection, when used on the SCL line, is called clock stretching. Clock stretching gives slave devices a (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 514 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module mechanism to control the flow of data. When this detection is used on the SDA line, it is called arbitration. Arbitration ensures that there is only one master device communicating at any single time. 35.3.1 Register Definitions: I2C Mode The MSSPx module has seven registers for I2C operation. These are: * * * * * * * * MSSP Status register (SSPxSTAT) MSSP Control register 1 (SSPxCON1) MSSP Control register 2 (SSPxCON2) MSSP Control register 3 (SSPxCON3) Serial Receive/Transmit Buffer register (SSPxBUF) MSSP Address register (SSPxADD) I2C Slave Address Mask register (SSPxMSK) MSSP Shift register (SSPSR) - not directly accessible SSPxCON1, SSPxCON2, SSPxCON3 and SSPxSTAT are the Control and STATUS registers in I2C mode operation. The SSPxCON1, SSPxCON2, and SSPxCON3 registers are readable and writable. The lower six bits of the SSPxSTAT are read-only. The upper two bits of the SSPxSTAT are read/write. SSPSR is the Shift register used for shifting data in or out. SSPxBUF is the buffer register to which data bytes are written to or read from. SSPxADD contains the slave device address when the MSSP is configured in I2C Slave mode. When the MSSP is configured in Master mode, the lower seven bits of SSPxADD act as the Baud Rate Generator reload value. SSPxMSK holds the slave address mask value when the module is configured for 7-Bit Address Masking mode. While it is a separate register, it shares the same SFR address as SSPxADD; it is only accessible when the SSPM<3:0> bits are specifically set to permit access. In receive operations, SSPSR and SSPxBUF together, create a double-buffered receiver. When SSPSR receives a complete byte, it is transferred to SSPxBUF and the SSPxIF interrupt is set. During transmission, the SSPxBUF is not double-buffered. A write to SSPxBUF will write to both SSPxBUF and SSPSR. 35.4 I2C Mode Operation All MSSP I2C communication is byte oriented and shifted out MSb first. Six SFR registers and two (R) interrupt flags interface the module with the PIC microcontroller and user software. Two pins, SDA and SCL, are exercised by the module to communicate with other external I2C devices. 35.4.1 Clock Stretching When a slave device has not completed processing data, it can delay the transfer of more data through the process of clock stretching. An addressed slave device may hold the SCL clock line low after receiving or sending a bit, indicating that it is not yet ready to continue. The master that is communicating with the slave will attempt to raise the SCL line in order to transfer the next bit, but will detect that the clock line has not yet been released. Because the SCL connection is open-drain, the slave has the ability to hold that line low until it is ready to continue communicating. Clock stretching allows receivers that cannot keep up with a transmitter to control the flow of incoming data. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 515 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.4.2 Arbitration Each master device must monitor the bus for Start and Stop bits. If the device detects that the bus is busy, it cannot begin a new message until the bus returns to an Idle state. However, two master devices may try to initiate a transmission on or about the same time. When this occurs, the process of arbitration begins. Each transmitter checks the level of the SDA data line and compares it to the level that it expects to find. The first transmitter to observe that the two levels do not match, loses arbitration, and must stop transmitting on the SDA line. For example, if one transmitter holds the SDA line to a logical one (lets it float) and a second transmitter holds it to a logical zero (pulls it low), the result is that the SDA line will be low. The first transmitter then observes that the level of the line is different than expected and concludes that another transmitter is communicating. The first transmitter to notice this difference is the one that loses arbitration and must stop driving the SDA line. If this transmitter is also a master device, it also must stop driving the SCL line. It then can monitor the lines for a Stop condition before trying to reissue its transmission. In the meantime, the other device that has not noticed any difference between the expected and actual levels on the SDA line continues with its original transmission. It can do so without any complications, because so far, the transmission appears exactly as expected with no other transmitter disturbing the message. Slave Transmit mode can also be arbitrated, when a master addresses multiple slaves, but this is less common. If two master devices are sending a message to two different slave devices at the address stage, the master sending the lower slave address always wins arbitration. When two master devices send messages to the same slave address, and addresses can sometimes refer to multiple slaves, the arbitration process must continue into the data stage. Arbitration usually occurs very rarely, but it is a necessary process for proper multi-master support. 35.4.3 Byte Format All communication in I2C is done in 9-bit segments. A byte is sent from a master to a slave or vice-versa, followed by an Acknowledge bit sent back. After the eighth falling edge of the SCL line, the device outputting data on the SDA changes that pin to an input and reads in an acknowledge value on the next clock pulse. The clock signal, SCL, is provided by the master. Data is valid to change while the SCL signal is low, and sampled on the rising edge of the clock. Changes on the SDA line while the SCL line is high define special conditions on the bus, explained below. 35.4.4 Definition of I2C Terminology There is language and terminology in the description of I2C communication that have definitions specific to I2C. That word usage is defined below and may be used in the rest of this document without explanation. This table was adapted from the Philips I2C specification. TERM Description Transmitter The device which shifts data out onto the bus. Receiver The device which shifts data in from the bus. Master The device that initiates a transfer, generates clock signals and terminates a transfer. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 516 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module TERM Description Slave The device addressed by the master. Multi-master A bus with more than one device that can initiate data transfers. Arbitration Procedure to ensure that only one master at a time controls the bus. Winning arbitration ensures that the message is not corrupted. Synchronization Procedure to synchronize the clocks of two or more devices on the bus. Idle No master is controlling the bus, and both SDA and SCL lines are high. Active Any time one or more master devices are controlling the bus. Addressed Slave Slave device that has received a matching address and is actively being clocked by a master. Matching Address Address byte that is clocked into a slave that matches the value stored in SSPxADD. 35.4.5 Write Request Slave receives a matching address with R/W bit clear, and is ready to clock in data. Read Request Master sends an address byte with the R/W bit set, indicating that it wishes to clock data out of the Slave. This data is the next and all following bytes until a Restart or Stop. Clock Stretching When a device on the bus hold SCL low to stall communication. Bus Collision Any time the SDA line is sampled low by the module while it is outputting and expected high state. SDA and SCL Pins Selection of any I2C mode with the SSPEN bit set, forces the SCL and SDA pins to be open-drain. These pins should be set by the user to inputs by setting the appropriate TRIS bits. Note: 1. Data is tied to output zero when an I2C mode is enabled. 2. Any device pin can be selected for SDA and SCL functions with the PPS peripheral. These functions are bidirectional. The SDA input is selected with the SSPxDATPPS registers. The SCL input is selected with the SSPxCLKPPS registers. Outputs are selected with the RxyPPS registers. It is the user's responsibility to make the selections so that both the input and the output for each function is on the same pin. 35.4.6 SDA Hold Time The hold time of the SDA pin is selected by the SDAHT bit. Hold time is the time SDA is held valid after the falling edge of SCL. Setting the SDAHT bit selects a longer 300 ns minimum hold time and may help on buses with large capacitance. I2C Bus Terms 35.4.7 Start Condition The I2C specification defines a Start condition as a transition of SDA from a high to a low state while SCL line is high. A Start condition is always generated by the master and signifies the transition of the bus from an Idle to an Active state. Figure 35-12 shows wave forms for Start and Stop conditions. A bus collision can occur on a Start condition if the module samples the SDA line low before asserting it low. This does not conform to the I2C Specification that states no bus collision can occur on a Start. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 517 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.4.8 Stop Condition A Stop condition is a transition of the SDA line from low-to-high state while the SCL line is high. Important: At least one SCL low time must appear before a Stop is valid, therefore, if the SDA line goes low then high again while the SCL line stays high, only the Start condition is detected. Figure 35-12. I2C Start and Stop Conditions Rev. 30-000022A 4/3/2017 SDA SCL S Start Condition 35.4.9 P Change of Change of Data Allowed Data Allowed Stop Condition Restart Condition A Restart is valid any time that a Stop would be valid. A master can issue a Restart if it wishes to hold the bus after terminating the current transfer. A Restart has the same effect on the slave that a Start would, resetting all slave logic and preparing it to clock in an address. The master may want to address the same or another slave. Figure 35-13 shows the wave form for a Restart condition. In 10-bit Addressing Slave mode a Restart is required for the master to clock data out of the addressed slave. Once a slave has been fully addressed, matching both high and low address bytes, the master can issue a Restart and the high address byte with the R/W bit set. The slave logic will then hold the clock and prepare to clock out data. After a full match with R/W clear in 10-bit mode, a prior match flag is set and maintained until a Stop condition, a high address with R/W clear, or high address match fails. Figure 35-13. I2C Restart Condition Rev. 30-000023A 4/3/2017 Sr Change of Change of Data Allowed Restart Condition Data Allowed (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 518 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.4.10 Start/Stop Condition Interrupt Masking The SCIE and PCIE bits can enable the generation of an interrupt in Slave modes that do not typically support this function. These bits will have no effect in Slave modes where interrupt on Start and Stop detect are already enabled. 35.4.11 Acknowledge Sequence The ninth SCL pulse for any transferred byte in I2C is dedicated as an Acknowledge. It allows receiving devices to respond back to the transmitter by pulling the SDA line low. The transmitter must release control of the line during this time to shift in the response. The Acknowledge (ACK) is an active-low signal, pulling the SDA line low indicates to the transmitter that the device has received the transmitted data and is ready to receive more. The result of an ACK is placed in the ACKSTAT bit. Slave software, when the AHEN and DHEN bits are set, allow the user to set the ACK value sent back to the transmitter. The ACKDT bit is set/cleared to determine the response. Slave hardware will generate an ACK response if both the AHEN and DHEN bits are clear. However, tf the BF bit or the SSPOV bit are set when a byte is received then the ACK will not be sent by the slave. When the module is addressed, after the eighth falling edge of SCL on the bus, the ACKTIM bit is set. The ACKTIM bit indicates the acknowledge time of the active bus. The ACKTIM Status bit is only active when either the AHEN bit or DHEN bit is enabled. 35.5 I2C Slave Mode Operation The MSSP Slave mode operates in one of four modes selected by the SSPM bits. The modes can be divided into 7-bit and 10-bit Addressing mode. 10-bit Addressing modes operate the same as 7-bit with some additional overhead for handling the larger addresses. Modes with Start and Stop bit interrupts operate the same as the other modes with SSPxIF additionally getting set upon detection of a Start, Restart, or Stop condition. 35.5.1 Slave Mode Addresses The SSPxADD register contains the Slave mode address. The first byte received after a Start or Restart condition is compared against the value stored in this register. If the byte matches, the value is loaded into the SSPxBUF register and an interrupt is generated. If the value does not match, the module goes idle and no indication is given to the software that anything happened. The SSPxMSK register affects the address matching process. See SSP Mask Register for more information. 35.5.1.1 I2C Slave 7-bit Addressing Mode In 7-bit Addressing mode, the LSb of the received data byte is ignored when determining if there is an address match. 35.5.1.2 I2C Slave 10-bit Addressing Mode In 10-bit Addressing mode, the first received byte is compared to the binary value of `1 1 1 1 0 A9 A8 0'. A9 and A8 are the two MSb's of the 10-bit address and stored in bits 2 and 1 of the SSPxADD register. After the acknowledge of the high byte the UA bit is set and SCL is held low until the user updates SSPxADD with the low address. The low address byte is clocked in and all eight bits are compared to the low address value in SSPxADD. Even if there is not an address match; SSPxIF and UA are set, and SCL (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 519 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module is held low until SSPxADD is updated to receive a high byte again. When SSPxADD is updated the UA bit is cleared. This ensures the module is ready to receive the high address byte on the next communication. A high and low address match as a write request is required at the start of all 10-bit addressing communication. A transmission can be initiated by issuing a Restart once the slave is addressed, and clocking in the high address with the R/W bit set. The slave hardware will then acknowledge the read request and prepare to clock out data. This is only valid for a slave after it has received a complete high and low address byte match. 35.5.2 Slave Reception When the R/W bit of a matching received address byte is clear, the R/W bit is cleared. The received address is loaded into the SSPxBUF register and acknowledged. When the overflow condition exists for a received address, then not Acknowledge is given. An overflow condition is defined as either bit BF is set, or bit SSPOV is set. The BOEN bit modifies this operation. For more information see SSPxCON3. An MSSP interrupt is generated for each transferred data byte. Flag bit, SSPxIF, must be cleared by software. When the SEN bit is set, SCL will be held low (clock stretch) following each received byte. The clock must be released by setting the CKP bit, except sometimes in 10-bit mode. See 10-bit Addressing Mode for more detail. 35.5.2.1 7-bit Addressing Reception This section describes a standard sequence of events for the MSSP module configured as an I2C slave in 7-bit Addressing mode. Figure 35-14 and Figure 35-15 is used as a visual reference for this description. This is a step by step process of what typically must be done to accomplish I2C communication. 1. 2. 3. 4. 5. 6. 7. Start bit detected. S bit is set; SSPxIF is set if interrupt on Start detect is enabled. Matching address with R/W bit clear is received. The slave pulls SDA low sending an ACK to the master, and sets SSPxIF bit. Software clears the SSPxIF bit. Software reads received address from SSPxBUF clearing the BF flag. If SEN = 1; Slave software sets CKP bit to release the SCL line. 8. 9. 10. 11. 12. 13. The master clocks out a data byte. Slave drives SDA low sending an ACK to the master, and sets SSPxIF bit. Software clears SSPxIF. Software reads the received byte from SSPxBUF clearing BF. Steps 8-12 are repeated for all received bytes from the master. Master sends Stop condition, setting P bit, and the bus goes idle. 35.5.2.2 7-bit Reception with AHEN and DHEN Slave device reception with AHEN and DHEN set operate the same as without these options with extra interrupts and clock stretching added after the eighth falling edge of SCL. These additional interrupts allow the slave software to decide whether it wants to ACK the receive address or data byte, rather than the hardware. This functionality adds support for PMBusTM that was not present on previous versions of this module. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 520 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module This list describes the steps that need to be taken by slave software to use these options for I2C communication. Figure 35-16 displays a module using both address and data holding. Figure 35-17 includes the operation with the SEN bit of the SSPxCON2 register set. 1. 2. 3. 4. 5. 6. 7. 8. 9. S bit is set; SSPxIF is set if interrupt on Start detect is enabled. Matching address with R/W bit clear is clocked in. SSPxIF is set and CKP cleared after the eighth falling edge of SCL. Slave clears the SSPxIF. Slave can look at the ACKTIM bit to determine if the SSPxIF was after or before the ACK. Slave reads the address value from SSPxBUF, clearing the BF flag. Slave sets ACK value clocked out to the master by setting ACKDT. Slave releases the clock by setting CKP. SSPxIF is set after an ACK, not after a NACK. If SEN = 1, the slave hardware will stretch the clock after the ACK. 10. Slave clears SSPxIF. Important: SSPxIF is still set after the ninth falling edge of SCL even if there is no clock stretching and BF has been cleared. Only if NACK is sent to master is SSPxIF not set 11. 12. 13. 14. 15. SSPxIF set and CKP cleared after eighth falling edge of SCL for a received data byte. Slave looks at ACKTIM bit to determine the source of the interrupt. Slave reads the received data from SSPxBUF clearing BF. Steps 7-14 are the same for each received data byte. Communication is ended by either the slave sending an ACK = 1, or the master sending a Stop condition. If a Stop is sent and Interrupt on Stop Detect is disabled, the slave will only know by polling the P bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 521 (c) 2018 Microchip Technology Inc. SSPOV BF SSPxIF SCL SDA S 1 A7 2 A6 3 A5 4 A4 5 A3 Receiving Address 6 A2 7 A1 8 9 ACK 1 D7 2 D6 4 D4 5 D3 6 D2 7 D1 SSPxBUF is read Cleared by software 3 D5 Receiving Data 8 9 2 First byte of dat a is avai labl e in SSPx BUF 1 D6 4 D4 5 D3 6 D2 7 D1 SSPOV set because SSPxBUF is still full. ACK is not sent. Cleared by software 3 D5 Receiving Data From Slave to Master D0 ACK D7 Figure 35-14. I2C Slave, 7-bit Address, Reception (SEN = 0, AHEN = 0, DHEN = 0) 8 D0 9 P SSPxIF set on 9th falling edge of SCL ACK = 1 Bus Master sends Stop condition Rev. 30-000024A 4/10/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Datasheet Preliminary DS40002000A-page 522 (c) 2018 Microchip Technology Inc. Datasheet Preliminary CKP SSPOV BF SSPxIF 1 SCL S A7 SDA 2 A6 3 A5 4 A4 5 A3 Receive Address 6 A2 7 A1 8 9 R/W=0 ACK SEN 2 D6 3 D5 4 D4 5 D3 6 D2 7 D1 8 D0 CKP is written to `1' in software, releasing SCL SSPxBUF is read Cleared by software Clock is held low until CKP is set to `1' 1 D7 Receive Data Figure 35-15. I2C Slave, 7-bit Address, Reception (SEN = 1, AHEN = 0, DHEN = 0) 9 ACK SEN 3 D5 4 D4 5 D3 6 D2 7 D1 CKP is written to `1' in software, releasing SCL SSPOV set because SSPxBUF is still full. ACK is not sent. Cleared by software 2 D6 First byte of dat a is avai labl e in SSPx BUF 1 D7 Receive Data 8 D0 9 ACK Rev. 30-000025A 4/3/2017 SCL is not held low because ACK= 1 SSPxIF set on 9th falling edge of SCL P Bus Master sends Stop condition PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 523 (c) 2018 Microchip Technology Inc. S Datasheet Preliminary P S ACKTIM CKP ACKDT BF SSPxIF SCL SDA Receiving Address 1 3 5 6 7 8 ACK the received byte Slave software clears ACKDT to Address is read from SSBUF If AHEN = 1: SSPxIF is set 4 ACKTIM set by hardware on 8th falling edge of SCL When AHEN=1: CKP is cleared by hardware and SCL is stretched 2 A7 A6 A5 A4 A3 A2 A1 Receiving Data 9 2 3 4 5 6 7 ACKTIM cleared by hardware in 9th rising edge of SCL When DHEN=1: CKP is cleared by hardware on 8th falling edge of SCL SSPxIF is set on 9th falling edge of SCL, after ACK 1 8 ACK D7 D6 D5 D4 D3 D2 D1 D0 Master Releases SDA to slave for ACK sequence Figure 35-16. I2C Slave, 7-bit Address, Reception (SEN = 0, AHEN = 1, DHEN = 1) Received Data 1 2 4 5 6 ACKTIM set by hardware on 8th falling edge of SCL CKP set by software, SCL is released 8 Slave software sets ACKDT to not ACK 7 Cleared by software 3 D7 D6 D5 D4 D3 D2 D1 D0 Data is read from SSPxBUF 9 ACK 9 P No interrupt after not ACK from Slave ACK=1 Master sends Stop condition Rev. 30-000026A 4/3/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 524 (c) 2018 Microchip Technology Inc. Datasheet Preliminary S P S ACKTIM CKP ACKDT BF SSPxIF SCL SDA R/W = 0 4 5 6 7 8 When AHEN = 1; on the 8th falling edge of SCL of an address byte, CKP is cleared Slave software clears ACKDT to ACK the received byte Received address is loaded into SSPxBUF 2 3 ACKTIM is set by hardware on 8th falling edge of SCL 1 A7 A6 A5 A4 A3 A2 A1 Receiving Address 9 ACK Receive Data 2 3 4 5 6 7 8 ACKTIM is cleared by hardware on 9th rising edge of SCL When DHEN = 1; on the 8th falling edge of SCL of a received data byte, CKP is cleared Received data is available on SSPxBUF Cleared by software 1 D7 D6 D5 D4 D3 D2 D1 D0 Master releases SDA to slave for ACK sequence 9 ACK Figure 35-17. I2C Slave, 7-bit Address, Reception (SEN = 1, AHEN = 1, DHEN = 1) Receive Data 1 3 4 5 6 7 8 Set by software, release SCL Slave sends not ACK SSPxBUF can be read any time before next byte is loaded 2 D7 D6 D5 D4 D3 D2 D1 D0 9 ACK CKP is not cleared if not ACK No interrupt after if not ACK from Slave P Master sends Stop condition Rev. 30-000027A 4/3/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 525 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.5.3 Slave Transmission When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit is set. The received address is loaded into the SSPxBUF register, and an ACK pulse is sent by the slave on the ninth bit. Following the ACK, slave hardware clears the CKP bit and the SCL pin is held low (see Clock Stretching for more detail). By stretching the clock, the master will be unable to assert another clock pulse until the slave is done preparing the transmit data. The transmit data must be loaded into the SSPxBUF register which also loads the SSPSR register. Then the SCL pin should be released by setting the CKP bit. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time. The ACK pulse from the master-receiver is latched on the rising edge of the ninth SCL input pulse. This ACK value is copied to the ACKSTAT bit. If ACKSTAT is set (not ACK), then the data transfer is complete. In this case, when the not ACK is latched by the slave, the slave goes idle and waits for another occurrence of the Start bit. If the SDA line was low (ACK), the next transmit data must be loaded into the SSPxBUF register. Again, the SCL pin must be released by setting bit CKP. An MSSP interrupt is generated for each data transfer byte. The SSPxIF bit must be cleared by software and the SSPxSTAT register is used to determine the status of the byte. The SSPxIF bit is set on the falling edge of the ninth clock pulse. 35.5.3.1 Slave Mode Bus Collision A slave receives a Read request and begins shifting data out on the SDA line. If a bus collision is detected and the SBCDE bit is set, the BCLxIF bit of the PIRx register is set. Once a bus collision is detected, the slave goes idle and waits to be addressed again. User software can use the BCLxIF bit to handle a slave bus collision. 35.5.3.2 7-bit Transmission A master device can transmit a read request to a slave, and then clock data out of the slave. The list below outlines what software for a slave will need to do to accomplish a standard transmission. Figure 35-18 can be used as a reference to this list. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Master sends a Start condition on SDA and SCL. S bit is set; SSPxIF is set if interrupt on Start detect is enabled. Matching address with R/W bit set is received by the Slave setting SSPxIF bit. Slave hardware generates an ACK and sets SSPxIF. SSPxIF bit is cleared by user. Software reads the received address from SSPxBUF, clearing BF. R/W is set so CKP was automatically cleared after the ACK. The slave software loads the transmit data into SSPxBUF. CKP bit is set releasing SCL, allowing the master to clock the data out of the slave. SSPxIF is set after the ACK response from the master is loaded into the ACKSTAT register. SSPxIF bit is cleared. The slave software checks the ACKSTAT bit to see if the master wants to clock out more data. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 526 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Important: 1. If the master ACKs then the clock will be stretched. 2. ACKSTAT is the only bit updated on the rising edge of the ninth SCL clock instead of the falling edge. 13. Steps 9-13 are repeated for each transmitted byte. 14. If the master sends a not ACK; the clock is not held, but SSPxIF is still set. 15. The master sends a Restart condition or a Stop. 16. The slave is no longer addressed. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 527 (c) 2018 Microchip Technology Inc. S Datasheet Preliminary P S D/A R/W ACKSTAT CKP BF SSPxIF SCL SDA 1 2 5 6 7 8 Indicates an address has been received R/W is copied from the matching address byte 9 R/W = 1 Automatic ACK Received address is read from SSPxBUF 4 When R/W is set SCL is always held low after 9th SCL falling edge 3 A7 A6 A5 A4 A3 A2 A1 Receiving Address Transmitting Data Automatic 2 3 4 5 Set by software Data to transmit is loaded into SSPxBUF Cleared by software 1 6 7 8 9 D7 D6 D5 D4 D3 D2 D1 D0 ACK Figure 35-18. I2C Slave, 7-bit Address, Transmission (AHEN = 0) Transmitting Data 2 3 4 5 7 8 CKP is not held for not ACK 6 Masters not ACK is copied to ACKSTAT BF is automatically cleared after 8th falling edge of SCL 1 D7 D6 D5 D4 D3 D2 D1 D0 9 ACK P Master sends Stop condition Rev. 30-000028A 4/3/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 528 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.5.3.3 7-bit Transmission with Address Hold Enabled Setting the AHEN bit enables additional clock stretching and interrupt generation after the eighth falling edge of a received matching address. Once a matching address has been clocked in, CKP is cleared and the SSPxIF interrupt is set. Figure 35-19 displays a standard waveform of a 7-bit address slave transmission with AHEN enabled. 1. 2. 3. Bus starts Idle. Master sends Start condition; the S bit is set; SSPxIF is set if interrupt on Start detect is enabled. Master sends matching address with R/W bit set. After the eighth falling edge of the SCL line the CKP bit is cleared and SSPxIF interrupt is generated. 4. Slave software clears SSPxIF. 5. Slave software reads the ACKTIM, R/W and D/A bits to determine the source of the interrupt. 6. Slave reads the address value from the SSPxBUF register clearing the BF bit. 7. Slave software decides from this information if it wishes to ACK or not ACK and sets the ACKDT bit accordingly. 8. Slave sets the CKP bit releasing SCL. 9. Master clocks in the ACK value from the slave. 10. Slave hardware automatically clears the CKP bit and sets SSPxIF after the ACK if the R/W bit is set. 11. Slave software clears SSPxIF. 12. Slave loads value to transmit to the master into SSPxBUF setting the BF bit. Important: SSPxBUF cannot be loaded until after the ACK. 13. 14. 15. 16. 17. Slave sets the CKP bit releasing the clock. Master clocks out the data from the slave and sends an ACK value on the ninth SCL pulse. Slave hardware copies the ACK value into the ACKSTAT bit. Steps 10-15 are repeated for each byte transmitted to the master from the slave. If the master sends a not ACK the slave releases the bus allowing the master to send a Stop and end the communication. Important: Master must send a not ACK on the last byte to ensure that the slave releases the SCL line to receive a Stop. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 529 (c) 2018 Microchip Technology Inc. Datasheet Preliminary D/A R/W ACKTIM CKP ACKSTAT ACKDT BF SSPxIF SCL SDA S 2 4 5 6 7 8 Slave clears ACKDT to ACK address ACKTIM is set on 8th falling edge of SCL 9 ACK When R/W = 1; CKP is always cleared after ACK R/W = 1 Received address is read from SSPxBUF 3 When AHEN = 1; CKP is cleared by hardware after receiving matching address. 1 A7 A6 A5 A4 A3 A2 A1 Receiving Address 3 4 5 6 Cleared by software 2 Set by software, releases SCL Data to transmit is loaded into SSPxBUF 1 7 8 9 Automatic ACK D7 D6 D5 D4 D3 D2 D1 D0 Transmitting Data ACKTIM is cleared on 9th rising edge of SCL Automatic Master releases SDA to slave for ACK sequence Figure 35-19. I2C Slave, 7-bit Address, Transmission (AHEN = 1) 1 3 4 5 6 7 after not ACK CKP not cleared Master's ACK response is copied to SSPxSTAT BF is automatically cleared after 8th falling edge of SCL 2 8 D7 D6 D5 D4 D3 D2 D1 D0 Transmitting Data 9 ACK P Master sends Stop condition Rev. 30-00029A 4/10/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 530 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.5.4 Slave Mode 10-bit Address Reception This section describes a standard sequence of events for the MSSP module configured as an I2C slave in 10-bit Addressing mode. Figure 35-20 is used as a visual reference for this description. This is a step by step process of what must be done by slave software to accomplish I2C communication. 1. 2. 3. 4. 5. 6. 7. 8. Bus starts Idle. Master sends Start condition; S bit is set; SSPxIF is set if interrupt on Start detect is enabled. Master sends matching high address with R/W bit clear; UA bit is set. Slave sends ACK and SSPxIF is set. Software clears the SSPxIF bit. Software reads received address from SSPxBUF clearing the BF flag. Slave loads low address into SSPxADD, releasing SCL. Master sends matching low address byte to the slave; UA bit is set. Important: Updates to the SSPxADD register are not allowed until after the ACK sequence. 9. Slave sends ACK and SSPxIF is set. Important: If the low address does not match, SSPxIF and UA are still set so that the slave software can set SSPxADD back to the high address. BF is not set because there is no match. CKP is unaffected. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 35.5.5 Slave clears SSPxIF. Slave reads the received matching address from SSPxBUF clearing BF. Slave loads high address into SSPxADD. Master clocks a data byte to the slave and clocks out the slaves ACK on the ninth SCL pulse; SSPxIF is set. If SEN bit is set, CKP is cleared by hardware and the clock is stretched. Slave clears SSPxIF. Slave reads the received byte from SSPxBUF clearing BF. If SEN is set the slave sets CKP to release the SCL. Steps 13-17 repeat for each received byte. Master sends Stop to end the transmission. 10-bit Addressing with Address or Data Hold Reception using 10-bit addressing with AHEN or DHEN set is the same as with 7-bit modes. The only difference is the need to update the SSPxADD register using the UA bit. All functionality, specifically when the CKP bit is cleared and SCL line is held low are the same. Figure 35-21 can be used as a reference of a slave in 10-bit addressing with AHEN set. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 531 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-22 shows a standard waveform for a slave transmitter in 10-bit Addressing mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 532 (c) 2018 Microchip Technology Inc. Datasheet Preliminary CKP UA BF SSPxIF SCL SDA S 1 1 2 1 5 6 7 0 A9 A8 8 Set by hardware on 9th falling edge 4 1 When UA = 1; SCL is held low 9 ACK If address matches SSPxADD it is loaded into SSPxBUF 3 1 Receive First Address Byte 1 3 4 5 6 7 8 Software updates SSPxADD and releases SCL 2 9 A7 A6 A5 A4 A3 A2 A1 A0 ACK Receive Second Address Byte Receive Data 1 3 4 5 6 7 8 9 1 3 4 5 6 7 Data is read from SSPxBUF SCL is held low while CKP = 0 2 8 9 D7 D6 D5 D4 D3 D2 D1 D0 ACK Receive Data Set by software, When SEN = 1; releasing SCL CKP is cleared after 9th falling edge of received byte Receive address is read from SSPxBUF Cleared by software 2 D7 D6 D5 D4 D3 D2 D1 D0 ACK Figure 35-20. I2C Slave, 10-bit Address, Reception (SEN = 1, AHEN = 0, DHEN = 0) P Master sends Stop condition Rev. 30-000030A 4/3/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 533 (c) 2018 Microchip Technology Inc. Datasheet Preliminary ACKTIM CKP UA ACKDT BF SSPxIF 1 SCL S 1 SDA 2 1 5 0 6 A9 7 A8 Set by hardware on 9th falling edge 4 1 8 R/W = 0 ACKTIM is set by hardware on 8th falling edge of SCL If when AHEN = 1; on the 8th falling edge of SCL of an address byte, CKP is cleared Slave software clears ACKDT to ACK the received byte 3 1 Receive First Address Byte 9 ACK UA 2 3 A5 4 A4 6 A2 7 A1 Update to SSPxADD is not allowed until 9th falling edge of SCL SSPxBUF can be read anytime before the next received byte 5 A3 Receive Second Address Byte A6 Cleared by software 1 A7 8 A0 Figure 35-21. I2C Slave, 10-bit Address, Reception (SEN = 0, AHEN = 1, DHEN = 0) 9 ACK UA 2 D6 3 D5 4 D4 6 D2 Set CKP with software releases SCL 7 D1 Update of SSPxADD, clears UA and releases SCL 5 D3 Receive Data Cleared by software 1 D7 8 9 2 D6 D5 Received data is read from SSPxBUF 1 D0 ACK D7 Receive Data Rev. 30-000031A 4/3/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 534 (c) 2018 Microchip Technology Inc. Datasheet Preliminary D/A R/W ACKSTAT CKP UA BF SSPxIF 4 5 6 7 Set by hardware 3 Indicates an address has been received UA indicates SSPxADD must be updated SSPxBUF loaded with received address 2 8 9 1 SCL S Receiving Address R/W = 0 1 1 1 1 0 A9 A8 ACK SDA 3 4 5 6 7 8 After SSPxADD is updated, UA is cleared and SCL is released Cleared by software 2 9 1 4 5 6 7 8 Set by hardware 2 3 R/W is copied from the matching address byte When R/W = 1; CKP is cleared on 9th falling edge of SCL High address is loaded back into SSPxADD Received address is read from SSPxBUF Sr 1 1 1 1 0 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ACK 1 Receive First Address Byte Receiving Second Address Byte Master sends Restart event Figure 35-22. I2C Slave, 10-bit Address, Transmission (SEN = 0, AHEN = 0, DHEN = 0) 9 ACK 2 3 4 5 6 7 8 Masters not ACK is copied Set by software releases SCL Data to transmit is loaded into SSPxBUF 1 D7 D6 D5 D4 D3 D2 D1 D0 Transmitting Data Byte 9 P Master sends Stop condition ACK = 1 Master sends not ACK Rev. 30-000032A 4/3/2017 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 535 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.5.6 Clock Stretching Clock stretching occurs when a device on the bus holds the SCL line low, effectively pausing communication. The slave may stretch the clock to allow more time to handle data or prepare a response for the master device. A master device is not concerned with stretching as anytime it is active on the bus and not transferring data it is stretching. Any stretching done by a slave is invisible to the master software and handled by the hardware that generates SCL. The CKP bit is used to control stretching in software. Any time the CKP bit is cleared, the module will wait for the SCL line to go low and then hold it. Setting CKP will release SCL and allow more communication. 35.5.6.1 Normal Clock Stretching Following an ACK if the R/W bit is set, a read request, the slave hardware will clear CKP. This allows the slave time to update SSPxBUF with data to transfer to the master. If the SEN bit is set, the slave hardware will always stretch the clock after the ACK sequence. Once the slave is ready; CKP is set by software and communication resumes. Important: 1. The BF bit has no effect on if the clock will be stretched or not. This is different than previous versions of the module that would not stretch the clock, clear CKP, if SSPxBUF was read before the ninth falling edge of SCL. 2. Previous versions of the module did not stretch the clock for a transmission if SSPxBUF was loaded before the ninth falling edge of SCL. It is now always cleared for read requests. 35.5.6.2 10-bit Addressing Mode In 10-bit Addressing mode, when the UA bit is set, the clock is always stretched. This is the only time the SCL is stretched without CKP being cleared. SCL is released immediately after a write to SSPxADD. Important: Previous versions of the module did not stretch the clock if the second address byte did not match. 35.5.6.3 Byte NACKing When the AHEN bit is set; CKP is cleared by hardware after the eighth falling edge of SCL for a received matching address byte. When the DHEN bit is set; CKP is cleared after the eighth falling edge of SCL for received data. Stretching after the eighth falling edge of SCL allows the slave to look at the received address or data and decide if it wants to ACK the received data. 35.5.7 Clock Synchronization and the CKP bit Any time the CKP bit is cleared, the module will wait for the SCL line to go low and then hold it. However, clearing the CKP bit will not assert the SCL output low until the SCL output is already sampled low. Therefore, the CKP bit will not assert the SCL line until an external I2C master device has already asserted the SCL line. The SCL output will remain low until the CKP bit is set and all other devices on the I2C bus have released SCL. This ensures that a write to the CKP bit will not violate the minimum high time requirement for SCL (see the following figure). