D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter PRODUCT OVERVIEW The D1U54P-W-1200-12-HxxPC series are very high efficiency 1200 watt, power factor corrected front end supply with a 12V main output and a 5V or 3.3V (3A) standby. They have active current sharing and up to 8 supplies may be operated in parallel. The supply may be hot plugged; recovers from overtemperature faults, and has status LEDs on the front panel in addition to logic and PMBusTM status signals. The low profile 1U package and >28W/cubic inch power density make it ideal for delivering reliable, efficient power to servers, workstations, storage systems and other 12V distributed power systems ORDERING GUIDE Part Number Power Output 200-240Vac 100-120Vac D1U54P-W-1200-12-HC4PC D1U54P-W-1200-12-HA4PC 1200W 1100W D1U54P-W-1200-12-HC3PC D1U54P-W-1200-12-HA3PC 1. Refer to Pg. 9 for alternate input connector (HAxPTC) FEATURES 1200W output power 80 PLUS(R) Platinum efficiency 12V main output 3.3V and 5V standby output 1U height: 2.15" x 12.65" x 1.57" >28 Watts per cubic inch density N+1 redundancy capable, including hot plugging (up to 8 in parallel) Active current sharing on 12V main output; both outputs contain ORing FET isolation Overvoltage, overcurrent, overtemperature protection Internal cooling fan (variable speed) PMBusTM / IC interface with status indicators RoHS compliant Two-year warranty www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html INPUT CHARACTERISTICS Parameter Input Voltage Operating Range Input Frequency Turn-on Input Voltage Turn-off Input Voltage Maximum current at Vin = 100Vac Inrush Current Power Factor Main Output Standby Output 12Vdc 3.3Vdc 5Vdc 3.3Vdc 5Vdc Conditions Ramp up Ramp down 1100W Cold start between 0 to 200msec At 230Vac, full load 20% load Efficiency (230Vac) excluding fan load 50% load (HCxPC models 80 PLUS(R) certified) 100% load Min. 90 47 80 65 Airflow Back to Front Front to Back Nom. 115/230 50/60 85 73 IEC 320-C16 Input Connector Option HA4PTC1 HA3PTC1 Max. 264 63 89 78 12 25 Units Vac Hz Vac Arms Apk 0.99 90 94 91 % OUTPUT VOLTAGE CHARACTERISTICS Nominal Output Parameter Conditions Min. Typ. Max. Units Voltage Nominal Output Voltage 12 Vdc Output Set Point Accuracy 50% load; Tamb =25C -0.5 +0.5 % Line and Load Regulation -1.0 +1.0 12V Ripple Voltage & Noise3 20MHz Bandwidth 150 mV p-p Output Current (230Vac) 5 100 A Output Current (120Vac) 5 90 Load Capacitance 0 30,000 F Nominal Output Voltage 3.3 Vdc Line and Load Regulation 3.14 3.46 3.3VSB Ripple Voltage & Noise3 20MHz Bandwidth 75 mV p-p Output Current 0 3 A Load Capacitance 0 1000 F Nominal Output Voltage 5.0 Vdc Line and Load Regulation 4.76 5.24 5VSB Ripple Voltage & Noise12 20MHz Bandwidth 75 mV p-p Output Current 0 3 A Load Capacitance 0 1000 F 3 Ripple and noise are measured with 0.1 F of ceramic capacitance and 10 F of tantalum capacitance on each of the power supply outputs. A short coaxial cable with 50 scope termination is used. Available now at: www.murata-ps.com/en/3d/acdc.html For full details go to www.murata-ps.com/rohs . www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 1 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CHARACTERISTICS Parameter Startup Time Transient Response Min. Typ. Max. 3 5 5 Units s % Current sharing accuracy (up to 8 in parallel)1 At 100% load 7 % Hot Swap Transients All outputs remain in regulation Full AC input range and 1200W total output power Full AC input range and 720W total output power 5 % Holdup Time ENVIRONMENTAL CHARACTERISTICS Parameter Storage Temperature Range Operating Temperature Range Operating Humidity Storage Humidity Altitude (without derating at 40C) Shock Operational Vibration MTBF Safety Approval Standards Conditions Noncondensing 12 ms 20 ms Min. -40 0 5 5 3000 Typ. Max. 70 60 90 95 Power Supply has internal 15A/250V fast blow fuse on the AC line input 2.43 lbs (1.10 kg) PROTECTION CHARACTERISTICS Output Voltage Parameter Overtemperature (intake) Overvoltage Overcurrent At 220Vac 12V Overcurrent At 110Vac4 Overvoltage 3.3VSB Overcurrent Overvoltage 5VSB Overcurrent Conditions Autorestart Latching Hiccup Hiccup Latching Hiccup Latching Hiccup Min. 70 13 105 99 3.6 3.3 5.4 3.3 Units C % m 30G non-operating Sine sweep; 5-150Hz, 2G; random vibration, 5-500Hz, 1.11G Per Telcordia SR-332 M1C1 @40C 529K CAN/CSA C22.2 No 60950-1-07, Amendment 1:2011, Amendment 2:2014 (MOD) ANSI/UL 60950-1-2014 IEC60950-1:2005 (2nd ED.)+A1:2009+A2:2013 EN60950-1:2006+A11+A1+A12+A2 CCC GB4943.1-2011, GB9254-2008, GB17625. 