ATXMEGAE5-XPLD - Atmel - Datasheet.Live

AVR XMEGA Microcontrollers

AT02667: XMEGA-E5 Xplained Hardware User's

Guide

APPLICATION NOTE

Features

•Atmel® AVR® ATxmega32E5 microcontroller

•OLED display with 128×32 pixels resolution

•Ambient light sensor

•Analog filter

•Rotary Encoder with push button

•Digital I/O

–Two mechanical buttons

–Two user LEDs

–Four expansion headers

•Board controller with USB interface

–One power LED and one status LED

Description

The Atmel AVR XMEGA-E5 Xplained evaluation kit is a hardware platform to

evaluate the Atmel ATxmega32E5 microcontroller.

The kit offers a larger range of features that enables the Atmel AVR

XMEGA® user to get started using XMEGA peripherals right away and

understand how to integrate the XMEGA device in their own design.

Figure -1. XMEGA-E5 Xplained Kit

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

Table of Contents

Features.......................................................................................................................... 1

Description.......................................................................................................................1

1. Related Items.............................................................................................................3

2. General Information...................................................................................................4

2.1. Preprogrammed Firmware............................................................................................................4

2.2. Power Supply............................................................................................................................... 4

2.3. Measuring the Atmel AVR XMEGA Power Consumption............................................................. 4

2.4. Communication through the USART-to-USB Gateway................................................................ 5

2.5. Programming the Kit.....................................................................................................................5

3. Connectors................................................................................................................ 6

3.1. Programming Headers................................................................................................................. 6

3.2. I/O Expansion Headers................................................................................................................ 6

4. Peripherals.................................................................................................................9

4.1. Mechanical Buttons...................................................................................................................... 9

4.2. LEDs.............................................................................................................................................9

4.3. Quadrature Encoder.....................................................................................................................9

4.4. OLED Display.............................................................................................................................10

4.5. Analog I/O...................................................................................................................................10

4.5.1. Ambient Light Sensor.................................................................................................. 10

4.6. Board Controller..........................................................................................................................11

5. Code Examples....................................................................................................... 13

6. Hardware Revision History and Known Issues........................................................14

6.1. Revision 1...................................................................................................................................14

7. Document Revision History..................................................................................... 15

8. Evaluation Board/Kit Important Notice.....................................................................16

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

1. Related Items

The following list contains links to the most relevant documents, software and tools for the Atmel AVR

XMEGA-E5 Xplained:

•Atmel AVR Xplained products

Xplained is a series of small-sized and easy-to-use evaluation kits for 8- and 32-bit AVR

microcontrollers. It consists of a series of low cost MCU boards for evaluation and demonstration of

feature and capabilities of different MCU families.

•Atmel Xplained USB CDC driver

The Xplained USB CDC driver file supports both 32- and 64-bit versions of Windows® XP and

Windows 7. Driver installs are not necessary on Linux® operating systems.

•XMEGA-E5 Xplained schematics

Package containing schematics, BOM, assembly drawings, 3D plots, layer plots…

•AT02667: XMEGA-E5 Xplained Hardware Users Guide

This document.

•AT02657: XMEGA-E5 Xplained Software User Guide

This application note is a user guide for the XMEGA-E5 Xplained demo software.

•Atmel Studio 7

Atmel Studio 7 is a free Atmel IDE for development of C/C++ and assembler code for Atmel

microcontrollers.

•Atmel JTAGICE3

JTAGICE3 is a mid-range development tool for Atmel 8- and 32-bit AVR microcontrollers with on-

chip debugging for source level symbolic debugging, NanoTrace (if supported by the device) and

device programming.

•Atmel AVR JTAGICE mkII

AVR JTAGICE mkII is a mid-range development tool for Atmel 8- and 32-bit AVR devices with on-

chip debugging for source level symbolic debugging, NanoTrace (if supported by the device), and

device programming (superseded by JTAGICE3).

•Atmel AVR ONE!