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 536 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-23. Clock Synchronization Timing Rev. 30-000033A 4/3/2017 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 SDA DX - 1 DX SCL Master device asserts clock CKP Master device releases clock WR SSPxCON1 35.5.8 General Call Address Support The addressing procedure for the I2C bus is such that the first byte after the Start condition usually determines which device will be the slave addressed by the master device. The exception is the general call address which can address all devices. When this address is used, all devices should, in theory, respond with an acknowledge. The general call address is a reserved address in the I2C protocol, defined as address 0x00. When the GCEN bit is set, the slave module will automatically ACK the reception of this address regardless of the value stored in SSPxADD. After the slave clocks in an address of all zeros with the R/W bit clear, an interrupt is generated and slave software can read SSPxBUF and respond. The following figure shows a general call reception sequence. Figure 35-24. Slave Mode General Call Address Sequence Rev. 30-000034A 4/3/2017 Address is compared to General Call Address after ACK, set interrupt R/W = 0 ACK D7 General Call Address SDA SCL S 1 2 3 4 5 6 7 8 9 1 Receiving Data ACK D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 9 SSPxIF BF (SSPxSTAT<0>) Cleared by software GCEN (SSPxCON2<7>) SSPxBUF is read '1' In 10-bit Address mode, the UA bit will not be set on the reception of the general call address. The slave will prepare to receive the second byte as data, just as it would in 7-bit mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 537 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module If the AHEN bit is set, just as with any other address reception, the slave hardware will stretch the clock after the eighth falling edge of SCL. The slave must then set its ACKEN value and release the clock with communication progressing as it would normally. 35.5.9 SSP Mask Register An SSP Mask register (SSPxMSK) is available in I2C Slave mode as a mask for the value held in the SSPSR register during an address comparison operation. A zero (`0') bit in the SSPxMSK register has the effect of making the corresponding bit of the received address a "don't care". This register is reset to all `1's upon any Reset condition and, therefore, has no effect on standard SSP operation until written with a mask value. The SSP Mask register is active during: * * 35.6 7-bit Address mode: address compare of A<7:1>. 10-bit Address mode: address compare of A<7:0> only. The SSP mask has no effect during the reception of the first (high) byte of the address. I2C Master Mode Master mode is enabled by setting and clearing the appropriate SSPM bits and setting the SSPEN bit. In Master mode, the SDA and SCK pins must be configured as inputs. The MSSP peripheral hardware will override the output driver TRIS controls when necessary to drive the pins low. Master mode of operation is supported by interrupt generation on the detection of the Start and Stop conditions. The Stop (P) and Start (S) bits are cleared from a Reset or when the MSSP module is disabled. Control of the I2C bus may be taken when the P bit is set, or the bus is Idle. In Firmware Controlled Master mode, user code conducts all I2C bus operations based on Start and Stop bit condition detection. Start and Stop condition detection is the only active circuitry in this mode. All other communication is done by the user software directly manipulating the SDA and SCL lines. The following events will cause the SSP Interrupt Flag bit, SSPxIF, to be set (SSP interrupt, if enabled): * * * * * Start condition detected Stop condition detected Data transfer byte transmitted/received Acknowledge transmitted/received Repeated Start generated Important: 1. The MSSP module, when configured in I2C Master mode, does not allow queuing of events. For instance, the user is not allowed to initiate a Start condition and immediately write the SSPxBUF register to initiate transmission before the Start condition is complete. In this case, the SSPxBUF will not be written to and the WCOL bit will be set, indicating that a write to the SSPxBUF did not occur. 2. Master mode suspends Start/Stop detection when sending the Start/Stop condition by means of the SEN/PEN control bits. The SSPxIF bit is set at the end of the Start/Stop generation when hardware clears the control bit. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 538 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.6.1 I2C Master Mode Operation The master device generates all of the serial clock pulses and the Start and Stop conditions. A transfer is ended with a Stop condition or with a Repeated Start condition. Since the Repeated Start condition is also the beginning of the next serial transfer, the I2C bus will not be released. In Master Transmitter mode, serial data is output through SDA, while SCL outputs the serial clock. The first byte transmitted contains the slave address of the receiving device (7 bits) and the R/W bit. In this case, the R/W bit will be logic `0'. Serial data is transmitted eight bits at a time. After each byte is transmitted, an Acknowledge bit is received. Start and Stop conditions are output to indicate the beginning and the end of a serial transfer. In Master Receive mode, the first byte transmitted contains the slave address of the transmitting device (7 bits) and the R/W bit. In this case, the R/W bit will be logic `1'. Thus, the first byte transmitted is a 7-bit slave address followed by a `1' to indicate the receive bit. Serial data is received via SDA, while SCL outputs the serial clock. Serial data is received eight bits at a time. After each byte is received, an Acknowledge bit is transmitted. Start and Stop conditions indicate the beginning and end of transmission. A Baud Rate Generator is used to set the clock frequency output on SCL. See Baud Rate Generator for more detail. 35.6.2 Clock Arbitration Clock arbitration occurs when the master, during any receive, transmit or Repeated Start/Stop condition, releases the SCL pin (SCL allowed to float high). When the SCL pin is allowed to float high, the Baud Rate Generator (BRG) is suspended from counting until the SCL pin is actually sampled high. When the SCL pin is sampled high, the Baud Rate Generator is reloaded with the contents of SSPxADD and begins counting. This ensures that the SCL high time will always be at least one BRG rollover count in the event that the clock is held low by an external device as shown in the following figure. Figure 35-25. Baud Rate Generator Timing with Clock Arbitration Rev. 30-000035A 4/3/2017 SDA DX - 1 DX SCL deasserted but slave holds SCL low (clock arbitration) SCL allowed to transition high SCL BRG decrements on Q2 and Q4 cycles BRG Value 03h 02h 01h 00h (hold off) 03h 02h SCL is sampled high, reload takes place and BRG starts its count BRG Reload 35.6.3 WCOL Status Flag If the user writes the SSPxBUF when a Start, Restart, Stop, Receive or Transmit sequence is in progress, the WCOL bit is set and the contents of the buffer are unchanged (the write does not occur). Any time the WCOL bit is set it indicates that an action on SSPxBUF was attempted while the module was not idle. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 539 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Important: Because queuing of events is not allowed, writing to the lower five bits of SSPxCON2 is disabled until the Start condition is complete. 35.6.4 I2C Master Mode Start Condition Timing To initiate a Start condition (Figure 35-26), the user sets the SEN Start Enable bit. If the SDA and SCL pins are sampled high, the Baud Rate Generator is reloaded with the contents of SSPxADD and starts its count. If SCL and SDA are both sampled high when the Baud Rate Generator times out (TBRG), the SDA pin is driven low. The action of the SDA being driven low while SCL is high is the Start condition and causes the S bit to be set. Following this, the Baud Rate Generator is reloaded with the contents of SSPxADD and resumes its count. When the Baud Rate Generator times out (TBRG), the SEN bit will be automatically cleared by hardware; the Baud Rate Generator is suspended, leaving the SDA line held low and the Start condition is complete. Important: 1. If at the beginning of the Start condition, the SDA and SCL pins are already sampled low, or if during the Start condition, the SCL line is sampled low before the SDA line is driven low, a bus collision occurs, the Bus Collision Interrupt Flag, BCLxIF, is set, the Start condition is aborted and the I2C module is reset into its Idle state. 2. The Philips I2C specification states that a bus collision cannot occur on a Start. Figure 35-26. First Start Bit Timing Rev. 30-000036A 4/3/2017 Set S bit (SSPxSTAT<3>) Write to SEN bit occurs here At completion of Start bit, hardware clears SEN bit a nd set s SSPx I F bi t SDA = 1, SCL = 1 TBRG TBRG Write to SSPxBUF occurs here SDA 1st bit 2nd bit TBRG SCL S 35.6.5 TBRG I2C Master Mode Repeated Start Condition Timing A Repeated Start condition (Figure 35-27) occurs when the RSEN bit is programmed high and the master state machine is no longer active. When the RSEN bit is set, the SCL pin is asserted low. When the SCL pin is sampled low, the Baud Rate Generator is loaded and begins counting. The SDA pin is released (brought high) for one Baud Rate Generator count (TBRG). When the Baud Rate Generator times out, if SDA is sampled high, the SCL pin will be deasserted (brought high). When SCL is sampled high, the Baud Rate Generator is reloaded and begins counting. SDA and SCL must be sampled high for one TBRG. This action is then followed by assertion of the SDA pin (SDA = 0) for one TBRG while SCL is high. SCL is asserted low. Following this, the RSEN bit will be automatically cleared and the Baud Rate Generator will not be reloaded, leaving the SDA pin held low. As soon as a Start condition is detected on (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 540 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module the SDA and SCL pins, the S bit will be set. The SSPxIF bit will not be set until the Baud Rate Generator has timed out. Important: 1. If RSEN is programmed while any other event is in progress, it will not take effect. 2. A bus collision during the Repeated Start condition occurs if: - SDA is sampled low when SCL goes from low-to-high. - SCL goes low before SDA is asserted low. This may indicate that another master is attempting to transmit a data `1'. Figure 35-27. Repeated Start Condition Waveform Rev. 30-000037A 4/10/2017 S bit set by hardware Write to SSPxCON2 occurs here SDA = 1, SCL (no change) At completion of Start bit, hardware clears the RSEN bit and sets SSPxIF SDA = 1, SCL = 1 TBRG TBRG TBRG 1st bit SDA Write to SSPxBUF occurs here TBRG SCL Sr TBRG Repeated Start 35.6.6 I2C Master Mode Transmission Transmission of a data byte, a 7-bit address or the other half of a 10-bit address is accomplished by simply writing a value to the SSPxBUF register. This action will set the Buffer Full flag bit, BF, and allow the Baud Rate Generator to begin counting and start the next transmission. Each bit of address/data will be shifted out onto the SDA pin after the falling edge of SCL is asserted. SCL is held low for one Baud Rate Generator rollover count (TBRG). Data should be valid before SCL is released high. When the SCL pin is released high, it is held that way for TBRG. The data on the SDA pin must remain stable for that duration and some hold time after the next falling edge of SCL. After the eighth bit is shifted out (the falling edge of the eighth clock), the BF flag is cleared and the master releases SDA. This allows the slave device being addressed to respond with an ACK bit during the ninth bit time if an address match occurred, or if data was received properly. The status of ACK is written into the ACKSTAT bit on the rising edge of the ninth clock. If the master receives an Acknowledge, the Acknowledge Status bit, ACKSTAT, is cleared. If not, the bit is set. After the ninth clock, the SSPxIF bit is set and the master clock (Baud Rate Generator) is suspended until the next data byte is loaded into the SSPxBUF, leaving SCL low and SDA unchanged (Figure 35-28). After the write to the SSPxBUF, each bit of the address will be shifted out on the falling edge of SCL until all seven address bits and the R/W bit are completed. On the falling edge of the eighth clock, the master will release the SDA pin, allowing the slave to respond with an Acknowledge. On the falling edge of the ninth clock, the master will sample the SDA pin to see if the address was recognized by a slave. The status of the ACK bit is loaded into the ACKSTAT Status bit of the SSPxCON2 register. Following the falling edge of the ninth clock transmission of the address, the SSPxIF is set, the BF flag is cleared and (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 541 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module the Baud Rate Generator is turned off until another write to the SSPxBUF takes place, holding SCL low and allowing SDA to float. 35.6.6.1 BF Status Flag In Transmit mode, the BF bit is set when the CPU writes to SSPxBUF and is cleared when all eight bits are shifted out. 35.6.6.2 WCOL Status Flag If the user writes the SSPxBUF when a transmit is already in progress (i.e., SSPSR is still shifting out a data byte), the WCOL bit is set and the contents of the buffer are unchanged (the write does not occur). The WCOL bit must be cleared by software before the next transmission. 35.6.6.3 ACKSTAT Status Flag In Transmit mode, the ACKSTAT bit is cleared when the slave has sent an Acknowledge (ACK = 0) and is set when the slave does not Acknowledge (ACK = 1). A slave sends an Acknowledge when it has recognized its address (including a general call), or when the slave has properly received its data. 35.6.6.4 Typical transmit sequence: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. The user generates a Start condition by setting the SEN bit. SSPxIF is set by hardware on completion of the Start. SSPxIF is cleared by software. The MSSP module will wait the required start time before any other operation takes place. The user loads the SSPxBUF with the slave address to transmit. Address is shifted out the SDA pin until all eight bits are transmitted. Transmission begins as soon as SSPxBUF is written to. The MSSP module shifts in the ACK bit from the slave device and writes its value into the ACKSTAT bit. The MSSP module generates an interrupt at the end of the ninth clock cycle by setting the SSPxIF bit. The user loads the SSPxBUF with eight bits of data. Data is shifted out the SDA pin until all eight bits are transmitted. The MSSP module shifts in the ACK bit from the slave device and writes its value into the ACKSTAT bit. Steps 8-11 are repeated for all transmitted data bytes. The user generates a Stop or Restart condition by setting the PEN or RSEN bits. Interrupt is generated once the Stop/Restart condition is complete. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 542 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-28. I2C Master Mode Waveform (Transmission, 7 or 10-bit Address) Rev. 30-000038A 4/3/2017 Write SSPxCON2<0> SEN = 1 Start condition begins From slave, clear ACKSTAT bit SSPxCON2<6> SEN = 0 A7 A6 A5 A4 A3 A2 Transmitting Data or Second Half of 10-bit Address R/W = 0 Transmit Address to Slave SDA ACKSTAT in SSPxCON2 = 1 ACK = 0 A1 ACK D7 D6 D5 D4 D3 D2 D1 D0 1 SCL held low while CPU responds to SSPxIF 2 3 4 5 6 7 8 SSPxBUF written with 7-bit address and R/W start transmit SCL 1 S 2 3 4 5 6 7 8 9 9 P SSPxIF Cleared by software service routine from SSP interrupt Cleared by software Cleared by software BF (SSPxSTAT<0>) SSPxBUF is written by software SSPxBUF written SEN After Start condition, SEN cleared by hardware PEN R/W 35.6.7 I2C Master Mode Reception Master mode reception (Figure 35-29) is enabled by programming the RCEN Receive Enable bit. Important: The MSSP module must be in an Idle state before the RCEN bit is set or the RCEN bit will be disregarded. The Baud Rate Generator begins counting and on each rollover, the state of the SCL pin changes (highto-low/low-to-high) and data is shifted into the SSPSR. After the falling edge of the eighth clock all the following events occur: * The receive enable flag is automatically cleared * The contents of the SSPSR are loaded into the SSPxBUF * The BF flag bit is set * * * The SSPxIF flag bit is set The Baud Rate Generator is suspended from counting The SCL pin is held low The MSSP is now in Idle state awaiting the next command. When the buffer is read by the CPU, the BF flag bit is automatically cleared. The user can then send an Acknowledge bit at the end of reception by setting the Acknowledge Sequence Enable, ACKEN bit. 35.6.7.1 BF Status Flag In receive operation, the BF bit is set when an address or data byte is loaded into SSPxBUF from SSPSR. It is cleared when the SSPxBUF register is read. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 543 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.6.7.2 SSPOV Status Flag In receive operation, the SSPOV bit is set when eight bits are received into the SSPSR while the BF flag bit is already set from a previous reception. 35.6.7.3 WCOL Status Flag If the user writes the SSPxBUF when a receive is already in progress (i.e., SSPSR is still shifting in a data byte), the WCOL bit is set and the contents of the buffer are unchanged (the write does not occur). 35.6.7.4 Typical Receive Sequence: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. The user generates a Start condition by setting the SEN bit. SSPxIF is set by hardware on completion of the Start. SSPxIF is cleared by software. User writes SSPxBUF with the slave address to transmit and the R/W bit set. Address is shifted out the SDA pin until all eight bits are transmitted. Transmission begins as soon as SSPxBUF is written to. The MSSP module shifts in the ACK bit from the slave device and writes its value into the ACKSTAT bit. The MSSP module generates an interrupt at the end of the ninth clock cycle by setting the SSPxIF bit. User sets the RCEN bit and the master clocks in a byte from the slave. After the eighth falling edge of SCL, SSPxIF and BF are set. Master clears SSPxIF and reads the received byte from SSPUF which clears BF. Master sets the ACK value to be sent to slave in the ACKDT bit and initiates the ACK by setting the ACKEN bit. Master's ACK is clocked out to the slave and SSPxIF is set. User clears SSPxIF. Steps 8-13 are repeated for each received byte from the slave. Master sends a not ACK or Stop to end communication. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 544 (c) 2018 Microchip Technology Inc. S Datasheet Preliminary RCEN ACKEN SSPOV BF (SSPxSTAT<0>) SDA = 0, SCL = 1 while CPU responds to SSPxIF SSPxIF SCL SDA 1 A7 2 4 5 6 Cleared by software 3 A6 A5 A4 A3 A2 Transmit Address to Slave 7 8 9 ACK Receiving Data from Slave 2 3 5 6 7 8 D0 9 ACK Receiving Data from Slave 2 3 4 RCEN cleared automatically 5 6 7 Cleared by software Set SSPxIF interrupt at end of Acknowledge sequence Data shifted in on falling edge of CLK 1 ACK from Master SDA = ACKDT = 0 Cleared in software Set SSPxIF at end of receive 9 ACK is not sent ACK RCEN cleared automatically P Rev. 30-000039A 4/3/2017 Set SSPxIF interrupt at end of Acknowledge sequence Bus master terminates transfer Set P bit (SSPxSTAT<4>) and SSPxIF PEN bit = 1 written here SSPOV is set because SSPxBUF is still full 8 D0 RCEN cleared automatically Set ACKEN, start Acknowledge sequence SDA = ACKDT = 1 D7 D6 D5 D4 D3 D2 D1 Last bit is shifted into SSPSR and contents are unloaded into SSPxBUF Cleared by software Set SSPxIF interrupt at end of receive 4 Cleared by software 1 D7 D6 D5 D4 D3 D2 D1 Master configured as a receiver by programming SSPxCON2<3> (RCEN = 1) A1 R/W RCEN = 1, start next receive ACK from Master SDA = ACKDT = 0 Write to SSPxCON2<4> to start Acknowledge sequence SDA = ACKDT (SSPxCON2<5>) = 0 Master configured as a receiver by programming SSPxCON2<3> (RCEN = 1) SEN = 0 Write to SSPxBUF occurs here, RCEN cleared ACK from Slave automatically start XMIT Write to SSPxCON2<0>(SEN = 1), begin Start condition Figure 35-29. I2C Master Mode Waveform (Reception, 7-bit Address) PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module DS40002000A-page 545 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.6.8 Acknowledge Sequence Timing An Acknowledge sequence is enabled by setting the Acknowledge Sequence Enable ACKEN bit. When this bit is set, the SCL pin is pulled low and the contents of the Acknowledge data bit are presented on the SDA pin. If the user wishes to generate an Acknowledge, then the ACKDT bit should be cleared. If not, the user should set the ACKDT bit before starting an Acknowledge sequence. The Baud Rate Generator then counts for one rollover period (TBRG) and the SCL pin is deasserted (pulled high). When the SCL pin is sampled high (clock arbitration), the Baud Rate Generator counts for TBRG. The SCL pin is then pulled low. Following this, the ACKEN bit is automatically cleared, the Baud Rate Generator is turned off and the MSSP module then goes into Idle mode. Figure 35-30. Acknowledge Sequence Waveform Acknowledge sequence starts here, write to SSPxCON2 ACKEN = 1, ACKDT = 0 ACKEN automatically cleared TBRG TBRG SDA ACK D0 SCL Rev. 30-000040A 4/3/2017 8 9 SSPxIF SSPxIF set at the end of receive Cleared in software Cleared in software SSPxIF set at the end of Acknowledge sequence Note: TBRG = one Baud Rate Generator period. 35.6.8.1 Acknowledge Write Collision If the user writes the SSPxBUF when an Acknowledge sequence is in progress, then the WCOL bit is set and the contents of the buffer are unchanged (the write does not occur). 35.6.9 Stop Condition Timing A Stop bit is asserted on the SDA pin at the end of a receive/transmit by setting the Stop Sequence Enable PEN bit. At the end of a receive/transmit, the SCL line is held low after the falling edge of the ninth clock. When the PEN bit is set, the master will assert the SDA line low. When the SDA line is sampled low, the Baud Rate Generator is reloaded and counts down to `0'. When the Baud Rate Generator times out, the SCL pin will be brought high and one TBRG (Baud Rate Generator rollover count) later, the SDA pin will be deasserted. When the SDA pin is sampled high while SCL is high, the PP bit is set. One TBRG later, the PEN bit is cleared and the SSPxIF bit is set. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 546 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-31. Stop Condition in Receive or Transmit Mode SCL = 1 for TBRG, followed by SDA = 1 for TBRG after SDA sampled high. P bit (SSPxSTAT<4>) is set. Write to SSPxCON2, set PEN PEN bit (SSPxCON2<2>) is cleared by hardware and the SSPxIF bit is set Falling edge of 9th clock TBRG SCL SDA Rev. 30-000041A 4/3/2017 ACK P TBRG TBRG TBRG SCL brought high after TBRG SDA asserted low before rising edge of clock to setup Stop condition Note: TBRG = one Baud Rate Generator period. 35.6.9.1 Write Collision on Stop the user writes the SSPxBUF when a Stop sequence is in progress, then the WCOL bit is set and the If contents of the buffer are unchanged (the write does not occur). 35.6.10 Sleep Operation While in Sleep mode, the I2C slave module can receive addresses or data and when an address match or complete byte transfer occurs, wake the processor from Sleep (if the MSSP interrupt is enabled). 35.6.11 Effects of a Reset A Reset disables the MSSP module and terminates the current transfer. 35.6.12 Multi-Master Mode In Multi-Master mode, the interrupt generation on the detection of the Start and Stop conditions allows the determination of when the bus is free. The Stop (P) and Start (S) bits are cleared from a Reset or when the MSSP module is disabled. Control of the I2C bus may be taken when the P bit is set, or the bus is Idle, with both the S and P bits clear. When the bus is busy, enabling the SSP interrupt will generate the interrupt when the Stop condition occurs. In multi-master operation, the SDA line must be monitored for arbitration to see if the signal level is the expected output level. This check is performed by hardware with the result placed in the BCLxIF bit. The states where arbitration can be lost are: * * * * * Address Transfer Data Transfer A Start Condition A Repeated Start Condition An Acknowledge Condition 35.6.13 Multi -Master Communication, Bus Collision and Bus Arbitration Multi-Master mode support is achieved by bus arbitration. When the master outputs address/data bits onto the SDA pin, arbitration takes place when the master outputs a `1' on SDA, by letting SDA float high and another master asserts a `0'. When the SCL pin floats high, data should be stable. If the expected data on SDA is a `1' and the data sampled on the SDA pin is `0', then a bus collision has taken place. The master will set the Bus Collision Interrupt Flag, BCLxIF and reset the I2C port to its Idle state (Figure 35-32). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 547 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module If a transmit was in progress when the bus collision occurred, the transmission is halted, the BF flag is cleared, the SDA and SCL lines are deasserted and the SSPxBUF can be written to. When the user services the bus collision Interrupt Service Routine and if the I2C bus is free, the user can resume communication by asserting a Start condition. If a Start, Repeated Start, Stop or Acknowledge condition was in progress when the bus collision occurred, the condition is aborted, the SDA and SCL lines are deasserted and the respective control bits in the SSPxCON2 register are cleared. When the user services the bus collision Interrupt Service Routine and if the I2C bus is free, the user can resume communication by asserting a Start condition. The master will continue to monitor the SDA and SCL pins. If a Stop condition occurs, the SSPxIF bit will be set. A write to the SSPxBUF will start the transmission of data at the first data bit, regardless of where the transmitter left off when the bus collision occurred. In Multi-Master mode, the interrupt generation on the detection of Start and Stop conditions allows the determination of when the bus is free. Control of the I2C bus can be taken when the P bit is set, or the bus is Idle and the S and P bits are cleared. Figure 35-32. Bus Collision Timing for Transmit and Acknowledge Rev. 30-000042A 4/3/2017 Data changes while SCL = 0 SDA line pulled low by another source SDA released by master Sample SDA. While SCL is high, data does not match what is driven by the master. Bus collision has occurred. SDA SCL Set bus collision interrupt (BCLxIF) BCLxIF 35.6.13.1 Bus Collision During a Start Condition During a Start condition, a bus collision occurs if: 1. 2. SDA or SCL are sampled low at the beginning of the Start condition (Figure 35-33). SCL is sampled low before SDA is asserted low (Figure 35-34). During a Start condition, both the SDA and the SCL pins are monitored. If the SDA pin is already low, or the SCL pin is already low, then all of the following occur: * * * the Start condition is aborted, the BCLxIF flag is set and the MSSP module is reset to its Idle state (Figure 35-33). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 548 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-33. Bus Collision During Start Condition (SDA Only) Rev. 30-000043A 4/3/2017 SDA goes low before the SEN bit is set. Set BCLxIF, S bit and SSPxIF set because SDA = 0, SCL = 1. SDA SCL Set SEN, enable Start condition if SDA = 1, SCL = 1 SEN cleared automatically because of bus collision. SSPx module reset into Idle state. SEN SDA sampled low before Start condition. Set BCLxIF. S bit and SSPxIF set because SDA = 0, SCL = 1. BCLxIF SSPxIF and BCLxIF are cleared by software S SSPxIF SSPxIF and BCLxIF are cleared by software The Start condition begins with the SDA and SCL pins deasserted. When the SDA pin is sampled high, the Baud Rate Generator is loaded and counts down. If the SCL pin is sampled low while SDA is high, a bus collision occurs because it is assumed that another master is attempting to drive a data `1' during the Start condition. Figure 35-34. Bus Collision During Start Condition (SCL = 0) Rev. 30-000044A 4/3/2017 SDA = 0, SCL = 1 TBRG TBRG SDA Set SEN, enable Start sequence if SDA = 1, SCL = 1 SCL SCL = 0 before SDA = 0, bus collision occurs. Set BCLxIF. SEN SCL = 0 before BRG time-out, bus collision occurs. Set BCLxIF. BCLxIF Interrupt cleared by software '0' '0' SSPxIF '0' '0' S (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 549 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module If the SDA pin is sampled low during this count, the BRG is reset and the SDA line is asserted early (Figure 35-35). If, however, a `1' is sampled on the SDA pin, the SDA pin is asserted low at the end of the BRG count. The Baud Rate Generator is then reloaded and counts down to zero; if the SCL pin is sampled as `0' during this time, a bus collision does not occur. At the end of the BRG count, the SCL pin is asserted low. Figure 35-35. BRG Reset Due to SDA Arbitration During Start Condition Rev. 30-000045A 4/10/2017 SDA = 0, SCL = 1 Set S Less than TBRG SDA Set SSPxIF TBRG SDA pulled low by other master. Reset BRG and assert SDA. SCL S SCL pulled low after BRG time out SEN BCLxIF Set SEN, enable Start sequence if SDA = 1, SCL = 1 '0' S SSPxIF SDA = 0, SCL = 1, set SSPxIF Interrupts cleared by software Important: The reason that bus collision is not a factor during a Start condition is that no two bus masters can assert a Start condition at the exact same time. Therefore, one master will always assert SDA before the other. This condition does not cause a bus collision because the two masters must be allowed to arbitrate the first address following the Start condition. If the address is the same, arbitration must be allowed to continue into the data portion, Repeated Start or Stop conditions. 35.6.13.2 Bus Collision During a Repeated Start Condition During a Repeated Start condition, a bus collision occurs if: 1. 2. A low level is sampled on SDA when SCL goes from low level to high level (Case 1). SCL goes low before SDA is asserted low, indicating that another master is attempting to transmit a data `1' (Case 2). When the user releases SDA and the pin is allowed to float high, the BRG is loaded with SSPxADD and counts down to zero. The SCL pin is then deasserted and when sampled high, the SDA pin is sampled. If SDA is low, a bus collision has occurred (i.e., another master is attempting to transmit a data `0', Figure 35-36). If SDA is sampled high, the BRG is reloaded and begins counting. If SDA goes from high-to-low before the BRG times out, no bus collision occurs because no two masters can assert SDA at exactly the same time. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 550 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Figure 35-36. Bus Collision During a Repeated Start Condition (Case 1) Rev. 30-000046A 4/3/2017 SDA SCL Sample SDA when SCL goes high. If SDA = 0, set BCLxIF and release SDA and SCL. RSEN BCLxIF Cleared by software S '0' SSPxIF '0' If SCL goes from high-to-low before the BRG times out and SDA has not already been asserted, a bus collision occurs. In this case, another master is attempting to transmit a data `1' during the Repeated Start condition, see Figure 35-37. If, at the end of the BRG time out, both SCL and SDA are still high, the SDA pin is driven low and the BRG is reloaded and begins counting. At the end of the count, regardless of the status of the SCL pin, the SCL pin is driven low and the Repeated Start condition is complete. Figure 35-37. Bus Collision During Repeated Start Condition (Case 2) Rev. 30-000047A 4/3/2017 TBRG TBRG SDA SCL BCLxIF SCL goes low before SDA, set BCLxIF. Release SDA and SCL. Interrupt cleared by software RSEN '0' S SSPxIF 35.6.13.3 Bus Collision During a Stop Condition Bus collision occurs during a Stop condition if: 1. 2. After the SDA pin has been deasserted and allowed to float high, SDA is sampled low after the BRG has timed out (Case 1). After the SCL pin is deasserted, SCL is sampled low before SDA goes high (Case 2). The Stop condition begins with SDA asserted low. When SDA is sampled low, the SCL pin is allowed to float. When the pin is sampled high (clock arbitration), the Baud Rate Generator is loaded with SSPxADD (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 551 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module and counts down to zero. After the BRG times out, SDA is sampled. If SDA is sampled low, a bus collision has occurred. This is due to another master attempting to drive a data `0' (Figure 35-38). If the SCL pin is sampled low before SDA is allowed to float high, a bus collision occurs. This is another case of another master attempting to drive a data `0' (Figure 35-39). Figure 35-38. Bus Collision During a Stop Condition (Case 1) Rev. 30-000048A 4/3/2017 TBRG TBRG TBRG SDA SDA sampled low after TBRG, set BCLxIF SDA asserted low SCL PEN BCLxIF P '0' SSPxIF '0' Figure 35-39. Bus Collision During a Stop Condition (Case 2) Rev. 30-000049A 4/3/2017 TBRG TBRG TBRG SDA Assert SDA SCL SCL goes low before SDA goes high, set BCLxIF PEN BCLxIF 35.7 P '0' SSPxIF '0' Baud Rate Generator The MSSP module has a Baud Rate Generator available for clock generation in both I2C and SPI Master modes. The Baud Rate Generator (BRG) reload value is placed in the SSPxADD register. When a write occurs to SSPxBUF, the Baud Rate Generator will automatically begin counting down. Once the given operation is complete, the internal clock will automatically stop counting and the clock pin will remain in its last state. An internal signal "Reload" shown in Figure 35-40 triggers the value from SSPxADD to be loaded into the BRG counter. This occurs twice for each oscillation of the module clock line. The logic dictating when the reload signal is asserted depends on the mode in which the MSSP is being operated. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 552 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Table 35-1 illustrates clock rates based on instruction cycles and the BRG value loaded into SSPxADD. MSSP Baud Rate Generator Frequency Equation = 4 x + 1 Figure 35-40. Baud Rate Generator Block Diagram Rev. 30-000050A 4/3/2017 SSPM<3:0> SSPM<3:0> Reload SCL Control SSPCLK SSPxADD<7:0> Reload BRG Down Counter F OSC/2 Important: Values of 0x00, 0x01 and 0x02 are not valid for SSPxADD when used as a Baud Rate Generator for I2C. This is an implementation limitation. Table 35-1. MSSP Clock Rate w/BRG FOSC FCY BRG Value Fclock (2 Rollovers of BRG) 32 MHz 8 MHz 13h 400 kHz 32 MHz 8 MHz 19h 308 kHz 32 MHz 8 MHz 4Fh 100 kHz 16 MHz 4 MHz 09h 400 kHz 16 MHz 4 MHz 0Ch 308 kHz 16 MHz 4 MHz 27h 100 kHz 4 MHz 1 MHz 09h 100 kHz Note: Refer to the I/O port electrical specifications in the "Electrical Specifications" section, Internal Oscillator Parameters, to ensure the system is designed to support Iol requirements. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 553 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.8 Register Summary: MSSP Control Offset Name Bit Pos. 0x018C SSP1BUF 7:0 0x018D SSP1ADD 7:0 0x018E SSP1MSK 7:0 0x018F SSP1STAT 7:0 SMP CKE D/A P 0x0190 SSP1CON1 7:0 WCOL SSPOV SSPEN CKP 0x0191 SSP1CON2 7:0 GCEN ACKSTAT ACKDT ACKEN RCEN 0x0192 SSP1CON3 7:0 ACKTIM PCIE SCIE BOEN SDAHT 35.9 BUF[7:0] ADD[7:0] MSK[6:0] MSK0 S R/W UA BF PEN RSEN SEN SBCDE AHEN DHEN SSPM[3:0] Register Definitions: MSSP Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 554 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.1 SSPxSTAT Name: Offset: SSPxSTAT 0x018F MSSP Status Register Bit Access Reset 7 6 5 4 3 2 1 0 SMP CKE D/A P S R/W UA BF R/W R/W RO RO RO RO RO RO 0 0 0 0 0 0 0 0 Bit 7 - SMP Slew Rate Control bit Value 1 0 0 1 0 Mode SPI Master SPI Master SPI Slave I2C I2C Description Input data is sampled at the end of data output time Input data is sampled at the middle of data output time Keep this bit cleared in SPI Slave mode Slew rate control is disabled for Standard Speed mode (100 kHz and 1 MHz) Slew rate control is enabled for High-Speed mode (400 kHz) Bit 6 - CKE SPI: Clock select bit(4) I2C: SMBus Select bit Value 1 0 1 0 Mode SPI SPI I2C I2C Description Transmit occurs on the transition from active to Idle clock state Transmit occurs on the transition from Idle to active clock state Enables SMBus-specific inputs Disables SMBus-specific inputs Bit 5 - D/A Data/Address bit Value x 1 0 Mode SPI or I2C Master I2C Slave I2C Slave Description Reserved Indicates that the last byte received or transmitted was data Indicates that the last byte received or transmitted was address Bit 4 - P Stop bit(1) Value x 1 0 Mode SPI I2C I2C Description Reserved Stop bit was detected last Stop bit was not detected last Bit 3 - S Start bit(1) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 555 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Value x 1 0 Mode SPI I2C I2C Description Reserved Start bit was detected last Start bit was not detected last Bit 2 - R/W Read/Write Information bit(2,3) Value x 1 0 1 0 Mode SPI I2C Slave I2C Slave I2C Master I2C Master Description Reserved Read Write Transmit is in progress Transmit is not in progress Bit 1 - UA Update Address bit (10-Bit Slave mode only) Value x 1 0 Mode Description All other modes Reserved I2C 10-bit Slave Indicates that the user needs to update the address in the SSPxADD register I2C 10-bit Slave Address does not need to be updated Bit 0 - BF Buffer Full Status bit(5) Value 1 0 1 0 Mode I2C Transmit I2C Transmit SPI and I2C Receive SPI and I2C Receive Description Character written to SSPxBUF has not been sent SSPxBUF is ready for next character Received character in SSPxBUF has not been read Received character in SSPxBUF has been read Note: 1. This bit is cleared on Reset and when SSPEN is cleared. 2. In I2C Slave mode this bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next Start bit, Stop bit or not ACK bit. 3. ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is in Active mode. 4. Polarity of clock state is set by the CKP bit. 5. I2C receive status does not include ACK and Stop bits. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 556 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.2 SSPxCON1 Name: Offset: SSPxCON1 0x0190 MSSP Control Register 1 Bit Access Reset 7 6 5 4 WCOL SSPOV SSPEN CKP 3 R/W/HS R/W/HS R/W R/W R/W 0 0 0 0 0 2 1 0 R/W R/W R/W 0 0 0 SSPM[3:0] Bit 7 - WCOL Write Collision Detect bit Value 1 Mode SPI 1 I2C Master transmit 1 I2C Slave transmit 0 SPI or I2C Master or Slave transmit Master or Slave receive x Description A write to the SSPxBUF register was attempted while the previous byte was still transmitting (must be cleared by software) A write to the SSPxBUF register was attempted while the I2C conditions were not valid for a transmission to be started (must be cleared by software) The SSPxBUF register is written while it is still transmitting the previous word (must be cleared in software) No collision Don't care Bit 6 - SSPOV Receive Overflow Indicator bit(1) Value 1 Mode SPI Slave 1 I2C Receive 0 SPI Slave or I2C Receive SPI Master or I2C Master transmit x Description A byte is received while the SSPxBUF register is still holding the previous byte. The user must read SSPxBUF, even if only transmitting data, to avoid setting overflow. (must be cleared in software) A byte is received while the SSPxBUF register is still holding the previous byte (must be cleared in software) No overflow Don't care Bit 5 - SSPEN Master Synchronous Serial Port Enable bit.