1-2012 BSMI CNS14336-1; CNS13438 Input Fuse Weight 4 Typ. hrs Max. 80 14 120 117 4.0 4.5 6.0 4.5 Units C V A A V A V A An output overload condition that caused the input current to exceed 13Aac shall initiate a latching shutdown. It will be necessary to recycle the ac input source in order to clear the latched condition. ISOLATION CHARACTERISTICS Parameter Insulation Safety Rating / Test Voltage Isolation . Conditions AC ramp up 12V, 50% load step, 1A/s di/dt VSB, 50% load step, 1A/s di/dt Conditions Input to Output - Reinforced Input to Chassis - Basic Output to Chassis Min. 3000 1500 500 Typ. Max. Units Vrms Vrms Vdc www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 2 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter STATUS INDICATORS AND CONTROL SIGNALS GREEN AMBER Condition LED Status (Power) LED Status (Fault) Standby - ON; Main output - OFF; AC PRESENT Standby - ON; Main output - ON Main output overcurrent, undervoltage, overvoltage FAN_FAULT; overtemperature; standby overcurrent, undervoltage No AC Power Power Supply Warning Event Blinking green Solid green Off Off Off Off Off Off On On Off Blinking STATUS AND CONTROL SIGNALS I/O Signal Name ACOK (AC Source) PWOK (Output OK) SMB_ALERT (FAULT/ WARNING) PRESENT_L (Power Supply Absent) PS_ON (Power Supply Enable/Disable PSKILL APS (Address Select) SCL (Serial Clock) SDA (Serial Data) Description Interface Details Output The signal output is driven high when input source is available and within acceptable limits. The output is driven low to indicate loss of input power. Pulled up internally via 10K to VDD4 A logic high >2.0Vdc A logic low <0.8Vdc Driven low by internal CMOS buffer (open drain output). Output The signal is asserted, driven high, by the power supply to indicate that all outputs are valid. If any of the outputs fail then this output will be hi-Z or driven low. The output is driven low to indicate that the Main output is outside of lower limit of regulation (11.4Vdc). Pulled up internally via 10K to VDD4 A logic high >2.0Vdc A logic low <0.8Vdc Driven low by internal CMOS buffer (open drain output). Output The signal output is driven low to indicate that the power supply has detected a warning or fault and is intended to alert the system. This output must be driven high when the power is operating correctly (within specified limits). The signal will revert to a high level when the warning/fault stimulus (that caused the alert) is removed. Pulled up internally via 10K to VDD4 A logic high >2.0Vdc A logic low <0.8Vdc Driven low by internal CMOS buffer (open drain output). Output The signal is used to detect the presence (installed) of a PSU by the host system. The signal is connected to PSU logic SGND within the power module. Passive connection to +VSB_Return. A logic low <0.8Vdc Input This signal is pulled up internally to the internal housekeeping supply (within the power supply). The power supply main 12Vdc output will be enabled when this signal is pulled low to +VSB_Return. In the low state the signal input shall not source more than 1mA of current. The 12Vdc output will be disabled when the input is driven higher than 2.4V, or open circuited. Cycling this signal shall clear latched fault conditions. Pulled up internally via 10K to VDD4 Input This signal is used during hot swap to disable the main output during hot swap extraction. The input is pulled up internally to the internal housekeeping supply (within the power supply). The signal is provided on a short (lagging pin) and should be connected to +VSB_ Return. A logic high >2.0Vdc An analog input that is used to set the address of the internal slave devices (EEPROM and microprocessor) used for digital communications. Connection of a suitable resistor, to +VSB_Return, in conjunction with an internal resistor divider chain, will configure the required address. DC voltage between the limits of 0 and VDD4 Both A serial clock line compatible with PMBusTM Power Systems Management Protocol Part 1 - General Requirements Rev 1.1. No additional internal capacitance is added that would affect the speed of the bus. The signal is provided with a series isolator device to disconnect the internal power supply bus in the event that the power module is unpowered. VIL is 0.8V maximum VOL is 0.4V maximum when sinking 3mA VIH is 2.1V minimum Both A serial data line compatible with PMBusTM Power Systems Management Protocol Part 1 - General Requirements Rev 1.1. The signal is provided with a series isolator device to