The engineer’s choice
version 2013-05
EC/AC centrifugal fans RadiCal
2
EC/AC centrifugal fans – RadiCal
This opens up entirely new possibilities for applications in ventilation and
air-conditioning and beyond. For example, ebm-papst AC fans can now be
replaced by the latest fans in GreenTech EC technology without any
expensive modification.
Advantages at a glance:
– High efficiency with improved impeller technology and new EC motors
– Perfectly matching components (controller/motor/impeller)
– Extremely quietly running with optimised air flow through the impeller
– Significantly reduced tonal noise
– Unrivalled compactness
– Mechanical compatibility of AC and EC fans
– EC fans with 2 speeds or continuous control
– High power density
– Robust design and maintenance-free operation
– Easy initial set-up
– ErP* compliant (see individual designation)
*ErP: Energy-related Products directive – defined minimum requirements
for fans in accordance with the EcoDesign directive for fans with a
drive output of 125 W and above.
Impellers made of high-tech compound material with optimised flow con-
trol, combined with proven single- or 3-phase asynchronous motors or
highly efficient GreenTech EC motors: these are the outstanding features
of the new generation of backward-curved centrifugal fans for operation
without scroll housing. That's RadiCal!
The impellers in sizes 133 to 630mm are made of a single-piece special
compound material which allows for high rotational speed, and thus for
the high power density of the fan. The impeller styling has been optimised
using complex simulation models adjusted to perfection by checking
against prototypes. The result is an optimal, low-loss flow of air through
the impeller and so there are no longer any drastic cross-sectional chan-
ges, a well-known source of losses in the impeller. A uniform flow profile
without separations also means fewer noise sources and thus better
acoustics. That's RadiCal, too!
The new motor in GreenTech EC technology with integrated control elec-
tronics is designed in such as way as to make the RadiCal fans in sizes
190 up to 250mm have the same mounting dimensions as the combina-
tion of the same impeller with an asynchronous motor. In addition, the
specified EC centrifugal fan achieves significantly higher air performance
than the AC variant with identical dimensions. The small GreenTech EC
fans are available in two different control configurations: one with two
fixed speed stages and another with the familiar continuous control option
via a combined 0-10V/PWM control input. Sizes exceeding 250mm can be
controlled by a 0-10V/PWM input signal or monitored respectively control-
led via RS485 serial connection, using the MODBUS-RTU protocol.
3
EC/AC centrifugal fans - RadiCal 2
GreenTech: The Green Company 4
EC centrifugal fans - RadiCal Ø 133-630 7
AC centrifugal fans - RadiCal Ø 133-630 101
Accessories 158
Electrical connections 163
Technical parameters & scope 172
ebm-papst representatives & subsidiaries 176
Table of contents
4
Sustainability is at the centre of our
thoughts and actions. Out of conviction!
GreenTech is pro-active development.
Even in the design phase, the materials and processes we use are optimi-
sed for the greatest possible eco-friendliness, energy balance and –
wherever possible – recyclability. We continually improve the material
and performance of our products, as well as the flow and noise charac-
teristics. At the same time, we significantly reduce energy consumption.
Close co-operation with universities and scientific institutes and the pro-
fessorship we endow in the area of power engineering and regenerative
energies allows us to profit from the latest research findings in these
fields – and at the same time ensure highly qualified young academics.
GreenTech is eco-friendly production.
GreenTech also stands for maximum energy efficiency in our production
processes. There, the intelligent use of industrial waste heat and ground-
water cooling, photovoltaics and, of course, our own cooling and venti-
lation technology are of the utmost importance. Our most modern plant,
for instance, consumes 91% less energy than currently specified and
required. In this way, our products contribute to protecting the environ-
ment, from their origin to their recyclable packaging.
GreenTech is acknowledged and certified.
