DVI-FPDLINKII-M/NOPB - TEXAS INSTRUMENTS

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

DVI - FPD LINK II (DS90UR905Q / 906Q)

Demo Platform User Guide

General Description

The DVI-FPD LINK II demo platform takes the DVI signals as a video input, and deserializes the parallel RGB and

control signals. The DS90UR905Q converts this 24-bit parallel RGB data and control data to a high-speed

serialized (FPD-LINK II) over a single pair with up to 10m STP cable. The DS90UR906Q recovers the data (RGB)

and control signals, and extracts the clock from the serial stream. The recovered RGB and control data are

converted back to the DVI signals as a video output to any Displays (See Figure 1).

Figure 1. Block Diagram

Ordering Information

Parts: DS90UR905Q & DS90UR906Q

Demo boards: DVI-FPDLINKII-M (Molex Cable)

DVI-FPDLINKII-R (Rosenberger / Leoni Cable)

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

Figure 2. Setup Diagram

Figure 3. Bottom Board

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

Figure 4. Top Board

Quick Start Guide

• The DVI – FPD Link II demo board consists of a “top board” and a “bottom” board

• The “Top board” has the DS 90UR905 and DS90UR906 devices

• The “Bottom board” has the TI DVI TX and RX devices

• Connect the included 12V AC/DC power adapter to the “CON3” of the top board

• Connect the PC (DVI Source) to DVI co nnector “CON1” (inputs to TI RX) of the bottom board

• Connect the LCD to DVI connector “CON2” (outputs from TI TX) of the bottom board

• On DVI-FPDLINKII-R board, connect the Rosen berger/Leoni cable between “CON4” (from 905 output)

and “CON5” (to 906 input) of the top board

• On DVI-FPDLINKII-M board, connect the Molex cable between “CON7” (from 905 output) and “CON8” (to

906 input) of the top board

• Three GREEN LEDs on the top board are ON and the picture should be seen on the LCD

D1 – “Lock” indication of TI DVI RX device

D3 – “Lock” indication of DS90UR906Q

D4 – “Pass” indication of DS90UR906Q

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

Other Optional Notes

• Bypass EEPROM

The resolution of video source is controlled by “EDID”. The EDID is provided by the display directly or

an EEPROM.

Configure Jumper “J4” and “J5” as shown in Figure 3.

1-2: EDID from EEPROM

2-3: EDID from Display (Default Setting)

• Long Cable Length

VODSEL and De-Emphasis controls – Turn both positions “ON” as shown in Figure 4 when longer

cable is used.

• SW6

Control switch of DS90UR905Q (refer to the datash eet).

• SW4 & SW5

Control switches of DS90UR906Q (refer to the d atasheet).