disconnect the internal power supply bus in the event that the power module is unpowered. VIL is 0.8V maximum VOL is 0.4V maximum when sinking 3mA VIH is 2.1V minimum Input 4 VDD is an internal voltage rail derived from VSB and an internal housekeeping rail ("diode ORed" together) and is compatible with the voltage tolerances of VSB). . www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 3 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter STATUS AND CONTROL SIGNALS CONTINUED V1_SENSE V1SENSE_RTN Input ISHARE Bi-Directional Analogue Bus Remote sense connections intended to be connected at and sense the voltage at the point of load. The voltage sense will interact with the internal module regulation loop to compensate for voltage drops due to connection resistance between the output connector and the load. If remote sense compensation is not required then the voltage can be configured for local sense by: V1_SENSE directly connected to power blades 6 to 10 (inclusive) V1_SENSE_RTN directly connected to power blades 1 to 5 (inclusive) The current sharing signal is connected between sharing units (forming an ISHARE bus). It is an input and/or an output (bi-directional analog bus) as the voltage on the line controls the current share between sharing units. A power supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit the voltage on the pin (and the common ISHARE bus would read approximately 8VDC at 100% load (module capability). For two identical units sharing the same 100% load this would read approximately 4VDC for perfect current sharing (i.e. 50% module load capability per unit). Compensation for up to 0.12Vdc total connection drop (output and return connections). Analogue voltage: +8V maximum; 4K to +12V_RTN TIMING SPECIFICATIONS Turn-On Delay & Output Rise Time: Power On Delay; Rise Time and Signaling V1 PS_ON Delay AC Input AC Input VSB VSB VSB Rise Time VSB Power On Delay V1 Rise Time V1; 12V V1; 12V V1 PS_ON Delay V1 Power On Delay PS_ON AC_OK PS_ON AC_OK Delay AC_OK PW_OK Delay PW_OK PW_OK 1. The turn-on delay after application of AC input within the operating range shall as defined in the following tables. 2. The output rise times shall be measured from 10% of the nominal output to the lower limit of the regulation band as defined in the following tables. Time Vsb Power-on-delay Vsb Rise time V1 Rise time V1 Power-on-delay V1 PS_ON delay V1 PWOK delay ACOK detect . Min 40ms 2ms 2ms 100ms 500ms Max 2700ms 100mS 10ms 3000ms 20ms 300ms 2500ms www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 4 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter TIMING SPECIFICATIONS Turn-Off (Shutdown by PS_ON) Turn Off Fall Time and Signaling AC Input Turn-Off Timing V1 Fall time V1 PS_OFF delay PW_OK delay off VSB Min 0ms 1.0ms Max 5ms Notes Must be monotonic V1; 12V V1 PS_OFF Delay V1 Falltime PS_ON AC_OK PWOK delayoff PW_OK 1. Note this characteristic is applicable for the main 12Vdc output shutdown from PS_ON pulled high. Power Removal Holdup Power Removal Timing Vsb holdup V1 holdup (Effective Total) AC fail detect PWOK delay off PWOK Hold Up EMISSIONS AND IMMUNITY Characteristic Input Current Harmonics Voltage Fluctuation and Flicker Conducted Emissions ESD Immunity Radiated Field Immunity Electrical Fast Transients/Burst I it Surge Immunity . Min 40ms 12ms 1.0ms 11.0ms Max 40ms Notes 100% load 100% load 100% load RF Conducted Immunity Magnetic Field Immunity Standard IEC/EN 61000-3-2 IEC/EN 61000-3-3 FCC 47 CFR Part 15/CISPR 22/EN55022 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 Compliance Complies Complies Class A with 6dB margin Level 4 criteria A Level 3 criteria B Level 3 criteria B Level 3 criteria A Level 3 criteria A 3 A/m criteria B Voltage Dips, Interruptions IEC/EN 61000-4-11 230Vin, 100% load, Phase 0, Dip 100% Duration 10ms (A) 230Vin, 50% load, Phase 0, Dip 100% Duration 20ms (VSB:A, V1:B) 230Vin, 100% load, Phase 0, Dip 100% Duration > 20ms (VSB, V1:B) www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 5 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter DERATING CURVES Main Output current (Adc) Output Current Derating vs Ambient Temperature (back to front airflow) D1U54P-W-1200-12-Hx4PC 110 100 90 80 70 60 50 40 30 20 10 0 90 Vac 115 Vac 120 Vac 180 Vac 25 30 35 40 45 50 55 60 Ambient Temperature ( C) Output Current Derating vs Ambient Temperature (back to front airflow) D1U54P-W-1200 -12- HA4PTC (with C16 AC Input Connector) 105 Main Output current (Adc) 100 95 90 85 90 Vac 80 115 Vac 75 