AVR ONE! is a professional development tool for all Atmel 8- and 32-bit AVR devices with on-chip

debug capability. It is used for source level symbolic debugging, program trace, and device

programming. The AVR ONE! supports the complete development cycle and is the fastest

debugging tool offered from Atmel.

•Atmel AVR Dragon

AVR Dragon™ sets a new standard for low cost development tools for 8- and 32-bit AVR devices

with on-chip debug (OCD) capability.

•IAR Embedded Workbench® for Atmel AVR

IAR™ Embedded Workbench is a commercial C/C++ compiler that is available for 8-bit AVR. There

is a 30 day evaluation version as well as a 4k (code size limited) kick-start version available from

their website.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

2. General Information

The Atmel AVR XMEGA-E5 Xplained kit is intended to demonstrate the Atmel AVR ATxmega32E5

microcontroller. The figure below shows the available features on the board.

Figure 2-1. Overview of the XMEGA-E5 Xplained Kit

2.1. Preprogrammed Firmware

The ATxmega32E5 on the XMEGA-E5 Xplained is pre-programmed with a default firmware. The detailed

description of the software is available in the AT02657: XMEGA-E5 Xplained Software User Guide.

Project and source files are available in Atmel Studio and Atmel Software Framework.

2.2. Power Supply

The kit needs an external power supply that can deliver 5V and up to 500mA. The actual current

requirement for the board is much less than 500mA but in order to be able to power optional expansion

boards this margin is recommended.

The power can be applied to the board either via the USB connector or on pin 10 on header J3. The USB

connector is the preferred input because it is then possible to connect expansion boards on top of the J3

header.

The 5V (USB supply voltage) is regulated down to 3.3V with an onboard LDO regulator, which provides

power to the entire board. Expansion top boards that require 5V will get this from the header J3 pin 10.

2.3. Measuring the Atmel AVR XMEGA Power Consumption

As part of an evaluation of the Atmel AVR ATxmega32E5, it can be of interest to measure its power

consumption. Because the XMEGA has a separate power plane (VCC_MCU_P3V3) on this board it is

possible to measure the current consumption by measuring the current flowing into this plane. The

VCC_MCU_P3V3 plane is connected via a jumper to the main power plane (VCC_P3V3) and by

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

replacing this with an ampere meter it is possible to determine the current consumption. To locate the

power measurement header, refer to Figure 2-1.

Attention:

Do not power the board without having the jumper or an ampere meter mounted since this can

cause latch-up of the Atmel AVR ATxmega32E5 due to current flow into the I/O pins.

2.4. Communication through the USART-to-USB Gateway

The ATxmega32E5 USART is connected to a USART on the Atmel AT32UC3B1256. The ATxmega32E5

USART is communicating at 57600 baud using one start bit, eight data bits, one stop bit, and no parity.

When the AT32UC3B1256 device is enumerated (connected to a PC). The data transmitted from the

ATxmega32E5 is passed to a (virtual) COM port. This means that it is possible to use a terminal program

on a PC to receive the transmitted data. Similarly data transmitted from the PC COM port is passed to the

ATxmega32E5 USART through the gateway.

2.5. Programming the Kit

The kit can be programmed using an external programming tool.

How a programmer can be connected to the kit is described in Programming Headers.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

3. Connectors

The Atmel AVR XMEGA-E5 Xplained kit has four 10-pin 100mil headers, and one 6-pin 100mil header.

The 6-pin header is used for programming the Atmel AVR ATxmega32E5, and the 10-pin headers are

used to access spare analog and digital pins on the Atmel AVR XMEGA (expansion headers).

3.1. Programming Headers

The XMEGA can be programmed and debugged by connecting an external programming/debugging tool

to the PDI header shown in Figure 2-1.

The gray XMEGA PDI adapter must be used on the Atmel AVR JTAGICE mkII probe when connecting to

the XMEGA-E5 Xplained board.

The green standoff adaptor nr.3 (ref.A08-0254) has to be used on the Atmel AVR ONE! probe when

connecting to the XMEGA-E5 Xplained board.