Every step in our chain of production meets the stringent standards of
environmental specialists and the public. The Deutscher Nachhaltigkeits-
preis 2012 (German Sustainability Award 2012), where we were given the
Top3-award in the category “Germany’s most sustainable strategy for the
future (company group)” bears testimony to our commitment to sustainabi-
lity, as does the DEKRA Award 2012 we received in the category “Umwelt –
Herausforderung Energiewende / Environment – Challenge: Transition to
more sustainable energy systems”, to name only a few of a large number
of examples. The environmental advantage gained in the performance of
the products developed from our GreenTech philosophy can also be mea-
sured in the fulfillment of the most stringent energy and environmental
standards. In many instances, our products are already well below the
thresholds energy legislation will impose a few years from now – several
times over.
Our customers profit from this every day.
The heart of GreenTech is future-oriented EC technology from ebm-
papst. The EC technology at the core of our most efficient motors and
fans allows efficiency of up to 90%, saves energy at a very high level,
significantly extends service life and makes our products maintenance-
free. These values pay off not only for the environment, but every cent al-
so pays off for the user! All ebm-papst products – even those for which
GreenTech EC technology does not (yet) make sense from an application
viewpoint – feature the greatest possible connection of economy and
ecology.
Eco-friendliness and sustainability have always been at the core of
our thoughts and actions. For decades, we have worked according
to the simple but strict creed of our co-founder Gerhard Sturm:
“Each new product we develop has to be better than the last one in
terms of economy and ecology. GreenTech is the ultimate expres-
sion of our corporate philosophy.
Philosophy
Awards
Application
Development
Production
5
6
7
EC centrifugal fans – RadiCal
40 80 120 160 200 240
0 20 12040 60 100 140 160
40
80
120
160
240
280
320
360
400
0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6
1
2
3
4
200
80 cfm
qV
pfs Pa
in H2O
m3/h
Material: Housing: PA plastic 6, fibreglass-reinforced
Impeller: PA plastic 6, fibreglass-reinforced
Rotor: Thick layer passivated
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B"
Mounting position: Any
Condensate discharges: None, open rotor
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
n
rpm
Ped
W
I
A
A
LWA
dB(A)
8
EC centrifugal fans – RadiCal
backward curved, Ø 133
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
Speed-controlled
A
A
A
Nominal data
Type Motor
*3G 133 M3G 045-AI
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A °C
1~ 200-240 50/60 3770 27 0,27 -25..+60
Curve
p. 165 / H4)
Technical features
and electrical
connection
A
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
= max.
3η
A
1
2
3
4
3930
3800
3770
3835
24
26
27
26
0,23
0,26
0,27
0,25
66
63
61
65
Technical features: See electrical connections p. 165
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
9
Inlet nozzle
p. 158
Guard grille
p. 160
Electr. connection
p. 165
Centrifugal fan
R3G 133-RA01 -03
kg
0,5 K3G 133-RA01 -03
Mass of
centrifugal fan
kg
0,75
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
Drawings
p. 10
2
Ø58±0.2
Ø27
685
±10
450
+20
4
48.5
Ø89
Ø93±0.2
57.3
63±1
Ø129
Ø118
Ø87
13
1
Ø4.5 (4x)
4x90˚
M4 (4x)
Ø133
10
EC centrifugal fans – RadiCal
backward curved, Ø 133, speed-controlled
R3G 133-RA01-03 (Centrifugal fan)
K3G 133-RA01-03 (Centrifugal module with support basket)
Ø210
Ø195±0.5
Ø195±0.5
Ø180
±0.5
Ø27
45°
o
165
2
64
6
6
85±10
450+20
o
147±0.5
Ø5 (4x)
Connection line AWG 20,
3 x brass lead tips crimped
Control line AWG 22,
4 x brass lead tips crimped
Mounting
dimensions:
Depth of screw max. 5 mm
Accessory part:
Inlet nozzle 09566-2-4013
not included in the standard
scope of delivery
11
200 400 600 800
0 400100 200 300 500
600
0,8 2,4
800
3,2
1000
4,0
155 1
2
6
7
8
3
4
3
4
2
200
1,6
400
6
7
8
cfm
qV
pfs Pa
in H2O
m3/h
A
B
12
*3G 190 M3G 055-BD 1~ 200-240 50/60 2710 57 0,43 -25..+60 p. 164 / H3)
*3G 190 M3G 055-CF 1~ 200-240 50/60 4120 169 1,35 -25..+60 p. 164 / H3)
B
*3G 190 M3G 055-BI 1~ 200-240 50/60 3200 83 0,75 -25..+60 p. 165 / H4)
C
*3G 190 M3G 055-CF 1~ 200-240 50/60 3640 115 1,10 -25..+60 p. 163 / H5)
D
A
Ped
W
I
A
A
LWA
dB(A)
Curves:
2 Speed stages
A
A
A
= max.