Bill of Materials

# Quat Reference Digikey PN Manufacture PN Descriptions

1 2 CON1,CON2 WM5601-ND 74320-4004 CONN RECEPT RT ANG DIGITAL DVI

2 1 CON3 CP-037BH-ND PJ-037BH CON PWR JACK 2.5 X 6.5MM

3 3 CON4,CON5,CON6 NA D4S20D-40ML5-Z HSD 2x2 MALE R/A

4 3 CON7,CON8,CON9 WM17535-ND 49616-0711 HDR USCAR MINI USB A R/A BLACK

5 1 CON10 CP1-3513SJCT-ND SJ1-3513-SMT CONN JACK STEREO 3POS 3.5MM

SMD

6 1 CON11 WM5461CT-ND 67503-1020 CONN RECEPT MINIUSB R/A 5POS

SMD

7 3 C1,C2,C110 495-2236-1-ND B45196H3106K109 CAP TANTALUM 10UF 16V 10% SMD

1206

8 39 C3,C4,C5,C6,C7,C8,C9,C10, PCC2336CT-ND ECJ-ZEB0J104M CAP CERAMIC .1UF 6.3V X5R 0201

C11,C12,C13,C29,C30,C33,

C34,C35,C36,C37,C43,C44,

C45,C46,

C51,C52,C53,C54,C55,C56,

C57,C76,C77,C78,C101,C116

C102,C103,C104,C105,C106

9 22 C14,C15,C16,C17,C18,C19, PCC2136CT-ND ECJ-ZEB0J103K CAP .01UF 6.3V CERAMIC X5R 0201

C20,C21,C22,C38,C39,C40,

C41,C42,C58,C59,C60,C61,

C62,C79,C80,C117

10 3 C89, C92 C94

0402ZD103KAT2A-

ND 0402ZD103KAT2A CAP CER 10000PF 10V X5R 0402

11 15 C70,C71,C72,C73,C74, PCC2364CT-ND ECJ-0EB1A105M CAP CERAMIC 1UF 10V X5R 0402

C75,C86,C87

C107,C108,C109,

C115,C118, C119

12 2 C26,C27 511-1498-1-ND TCTAL0J107M8R CAP TANTALUM 100UF 6.3V 20% SMD

1206

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

13 1 C23 1206ZD105MAT2A-

ND 1206ZD105MAT2A CAP CER 1.0UF 10V X5R 1206

14 2 C28,C95 511-1502-1-ND TCTAL1C226M8R CAP TANTALUM 22UF 16V 20% SMD

1206

15 2 C91,C97 587-1469-1-ND LMK325B7106MN-T CAP CER 10UF 10V X7R 1210

16 2 C98,C99 587-1387-1-ND

M

K325BJ107MM-T CAP CER 100UF 6.3V X5R 1210

17 2 C88,C93 490-3043-1-ND GRM31MR60J475KC11L CAP CER 4.7UF 6.3V 10% X5R 1206

18 1 C90 490-3161-1-ND GRM033R61A152KA01D CAP CER 1500PF 10V X5R 0201

19 1 C96 490-3163-1-ND GRM033R61A332KA01D CAP CER 3300PF 10V X5R 0201

20 25 R26,R27,R28,R29,R30,R31, DNI - SMD 0402

C82,R32,R33,R37,R39,

R41,R46,R48,R50,R53,R75,

R76,R77,R78,R79,R89,

R90,R91,R117

21 6 C31,C32,C47,C48,C49,C50 DNI - SMD 0201

23 1 C63 511-1443-1-ND TCP0J475M8R CAP TANT 4.7UF 6.3V 20% SMD 0805

24 1 C64 PCC2421CT-ND ECJ-0EB0J225M CAP CERAMIC 2.2UF 6.3V X5R 0402

25 2 C65,C66 445-4993-1-ND C1005X5R0J224K CAP CER .22UF 6.3V X5R 0402

26 3 C67,C68,C69 478-5526-1-ND TLNS227M004R3000 CAP TANT 220UF 4.0V SMD 1206

27 1 C81 PCC1748CT-ND ECJ-1VB1A154K CAP .15UF 10V CERAMIC X5R 0603

28 3 C83,C84,C85 587-1455-1-ND LMK105BJ474KV-F CAP CER .47UF 10V X5R 0402

29 2 C111,C112 399-3014-1-ND C0402C223K9PACTU CAP 22000PF 6.3V CERAM X5R 0402

30 2 C113,C114 04026D100JAT2A-

ND 04026D100JAT2A CAP CER 10PF 6.3V X5R 0402

31 3 D1,D3,D4 511-1592-1-ND SML-P12PTT86 LED GREEN 0.2MM 13MCD 0402 SMD

32 1 D2 511-1594-1-ND SML-P12VTT86 LED RED 0.2MM 60MCD 0402 SMD

33 4 D5,D6,D7,D8 160-1816-1-ND LTPL-P013WST1 LED 3 WATT COOL WHITE SMD

34 3 D9 568-4118-1-ND PMEG2020EH,115 SCHOTTKY RECT 20V 2A SOD123F

35 2 J1,J2 3M9465-ND 961240-6404-AR CONN HEADER VERT DUAL 40POS

GOLD

22 2 J8,J9 3M9531-ND 960240-6202-AR CONN SOCKET VERT DUAL 40POS

GOLD

36 1 J3 3M9463-ND 961224-6404-AR CONN HEADER VERT DUAL 24POS

GOLD

37 3 J4,J5,J14 WM6503-ND 22-28-4033 CONN HEADER 3POS .100 VERT

GOLD

38 1 J6 3M5473-ND 4808-3004-CP SOCKET IC OPEN FRAME 8POS .3"