(2) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 557 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Value 1 1 0 Mode Description SPI Enables the serial port. The SCKx, SDOx, SDIx, and SSx pin selections must be made with the PPS controls. Each signal must be configured with the corresponding TRIS control to the direction appropriate for the mode selected. I2C Enables the serial port. The SDAx and SCLx pin selections must be made with the PPS controls. Since both signals are bidirectional the PPS input pin and PPS output pin selections must be made that specify the same pin. Both pins must be configured as inputs with the corresponding TRIS controls. All Disables serial port and configures these pins as I/O port pins Bit 4 - CKP SCK Release Control bit Value 1 0 1 0 x Mode SPI SPI I2C Slave I2C Slave I2C Master Description Idle state for the clock is a high level Idle state for the clock is a low level Releases clock Holds clock low (clock stretch), used to ensure data setup time Unused in this mode Bits 3:0 - SSPM[3:0] Master Synchronous Serial Port Mode Select bits(4) Value 1111 1110 1101 1100 1011 1010 1001 1000 0111 0110 0101 0100 0011 0010 0001 0000 Description I2C Slave mode: 10-bit address with Start and Stop bit interrupts enabled I2C Slave mode: 7-bit address with Start and Stop bit interrupts enabled Reserved - do not use Reserved - do not use I2C Firmware Controlled Master mode (slave Idle) SPI Master mode: Clock = FOSC/(4*(SSPxADD+1)). SSPxADD must be greater than 0.(3) Reserved - do not use I2C Master mode: Clock = FOSC/(4 * (SSPxADD + 1)) I2C Slave mode: 10-bit address I2C Slave mode: 7-bit address SPI Slave mode: Clock = SCKx pin. SSx pin control is disabled SPI Slave mode: Clock = SCKx pin. SSx pin control is enabled SPI Master mode: Clock = TMR2 output/2 SPI Master mode: Clock = Fosc/64 SPI Master mode: Clock = Fosc/16 SPI Master mode: Clock = Fosc/4 Note: 1. In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPxBUF register. 2. When enabled, these pins must be properly configured as inputs or outputs. 3. SSPxADD = 0 is not supported. 4. Bit combinations not specifically listed here are either reserved or implemented in I2C mode only. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 558 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.3 SSPxCON2 Name: Offset: SSPxCON2 0x0191 Control Register for I2C Operation Only MSSP Control Register 2 Bit Access Reset 7 6 5 4 3 2 1 0 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN R/W R/W/HC R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bit 7 - GCEN General Call Enable bit (Slave mode only) Value x 1 0 Mode Master mode Slave mode Slave mode Description Don't care General call is enabled General call is not enabled Bit 6 - ACKSTAT Acknowledge Status bit (Master Transmit mode only) Value 1 0 Description Acknowledge was not received from slave Acknowledge was received from slave Bit 5 - ACKDT Acknowledge Data bit (Master Receive mode only)(1) Value 1 0 Description Not Acknowledge Acknowledge Bit 4 - ACKEN Acknowledge Sequence Enable bit(2) Value 1 0 Description Initiates Acknowledge sequence on SDAx and SCLx pins and transmits ACKDT data bit; automatically cleared by hardware Acknowledge sequence is Idle Bit 3 - RCEN Receive Enable bit (Master Receive mode only)(2) Value 1 0 Description Enables Receive mode for I2C Receive is Idle Bit 2 - PEN Stop Condition Enable bit (Master mode only)(2) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 559 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Value 1 0 Description Initiates Stop condition on SDAx and SCLx pins; automatically cleared by hardware Stop condition is Idle Bit 1 - RSEN Repeated Start Condition Enable bit (Master mode only)(2) Value 1 0 Description Initiates Repeated Start condition on SDAx and SCLx pins; automatically cleared by hardware Repeated Start condition is Idle Bit 0 - SEN Start Condition Enable bit (Master mode only)(2) Value 1 0 Description Initiates Start condition on SDAx and SCLx pins; automatically cleared by hardware Start condition is Idle Note: 1. The value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive. 2. If the I2C module is active, these bits may not be set (no spooling) and the SSPxBUF may not be written (or writes to the SSPxBUF are disabled). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 560 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.4 SSPxCON3 Name: Offset: SSPxCON3 0x0192 MSSP Control Register 3 Bit Access Reset 7 6 5 4 3 2 1 0 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN R/HS/HC R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bit 7 - ACKTIM Acknowledge Time Status bit Unused in Master mode. Value x 1 0 Mode SPI or I2C Master I2C Slave and AHEN = 1 or DHEN = 1 I2C Slave Description This bit is not used Eighth falling edge of SCL has occurred and the ACK/ NACK state is active ACK/NACK state is not active. Transitions low on ninth rising edge of SCL. Bit 6 - PCIE Stop Condition Interrupt Enable bit(1) Value x 1 0 Mode SPI or SSPM = 1111 or 0111 SSPM 1111 and SSPM 0111 SSPM 1111 and SSPM 0111 Description Don't care Enable interrupt on detection of Stop condition Stop detection interrupts are disabled Bit 5 - SCIE Start Condition Interrupt Enable bit Value x 1 0 Mode SPI or SSPM = 1111 or 0111 SSPM 1111 and SSPM 0111 SSPM 1111 and SSPM 0111 Description Don't care Enable interrupt on detection of Start condition Start detection interrupts are disabled Bit 4 - BOEN Buffer Overwrite Enable bit(2) Value 1 0 1 Mode SPI SPI I2C 0 I2C Description SSPxBUF is updated every time a new data byte is available, ignoring the BF bit If a new byte is receive with BF set then SSPOV is set and SSPxBUF is not updated SSPxBUF is updated every time a new data byte is available, ignoring the SSPOV effect on updating the buffer SSPxBUF is only updated when SSPOV is clear Bit 3 - SDAHT SDA Hold Time Selection bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 561 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module Value x 1 0 Mode SPI I2C I2C Description Not used in SPI mode Minimum of 300ns hold time on SDA after the falling edge of SCL Minimum of 100ns hold time on SDA after the falling edge of SCL Bit 2 - SBCDE Slave Mode Bus Collision Detect Enable bit Unused in Master mode. Value x 1 0 Mode SPI or I2C Master I2C Slave I2C Slave Description Don't care Collision detection is enabled Collision detection is not enabled Bit 1 - AHEN Address Hold Enable bit Value x 1 0 Mode Description 2 SPI or I C Master Don't care I2C Slave Address hold is enabled. As a result CKP is cleared after the eighth falling SCL edge of an address byte reception. Software must set the CKP bit to resume operation. I2C Slave Address hold is not enabled Bit 0 - DHEN Data Hold Enable bit Value x 1 0 Mode Description SPI or I2C Master Don't care I2C Slave Data hold is enabled. As a result CKP is cleared after the eighth falling SCL edge of a data byte reception. Software must set the CKP bit to resume operation. I2C Slave Data hold is not enabled Note: 1. This bit has no effect in Slave modes that Start and Stop condition detection is explicitly listed as enabled. 2. For daisy-chained SPI operation; allows the user to ignore all but the last received byte. SSPOV is still set when a new byte is received and BF = 1, but hardware continues to write the most recent byte to SSPxBUF. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 562 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.5 SSPxBUF Name: Offset: SSPxBUF 0x018C MSSP Data Buffer Register Bit 7 6 5 4 3 2 1 0 BUF[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W x x x x x x x x Bits 7:0 - BUF[7:0] MSSP Input and Output Data Buffer bits (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 563 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.6 SSPxADD Name: Offset: SSPxADD 0x018D MSSP Baud Rate Divider and Address Register Bit 7 6 5 4 3 2 1 0 ADD[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - ADD[7:0] * SPI and I2C Master: Baud rate divider * I2C Slave: Address bits Value 3 to 255 Mode SPI and I2C Master 2,4,6,8 I2C 10-bit Slave MS Address I2C 10-bit Slave LS Address I2C 7-bit Slave n 2*(1 to 127) (c) 2018 Microchip Technology Inc. Description Baud rate divider. SCK/SCL pin clock period = ((n + 1) *4)/FOSC. Values less than 3 are not valid. Bits 7-3 and Bit 0 are not used and are don't care. Bits 2:1 are bits 9:8 of the 10-bit Slave Most Significant Address Bits 7:0 of 10-Bit Slave Least Significant Address Bit 0 is not used and is don't care. Bits 7:1 are the 7-bit Slave Address Datasheet Preliminary DS40002000A-page 564 PIC16(L)F18424/44 (MSSP) Master Synchronous Serial Port Module 35.9.7 SSPxMSK Name: Offset: SSPxMSK 0x018E MSSP Address Mask Register Bit 7 6 5 4 3 2 1 MSK[6:0] Access Reset 0 MSK0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 7:1 - MSK[6:0] Mask bits Value 1 0 Mode Description I2C Slave The received address bit n is compared to SSPxADD bit n to detect I2C address match I2C Slave The received address bit n is not used to detect I2C address match Bit 0 - MSK0 Mask bit for I2C 10-bit Slave mode Value 1 0 x Mode Description I2C 10-bit Slave The received address bit 0 is compared to SSPxADD bit 0 to detect I2C address match 2 I C 10-bit Slave The received address bit 0 is not used to detect I2C address match SPI or I2C 7-bit Don't care (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 565 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36. (EUSART) Enhanced Universal Synchronous Asynchronous Receiver Transmitter The Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) module is a serial I/O communications peripheral. It contains all the clock generators, shift registers and data buffers necessary to perform an input or output serial data transfer independent of device program execution. The EUSART, also known as a Serial Communications Interface (SCI), can be configured as a full-duplex asynchronous system or half-duplex synchronous system. Full-Duplex mode is useful for communications with peripheral systems, such as CRT terminals and personal computers. Half-Duplex Synchronous mode is intended for communications with peripheral devices, such as A/D or D/A integrated circuits, serial EEPROMs or other microcontrollers. These devices typically do not have internal clocks for baud rate generation and require the external clock signal provided by a master synchronous device. The EUSART module includes the following capabilities: * * * * * * * * * * * Full-duplex asynchronous transmit and receive Two-character input buffer One-character output buffer Programmable 8-bit or 9-bit character length Address detection in 9-bit mode Input buffer overrun error detection Received character framing error detection Half-duplex synchronous master Half-duplex synchronous slave Programmable clock polarity in Synchronous modes Sleep operation The EUSART module implements the following additional features, making it ideally suited for use in Local Interconnect Network (LIN) bus systems: * * * Automatic detection and calibration of the baud rate Wake-up on Break reception 13-bit Break character transmit Block diagrams of the EUSART transmitter and receiver are shown in Figure 36-1 and Figure 36-2. The operation of the EUSART module consists of six registers: * * * * * * Transmit Status and Control (TXxSTA) Receive Status and Control (RCxSTA) Baud Rate Control (BAUDxCON) Baud Rate Value (SPxBRG) Receive Data Register (RCxREG) Transmit Data Register (TXxREG) The RXx/DTx and TXx/CKx input pins are selected with the RXxPPS and TXxPPS registers, respectively. TXx, CKx, and DTx output pins are selected with each pin's RxyPPS register. Since the RX input is coupled with the DT output in Synchronous mode, it is the user's responsibility to select the same pin for both of these functions when operating in Synchronous mode. The EUSART control logic will control the data direction drivers automatically. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 566 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Figure 36-1. EUSART Transmit Block Diagram Rev. 10-000 113C 2/15/201 7 Data bu s TXIE 8 Inte rrupt TXREG register SYNC CSRC TXIF 8 RxyPP S(1) TXEN CKx Pi n PPS 1 MSb LSb (8) 0 0 RXx/DTx Pin Pin Buffer and Control PPS Transmit Shift Register (TSR) CKPPS (2) TX_out Bau d Rate Gene rato r TRMT FOSC /n TX9 n BRG16 +1 SPB RG H SPB RG L Multiplier x4 x16 x64 SYNC 1 x 0 0 0 BRGH x 1 1 0 0 BRG16 x 1 0 1 0 TX9D 0 TXx/CKx Pi n PPS 1 RxyPP S(2) SYNC CSRC Not e 1: In S ynchro nous mod e, the DT output an d RX inpu t PPS selectio ns should en able th e same pin. 2: In Master S yn chr onous mo de the TX output an d CK inpu t PPS selections shou ld e nable the sa me pin. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 567 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Figure 36-2. EUSART Receive Block Diagram Rev. 10-000 114B 2/15/201 7 CRE N OERR RXPPS (1) RSR Register MSb RXx/DTx pin Pin Buffer and Control PPS RCIDL SPE N Data Recove ry Stop (8) 7 LSb 1 0 Start SYNC CSRC PPS RX9 1 CKx Pi n 0 CKPPS (2) Bau d Rate Gene rato r FOSC /n FERR RX9D RCREG Register FIFO 8 BRG16 +1 SPB RG H SPB RG L Multiplier x4 x16 x64 SYNC 1 x 0 0 0 BRGH x 1 1 0 0 BRG16 x 1 0 1 0 n Data B us RCxIF RCxIE Inte rrupt Not e 1: In S ynchro nous mod e, the DT output an d RX inpu t PPS selectio ns should en able th e same pin. 2: In Master S yn chr onous mo de the TX output an d CK inpu t PPS selections shou ld e nable the sa me pin. 36.1 EUSART Asynchronous Mode The EUSART transmits and receives data using the standard non-return-to-zero (NRZ) format. NRZ is implemented with two levels: a VOH Mark state which represents a `1' data bit, and a VOL Space state which represents a `0' data bit. NRZ refers to the fact that consecutively transmitted data bits of the same value stay at the output level of that bit without returning to a neutral level between each bit transmission. An NRZ transmission port idles in the Mark state. Each character transmission consists of one Start bit followed by eight or nine data bits and is always terminated by one or more Stop bits. The Start bit is always a space and the Stop bits are always marks. The most common data format is eight bits. Each transmitted bit persists for a period of 1/(Baud Rate). An on-chip dedicated 8-bit/16-bit Baud Rate Generator is used to derive standard baud rate frequencies from the system oscillator. See Table 36-2 for examples of baud rate configurations. The EUSART transmits and receives the LSb first. The EUSART's transmitter and receiver are functionally independent, but share the same data format and baud rate. Parity is not supported by the hardware, but can be implemented in software and stored as the ninth data bit. 36.1.1 EUSART Asynchronous Transmitter The Figure 36-1 is a simplified representation of the transmitter. The heart of the transmitter is the serial Transmit Shift Register (TSR), which is not directly accessible by software. The TSR obtains its data from the transmit buffer, which is the TXxREG register. 36.1.1.1 Enabling the Transmitter The EUSART transmitter is enabled for asynchronous operations by configuring the following three control bits: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 568 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... * TXEN = 1 (enables the transmitter circuitry of the EUSART) * SYNC = 0 (configures the EUSART for asynchronous operation) * SPEN = 1 (enables the EUSART and automatically enables the output drivers for the RxyPPS selected as the TXx/CKx output) All other EUSART control bits are assumed to be in their default state. If the TXx/CKx pin is shared with an analog peripheral, the analog I/O function must be disabled by clearing the corresponding ANSEL bit. Important: The TXxIF Transmitter Interrupt flag is set when the TXEN enable bit is set and the TSR is idle. 36.1.1.2 Transmitting Data A transmission is initiated by writing a character to the TXxREG register. If this is the first character, or the previous character has been completely flushed from the TSR, the data in the TXxREG is immediately transferred to the TSR register. If the TSR still contains all or part of a previous character, the new character data is held in the TXxREG until the Stop bit of the previous character has been transmitted. The pending character in the TXxREG is then transferred to the TSR in one TCY immediately following the Stop bit transmission. The transmission of the Start bit, data bits and Stop bit sequence commences immediately following the transfer of the data to the TSR from the TXxREG. 36.1.1.3 Transmit Data Polarity The polarity of the transmit data can be controlled with the SCKP bit of the BAUDxCON register. The default state of this bit is `0' which selects high true transmit idle and data bits. Setting the SCKP bit to `1' will invert the transmit data resulting in low true idle and data bits. The SCKP bit controls transmit data polarity in Asynchronous mode only. In Synchronous mode, the SCKP bit has a different function. See the Clock Polarity section for more detail. 36.1.1.4 Transmit Interrupt Flag The TXxIF interrupt flag bit of the PIRx register is set whenever the EUSART transmitter is enabled and no character is being held for transmission in the TXxREG. In other words, the TXxIF bit is only clear when the TSR is busy with a character and a new character has been queued for transmission in the TXxREG. The TXxIF flag bit is not cleared immediately upon writing TXxREG. TXxIF becomes valid in the second instruction cycle following the write execution. Polling TXxIF immediately following the TXxREG write will return invalid results. The TXxIF bit is read-only, it cannot be set or cleared by software. The TXxIF interrupt can be enabled by setting the TXxIE interrupt enable bit of the PIEx register. However, the TXxIF flag bit will be set whenever the TXxREG is empty, regardless of the state of TXxIE enable bit. To use interrupts when transmitting data, set the TXxIE bit only when there is more data to send. Clear the TXxIE interrupt enable bit upon writing the last character of the transmission to the TXxREG. 36.1.1.5 TSR Status The TRMT bit of the TXxSTA register indicates the status of the TSR register. This is a read-only bit. The TRMT bit is set when the TSR register is empty and is cleared when a character is transferred to the TSR register from the TXxREG. The TRMT bit remains clear until all bits have been shifted out of the TSR register. No interrupt logic is tied to this bit, so the user needs to poll this bit to determine the TSR status. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 569 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Important: The TSR register is not mapped in data memory, so it is not available to the user. 36.1.1.6 Transmitting 9-Bit Characters The EUSART supports 9-bit character transmissions. When the TX9 bit of the TXxSTA register is set, the EUSART will shift nine bits out for each character transmitted. The TX9D bit of the TXxSTA register is the ninth, and Most Significant data bit. When transmitting 9-bit data, the TX9D data bit must be written before writing the eight Least Significant bits into the TXxREG. All nine bits of data will be transferred to the TSR shift register immediately after the TXxREG is written. A special 9-bit Address mode is available for use with multiple receivers. See the Address Detection section for more information on the Address mode. 36.1.1.7 Asynchronous Transmission Setup 1. Initialize the SPxBRGH, SPxBRGL register pair and the BRGH and BRG16 bits to achieve the desired baud rate (see EUSART Baud Rate Generator (BRG)). 2. Select the transmit output pin by writing the appropriate value to the RxyPPS register. 3. Enable the asynchronous serial port by clearing the SYNC bit and setting the SPEN bit. 4. If 9-bit transmission is desired, set the TX9 control bit. A set ninth data bit will indicate that the eight Least Significant data bits are an address when the receiver is set for address detection. 5. Set SCKP bit if inverted transmit is desired. 6. Enable the transmission by setting the TXEN control bit. This will cause the TXxIF interrupt bit to be set. 7. If interrupts are desired, set the TXxIE interrupt enable bit of the PIEx register 8. An interrupt will occur immediately provided that the GIE and PEIE bits of the INTCON register are also set. 9. If 9-bit transmission is selected, the ninth bit should be loaded into the TX9D data bit. 10. Load 8-bit data into the TXxREG register. This will start the transmission. Figure 36-3. Asynchronous Transmission Rev. 10-000 115A 2/7/201 7 Word 1 Write to TXxREG BRG Output (Shift Clock) TXx/CKx pin TXxIF bit (Transmit Buffer Reg Empty Flag) TRMT bit (Transmit Shift Reg Empty Flag) Start bit bit 0 bit 1 bit 7/8 Stop bit Word 1 1 TCY (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 570 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Figure 36-4. Asynchronous Transmission (Back-to-Back) Word 1 Rev. 10-000 116A 2/7/201 7 Word 2 Write to TXxREG BRG Output (Shift Clock) TXx/CKx pin TXxIF bit (Transmit Buffer Reg Empty Flag) TRMT bit (Transmit Shift Reg Empty Flag) 36.1.2 Start bit bit 0 bit 1 bit 7/8 Word 1 Stop bit Start bit bit 0 Word 2 1 TCY EUSART Asynchronous Receiver The Asynchronous mode is typically used in RS-232 systems. A simplified representation of the receiver is shown in the Figure 36-2. The data is received on the RXx/DTx pin and drives the data recovery block. The data recovery block is actually a high-speed shifter operating at 16 times the baud rate, whereas the serial Receive Shift Register (RSR) operates at the bit rate. When all eight or nine bits of the character have been shifted in, they are immediately transferred to a two character First-In-First-Out (FIFO) memory. The FIFO buffering allows reception of two complete characters and the start of a third character before software must start servicing the EUSART receiver. The FIFO and RSR registers are not directly accessible by software. Access to the received data is via the RCxREG register. 36.1.2.1 Enabling the Receiver The EUSART receiver is enabled for asynchronous operation by configuring the following three control bits: * CREN = 1 (enables the receiver circuitry of the EUSART) * SYNC = 0 (configures the EUSART for asynchronous operation) * SPEN = 1 (enables the EUSART) All other EUSART control bits are assumed to be in their default state. The user must set the RXxPPS register to select the RXx/DTx I/O pin and set the corresponding TRIS bit to configure the pin as an input. Important: If the RX/DT function is on an analog pin, the corresponding ANSEL bit must be cleared for the receiver to function. 36.1.2.2 Receiving Data The receiver data recovery circuit initiates character reception on the falling edge of the first bit. The first bit, also known as the Start bit, is always a zero. The data recovery circuit counts one-half bit time to the center of the Start bit and verifies that the bit is still a zero. If it is not a zero then the data recovery circuit aborts character reception, without generating an error, and resumes looking for the falling edge of the Start bit. If the Start bit zero verification succeeds then the data recovery circuit counts a full bit time to the center of the next bit. The bit is then sampled by a majority detect circuit and the resulting `0' or `1' is shifted into the RSR. This repeats until all data bits have been sampled and shifted into the RSR. One final bit time is measured and the level sampled. This is the Stop bit, which is always a `1'. If the data (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 571 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... recovery circuit samples a `0' in the Stop bit position then a framing error is set for this character, otherwise the framing error is cleared for this character. See the Receive Framing Error section for more information on framing errors. Immediately after all data bits and the Stop bit have been received, the character in the RSR is transferred to the EUSART receive FIFO and the RCxIF interrupt flag bit of the PIRx register is set. The top character in the FIFO is transferred out of the FIFO by reading the RCxREG register. Important: If the receive FIFO is overrun, no additional characters will be received until the overrun condition is cleared. See the Receive Overrun Error section for more information. 36.1.2.3 Receive Interrupts The RCxIF interrupt flag bit of the PIRx register is set whenever the EUSART receiver is enabled and there is an unread character in the receive FIFO. The RCxIF interrupt flag bit is read-only, it cannot be set or cleared by software. RCxIF interrupts are enabled by setting all of the following bits: * * * RCxIE, Interrupt Enable bit of the PIEx register PEIE, Peripheral Interrupt Enable bit of the INTCON register GIE, Global Interrupt Enable bit of the INTCON register The RCxIF interrupt flag bit will be set when there is an unread character in the FIFO, regardless of the state of interrupt enable bits. 36.1.2.4 Receive Framing Error Each character in the receive FIFO buffer has a corresponding framing error Status bit. A framing error indicates that a Stop bit was not seen at the expected time. The framing error status is accessed via the FERR bit of the RCxSTA register. The FERR bit represents the status of the top unread character in the receive FIFO. Therefore, the FERR bit must be read before reading the RCxREG. The FERR bit is read-only and only applies to the top unread character in the receive FIFO. A framing error (FERR = 1) does not preclude reception of additional characters. It is not necessary to clear the FERR bit. Reading the next character from the FIFO buffer will advance the FIFO to the next character and the next corresponding framing error. The FERR bit can be forced clear by clearing the SPEN bit of the RCxSTA register which resets the EUSART. Clearing the CREN bit of the RCxSTA register does not affect the FERR bit. A framing error by itself does not generate an interrupt. Important: If all receive characters in the receive FIFO have framing errors, repeated reads of the RCxREG will not clear the FERR bit. 36.1.2.5 Receive Overrun Error The receive FIFO buffer can hold two characters. An overrun error will be generated if a third character, in its entirety, is received before the FIFO is accessed. When this happens the OERR bit of the RCxSTA register is set. The characters already in the FIFO buffer can be read but no additional characters will be received until the error is cleared. The error must be cleared by either clearing the CREN bit of the RCxSTA register or by resetting the EUSART by clearing the SPEN bit of the RCxSTA register. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 572 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.1.2.6 Receiving 9-Bit Characters The EUSART supports 9-bit character reception. When the RX9 bit of the RCxSTA register is set the EUSART will shift nine bits into the RSR for each character received. The RX9D bit of the RCxSTA register is the ninth and Most Significant data bit of the top unread character in the receive FIFO. When reading 9-bit data from the receive FIFO buffer, the RX9D data bit must be read before reading the eight Least Significant bits from the RCxREG. 36.1.2.7 Address Detection A special Address Detection mode is available for use when multiple receivers share the same transmission line, such as in RS-485 systems. Address detection is enabled by setting the ADDEN bit of the RCxSTA register. Address detection requires 9-bit character reception. When address detection is enabled, only characters with the ninth data bit set will be transferred to the receive FIFO buffer, thereby setting the RCxIF interrupt bit. All other characters will be ignored. Upon receiving an address character, user software determines if the address matches its own. Upon address match, user software must disable address detection by clearing the ADDEN bit before the next Stop bit occurs. When user software detects the end of the message, determined by the message protocol used, software places the receiver back into the Address Detection mode by setting the ADDEN bit. 36.1.2.8 Asynchronous Reception Setup 1. Initialize the SPxBRGH:SPxBRGL register pair and the BRGH and BRG16 bits to achieve the desired baud rate (see the EUSART Baud Rate Generator (BRG) section). 2. Set the RXxPPS register to select the RXx/DTx input pin. 3. Clear the ANSEL bit for the RXx pin (if applicable). 4. Enable the serial port by setting the SPEN bit. The SYNC bit must be clear for asynchronous operation. 5. If interrupts are desired, set the RCxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. 6. If 9-bit reception is desired, set the RX9 bit. 7. Enable reception by setting the CREN bit. 8. The RCxIF interrupt flag bit will be set when a character is transferred from the RSR to the receive buffer. An interrupt will be generated if the RCxIE interrupt enable bit was also set. 9. Read the RCxSTA register to get the error flags and, if 9-bit data reception is enabled, the ninth data bit. 10. Get the received eight Least Significant data bits from the receive buffer by reading the RCxREG register. 11. If an overrun occurred, clear the OERR flag by clearing the CREN receiver enable bit. 36.1.2.9 9-Bit Address Detection Mode Setup This mode would typically be used in RS-485 systems. To set up an Asynchronous Reception with Address Detect Enable follow these steps: 1. 2. 3. 4. Initialize the SPxBRGH:SPxBRGL register pair and the BRGH and BRG16 bits to achieve the desired baud rate (see the EUSART Baud Rate Generator (BRG) section). Set the RXxPPS register to select the RXx input pin. Clear the ANSEL bit for the RXx pin (if applicable). Enable the serial port by setting the SPEN bit. The SYNC bit must be clear for asynchronous operation. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 573 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 5. 6. 7. 8. 9. 10. 11. 12. 13. If interrupts are desired, set the RCxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. Enable 9-bit reception by setting the RX9 bit. Enable address detection by setting the ADDEN bit. Enable reception by setting the CREN bit. The RCxIF interrupt flag bit will be set when a character with the ninth bit set is transferred from the RSR to the receive buffer. An interrupt will be generated if the RCxIE interrupt enable bit is also set. Read the RCxSTA register to get the error flags. The ninth data bit will always be set. Get the received eight Least Significant data bits from the receive buffer by reading the RCxREG register. Software determines if this is the device's address. If an overrun occurred, clear the OERR flag by clearing the CREN receiver enable bit. If the device has been addressed, clear the ADDEN bit to allow all received data into the receive buffer and generate interrupts. Figure 36-5. Asynchronous Reception Rev. 10-000 117A 2/8/201 7 RXx/DTx pin Start bit bit 0 Rcv Shift Reg Rcv Buffer Reg Word 1 bit 7/8 Stop bit Start bit bit 0 Word 2 bit 7/8 Stop bit Word 1 RCxREG Start bit bit 0 Word 3 bit 7/8 Stop bit Word 2 RCxREG RCIDL Read RCxREG RCxIF (Interrupt flag) OERR Flag CREN (software clear) Note: This timing diagram shows three bytes appearing on the RXx input. The OERR flag is set because the RCxREG is not read before the third word is received. 36.1.3 Clock Accuracy with Asynchronous Operation The factory calibrates the internal oscillator block output (INTOSC). However, the INTOSC frequency may drift as VDD or temperature changes, and this directly affects the asynchronous baud rate. Two methods may be used to adjust the baud rate clock, but both require a reference clock source of some kind. The first (preferred) method uses the OSCTUNE register to adjust the INTOSC output. Adjusting the value in the OSCTUNE register allows for fine resolution changes to the system clock source. The other method adjusts the value in the Baud Rate Generator. This can be done automatically with the Auto-Baud Detect feature (see Auto-Baud Detect). There may not be fine enough resolution when adjusting the Baud Rate Generator to compensate for a gradual change in the peripheral clock frequency. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 574 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.2 EUSART Baud Rate Generator (BRG) The Baud Rate Generator (BRG) is an 8-bit or 16-bit timer that is dedicated to the support of both the asynchronous and synchronous EUSART operation. By default, the BRG operates in 8-bit mode. Setting the BRG16 bit of the BAUDxCON register selects 16-bit mode. The SPxBRGH, SPxBRGL register pair determines the period of the free running baud rate timer. In Asynchronous mode the multiplier of the baud rate period is determined by both the BRGH bit of the TXxSTA register and the BRG16 bit of the BAUDxCON register. In Synchronous mode, the BRGH bit is ignored. Table 36-1 contains the formulas for determining the baud rate. Equation 36-1 provides a sample calculation for determining the baud rate and baud rate error. Typical baud rates and error values for various asynchronous modes have been computed and are shown in Table 36-2. It may be advantageous to use the high baud rate (BRGH = 1), or the 16-bit BRG (BRG16 = 1) to reduce the baud rate error. The 16-bit BRG mode is used to achieve slow baud rates for fast oscillator frequencies. The BRGH bit is used to achieve very high baud rates. Writing a new value to the SPxBRGH, SPxBRGL register pair causes the BRG timer to be reset (or cleared). This ensures that the BRG does not wait for a timer overflow before outputting the new baud rate. If the system clock is changed during an active receive operation, a receive error or data loss may result. To avoid this problem, check the status of the RCIDL bit to make sure that the receive operation is idle before changing the system clock. Equation 36-1. Calculating Baud Rate Error For a device with Fosc of 16 MHz, desired baud rate of 9600, Asynchronous mode, 8-bit BRG: = Solving for SPxBRG: = = 64 x + 1 -1 64 x 16000000 -1 64 x 9600 = 25.042 25 = 16000000 64 x 25 + 1 = 9615 = = - 9615 - 9600 9600 = 0.16 % (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 575 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Table 36-1. Baud Rate Formulas Configuration Bits BRG/EUSART Mode Baud Rate Formula 0 8-bit/Asynchronous FOSC/[64 (n+1)] 0 1 8-bit/Asynchronous 0 1 0 16-bit/Asynchronous 0 1 1 16-bit/Asynchronous 1 0 x 8-bit/Synchronous 1 1 x 16-bit/Synchronous SYNC BRG16 BRGH 0 0 0 FOSC/[16 (n+1)] FOSC/[4 (n+1)] Note: x = Don't care, n = value of SPxBRGH:SPxBRGL register pair. Table 36-2. Sample Baud Rates for Asynchronous Modes SYNC = 0, BRGH = 0, BRG16 = 0 FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz BAUD RATE Actual % SPBRG Actual % SPBRG Actual % SPBRG Actual % SPBRG Rate Error value Rate Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) (decimal) 300 -- -- -- -- -- -- -- -- -- -- -- -- 1200 -- -- -- 1221 1.73 255 1200 0.00 239 1200 0.00 143 2400 2404 0.16 207 2404 0.16 129 2400 0.00 119 2400 0.00 71 9600 9615 0.16 51 9470 -1.36 32 9600 0.00 29 9600 0.00 17 10417 10417 0.00 47 10417 0.00 29 10286 -1.26 27 10165 -2.42 16 19.2k 19.23k 0.16 25 19.53k 1.73 15 19.20k 0.00 14 19.20k 0.00 8 57.6k 55.55k -3.55 3 -- -- -- 57.60k 0.00 7 57.60k 0.00 2 115.2k -- -- -- -- -- -- -- -- -- -- -- -- SYNC = 0, BRGH = 0, BRG16 = 0 Fosc = 8.000 MHz Fosc = 4.000 MHz Fosc = 3.6864 MHz Fosc = 1.000 MHz BAUD RATE Actual % SPBRG Actual % SPBRG Actual % SPBRG Actual % SPBRG Rate Error value Rate Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) (decimal) 300 -- -- -- 300 0.16 207 300 0.00 191 300 0.16 51 1200 1202 0.16 103 1202 0.16 51 1200 0.00 47 1202 0.16 12 2400 2404 0.16 51 2404 0.16 25 2400 0.00 23 -- -- -- 9600 9615 0.16 12 -- -- -- 9600 0.00 5 -- -- -- (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 576 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 10417 10417 0.00 11 10417 0.00 5 19.2k -- -- -- -- -- -- 57.6k -- -- -- -- -- -- 115.2k -- -- -- -- -- -- -- -- -- -- -- -- 19.20k 0.00 2 -- -- -- 57.60k 0.00 0 -- -- -- -- -- -- -- -- -- SYNC = 0, BRGH = 1, BRG16 = 0 BAUD RATE Fosc = 32.000 MHz Actual Rate Fosc = 20.000 MHz % SPBRG Error value (decimal) Actual Rate Fosc = 18.432 MHz Fosc = 11.0592 MHz % SPBRG Actual % SPBRG Actual % SPBRG Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) 300 -- -- -- -- -- -- -- -- -- -- -- -- 1200 -- -- -- -- -- -- -- -- -- -- -- -- 2400 -- -- -- -- -- -- -- -- -- -- -- -- 9600 9615 0.16 207 9615 0.16 129 9600 0.00 119 9600 0.00 71 10417 10417 0.00 191 10417 0.00 119 10378 -0.37 110 10473 0.53 65 19.2k 19.23k 0.16 103 19.23k 0.16 64 19.20k 0.00 59 19.20k 0.00 35 57.6k 57.14k -0.79 34 56.82k -1.36 21 57.60k 0.00 19 57.60k 0.00 11 115.2k 117.64k 2.12 16 113.64k -1.36 10 115.2k 0.00 9 115.2k 0.00 5 SYNC = 0, BRGH = 1, BRG16 = 0 Fosc = 8.000 MHz Fosc = 4.000 MHz Fosc = 3.6864 MHz Fosc = 1.000 MHz BAUD RATE Actual % SPBRG Actual % SPBRG Actual % SPBRG Actual % SPBRG Rate Error value Rate Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) (decimal) 300 -- -- -- -- -- -- -- -- -- 300 0.16 207 1200 -- -- -- 1202 0.16 207 1200 0.00 191 1202 0.16 51 2400 2404 0.16 207 2404 0.16 103 2400 0.00 95 2404 0.16 25 9600 9615 0.16 51 9615 0.16 25 9600 0.00 23 -- -- -- 10417 10417 0.00 47 10417 0.00 23 10473 0.53 21 19.2k 19231 0.16 25 19.23k 0.16 12 19.2k 0.00 11 -- -- -- 57.6k 55556 -3.55 8 -- -- -- 57.60k 0.00 3 -- -- -- 115.2k -- -- -- -- 115.2k 0.00 1 -- -- -- BAUD RATE -- -- 10417 0.00 5 SYNC = 0, BRGH = 0, BRG16 = 1 Fosc = 32.000 MHz (c) 2018 Microchip Technology Inc. Fosc = 20.000 MHz Fosc = 18.432 MHz Datasheet Preliminary Fosc = 11.0592 MHz DS40002000A-page 577 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Actual % SPBRG Rate Error value (decimal) Actual Rate % SPBRG Actual % SPBRG Actual % SPBRG Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) 300 300.0 0.00 6666 300.0 -0.01 4166 300.0 0.00 3839 300.0 0.00 2303 1200 1200 -0.02 3332 1200 -0.03 1041 1200 0.00 959 1200 0.00 575 2400 2401 -0.04 832 2399 -0.03 520 2400 0.00 479 2400 0.00 287 9600 9615 0.16 207 9615 0.16 129 9600 0.00 119 9600 0.00 71 10417 10417 0.00 191 10417 0.00 119 10378 -0.37 110 10473 0.53 65 19.2k 19.23k 0.16 103 19.23k 0.16 64 19.20k 0.00 59 19.20k 0.00 35 57.6k 57.14k -0.79 34 56.818 -1.36 21 57.60k 0.00 19 57.60k 0.00 11 115.2k 117.6k 2.12 16 113.636 -1.36 10 115.2k 0.00 9 115.2k 0.00 5 SYNC = 0, BRGH = 0, BRG16 = 1 Fosc = 8.000 MHz Fosc = 4.000 MHz Fosc = 3.6864 MHz Fosc = 1.000 MHz BAUD RATE Actual % SPBRG Actual % SPBRG Actual % SPBRG Actual % SPBRG Rate Error value Rate Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) (decimal) 300 299.9 -0.02 1666 300.1 0.04 832 300.0 0.00 767 300.5 0.16 207 1200 1199 -0.08 416 1202 0.16 207 1200 0.00 191 1202 0.16 51 2400 2404 0.16 207 2404 0.16 103 2400 0.00 95 2404 0.16 25 9600 9615 0.16 51 9615 0.16 25 9600 0.00 23 -- -- -- 10417 10417 0.00 47 10417 0.00 23 10473 0.53 21 19.2k 19.23k 0.16 25 19.23k 0.16 12 19.20k 0.00 11 -- -- -- 57.6k 8 -- -- -- 57.60k 0.00 3 -- -- -- -- -- -- -- 115.2k 0.00 1 -- -- -- 115.2k 55556 -3.55 -- -- 10417 0.00 5 SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 Fosc = 32.000 MHz Fosc = 20.000 MHz Fosc = 18.432 MHz Fosc = 11.0592 MHz BAUD RATE Actual % SPBRG Actual % SPBRG Actual % SPBRG Actual % SPBRG Rate Error value Rate Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) (decimal) 300 300.0 0.00 26666 300.0 0.00 16665 300.0 0.00 15359 300.0 0.00 9215 1200 1200 0.00 6666 1200 -0.01 4166 1200 0.00 3839 1200 0.00 2303 2400 2400 0.01 3332 2400 0.02 2082 2400 0.00 1919 2400 0.00 1151 9600 9604 0.04 832 9597 -0.03 520 9600 0.00 479 9600 0.00 287 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 578 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 10417 10417 0.00 767 10417 0.00 479 10425 0.08 441 10433 0.16 264 19.2k 19.18k -0.08 416 19.23k 0.16 259 19.20k 0.00 239 19.20k 0.00 143 57.6k 57.55k -0.08 138 57.47k -0.22 86 57.60k 0.00 79 57.60k 0.00 47 115.2k 115.9k 0.64 68 116.3k 0.94 42 115.2k 0.00 39 115.2k 0.00 23 SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 Fosc = 8.000 MHz Fosc = 4.000 MHz Fosc = 3.6864 MHz Fosc = 1.000 MHz BAUD RATE Actual % SPBRG Actual % SPBRG Actual % SPBRG Actual % SPBRG Rate Error value Rate Error value Rate Error value Rate Error value (decimal) (decimal) (decimal) (decimal) 300 300.0 0.00 6666 300.0 0.01 3332 300.0 0.00 3071 300.1 0.04 832 1200 1200 -0.02 1666 1200 0.04 832 1200 0.00 767 1202 0.16 207 2400 2401 0.04 832 2398 0.08 416 2400 0.00 383 2404 0.16 103 9600 9615 0.16 207 9615 0.16 103 9600 0.00 95 9615 0.16 25 0 191 10417 0.00 95 10473 0.53 87 10417 0.00 23 19.2k 19.23k 0.16 103 19.23k 0.16 51 19.20k 0.00 47 19.23k 0.16 12 57.6k 57.14k -0.79 34 58.82k 2.12 16 57.60k 0.00 15 -- -- -- 115.2k 117.6k 2.12 16 111.1k -3.55 8 115.2k 0.00 7 -- -- -- 10417 10417 36.2.1 Auto-Baud Detect The EUSART module supports automatic detection and calibration of the baud rate. In the Auto-Baud Detect (ABD) mode, the clock to the BRG is reversed. Rather than the BRG clocking the incoming RX signal, the RX signal is timing the BRG. The Baud Rate Generator is used to time the period of a received 55h (ASCII "U") which is the Sync character for the LIN bus. The unique feature of this character is that it has five rising edges including the Stop bit edge. Setting the ABDEN bit of the BAUDxCON register starts the auto-baud calibration sequence. While the ABD sequence takes place, the EUSART state machine is held in Idle. On the first rising edge of the receive line, after the Start bit, the SPxBRG begins counting up using the BRG counter clock as shown in Figure 36-7. The fifth rising edge will occur on the RXx pin at the end of the eighth bit period. At that time, an accumulated value totaling the proper BRG period is left in the SPxBRGH, SPxBRGL register pair, the ABDEN bit is automatically cleared and the RCxIF interrupt flag is set. The value in the RCxREG needs to be read to clear the RCxIF interrupt. RCxREG content should be discarded. When calibrating for modes that do not use the SPxBRGH register the user can verify that the SPxBRGL register did not overflow by checking for 00h in the SPxBRGH register. The BRG auto-baud clock is determined by the BRG16 and BRGH bits as shown in Table 36-3. During ABD, both the SPxBRGH and SPxBRGL registers are used as a 16-bit counter, independent of the BRG16 bit setting. While calibrating the baud rate period, the SPxBRGH and SPxBRGL registers are clocked at 1/8th the BRG base clock rate. The resulting byte measurement is the average bit time when clocked at full speed. Note: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 579 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 1. 