7η
1
2
3
4
5
6
7
8
A
A
A
A
1
2
3
4
5
6
7
8
B
B
B
B
B
B
B
B
2880
2815
2710
2780
2435
2390
2325
2360
4440
4235
4120
4155
3720
3675
3615
3650
49
52
57
54
30
32
35
33
160
165
169
160
95
105
115
110
0,36
0,40
0,43
0,41
0,23
0,25
0,27
0,26
1,35
1,35
1,35
1,35
0,85
0,95
1,00
0,95
69
64
62
67
65
60
59
63
81
75
72
74
77
73
69
72
3
*3G 190 M3G 055-CF 1~ 200-240 50/60 4120 169 1,35 -25..+60 p. 165 / H4)
E
EC centrifugal fans – RadiCal
backward curved, Ø 190
Material: Housing: PA plastic 6, fibreglass-reinforced
Impeller: PA plastic 6, fibreglass-reinforced
Rotor: Thick layer passivated
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B"
Mounting position: Any
Condensate discharges: None, open rotor
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
13
Technical features: See electrical connections p. 163 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
R3G 190-RB01 -01 0,85 K3G 190-RB01 -01 1,40
R3G 190-RD45 -01 1,36 K3G 190-RD45 -01 1,91
R3G 190-RC05 -03 1,06 K3G 190-RC05 -03 1,61
R3G 190-RG19 -01 1,40 K3G 190-RG19 -01 1,60
kg kg
Guard grille
p. 160
Electr. connection
p. 163 ff.
200 400 600 800
0 400100 200 300 500
600
0,8 2,4
800
3,2
1000
4,0
1
1 1
2
3
4
3
3
4
4
22
200
1,6
400
cfm
qV
pfs Pa
in H2O
m3/h
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
3435
3335
3200
3300
3980
3865
3640
3840
4440
4235
4120
4155
80
83
83
83
115
115
115
115
160
165
169
160
0,69
0,73
0,75
0,74
1,10
1,10
1,10
1,10
1,35
1,35
1,35
1,35
73
68
66
70
78
74
71
76
81
75
72
74
E
C
Curves:
Speed-controlled = max.
3η
n
rpm
Ped
W
I
A
LWA
dB(A)
Inlet nozzle
p. 158
Drawings
p. 14 ff.
R3G 190-RD45 -03 1,36 K3G 190-RD45 -03 1,91
D
1
2
3
4
E
E
E
E
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
14
R3G 190-RB01-01 (Centrifugal fan)
K3G 190-RB01-01 (Centrifugal module with support basket)
2
Ø72
2
Ø80
Ø27
Ø190
Ø132.8±0.2
68.5±1
62.5
Ø89
Ø4.5 (4x)
Ø125.5
Ø158
Ø170
1.25
14
450+20
85±10
6
Ø58±0.2
M4 (4x)
450
+20
85
±10
6
Ø244
Ø265±0.5
Ø5 (4x)
o
225 79
6
45°
o
204±0.5
Ø265
±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 09576-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 190, 2 speed stages, 85 W - electronics
15
R3G 190-RD45-01 (Centrifugal fan)
K3G 190-RD45-01 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø190
Ø132.8±0.2
88±1
62.5
Ø101
Ø4.5 (4x)
Ø125.5
Ø158
Ø170
1.25
14
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø244
Ø265±0.5
Ø5 (4x)
o
225
45°
o
204±0.5
Ø265±0.5
79
6
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 09576-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 190, 2 speed stages, 170 W - electronics
16
R3G 190-RC05-03 (Centrifugal fan)
K3G 190-RC05-03 (Centrifugal module with support basket)
85±10
450+20
6
2
Ø72
2
Ø80
Ø27
Ø190
Ø132.8±0.2
68.5±1
62.5
Ø89
Ø4.5 (4x)
Ø125.5
Ø158
Ø170
1.25
14
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø244
Ø265±0.5