120 Vac 70 180 Vac 65 60 25 30 35 40 45 50 55 60 Ambient Temperature ( C) Output Current Derating vs Ambient Temperature (front to back airflow) All Models 105 Main Output current (Adc) 100 95 90 85 90 Vac 80 115 Vac 75 120 Vac 70 180 Vac 65 60 25 30 35 40 45 50 55 60 Ambient Temperature ( C) . www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 6 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter OUTPUT CONNECTOR AND SIGNAL SPECIFICATION E1 E2 E3 E4 E5 D1 D2 D3 D4 D5 C1 C2 C3 C4 C5 B1 B2 B3 B4 B5 A1 A2 A3 A4 A5 1 2 3 4 5 6 7 8 9 10 PIN ASSIGNMENTS - D1U54P-W-1200-12-HxxPC Tyco PN 1926734-2 (Power Supply) Pin Signal Name Comments + 12V main output 6, 7, 8, 9, 10 V1 + 12V main output return 1, 2, 3, 4, 5 PGND Standby output A1 VSB Standby output B1 VSB Standby output C1 VSB Standby output D1 VSB Standby output E1 VSB Standby return A2 VSB_return Standby return B2 VSB_return C2 unused D2 unused E2 unused I2C address and protocol selection, A3 APS (select by a pull down resistor) B3 unused I2C data signal line C3 SDA - Remote Sense return D3 V1_SENSE_R + Remote Sense E3 V1_SENSE I2C clock signal line A4 SCL Remote On/Off B4 PS_ON I2C alert signal C4 SMB_ALERT D4 unused AC input OK E4 ACOK Power supply kill, short pin A5 PSKILL Current share bus, short pin B5 ISHARE Power OK, short pin C5 PWOK D5 unused Power supply present, short pin E5 PRESENT_L MATING CONNECTOR . Part Number Description Tyco Electronics 2-1926739-5 Right Angle www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 7 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter WIRING DIAGRAM FOR OUTPUT Dotted lines show optional remote sense connections. Optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. V1_SENSE (Main Output Remote Sense) V1_SENSE (Main Output Remote Sense) +12V main output E3 +12V main output 6-10 E3 6-10 D1U54P D1U54P 12V load 1-5 D3 B5 (or D4) A1,B1,C1,D1,E1 V1_SENSE_R V1_SENSE_R D3 ISHARE ISHARE VSB VSB B4 PS_ON A2,B2 A5 (or A3) +12V main output return 1-5 +12V main output return VSB_return PS_KILL A1,B1,C1,D1,E1 PS_ON B4 VSB load FET, BJT, wire or switch (debounced ) to turn on +12V main output B5 (or D4) VSB_return A2,B2 PS_KILLA5 (or A3) CURRENT SHARING NOTES 1. Main Output current sharing is achieved using the active current share method. (See wiring diagram for connection details.) Current sharing can be achieved with or without remote sense connected to the common load. 2. 3. 4. 5. . +VSB outputs can be tied together for redundancy but total combined output power must not exceed the rated standby power. The +VSB output has internal ORing MOSFET for additional redundancy / internal short protection. The current share pin B5 (or D4 for alternate pin out model) is a connection between the units. It is input and/or output as the voltage on the line controls the current share. A power supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit this would read approximately 8V at 100% load. For two units sharing load then this should read approximately 4V for perfect current sharing. Up to 8 units can be paralleled together. Please consult your Murata sales representative if operation with more than 8 units in parallel is needed. The load for both the main 12V and the VSB rails at initial startup shall not be allowed to exceed the capability of a single unit. The load can be increased after a delay of 3sec (minimum), to allow all sharing units to achieve steady state regulation. www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 8 of 9 D1U54P-W-1200-12-HxxPC Series 54mm 1U Front End AC-DC Power Supply Converter MECHANICAL DIMENSIONS Airflow Direction: Hx3PC Hx4PC AC input connector: IEC 320-C14 Alternate input connector: IEC 320-C16 (for HAxPTC models); Link back to front page Dimensions: 2.15" x 12.657" x 1.575" [54.5mm x 322.0mm x 40.0mm] Reference file: I:\Eng_wip\UserPDDwg\1728\D1U54P-1200 dated 9/21/2018 Latch: 1) when latch is not pressed, Latch front edge below PSU body surface. 2) Latch can fully go inside PSU body surface when handle is pressed down. MECHANICAL DIMENSIONS OPTIONAL ACCESSORIES Description Part Number 12V D1U54P Output Connector Card D1U54P-12-CONC APPLICATION NOTES Document Number Description Link ACAN-44 D1U54P Output Connector Card www.murata-ps.com/data/apnotes/acan-44.pdf ACAN-45 D1U54P-x Communication Protocol www.murata-ps.com/data/apnotes/acan-45.pdf This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2018 Murata Power Solutions, Inc. . www.murata-ps.com/support D1U54P-W-1200-12-HxxPC.B05 Page 9 of 9