Table 3-1. XMEGA Programming and Debugging Interface – PDI

Pin on programming header PDI

1 DATA

2 VCC

3 -

4 -

5 CLK

6 GND

3.2. I/O Expansion Headers

The Atmel AVR XMEGA-E5 Xplained headers J1, J2, J3, and J4 offer access to the I/Os of the

microcontroller in order to expand the board, for example by mounting a top module onto the board.

The header J1 offers digital communication interfaces like UART, TWI, and SPI. The table below shows

how the Atmel AVR XMEGA is connected to the header.

Note that when using TWI no pull-ups are mounted on the board from the factory, so it is required to

enable the internal pull-ups of the device.

Table 3-2. Expansion Header J1

Pin on J1 Name on J1 XMEGA pin Shared with on-board functionality

1 SDA PC0 Connected to the Board Controller 1

2 SCL PC1 Connected to the Board Controller 1

3 RXD PC2 -

4 TXD PC3 -

5 SS PC4 Connected to the Board Controller 2

1Need to mount R408/R409 to connect TWI lines to Board Controller.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

Pin on J1 Name on J1 XMEGA pin Shared with on-board functionality

6 MOSI PC7 Connected to the Board Controller 2

7 MISO PC6 Connected to the Board Controller 2

8 SCK PC5 Connected to the Board Controller 2

9 GND - -

10 VCC_P3V3 - -

Header J2 is connected to analog ports of the XMEGA as shown in the table below.

Table 3-3. Expansion Header J2

Pin on J2 Name on J2 XMEGA pin Shared with on-board functionality

1 ADC0 PA0 -

2 ADC1 PA1 -

3 ADC2 PA2 -

4 ADC3 PA3 -

5 ADC4 PA4 -

6 ADC5 PA5 Quadrature Encoder Button 3

7 ADC6 PA6 Quadrature Encoder Output 4

8 ADC7 PA7 Quadrature Encoder Output 4

9 GND - -

10 VCC_P3V3 - -

Header J3 is connected to digital ports of XMEGA. The table below shows the mapping of the XMEGA

I/O to J3.

Table 3-4. Expansion Header J3

Pin on J3 Name on J3 XMEGA pin Shared with on-board functionality

1 GPIO0 PR0 Shared with OLED display: data/cmd

function

2 GPIO1 PR1 Shared with OLED display: CS function

3 GPIO2 QENC_A Quadrature Encoder Output 5

4 GPIO3 QENC_B Quadrature Encoder Output 5

5 GPIO4 PC4/ SS

6 GPIO5 PC7/MOSI

2Need to mount R410/R411/R412/R413 to connect SPI lines to Board Controller.

3Can be disconnected from on-board functionality by cut-straps.

4Can be disconnected using SW103 mechanical switch.

5Quadrature encoder outputs can be accessible on this header when SW103 mechanical switch is

pushed up.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

Pin on J3 Name on J3 XMEGA pin Shared with on-board functionality

7 GPIO6 PC6/MISO

8 GPIO7 PC5/SCK

9 GND - -

10 VCC_P5V0 - -

Header J4 offers digital communication interfaces such as UART and TWI, but care must be taken

because some pins are also connected to on-board peripherals.

Table 3-5. Expansion Header J4

Pin on J4 Name on J4 XMEGA pin Shared with on-board functionality

1 SDA PD0 Shared with button SW100 (silkscreen

SW0)

2 SCL PD1 Shared with Light sensor 6

3 RXD PD2 Shared with button SW101(silkscreen

SW1)

4 TXD PD3 Shared with OLED display: reset

function

5 SS PD4 Shared with LED D100 (silkscreen

LED0)

6 MOSI PD7 Connected to the Board Controller 7

7 MISO PD6 Connected to the Board Controller 7

8 SCK PD5 Shared with LED D101 (silkscreen

LED1)

9 GND - -

10 VCC_P3V3 - -

6Can be disconnected from on-board functionality by cut-strap J100.