2. 3. If the WUE bit is set with the ABDEN bit, auto-baud detection will occur on the byte following the Break character (see Auto-Wake-up on Break). It is up to the user to determine that the incoming character baud rate is within the range of the selected BRG clock source. Some combinations of oscillator frequency and EUSART baud rates are not possible. During the auto-baud process, the auto-baud counter starts counting at one. Upon completion of the auto-baud sequence, to achieve maximum accuracy, subtract 1 from the SPxBRGH:SPxBRGL register pair. Table 36-3. BRG Counter Clock Rates BRG16 BRGH BRG Base Clock BRG ABD Clock 1 1 FOSC/4 FOSC/32 1 0 FOSC/16 FOSC/128 0 1 FOSC/16 FOSC/128 0 0 FOSC/64 FOSC/512 Note: During the ABD sequence, SPxBRGL and SPxBRGH registers are both used as a 16-bit counter, independent of the BRG16 setting. Figure 36-7. Automatic Baud Rate Calibration Rev. 10-000 120A 2/13/201 7 BRG Value XXXXh 0000h 001Ch Edge #1 RXx/DTx pin Edge #2 Edge #3 Edge #4 Edge #5 start bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 BRG Clock ABDEN Auto cleared Set by user RCxIF bit (Interrupt Flag) Read RCxREG SPxBRGH:L 36.2.2 XXXXh 001Ch Auto-Baud Overflow During the course of automatic baud detection, the ABDOVF bit of the BAUDxCON register will be set if the baud rate counter overflows before the fifth rising edge is detected on the RXx pin. The ABDOVF bit indicates that the counter has exceeded the maximum count that can fit in the 16 bits of the SPxBRGH:SPxBRGL register pair. After the ABDOVF bit has been set, the counter continues to count until the fifth rising edge is detected on the RXx pin. Upon detecting the fifth RX edge, the hardware will set the RCxIF interrupt flag and clear the ABDEN bit of the BAUDxCON register. The RCxIF flag can be subsequently cleared by reading the RCxREG register. The ABDOVF flag of the BAUDxCON register can be cleared by software directly. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 580 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... To terminate the auto-baud process before the RCxIF flag is set, clear the ABDEN bit then clear the ABDOVF bit of the BAUDxCON register. The ABDOVF bit will remain set if the ABDEN bit is not cleared first. 36.2.3 Auto-Wake-up on Break During Sleep mode, all clocks to the EUSART are suspended. Because of this, the Baud Rate Generator is inactive and a proper character reception cannot be performed. The Auto-Wake-up feature allows the controller to wake-up due to activity on the RX/DT line. This feature is available only in Asynchronous mode. The Auto-Wake-up feature is enabled by setting the WUE bit of the BAUDxCON register. Once set, the normal receive sequence on RX/DT is disabled, and the EUSART remains in an Idle state, monitoring for a wake-up event independent of the CPU mode. A wake-up event consists of a high-to-low transition on the RX/DT line. (This coincides with the start of a Sync Break or a wake-up signal character for the LIN protocol.) The EUSART module generates an RCxIF interrupt coincident with the wake-up event. The interrupt is generated synchronously to the Q clocks in normal CPU operating modes as shown in Figure 36-8, and asynchronously if the device is in Sleep mode as shown in Figure 36-9. The interrupt condition is cleared by reading the RCxREG register. The WUE bit is automatically cleared by the low-to-high transition on the RX line at the end of the Break. This signals to the user that the Break event is over. At this point, the EUSART module is in Idle mode waiting to receive the next character. 36.2.3.1 Special Considerations Break Character To avoid character errors or character fragments during a wake-up event, the wake-up character must be all zeros. When the wake-up is enabled the function works independent of the low time on the data stream. If the WUE bit is set and a valid non-zero character is received, the low time from the Start bit to the first rising edge will be interpreted as the wake-up event. The remaining bits in the character will be received as a fragmented character and subsequent characters can result in framing or overrun errors. Therefore, the initial character in the transmission must be all `0's. This must be ten or more bit times, 13bit times recommended for LIN bus, or any number of bit times for standard RS-232 devices. Oscillator Start-up Time Oscillator start-up time must be considered, especially in applications using oscillators with longer start-up intervals (i.e., LP, XT or HS/PLL mode). The Sync Break (or wake-up signal) character must be of sufficient length, and be followed by a sufficient interval, to allow enough time for the selected oscillator to start and provide proper initialization of the EUSART. WUE Bit The wake-up event causes a receive interrupt by setting the RCxIF bit. The WUE bit is cleared in hardware by a rising edge on RX/DT. The interrupt condition is then cleared in software by reading the RCxREG register and discarding its contents. To ensure that no actual data is lost, check the RCIDL bit to verify that a receive operation is not in process before setting the WUE bit. If a receive operation is not occurring, the WUE bit may then be set just prior to entering the Sleep mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 581 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Figure 36-8. Auto-Wake-up Bit (WUE) Timing During Normal Operation Rev. 10-000 326A 2/13/201 7 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 FOSC WUE bit Bit set by user Auto cleared RXx/DTx line RCxIF Cleared due to user read of RCxREG Note 1: The EUSART remains in idle while the WUE bit is set. Figure 36-9. Auto-Wake-up Bit (WUE) Timings During Sleep Rev. 10-000 327A 2/13/201 7 q1 q2 q3 q4 q1 q2 q3 q4 q2 q1 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 FOSC WUE bit Bit set by user Auto cleared RXx/DTx line RCxIF Cleared due to user read of RCxREG Sleep command executed Sleep ends Note 1: The EUSART remains in idle while the WUE bit is set. 36.2.4 Break Character Sequence The EUSART module has the capability of sending the special Break character sequences that are required by the LIN bus standard. A Break character consists of a Start bit, followed by 12 `0' bits and a Stop bit. To send a Break character, set the SENDB and TXEN bits of the TXxSTA register. The Break character transmission is then initiated by a write to the TXxREG. The value of data written to TXxREG will be ignored and all `0's will be transmitted. The SENDB bit is automatically reset by hardware after the corresponding Stop bit is sent. This allows the user to preload the transmit FIFO with the next transmit byte following the Break character (typically, the Sync character in the LIN specification). The TRMT bit of the TXxSTA register indicates when the transmit operation is active or idle, just as it does during normal transmission. See Figure 36-10 for more detail. 36.2.4.1 Break and Sync Transmit Sequence The following sequence will start a message frame header made up of a Break, followed by an auto-baud Sync byte. This sequence is typical of a LIN bus master. 1. 2. 3. Configure the EUSART for the desired mode. Set the TXEN and SENDB bits to enable the Break sequence. Load the TXxREG with a dummy character to initiate transmission (the value is ignored). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 582 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 4. 5. Write `55h' to TXxREG to load the Sync character into the transmit FIFO buffer. After the Break has been sent, the SENDB bit is reset by hardware and the Sync character is then transmitted. When the TXxREG becomes empty, as indicated by the TXxIF, the next data byte can be written to TXxREG. 36.2.5 Receiving a Break Character The EUSART module can receive a Break character in two ways. The first method to detect a Break character uses the FERR bit of the RCxSTA register and the received data as indicated by RCxREG. The Baud Rate Generator is assumed to have been initialized to the expected baud rate. A Break character has been received when all three of the following conditions are true: * * * RCxIF bit is set FERR bit is set RCxREG = 00h The second method uses the Auto-Wake-up feature described in Auto-Wake-up on Break. By enabling this feature, the EUSART will sample the next two transitions on RX/DT, cause an RCxIF interrupt, and receive the next data byte followed by another interrupt. Note that following a Break character, the user will typically want to enable the Auto-Baud Detect feature. For both methods, the user can set the ABDEN bit of the BAUDxCON register before placing the EUSART in Sleep mode. Figure 36-10. Send Break Character Sequence Dummy Write Rev. 10-000 118A 2/13/201 7 Write to TXxREG BRG Output (Shift Clock) TXx/CKx pin Start bit bit 0 36.3 bit 11 Stop bit Break TXxIF bit (Transmit Buffer Reg Empty Flag) TRMT bit (Transmit Shift Reg Empty Flag) SENDB (send break control bit) bit 1 SENDB sampled here Auto cleared EUSART Synchronous Mode Synchronous serial communications are typically used in systems with a single master and one or more slaves. The master device contains the necessary circuitry for baud rate generation and supplies the clock for all devices in the system. Slave devices can take advantage of the master clock by eliminating the internal clock generation circuitry. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 583 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... There are two signal lines in Synchronous mode: a bidirectional data line and a clock line. Slaves use the external clock supplied by the master to shift the serial data into and out of their respective receive and transmit shift registers. Since the data line is bidirectional, synchronous operation is half-duplex only. Halfduplex refers to the fact that master and slave devices can receive and transmit data but not both simultaneously. The EUSART can operate as either a master or slave device. Start and Stop bits are not used in synchronous transmissions. 36.3.1 Synchronous Master Mode The following bits are used to configure the EUSART for synchronous master operation: * SYNC = 1 (configures the EUSART for synchronous operation) * CSRC = 1 (configures the EUSART as the master) * SREN = 0 (for transmit); SREN = 1 (recommended setting to receive 1 byte) * CREN = 0 (for transmit); CREN = 1 (to receive continuously) * SPEN = 1 (enables the EUSART) Important: Clearing the SREN and CREN bits of the RCxSTA register ensures that the device is in the Transmit mode, otherwise the device will be configured to receive. 36.3.1.1 Master Clock Synchronous data transfers use a separate clock line, which is synchronous with the data. A device configured as a master transmits the clock on the TX/CK line. The TXx/CKx pin output driver is automatically enabled when the EUSART is configured for synchronous transmit or receive operation. Serial data bits change on the leading edge to ensure they are valid at the trailing edge of each clock. One clock cycle is generated for each data bit. Only as many clock cycles are generated as there are data bits. 36.3.1.2 Clock Polarity A clock polarity option is provided for Microwire compatibility. Clock polarity is selected with the SCKP bit of the BAUDxCON register. Setting the SCKP bit sets the clock Idle state as high. When the SCKP bit is set, the data changes on the falling edge of each clock. Clearing the SCKP bit sets the Idle state as low. When the SCKP bit is cleared, the data changes on the rising edge of each clock. 36.3.1.3 Synchronous Master Transmission Data is transferred out of the device on the RXx/DTx pin. The RXx/DTx and TXx/CKx pin output drivers are automatically enabled when the EUSART is configured for synchronous master transmit operation. A transmission is initiated by writing a character to the TXxREG register. If the TSR still contains all or part of a previous character the new character data is held in the TXxREG until the last bit of the previous character has been transmitted. If this is the first character, or the previous character has been completely flushed from the TSR, the data in the TXxREG is immediately transferred to the TSR. The transmission of the character commences immediately following the transfer of the data to the TSR from the TXxREG. Each data bit changes on the leading edge of the master clock and remains valid until the subsequent leading clock edge. Note: The TSR register is not mapped in data memory, so it is not available to the user. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 584 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.3.1.4 Synchronous Master Transmission Setup 1. Initialize the SPxBRGH, SPxBRGL register pair and the BRG16 bit to achieve the desired baud rate (see EUSART Baud Rate Generator (BRG)). 2. Select the transmit output pin by writing the appropriate values to the RxyPPS register and RXxPPS register. Both selections should enable the same pin. 3. Select the clock output pin by writing the appropriate values to the RxyPPS register and CKxPPS register. Both selections should enable the same pin. 4. Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. 5. Disable Receive mode by clearing bits SREN and CREN. 6. Enable Transmit mode by setting the TXEN bit. 7. If 9-bit transmission is desired, set the TX9 bit. 8. If interrupts are desired, set the TXxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. 9. If 9-bit transmission is selected, the ninth bit should be loaded in the TX9D bit. 10. Start transmission by loading data to the TXxREG register. Figure 36-11. Synchronous Transmission Rev. 10-000 115A 2/7/201 7 Word 1 Write to TXxREG BRG Output (Shift Clock) TXx/CKx pin TXxIF bit (Transmit Buffer Reg Empty Flag) TRMT bit (Transmit Shift Reg Empty Flag) Start bit bit 0 bit 1 bit 7/8 Stop bit Word 1 1 TCY 36.3.1.5 Synchronous Master Reception Data is received at the RXx/DTx pin. The RXx/DTx pin output driver is automatically disabled when the EUSART is configured for synchronous master receive operation. In Synchronous mode, reception is enabled by setting either the Single Receive Enable bit (SREN of the RCxSTA register) or the Continuous Receive Enable bit (CREN of the RCxSTA register). When SREN is set and CREN is clear, only as many clock cycles are generated as there are data bits in a single character. The SREN bit is automatically cleared at the completion of one character. When CREN is set, clocks are continuously generated until CREN is cleared. If CREN is cleared in the middle of a character the CK clock stops immediately and the partial character is discarded. If SREN and CREN are both set, then SREN is cleared at the completion of the first character and CREN takes precedence. To initiate reception, set either SREN or CREN. Data is sampled at the RXx/DTx pin on the trailing edge of the TX/CK clock pin and is shifted into the Receive Shift Register (RSR). When a complete character is received into the RSR, the RCxIF bit is set and the character is automatically transferred to the two character receive FIFO. The Least Significant eight bits of the top character in the receive FIFO are available in RCxREG. The RCxIF bit remains set as long as there are unread characters in the receive FIFO. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 585 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Note: If the RX/DT function is on an analog pin, the corresponding ANSEL bit must be cleared for the receiver to function. 36.3.1.6 Receive Overrun Error The receive FIFO buffer can hold two characters. An overrun error will be generated if a third character, in its entirety, is received before RCxREG is read to access the FIFO. When this happens the OERR bit of the RCxSTA register is set. Previous data in the FIFO will not be overwritten. The two characters in the FIFO buffer can be read, however, no additional characters will be received until the error is cleared. The OERR bit can only be cleared by clearing the overrun condition. If the overrun error occurred when the SREN bit is set and CREN is clear then the error is cleared by reading RCxREG. If the overrun occurred when the CREN bit is set then the error condition is cleared by either clearing the CREN bit of the RCxSTA register or by clearing the SPEN bit which resets the EUSART. 36.3.1.7 Receiving 9-Bit Characters The EUSART supports 9-bit character reception. When the RX9 bit of the RCxSTA register is set the EUSART will shift nine bits into the RSR for each character received. The RX9D bit of the RCxSTA register is the ninth, and Most Significant, data bit of the top unread character in the receive FIFO. When reading 9-bit data from the receive FIFO buffer, the RX9D data bit must be read before reading the eight Least Significant bits from the RCxREG. 36.3.1.8 Synchronous Master Reception Setup 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Initialize the SPxBRGH:SPxBRGL register pair and set or clear the BRG16 bit, as required, to achieve the desired baud rate. Select the receive input pin by writing the appropriate values to the RxyPPS register and RXxPPS register. Both selections should enable the same pin. Select the clock output pin by writing the appropriate values to the RxyPPS register and CKxPPS register. Both selections should enable the same pin. Clear the ANSEL bit for the RXx pin (if applicable). Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. Ensure bits CREN and SREN are clear. If interrupts are desired, set the RCxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. If 9-bit reception is desired, set bit RX9. Start reception by setting the SREN bit or for continuous reception, set the CREN bit. Interrupt flag bit RCxIF will be set when reception of a character is complete. An interrupt will be generated if the enable bit RCxIE was set. Read the RCxSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCxREG register. If an overrun error occurs, clear the error by either clearing the CREN bit of the RCxSTA register or by clearing the SPEN bit which resets the EUSART. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 586 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Figure 36-12. Synchronous Reception (Master Mode, SREN) Rev. 10-000 121A 2/13/201 7 RXx/DTx pin bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 TXx/CKx pin SCKP = 0 TXx/CKx pin SCKP = 1 Write to SREN SREN bit CREN bit `0' `0' RCxIF (Interrupt) Read RCxREG 36.3.2 Synchronous Slave Mode The following bits are used to configure the EUSART for synchronous slave operation: * SYNC = 1 (configures the EUSART for synchronous operation.) * CSRC = 0 (configures the EUSART as a slave) * SREN = 0 (for transmit); SREN = 1 (for single byte receive) * CREN = 0 (for transmit); CREN = 1 (recommended setting for continuous receive) * SPEN = 1 (enables the EUSART) Important: Clearing the SREN and CREN bits of the RCxSTA register ensures that the device is in the Transmit mode, otherwise the device will be configured to receive. 36.3.2.1 Slave Clock Synchronous data transfers use a separate clock line, which is synchronous with the data. A device configured as a slave receives the clock on the TX/CK line. The TXx/CKx pin output driver is automatically disabled when the device is configured for synchronous slave transmit or receive operation. Serial data bits change on the leading edge to ensure they are valid at the trailing edge of each clock. One data bit is transferred for each clock cycle. Only as many clock cycles should be received as there are data bits. Important: If the device is configured as a slave and the TX/CK function is on an analog pin, the corresponding ANSEL bit must be cleared. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 587 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.3.2.2 EUSART Synchronous Slave Transmit The operation of the Synchronous Master and Slave modes are identical (see Synchronous Master Transmission), except in the case of the Sleep mode. If two words are written to the TXxREG and then the SLEEP instruction is executed, the following will occur: 1. 2. 3. The first character will immediately transfer to the TSR register and transmit. The second word will remain in the TXxREG register. The TXxIF bit will not be set. 4. After the first character has been shifted out of TSR, the TXxREG register will transfer the second character to the TSR and the TXxIF bit will now be set. If the PEIE and TXxIE bits are set, the interrupt will wake the device from Sleep and execute the next instruction. If the GIE bit is also set, the program will call the Interrupt Service Routine. 5. 36.3.2.3 Synchronous Slave Transmission Setup 1. 2. Set the SYNC and SPEN bits and clear the CSRC bit. Select the transmit output pin by writing the appropriate values to the RxyPPS register and RXxPPS register. Both selections should enable the same pin. 3. Select the clock input pin by writing the appropriate value to the CKxPPS register. 4. Clear the ANSEL bit for the CKx pin (if applicable). 5. Clear the CREN and SREN bits. 6. If interrupts are desired, set the TXxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. 7. If 9-bit transmission is desired, set the TX9 bit. 8. Enable transmission by setting the TXEN bit. 9. If 9-bit transmission is selected, insert the Most Significant bit into the TX9D bit. 10. Prepare for transmission by writing the Least Significant eight bits to the TXxREG register. The word will be transmitted in response to the Master clocks at the CKx pin. 36.3.2.4 EUSART Synchronous Slave Reception The operation of the Synchronous Master and Slave modes is identical (see Synchronous Master Reception), with the following exceptions: * * * Sleep CREN bit is always set, therefore the receiver is never idle SREN bit, which is a "don't care" in Slave mode A character may be received while in Sleep mode by setting the CREN bit prior to entering Sleep. Once the word is received, the RSR register will transfer the data to the RCxREG register. If the RCxIE enable bit is set, the interrupt generated will wake the device from Sleep and execute the next instruction. If the GIE bit is also set, the program will branch to the interrupt vector. 36.3.2.5 Synchronous Slave Reception Setup: 1. 2. 3. 4. 5. Set the SYNC and SPEN bits and clear the CSRC bit. Select the receive input pin by writing the appropriate value to the RXxPPS register. Select the clock input pin by writing the appropriate values to the CKxPPS register. Clear the ANSEL bit for both the TXx/CKx and RXx/DTx pins (if applicable). If interrupts are desired, set the RCxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 588 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 6. 7. 8. If 9-bit reception is desired, set the RX9 bit. Set the CREN bit to enable reception. The RCxIF bit will be set when reception is complete. An interrupt will be generated if the RCxIE bit was set. 9. If 9-bit mode is enabled, retrieve the Most Significant bit from the RX9D bit of the RCxSTA register. 10. Retrieve the eight Least Significant bits from the receive FIFO by reading the RCxREG register. 11. If an overrun error occurs, clear the error by either clearing the CREN bit of the RCxSTA register or by clearing the SPEN bit which resets the EUSART. 36.4 EUSART Operation During Sleep The EUSART will remain active during Sleep only in the Synchronous Slave mode. All other modes require the system clock and therefore cannot generate the necessary signals to run the Transmit or Receive Shift registers during Sleep. Synchronous Slave mode uses an externally generated clock to run the Transmit and Receive Shift registers. 36.4.1 Synchronous Receive During Sleep To receive during Sleep, all the following conditions must be met before entering Sleep mode: * * * RCxSTA and TXxSTA Control registers must be configured for Synchronous Slave Reception (see Synchronous Slave Reception Setup:). If interrupts are desired, set the RCxIE bit of the PIEx register and the GIE and PEIE bits of the INTCON register. The RCxIF interrupt flag must be cleared by reading RCxREG to unload any pending characters in the receive buffer. Upon entering Sleep mode, the device will be ready to accept data and clocks on the RXx/DTx and TXx/CKx pins, respectively. When the data word has been completely clocked in by the external device, the RCxIF interrupt flag bit of the PIRx register will be set. Thereby, waking the processor from Sleep. Upon waking from Sleep, the instruction following the SLEEP instruction will be executed. If the Global Interrupt Enable (GIE) bit of the INTCON register is also set, then the Interrupt Service Routine at address 004h will be called. 36.4.2 Synchronous Transmit During Sleep To transmit during Sleep, all the following conditions must be met before entering Sleep mode: * * * * The RCxSTA and TXxSTA Control registers must be configured for synchronous slave transmission (see Synchronous Slave Transmission Setup). The TXxIF interrupt flag must be cleared by writing the output data to the TXxREG, thereby filling the TSR and transmit buffer. Interrupt enable bits TXxIE of the PIEx register and PEIE of the INTCON register must set. If interrupts are desired, set the GIEx bit of the INTCON register. Upon entering Sleep mode, the device will be ready to accept clocks on the TXx/CKx pin and transmit data on the RXx/DTx pin. When the data word in the TSR has been completely clocked out by the external device, the pending byte in the TXxREG will transfer to the TSR and the TXxIF flag will be set. Thereby, waking the processor from Sleep. At this point, the TXxREG is available to accept another character for transmission. Writing TXxREG will clear the TXxIF flag. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 589 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Upon waking from Sleep, the instruction following the SLEEP instruction will be executed. If the Global Interrupt Enable (GIE) bit is also set then the Interrupt Service Routine at address 0004h will be called. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 590 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.5 Register Summary - EUSART Offset Name Bit Pos. 0x0119 RC1REG 7:0 0x011A TX1REG 7:0 TXREG[7:0] 7:0 SPBRGL[7:0] RCREG[7:0] 0x011B SP1BRG 0x011D RC1STA 7:0 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0x011E TX1STA 7:0 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0x011F BAUD1CON 7:0 ABDOVF RCIDL SCKP BRG16 WUE ABDEN 36.6 15:8 SPBRGH[7:0] Register Definitions: EUSART Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 591 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.6.1 RCxSTA Name: Offset: RCxSTA 0x011D Receive Status and Control Register Bit Access Reset 7 6 5 4 3 2 1 0 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D R/W R/W R/W R/W R/W RO R/HC R/HC 0 0 0 0 0 0 0 0 Bit 7 - SPEN Serial Port Enable bit Value 1 0 Description Serial port enabled Serial port disabled (held in Reset) Bit 6 - RX9 9-Bit Receive Enable bit Value 1 0 Description Selects 9-bit reception Selects 8-bit reception Bit 5 - SREN Single Receive Enable bit Controls reception. This bit is cleared by hardware when reception is complete Value 1 0 X Condition SYNC = 1 AND CSRC = 1 SYNC = 1 AND CSRC = 1 SYNC = 0 OR CSRC = 0 Description Start single receive Single receive is complete Don't care Bit 4 - CREN Continuous Receive Enable bit Value 1 0 1 0 Condition Description SYNC = 1 Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) SYNC = 1 Disables continuous receive SYNC = 0 Enables receiver SYNC = 0 Disables receiver Bit 3 - ADDEN Address Detect Enable bit Value 1 0 X Condition Description SYNC = 0 AND RX9 = 1 The receive buffer is loaded and the interrupt occurs only when the ninth received bit is set SYNC = 0 AND RX9 = 1 All bytes are received and interrupt always occurs. Ninth bit can be used as parity bit RX9 = 0 OR SYNC = 1 Don't care (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 592 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Bit 2 - FERR Framing Error bit Value 1 0 Description Unread byte in RCxREG has a framing error Unread byte in RCxREG does not have a framing error Bit 1 - OERR Overrun Error bit Value 1 0 Description Overrun error (can be cleared by clearing either SPEN or CREN bit) No overrun error Bit 0 - RX9D Ninth bit of Received Data This can be address/data bit or a parity bit which is determined by user firmware. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 593 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.6.2 TXxSTA Name: Offset: TXxSTA 0x011E Transmit Status and Control Register Bit Access Reset 7 6 5 4 3 2 1 0 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D R/W R/W R/W R/W R/W R/W RO R/W 0 0 0 0 0 0 1 0 Bit 7 - CSRC Clock Source Select bit Value 1 0 X Condition SYNC= 1 SYNC= 1 SYNC= 0 Description Master mode (clock generated internally from BRG) Slave mode (clock from external source) Don't care Bit 6 - TX9 9-bit Transmit Enable bit Value 1 0 Description Selects 9-bit transmission Selects 8-bit transmission Bit 5 - TXEN Transmit Enable bit Enables transmitter(1) Value 1 0 Description Transmit enabled Transmit disabled Bit 4 - SYNC EUSART Mode Select bit Value 1 0 Description Synchronous mode Asynchronous mode Bit 3 - SENDB Send Break Character bit Value 1 0 X Condition SYNC= 0 SYNC= 0 SYNC= 1 Description Send Sync Break on next transmission (cleared by hardware upon completion) Sync Break transmission disabled or completed Don't care Bit 2 - BRGH High Baud Rate Select bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 594 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Value 1 0 X Condition SYNC= 0 SYNC= 0 SYNC= 1 Description High speed, if BRG16 = 1, baud rate is baudclk/4; else baudclk/16 Low speed Don't care Bit 1 - TRMT Transmit Shift Register (TSR) Status bit Value 1 0 Description TSR is empty TSR is not empty Bit 0 - TX9D Ninth bit of Transmit Data Can be address/data bit or a parity bit. Note: 1. SREN and CREN bits override TXEN in Sync mode. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 595 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.6.3 BAUDxCON Name: Offset: BAUDxCON 0x011F Baud Rate Control Register Bit Access Reset 7 6 4 3 1 0 ABDOVF RCIDL 5 SCKP BRG16 2 WUE ABDEN RO RO RW RW RW RW 0 0 0 0 0 0 Bit 7 - ABDOVF Auto-Baud Detect Overflow bit Value 1 0 X Condition SYNC= 0 SYNC= 0 SYNC= 1 Description Auto-baud timer overflowed Auto-baud timer did not overflow Don't care Bit 6 - RCIDL Receive Idle Flag bit Value 1 0 X Condition SYNC= 0 SYNC= 0 SYNC= 1 Description Receiver is Idle Start bit has been received and the receiver is receiving Don't care Bit 4 - SCKP Synchronous Clock Polarity Select bit Value 1 0 1 0 Condition SYNC= 0 SYNC= 0 SYNC= 1 SYNC= 1 Description Idle state for transmit (TX) is a low level (transmit data inverted) Idle state for transmit (TX) is a high level (transmit data is non-inverted) Data is clocked on rising edge of the clock Data is clocked on falling edge of the clock Bit 3 - BRG16 16-bit Baud Rate Generator Select bit Value 1 0 Description 16-bit Baud Rate Generator is used 8-bit Baud Rate Generator is used Bit 1 - WUE Wake-up Enable bit Value 1 0 X Condition Description SYNC= 0 Receiver is waiting for a falling edge. Upon falling edge no character will be received and flag RCxIF will be set. WUE will automatically clear after RCxIF is set. SYNC= 0 Receiver is operating normally SYNC= 1 Don't care Bit 0 - ABDEN Auto-Baud Detect Enable bit (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 596 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... Value 1 0 X Condition SYNC= 0 SYNC= 0 SYNC= 1 Description Auto-Baud Detect mode is enabled (clears when auto-baud is complete) Auto-Baud Detect is complete or mode is disabled Don't care (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 597 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.6.4 SPxBRG Name: Offset: SPxBRG 0x011B Baud Rate Determination Register Bit 15 14 13 12 11 10 9 8 SPBRGH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 SPBRGL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 15:8 - SPBRGH[7:0] Baud Rate High Byte Register Bits 7:0 - SPBRGL[7:0] Baud Rate Low Byte Register (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 598 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.6.5 RCxREG Name: Offset: RCxREG 0x0119 Receive Data Register Bit 7 6 5 4 3 2 1 0 RCREG[7:0] Access Reset RO RO RO RO RO RO RO RO 0 0 0 0 0 0 0 0 Bits 7:0 - RCREG[7:0] Receive data (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 599 PIC16(L)F18424/44 (EUSART) Enhanced Universal Synchronous Asyn... 36.6.6 TXxREG Name: Offset: TXxREG 0x011A Transmit Data Register Bit 7 6 5 4 3 2 1 0 TXREG[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 - TXREG[7:0] Transmit Data (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 600 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37. (SMT) Signal Measurement Timer The SMT is a 24-bit counter with advanced clock and gating logic, which can be configured for measuring a variety of digital signal parameters such as pulse width, frequency and duty cycle, and the time difference between edges on two signals. Features of the SMT include: * 24-bit timer/counter * Two 24-bit measurement capture registers * One 24-bit period match register * Filename: Multi-mode operation, including relative timing measurement 10-000161E.vsd Title: Signal Measurement Timer v1 * Interrupt on period match and acquisition complete Last Edit: 10/12/2016 * First Multiple signal and window sources Used: clock, PIC18(L)F2x/4xK42 Notes: Below is the block diagram for the SMT module. Figure 37-1. Signal Measurement Timer Block Diagram Rev. 10-000161E 10/12/2016 Period Latch SMT_window SMT Clock Sync Circuit SMT_signal SMT Clock Sync Circuit Set SMTxPRAIF SMTxPR Control Logic Set SMTxIF Comparator Reset Enable CLKR 111 SOSC 110 MFINTOSC/16 101 MFINTOSC 100 LFINTOSC 011 HFINTOSC 010 FOSC 001 FOSC/4 000 SMTxTMR Window Latch 24-bit Buffer SMTxCPR 24-bit Buffer SMTxCPW Set SMTxPWAIF Prescaler CSEL<2:0> 37.1 SMT Operation 37.1.1 Clock Source Selection The SMT clock source is selected by configuring the CSEL bits in the SMTxCLK register. The clock source can be prescaled using the PS bits of the SMTxCON0 register. The prescaled clock source is (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 601 PIC16(L)F18424/44 (SMT) Signal Measurement Timer used to clock both the counter and any synchronization logic used by the module. Refer the table below for possible clock source options. The polarity of the clock source can be selected using the CPOL bit in the SMTxCON0 register. Table 37-1. SMT Clock Source Selection 37.1.2 CSEL<2:0> Clock Source 111 CLKREF output 110 SOSC 101 MFINTOSC (31.25kHz) 100 MFINTOSC (500kHz) 011 LFINTOSC 010 HFINTOSC 001 FOSC 000 FOSC/4 Signal and Window Source Selection The SMT signal and window sources are selected by configuring the SSEL bits in the SMTxSIG register and the WSEL bits in the SMTxWIN register. Refer the tables below for the possible selections. The polarity of the signal and window sources can be selected using the SPOL and WPOL bits in the SMTxCON0 register. Table 37-2. SMT Signal Selection SSEL<4:0> SMT1 Signal Source 11111-10110 Reserved 10101 CLC4OUT 10100 CLC3OUT 10011 CLC2OUT 10010 CLC1OUT 10001 ZCDOUT 10000 C2OUT 01111 C1OUT 01110 NCO1OUT 01101 PWM7OUT 01100 PWM6OUT 01011 CCP4OUT 01010 CCP3OUT 01001 CCP2OUT (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 602 PIC16(L)F18424/44 (SMT) Signal Measurement Timer SSEL<4:0> SMT1 Signal Source 01000 CCP1OUT 00111 TMR6 postscaled output 00110 TMR5 overflow 00101 TMR4 postscaled output 00100 TMR3 overflow 00011 TMR2 postscaled output 00010 TMR1 overflow 00001 TMR0 overflow 00000 Pin Selected by SMT1SIGPPS Table 37-3. SMT Window Selection WSEL<4:0> SMT1 Window Source 11111-11000 Reserved 10111 NCO1OUT 10110 Reserved 10101 CLKREFOUT 10100 CLC4OUT 10011 CLC3OUT 10010 CLC2OUT 10001 CLC1OUT 10000 ZCDOUT 01111 C2OUT 01110 C1OUT 01101 PWM7OUT 01100 PWM6OUT 01011 CCP4OUT 01010 CCP3OUT 01001 CCP2OUT 01000 CCP1OUT 00111 TMR6_postscaled_out 00110 TMR4_postscaled_out 00101 TMR2_postscaled_out (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 603 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.1.3 WSEL<4:0> SMT1 Window Source 00100 TMR0_overflow 00011 SOSC 00010 MFINTOSC (31.25kHz) 00001 LFINTOSC (31.25kHz) 00000 Pin Selected by SMT1WINPPS Time Base The SMTxTMR is the 24-bit counter/timer used for measurement in each of the modes of the SMT. It can be reset to 0x000000 by setting the RST bit of the SMTxSTAT register. It can be written to and read by software. It is not guarded for atomic access, therefore reads and writes to the SMTxTMR should be made when the GO = 0. The counter can be prevented from a rollover using the STP bit in the SMTxCON0 register. When STP = 1, SMTxTMR will remain equal to SMTxPR. When STP = 0, SMTxTMR resets to 0x000000. 