39 3 J7,J11,J12 WM6502-ND 22-28-4023 CONN HEADER 2POS .100 VERT

GOLD

40 2 J10,J13 WM6504-ND 22-28-4043 CONN HEADER 4POS .100 VERT

GOLD

41 1 J15 WM26814-ND 10-89-7142 CONN HDR DUAL 14POS .100 SRT AU

42 1 J16 WM26808-ND 10-89-7082 CONN HDR DUAL 8POS .100 SRT AU

43 1 J17 WM26806-ND 10-89-7062 CONN HDR DUAL 6POS .100 SRT AU

44 1 L1 732-1258-1-ND 744773122 INDUCTOR POWER 22UH 1.0A SMD

45 34 R1,R2,R3,R4,R5,R6,R7,R8, RHM10.0KLCT-ND MCR01MZPF1002 RES 10.0K OHM 1/16W 1% 0402 SMD

R9,R10,R11,R15,R16,R18

R19,R20,R25,R52,R58,R60,

R61,R62,R63,R64,R65,R66,

R67,R68,R69,R70,R71,R72,

R73,R74

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

46 1 R17 RHM1.50KLCT-ND MCR01MZPF1501 RES 1.5K OHM 1/16W 1% 0402 SMD

47 1 R12 P510LCT-ND ERJ-2RKF5100X RES 510 OHM 1/10W 1% 0402 SMD

48 5 R13,R14,R34,R35,R36 RHM4.7KJCT-ND MCR01MZPJ472 RES 4.7K OHM 1/16W 5% 0402 SMD

49 1 R108 RHM1.50KLCT-ND MCR01MZPF1501 RES 1.50K OHM 1/16W 1% 0402 SMD

50 4 R21,R22,R23,R24 RHM220LCT-ND MCR01MZPF2200 RES 220 OHM 1/16W 1% 0402 SMD

51 17 R38,R40,R42,R43,R44,R45, P0.0JCT-ND ERJ-2GE0R00X RES 0.0 OHM 1/10W 5% 0402 SMD

R47,R49,R51,R54,R55,R56,

R109,R110,R111,R112,R118

52 2 R113,R114 P0.0ACT-ND ERJ-6GEY0R00V RES 0.0 OHM 1/8W 5% 0805 SMD

53 1 R57 P422LCT-ND ERJ-2RKF4220X RES 422 OHM 1/10W 1% 0402 SMD

54 1 R80 P61.9KLCT-ND ERJ-2RKF6192X RES 61.9K OHM 1/10W 1% 0402 SMD

55 3 R83 P1.54KLCT-ND ERJ-2RKF1541X RES 1.54K OHM 1/10W 1% 0402 SMD

56 1 R84 P536LCT-ND ERJ-2RKF5360X RES 536 OHM 1/10W 1% 0402 SMD

59 1 R92 HPC12100JCT-ND HPC 12 100 5% R RES 100 OHM 5W 5% SMD

60 1 R101 P1.00MLCT-ND ERJ-2RKF1004X RES 1.00M OHM 1/10W 1% 0402 SMD

61 4 R102,R103,R104,R105 P3.30KLCT-ND ERJ-2RKF3301X RES 3.30K OHM 1/10W 1% 0402 SMD

62 2 R107,R106 P16.0LCT-ND ERJ-2RKF16R0X RES 16.0 OHM 1/10W 1% 0402 SMD

63 1 R115 P12.0KLCT-ND ERJ-2RKF1202X RES 12.0K OHM 1/10W 1% 0402 SMD

64 1 R116 P5.60KLCT-ND ERJ-2RKF5601X RES 5.60K OHM 1/10W 1% 0402 SMD

65 2 R81,R82 P5.1KJCT-ND ERJ-2GEJ512X RES 5.1K OHM 1/10W 5% 0402 SMD

66 2 R85,R87 P1.00KLCT-ND ERJ-2RKF1001X RES 1.00K OHM 1/10W 1% 0402 SMD

67 1 R86 P2.32KLCT-ND ERJ-2RKF2321X RES 2.32K OHM 1/10W 1% 0402 SMD

68 1 R88 P806LCT-ND ERJ-2RKF8060X RES 806 OHM 1/10W 1% 0402 SMD

69 4 SW1,SW4,SW6,SW8 CT2196MST-ND 219-6MST SWITCH TAPE SEAL 6 POS SMD

70 1 SW2 CT2194MST-ND 219-4MST SWITCH TAPE SEAL 4 POS SMD

71 2 SW3,SW7 P12225SCT-ND EVQ-21505R SWITCH LT 6MM 160GF 5MM HEIGHT

72 1 SW5 CT2198MST-ND 219-8MST SWITCH TAPE SEAL 8 POS SMD

73 1 SW9 360-2131-ND CS12ANW03 SWITCH SLIDE SPDT 3A 125VAC PCB

74 1 U1 296-9992-ND TFP401PZP IC PANELBUS DVI REC 100-HTQFP

75 1 U2 296-12666-ND TFP410PAP IC TRANSMITTER DIGITAL 64-HTQFP

76 1 U3 NA DS90UR905Q IC SERIALIZER 48-LLP

77 1 U4 NA DS90UR906Q IC DESERIALIZER 60-LLP

78 1 U5 LM4934RLCT-ND LM4934RL IC AUDIO SUBSYSTEM 1.2W

42USMDXT

79 1 U6 296-15275-5-ND PCM2706PJT IC STEREO AUD DAC W/USB 32-TQFP

80 2 U7 LM22680MRE-

ADJCT-ND LM22680MRE-

ADJ/NOPB IC VREG SW STP-DWN 2A ADJ 8-

PSOP

81 1 U8,U9 LP3878MR-ADJ-

ND LP3878MR-ADJ/NOPB IC VREG 800MA ADJ 8-PSOP

82 1 U10 428-2188-5-ND CY2302SXI-1 IC CLK FREQ MULTI/ZDB 2OUT 8SOIC

83 1 X1 CTX410-ND ATS120 CRYSTAL 12.0000 MHZ SERIES RES

84 1 Y1 CTX303LVCT-ND CB3LV-3I-12M0000 OSC 12.0000 MHZ 3.3V SMD

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

Schematics

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

DVI – FPD LINK II Demo Platform User Guide Rev1.1

October 2010

Reference Layouts

Top layer

Bottom Board Top Board

Bottom layer

Bottom Board Top Board

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP®Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265