7RXD and TXD lines swapped from PD3 and PD4 and used for communication with board controller.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

4. Peripherals

4.1. Mechanical Buttons

Two mechanical buttons are connected to the Atmel AVR XMEGA. All buttons have no external pull-ups

so the user has to activate internal pull-ups in order to use them. When a button is pressed it will drive the

I/O line to GND.

Table 4-1. Mechanical Button Connection

Pin on XMEGA Silkscreen text on PCB

PD0 SW0

PD2 SW1

4.2. LEDs

There are two yellow LEDs available on the board that can be turned ON and OFF. The LEDs can be

activated by driving the connected I/O line to GND.

Table 4-2. LED Connections

Pin on XMEGA LED

PD4 Yellow LED0

PD5 Yellow LED1

One green LED (power indicator) and one red LED (status) are also present inside the same package

and therefore the colors can be mixed to orange when both are activated. The two LEDs are controlled

via the Board Controller and the user has no access to them.

4.3. Quadrature Encoder

The Quadrature Encoder (SW102) is made of one mechanical button and two outputs. These outputs are

connected to a mechanical switch (SW103), which enables to either connect them to the XMEGA pins or

let them be accessible on the J3 header.

Table 4-3. Quadrature Encoder Connections

Pin on XMEGA Pin on J3 header Switch SW103 Quadrature Encoder pins

PA5 8 NA NA 5 (button)

PA6 8NA 2-1 (switch pushed down) 1 (channel A)

PA7 8NA 5-4 (switch pushed down) 3 (channel B)

NA PIN3 2-3 (switch pushed up) 1 (channel A)

NA PIN4 5-6 (switch pushed up) 3 (channel B)

8Signal also connected to header J2.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

4.4. OLED Display

The OLED display on the XMEGA-E5 Xplained board is UG-2832HSWEG04 manufactured by WiseChip

Semiconductor Inc. It has a resolution of 128 × 32 pixels. In the design the display is connected via a SPI

based interface. Detailed information about the display can be obtained from the display datasheet.

The connection between the MCU and the OLED display is shown in the table below.

Table 4-4. OLED Display Connection

Pin on XMEGA Function on OLED

PR0 Data_command

PC5 SCK

PC7 MOSI

PC4 SS

PD3 RESET

4.5. Analog I/O

4.5.1. Ambient Light Sensor

The ambient light sensor TEMT6000X01 from Vishay Semiconductors is sensitive to visible light much

like the human eye. The measurement circuitry is configured to measure the illuminance from ~10 to

~900lx when the internal VCC/1.6 reference is used.

The data in Table 4-6 which shows the relationship between illuminance and output voltage of the sensor

circuitry is generated based on the symbols and formulas shown in the table below.

Table 4-5. Symbol Description for Illuminance Calculation

Symbols Description

ICA Calibrated sensor responsitivity at 100lx. This is 50μA according to the sensor

datasheet.

EvIlluminance

I Current through the sensor

U Output voltage of the sensor circuitry that is provided to the ADC

R Series resistor of the sensor circuitry. 4.7kΩ has been chosen in this design.

Ev = 100 × I / ICA Illuminance is calculated based on the relation of the actual current through the

sensor to the calibrated value at 100lx

I = U / R Since the ADC measures the voltage across the series resistor of the sensor

circuitry it is necessary to calculate the voltage based on the current

U = (Ev × R × ICA) / 100 Based on the current and the illuminance the output voltage of the sensor

circuitry can be calculated

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

Table 4-6. Illuminance vs. ADC Input Voltage

Illuminance [lux] ADC input [V] Illuminance

1 0.0024 Dusk

10 0.0235 Dusk

20 0.0470 Dusk

30 0.0705 Dusk

40 0.0940 Dusk

50 0.1175 Living room

60 0.1410 Living room

70 0.1645 Living room

80 0.1880 Living room

90 0.2115 Living room

100 0.2350 Living room

200 0.4700 Office lighting

300 0.7050 Office lighting

400 0.9400 Office lighting

500 1.1750 Office lighting

600 1.4100 Office lighting

700 1.6450 Office lighting

800 1.8800 Office lighting

900 2.1150 Office lighting

1000 2.3500 Overcast day

4.6. Board Controller

The Atmel AT32UC3B1256 board controller and the Atmel ATxmega32E5 are connected through TWI,

SPI, and USART interfaces. All interfaces can be used to communicate between the devices, but only the

USART is implemented by default on the board controller.