37.1.4 Capture Pulse Width and Period Registers The SMTxCPW and SMTxCPR registers are used to latch in the value of the SMTxTMR based on the mode of SMT operation. These registers can also be updated with the current value of the SMTxTMR value by setting the CPWUP and CPRUP bits of the SMTxSTAT register, respectively. 37.1.5 Status Information The SMT provides input status information for the user without requiring the need to deal with the polarity of the incoming signals. Go Status: Timer run status is determined by the TS bit of the SMTxSTAT register, and will be delayed in time by synchronizer delays in non-Counter modes. Signal Status:Signal status is determined by the AS bit of the SMTxSTAT register. This bit is used in all modes except Window Measure, Time of Flight and Capture modes, and is only valid when TS = 1, and will be delayed in time by synchronizer delays in non-Counter modes. Window Status: Window status is determined by the WS bit of the SMTxSTAT register. This bit is only used in Windowed Measure, Gated Counter and Gated Window Measure modes, and is only valid when TS = 1, and will be delayed in time by synchronizer delays in non-Counter modes. 37.1.6 Modes of Operation The modes of operation are mentioned in the table below. The following sections provide descriptions and examples of how the modes can be used. Note that all waveforms assume WPOL/SPOL/CPOL = 0. For all modes, the REPEAT bit controls whether the acquisition is repeated or single. When REPEAT = 0 (Single Acquisition mode), the timer will stop incrementing and the SMTxGO bit will be reset upon the completion of an acquisition. Otherwise, the timer will continue and allow for continued acquisitions to overwrite the previous ones until the timer is stopped in software. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 604 PIC16(L)F18424/44 (SMT) Signal Measurement Timer Table 37-4. Modes of Operation MODE Mode of operation Synchronous operation 0000 Timer Yes 0001 Gated Timer Yes 0010 Period and Duty Cycle Measurement Yes 0011 High and low time Measurement Yes 0100 Windowed Measurement Yes 0101 Gated Windowed Measurement Yes 0110 Time of Flight Measurement Yes 0111 Capture Yes 1000 Counter No 1001 Gated Counter No 1010 Windowed Counter No 1011-1111 Reserved - 37.1.6.1 Timer Mode Filename: 10-000174A.vsd Timer modeTIMER is the basic mode of operation where the SMTxTMR is used as a 24-bit timer. No data Title: MODE TIMING DIAGRAM Last Edit: 12/19/2013 acquisition takes place LECQ in this mode. The timer increments as long as the SMTxGO bit has been set First Used: PIC16(L)F1612/3 Notes: by software. No SMT window or SMT signal events affect the SMTxGO bit. Everything is synchronized to the SMT clock source. When the timer experiences a period match (SMTxTMR = SMTxPR), SMTxTMR is reset and the period match interrupt trips. See figure below. Figure 37-2. Timer Mode Timing Diagram Rev. 10-000 174A 12/19/201 3 SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxPR SMTxTMR 11 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 SMTxIF 37.1.6.2 Gated Timer Mode Gated Timer mode uses the signal input (SSEL) to control whether or not the SMTxTMR will increment. Upon a falling edge of the signal, the SMTxCPW register will update to the current value of the SMTxTMR. Example waveforms for both repeated and single acquisitions are provided in figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 605 Filename: Title: Last Edit: First Used: Notes: 10-000176A.vsd GATED TIMER MODE REPEAT ACQUISITION TIMING DIAGRAM 12/19/2013 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-3. Gated Timer Mode, Repeat Acquisition Timing Diagram Rev. 10-000 176A 12/19/201 3 SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync Filename: SMTxPR 10-000175A.vsd 0xFFFFFF Title: GATED TIMER MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: SMTxTMR 12/19/2013 0 1 2 3 4 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxCPW 5 6 7 5 7 SMTxPWAIF Figure 37-4. Gated Timer Mode, Single Acquisition Timing Diagram Rev. 10-000 175A 12/19/201 3 SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxPR SMTxTMR 0xFFFFFF 0 1 2 3 4 5 SMTxCPW 5 SMTxPWAIF 37.1.6.3 Period and Duty Cycle Measurement Mode In this mode, either the duty cycle or period (depending on polarity) of the input signal can be acquired relative to the SMT clock. The CPW register is updated on a falling edge of the signal, and the CPR register is updated on a rising edge of the signal, along with the SMTxTMR resetting to 0x000001. In addition, the SMTxGO bit is reset on a rising edge when the SMT is in single acquisition mode. See figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 606 Filename: Title: Last Edit: First Used: Notes: 10-000177A.vsd PERIOD AND DUTY-CYCLE REPEAT ACQUISITION MODE TIMING DIAGRAM 12/19/2013 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-5. Period and Duty-Cycle, Repeat Acquisition Mode Timing Diagram Rev. 10-000 177A 12/19/201 3 SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 6 7 8 Filename: SMTxCPW 10-000178A.vsd Title: PERIOD AND DUTY-CYCLE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: SMTxCPR 12/19/2013 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxPWAIF 9 10 11 1 2 3 4 5 5 2 11 SMTxPRAIF Figure 37-6. Period and Duty-Cycle, Single Acquisition Mode Timing Diagram Rev. 10-000 178A 12/19/201 3 SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 6 7 SMTxCPW 8 9 10 11 5 SMTxCPR 11 SMTxPWAIF SMTxPRAIF 37.1.6.4 High and Low Measurement Mode This mode measures the high and low pulse time of the signal relative to the SMT clock. It begins incrementing the SMTxTMR on a rising edge on the input signal, then updates the SMTxCPW register with the value and resets the SMTxTMR on a falling edge, starting to increment again. Upon observing another rising edge, it updates the SMTxCPR register with its current value and once again resets the SMTxTMR value and begins incrementing again. See the figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 607 Filename: Title: Last Edit: First Used: Notes: 10-000180A.vsd HIGH AND LOW MEASURE MODE REPEAT ACQUISITION TIMING DIAGRAM 12/19/2013 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-7. High and Low Measurement Mode, Repeat Acquisition Timing Diagram Rev. 10-000 180A 12/19/201 3 SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 1 2 3 Filename: SMTxCPW 10-000179A.vsd Title: HIGH AND LOW MEASURE MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: SMTxCPR 12/19/2013 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxPWAIF 4 5 6 1 2 1 2 3 5 2 6 SMTxPRAIF Figure 37-8. High and Low Measurement Mode, Single Acquisition Timing Diagram Rev. 10-000 179A 12/19/201 3 SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 1 2 SMTxCPW 3 4 5 6 5 SMTxCPR 6 SMTxPWAIF SMTxPRAIF 37.1.6.5 Windowed Measurement Mode This mode measures the duration of the window input (WSEL) to the SMT. It begins incrementing the timer on a rising edge of the window input and updates the SMTxCPR register with the value of the timer and resets the timer on a second rising edge. See figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 608 Filename: Title: Last Edit: First Used: Notes: 10-000182A.vsd WINDOWED MEASURE MODE REPEAT ACQUISITION TIMING DIAGRAM 12/19/2013 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-9. Windowed Measurement Mode, Repeat Acquisition Timing Diagram Rev. 10-000 182A 12/19/201 3 SMTxWIN SMTxWIN_sync SMTx Clock SMTxEN SMTxGO SMTxGO_sync Filename: 10-000181A.vsd Title: WINDOWED MEASURE MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: SMTxTMR 12/19/2013 0 1 2 3 4 5 6 7 8 9 10 11 12 1 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxCPR 2 3 4 5 6 7 8 1 12 2 3 4 8 SMTxPRAIF Figure 37-10. Windowed Measurement Mode, Single Acquisition Timing Diagram Rev. 10-000 181A 12/19/201 3 SMTxWIN SMTxWIN_sync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 6 7 8 9 10 11 12 SMTxCPR 12 SMTxPRAIF 37.1.6.6 Gated Window Measurement Mode This mode measures the duty cycle of the signal input over a known input window. It does so by incrementing the timer on each pulse of the clock signal while the signal input is high, updating the SMTxCPR register and resetting the timer on every rising edge of the window input after the first. See figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 609 Filename: Title: Last Edit: First Used: Notes: 10-000184A.vsd GATED WINDOWED MEASURE MODE REPEAT ACQUISITION TIMING DIAGRAM 12/19/2013 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-11. Gated Windowed Measurement Mode, Repeat Acquisition Timing Diagram Rev. 10-000 184A 12/19/201 3 SMTxWIN SMTxWIN_sync SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync10-000183A.vsd Filename: Title: GATED WINDOWED MEASURE MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit:SMTxTMR 12/19/2013 0 1 2 3 4 5 6 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxCPR 0 1 2 3 6 0 3 SMTxPRAIF Figure 37-12. Gated Windowed Measurement Mode, Single Acquisition Timing Diagram Rev. 10-000 183A 12/19/201 3 SMTxWIN SMTxWIN_sync SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 SMTxCPR 6 6 SMTxPRAIF 37.1.6.7 Time of Flight Measurement Mode This mode measures the time interval between a rising edge on the window input and a rising edge on the signal input, beginning to increment the timer upon observing a rising edge on the window input, while updating the SMTxCPR register and resetting the timer upon observing a rising edge on the signal input. In the event of two rising edges of the window signal without a signal rising edge, it will update the SMTxCPW register with the current value of the timer and reset the timer value. See figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 610 Title: Last Edit: First Used: Notes: TIME OF FLIGHT MODE REPEAT ACQUISITION TIMING DIAGRAM 4/22/2016 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-13. Time of Flight Mode, Repeat Acquisition Timing Diagram Rev. 10-000186A 4/22/2016 SMTxWIN SMTxWIN_sync SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 Filename: 10-000185A.vsd Title: SMTxCPW TIME OF FLIGHT MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: 4/26/2016 First Used: SMTxCPR PIC16(L)F1612/3 LECQ Notes: 1 2 3 4 5 6 7 8 2 9 10 11 12 13 1 13 4 SMTxPWAIF SMTxPRAIF Figure 37-14. Time of Flight Mode, Single Acquisition Timing Diagram Rev. 10-000185A 4/26/2016 SMTxWIN SMTxWIN_sync SMTx_signal SMTx_signalsync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 SMTxCPW SMTxCPR 4 SMTxPWAIF SMTxPRAIF 37.1.6.8 Capture Mode This mode captures the timer value based on a rising or falling edge on the window input and triggers an interrupt. This mimics the capture feature of a CCP module. The timer begins incrementing upon the SMTxGO bit being set, and updates the value of the SMTxCPR register on each rising edge of window signal, and updates the value of the SMTxCPW register on each falling edge of the window signal. The timer is not reset by any hardware conditions in this mode and must be reset by software, if desired. See figures below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 611 Filename: Title: Last Edit: First Used: Notes: 10-000188A.vsd CAPTURE MODE REPEAT ACQUISITION TIMING DIAGRAM 12/19/2013 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-15. Capture Mode, Repeat Acquisition Timing Diagram Rev. 10-000 188A 12/19/201 3 SMTxWIN SMTxWIN_sync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SMTxCPW 3 Filename: 10-000187A.vsd Title: CAPTURE MODE SINGLE ACQUISITION TIMING DIAGRAM 2 Last Edit: SMTxCPR 12/19/2013 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxPWAIF 19 18 32 31 SMTxPRAIF Figure 37-16. Capture Mode, Single Acquisition Timing Diagram Rev. 10-000 187A 12/19/201 3 SMTxWIN SMTxWIN_sync SMTx Clock SMTxEN SMTxGO SMTxGO_sync SMTxTMR 0 1 2 3 SMTxCPW SMTxCPR 3 2 SMTxPWAIF SMTxPRAIF 37.1.6.9 Counter Mode This mode increments the timer on each pulse of the signal input. This mode is asynchronous to the SMT clock and uses the signal input as a time source. The SMTxCPW register will be updated with the current SMTxTMR value on the falling edge of the window input. See figure below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 612 Title: Last Edit: First Used: Notes: COUNTER MODE TIMING DIAGRAM 4/12/2016 PIC16(L)F1612/3 LECQ PIC16(L)F18424/44 (SMT) Signal Measurement Timer Figure 37-17. Counter Mode Timing Diagram Rev. 10-000189A 4/12/2016 SMTxWIN SMTx_signal SMTxEN SMTxGO SMTxTMR 0 1 2 3 4 5 6 7 8 SMTxCPW Filename: Title: Last Edit: First 37.1.6.10Used: Gated Notes: 27 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 12 25 10-000190A.vsd GATED COUNTER MODE REPEAT ACQUISITION TIMING DIAGRAM 12/18/2013 PIC16(L)F1612/3 Counter ModeLECQ This mode counts pulses on the signal input, gated by the window input. It begins incrementing the timer upon seeing a rising edge of the window input and updates the SMTxCPW register upon a falling edge on the window input. See figures below. Figure 37-18. Gated Counter Mode, Repeat Acquisition Timing Diagram Rev. 10-000190A 12/18/2013 SMTxWIN SMTx_signal SMTxEN Filename: SMTxGO10-000191A.vsd Title: GATED COUNTER MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: SMTxTMR12/18/2013 0 1 2 3 4 5 6 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxCPW 7 8 9 10 11 12 8 13 13 SMTxPWAIF Figure 37-19. Gated Counter Mode, Single Acquisition Timing Diagram Rev. 10-000191A 12/18/2013 SMTxWIN SMTx_signal SMTxEN SMTxGO SMTxTMR 0 1 2 3 4 5 6 7 SMTxCPW 8 8 SMTxPWAIF 37.1.6.11 Windowed Counter Mode This mode counts pulses on the signal input, within a window dictated by the window input. It begins counting upon seeing a rising edge of the window input, updates the SMTxCPW register on a falling edge (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 613 Filename: Title: Last Edit: First Used: Notes: PIC16(L)F18424/44 10-000192A.vsd WINDOWED COUNTER MODE REPEAT ACQUISITION TIMING DIAGRAM 12/18/2013 PIC16(L)F1612/3 LECQ (SMT) Signal Measurement Timer of the window input, and updates the SMTxCPR register on each rising edge of the window input after the first. See figures below. Figure 37-20. Windowed Counter Mode, Repeat Acquisition Timing Diagram Rev. 10-000192A 12/18/2013 SMTxWIN SMTx_signal SMTxEN SMTxGO SMTxTMR 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 Filename: SMTxCPW 10-000193A.vsd Title: WINDOWED COUNTER MODE SINGLE ACQUISITION TIMING DIAGRAM Last Edit: SMTxCPR 12/18/2013 First Used: PIC16(L)F1612/3 LECQ Notes: SMTxPWAIF 2 3 4 9 5 5 16 SMTxPRAIF Figure 37-21. Windowed Counter Mode, Single Acquisition Timing Diagram Rev. 10-000193A 12/18/2013 SMTxWIN SMTx_signal SMTxEN SMTxGO SMTxTMR 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SMTxCPW 9 16 SMTxCPR SMTxPWAIF SMTxPRAIF 37.1.7 Interrupts The SMT has three interrupts: * Pulse Width Acquisition Interrupt (SMTxPWAIF): Interrupt triggers when SMTxCPW is updated * Period Acquisition Interrupt (SMTxPRAIF): Interrupt triggers when SMTxCPR is updated * Counter Period Match Interrupt (SMTxIF): Interrupt triggers when SMTxTMR equals SMTxPR Each of the above interrupts can be enabled/disabled using the corresponding bits in the PIEx register. 37.1.8 Operation During Sleep The SMT can operate during SLEEP, IDLE, and DOZE modes; provided that the clock and signal sources continue to function. System clock sources, like FOSC and FOSC/4, are disabled in Sleep. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 614 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.2 Offset 0x048C 0x048F 0x0492 Register Summary - SMT Control Name SMT1TMR SMT1CPR SMT1CPW Bit Pos. 7:0 TMRL[7:0] 15:8 TMRH[7:0] 23:16 TMRU[7:0] 7:0 CPRL[7:0] 15:8 CPRH[7:0] 23:16 CPRU[7:0] 7:0 CPWL[7:0] 15:8 CPWH[7:0] 23:16 CPWU[7:0] 7:0 PRL[7:0] 15:8 PRH[7:0] 0x0495 SMT1PR 0x0498 SMT1CON0 7:0 EN 0x0499 SMT1CON1 7:0 GO REPEAT 0x049A SMT1STAT 7:0 CPRUP CPWUP 0x049B SMT1CLK 7:0 0x049C SMT1SIG 7:0 SSEL[4:0] 0x049D SMT1WIN 7:0 WSEL[4:0] 23:16 37.3 PRU[7:0] STP WPOL SPOL CPOL PS[1:0] MODE[3:0] RST TS WS AS CSEL[2:0] Register Definitions: SMT Control (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 615 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.1 SMTxCON0 Name: Offset: SMTxCON0 0x0498 SMT Control Register 0 Bit 7 Access Reset 5 4 3 2 EN 6 STP WPOL SPOL CPOL 1 0 R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 PS[1:0] Bit 7 - EN SMT Enable Bit Value 1 0 Description SMT is enabled SMT is disabled; internal states are reset, clock requests are disabled Bit 5 - STP SMT Counter Halt Enable bit Value 1 0 Condition Description When SMTxTMR = SMTxPR Counter remains SMTxPR; period match interrupt occurs when clocked When SMTxTMR = SMTxPR Counter resets to 0x000000; period match interrupt occurs when clocked Bit 4 - WPOL SMTxWIN Input Polarity Control bit Value 1 0 Description Window signal is active-low/falling edge enabled Window signal is active-high/rising edge enabled Bit 3 - SPOL SMTxSIG Input Polarity Control bit Value 1 0 Description SMT Signal is active-low/falling edge enabled SMT Signal is active-high/rising edge enabled Bit 2 - CPOL SMT Clock Input Polarity Control bit Value 1 0 Description SMTxTMR increments on the falling edge of the selected clock signal SMTxTMR increments on the rising edge of the selected clock signal Bits 1:0 - PS[1:0] SMT Prescale Select bits Value 11 10 01 00 Description Prescaler = 1:8 Prescaler = 1:4 Prescaler = 1:2 Prescaler = 1:1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 616 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.2 SMTxCON1 Name: Offset: SMTxCON1 0x0499 SMT Control Register 1 Bit Access Reset 7 6 GO REPEAT 5 4 3 R/W R/W R/W 0 0 0 2 1 0 R/W R/W R/W 0 0 0 MODE[3:0] Bit 7 - GO SMT GO Data Acquisition Bit Value 1 0 Description Incrementing, acquiring data is enabled Incrementing, acquiring data is disabled Bit 6 - REPEAT SMT Repeat Acquisition Enable Bit Value 1 0 Description Repeat Data Acquisition mode is enabled Single Acquisition mode is enabled Bits 3:0 - MODE[3:0] SMT Operation Mode Select bits Value 1111 1110 1101 1100 1011 1010 1001 1000 0111 0110 0101 0100 0011 0010 0001 0000 Description Reserved Reserved Reserved Reserved Reserved Windowed counter Gated counter Counter Capture Time of flight Gated windowed measurement Windowed measurement High and low time measurement Period and Duty-Cycle Acquisition Gated Timer Timer (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 617 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.3 SMTxSTAT Name: Offset: SMTxSTAT 0x049A SMT Status Register Bit Access Reset 7 6 2 1 0 CPRUP CPWUP 5 RST 4 3 TS WS AS R/W/HC R/W/HC R/W RO RO RO 0 0 0 0 0 0 Bit 7 - CPRUP SMT Manual Period Buffer Update bit Value 1 0 Description Request update to SMTxCPR registers SMTxCPR registers update is complete Bit 6 - CPWUP SMT Manual Pulse Width Buffer Update bit Value 1 0 Description Request update to SMTxCPW registers SMTxCPW registers update is complete Bit 4 - RST SMT Manual Timer Reset bit Value 1 0 Description Request Reset to SMTxTMR registers SMTxTMR registers update is complete Bit 2 - TS SMT GO Value Status bit Value 1 0 Description SMTxTMR is incrementing SMTxTMR is not incrementing Bit 1 - WS SMT Window Status bit Value 1 0 Description SMT window is open SMT window is closed Bit 0 - AS SMT Signal Value Status bit Value 1 0 Description SMT acquisition is in progress SMT acquisition is not in progress (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 618 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.4 SMTxCLK Name: Offset: SMTxCLK 0x049B SMT Clock Selection Register Bit 7 6 5 4 3 2 1 0 CSEL[2:0] Access Reset R/W R/W R/W 0 0 0 Bits 2:0 - CSEL[2:0] SMT Clock Selection bits Table 37-5. SMT Clock Source Selection CSEL<2:0> Clock Source 111 CLKREF output 110 SOSC 101 MFINTOSC (31.25kHz) 100 MFINTOSC (500kHz) 011 LFINTOSC 010 HFINTOSC 001 FOSC 000 FOSC/4 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 619 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.5 SMTxWIN Name: Offset: SMTxWIN 0x049D SMT Window Input Select Register Bit 7 6 5 4 3 2 1 0 WSEL[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - WSEL[4:0] SMT Window Selection bits Table 37-6. SMT Window Selection WSEL<4:0> SMT1 Window Source 11111-11000 Reserved 10111 NCO1OUT 10110 Reserved 10101 CLKREFOUT 10100 CLC4OUT 10011 CLC3OUT 10010 CLC2OUT 10001 CLC1OUT 10000 ZCDOUT 01111 C2OUT 01110 C1OUT 01101 PWM7OUT 01100 PWM6OUT 01011 CCP4OUT 01010 CCP3OUT 01001 CCP2OUT 01000 CCP1OUT 00111 TMR6_postscaled_out 00110 TMR4_postscaled_out 00101 TMR2_postscaled_out 00100 TMR0_overflow 00011 SOSC (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 620 PIC16(L)F18424/44 (SMT) Signal Measurement Timer WSEL<4:0> SMT1 Window Source 00010 MFINTOSC (31.25kHz) 00001 LFINTOSC (31.25kHz) 00000 Pin Selected by SMT1WINPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 621 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.6 SMTxSIG Name: Offset: SMTxSIG 0x049C SMT Signal Selection bits Bit 7 6 5 4 3 2 1 0 SSEL[4:0] Access Reset R/W R/W R/W R/W R/W 0 0 0 0 0 Bits 4:0 - SSEL[4:0] SMT Signal Selection bits Table 37-7. SMT Signal Selection SSEL<4:0> SMT1 Signal Source 11111-10110 Reserved 10101 CLC4OUT 10100 CLC3OUT 10011 CLC2OUT 10010 CLC1OUT 10001 ZCDOUT 10000 C2OUT 01111 C1OUT 01110 NCO1OUT 01101 PWM7OUT 01100 PWM6OUT 01011 CCP4OUT 01010 CCP3OUT 01001 CCP2OUT 01000 CCP1OUT 00111 TMR6 postscaled output 00110 TMR5 overflow 00101 TMR4 postscaled output 00100 TMR3 overflow 00011 TMR2 postscaled output 00010 TMR1 overflow (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 622 PIC16(L)F18424/44 (SMT) Signal Measurement Timer SSEL<4:0> SMT1 Signal Source 00001 TMR0 overflow 00000 Pin Selected by SMT1SIGPPS (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 623 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.7 SMTxTMR Name: Offset: SMTxTMR 0x048C SMT Timer Register Bit 23 22 21 20 19 18 17 16 TMRU[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 8 TMRH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 0 TMRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 23:16 - TMRU[7:0] Upper byte of the SMT timer register Bits 15:8 - TMRH[7:0] High byte of the SMT timer register Bits 7:0 - TMRL[7:0] Lower byte of the SMT timer register (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 624 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.8 SMTxCPR Name: Offset: SMTxCPR 0x048F SMT Captured Period Register Bit 23 22 21 20 19 18 17 16 CPRU[7:0] Access Reset Bit RO RO RO RO RO RO RO RO x x x x x x x x 15 14 13 12 11 10 9 8 CPRH[7:0] Access RO RO RO RO RO RO RO RO Reset x x x x x x x x Bit 7 6 5 4 3 2 1 0 CPRL[7:0] Access Reset RO RO RO RO RO RO RO RO x x x x x x x x Bits 23:16 - CPRU[7:0] Upper byte of SMT capture period register Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Bits 15:8 - CPRH[7:0] High byte of SMT capture period register Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Bits 7:0 - CPRL[7:0] Lower byte of SMT capture period register Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 625 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.9 SMTxCPW Name: Offset: SMTxCPW 0x0492 SMT Captured Pulse Width Register Bit 23 22 21 20 19 18 17 16 CPWU[7:0] Access Reset Bit RO RO RO RO RO RO RO RO x x x x x x x x 15 14 13 12 11 10 9 8 CPWH[7:0] Access RO RO RO RO RO RO RO RO Reset x x x x x x x x Bit 7 6 5 4 3 2 1 0 CPWL[7:0] Access Reset RO RO RO RO RO RO RO RO x x x x x x x x Bits 23:16 - CPWU[7:0] Upper Byte of the captured pulse width register Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Bits 15:8 - CPWH[7:0] High Byte of the captured pulse width register Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu Bits 7:0 - CPWL[7:0] Lower Byte of the captured pulse width register Reset States: POR/BOR = xxxxxxxx All Other Resets = uuuuuuuu (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 626 PIC16(L)F18424/44 (SMT) Signal Measurement Timer 37.3.10 SMTxPR Name: Offset: SMTxPR 0x0495 SMT Period Register Bit 23 22 21 20 19 18 17 16 PRU[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 1 1 1 1 1 1 1 Bit 15 14 13 12 11 10 9 8 PRH[7:0] Access R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 1 1 1 1 1 1 1 Bit 7 6 5 4 3 2 1 0 PRL[7:0] Access Reset R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Bits 23:16 - PRU[7:0] Upper byte of the SMT period register Bits 15:8 - PRH[7:0] High byte of the SMT period register Bits 7:0 - PRL[7:0] Lower byte of the SMT period register (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 627 PIC16(L)F18424/44 Register Summary 38. Register Summary Offset Name Bit Pos. 0x00 INDF0 7:0 INDF0[7:0] 0x01 INDF1 7:0 INDF1[7:0] 0x02 PCL 7:0 0x03 STATUS 7:0 0x04 FSR0 0x06 FSR1 0x08 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x09 WREG 7:0 0x0A PCLATH 7:0 0x0B INTCON 7:0 0x0C PORTA 7:0 0x0D PORTB 0x0E PORTC Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG RA5 RA4 7:0 RB7 RB6 RB5 RB4 7:0 RC7 RC6 RC5 RC4 RA3 RA2 RA1 RA0 RC3 RC2 RC1 RC0 TRISA2 TRISA1 TRISA0 TRISC2 TRISC1 TRISC0 LATA2 LATA1 LATA0 LATC2 LATC1 LATC0 Z DC C 0x0F ... Reserved 0x11 0x12 TRISA 7:0 TRISA5 TRISA4 0x13 TRISB 7:0 TRISB7 TRISB6 TRISB5 TRISB4 0x14 TRISC 7:0 TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 0x15 ... Reserved 0x17 0x18 LATA 7:0 LATA5 LATA4 0x19 LATB 7:0 LATB7 LATB6 LATB5 LATB4 0x1A LATC 7:0 LATC7 LATC6 LATC5 LATC4 LATC3 0x1B ... Reserved 0x7F 0x80 INDF0 7:0 INDF0[7:0] 0x81 INDF1 7:0 INDF1[7:0] 0x82 PCL 7:0 0x83 STATUS 7:0 0x84 0x86 FSR0 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x88 BSR 7:0 0x89 WREG 7:0 0x8A PCLATH 7:0 0x8B INTCON 7:0 0x8C ADLTH 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE (c) 2018 Microchip Technology Inc. PEIE INTEDG LTHL[7:0] Datasheet Preliminary DS40002000A-page 628 PIC16(L)F18424/44 Register Summary Offset Name 0x8E ADUTH 0x90 ADERR 0x92 ADSTPT 0x94 ADFLTR Bit Pos. 15:8 LTHH[7:0] 7:0 UTHL[7:0] 15:8 UTHH[7:0] 7:0 ADERRL[7:0] 15:8 ERRH[7:0] 7:0 STPTL[7:0] 15:8 STPTH[7:0] 7:0 FLTRL[7:0] 15:8 FLTRH[7:0] 7:0 ACCL[7:0] 15:8 ACCH[7:0] 0x96 ADACC 0x99 ADCNT 7:0 0x9A ADRPT 7:0 RPT[7:0] 7:0 PREVL[7:0] 15:8 PREVH[7:0] 23:16 0x9B ADPREV 0x9D ADRES 0x9F ADPCH ACCU[1:0] CNT[7:0] 7:0 RESL[7:0] 15:8 RESH[7:0] 7:0 PCH[5:0] 0xA0 ... Reserved 0xFF 0x0100 INDF0 7:0 INDF0[7:0] 0x0101 INDF1 7:0 INDF1[7:0] 0x0102 PCL 7:0 PCL[7:0] 0x0103 STATUS 7:0 0x0104 0x0106 FSR0 FSR1 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0108 BSR 7:0 WREG 7:0 0x010A PCLATH 7:0 0x010B INTCON 7:0 ADACQ 0x010E ADCAP PD FSRL[7:0] 0x0109 0x010C TO 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 7:0 ACQL[7:0] 15:8 ACQH[4:0] 7:0 CAP[4:0] 7:0 PREL[7:0] 0x010F ADPRE 0x0111 ADCON0 7:0 ON CONT 0x0112 ADCON1 7:0 PPOL IPEN 0x0113 ADCON2 7:0 PSIS 0x0114 ADCON3 7:0 0x0115 ADSTAT 7:0 0x0116 ADREF 7:0 0x0117 ADACT 7:0 15:8 PREH[4:0] OV (c) 2018 Microchip Technology Inc. UTHR CS FRM GO GPOL DSEN CRS[2:0] ACLR MD[2:0] CALC[2:0] SOI MD[2:0] LTHR MATH STAT[2:0] NREF PREF[1:0] ACT[4:0] Datasheet Preliminary DS40002000A-page 629 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0118 ADCLK 7:0 0x0119 RC1REG 7:0 RCREG[7:0] 0x011A TX1REG 7:0 TXREG[7:0] 0x011B SP1BRG 0x011D RC1STA 7:0 SPEN RX9 SREN CREN ADDEN FERR OERR 0x011E TX1STA 7:0 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0x011F BAUD1CON 7:0 ABDOVF RCIDL SCKP BRG16 WUE ABDEN DC C CS[5:0] 7:0 SPBRGL[7:0] 15:8 SPBRGH[7:0] RX9D 0x0120 ... Reserved 0x017F 0x0180 INDF0 7:0 INDF0[7:0] 0x0181 INDF1 7:0 INDF1[7:0] 0x0182 PCL 7:0 PCL[7:0] 0x0183 STATUS 7:0 0x0184 FSR0 0x0186 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0188 BSR 7:0 0x0189 WREG 7:0 0x018A PCLATH 7:0 Z BSR[5:0] WREG[7:0] PCLATH[6:0] 0x018B INTCON 7:0 0x018C SSP1BUF 7:0 GIE PEIE BUF[7:0] INTEDG 0x018D SSP1ADD 7:0 ADD[7:0] 0x018E SSP1MSK 7:0 0x018F SSP1STAT 7:0 SMP 0x0190 SSP1CON1 7:0 0x0191 SSP1CON2 7:0 0x0192 SSP1CON3 7:0 MSK[6:0] CKE D/A WCOL SSPOV SSPEN CKP GCEN ACKSTAT ACKDT ACKTIM PCIE SCIE MSK0 P S R/W UA BF ACKEN RCEN PEN RSEN SEN BOEN SDAHT SBCDE AHEN DHEN Z DC C SSPM[3:0] 0x0193 ... Reserved 0x01FF 0x0200 INDF0 7:0 INDF0[7:0] 0x0201 INDF1 7:0 INDF1[7:0] 0x0202 PCL 7:0 PCL[7:0] 0x0203 STATUS 7:0 0x0204 FSR0 0x0206 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0208 BSR 7:0 0x0209 WREG 7:0 0x020A PCLATH 7:0 0x020B INTCON 7:0 0x020C TMR1 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE (c) 2018 Microchip Technology Inc. PEIE INTEDG TMRxL[7:0] Datasheet Preliminary DS40002000A-page 630 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x020E T1CON 7:0 0x020F T1GCON 7:0 0x0210 TMR1GATE 7:0 GSS[4:0] 0x0211 TMR1CLK 7:0 CS[4:0] 0x0212 TMR3 0x0214 T3CON 15:8 TMRxH[7:0] CKPS[1:0] GE GPOL GTM SYNC GSPM GGO/DONE 7:0 TMRxL[7:0] 15:8 TMRxH[7:0] 7:0 CKPS[1:0] GE GPOL GTM SYNC GSPM 0x0215 T3GCON 7:0 0x0216 TMR3GATE 7:0 GGO/DONE GSS[4:0] 0x0217 TMR3CLK 7:0 CS[4:0] 0x0218 TMR5 7:0 TMRxL[7:0] 15:8 TMRxH[7:0] 0x021A T5CON 7:0 0x021B T5GCON 7:0 0x021C TMR5GATE 7:0 0x021D TMR5CLK 7:0 0x021E CCPTMRS0 7:0 0x021F CCPTMRS1 7:0 CKPS[1:0] GE GPOL GTM ON RD16 ON RD16 ON GVAL SYNC GSPM RD16 GVAL GGO/DONE GVAL GSS[4:0] CS[4:0] C4TSEL[1:0] C3TSEL[1:0] C2TSEL[1:0] P7TSEL[1:0] P6TSEL[1:0] C1TSEL[1:0] 0x0220 ... Reserved 0x027F 0x0280 INDF0 7:0 INDF0[7:0] 0x0281 INDF1 7:0 INDF1[7:0] 0x0282 PCL 7:0 PCL[7:0] 0x0283 STATUS 7:0 0x0284 0x0286 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0288 BSR 7:0 0x0289 WREG 7:0 0x028A PCLATH 7:0 0x028B INTCON 7:0 0x028C T2TMR 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG TxTMR[7:0] 0x028D T2PR 7:0 0x028E T2CON 7:0 ON TxPR[7:0] 0x028F T2HLT 7:0 PSYNC 0x0290 T2CLKCON 7:0 CS[3:0] 0x0291 T2RST 7:0 RSEL[3:0] 0x0292 T4TMR 7:0 CKPS[2:0] CPOL OUTPS[3:0] CSYNC MODE[4:0] TxTMR[7:0] 0x0293 T4PR 7:0 0x0294 T4CON 7:0 ON TxPR[7:0] PSYNC CKPS[2:0] 0x0295 T4HLT 7:0 0x0296 T4CLKCON 7:0 CS[3:0] 0x0297 T4RST 7:0 RSEL[3:0] (c) 2018 Microchip Technology Inc. CPOL CSYNC OUTPS[3:0] Datasheet Preliminary MODE[4:0] DS40002000A-page 631 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0298 T6TMR 7:0 0x0299 T6PR 7:0 0x029A T6CON 7:0 ON 0x029B T6HLT 7:0 PSYNC 0x029C T6CLKCON 7:0 CS[3:0] 0x029D T6RST 7:0 RSEL[3:0] 0x029E Reserved 0x029F ADCPCON0 7:0 TxTMR[7:0] TxPR[7:0] CKPS[2:0] CPOL OUTPS[3:0] CSYNC MODE[4:0] CPON CPRDY 0x02A0 ... Reserved 0x02FF 0x0300 INDF0 7:0 INDF0[7:0] 0x0301 INDF1 7:0 INDF1[7:0] 0x0302 PCL 7:0 PCL[7:0] 0x0303 STATUS 7:0 0x0304 FSR0 0x0306 FSR1 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0308 BSR 7:0 WREG 7:0 0x030A PCLATH 7:0 0x030B INTCON 7:0 GIE PEIE INTEDG CCPRH[7:0] CCP1CON 7:0 0x030F CCP1CAP 7:0 0x0310 CCPR2 0x0312 CCP2CON 7:0 0x0313 CCP2CAP 7:0 EN OUT FMT MODE[3:0] CTS[2:0] 7:0 CCPRL[7:0] 15:8 CCPRH[7:0] EN OUT FMT MODE[3:0] CTS[2:0] 7:0 CCPRL[7:0] 15:8 CCPRH[7:0] 0x0316 CCP3CON 7:0 0x0317 CCP3CAP 7:0 0x0318 CCPR4 0x031A CCP4CON 7:0 0x031B CCP4CAP 7:0 C PCLATH[6:0] 15:8 0x030E DC BSR[5:0] CCPRL[7:0] CCPR1 Z WREG[7:0] 7:0 0x030C CCPR3 PD FSRL[7:0] 0x0309 0x0314 TO 7:0 EN OUT FMT MODE[3:0] CTS[2:0] 7:0 CCPRL[7:0] 15:8 CCPRH[7:0] EN OUT FMT MODE[3:0] CTS[2:0] 0x031C ... Reserved 0x037F 0x0380 INDF0 7:0 INDF0[7:0] 0x0381 INDF1 7:0 INDF1[7:0] 0x0382 PCL 7:0 0x0383 STATUS 7:0 (c) 2018 Microchip Technology Inc. PCL[7:0] TO PD Datasheet Preliminary Z DC C DS40002000A-page 632 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0384 FSR0 0x0386 FSR1 0x0388 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0389 WREG 7:0 0x038A PCLATH 7:0 0x038B INTCON 7:0 0x038C PWM6DC 0x038E PWM6CON 0x038F Reserved 0x0390 PWM7DC 0x0392 PWM7CON BSR[5:0] WREG[7:0] PCLATH[6:0] GIE 7:0 PEIE INTEDG DCL[1:0] 15:8 7:0 DCH[7:0] EN 7:0 OUT POL OUT POL DCL[1:0] 15:8 7:0 DCH[7:0] EN 0x0393 ... Reserved 0x03FF 0x0400 INDF0 7:0 INDF0[7:0] 0x0401 INDF1 7:0 INDF1[7:0] 0x0402 PCL 7:0 0x0403 STATUS 7:0 0x0404 FSR0 0x0406 FSR1 0x0408 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0409 WREG 7:0 0x040A PCLATH 7:0 0x040B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x040C ... Reserved 0x047F 0x0480 INDF0 7:0 INDF0[7:0] 0x0481 INDF1 7:0 INDF1[7:0] 0x0482 PCL 7:0 PCL[7:0] 0x0483 STATUS 7:0 0x0484 FSR0 0x0486 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0488 BSR 7:0 0x0489 WREG 7:0 0x048A PCLATH 7:0 0x048B INTCON 7:0 0x048C SMT1TMR 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE (c) 2018 Microchip Technology Inc. PEIE INTEDG TMRL[7:0] Datasheet Preliminary DS40002000A-page 633 PIC16(L)F18424/44 Register Summary Offset 0x048F 0x0492 0x0495 Name SMT1CPR SMT1CPW SMT1PR Bit Pos. 15:8 TMRH[7:0] 23:16 TMRU[7:0] 7:0 CPRL[7:0] 15:8 CPRH[7:0] 23:16 CPRU[7:0] 7:0 CPWL[7:0] 15:8 CPWH[7:0] 23:16 CPWU[7:0] 7:0 PRL[7:0] 15:8 PRH[7:0] 23:16 PRU[7:0] 0x0498 SMT1CON0 7:0 EN 0x0499 SMT1CON1 7:0 GO REPEAT STP WPOL SPOL CPOL 0x049A SMT1STAT 7:0 CPRUP CPWUP 0x049B SMT1CLK 7:0 0x049C SMT1SIG 7:0 SSEL[4:0] 0x049D SMT1WIN 7:0 WSEL[4:0] PS[1:0] MODE[3:0] RST TS WS AS CSEL[2:0] 0x049E ... Reserved 0x04FF 0x0500 INDF0 7:0 INDF0[7:0] 0x0501 INDF1 7:0 INDF1[7:0] 0x0502 PCL 7:0 0x0503 STATUS 7:0 0x0504 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0506 FSR1 0x0508 BSR 7:0 0x0509 WREG 7:0 0x050A PCLATH 7:0 0x050B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x050C ... Reserved 0x057F 0x0580 INDF0 7:0 INDF0[7:0] 0x0581 INDF1 7:0 INDF1[7:0] 0x0582 PCL 7:0 0x0583 STATUS 7:0 0x0584 FSR0 0x0586 FSR1 0x0588 BSR 7:0 0x0589 WREG 7:0 0x058A PCLATH 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] (c) 2018 Microchip Technology Inc. Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] Datasheet Preliminary DS40002000A-page 634 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x058B INTCON 7:0 0x058C NCO1ACC GIE PEIE INTEDG 7:0 ACCL[7:0] 15:8 ACCH[7:0] 23:16 0x058F NCO1INC ACCU[3:0] 7:0 INCL[7:0] 15:8 INCH[7:0] 23:16 0x0592 NCO1CON 7:0 0x0593 NCO1CLK 7:0 INCU[3:0] EN OUT POL PFM PWS[2:0] CKS[3:0] 0x0594 ... Reserved 0x059B 0x059C TMR0L 7:0 TMR0L[7:0] 0x059D TMR0H 7:0 TMR0H[7:0] 0x059E T0CON0 7:0 0x059F T0CON1 7:0 T0EN T0OUT T0CS[2:0] T016BIT T0OUTPS[3:0] T0ASYNC T0CKPS[3:0] 0x05A0 ... Reserved 0x05FF 0x0600 INDF0 7:0 INDF0[7:0] 0x0601 INDF1 7:0 INDF1[7:0] 0x0602 PCL 7:0 0x0603 STATUS 7:0 0x0604 FSR0 0x0606 FSR1 0x0608 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0609 WREG 7:0 0x060A PCLATH 7:0 0x060B INTCON 7:0 0x060C CWG1CLK 7:0 0x060D CWG1ISM 7:0 0x060E CWG1DBR 7:0 0x060F CWG1DBF 7:0 0x0610 CWG1CON0 7:0 0x0611 CWG1CON1 7:0 0x0612 CWG1AS0 7:0 0x0613 CWG1AS1 7:0 7:0 0x0614 CWG1STR 0x0615 Reserved 0x0616 CWG2CLK 7:0 0x0617 CWG2ISM 7:0 0x0618 CWG2DBR 7:0 0x0619 CWG2DBF 7:0 0x061A CWG2CON0 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG CS ISM[3:0] DBR[5:0] DBF[5:0] EN LD SHUTDOWN REN MODE[2:0] IN OVRD OVRC POLD LSBD[1:0] POLC POLB POLA LSAC[1:0] AS5E AS4E AS3E AS2E AS1E AS0E OVRB OVRA STRD STRC STRB STRA CS ISM[3:0] DBR[5:0] DBF[5:0] EN (c) 2018 Microchip Technology Inc. LD MODE[2:0] Datasheet Preliminary DS40002000A-page 635 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x061B CWG2CON1 7:0 0x061C CWG2AS0 7:0 0x061D CWG2AS1 7:0 0x061E CWG2STR 7:0 IN SHUTDOWN OVRD REN OVRC POLD LSBD[1:0] POLC POLB POLA LSAC[1:0] AS5E AS4E AS3E AS2E AS1E AS0E OVRB OVRA STRD STRC STRB STRA Z DC C 0x061F ... Reserved 0x067F 0x0680 INDF0 7:0 INDF0[7:0] 0x0681 INDF1 7:0 INDF1[7:0] 0x0682 PCL 7:0 0x0683 STATUS 7:0 0x0684 FSR0 0x0686 FSR1 0x0688 BSR 7:0 0x0689 WREG 7:0 0x068A PCLATH 7:0 0x068B INTCON 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x068C ... Reserved 0x06FF 0x0700 INDF0 7:0 INDF0[7:0] 0x0701 INDF1 7:0 INDF1[7:0] 0x0702 PCL 7:0 PCL[7:0] 0x0703 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0704 FSR0 0x0706 FSR1 0x0708 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0709 WREG 7:0 0x070A PCLATH 7:0 PCLATH[6:0] INTCON 7:0 PIR0 7:0 0x070D PIR1 7:0 0x070E PIR2 7:0 0x070F PIR3 7:0 RC1IF TX1IF 0x0710 PIR4 7:0 TMR6IF TMR5IF CL24IF CLC1IF PIR5 7:0 PIR6 7:0 0x0713 PIR7 7:0 0x0714 PIR8 7:0 0x0715 Reserved 0x0716 PIE0 7:0 0x0717 PIE1 7:0 C WREG[7:0] 0x070B 0x0711 DC BSR[5:0] 0x070C 0x0712 Z GIE PEIE INTEDG TMR0IF OSFIF IOCIF INTF CSWIF ADTIF ZCDIF CLC4IF CLC3IF TMR4IF CCP4IF NVMIF NCO1IF C2IF C1IF BCL1IF SSP1IF TMR3IF TMR2IF TMR1IF TMR5GIF TMR3GIF TMR1GIF CCP3IF CCP2IF CCP1IF CWG2IF CWG1IF SMT1PWAIF SMT1PRAIF TMR0IE OSFIE (c) 2018 Microchip Technology Inc. IOCIE CSWIE SMT1IF INTE ADTIE Datasheet Preliminary ADIF ADIE DS40002000A-page 636 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0718 PIE2 7:0 0x0719 PIE3 7:0 RC1IE TX1IE 0x071A PIE4 7:0 TMR6IE TMR5IE CLC2IE CLC1IE 0x071B PIE5 7:0 0x071C PIE6 7:0 0x071D PIE7 7:0 0x071E PIE8 7:0 ZCDIE CLC4IE CLC3IE TMR4IE CCP4IE NVMIE C2IE C1IE BCL1IE SSP1IE TMR3IE TMR2IE TMR1IE TMR5GIE TMR3GIE TMR1GIE CCP3IE CCP2IE CCP1IE CWG2IE CWG1IE NCO1IE SMT1PWAIE SMT1PRAIE SMT1IE 0x071F ... Reserved 0x077F 0x0780 INDF0 7:0 INDF0[7:0] 0x0781 INDF1 7:0 INDF1[7:0] 0x0782 PCL 7:0 0x0783 STATUS 7:0 0x0784 FSR0 0x0786 FSR1 0x0788 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] 0x0789 WREG 7:0 0x078A PCLATH 7:0 WREG[7:0] 0x078B INTCON 7:0 GIE SYSCMD PCLATH[6:0] PEIE INTEDG 0x078C ... Reserved 0x0795 0x0796 PMD0 7:0 0x0797 PMD1 7:0 0x0798 PMD2 7:0 FVRMD TMR6MD TMR5MD TMR4MD NVMMD CLKRMD IOCMD TMR3MD TMR2MD TMR1MD TMR0MD C2MD C1MD ZCDMD CCP4MD CCP3MD CCP2MD CCP1MD CLC3MD CLC2MD CLC1MD DSM1MD Z DC C NCO1MD 0x0799 PMD3 7:0 DAC1MD ADCMD 0x079A PMD4 7:0 PWM7MD PWM6MD 0x079B PMD5 7:0 CWG2MD CWG1MD 0x079C PMD6 7:0 0x079D PMD7 7:0 UART1MD SMT1MD CLC4MD MSSP1MD 0x079E ... Reserved 0x07FF 0x0800 INDF0 7:0 INDF0[7:0] 0x0801 INDF1 7:0 INDF1[7:0] 0x0802 PCL 7:0 PCL[7:0] 0x0803 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0804 FSR0 0x0806 FSR1 0x0808 BSR 7:0 0x0809 WREG 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] (c) 2018 Microchip Technology Inc. BSR[5:0] WREG[7:0] Datasheet Preliminary DS40002000A-page 637 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x080A PCLATH 7:0 0x080B INTCON 7:0 0x080C WDTCON0 7:0 0x080D WDTCON1 7:0 0x080E WDTPSL 7:0 0x080F WDTPSH 7:0 0x0810 WDTTMR 7:0 0x0811 BORCON 7:0 0x0812 VREGCON 7:0 0x0813 PCON0 7:0 0x0814 PCON1 7:0 PCLATH[6:0] GIE PEIE INTEDG WDTPS[4:0] SEN WDTCS[2:0] WINDOW[2:0] PSCNTL[7:0] PSCNTH[7:0] WDTTMR[4:0] STATE PSCNT[1:0] SBOREN BORRDY VREGPM STKOVF STKUNF WDTWV RWDT RMCLR RI POR BOR MEMV 0x0815 ... Reserved 0x0819 0x081A NVMADR 7:0 NVMADRL[7:0] 15:8 NVMADRH[6:0] 7:0 NVMDATL[7:0] 0x081C NVMDAT 0x081E NVMCON1 7:0 0x081F NVMCON2 7:0 NVMCON2[7:0] 15:8 NVMDATH[5:0] NVMREGS LWLO FREE WRERR WREN WR RD Z DC C 0x0820 ... Reserved 0x087F 0x0880 INDF0 7:0 INDF0[7:0] 0x0881 INDF1 7:0 INDF1[7:0] 0x0882 PCL 7:0 0x0883 STATUS 7:0 0x0884 0x0886 FSR0 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0888 BSR 7:0 0x0889 WREG 7:0 0x088A PCLATH 7:0 0x088B INTCON 7:0 GIE PEIE 0x088C CPUDOZE 7:0 IDLEN DOZEN 0x088D OSCCON1 7:0 NOSC[2:0] 0x088E OSCCON2 7:0 COSC[2:0] 0x088F OSCCON3 7:0 0x0890 OSCSTAT 7:0 EXTOR HFOR MFOR LFOR SOR ADOR 0x0891 OSCEN 7:0 EXTOEN HFOEN MFOEN LFOEN SOSCEN ADOEN 0x0892 OSCTUNE 7:0 0x0893 OSCFRQ 7:0 0x0894 Reserved 0x0895 CLKRCON 7:0 0x0896 CLKRCLK 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] CSWHOLD INTEDG ROI SOSCPWR DOE DOZE[2:0] NDIV[3:0] CDIV[3:0] ORDY NOSCR PLLR HFTUN[5:0] HFFRQ[2:0] EN (c) 2018 Microchip Technology Inc. DC[1:0] DIV[2:0] CLK[3:0] Datasheet Preliminary DS40002000A-page 638 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0897 MD1CON0 7:0 0x0898 MD1CON1 7:0 0x0899 MD1SRC 7:0 0x089A MD1CARL 7:0 CLS[3:0] 0x089B MD1CARH 7:0 CHS[3:0] EN OUT OPOL CHPOL CHSYNC BIT CLPOL CLSYNC SRCS[4:0] 0x089C ... Reserved 0x08FF 0x0900 INDF0 7:0 INDF0[7:0] 0x0901 INDF1 7:0 INDF1[7:0] 0x0902 PCL 7:0 PCL[7:0] 0x0903 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0904 FSR0 0x0906 FSR1 0x0908 BSR 7:0 0x0909 WREG 7:0 0x090A PCLATH 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] 0x090B INTCON 7:0 GIE PEIE 0x090C FVRCON 7:0 FVREN FVRRDY 0x090D Reserved 0x090E DAC1CON0 7:0 EN 0x090F DAC1CON1 7:0 INTEDG TSEN TSRNG CDAFVR[1:0] OE1 ADFVR[1:0] PSS[1:0] NSS DAC1R[4:0] 0x0910 ... Reserved 0x091E 0x091F ZCDCON 7:0 SEN OUT POL INTP INTN DC C 0x0920 ... Reserved 0x097F 0x0980 INDF0 7:0 INDF0[7:0] 0x0981 INDF1 7:0 INDF1[7:0] 0x0982 PCL 7:0 PCL[7:0] 0x0983 STATUS 7:0 0x0984 FSR0 0x0986 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0988 BSR 7:0 0x0989 WREG 7:0 0x098A PCLATH 7:0 0x098B INTCON 7:0 Z BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x098C ... Reserved 0x098E (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 639 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x098F CMOUT 7:0 0x0990 CM1CON0 7:0 0x0991 CM1CON1 0x0992 0x0993 MC2OUT MC1OUT HYS SYNC 7:0 INTP INTN CM1NCH 7:0 NCH[2:0] CM1PCH 7:0 PCH[2:0] 0x0994 CM2CON0 7:0 HYS SYNC 0x0995 CM2CON1 7:0 INTP INTN 0x0996 CM2NCH 7:0 NCH[2:0] 0x0997 CM2PCH 7:0 PCH[2:0] EN EN OUT OUT POL POL 0x0998 ... Reserved 0x09FF 0x0A00 INDF0 7:0 INDF0[7:0] 0x0A01 INDF1 7:0 INDF1[7:0] 0x0A02 PCL 7:0 0x0A03 STATUS 7:0 0x0A04 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0A06 FSR1 0x0A08 BSR 7:0 0x0A09 WREG 7:0 0x0A0A PCLATH 7:0 0x0A0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0A0C ... Reserved 0x0A7F 0x0A80 INDF0 7:0 INDF0[7:0] 0x0A81 INDF1 7:0 INDF1[7:0] 0x0A82 PCL 7:0 0x0A83 STATUS 7:0 0x0A84 FSR0 0x0A86 FSR1 0x0A88 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0A89 WREG 7:0 0x0A8A PCLATH 7:0 0x0A8B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0A8C ... Reserved 0x0AFF 0x0B00 INDF0 7:0 INDF0[7:0] 0x0B01 INDF1 7:0 INDF1[7:0] 0x0B02 PCL 7:0 PCL[7:0] 0x0B03 STATUS 7:0 (c) 2018 Microchip Technology Inc. TO PD Datasheet Preliminary Z DC C DS40002000A-page 640 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0B04 FSR0 0x0B06 FSR1 0x0B08 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0B09 WREG 7:0 0x0B0A PCLATH 7:0 0x0B0B INTCON 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0B0C ... Reserved 0x0B7F 0x0B80 INDF0 7:0 INDF0[7:0] 0x0B81 INDF1 7:0 INDF1[7:0] 0x0B82 PCL 7:0 PCL[7:0] 0x0B83 STATUS 7:0 0x0B84 FSR0 0x0B86 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0B88 BSR 7:0 0x0B89 WREG 7:0 0x0B8A PCLATH 7:0 0x0B8B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0B8C ... Reserved 0x0BFF 0x0C00 INDF0 7:0 INDF0[7:0] 0x0C01 INDF1 7:0 INDF1[7:0] 0x0C02 PCL 7:0 0x0C03 STATUS 7:0 0x0C04 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0C06 FSR1 0x0C08 BSR 7:0 0x0C09 WREG 7:0 0x0C0A PCLATH 7:0 0x0C0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0C0C ... Reserved 0x0C7F 0x0C80 INDF0 7:0 INDF0[7:0] 0x0C81 INDF1 7:0 INDF1[7:0] 0x0C82 PCL 7:0 0x0C83 STATUS 7:0 0x0C84 FSR0 7:0 (c) 2018 Microchip Technology Inc. PCL[7:0] TO PD Z DC C FSRL[7:0] Datasheet Preliminary DS40002000A-page 641 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 15:8 0x0C86 FSR1 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0C88 BSR 7:0 0x0C89 WREG 7:0 0x0C8A PCLATH 7:0 0x0C8B INTCON 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0C8C ... Reserved 0x0CFF 0x0D00 INDF0 7:0 INDF0[7:0] 0x0D01 INDF1 7:0 INDF1[7:0] 0x0D02 PCL 7:0 0x0D03 STATUS 7:0 0x0D04 FSR0 0x0D06 FSR1 0x0D08 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0D09 WREG 7:0 0x0D0A PCLATH 7:0 0x0D0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0D0C ... Reserved 0x0D7F 0x0D80 INDF0 7:0 INDF0[7:0] 0x0D81 INDF1 7:0 INDF1[7:0] 0x0D82 PCL 7:0 PCL[7:0] 0x0D83 STATUS 7:0 0x0D84 FSR0 0x0D86 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0D88 BSR 7:0 0x0D89 WREG 7:0 0x0D8A PCLATH 7:0 0x0D8B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0D8C ... Reserved 0x0DFF 0x0E00 INDF0 7:0 INDF0[7:0] 0x0E01 INDF1 7:0 INDF1[7:0] 0x0E02 PCL 7:0 0x0E03 STATUS 7:0 0x0E04 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] (c) 2018 Microchip Technology Inc. Datasheet Preliminary Z DC C DS40002000A-page 642 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0E06 FSR1 0x0E08 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0E09 WREG 7:0 0x0E0A PCLATH 7:0 0x0E0B INTCON 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0E0C ... Reserved 0x0E7F 0x0E80 INDF0 7:0 INDF0[7:0] 0x0E81 INDF1 7:0 INDF1[7:0] 0x0E82 PCL 7:0 0x0E83 STATUS 7:0 0x0E84 0x0E86 FSR0 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0E88 BSR 7:0 0x0E89 WREG 7:0 0x0E8A PCLATH 7:0 0x0E8B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0E8C ... Reserved 0x0EFF 0x0F00 INDF0 7:0 INDF0[7:0] 0x0F01 INDF1 7:0 INDF1[7:0] 0x0F02 PCL 7:0 0x0F03 STATUS 7:0 0x0F04 FSR0 0x0F06 FSR1 0x0F08 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x0F09 WREG 7:0 0x0F0A PCLATH 7:0 0x0F0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0F0C ... Reserved 0x0F7F 0x0F80 INDF0 7:0 INDF0[7:0] 0x0F81 INDF1 7:0 INDF1[7:0] 0x0F82 PCL 7:0 PCL[7:0] 0x0F83 STATUS 7:0 0x0F84 FSR0 0x0F86 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] (c) 2018 Microchip Technology Inc. Datasheet Preliminary Z DC C DS40002000A-page 643 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x0F88 BSR 7:0 0x0F89 WREG 7:0 0x0F8A PCLATH 7:0 0x0F8B INTCON 7:0 15:8 FSRH[7:0] BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x0F8C ... Reserved 0x0FFF 0x1000 INDF0 7:0 INDF0[7:0] 0x1001 INDF1 7:0 INDF1[7:0] 0x1002 PCL 7:0 PCL[7:0] 0x1003 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1004 FSR0 0x1006 FSR1 0x1008 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1009 WREG 7:0 0x100A PCLATH 7:0 0x100B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x100C ... Reserved 0x107F 0x1080 INDF0 7:0 INDF0[7:0] 0x1081 INDF1 7:0 INDF1[7:0] 0x1082 PCL 7:0 0x1083 STATUS 7:0 0x1084 0x1086 FSR0 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1088 BSR 7:0 0x1089 WREG 7:0 0x108A PCLATH 7:0 0x108B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x108C ... Reserved 0x10FF 0x1100 INDF0 7:0 INDF0[7:0] 0x1101 INDF1 7:0 INDF1[7:0] 0x1102 PCL 7:0 0x1103 STATUS 7:0 0x1104 FSR0 0x1106 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] (c) 2018 Microchip Technology Inc. Datasheet Preliminary Z DC C DS40002000A-page 644 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1108 BSR 7:0 0x1109 WREG 7:0 0x110A PCLATH 7:0 0x110B INTCON 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x110C ... Reserved 0x117F 0x1180 INDF0 7:0 INDF0[7:0] 0x1181 INDF1 7:0 INDF1[7:0] 0x1182 PCL 7:0 0x1183 STATUS 7:0 0x1184 FSR0 0x1186 FSR1 0x1188 BSR 7:0 0x1189 WREG 7:0 0x118A PCLATH 7:0 0x118B INTCON 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x118C ... Reserved 0x11FF 0x1200 INDF0 7:0 INDF0[7:0] 0x1201 INDF1 7:0 INDF1[7:0] 0x1202 PCL 7:0 PCL[7:0] 0x1203 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1204 FSR0 0x1206 FSR1 0x1208 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1209 WREG 7:0 0x120A PCLATH 7:0 0x120B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x120C ... Reserved 0x127F 0x1280 INDF0 7:0 INDF0[7:0] 0x1281 INDF1 7:0 INDF1[7:0] 0x1282 PCL 7:0 0x1283 STATUS 7:0 0x1284 FSR0 0x1286 FSR1 0x1288 BSR PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 (c) 2018 Microchip Technology Inc. Z DC C BSR[5:0] Datasheet Preliminary DS40002000A-page 645 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1289 WREG 7:0 0x128A PCLATH 7:0 0x128B INTCON 7:0 WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x128C ... Reserved 0x12FF 0x1300 INDF0 7:0 INDF0[7:0] 0x1301 INDF1 7:0 INDF1[7:0] 0x1302 PCL 7:0 PCL[7:0] 0x1303 STATUS 7:0 0x1304 0x1306 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1308 BSR 7:0 0x1309 WREG 7:0 0x130A PCLATH 7:0 0x130B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x130C ... Reserved 0x137F 0x1380 INDF0 7:0 INDF0[7:0] 0x1381 INDF1 7:0 INDF1[7:0] 0x1382 PCL 7:0 0x1383 STATUS 7:0 0x1384 FSR0 0x1386 FSR1 0x1388 BSR 7:0 0x1389 WREG 7:0 0x138A PCLATH 7:0 0x138B INTCON 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x138C ... Reserved 0x13FF 0x1400 INDF0 7:0 INDF0[7:0] 0x1401 INDF1 7:0 INDF1[7:0] 0x1402 PCL 7:0 PCL[7:0] 0x1403 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1404 FSR0 0x1406 FSR1 0x1408 BSR 7:0 0x1409 WREG 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] (c) 2018 Microchip Technology Inc. Z DC C BSR[5:0] WREG[7:0] Datasheet Preliminary DS40002000A-page 646 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x140A PCLATH 7:0 0x140B INTCON 7:0 PCLATH[6:0] GIE PEIE INTEDG 0x140C ... Reserved 0x147F 0x1480 INDF0 7:0 INDF0[7:0] 0x1481 INDF1 7:0 INDF1[7:0] 0x1482 PCL 7:0 0x1483 STATUS 7:0 0x1484 FSR0 0x1486 FSR1 0x1488 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1489 WREG 7:0 0x148A PCLATH 7:0 0x148B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x148C ... Reserved 0x14FF 0x1500 INDF0 7:0 INDF0[7:0] 0x1501 INDF1 7:0 INDF1[7:0] 0x1502 PCL 7:0 PCL[7:0] 0x1503 STATUS 7:0 0x1504 0x1506 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1508 BSR 7:0 0x1509 WREG 7:0 0x150A PCLATH 7:0 0x150B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x150C ... Reserved 0x157F 0x1580 INDF0 7:0 INDF0[7:0] 0x1581 INDF1 7:0 INDF1[7:0] 0x1582 PCL 7:0 0x1583 STATUS 7:0 0x1584 FSR0 0x1586 FSR1 0x1588 BSR 7:0 0x1589 WREG 7:0 0x158A PCLATH 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] (c) 2018 Microchip Technology Inc. Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] Datasheet Preliminary DS40002000A-page 647 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x158B INTCON 7:0 GIE PEIE INTEDG 0x158C ... Reserved 0x15FF 0x1600 INDF0 7:0 INDF0[7:0] 0x1601 INDF1 7:0 INDF1[7:0] 0x1602 PCL 7:0 0x1603 STATUS 7:0 0x1604 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1606 FSR1 0x1608 BSR 7:0 0x1609 WREG 7:0 0x160A PCLATH 7:0 0x160B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x160C ... Reserved 0x167F 0x1680 INDF0 7:0 INDF0[7:0] 0x1681 INDF1 7:0 INDF1[7:0] 0x1682 PCL 7:0 0x1683 STATUS 7:0 0x1684 FSR0 0x1686 FSR1 0x1688 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1689 WREG 7:0 0x168A PCLATH 7:0 0x168B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x168C ... Reserved 0x16FF 0x1700 INDF0 7:0 INDF0[7:0] 0x1701 INDF1 7:0 INDF1[7:0] 0x1702 PCL 7:0 PCL[7:0] 0x1703 STATUS 7:0 0x1704 0x1706 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1708 BSR 7:0 0x1709 WREG 7:0 0x170A PCLATH 7:0 0x170B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE (c) 2018 Microchip Technology Inc. PEIE INTEDG Datasheet Preliminary DS40002000A-page 648 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x170C ... Reserved 0x177F 0x1780 INDF0 7:0 INDF0[7:0] 0x1781 INDF1 7:0 INDF1[7:0] 0x1782 PCL 7:0 PCL[7:0] 0x1783 STATUS 7:0 0x1784 FSR0 0x1786 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1788 BSR 7:0 0x1789 WREG 7:0 0x178A PCLATH 7:0 0x178B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x178C ... Reserved 0x17FF 0x1800 INDF0 7:0 INDF0[7:0] 0x1801 INDF1 7:0 INDF1[7:0] 0x1802 PCL 7:0 0x1803 STATUS 7:0 0x1804 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1806 FSR1 0x1808 BSR 7:0 0x1809 WREG 7:0 0x180A PCLATH 7:0 0x180B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x180C ... Reserved 0x187F 0x1880 INDF0 7:0 INDF0[7:0] 0x1881 INDF1 7:0 INDF1[7:0] 0x1882 PCL 7:0 0x1883 STATUS 7:0 0x1884 FSR0 0x1886 FSR1 0x1888 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1889 WREG 7:0 0x188A PCLATH 7:0 0x188B INTCON 7:0 0x188C Reserved Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE (c) 2018 Microchip Technology Inc. PEIE INTEDG Datasheet Preliminary DS40002000A-page 649 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1900 INDF0 7:0 INDF0[7:0] 0x1901 INDF1 7:0 INDF1[7:0] 0x1902 PCL 7:0 0x1903 STATUS 7:0 0x1904 FSR0 0x1906 FSR1 0x1908 BSR 7:0 ... 0x18FF PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1909 WREG 7:0 0x190A PCLATH 7:0 0x190B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x190C ... Reserved 0x197F 0x1980 INDF0 7:0 INDF0[7:0] 0x1981 INDF1 7:0 INDF1[7:0] 0x1982 PCL 7:0 PCL[7:0] 0x1983 STATUS 7:0 0x1984 0x1986 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1988 BSR 7:0 0x1989 WREG 7:0 0x198A PCLATH 7:0 0x198B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x198C ... Reserved 0x19FF 0x1A00 INDF0 7:0 INDF0[7:0] 0x1A01 INDF1 7:0 INDF1[7:0] 0x1A02 PCL 7:0 0x1A03 STATUS 7:0 0x1A04 FSR0 0x1A06 FSR1 0x1A08 BSR 7:0 0x1A09 WREG 7:0 0x1A0A PCLATH 7:0 0x1A0B INTCON 7:0 0x1A0C ... PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG Reserved (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 650 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1A80 INDF0 7:0 INDF0[7:0] 0x1A81 INDF1 7:0 INDF1[7:0] 0x1A82 PCL 7:0 0x1A83 STATUS 7:0 0x1A84 FSR0 0x1A86 FSR1 0x1A88 BSR 7:0 0x1A89 WREG 7:0 0x1A8A PCLATH 7:0 0x1A8B INTCON 7:0 0x1A7F PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1A8C ... Reserved 0x1AFF 0x1B00 INDF0 7:0 INDF0[7:0] 0x1B01 INDF1 7:0 INDF1[7:0] 0x1B02 PCL 7:0 PCL[7:0] 0x1B03 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1B04 FSR0 0x1B06 FSR1 0x1B08 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1B09 WREG 7:0 0x1B0A PCLATH 7:0 0x1B0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1B0C ... Reserved 0x1B7F 0x1B80 INDF0 7:0 INDF0[7:0] 0x1B81 INDF1 7:0 INDF1[7:0] 0x1B82 PCL 7:0 0x1B83 STATUS 7:0 0x1B84 0x1B86 FSR0 FSR1 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1B88 BSR 7:0 0x1B89 WREG 7:0 0x1B8A PCLATH 7:0 0x1B8B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1B8C ... Reserved 0x1BFF (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 651 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1C00 INDF0 7:0 INDF0[7:0] 0x1C01 INDF1 7:0 INDF1[7:0] 0x1C02 PCL 7:0 PCL[7:0] 0x1C03 STATUS 7:0 0x1C04 0x1C06 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1C08 BSR 7:0 0x1C09 WREG 7:0 0x1C0A PCLATH 7:0 0x1C0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1C0C ... Reserved 0x1C7F 0x1C80 INDF0 7:0 INDF0[7:0] 0x1C81 INDF1 7:0 INDF1[7:0] 0x1C82 PCL 7:0 0x1C83 STATUS 7:0 0x1C84 FSR0 0x1C86 FSR1 0x1C88 BSR 7:0 0x1C89 WREG 7:0 0x1C8A PCLATH 7:0 0x1C8B INTCON 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1C8C ... Reserved 0x1CFF 0x1D00 INDF0 7:0 INDF0[7:0] 0x1D01 INDF1 7:0 INDF1[7:0] 0x1D02 PCL 7:0 PCL[7:0] 0x1D03 STATUS 7:0 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1D04 FSR0 0x1D06 FSR1 0x1D08 BSR 7:0 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1D09 WREG 7:0 0x1D0A PCLATH 7:0 0x1D0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1D0C ... Reserved 0x1D7F 0x1D80 INDF0 7:0 (c) 2018 Microchip Technology Inc. INDF0[7:0] Datasheet Preliminary DS40002000A-page 652 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1D81 INDF1 7:0 0x1D82 PCL 7:0 0x1D83 STATUS 7:0 0x1D84 FSR0 0x1D86 FSR1 0x1D88 BSR 7:0 INDF1[7:0] PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1D89 WREG 7:0 0x1D8A PCLATH 7:0 0x1D8B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1D8C ... Reserved 0x1DFF 0x1E00 INDF0 7:0 INDF0[7:0] 0x1E01 INDF1 7:0 INDF1[7:0] 0x1E02 PCL 7:0 PCL[7:0] 0x1E03 STATUS 7:0 0x1E04 0x1E06 FSR0 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1E08 BSR 7:0 0x1E09 WREG 7:0 0x1E0A PCLATH 7:0 0x1E0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1E0C ... Reserved 0x1E0E 0x1E0F CLCDATA 7:0 0x1E10 CLC1CON 7:0 EN MLC4OUT POL OUT INTP MLC3OUT INTN 0x1E11 CLC1POL 7:0 0x1E12 CLC1SEL0 7:0 D1S[5:0] 0x1E13 CLC1SEL1 7:0 D2S[5:0] 0x1E14 CLC1SEL2 7:0 D3S[5:0] 0x1E15 CLC1SEL3 7:0 D4S[5:0] 0x1E16 CLC1GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T 0x1E17 CLC1GLS1 7:0 G2D4T G2D4N G2D3T G2D3N G2D2T 0x1E18 CLC1GLS2 7:0 G3D4T G3D4N G3D3T G3D3N 0x1E19 CLC1GLS3 7:0 G4D4T G4D4N G4D3T 0x1E1A CLC2CON 7:0 EN OUT G4POL G3POL MLC1OUT G2POL G1POL G1D2N G1D1T G1D1N G2D2N G2D1T G2D1N G3D2T G3D2N G3D1T G3D1N G4D3N G4D2T G4D2N G4D1T G4D1N INTP INTN POL MODE[2:0] 0x1E1B CLC2POL 7:0 0x1E1C CLC2SEL0 7:0 D1S[5:0] 0x1E1D CLC2SEL1 7:0 D2S[5:0] 0x1E1E CLC2SEL2 7:0 D3S[5:0] 0x1E1F CLC2SEL3 7:0 D4S[5:0] (c) 2018 Microchip Technology Inc. MLC2OUT MODE[2:0] G4POL Datasheet Preliminary G3POL G2POL G1POL DS40002000A-page 653 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1E20 CLC2GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T G1D2N G1D1T G1D1N 0x1E21 CLC2GLS1 7:0 G2D4T G2D4N G2D3T G2D3N G2D2T G2D2N G2D1T G2D1N 0x1E22 CLC2GLS2 7:0 G3D4T G3D4N G3D3T G3D3N G3D2T G3D2N G3D1T G3D1N 0x1E23 CLC2GLS3 7:0 G4D4T G4D4N G4D3T G4D3N G4D2T G4D2N G4D1T G4D1N 0x1E24 CLC3CON 7:0 EN OUT INTP INTN 0x1E25 CLC3POL 7:0 POL 0x1E26 CLC3SEL0 7:0 D1S[5:0] 0x1E27 CLC3SEL1 7:0 D2S[5:0] 0x1E28 CLC3SEL2 7:0 D3S[5:0] 0x1E29 CLC3SEL3 7:0 0x1E2A CLC3GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T MODE[2:0] G4POL G3POL G2POL G1POL G1D2N G1D1T G1D1N D4S[5:0] 0x1E2B CLC3GLS1 7:0 G2D4T G2D4N G2D3T G2D3N G2D2T G2D2N G2D1T G2D1N 0x1E2C CLC3GLS2 7:0 G3D4T G3D4N G3D3T G3D3N G3D2T G3D2N G3D1T G3D1N 0x1E2D CLC3GLS3 7:0 G4D4T G4D4N G4D3T G4D3N G4D2T G4D2N G4D1T G4D1N 0x1E2E CLC4CON 7:0 EN OUT INTP INTN 0x1E2F CLC4POL 7:0 POL 0x1E30 CLC4SEL0 7:0 D1S[5:0] 0x1E31 CLC4SEL1 7:0 D2S[5:0] 0x1E32 CLC4SEL2 7:0 D3S[5:0] 0x1E33 CLC4SEL3 7:0 0x1E34 CLC4GLS0 7:0 G1D4T G1D4N G1D3T G1D3N G1D2T 0x1E35 CLC4GLS1 7:0 G2D4T G2D4N G2D3T G2D3N 0x1E36 CLC4GLS2 7:0 G3D4T G3D4N G3D3T G3D3N 0x1E37 CLC4GLS3 7:0 G4D4T G4D4N G4D3T G4D3N MODE[2:0] G4POL G3POL G2POL G1POL G1D2N G1D1T G1D1N G2D2T G2D2N G2D1T G2D1N G3D2T G3D2N G3D1T G3D1N G4D2T G4D2N G4D1T G4D1N Z DC C D4S[5:0] 0x1E38 ... Reserved 0x1E7F 0x1E80 INDF0 7:0 INDF0[7:0] 0x1E81 INDF1 7:0 INDF1[7:0] 0x1E82 PCL 7:0 PCL[7:0] 0x1E83 STATUS 7:0 0x1E84 FSR0 0x1E86 FSR1 TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1E88 BSR 7:0 0x1E89 WREG 7:0 0x1E8A PCLATH 7:0 0x1E8B INTCON 7:0 BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1E8C ... Reserved 0x1E8E 0x1E8F PPSLOCK 7:0 0x1E90 INTPPS 7:0 PORT[1:0] PIN[2:0] 0x1E91 T0CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E92 T1CKIPPS 7:0 PORT[1:0] PIN[2:0] (c) 2018 Microchip Technology Inc. PPSLOCKED Datasheet Preliminary DS40002000A-page 654 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1E93 T1GPPS 7:0 PORT[1:0] PIN[2:0] 0x1E94 T3CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E95 T3GPPS 7:0 PORT[1:0] PIN[2:0] 0x1E96 T5CKIPPS 7:0 PORT[1:0] PIN[2:0] 0x1E97 T5GPPS 7:0 PORT[1:0] PIN[2:0] 0x1E98 ... Reserved 0x1E9B 0x1E9C T2INPPS 7:0 PORT[1:0] PIN[2:0] 0x1E9D T4INPPS 7:0 PORT[1:0] PIN[2:0] 0x1E9E T6INPPS 7:0 PORT[1:0] PIN[2:0] 0x1E9F ... Reserved 0x1EA0 0x1EA1 CCP1PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA2 CCP2PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA3 CCP3PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA4 CCP4PPS 7:0 PORT[1:0] PIN[2:0] 0x1EA5 ... Reserved 0x1EA8 0x1EA9 SMT1WINPPS 7:0 PORT[1:0] PIN[2:0] 0x1EAA SMT1SIGPPS 7:0 PORT[1:0] PIN[2:0] 0x1EAB ... Reserved 0x1EB0 0x1EB1 CWG1PPS 7:0 PORT[1:0] PIN[2:0] 0x1EB2 CWG2PPS 7:0 PORT[1:0] PIN[2:0] 0x1EB3 ... Reserved 0x1EB7 0x1EB8 MDCARLPPS 7:0 PORT[1:0] PIN[2:0] 0x1EB9 MDCARHPPS 7:0 PORT[1:0] PIN[2:0] 0x1EBA MDSRCPPS 7:0 PORT[1:0] PIN[2:0] 0x1EBB CLCIN0PPS 7:0 PORT[1:0] PIN[2:0] 0x1EBC CLCIN1PPS 7:0 PORT[1:0] PIN[2:0] 0x1EBD CLCIN2PPS 7:0 PORT[1:0] PIN[2:0] 0x1EBE CLCIN3PPS 7:0 PORT[1:0] PIN[2:0] 7:0 PORT[1:0] PIN[2:0] 0x1EBF ... Reserved 0x1EC2 0x1EC3 ADACTPPS 0x1EC4 Reserved 0x1EC5 SSP1CLKPPS 7:0 PORT[1:0] PIN[2:0] 0x1EC6 SSP1DATPPS 7:0 PORT[1:0] PIN[2:0] 0x1EC7 SSP1SSPPS 7:0 PORT[1:0] PIN[2:0] 0x1EC8 Reserved (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 655 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1ECB RX1PPS 7:0 PORT[1:0] PIN[2:0] 0x1ECC CK1PPS 7:0 PORT[1:0] PIN[2:0] ... 0x1ECA 0x1ECD ... Reserved 0x1EFF 0x1F00 INDF0 7:0 INDF0[7:0] 0x1F01 INDF1 7:0 INDF1[7:0] 0x1F02 PCL 7:0 0x1F03 STATUS 7:0 0x1F04 FSR0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1F06 FSR1 0x1F08 BSR 7:0 0x1F09 WREG 7:0 0x1F0A PCLATH 7:0 0x1F0B INTCON 7:0 Z DC C BSR[5:0] WREG[7:0] PCLATH[6:0] GIE PEIE INTEDG 0x1F0C ... Reserved 0x1F0F 0x1F10 RA0PPS 7:0 PPS[5:0] 0x1F11 RA1PPS 7:0 PPS[5:0] 0x1F12 RA2PPS 7:0 PPS[5:0] 0x1F13 Reserved 0x1F14 RA4PPS 7:0 PPS[5:0] 0x1F15 RA5PPS 7:0 PPS[5:0] 0x1F16 ... Reserved 0x1F1B 0x1F1C RB4PPS 7:0 PPS[5:0] 0x1F1D RB5PPS 7:0 PPS[5:0] 0x1F1E RB6PPS 7:0 PPS[5:0] 0x1F1F RB7PPS 7:0 PPS[5:0] 0x1F20 RC0PPS 7:0 PPS[5:0] 0x1F21 RC1PPS 7:0 PPS[5:0] 0x1F22 RC2PPS 7:0 PPS[5:0] 0x1F23 RC3PPS 7:0 PPS[5:0] 0x1F24 RC4PPS 7:0 PPS[5:0] 0x1F25 RC5PPS 7:0 PPS[5:0] 0x1F26 RC6PPS 7:0 PPS[5:0] 0x1F27 RC7PPS 7:0 PPS[5:0] 0x1F28 ... Reserved 0x1F37 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 656 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1F38 ANSELA 7:0 ANSELA5 ANSELA4 0x1F39 WPUA 7:0 WPUA5 WPUA4 0x1F3A ODCONA 7:0 ODCA5 ODCA4 0x1F3B SLRCONA 7:0 SLRA5 SLRA4 0x1F3C INLVLA 7:0 INLVLA5 INLVLA4 0x1F3D IOCAP 7:0 IOCAP5 IOCAP4 IOCAP3 IOCAP2 IOCAP1 IOCAP0 0x1F3E IOCAN 7:0 IOCAN5 IOCAN4 IOCAN3 IOCAN2 IOCAN1 IOCAN0 0x1F3F IOCAF 7:0 IOCAF5 IOCAF4 IOCAF3 IOCAF2 IOCAF1 IOCAF0 WPUA3 INLVLA3 ANSELA2 ANSELA1 ANSELA0 WPUA2 WPUA1 WPUA0 ODCA2 ODCA1 ODCA0 SLRA2 SLRA1 SLRA0 INLVLA2 INLVLA1 INLVLA0 0x1F40 ... Reserved 0x1F42 0x1F43 ANSELB 7:0 ANSELB7 ANSELB6 ANSELB5 ANSELB4 0x1F44 WPUB 7:0 WPUB7 WPUB6 WPUB5 WPUB4 0x1F45 ODCONB 7:0 ODCB7 ODCB6 ODCB5 ODCB4 0x1F46 SLRCONB 7:0 SLRB7 SLRB6 SLRB5 SLRB4 0x1F47 INLVLB 7:0 INLVLB7 INLVLB6 INLVLB5 INLVLB4 0x1F48 IOCBP 7:0 IOCBP7 IOCBP6 IOCBP5 IOCBP4 0x1F49 IOCBN 7:0 IOCBN7 IOCBN6 IOCBN5 IOCBN4 0x1F4A IOCBF 7:0 IOCBF7 IOCBF6 IOCBF5 IOCBF4 ANSELC 7:0 ANSELC7 ANSELC6 ANSELC5 ANSELC4 ANSELC3 ANSELC2 ANSELC1 ANSELC0 0x1F4F WPUC 7:0 WPUC7 WPUC6 WPUC5 WPUC4 WPUC3 WPUC2 WPUC1 WPUC0 0x1F50 ODCONC 7:0 ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 ODCC2 ODCC1 ODCC0 0x1F51 SLRCONC 7:0 SLRC7 SLRC6 SLRC5 SLRC4 SLRC3 SLRC2 SLRC1 SLRC0 0x1F52 INLVLC 7:0 INLVLC7 INLVLC6 INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 0x1F53 IOCCP 7:0 IOCCP7 IOCCP6 IOCCP5 IOCCP4 IOCCP3 IOCCP2 IOCCP1 IOCCP0 0x1F54 IOCCN 7:0 IOCCN7 IOCCN6 IOCCN5 IOCCN4 IOCCN3 IOCCN2 IOCCN1 IOCCN0 0x1F55 IOCCF 7:0 IOCCF7 IOCCF6 IOCCF5 IOCCF4 IOCCF3 IOCCF2 IOCCF1 IOCCF0 Z DC C 0x1F4B ... Reserved 0x1F4D 0x1F4E 0x1F56 ... Reserved 0x1F7F 0x1F80 INDF0 7:0 INDF0[7:0] 0x1F81 INDF1 7:0 INDF1[7:0] 0x1F82 PCL 7:0 0x1F83 STATUS 7:0 0x1F84 FSR0 0x1F86 FSR1 0x1F88 BSR 7:0 PCL[7:0] TO PD 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 0x1F89 WREG 7:0 0x1F8A PCLATH 7:0 0x1F8B INTCON 7:0 0x1F8C Reserved BSR[5:0] WREG[7:0] PCLATH[6:0] GIE (c) 2018 Microchip Technology Inc. PEIE INTEDG Datasheet Preliminary DS40002000A-page 657 PIC16(L)F18424/44 Register Summary Offset Name Bit Pos. 0x1FE4 STATUS_SHAD 7:0 0x1FE5 WREG_SHAD 7:0 0x1FE6 BSR_SHAD 7:0 0x1FE7 PCLATH_SHAD 7:0 0x1FE8 FSR0_SHAD 0x1FEA FSR1_SHAD 0x1FEC Reserved 0x1FED STKPTR ... 0x1FE3 0x1FEE TOS TO PD DC C WREG[7:0] BSR[5:0] PCLATH[6:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 FSRL[7:0] 15:8 FSRH[7:0] 7:0 STKPTR[4:0] 7:0 TOSL[7:0] 15:8 TOSH[7:0] (c) 2018 Microchip Technology Inc. Z Datasheet Preliminary DS40002000A-page 658 PIC16(L)F18424/44 In-Circuit Serial ProgrammingTM (ICSPTM) 39. In-Circuit Serial ProgrammingTM (ICSPTM) ICSPTM programming allows customers to manufacture circuit boards with unprogrammed devices. Programming can be done after the assembly process, allowing the device to be programmed with the most recent firmware or a custom firmware. Five pins are needed for ICSPTM programming: * * * * * ICSPCLK ICSPDAT MCLR/VPP VDD VSS In Program/Verify mode the program memory, User IDs and the Configuration Words are programmed through serial communications. The ICSPDAT pin is a bidirectional I/O used for transferring the serial data and the ICSPCLK pin is the clock input. For more information on ICSPTM refer to the " Memory Programming Specification" (DS40001970). 39.1 High-Voltage Programming Entry Mode The device is placed into High-Voltage Programming Entry mode by holding the ICSPCLK and ICSPDAT pins low then raising the voltage on MCLR/VPP to VIHH. 39.2 Low-Voltage Programming Entry Mode (R) The Low-Voltage Programming Entry mode allows the PIC Flash MCUs to be programmed using VDD only, without high voltage. When the LVP bit of Configuration Words is set to `1', the low-voltage ICSP programming entry is enabled. To disable the Low-Voltage ICSP mode, the LVP bit must be programmed to `0'. Entry into the Low-Voltage Programming Entry mode requires the following steps: 1. 2. MCLR is brought to Vil. A 32-bit key sequence is presented on ICSPDAT, while clocking ICSPCLK. Once the key sequence is complete, MCLR must be held at VIL for as long as Program/Verify mode is to be maintained. If low-voltage programming is enabled (LVP = 1), the MCLR Reset function is automatically enabled and cannot be disabled. See the MCLR Section for more information. The LVP bit can only be reprogrammed to `0' by using the High-Voltage Programming mode. Related Links MCLR 39.3 Common Programming Interfaces Connection to a target device is typically done through an ICSPTM header. A commonly found connector on development tools is the RJ-11 in the 6P6C (6-pin, 6-connector) configuration. See Figure 39-1. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 659 PIC16(L)F18424/44 In-Circuit Serial ProgrammingTM (ICSPTM) Figure 39-1. ICD RJ-11 Style Connector Interface VDD ICSPDAT NC 2 4 6 ICSPCLK 1 3 5 Target VPP/MCLR VSS PC Board Bottom Side Pin Description* 1 = VPP/MCLR 2 = VDD Target 3 = VSS (ground) 4 = ICSPDAT 5 = ICSPCLK 6 = No Connect Another connector often found in use with the PICkitTM programmers is a standard 6-pin header with 0.1 inch spacing. Refer to Figure 39-2. For additional interface recommendations, refer to the specific device programmer manual prior to PCB design. It is recommended that isolation devices be used to separate the programming pins from other circuitry. The type of isolation is highly dependent on the specific application and may include devices such as resistors, diodes, or even jumpers. See Figure 39-3 for more information. Figure 39-2. PICkitTM Programmer Style Connector Interface Pin 1 Indicator 1 2 3 4 5 6 Pin Description1 1 = VPP/MCLR 2 = VDD Target 3 = VSS (ground) 4 = ICSPDAT (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 660 PIC16(L)F18424/44 In-Circuit Serial ProgrammingTM (ICSPTM) 5 = ICSPCLK 6 = No Connect Note: 1. Note: The 6-pin header (0.100" spacing) accepts 0.025" square pins. Figure 39-3. Typical Connection for ICSPTM Programming External Programming Signals Device to be Programmed VDD VDD VDD VPP MCLR/VPP VSS VSS Data ICSPDAT Clock ICSPCLK * * * To Normal Connections * Isolation devices (as required). (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 661 PIC16(L)F18424/44 Instruction Set Summary 40. Instruction Set Summary PIC16(L)F18424/44 devices incorporate the standard set of 50 PIC16 core instructions. Each instruction is a 14-bit word containing the operation code (opcode) and all required operands. The opcodes are broken into three broad categories: * Byte Oriented * Bit Oriented * Literal and Control The literal and control category contains the most varied instruction word format. TM The Instruction Set table lists the instructions recognized by the MPASM assembler. All instructions are executed within a single instruction cycle, with the following exceptions, which may take two or three cycles: * Subroutine entry takes two cycles (CALL, CALLW) * Returns from interrupts or subroutines take two cycles (RETURN, RETLW, RETFIE) * Program branching takes two cycles (GOTO, BRA, BRW, BTFSS, BTFSC, DECFSZ, INCSFZ) * One additional instruction cycle will be used when any instruction references an indirect file register and the file select register is pointing to program memory. One instruction cycle consists of 4 oscillator cycles; for an oscillator frequency of 4 MHz, this gives a nominal instruction execution rate of 1 MHz. All instruction examples use the format `0xhh' to represent a hexadecimal number, where `h' signifies a hexadecimal digit. 40.1 Read-Modify-Write Operations Any WRITE instruction that specifies a file register as part of the instruction performs a Read-Modify-Write (R-M-W) operation. The register is read, the data is modified, and the result is stored according to either the working (W) register, or the originating file register, depending on the state of the destination designator 'd' (see the table below for more information). A read operation is performed on a register even if the instruction writes to that register. Table 40-1. Opcode Field Descriptions Field f Description Register file address (0x00 to 0x7F) W Working register (accumulator) b Bit address within an 8-bit file register k Literal field, constant data or label x Don't care location (= 0 or 1). The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. d Destination select; d = 0: store result in W, d = 1: store result in file register f. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 662 PIC16(L)F18424/44 Instruction Set Summary Field n mm Description FSR or INDF number. (0-1) Prepost increment-decrement mode selection Table 40-2. Abbreviation Descriptions Field Description PC Program Counter TO Time-Out bit C Carry bit DC Digit Carry bit Z Zero bit PD 40.2 Power-Down bit Standard Instruction Set Table 40-3. Instruction Set Mnemonic, Operands Description Cycles 14-Bit Opcode MSb Status Notes Affected LSb BYTE-ORIENTED OPERATIONS ADDWF f, d ADDWFC f, d Add WREG and f 1 00 0111 dfff ffff C, DC, Z 2 Add WREG and CARRY bit to f 1 11 1101 dfff ffff C, DC, Z 2 ANDWF f, d AND WREG with f 1 00 0101 dfff ffff Z 2 ASRF f, d Arithmetic Right Shift 1 11 0111 dfff ffff C, Z 2 LSLF f, d Logical Left Shift 1 11 0101 dfff ffff C, Z 2 LSRF f, d Logical Right Shift 1 11 0110 dfff ffff C, Z 2 CLRF f Clear f 1 00 0001 lfff ffff Z 2 CLRW - Clear WREG 1 00 0001 0000 00xx Z COMF f, d Complement f 1 00 1001 dfff ffff Z 2 DECF f, d Decrement f 1 00 0011 dfff ffff Z 2 INCF f, d Increment f 1 00 1010 dfff ffff Z 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 663 PIC16(L)F18424/44 Instruction Set Summary Mnemonic, Operands Description Cycles 14-Bit Opcode MSb Status Notes Affected LSb IORWF f, d Inclusive OR WREG with f 1 00 0100 dfff ffff Z 2 MOVF f, d Move f 1 00 1000 dfff ffff Z 2 MOVWF f Move WREG to f 1 00 0000 1fff ffff None 2 RLF f, d Rotate Left f through Carry 1 00 1101 dfff ffff C 2 RRF f, d Rotate Right f through Carry 1 00 1100 dfff ffff C 2 SUBWF f, d Subtract WREG from f 1 00 0010 dfff ffff C, DC, Z 2 Subtract WREG from f with borrow 1 11 1011 dfff ffff C, DC, Z 2 SUBWFB f, d SWAPF f, d Swap nibbles in f 1 00 1110 dfff ffff None 2 XORWF f, d Exclusive OR WREG with f 1 00 0110 dfff ffff Z 2 BYTE ORIENTED SKIP OPERATIONS DECFSZ f, d Decrement f, Skip if 0 1(2) 00 1011 dfff ffff None 1, 2 INCFSZ f, d Increment f, Skip if 0 1(2) 00 1111 dfff ffff None 1, 2 BCF f, b Bit Clear f 1 01 00bb bfff ffff None 2 BSF f, b Bit Set f 1 01 01bb bfff ffff None 2 BIT-ORIENTED FILE REGISTER OPERATIONS BIT-ORIENTED SKIP OPERATIONS BTFSC f, b Bit Test f, Skip if Clear 1(2) 01 10bb bfff ffff None 1, 2 BTFSS f, b Bit Test f, Skip if Set 1(2) 1010 11bb bfff ffff None 1, 2 LITERAL OPERATIONS ADDLW k Add literal and WREG 1 11 1110 kkkk kkkk C, DC, Z ANDLW k AND literal with WREG 1 11 1001 kkkk kkkk Z IORLW k Inclusive OR literal with WREG 1 11 1000 kkkk kkkk Z MOVLB k Move literal to BSR 1 00 000 0k kkkk None MOVLP k Move literal to PCLATH 1 11 0001 1kkk kkkk None (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 664 PIC16(L)F18424/44 Instruction Set Summary Mnemonic, Operands Description Cycles 14-Bit Opcode MSb Status Notes Affected LSb MOVLW k Move literal to W 1 11 0000 kkkk kkkk None SUBLW k Subtract W from literal 1 11 1100 kkkk kkkk C, DC, Z XORLW k Exclusive OR literal with W 1 11 1010 kkkk kkkk Z CONTROL OPERATIONS BRA k Relative Branch 2 11 001k kkkk kkkk None BRW -- Relative Branch with WREG 2 00 0000 0000 1011 None CALL k Call Subroutine 2 10 0kkk kkkk kkkk None CALLW -- Call Subroutine with WREG 2 00 0000 0000 1010 None GOTO k Go to address 2 10 1kkk kkkk kkkk None RETFIE k Return from interrupt 2 00 0000 0000 1001 None RETLW k Return with literal in WREG 2 11 0100 kkkk kkkk None RETURN -- Return from Subroutine 2 00 0000 0000 1000 None INHERENT OPERATIONS CLRWDT -- Clear Watchdog Timer 1 00 0000 0110 0100 TO, PD NOP -- No Operation 1 00 0000 0000 0000 None RESET -- Software device Reset 1 00 0000 0000 0001 None SLEEP -- Go into Standby or Idle mode 1 00 0000 0110 0011 TO, PD TRIS f Load TRIS register with WREG 1 00 0000 0110 0fff None C-COMPILER OPTIMIZED ADDFSR n, k MOVIW MOVWI Add Literal k to FSRn n, mm Move Indirect FSRn to WREG with pre/ post inc/dec modifier, mm k[n] Move INDFn to WREG, Indexed Indirect. n, mm Move WREG to Indirect FSRn with pre/ post inc/dec modifier, mm k[n] Move WREG to INDFn, Indexed Indirect. 1 (c) 2018 Microchip Technology Inc. 1 11 0001 0nkk kkkk None 1 00 0000 0001 0nmm Z 1 11 1111 0nkk kkkk Z 1 00 0000 0001 1nmm None 2, 3 11 1111 1nkk kkkk None 2 Datasheet Preliminary 2, 3 2 DS40002000A-page 665 PIC16(L)F18424/44 Instruction Set Summary Note: 1. If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. 2. 3. 40.2.1 If this instruction addresses an INDF register and the MSb of the corresponding FSR is set, this instruction will require one additional instruction cycle. Details on MOVIW and MOVWI instruction descriptions are available in the next section. Standard Instruction Set ADDFSR Add Literal to FSRn Syntax: [ label ] ADDFSR FSRn, k Operands: -32 k 31; n [ 0, 1] Operation: FSR(n) + k FSR(n) Status Affected: None Description: The signed 6-bit literal `k' is added to the contents of the FSRnH:FSRnL register pair. FSRn is limited to the range 0000h-FFFFh. Moving beyond these bounds will cause the FSR to wrap-around. ADDLW ADD literal to W Syntax: [ label ] ADDLW k Operands: 0 k 255 Operation: (W) + k (W) Status Affected: C, DC, Z Description: The contents of W are added to the 8-bit literal `k' and the result is placed in W. ADDWF ADD W to f Syntax: [ label ] ADDWF f, d Operands: 0 f 127 d [0,1] Operation: (W) + (f) dest Status Affected: C, DC, Z Description: Add the contents of the W register with register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 666 PIC16(L)F18424/44 Instruction Set Summary ADDWFC ADD W and CARRY bit to f Syntax: [ label ] ADDWFC f {,d} Operands: 0 f 127 d [0,1] Operation: (W) + (f) + (C) dest Status Affected: C, DC, Z Description: Add W, the Carry flag and data memory location `f'. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed in data memory location `f'. ANDLW AND literal with W Syntax: [ label ] ANDLW k Operands: 0 k 255 Operation: (W) .AND. k (W) Status Affected: Z Description: The contents of W are AND'ed with the 8-bit literal `k'. The result is placed in W. ANDWF AND W with f Syntax: [ label ] ANDWF f, d Operands: 0 f 127 d [0,1] Operation: (W) .AND. (f) dest Status Affected: Z Description: AND the W register with register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. ASRF Arithmetic Right Shift Syntax: [ label ] ASRF f, d Operands: 0 f 127 d [0,1] (f<7>) dest<7> Operation: (f<7:1>) dest<6:0> (f<0>) C (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 667 PIC16(L)F18424/44 Instruction Set Summary ASRF Arithmetic Right Shift Status Affected: C, Z The contents of register `f' are shifted one bit to the right through the Carry flag. The MSb remains unchanged. If `d' is `0', the result is placed in W. If `d' is `1', the result is stored back in register `f'. Description: Register f C BCF Bit Clear f Syntax: [ label ] BCF f, b Operands: 0 f 127 0b7 Operation: 0 f Status Affected: None Description: Bit `b' in register `f' is cleared. BRA Relative Branch Syntax: [ label ] BRA label [ label ] BRA $+k Operands: -256 label - PC + 255 -256 k 255 Operation: (PC) + 1 + k PC Status Affected: None Description: Add the signed 9-bit literal `k' to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 1 + k. This instruction is a 2-cycle instruction. This branch has a limited range. BRW Relative Branch with W Syntax: [ label ] BRW Operands: None Operation: (PC) + (W) PC (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 668 PIC16(L)F18424/44 Instruction Set Summary BRW Relative Branch with W Status Affected: None Description: Add the contents of W (unsigned) to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 1 + (W). This instruction is a 2-cycle instruction. BSF Bit Set f Syntax: [ label ] BSF f, b Operands: 0 f 127 0b7 Operation: 1 (f) Status Affected: None Description: Bit `b' in register `f' is set. BTFSC Bit Test File, Skip if Clear Syntax: [ label ] BTFSC f, b Operands: 0 f 127 0b7 Operation: skip if (f) = 0 Status Affected: None Description: If bit `b' in register `f' is `1', the next instruction is executed. If bit `b', in register `f', is `0', the next instruction is discarded, and a NOP is executed instead, making this a 2-cycle instruction. BTFSS Bit Test File, Skip if Set Syntax: [ label ] BTFSS f, b Operands: 0 f 127 0b<7 Operation: skip if (f) = 1 Status Affected: None Description: If bit `b' in register `f' is `0', the next instruction is executed. If bit `b' is `1', then the next instruction is discarded, and a NOP is executed instead, making this a 2-cycle instruction. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 669 PIC16(L)F18424/44 Instruction Set Summary CALL Subroutine Call Syntax: [ label ] CALL k Operands: 0 k 2047 Operation: (PC) + 1 TOS, k PC<10:0>, (PCLATH<6:3>) PC<14:11> Status Affected: None Description: Call Subroutine. First, return address (PC + 1) is pushed onto the stack. The 11-bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a 2-cycle instruction. CALLW Subroutine Call with W Syntax: [ label ] CALLW Operands: None Operation: (PC) + 1 TOS, (W) PC<7:0>, (PCLATH<6:0>) PC<14:8> Status Affected: Description: None Subroutine call with W. First, the return address (PC + 1) is pushed onto the return stack. Then, the contents of W is loaded into PC<7:0>, and the contents of PCLATH into PC<14:8>. CALLW is a 2-cycle instruction. CLRF Clear f Syntax: [ label ] CLRF f Operands: 0 f 127 Operation: 000h f 1Z Status Affected: Z Description: The contents of register `f' are cleared and the Z bit is set. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 670 PIC16(L)F18424/44 Instruction Set Summary CLRW Clear W Syntax: [ label ] CLRW Operands: None Operation: 00h (W) 1Z Status Affected: Z Description: W register is cleared. Zero bit (Z) is set. CLRWDT Clear Watchdog Timer Syntax: [ label ] CLRWDT Operands: None 00h WDT, 00h WDT prescaler, Operation: 1 TO, 1 PD Status Affected: TO, PD Description: CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits, TO and PD, are set. COMF Complement f Syntax: [ label ] COMF f, d Operands: 0 f 127 d [0,1] Operation: (f) dest Status Affected: Z Description: The contents of register `f' are complemented. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f'. DECF Decrement f Syntax: [ label ] DECF f, d Operands: 0 f 127 d [0,1] Operation: (f) - 1 dest (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 671 PIC16(L)F18424/44 Instruction Set Summary DECF Decrement f Status Affected: Z Description: Decrement register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. DECFSZ Decrement f, skip if 0 Syntax: [ label ] DECFSZ f, d Operands: 0 f 127 d [0,1] Operation: (f) - 1 dest, skip if result = 0 Description: The contents of register `f' are decremented. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'. If the result is `1', the next instruction is executed. If the result is `0', then a NOP is executed instead, making it a 2-cycle instruction. GOTO Unconditional Branch Syntax: [ label ] GOTO k Operands: 0 k 2047 Operation: k PC<10:0> PCLATH<6:3> PC<14:11> Status Affected: None Description: GOTO is an unconditional branch. The 11-bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a 2-cycle instruction. INCF Increment f Syntax: [ label ] INCF f, d Operands: 0 f 127 d [0,1] Operation: (f) + 1 dest (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 672 PIC16(L)F18424/44 Instruction Set Summary INCF Increment f Status Affected: Z Description: The contents of register `f' are incremented. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'. INCFSZ Increment f, skip if 0 Syntax: [ label ] INCFSZ f, d Operands: 0 f 127 d [0,1] Operation: (f) + 1 dest, skip if result = 0 Status Affected: None Description: The contents of register `f' are incremented. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'. If the result is `1', the next instruction is executed. If the result is `0', a NOP is executed instead, making it a 2-cycle instruction. IORLW Inclusive OR literal with W Syntax: [ label ] IORLW k Operands: 0 k 255 Operation: (W) .OR. k (W) Status Affected: Z Description: The contents of W are ORed with the 8-bit literal `k'. The result is placed in W. IORWF Inclusive OR W with f Syntax: IORWF f, d Operands: 0 f 127 d [0,1] Operation: (W) .OR. (f) dest (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 673 PIC16(L)F18424/44 Instruction Set Summary IORWF Inclusive OR W with f Status Affected: Z Description: Inclusive OR the W register with register `f'. If `d' is `0', the result is placed in the W register. If `d' is `1', the result is placed back in register `f'. LSLF Logical Left Shift Syntax: [ label ] LSLF f {,d} Operands: 0 f 127 d [0,1] Operation: (f<7>) C (f<6:0>) dest<7:1> 0 dest<0> Status Affected: Description: C, Z The contents of register `f' are shifted one bit to the left through the Carry flag. A `0' is shifted into the LSb. If `d' is `0', the result is placed in W. If `d' is `1', the result is stored back in register `f'. C Register f 0 LSRF Logical Right Shift Syntax: [ label ] LSRF f {,d} Operands: 0 f 127 d [0,1] Operation: 0 dest<7> (f<7:1>) dest<6:0>, (f<0>) C Status Affected: Description: C, Z The contents of register `f' are shifted one bit to the right through the Carry flag. A `0' is shifted into the MSb. If `d' is `0', the result is placed in W. If `d' is `1', the result is stored back in register `f'. 0 register f C (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 674 PIC16(L)F18424/44 Instruction Set Summary MOVF Move f Syntax: [ label ] MOVF f, d Operands: 0 f 127 d [0,1] Operation: f dest Status Affected: Z Description: The contents of register f is moved to a destination dependent upon the status of d. If d = 0, destination is W register. If d = 1, the destination is file register f itself. d = 1 is useful to test a file register since status flag Z is affected. Words: 1 Cycles: 1 Example: MOVF FSR, 0 After Instruction W = value in FSR register Z=1 MOVIW Move INDFn to W [ label ] MOVIW ++FSRn [ label ] MOVIW --FSRn Syntax: [ label ] MOVIW FSRn++ [ label ] MOVIW FSRn-[ label ] MOVIW k[FSRn] Operands: n [0,1] mm [00,01,10,11] -32 k 31 INDFn (W) Operation: Effective address is determined by * FSR + 1 (preincrement) * FSR - 1 (predecrement) * FSR + k (relative offset) After the Move, the FSR value will be either: * FSR + 1 (all increments) * FSR - 1 (all decrements) * Unchanged (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 675 PIC16(L)F18424/44 Instruction Set Summary MOVIW Move INDFn to W Z MODE Status Affected: Description: SYNTAX mm Preincrement ++FSRn 00 Predecrement --FSRn 01 Postincrement FSRn++ 10 Postdecrement FSRn-- 11 This instruction is used to move data between W and one of the indirect registers (INDFn). Before/after this move, the pointer (FSRn) is updated by pre/post incrementing/ decrementing it. The INDFn registers are not physical registers. Any instruction that accesses an INDFn register actually accesses the register at the address specified by the FSRn. FSRn is limited to the range 0000h - FFFFh. Incrementing/decrementing it beyond these bounds will cause it to wrap-around. MOVLB Move literal to BSR Syntax: [ label ] MOVLB k Operands: 0 k 127 Operation: k BSR Status Affected: None Description: The 6-bit literal `k' is loaded into the Bank Select Register (BSR). MOVLP Move literal to PCLATH Syntax: [ label ] MOVLP k Operands: 0 k 127 Operation: k PCLATH Status Affected: None Description: The 7-bit literal `k' is loaded into the PCLATH register. MOVLW Move literal to W Syntax: [ label ] MOVLW k Operands: 0 k 255 Operation: k (W) Status Affected: None (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 676 PIC16(L)F18424/44 Instruction Set Summary MOVLW Move literal to W Description: The 8-bit literal `k' is loaded into W register. The "don't cares" will assemble as `0's. Words: 1 Cycles: 1 Example: MOVLW 5Ah After Instruction W = 5Ah MOVWF Move W to f Syntax: [ label ] MOVWF f Operands: 0 f 127 Operation: (W) f Status Affected: None Description: Move data from W to register `f'. Words: 1 Cycles: 1 Example: MOVWF LATA Before Instruction LATA = FFh W = 4Fh After Instruction LATA = 4Fh W = 4Fh MOVWI Move W to INDFn [ label ] MOVWI ++FSRn [ label ] MOVWI --FSRn Syntax: [ label ] MOVWI FSRn++ [ label ] MOVWI FSRn-[ label ] MOVWI k[FSRn] Operands: n [0,1] mm [00,01,10,11] (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 677 PIC16(L)F18424/44 Instruction Set Summary MOVWI Move W to INDFn -32 k 31 (W) INDFn Operation: Effective address is determined by * FSR + 1 (preincrement) * FSR - 1 (predecrement) * FSR + k (relative offset) After the Move, the FSR value will be either: * FSR + 1 (all increments) * FSR - 1 (all decrements) * Unchanged None MODE Status Affected: Description: SYNTAX mm Preincrement ++FSRn 00 Predecrement --FSRn 01 Postincrement FSRn++ 10 Postdecrement FSRn-- 11 This instruction is used to move data between W and one of the indirect registers (INDFn). Before/after this move, the pointer (FSRn) is updated by pre/post incrementing/ decrementing it. The INDFn registers are not physical registers. Any instruction that accesses an INDFn register actually accesses the register at the address specified by the FSRn. FSRn is limited to the range 0000h-FFFFh. Incrementing/decrementing it beyond these bounds will cause it to wrap-around. The increment/decrement operation on FSRn WILL NOT affect any Status bits. NOP No Operation Syntax: [ label ] NOP Operands: None Operation: No operation Status Affected: None Description: No operation. Words: 1 Cycles: 1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 678 PIC16(L)F18424/44 Instruction Set Summary NOP Example: None. RESET Software Reset Syntax: [ label ] RESET Operands: None Operation: Execute a device Reset. Resets the RI flag of the PCON register. Status Affected: None Description: This instruction provides a way to execute a hardware Reset by software. RETFIE Return from Interrupt Syntax: [ label ] RETFIE k Operands: None Operation: (TOS) PC, 1 GIE Status Affected: None Description: Return from Interrupt. Stack is POPed and Top-of-Stack (TOS) is loaded in the PC. Interrupts are enabled by setting Global Interrupt Enable bit, GIE (INTCON<7>). This is a 2-cycle instruction. Words: 1 Cycles: 2 Example: RETFIE After Interrupt PC = TOS GIE = 1 RETLW Return literal to W Syntax: [ label ] RETLW k Operands: 0 k 255 Operation: k (W), (TOS) PC, Status Affected: None (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 679 PIC16(L)F18424/44 Instruction Set Summary RETLW Return literal to W Description: The W register is loaded with the 8-bit literal `k'. The program counter is loaded from the top of the stack (the return address). This is a 2-cycle instruction. Words: 1 Cycles: 2 Example: CALL TABLE ; offset value ; W now has ; table value : TABLE ADDWF PC RETLW k1 RETLW k2 : : RETLW kn ; W contains table ; W = offset ; Begin table ; ; End of table Before Instruction W = 07h After Instruction W = value of k8 RETURN Return from Subroutine Syntax: [ label ] RETURN Operands: None Operation: (TOS) PC, Status Affected: None Encoding: Description: 0000 0000 0001 001s Return from subroutine. The stack is POPped and the top of the stack (TOS) is loaded into the Program Counter. This is a 2-cycle instruction. RLF Rotate Left f through Carry Syntax: [ label ] RLF f, d Operands: 0 f 127 d [0,1] Operation: (f) dest, (f<7>) C, (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 680 PIC16(L)F18424/44 Instruction Set Summary RLF Rotate Left f through Carry (C) dest<0> Status Affected: C Encoding: Description: 0011 01da ffff ffff The contents of register `f' are rotated one bit to the left through the CARRY flag. If `d' is `0', the result is placed in W. If `d' is `1', the result is stored back in register `f' (default). C Words: 1 Cycles: 1 Example: register f RLF REG1, 0 Before Instruction REG1 = 1110 0110 C=0 After Instruction REG = 1110 0110 W = 1100 1100 C=1 RRF Rotate Right f through Carry Syntax: [ label ] RRF f, d Operands: 0 f 127 d [0,1] Operation: (f) dest, (f<0>) C, (C) dest<7> Status Affected: C Description: The contents of register `f' are rotated one bit to the right through the CARRY flag. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). C (c) 2018 Microchip Technology Inc. register f Datasheet Preliminary DS40002000A-page 681 PIC16(L)F18424/44 Instruction Set Summary SLEEP Enter Sleep mode Syntax: [ label ] SLEEP Operands: None 00h WDT, 0 WDT prescaler, Operation: 1 TO, 0 PD Status Affected: TO, PD Description: The Power-down Status bit (PD) is cleared. The Time-out Status bit (TO) is set. Watchdog Timer and its prescaler are cleared. SUBLW Subtract W from literal Syntax: [ label ] SUBLW k Operands: 0 k 255 Operation: k - (W) (W) Status Affected: C, DC, Z The W register is subtracted (2's complement method) from the 8-bit literal `k'. The result is placed in the W register. C =0, W > k Description C = 1, W k DC = 0, W[3:0] > k[3:0] DC = 1, W[3:0] k[3:0] SUBWF Subtract W from f Syntax: [ label ] SUBWF f, d Operands: 0 f 127 d [0,1] Operation: (f) - (W) (dest) Status Affected: C, DC, Z Description Subtract (2's complement method) W register from register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f. C =0, W > f (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 682 PIC16(L)F18424/44 Instruction Set Summary SUBWF Subtract W from f C = 1, W f DC = 0, W[3:0] > f[3:0] DC = 1, W[3:0] f[3:0] SUBFWB Subtract W from f with Borrow Syntax: [ label ] SUBFWB f {,d} Operands: 0 f 127 d [0,1] Operation: (W) - (f) - (B) dest Status Affected: C, DC, Z Description: Subtract W and the BORROW flag (CARRY) from register `f' (2's complement method). If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f'. SWAPF Swap Nibbles in f Syntax: [ label ] SWAPF f, d Operands: 0 f 127 d [0,1] Operation: (f<3:0>) dest<7:4>, (f<7:4>) dest<3:0> Status Affected: None Description: The upper and lower nibbles of register `f' are exchanged. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed in register `f' (default). TRIS Load TRIS Register with W Syntax: [ label ] TRIS f Operands: 5f7 Operation: (W) TRIS register `f' Status Affected: None Description: Move data from W register to TRIS register. When `f' = 5, TRISA is loaded. When `f' = 6, TRISB is loaded. When `f' = 7, TRISC is loaded. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 683 PIC16(L)F18424/44 Instruction Set Summary XORLW Exclusive OR literal with W Syntax: [ label ] XORLW k Operands: 0 k 255 Operation: (W) .XOR. k (W) Status Affected: Z Description: The contents of W are XORed with the 8-bit literal `k'. The result is placed in W. XORWF Exclusive OR W with f Syntax: [ label ] XORWF f, d Operands: 0 f 127 d [0,1] Operation: (W) .XOR. (f) dest Status Affected: Z Description: Exclusive OR the contents of the W register with register `f'. If `d' is `0', the result is stored in the W register. If `d' is `1', the result is stored back in register `f'. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 684 PIC16(L)F18424/44 Development Support 41. Development Support (R) (R) The PIC microcontrollers (MCU) and dsPIC digital signal controllers (DSC) are supported with a full range of software and hardware development tools: * * * * * * * * 41.1 Integrated Development Environment (R) - MPLAB X IDE Software Compilers/Assemblers/Linkers - MPLAB XC Compiler - MPASMTM Assembler - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB Assembler/Linker/Librarian for Various Device Families Simulators - MPLAB X SIM Software Simulator Emulators - MPLAB REAL ICETM In-Circuit Emulator In-Circuit Debuggers/Programmers - MPLAB ICD 3 - PICkitTM 3 Device Programmers - MPLAB PM3 Device Programmer Low-Cost Demonstration/Development Boards, Evaluation Kits and Starter Kits Third-party development tools MPLAB X Integrated Development Environment Software The MPLAB X IDE is a single, unified graphical user interface for Microchip and third-party software, and (R) (R) hardware development tool that runs on Windows , Linux and Mac OS X. Based on the NetBeans IDE, MPLAB X IDE is an entirely new IDE with a host of free software components and plug-ins for highperformance application development and debugging. Moving between tools and upgrading from software simulators to hardware debugging and programming tools is simple with the seamless user interface. With complete project management, visual call graphs, a configurable watch window and a feature-rich editor that includes code completion and context menus, MPLAB X IDE is flexible and friendly enough for new users. With the ability to support multiple tools on multiple projects with simultaneous debugging, MPLAB X IDE is also suitable for the needs of experienced users. Feature-Rich Editor: * * * * Color syntax highlighting Smart code completion makes suggestions and provides hints as you type Automatic code formatting based on user-defined rules Live parsing User-Friendly, Customizable Interface: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 685 PIC16(L)F18424/44 Development Support * * Fully customizable interface: toolbars, toolbar buttons, windows, window placement, etc. Call graph window Project-Based Workspaces: * * * * Multiple projects Multiple tools Multiple configurations Simultaneous debugging sessions File History and Bug Tracking: * * 41.2 Local file history feature Built-in support for Bugzilla issue tracker MPLAB XC Compilers The MPLAB XC Compilers are complete ANSI C compilers for all of Microchip's 8, 16, and 32-bit MCU and DSC devices. These compilers provide powerful integration capabilities, superior code optimization and ease of use. MPLAB XC Compilers run on Windows, Linux or MAC OS X. For easy source level debugging, the compilers provide debug information that is optimized to the MPLAB X IDE. The free MPLAB XC Compiler editions support all devices and commands, with no time or memory restrictions, and offer sufficient code optimization for most applications. MPLAB XC Compilers include an assembler, linker and utilities. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. MPLAB XC Compiler uses the assembler to produce its object file. Notable features of the assembler include: * * * * * * 41.3 Support for the entire device instruction set Support for fixed-point and floating-point data Command-line interface Rich directive set Flexible macro language MPLAB X IDE compatibility MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for PIC10/12/16/18 MCUs. (R) The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code, and COFF files for debugging. The MPASM Assembler features include: * * Integration into MPLAB X IDE projects User-defined macros to streamline assembly code (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 686 PIC16(L)F18424/44 Development Support * * 41.4 Conditional assembly for multipurpose source files Directives that allow complete control over the assembly process MPLINK Object Linker/MPLIB Object Librarian The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler. It can link relocatable objects from precompiled libraries, using directives from a linker script. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: * * * 41.5 Efficient linking of single libraries instead of many smaller files Enhanced code maintainability by grouping related modules together Flexible creation of libraries with easy module listing, replacement, deletion and extraction MPLAB Assembler, Linker and Librarian for Various Device Families MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, PIC32 and dsPIC DSC devices. MPLAB XC Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: * * * * * * 41.6 Support for the entire device instruction set Support for fixed-point and floating-point data Command-line interface Rich directive set Flexible macro language MPLAB X IDE compatibility MPLAB X SIM Software Simulator The MPLAB X SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB X SIM Software Simulator fully supports symbolic debugging using the MPLAB XC Compilers, and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 687 PIC16(L)F18424/44 Development Support 41.7 MPLAB REAL ICE In-Circuit Emulator System The MPLAB REAL ICE In-Circuit Emulator System is Microchip's next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs all 8, 16 and 32-bit MCU, and DSC devices with the easy-to-use, powerful graphical user interface of the MPLAB X IDE. The emulator is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with in-circuit debugger systems (RJ-11) or with the new high-speed, noise tolerant, Low-Voltage Differential Signal (LVDS) interconnection (CAT5). The emulator is field upgradable through future firmware downloads in MPLAB X IDE. MPLAB REAL ICE offers significant advantages over competitive emulators including full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, logic probes, a ruggedized probe interface and long (up to three meters) interconnection cables. 41.8 MPLAB ICD 3 In-Circuit Debugger System The MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost-effective, high-speed hardware debugger/programmer for Microchip Flash DSC and MCU devices. It debugs and programs PIC Flash microcontrollers and dsPIC DSCs with the powerful, yet easy-to-use graphical user interface of the MPLAB IDE. The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a highspeed USB 2.0 interface and is connected to the target with a connector compatible with the MPLAB ICD 2 or MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 supports all MPLAB ICD 2 headers. 41.9 PICkit 3 In-Circuit Debugger/Programmer The MPLAB PICkit 3 allows debugging and programming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB IDE. The MPLAB PICkit 3 is connected to the design engineer's PC using a full-speed USB interface and can be connected to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the Reset line to implement in-circuit debugging and In-Circuit Serial ProgrammingTM (ICSPTM). 41.10 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at Vddmin and Vddmax for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages, and a modular, detachable socket assembly to support various package types. The ICSP cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices, and incorporates an MMC card for file storage and data applications. 41.11 Demonstration/Development Boards, Evaluation Kits, and Starter Kits A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 688 PIC16(L)F18424/44 Development Support areas for adding custom circuitry and provide application firmware and source code for examination and modification. The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEMTM and dsPICDEMTM demonstration/development board series of circuits, (R) Microchip has a line of evaluation kits and demonstration software for analog filter design, KeeLoq (R) (R) security ICs, CAN, IrDA , PowerSmart battery management, SEEVAL evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. 41.12 Third-Party Development Tools Microchip also offers a great collection of tools from third-party vendors. These tools are carefully selected to offer good value and unique functionality. * * * * * Device Programmers and Gang Programmers from companies, such as SoftLog and CCS Software Tools from companies, such as Gimpel and Trace Systems Protocol Analyzers from companies, such as Saleae and Total Phase (R) Demonstration Boards from companies, such as MikroElektronika, Digilent and Olimex (R) Embedded Ethernet Solutions from companies, such as EZ Web Lynx, WIZnet and IPLogika (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 689 PIC16(L)F18424/44 Electrical Specifications 42. Electrical Specifications 42.1 Absolute Maximum Ratings() Parameter Ambient temperature under bias Storage temperature Voltage on pins with respect to VSS * Rating -40C to +125C -65C to +150C on VDD pin: PIC16LF18424/44 -0.3V to +4.0V PIC16F18424/44 -0.3V to +6.5V * on MCLR pin: -0.3V to +9.0V * on all other pins: -0.3V to (VDD + 0.3V) Maximum current * on VSS pin(1) * on VDD pin(1) * on any standard I/O pin -40C TA +85C 85C < TA +125C -40C TA +85C 85C < TA +125C 250 mA 120 mA 250 mA 85 mA 50 mA Clamp current, IK (VPIN < 0 or VPIN > VDD) Total power dissipation(2) 20 mA 800 mW Important: 1. Maximum current rating requires even load distribution across I/O pins. Maximum current rating may be limited by the device package power dissipation characterizations, see Thermal Characteristics to calculate device specifications. 2. Power dissipation is calculated as follows: PDIS = VDD x {IDD - IOH} + {(VDD - VOH) x IOH} + (VOI x IOL) NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure above maximum rating conditions for extended periods may affect device reliability. 42.2 Standard Operating Conditions The standard operating conditions for any device are defined as: Operating Voltage: (c) 2018 Microchip Technology Inc. VDDMIN VDD VDDMAX Datasheet Preliminary DS40002000A-page 690 PIC16(L)F18424/44 Electrical Specifications TA_MIN TA TA_MAX Operating Temperature: Parameter Ratings VDD -- Operating Supply Voltage(1) VDDMIN (FOSC 16 MHz) PIC16LF18424/44 VDDMIN (FOSC 32 MHz) VDDMAX VDDMIN (FOSC 16 MHz) PIC16F18424/44 VDDMIN (FOSC 32 MHz) VDDMAX TA -- Operating Ambient Temperature Range TA_MIN Industrial Temperature TA_MAX TA_MIN Extended Temperature TA_MAX Note: 1. See Parameter D002, DC Characteristics: Supply Voltage. +1.8V +2.5V +3.6V +2.3V +2.5V +5.5V -40C +85C -40C +125C Figure 42-1. Voltage Frequency Graph, -40C TA +125C, for PIC16F18424/44 only Rev. 30-000069C 10/27/2016 VDD (V) 5.5 2.5 2.3 0 4 10 16 32 Frequency (MHz) Note: 1. The shaded region indicates the permissible combinations of voltage and frequency. 2. Refer to External Clock/Oscillator Timing Requirements for each Oscillator mode's supported frequencies. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 691 PIC16(L)F18424/44 Electrical Specifications Figure 42-2. Voltage Frequency Graph, -40C TA +125C, for PIC16LF18424/44 Devices only VDD (V) Rev. 30-000070B 10/27/2017 3.6 2.5 1.8 4 0 10 16 32 Frequency (MHz) Note: 1. The shaded region indicates the permissible combinations of voltage and frequency. 2. Refer to External Clock/Oscillator Timing Requirements for each Oscillator mode's supported frequencies. Related Links Supply Voltage 42.3 DC Characteristics 42.3.1 Supply Voltage Table 42-1. PIC16LF18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Characteristic Min. Typ. Max. Units Conditions 1.8 -- 3.6 V FOSC 16 MHz 2.5 -- 3.6 V FOSC > 16 MHz Supply Voltage D002 VDD RAM Data Retention(1) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 692 PIC16(L)F18424/44 Electrical Specifications PIC16LF18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. D003 VDR Characteristic Min. Typ. Max. Units Conditions 1.5 -- -- V Device in Sleep mode -- 1.6 -- V BOR or LPBOR disabled(3) -- 0.8 -- V BOR or LPBOR disabled(3) -- V/ms BOR or LPBOR disabled(3) Power-on Reset Release Voltage(2) D004 VPOR Power-on Reset Rearm Voltage(2) D005 VPORR VDD Rise Rate to ensure internal Power-on Reset signal(2) D006 SVDD 0.05 -- - Data in "Typ." column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. This is the limit to which VDD can be lowered in Sleep mode without losing RAM data. 2. See the following figure, POR and POR REARM with Slow Rising VDD. 3. Please see Reset, WDT, Oscillator Start-up Timer, Power-up Timer, Brown-Out Reset and LowPower Brown-Out Reset Specifications for BOR and LPBOR trip point information. PIC16F18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Characteristic Min. Typ. Max. Units Conditions 2.3 -- 5.5 V FOSC 16 MHz 2.5 -- 5.5 V FOSC > 16 MHz 1.7 -- -- V Device in Sleep mode -- 1.6 -- V BOR or LPBOR disabled(3) Supply Voltage D002 VDD RAM Data Retention(1) D003 VDR Power-on Reset Release Voltage(2) D004 VPOR Power-on Reset Rearm Voltage(2) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 693 PIC16(L)F18424/44 Electrical Specifications PIC16F18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. D005 VPORR Characteristic Min. Typ. Max. Units Conditions -- 1.5 -- V BOR or LPBOR disabled(3) -- V/ms BOR or LPBOR disabled(3) VDD Rise Rate to ensure internal Power-on Reset signal(2) D006 SVDD -- 0.05 - Data in "Typ." column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. This is the limit to which VDD can be lowered in Sleep mode without losing RAM data. 2. See the following figure, POR and POR REARM with Slow Rising VDD. 3. Please see Reset, WDT, Oscillator Start-up Timer, Power-up Timer, Brown-Out Reset and LowPower Brown-Out Reset Specifications for BOR and LPBOR trip point information. Figure 42-3. POR and POR Rearm with Slow Rising VDD Rev. 30-000071A 4/6/2017 VDD VPOR VPORR SVDD VSS NPOR(1) POR REARM VSS TVLOW(3) TPOR(2) Note: 1. When NPOR is low, the device is held in Reset. 2. TPOR 1 s typical. 3. TVLOW 2.7 s typical. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 694 PIC16(L)F18424/44 Electrical Specifications 42.3.2 Supply Current (IDD)(1,2,4) Table 42-2. PIC16LF18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Device Characteristics D100 IDDXT4 D101 Conditions Min. Typ. Max. Units XT = 4 MHz -- 530 805 A 3.0V IDDHFO16 HFINTOSC = 16 MHz -- 2.0 2.9 mA 3.0V D102 IDDHFOPLL HFINTOSC = 32 MHz -- 3.6 5.5 mA 3.0V D103 IDDHSPLL32 HS+PLL = 32 MHz -- 3.6 5.6 mA 3.0V IDDIDLE IDLE mode, HFINTOSC = 16 MHz -- 1.6 2.0 mA 3.0V IDDDOZE(3) DOZE mode, HFINTOSC = 16 MHz, Doze Ratio = 16 -- 1.4 -- mA 3.0V D104 D105 VDD Note - Data in "Typ." column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins are outputs driven low; MCLR = VDD; WDT disabled. 2. The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. 3. IDDDOZE = [IDDIDLE*(N-1)/N] + IDDHFO16/N where N = DOZE Ratio (see CPUDOZE register). 4. PMD bits are all in the default state, no modules are disabled. PIC16F18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Device Characteristics D100 IDDXT4 D101 IDDHFO16 Conditions Min. Typ. Max. Units XT = 4 MHz -- 560 845 A 3.0V HFINTOSC = 16 MHz -- 2.2 3.0 mA 3.0V (c) 2018 Microchip Technology Inc. Datasheet Preliminary VDD Note DS40002000A-page 695 PIC16(L)F18424/44 Electrical Specifications PIC16F18424/44 only Standard Operating Conditions (unless otherwise stated) Conditions Param. No. Sym. Device Characteristics Min. Typ. Max. Units D102 IDDHFOPLL HFINTOSC = 32 MHz -- 3.7 5.6 mA 3.0V D103 IDDHSPLL32 HS+PLL = 32 MHz -- 3.7 5.7 mA 3.0V D104 IDDIDLE IDLE mode, HFINTOSC = 16 MHz -- 1.8 2.1 mA 3.0V IDDDOZE(3) DOZE mode, HFINTOSC = 16 MHz, Doze Ratio = 16 -- 1.6 -- mA 3.0V D105 VDD Note - Data in "Typ." column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins are outputs driven low; MCLR = VDD; WDT disabled. 2. The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. 3. IDDDOZE = [IDDIDLE*(N-1)/N] + IDDHFO16/N where N = DOZE Ratio (see CPUDOZE register). 4. PMD bits are all in the default state, no modules are disabled. Related Links CPUDOZE 42.3.3 Power-Down Current (IPD)(1,2) Table 42-3. PIC16LF18424/44 only Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Device Characteristics D200 IPD D201 IPD_WDT Conditions Min. Typ. Max. +85C Max. +125C Units IPD Base -- 0.06 2 9 A 3.0V Low-Frequency Internal Oscillator/WDT -- 0.8 4.0 11.0 A 3.0V (c) 2018 Microchip Technology Inc. Datasheet Preliminary VDD Note DS40002000A-page 696 PIC16(L)F18424/44 Electrical Specifications PIC16LF18424/44 only Standard Operating Conditions (unless otherwise stated) Conditions Param. No. Sym. Device Characteristics Min. Typ. Max. +85C Max. +125C Units D202 IPD_SOSC Secondary Oscillator (SOSC) -- 0.6 5 11 A 3.0V D203 IPD_FVR FVR -- 33 74 76 A 3.0V D204 IPD_BOR Brown-out Reset (BOR) -- 10 17 19 A 3.0V D205 IPD_LPBOR Low-Power Brown-out Reset (LPBOR) -- 0.5 3.0 10.0 A 3.0V D207 IPD_ADCA ADC - Nonconverting -- 0.06 2 9 A 3.0V IPD_CMP Comparator -- D208 VDD Note ADC not converting (4) 30 48 56 A 3.0V - Data in "Typ." column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. The peripheral current is the sum of the base IDD and the additional current consumed when this peripheral is enabled. The peripheral current can be determined by subtracting the base IDD or IPDcurrent from this limit. Max. values should be used when calculating total current consumption. 2. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode with all I/O pins in high-impedance state and tied to VSS. 3. All peripheral currents listed are on a per-peripheral basis if more than one instance of a peripheral is available. 4. ADC clock source is FRC. PIC16F18424/44 only Standard Operating Conditions (unless otherwise stated), VREGPM = 1 Param. No. Sym. Device Characteristics D200 D200A D201 IPD IPD Base IPD_WDT Low-Frequency Internal Oscillator/WDT (c) 2018 Microchip Technology Inc. Conditions Min. Typ. Max. +85C Max. +125C Units -- 0.4 4 12 A 3.0V -- 18 22 27 A 3.0V -- 0.9 6.0 14 A 3.0V Datasheet Preliminary VDD Note VREGPM = 0 DS40002000A-page 697 PIC16(L)F18424/44 Electrical Specifications PIC16F18424/44 only Standard Operating Conditions (unless otherwise stated), VREGPM = 1 Conditions Param. No. Sym. Device Characteristics Min. Typ. Max. +85C Max. +125C Units D202 IPD_SOSC Secondary Oscillator (SOSC) -- 0.8 5.5 13 A 3.0V D203 IPD_FVR FVR -- 28 70 75 A 3.0V D204 IPD_BOR Brown-out Reset (BOR) -- 14 18 20 A 3.0V D207 IPD_ADCA ADC - Nonconverting -- 0.4 4 12 A 3.0V IPD_CMP Comparator -- D208 VDD Note ADC not converting (4) 33 49 57 A 3.0V - Data in "Typ." column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. The peripheral current is the sum of the base IDD and the additional current consumed when this peripheral is enabled. The peripheral current can be determined by subtracting the base IDD or IPDcurrent from this limit. Max. values should be used when calculating total current consumption. 2. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode with all I/O pins in high-impedance state and tied to VSS. 3. 4. All peripheral currents listed are on a per-peripheral basis if more than one instance of a peripheral is available. ADC clock source is FRC. 42.3.4 I/O Ports Table 42-4. Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Device Characteristics Min. Typ. Max. Units Conditions -- -- 0.8 V 4.5VVDD5.5V -- -- 0.15 VDD V 1.8VVDD4.5V 2.0VVDD5.5V Input Low Voltage VIL D300 I/O PORT: * with TTL buffer D301 D302 * with Schmitt Trigger buffer -- -- 0.2 VDD V D303 * with I2C levels -- -- 0.3 VDD V D304 * with SMBus levels -- -- 0.8 V (c) 2018 Microchip Technology Inc. Datasheet Preliminary 2.7VVDD5.5V DS40002000A-page 698 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param. No. Sym. D305 Device Characteristics MCLR Min. Typ. Max. Units Conditions -- -- 0.2 VDD V 2.0 -- -- V 4.5VVDD5.5V 0.25 VDD +0.8 -- -- V 1.8VVDD4.5V 2.0VVDD5.5V Input High Voltage VIH I/O PORT: D320 * with TTL buffer D321 D322 * with Schmitt Trigger buffer 0.8VDD -- -- V D323 * with I2C levels 0.7 VDD -- -- V D324 * with SMBus levels 2.1 -- -- V 0.7 VDD -- -- V -- 5 125 nA VSSVPINVDD, Pin at high-impedance, 85C -- 5 1000 nA VSSVPINVDD, Pin at high-impedance, 125C -- 50 200 nA VSSVPINVDD, Pin at high-impedance, 85C 25 120 200 A VDD=3.0V, VPIN=VSS -- -- 0.6 V IOL = 8 mA, VDD = 5.0V IOL = 6 mA, VDD = 3.3V D325 MCLR 2.7VVDD5.5V Input Leakage Current(1) D340 IIL I/O PORTS D341 MCLR(2) D342 Weak Pull-up Current D350 IPUR Output Low Voltage D360 VOL Standard I/O PORTS IOL = 1.8 mA, VDD = 1.8V D360A High-Drive I/O PORTS -- -- -- 0.6 0.6 -- V V I OL -- 0.6 -- V = 10 mA, V DD = 2.3V, HIDCx = 1 IOL = 32 mA, VDD = 3.0V, HIDCx = 1 IOL = 51 mA, VDD = 5.0V, HIDCx = 1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 699 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Device Characteristics Min. Typ. Max. Units VDD-0.7 -- -- V Conditions Output High Voltage D370 VOH Standard I/O PORTS IOH = 3.5 mA, VDD = 5.0V IOH = 3 mA, VDD = 3.3V IOH = 1 mA, VDD = 1.8V D370A High-Drive I/O PORTS VDD-0.7 -- VDD-0.7 -- -- V V VDD-0.7 -- V IOH = 10 mA, VDD = 2.3V, HIDCx = 1 IOH = 37 mA, VDD = 3.0V, HIDCx = 1 IOH = 54 mA, VDD = 5.0V, HIDCx = 1 All I/O Pins D380 CIO -- 5 50 pF - Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. Negative current is defined as current sourced by the pin. 2. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 42.3.5 Memory Programming Specifications Table 42-5. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Device Characteristics Min. Typ Max. Units Conditions High Voltage Entry Programming Mode Specifications MEM01 VIHH Voltage on MCLR/VPP pin to enter programming mode 8 -- 9 V (Note 2, Note 3) MEM02 IPPGM Current on MCLR/VPP pin during programming mode -- 1 -- mA (Note 2) -- -- -- V (Note 4) Programming Mode Specifications MEM10 VBE VDD for Bulk Erase (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 700 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param No. MEM11 Sym. IDDPGM Device Characteristics Supply Current during Programming operation Min. Typ Max. Units -- -- 10 mA 100k -- -- E/W Conditions Data EEPROM Memory Specifications MEM20 ED DataEE Byte Endurance MEM21 TD_RET Characteristic Retention MEM22 MEM23 MEM24 ND_REF VD_RW TD_BEW Year Provided no other specifications are violated -- 40 Total Erase/Write Cycles before Refresh -- -- VDD for Read or Erase/Write operation VDDMIN -- VDDMAX V -- 4.0 5.0 ms 10k -- -- E/W -40CTa +85C (Note 1) Provided no other specifications are violated Byte Erase and Write Cycle Time -- -40CTA +85C 100k E/W Program Flash Memory Specifications MEM30 MEM32 EP TP_RET Flash Memory Cell Endurance Characteristic Retention -- 40 -- Year MEM33 VP_RD VDD for Read operation VDDMIN -- VDDMAX V MEM34 VP_REW VDD for Row Erase or Write operation VDDMIN -- VDDMAX V MEM35 TP_REW Self-Timed Row Erase or Self-Timed Write -- 2.0 2.5 ms - Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 701 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param No. 1. 2. 3. 4. Sym. Device Characteristics Min. Typ Max. Units Conditions Flash Memory Cell Endurance for the Flash memory is defined as: One Row Erase operation and one Self-Timed Write. Required only if CONFIG4, bit LVP is disabled. (R) The MPLAB ICD2 does not support variable VPP output. Circuitry to limit the ICD2 VPP voltage must be placed between the ICD2 and target system when programming or debugging with the ICD2. Refer to the "PIC16(L)F184XX Memory Programming Specification" document for description. Related Links CONFIG4 42.3.6 Thermal Characteristics Table 42-6. Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Param No. Sym. Characteristic Typ. Units Conditions TH01 Thermal Resistance Junction to Ambient 70.0 C/W 14-pin PDIP package 95.3 C/W 14-pin SOIC package JA 100.0 C/W 14-pin TSSOP package TH02 TH03 JC TJMAX Thermal Resistance Junction to Case Maximum Junction Temperature (c) 2018 Microchip Technology Inc. 51.5 C/W 16-pin UQFN 4x4mm package 62.2 C/W 20-pin PDIP package 87.3 C/W 20-pin SSOP package 77.7 C/W 20-pin SOIC package 43.0 C/W 20-pin UQFN 4x4mm package 32.75 C/W 14-pin PDIP package 31.0 C/W 14-pin SOIC package 24.4 C/W 14-pin TSSOP package 5.4 C/W 16-pin UQFN 4x4mm package 27.5 C/W 20-pin PDIP package 31.1 C/W 20-pin SSOP package 23.1 C/W 20-pin SOIC package 5.3 C/W 20-pin UQFN 4x4mm package 150 C Datasheet Preliminary DS40002000A-page 702 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Param No. Sym. Characteristic Typ. Units Conditions TH04 PD Power Dissipation TH05 -- W PD=PINTERNAL+PI/O PINTERNAL Internal Power Dissipation -- W PINTERNAL=IDDxVDD(1) TH06 PI/O I/O Power Dissipation -- W PI/O=(IOL*VOL)+(IOH*(VDD-VOH)) TH07 PDER Derated Power -- W PDER=PDMAX (TJ-TA)/JA(2) Note: 1. IDD is current to run the chip alone without driving any load on the output pins. Filename: 10-000133A.vsd 2. TA = Ambient Temperature, TJ = JunctionLOAD Temperature. Title: CONDITION Last Edit: First Used: Note: 42.4 8/1/2013 PIC16F1508/9 AC Characteristics Figure 42-4. Load Conditions Rev. 10-000133A 8/1/2013 Load Condition Pin CL VSS Legend: CL=50 pF for all pins 42.4.1 External Clock/Oscillator Timing Requirements Figure 42-5. Clock Timing Rev. 30-000072A 4/6/2017 Q4 Q1 Q2 Q3 Q4 Q1 CLKIN OS1 OS2 OS2 OS20 CLKOUT (CLKOUT Mode) Note: See table below. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 703 PIC16(L)F18424/44 Electrical Specifications Table 42-7. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. Units Conditions ECL Oscillator OS1 FECL Clock Frequency -- -- 500 kHz OS2 TECL_DC Clock Duty Cycle 40 -- 60 % ECM Oscillator OS3 FECM Clock Frequency -- -- 4 MHz OS4 TECM_DC Clock Duty Cycle 40 -- 60 % ECH Oscillator OS5 FECH Clock Frequency -- -- 32 MHz OS6 TECH_DC Clock Duty Cycle 40 -- 60 % Clock Frequency -- -- 100 kHz Note 4 Clock Frequency -- -- 4 MHz Note 4 Clock Frequency -- -- 20 MHz Note 4 Clock Frequency 32.4 32.768 33.1 kHz Note 4 (Note 2, Note 3) LP Oscillator OS7 FLP XT Oscillator OS8 FXT HS Oscillator OS9 FHS Secondary Oscillator OS10 FSEC System Oscillator OS20 FOSC System Clock Frequency -- -- 32 MHz OS21 FCY Instruction Frequency -- FOSC/4 -- MHz OS22 TCY Instruction Period 125 1/FCY -- ns * These parameters are characterized but not tested. - Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 704 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param No. 2. 3. 4. Sym. Characteristic Min. Typ. Max. Units Conditions are tested to operate at "min" values with an external clock applied to OSC1 pin. When an external clock input is used, the "max" cycle time limit is "DC" (no clock) for all devices. The system clock frequency (FOSC) is selected by the "main clock switch controls" as described in the "Oscillator Module (with Fail-Safe Clock Monitor)" section. The system clock frequency (FOSC) must meet the voltage requirements defined in the "Standard Operating Conditions" section. LP, XT and HS oscillator modes require an appropriate crystal or resonator to be connected to the device. For clocking the device with the external square wave, one of the EC mode selections must be used. Related Links Oscillator Module (with Fail-Safe Clock Monitor) Standard Operating Conditions 42.4.2 Internal Oscillator Parameters(1) Table 42-8. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic OS50 FHFOSC Precision Calibrated HFINTOSC Frequency Min. Typ. Max. Units Conditions -- 4 -- MHz (Note 2) 8 12 16 32 OS51 FHFOSCLP Low-Power Optimized HFINTOSC Frequency -- 1 -- MHz -- 2 -- MHz OS52 FMFOSC Internal Calibrated MFINTOSC Frequency -- 500 -- kHz OS53 FLFOSC Internal LFINTOSC Frequency -- 31 -- kHz OS54 THFOSCST HFINTOSC Wakeup from Sleep Start-up Time -- 11 20 s VREGPM=0 -- 85 -- s VREGPM=1 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 705 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic OS56 TLFOSCST LFINTOSC Wakeup from Sleep Start-up Time Min. Typ. Max. Units -- 0.2 -- ms Conditions - Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as 0.1 F and 0.01 F values in parallel are recommended. close to the device as possible. 2. See the figure below. Figure 42-6. Precision Calibrated HFINTOSC Frequency Accuracy Over Device VDD and Temperature 125 5% Temperature (C) 85 3% 60 2% 0 5% -40 1.8 2.0 2.3 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 706 PIC16(L)F18424/44 Electrical Specifications 42.4.3 PLL Specifications Table 42-9. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. Units PLL01 FPLLIN PLL Input Frequency Range 4 -- 16 MHz PLL02 FPLLOUT PLL Output Frequency Range 16 -- 32 MHz PLL03 FPLLST PLL Lock Time from Start-up -- 200 -- s PLL04 FPLLJIT PLL Output Frequency Stability (Jitter) -0.25 -- 0.25 % Conditions (Note 1) * - These parameters are characterized but not tested. - Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. The output frequency of the PLL must meet the FOSC requirements listed in Parameter D002. 42.4.4 I/O and CLKOUT Timing Specifications Figure 42-7. CLKOUT and I/O Timing Rev. 30-000074A 4/6/2017 Cycle Write Fetch Q1 Q4 Read Execute Q2 Q3 FOSC IO2 IO1 IO10 CLKOUT IO8 IO4 IO7 IO5 I/O pin (Input) IO3 I/O pin (Output) New Value Old Value IO7, IO8 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 707 PIC16(L)F18424/44 Electrical Specifications Table 42-10. I/O and CLKOUT Timing Specifications Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. Units Conditions IO1* TCLKOUTH CLKOUT rising edge delay (rising edge FOSC (Q1 cycle) to falling edge CLKOUT -- -- 70 ns IO2* TCLKOUTL CLKOUT falling edge delay (rising edge FOSC (Q3 cycle) to rising edge CLKOUT -- -- 72 ns IO3* TIO_VALID Port output valid time (rising edge FOSC (Q1 cycle) to port valid) -- 50 70 ns IO4* TIO_SETUP Port input setup time (Setup time before rising edge FOSC - Q2 cycle) 20 -- -- ns IO5* TIO_HOLD Port input hold time (Hold time after rising edge FOSC - Q2 cycle) 50 -- -- ns IO6* TIOR_SLREN Port I/O rise time, slew rate enabled -- 25 -- ns VDD=3.0V IO7* TIOR_SLRDIS Port I/O rise time, slew rate disabled -- 5 -- ns VDD=3.0V IO8* TIOF_SLREN Port I/O fall time, slew rate enabled -- 25 -- ns VDD=3.0V IO9* TIOF_SLRDIS Port I/O fall time, slew rate disabled -- 5 -- ns VDD=3.0V IO10* TINT INT pin high or low time to trigger an interrupt 25 -- -- ns IO11* TIOC Interrupt-on-Change minimum high or low time to trigger interrupt 25 -- -- ns * - These parameters are characterized but not tested. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 708 PIC16(L)F18424/44 Electrical Specifications 42.4.5 Reset, WDT, Oscillator Start-up Timer, Power-up Timer, Brown-Out Reset and Low-Power BrownOut Reset Specifications Figure 42-8. Reset, Watchdog Timer, Oscillator Start-up Timer and Power-up Timer Timing Rev. 30-000075A 4/6/2017 VDD MCLR RST01 Internal POR RST04 PWRT Time-out RST05 OSC Start-up Time Internal Reset(1) Watchdog Timer Reset(1) RST03 RST02 RST02 I/O pins Note: 1. Asserted low. Figure 42-9. Brown-out Reset Timing and Characteristics Rev. 30-000076A 4/6/2017 VDD VBOR and VHYST VBOR (Device in Brown-out Reset) (Device not in Brown-out Reset) RST08 Reset (due to BOR) RST04(1) Note: 1. Only if PWRTE bit in the Configuration Word register is programmed to `1'; 2 ms delay if PWRTE = 0. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 709 PIC16(L)F18424/44 Electrical Specifications Table 42-11. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. Units RST01* TMCLR MCLR Pulse Width Low to ensure Reset 2 -- -- s RST02* TIOZ I/O high-impedance from Reset detection -- -- 2 s RST03 TWDT Watchdog Timer Time-out Period -- 16 -- ms RST04* TPWRT Power-up Timer Period -- 65 -- ms RST05 TOST Oscillator Start-up Timer Period(1, 2) -- 1024 -- TOSC RST06 VBOR Brown-out Reset Voltage 2.55 2.7 2.85 2.30 2.45 2.60(3) V V 1.80 1.90 2.05 V Conditions 1:512 Prescaler BORV=0 BORV=1(F devices only) BORV=1(LF Devices only) RST07 VBORHYS Brown-out Reset Hysteresis -- 40 -- mV RST08 TBORDC Brown-out Reset Response Time -- 3 -- s RST09 VLPBOR Low-Power Brownout Reset Voltage 1.8 1.9 2.2 V * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. By design, the Oscillator Start-up Timer (OST) counts the first 1024 cycles, independent of frequency. 2. To ensure these voltage tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible. 0.1 F and 0.01 F values in parallel are recommended. 3. This value corresponds to VBORMAX (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 710 PIC16(L)F18424/44 Electrical Specifications 42.4.6 Temperature Indicator Requirements Table 42-12. Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Characteristic TS01 TACQMIN Minimum ADC Acquisition Time Delay TS02 Mv Voltage Sensitivity Min. Max. Units Conditions -- 25 -- s High Range -- -3.684 -- mV/C TSRNG = 1 Low Range -- -3.456 -- mV/C TSRNG = 0 * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 42.4.7 Analog-To-Digital Converter (ADC) Accuracy Specifications(1,2) Table 42-13. Standard Operating Conditions (unless otherwise stated) VDD = 3.0V, TA = 25C, TAD = 1s Param No. Sym. Characteristic Min. Typ. Max. AD01 NR AD02 Units Conditions Resolution -- -- 12 bit EIL Integral Error -- 1.0 0.2 LSb ADCREF+=3.0V, ADCREF- = 0V AD03 EDL Differential Error -- 1.0 1.0 LSb ADCREF+=3.0V, ADCREF- = 0V AD04 EOFF Offset Error -- 0.5 6.0 LSb ADCREF+=3.0V, ADCREF- = 0V AD05 EGN Gain Error -- 0.2 6.0 LSb ADCREF+=3.0V, ADCREF- = 0V AD06 VADREF ADC Reference Voltage (ADREF+ - ADREF-) 1.8 -- VDD V AD07 VAIN Full-Scale Range ADREF- -- ADREF+ V AD08 ZAIN Recommended Impedance of Analog Voltage Source -- 10 -- k AD09 RVREF ADC Voltage Reference Ladder Impedance -- 50 -- k * - These parameters are characterized but not tested. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 711 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) VDD = 3.0V, TA = 25C, TAD = 1s Param No. Sym. Characteristic Min. Typ. Max. Units Conditions Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. Total Absolute Error is the sum of the offset, gain and integral non-linearity (INL) errors. 2. The ADC conversion result never decreases with an increase in the input and has no missing codes. 42.4.8 Analog-to-Digital Converter (ADC) Conversion Timing Specifications Table 42-14. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic AD20 TAD ADC Clock Period AD21 AD22 TCNV Conversion Time(1) Min. Typ. Max. Units Conditions 1 -- 9 s Using FOSC as the ADC clock source ADCS = 1 -- 2 -- s Using FRC as the ADC clock source ADCS = 0 -- 13TAD+3TCY -- -- Using FOSC as the ADC clock source ADCS = 1 -- 16TAD+2TCY -- -- Using FRC as the ADC clock source ADCS = 0 AD23 TACQ Acquisition Time -- 2 -- s AD24 THCD Sample and Hold Capacitor Disconnect Time -- 2TAD+1TCY -- -- Using FOSC as the ADC clock source ADCS = 1 -- 3TAD+2TCY -- -- Using FRC as the ADC clock source ADCS = 0 * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. Does not apply for the ADCRC oscillator. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 712 PIC16(L)F18424/44 Electrical Specifications Figure 42-10. ADC Conversion Timing (ADC Clock FOSC-Based) Rev. 30-000077B 12/04/2017 BSF ADCON0, GO AD24 1 TCY AD22 Q4 11 ADC Data 10 9 8 3 2 1 0 NEW_DATA OLD_DATA ADRES 1 TCY ADIF GO Sample DONE Sampling Stopped AD23 Figure 42-11. ADC Conversion Timing (ADC Clock from ADCRC) Rev. 30-000078B 12/04/2017 BSF ADCON0, GO AD24 1 TCY AD22 Q4 AD20 ADC_clk 11 ADC Data 10 9 8 3 OLD_DATA ADRES 1 0 NEW_DATA 1 TCY ADIF GO Sample 2 DONE AD23 Sampling Stopped Note: 1. If the ADC clock source is selected as ADCRC, a time of TCY is added before the ADC clock starts. This allows the SLEEP instruction to be executed. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 713 PIC16(L)F18424/44 Electrical Specifications 42.4.9 Comparator Specifications Table 42-15. Standard Operating Conditions (unless otherwise stated) VDD = 3.0V, TA = 25C Param No. Sym. Characteristic Min. Typ. Max. Units Conditions CM01 VIOFF Input Offset Voltage -- 30 -- mV VICM = VDD/2 CM02 VICM Input Common Mode Range GND -- VDD V CM03 CMRR Common Mode Input Rejection Ratio -- 50 -- dB CM04 VHYST Comparator Hysteresis 15 25 35 mV CM05 TRESP(1) Response Time, Rising Edge -- 300 600 ns Response Time, Falling Edge -- 220 500 ns Mode Change to Valid Output -- -- 10 ns CM06* TMCV2VO(2) * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. Response time measured with one comparator input at VDD/2, while the other input transitions from VSS to VDD. 2. A mode change includes changing any of the control register values, including module enable. 42.4.10 5-Bit DAC Specifications Table 42-16. Standard Operating Conditions (unless otherwise stated) VDD = 3.0V, TA = 25C Param No. Sym. Characteristic Min. Typ. Max. Units DSB01 VLSB Step Size -- (VDACREF+VDACREF-)/32 -- V DSB02 VACC Absolute Accuracy -- -- 0.5 LSb (c) 2018 Microchip Technology Inc. Datasheet Preliminary Conditions DS40002000A-page 714 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) VDD = 3.0V, TA = 25C Param No. Sym. Characteristic Min. Typ. Max. Units DSB03* RUNIT Unit Resistor Value -- 5000 -- DSB04* TST Settling Time(1) -- -- 10 s Conditions * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. Settling time measured while DACR<4:0> transitions from `00000' to `01111'. 42.4.11 Fixed Voltage Reference (FVR) Specifications Table 42-17. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. Units Conditions FVR01 VFVR1 1x Gain (1.024V) -4 -- +4 % VDD2.5V, -40C to 85C FVR02 VFVR2 2x Gain (2.048V) -4 -- +4 % VDD2.5V, -40C to 85C FVR03 VFVR4 4x Gain (4.096V) -5 -- +5 % VDD4.75V, -40C to 85C FVR04 TFVRST FVR Start-up Time -- 60 -- s 42.4.12 Zero-Cross Detect (ZCD) Specifications Table 42-18. Standard Operating Conditions (unless otherwise stated) VDD = 3.0V, TA = 25C Param No. Sym. Characteristic Min. Typ. Max. Units ZC01 VPINZC Voltage on Zero Cross Pin -- 0.75 -- V ZC02 IZCD_MAX Maximum source or sink current -- -- 600 A ZC03 TRESPH Response Time, Rising Edge -- 1 -- s TRESPL Response Time, Falling Edge -- 1 -- s Conditions Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 715 PIC16(L)F18424/44 Electrical Specifications 42.4.13 Timer0 and Timer1 External Clock Requirements Table 42-19. Standard Operating Conditions (unless otherwise stated) Operating Temperature: -40CTA+125C Param No. Sym. Characteristic 40* TT0H T0CKI High Pulse Width No Prescaler T0CKI Low Pulse Width No Prescaler 41* TT0L Min. Typ. Max. 0.5TCY +20 -- -- ns 10 -- -- ns 0.5TCY +20 -- -- ns 10 -- -- ns Greater of: 20 or (TCY +40)/N -- -- ns Synchronous, No Prescaler 0.5TCY +20 -- -- ns Synchronous, with Prescaler 15 -- -- ns Asynchronous 30 -- -- ns 0.5TCY +20 -- -- ns Synchronous, with Prescaler 15 -- -- ns Asynchronous 30 -- -- ns Synchronous Greater of: 30 or (TCY +40)/N -- -- ns Asynchronous 60 -- -- ns 2 TOSC -- 7 TOSC -- With Prescaler With Prescaler 42* TT0P T0CKI Period 45* TT1H T1CKI High Time 46* 47* 49* TT1L TT1P T1CKI Synchronous, Low Time No Prescaler T1CKI Input Period TCKEZTMR1 Delay from External Clock Edge to Timer Increment Units Conditions N = Prescale value N = Prescale value Timers in Sync mode * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 716 PIC16(L)F18424/44 Electrical Specifications Figure 42-12. Timer0 and Timing1 External Clock Timings Rev. 30-000079A 4/6/2017 T0CKI 40 41 42 T1CKI 45 46 49 47 TMR0 or TMR1 42.4.14 Capture/Compare/PWM Requirements (CCP) Table 42-20. Standard Operating Conditions (unless otherwise stated) Operating Temperature: -40CTA+125C Param No. Sym. Characteristic CC01* TCCL CCPx Input Low Time No Prescaler 0.5TCY+20 CCPx Input High Time No Prescaler 0.5TCY+20 CC02* CC03* TCCH TCCP CCPx Input Period Min. With Prescaler With Prescaler Typ. Max. -- -- ns -- -- ns -- -- ns 20 -- -- ns (3TCY +40)/N -- -- ns 20 Units Conditions N = Prescale value * - These parameters are characterized but not tested. Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 717 PIC16(L)F18424/44 Electrical Specifications Figure 42-13. Capture/Compare/PWM Timings (CCP) Rev. 30-000080A 4/6/2017 CCPx (Capture mode) CC01 CC02 CC03 Note: Refer to Figure 42-4 for load conditions. 42.4.15 Configurable Logic Cell (CLC) Characteristics Table 42-21. Standard Operating Conditions (unless otherwise stated) Operating Temperature: -40CTA+125C Param No. Sym. Characteristic Min. Typ. Max. Units Conditions CLC01* TCLCIN CLC input time -- 7 OS5 ns (Note1) CLC02* TCLC CLC module input to output propagation time -- 24 -- ns VDD = 1.8V -- 12 -- ns VDD > 3.6V CLC output time Rise Time -- OS7 -- -- (Note1) Fall Time -- OS8 -- -- (Note1) -- 32 FOSC CLC03* CLC04* TCLCOUT FCLCMAX CLC maximum switching frequency MHz * - These parameters are characterized but not tested. - Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note: 1. See "I/O and CLKOUT Timing Specifications" for OS5, OS7 and OS8 rise and fall times. Figure 42-14. CLC Propagation Timing Rev. 30-000153A 10/27/2017 CLCxINn CLC Input time CLCxINn CLC Input time CLC01 LCx_in[n](1) LCx_in[n](1) CLC Module LCx_out(1) CLC Output time CLCx CLC Module LCx_out(1) CLC Output time CLCx CLC02 CLC03 Related Links (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 718 PIC16(L)F18424/44 Electrical Specifications I/O and CLKOUT Timing Specifications 42.4.16 EUSART Synchronous Transmission Requirements Table 42-22. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic US120 TCKH2DTV SYNC XMIT (Master and Slave) -- 80 ns 3.0VVDD5.5V Clock high to data-out valid -- 100 ns 1.8VVDD5.5V Clock out rise time and fall time -- 45 ns 3.0VVDD5.5V (Master mode) -- 50 ns 1.8VVDD5.5V Data-out rise time and fall time -- 45 ns 3.0VVDD5.5V -- 50 ns 1.8VVDD5.5V US121 TCKRF US122 TDTRF Min. Max. Units Conditions Figure 42-15. EUSART Synchronous Transmission (Master/Slave) Timing Rev. 30-000081A 4/6/2017 CK US121 US121 DT US122 US120 Note: Refer to Figure 42-4 for load conditions. 42.4.17 EUSART Synchronous Receive Requirements Table 42-23. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Max. Units Conditions US125 TDTV2CKL SYNC RCV (Master and Slave) 10 -- ns 15 -- ns Data-setup before CK (DT hold time) US126 TCKL2DTL Data-hold after CK (DT hold time) Figure 42-16. EUSART Synchronous Receive (Master/Slave) Timing Rev. 30-000082A 4/6/2017 CK US125 DT US126 Note: Refer to Figure 42-4 for load conditions. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 719 PIC16(L)F18424/44 Electrical Specifications 42.4.18 SPI Mode Requirements Table 42-24. Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. SP70* TSSL2SCH, SS to SCK or SCK input 2.25*TCY -- -- ns TSSL2SCL Units Conditions SP71* TSCH SCK input high time (Slave mode) TCY + 20 -- -- ns SP72* TSCL SCK input low time (Slave mode) TCY + 20 -- -- ns SP73* TDIV2SCH, Setup time of SDI data input to SCK edge 100 -- -- ns Hold time of SDI data input to SCK edge 100 -- -- ns SDO data output rise time -- 10 25 ns 3.0VVDD5.5V -- 25 50 ns 1.8VVDD5.5V TDIV2SCL SP74* TSCH2DIL, TSCL2DIL SP75* TDOR SP76* TDOF SDO data output fall time -- 10 25 ns SP77* TSSH2DOZ SS to SDO output high-impedance 10 -- 50 ns SP78* TSCR SCK output rise time (Master mode) -- 10 25 ns 3.0VVDD5.5V -- 25 50 ns 1.8VVDD5.5V SP79* TSCF SCK output fall time (Master mode) -- 10 25 ns SP80* TSCH2DOV, SDO data output valid after SCK edge -- -- 50 ns 3.0VVDD5.5V -- -- 145 ns 1.8VVDD5.5V SDO data output setup to SCK edge 1 TCY -- -- ns -- -- 50 ns 1.5 TCY + 40 -- -- ns TSCL2DOV SP81* TDOV2SCH, TDOV2SCL SP82* TSSL2DOV SDO data output valid after SS edge SP83* TSCH2SSH, SS after SCK edge TSCL2SSH * - These parameters are characterized but not tested. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 720 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param No. Sym. Characteristic Min. Typ. Max. Units Conditions Data in "Typ" column is at 3.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Figure 42-17. SPI Master Mode Timing (CKE = 0, SMP = 0) Rev. 30-000083A 4/6/2017 SS SP81 SCK (CKP = 0) SP71 SP72 SP78 SP79 SP79 SP78 SCK (CKP = 1) SP80 bit 6 - - - - - -1 MSb SDO LSb SP75, SP76 SDI MSb In bit 6 - - - -1 LSb In SP74 SP73 Note: Refer to Figure 42-4 for load conditions. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 721 PIC16(L)F18424/44 Electrical Specifications Figure 42-18. SPI Master Mode Timing (CKE = 1, SMP = 1) Rev. 30-000084A 4/6/2017 SS SP81 SCK (CKP = 0) SP71 SP72 SP79 SP73 SCK (CKP = 1) SP80 SDO MSb SP78 LSb bit 6 - - - - - -1 SP75, SP76 SDI MSb In bit 6 - - - -1 LSb In SP74 Note: Refer to Figure 42-4 for load conditions. Figure 42-19. SPI Slave Mode Timing (CKE = 0) Rev. 30-000085A 4/6/2017 SS SP70 SCK (CKP = 0) SP83 SP71 SP72 SP78 SP79 SP79 SP78 SCK (CKP = 1) SP80 SDO MSb bit 6 - - - - - -1 LSb SP77 SP75, SP76 SDI MSb In bit 6 - - - -1 LSb In SP74 SP73 Note: Refer to Figure 42-4 for load conditions. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 722 PIC16(L)F18424/44 Electrical Specifications Figure 42-20. SPI Slave Mode Timing (CKE = 1) Rev. 30-000086A 4/6/2017 SP82 SS SP70 SP83 SCK (CKP = 0) SP71 SP72 SCK (CKP = 1) SP80 MSb SDO bit 6 - - - - - -1 LSb SP77 SP75, SP76 SDI MSb In bit 6 - - - -1 LSb In SP74 Note: Refer to Figure 42-4 for load conditions. 42.4.19 I2C Bus Start/Stop Bits Requirements Table 42-25. Standard Operating Conditions (unless otherwise stated) Param. No. Sym. SP90* SP91* SP92* SP93* Characteristic Min. Typ. Max. Units Conditions TSU:STA Start condition 100 kHz mode Setup time 400 kHz mode 4700 -- -- 600 -- -- THD:STA Start condition 100 kHz mode Hold time 400 kHz mode 4000 -- -- 600 -- -- TSU:STO Stop condition 100 kHz mode Setup time 400 kHz mode 4700 -- -- 600 -- -- THD:STO Stop condition 100 kHz mode Hold time 4000 -- -- (c) 2018 Microchip Technology Inc. Datasheet Preliminary ns Only relevant for Repeated Start Setup time 400 kHz mode 600 condition ns After this period, the first clock Hold time 400 kHz mode 600 -- -- pulse is generated ns ns DS40002000A-page 723 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Characteristic Min. Typ. Max. Units Conditions 400 kHz mode 600 -- -- * - These parameters are characterized but not tested. Figure 42-21. I2C Bus Start/Stop Bits Timing Rev. 30-000087A 4/6/2017 SCL SP93 SP91 SP90 SP92 SDA Stop Condition Start Condition Note: Refer to Figure 42-4 for load conditions. 42.4.20 I2C Bus Data Requirements Table 42-26. Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Characteristic SP100* THIGH Clock high time SP101* TLOW Clock low time (c) 2018 Microchip Technology Inc. Min. Max. Units 100 kHz mode 4.0 -- s Device must operate at a minimum of 1.5 MHz 400 kHz mode 0.6 -- s Device must operate at a minimum of 10 MHz SSP module 1.5TCY -- 100 kHz mode 4.7 -- s Device must operate at a minimum of 1.5 MHz 400 kHz mode 1.3 -- s Device must operate at a minimum of 10 MHz Datasheet Preliminary Conditions DS40002000A-page 724 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param. No. SP102* SP103* SP106* SP107* SP109* SP110* SP111 Sym. TR TF THD:DAT TSU:DAT TAA TBUF CB Characteristic Min. Max. SSP module 1.5TCY -- SDA and SCL rise time 100 kHz mode -- 1000 ns 400 kHz mode 20 + 0.1CB 300 ns SDA and SCL fall time 100 kHz mode -- 250 ns 400 kHz mode 20 + 0.1CB 250 ns Data input hold time 100 kHz mode 0 -- ns 400 kHz mode 0 0.9 s 100 kHz mode 250 -- ns 400 kHz mode 100 -- ns Output valid from clock 100 kHz mode -- 3500 ns 400 kHz mode -- -- ns Bus free time 100 kHz mode 4.7 -- s 400 kHz mode 1.3 -- s -- 400 pF Data input setup time Bus capacitive loading Units Conditions CB is specified to be from 10-400 pF CB is specified to be from 10-400 pF (Note 2) (Note 1) Time the bus must be free before a new transmission can start * - These parameters are characterized but not tested. Note: 1. As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions. 2. A Fast mode (400 kHz) I2C bus device can be used in a Standard mode (100 kHz) I2C bus system, but the requirement TSU:DAT250 ns must then be met. This will automatically be the case (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 725 PIC16(L)F18424/44 Electrical Specifications Standard Operating Conditions (unless otherwise stated) Param. No. Sym. Characteristic Min. Max. Units Conditions if the device does not stretch the low period of the SCL signal. If such a device does stretch the low period of the SCL signal, it must output the next data bit to the SDA line TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification), before the SCL line is released. Figure 42-22. I2C Bus Data Timing Rev. 30-000088A 4/6/2017 SP103 SCL SP100 SP90 SP102 SP101 SP106 SP107 SP91 SDA In SP92 SP110 SP109 SP109 SDA Out Note: Refer to Figure 42-4 for load conditions. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 726 PIC16(L)F18424/44 DC and AC Characteristics Graphs and Tables 43. DC and AC Characteristics Graphs and Tables The graphs and tables provided in this section are for design guidance and are not tested. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are ensured to operate properly only within the specified range. Unless otherwise noted, all graphs apply to both the L and LF devices. Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore, outside the warranted range. Note: "Typical" represents the mean of the distribution at 25C. "Maximum", "Max.", "Minimum" or "Min." represents (mean + 3) or (mean - 3) respectively, where is a standard deviation, over each temperature range. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 727 PIC16(L)F18424/44 DC and AC Characteristics Graphs and Tables Graphs Figure 43-1. High Range Temperature Indicator Figure 43-2. Low Range Temperature Indicator Voltage Sensitivity Across Temperature Voltage Sensitivity Across Temperature -2.300 -3.450 -3.500 -2.350 -3.550 -2.400 Slope (mV/C) -3.600 Slope (mV/C) 43.1 -3.650 -3.700 -3.750 -2.450 -2.500 -3.800 -2.550 -3.850 -3.900 -2.600 -60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 Typical +3 Sigma (c) 2018 Microchip Technology Inc. 20 40 60 80 100 120 140 Temperature (oC) Temperature (oC) -3 Sigma Typical Datasheet Preliminary +3 Sigma -3 Sigma DS40002000A-page 728 PIC16(L)F18424/44 Packaging Information 44. Packaging Information Package Marking Information Rev. 30-009000A 5/17/2017 Legend: XX...X Y YY WW NNN Pe3 * Note: Customer-specific information or Microchip part number Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code b - free JEDEC (R) designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Rev. 30-009014A 09/21/2017 14-Lead PDIP (300 mil) Example PIC16F18424 /SO e3 1525017 Rev. 30-009014B 09/21/2017 14-Lead TSSOP (4.4 mm) Example XXXXXXXX YYWW NNN 16F18424 1525 e3 017 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 729 PIC16(L)F18424/44 Packaging Information Rev. 30-009014C 09/21/2017 14-Lead SOIC (3.90 mm) Example PIC16F18424 /SO e3 1525017 Rev. 30-009016A 09/21/2017 16-Lead UQFN (4x4x0.5 mm) PIN 1 Example PIN 1 PIC16 F18424 /MV 525017 e3 Rev. 30-009020A 09/21/2017 20-Lead PDIP (300 mil) XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN Example PIC16F18444 /P e3 1525017 Rev. 30-009020B 09/21/2017 20-Lead SSOP (5.30 mm) Example PIC16F18444 /SO e3 1525017 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 730 PIC16(L)F18424/44 Packaging Information Rev. 30-009020C 09/21/2017 20-Lead SOIC (7.50 mm) Example PIC16F18444 /SO e3 1525017 Rev. 30-009020D 09/21/2017 20-Lead UQFN (4x4x0.5 mm) PIN 1 Example PIN 1 PIC16 F18444 /MV 525017 e3 44.1 Package Details The following sections give the technical details of the packages. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 731 M PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information 14-Lead Plastic Dual In-Line (P) - 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE 1 E1 1 3 2 D E A2 A L A1 c b1 b e eB Units Dimension Limits Number of Pins INCHES MIN NOM N MAX 14 Pitch e Top to Seating Plane A - - .210 Molded Package Thickness A2 .115 .130 .195 Base to Seating Plane A1 .015 - - Shoulder to Shoulder Width E .290 .310 .325 Molded Package Width E1 .240 .250 .280 Overall Length D .735 .750 .775 Tip to Seating Plane L .115 .130 .150 Lead Thickness c .008 .010 .015 b1 .045 .060 .070 b .014 .018 .022 eB - - Upper Lead Width Lower Lead Width Overall Row Spacing .100 BSC .430 Notes: 1. Pin 1 visual index feature may vary, but must be located with the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-005B (c) 2007 Microchip Technology Inc. (c) 2018 Microchip Technology Inc. DS00049AR-page 47 Datasheet Preliminary DS40002000A-page 732 M PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. (c) 2018 Microchip Technology Inc. DS00049BC-page 111 Datasheet Preliminary DS40002000A-page 733 M Note: PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. DS00049BC-page 112 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 734 M PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2008 Microchip Technology Inc. (c) 2018 Microchip Technology Inc. DS00049AT-page 77 Datasheet Preliminary DS40002000A-page 735 M Note: PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2010 Microchip Technology Inc. DS00049BE-page 240 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 736 M PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. (c) 2018 Microchip Technology Inc. DS00049BC-page 103 Datasheet Preliminary DS40002000A-page 737 M Note: PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. DS00049BC-page 96 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 738 PIC16(L)F18424/44 Packaging Information 16-Lead Ultra Thin Plastic Quad Flat, No Lead Package (JQ) - 4x4x0.5 mm Body [UQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging A D B N NOTE 1 1 2 E (DATUM B) (DATUM A) 2X 0.20 C 2X TOP VIEW 0.20 C SEATING PLANE A1 0.10 C C A 16X (A3) 0.08 C SIDE VIEW 0.10 C A B D2 0.10 C A B E2 2 e 2 1 NOTE 1 K N 16X b 0.10 L e C A B BOTTOM VIEW Microchip Technology Drawing C04-257A Sheet 1 of 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 739 PIC16(L)F18424/44 Packaging Information 16-Lead Ultra Thin Plastic Quad Flat, No Lead Package (JQ) - 4x4x0.5 mm Body [UQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Units Dimension Limits Number of Pins N e Pitch A Overall Height Standoff A1 A3 Terminal Thickness Overall Width E E2 Exposed Pad Width D Overall Length D2 Exposed Pad Length b Terminal Width Terminal Length L K Terminal-to-Exposed-Pad MIN 0.45 0.00 2.50 2.50 0.25 0.30 0.20 MILLIMETERS NOM 16 0.65 BSC 0.50 0.02 0.127 REF 4.00 BSC 2.60 4.00 BSC 2.60 0.30 0.40 - MAX 0.55 0.05 2.70 2.70 0.35 0.50 - Notes : 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package is saw singulated 3. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-257A Sheet 2 of 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 740 PIC16(L)F18424/44 Packaging Information 16-Lead Ultra Thin Plastic Quad Flat, No Lead Package (JQ) - 4x4x0.5 mm Body [UQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging C1 X2 16 1 C2 Y2 2 Y1 X1 E SILK SCREEN RECOMMENDED LAND PATTERN Units Dimension Limits E Contact Pitch X2 Optional Center Pad Width Optional Center Pad Length Y2 Contact Pad Spacing C1 Contact Pad Spacing C2 Contact Pad Width (X16) X1 Contact Pad Length (X16) Y1 MIN MILLIMETERS NOM 0.65 BSC MAX 2.70 2.70 4.00 4.00 0.35 0.80 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-2257A (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 741 M PIC16(L)F18424/44 Packaging Information Packaging Diagrams and Parameters 20-Lead Plastic Dual In-Line (P) - 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N E1 NOTE 1 1 2 3 D E A2 A L c A1 b1 b eB e Units Dimension Limits Number of Pins INCHES MIN NOM N MAX 20 Pitch e Top to Seating Plane A - - .210 Molded Package Thickness A2 .115 .130 .195 Base to Seating Plane A1 .015 - - Shoulder to Shoulder Width E .300 .310 .325 Molded Package Width E1 .240 .250 .280 Overall Length D .980 1.030 1.060 Tip to Seating Plane L .115 .130 .150 Lead Thickness c .008 .010 .015 b1 .045 .060 .070 b .014 .018 .022 eB - - Upper Lead Width Lower Lead Width Overall Row Spacing .100 BSC .430 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-019B (c) 2007 Microchip Technology Inc. DS00049AR-page 52 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 742 M PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information 20-Lead Plastic Shrink Small Outline (SS) - 5.30 mm Body [SSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N E E1 NOTE 1 1 2 e b c A2 A A1 L1 Units Dimension Limits Number of Pins L MILLIMETERS MIN NOM N MAX 20 Pitch e Overall Height A - 0.65 BSC - 2.00 Molded Package Thickness A2 1.65 1.75 1.85 Standoff A1 0.05 - - Overall Width E 7.40 7.80 8.20 Molded Package Width E1 5.00 5.30 5.60 Overall Length D 6.90 7.20 7.50 Foot Length L 0.55 0.75 0.95 Footprint L1 1.25 REF Lead Thickness c 0.09 - Foot Angle 0 4 0.25 8 Lead Width b 0.22 - 0.38 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.20 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-072B (c) 2007 Microchip Technology Inc. DS00049AR-page 114 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 743 PIC16(L)F18424/44 Packaging Information 20-Lead Plastic Shrink Small Outline (SS) - 5.30 mm Body [SSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 0.65 0.45 SILK SCREEN c Y1 G X1 E RECOMMENDED LAND PATTERN Units Dimension Limits E Contact Pitch Contact Pad Spacing C Contact Pad Width (X20) X1 Contact Pad Length (X20) Y1 Distance Between Pads G MIN MILLIMETERS NOM 0.65 BSC 7.20 MAX 0.45 1.75 0.20 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing No. C04-2072B (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 744 M Note: PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. DS00049BC-page 102 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 745 M PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. DS00049BC-page 104 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 746 M Note: PIC16(L)F18424/44 Packaging Diagrams and Parameters Packaging Information For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2009 Microchip Technology Inc. DS00049BC-page 100 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 747 PIC16(L)F18424/44 Packaging Information 20-Lead Ultra Thin Plastic Quad Flat, No Lead Package (GZ) - 4x4x0.5 mm Body [UQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D A B N NOTE 1 1 2 E (DATUM B) (DATUM A) 2X 0.20 C 2X TOP VIEW 0.20 C 0.10 C C SEATING PLANE A1 A 20X (A3) 0.08 C SIDE VIEW 0.10 C A B D2 L 0.10 C A B E2 2 K 1 NOTE 1 N 20X b 0.10 e C A B BOTTOM VIEW Microchip Technology Drawing C04-255A Sheet 1 of 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 748 PIC16(L)F18424/44 Packaging Information 20-Lead Ultra Thin Plastic Quad Flat, No Lead Package (GZ) - 4x4x0.5 mm Body [UQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Units Dimension Limits Number of Terminals N e Pitch A Overall Height Standoff A1 A3 Terminal Thickness Overall Width E E2 Exposed Pad Width D Overall Length D2 Exposed Pad Length b Terminal Width Terminal Length L K Terminal-to-Exposed-Pad MIN 0.45 0.00 2.60 2.60 0.20 0.30 0.20 MILLIMETERS NOM 20 0.50 BSC 0.50 0.02 0.127 REF 4.00 BSC 2.70 4.00 BSC 2.70 0.25 0.40 - MAX 0.55 0.05 2.80 2.80 0.30 0.50 - Notes : 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package is saw singulated 3. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-255A Sheet 2 of 2 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 749 PIC16(L)F18424/44 Packaging Information 20-Lead Ultra Thin Plastic Quad Flat, No Lead Package (GZ) - 4x4x0.5 mm Body [UQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging C1 X2 20 1 2 C2 Y2 G1 Y1 X1 E SILK SCREEN RECOMMENDED LAND PATTERN Units Dimension Limits E Contact Pitch Optional Center Pad Width X2 Optional Center Pad Length Y2 Contact Pad Spacing C1 Contact Pad Spacing C2 Contact Pad Width (X20) X1 Contact Pad Length (X20) Y1 Contact Pad to Center Pad (X20) G1 MIN MILLIMETERS NOM 0.50 BSC MAX 2.80 2.80 4.00 4.00 0.30 0.80 0.20 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-2255A (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 750 PIC16(L)F18424/44 Revision A (02/2018) 45. Revision A (02/2018) Initial release of this document. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 751 PIC16(L)F18424/44 The Microchip Web Site Microchip provides online support via our web site at http://www.microchip.com/. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: * * * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives Customer Change Notification Service Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at http://www.microchip.com/. Under "Support", click on "Customer Change Notification" and follow the registration instructions. Customer Support Users of Microchip products can receive assistance through several channels: * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or Field Application Engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://www.microchip.com/support (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 752 PIC16(L)F18424/44 Product Identification System To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device [X](1) -X /XX Tape Temperature and Reel Range Package Device: PIC16F18424, PIC16LF18424, PIC16F18444, PIC16LF18444 Tape & Reel Option: Blank = Tube T = Tape & Reel I = -40C to +85C (Industrial) E = -40C to +125C (Extended) JQ = 16-lead UQFN 4x4x0.5mm P = 14-lead, 20-lead PDIP SL = 14-lead SOIC SO = 20-lead SOIC SS = 20-lead SSOP ST = 14-lead TSSOP GZ = 20-lead UQFN 4x4x0.5mm Temperature Range: Package: Pattern: QTP, SQTP, Code or Special Requirements (blank otherwise) Examples: * PIC16F18424- E/P Extended temperature PDIP package Note: 1. Tape and Reel identifier only appears in the catalog part number description. This identifier is used for ordering purposes and is not printed on the device package. Check with your Microchip Sales Office for package availability with the Tape and Reel option. 2. Small form-factor packaging options may be available. Please check http://www.microchip.com/ packaging for small-form factor package availability, or contact your local Sales Office. Microchip Devices Code Protection Feature Note the following details of the code protection feature on Microchip devices: * * * Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 753 PIC16(L)F18424/44 * * Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Legal Notice Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, KeeLoq logo, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, CryptoAuthentication, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 754 PIC16(L)F18424/44 All other trademarks mentioned herein are property of their respective companies. (c) 2018, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-5224-2698-1 Quality Management System Certified by DNV ISO/TS 16949 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California (R) (R) and India. The Company's quality system processes and procedures are for its PIC MCUs and dsPIC (R) DSCs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 755 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 Australia - Sydney Tel: 61-2-9868-6733 China - Beijing Tel: 86-10-8569-7000 China - Chengdu Tel: 86-28-8665-5511 China - Chongqing Tel: 86-23-8980-9588 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 China - Hong Kong SAR Tel: 852-2943-5100 China - Nanjing Tel: 86-25-8473-2460 China - Qingdao Tel: 86-532-8502-7355 China - Shanghai Tel: 86-21-3326-8000 China - Shenyang Tel: 86-24-2334-2829 China - Shenzhen Tel: 86-755-8864-2200 China - Suzhou Tel: 86-186-6233-1526 China - Wuhan Tel: 86-27-5980-5300 China - Xian Tel: 86-29-8833-7252 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 India - Bangalore Tel: 91-80-3090-4444 India - New Delhi Tel: 91-11-4160-8631 India - Pune Tel: 91-20-4121-0141 Japan - Osaka Tel: 81-6-6152-7160 Japan - Tokyo Tel: 81-3-6880- 3770 Korea - Daegu Tel: 82-53-744-4301 Korea - Seoul Tel: 82-2-554-7200 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 Malaysia - Penang Tel: 60-4-227-8870 Philippines - Manila Tel: 63-2-634-9065 Singapore Tel: 65-6334-8870 Taiwan - Hsin Chu Tel: 886-3-577-8366 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Thailand - Bangkok Tel: 66-2-694-1351 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Finland - Espoo Tel: 358-9-4520-820 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-67-3636 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra'anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7289-7561 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 (c) 2018 Microchip Technology Inc. Datasheet Preliminary DS40002000A-page 756