Table 4-7. ATxmega32E5 and Board Controller Communication Interface

Interface ATxmega32E5 pin Atmel AT32UC3B1256 pin

UART RX 9 PD6 PA24

UART TX 9PD7 PA23

TWI SCL 10 PC1 PA09

9This represents the RX and TX on the ATxmega32E5. The RX is connected to TX on the other

device, and vice versa.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

Interface ATxmega32E5 pin Atmel AT32UC3B1256 pin

TWI SDA 10 PC0 PA10

SPI SS 11 PC4 PA16

SPI MOSI 11 PC7 PA14

SPI MISO 11 PC6 PA25

SPI SCK 11 PC5 PA17

10 These TWI signals can be reconnected by placing a 0Ω resistor or a solder drop on R408 and R409

footprints.

11 These SPI signals can be reconnected by placing a 0Ω resistor or a solder drop on R410, R411,

R412, and R413 footprints.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

5. Code Examples

The example application is based on the Atmel AVR Software Framework that is included in Atmel Studio

6. The AVR Software Framework can also be found as a separate package online at:

http://www.atmel.com/tools/avrsoftwareframework.aspx.

For more information about the code example, see the application note Atmel AT02657 XMEGA-E5

Xplained Software Users Guide.

The Atmel AT32UC3B1256 board controller is also pre-programmed with a bootloader and a USART-to-

USB gateway application, which can be used to communicate with the target controller ATxmega32E5.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

6. Hardware Revision History and Known Issues

To identify the revision of the kit, locate the bar-code sticker on the back side of the board. The first line

on the sticker shows the product ID and the revision. For example “A09-1842/1” can be resolved to

ID=A09-1842 and revision=1.

6.1. Revision 1

Revision 1 of XMEGA-E5 Xplained is the initial released version, there are no known issues.

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

7. Document Revision History

Revision Date Changes

B 08/2016 Updated pictures

A 04/2013 Initial document release

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

8. Evaluation Board/Kit Important Notice

This evaluation board/kit is intended for use for FURTHER ENGINEERING, DEVELOPMENT,

DEMONSTRATION, OR EVALUATION PURPOSES ONLY. It is not a finished product and may not

(yet) comply with some or any technical or legal requirements that are applicable to finished products,

including, without limitation, directives regarding electromagnetic compatibility, recycling (WEEE), FCC,

CE or UL (except as may be otherwise noted on the board/kit). Atmel supplied this board/kit "AS IS",

without any warranties, with all faults, at the buyer's and further users' sole risk. The user assumes all

responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies Atmel

from all claims arising from the handling or use of the goods. Due to the open construction of the

product, it is the user's responsibility to take any and all appropriate precautions with regard to

electrostatic discharge and any other technical or legal concerns.

EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER USER NOR ATMEL

SHALL BE LIABLE TO EACH OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES.

No license is granted under any patent right or other intellectual property right of Atmel covering or

relating to any machine, process, or combination in which such Atmel products or services might be or

are used.

Mailing Address: Atmel Corporation

1600 Technology Drive

San Jose, CA 95110

USA

Atmel AT02667: XMEGA-E5 Xplained Hardware User's Guide [APPLICATION NOTE]

Atmel-42084B-XMEGA-E5-Xplained_AT02667_Application Note-08/2016

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com

Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, XMEGA®, and others are registered trademarks or trademarks of Atmel

Corporation in U.S. and other countries. Windows® is a registered trademark of Microsoft Corporation in U.S. and or other countries. Other terms and product names

may be trademarks of others.

DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any

intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND

CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED

OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,

CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS

INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this

document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to

update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive

applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any

applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without

an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the

operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments

unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically

designated by Atmel as automotive-grade.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Atmel:

ATXMEGAE5-XPLD