Ø5 (4x)
o
225 79
6
45°
o
204±0.5
Ø265±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
3 x brass lead tips crimped
Accessory part:
Inlet nozzle 09576-2-4013
not included in the standard
scope of delivery
Control line AWG 22,
4 x brass lead tips crimped
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 190, speed-controlled, 85 W - electronics
17
R3G 190-RG19-01 (Centrifugal fan)
K3G 190-RG19-01 (Centrifugal module with support basket)
58
105
85
6
450+20
max.Ø95
Ø115
62.5
69
95
Ø132.8
Ø190
Ø125.5
Ø158
Ø170
1.25
14
R10
Ø4.5 (4x)
M4 (4x)
M4 (4x)
±1
±10
±0.2
±0.2
2
Ø
266
Ø244
204
45°
±0.5
±0.5
±0.5
225
Ø5 (4x) 6
85.5
107.5
Ø266
±0.5
450
85
6
±10
+20
Connection line PVC 4X 0.25 mm2,
4 x brass lead tips crimped
Connection line PVC 3G 0.5 mm2,
3 x brass lead tips crimped
Depth of screw max. 6 mm
Accessory part:
Inlet nozzle 09576-2-4013
not included in the standard scope
of delivery
Depth of screw max. 6 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 190, speed-controlled, 115 W - electronics
18
R3G 190-RD45-03 (Centrifugal fan)
K3G 190-RD45-03 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø190
Ø132.8±0.2
88±1
62.5
Ø101
Ø4.5 (4x)
Ø125.5
Ø158
Ø170
1.25
14
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø244
Ø265±0.5
Ø5 (4x)
o
225 79
6
45°
o
204±0.5
Ø265±0.5
Connection line AWG 20,
3 x brass lead tips crimped
Control line AWG 22,
4 x brass lead tips crimped
Depth of screw max. 5 mm
Accessory part:
Inlet nozzle 09576-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 190, speed-controlled, 170 W - electronics
19
200 400 600 800 1000 1200
0 400100 200 300 700600500
600
0,8 2,4
800
3,2
155 1
2
3
4
6
7
8
6
7
8
3
4
2
200
1,6
400
cfm
qV
pfs Pa
in H2O
m3/h
A
B
20
*3G 220 M3G 055-BI 1~ 200-240 50/60 2580 85 0,70 -25..+60 p. 164 / H3)
*3G 220 M3G 055-CF 1~ 200-240 50/60 3230 168 1,40 -25..+50 p. 164 / H3)
*3G 220 M3G 055-BI 1~ 200-240 50/60 2580 85 0,70 -25..+60 p. 165 / H4)
*3G 220 M3G 055-CF 1~ 200-240 50/60 2790 115 1,10 -25..+50 p. 163 / H5)
B
C
D
A
Ped
W
I
A
A
LWA
dB(A)
Curves:
2 Speed stages
A
A
A
= max.
7η
1
2
3
4
5
6
7
8
A
A
A
A
1
2
3
4
5
6
7
8
B
B
B
B
B
B
B
B
3
2765
2700
2580
2630
1505
1485
1470
1485
3540
3370
3230
3310
3000
2955
2900
2930
79
85
85
85
16
16
17
17
168
168
168
168
100
110
120
115
0,67
0,69
0,70
0,70
0,18
0,20
0,21
0,19
1,40
1,40
1,40
1,40
0,85
0,95
1,00
0,97
71
67
65
66
57
54
51
52
77
73
70
72
74
70
68
70
*3G 220 M3G 055-CF 1~ 200-240 50/60 3230 168 1,40 -25..+50 p. 165 / H4)
E
EC centrifugal fans – RadiCal
backward curved, Ø 220
Material: Housing: PA plastic 6, fibreglass-reinforced
Impeller: PA plastic 6, fibreglass-reinforced
Rotor: Thick layer passivated
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B"
Mounting position: Any
Condensate discharges: None, open rotor
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
200 400 600 800 1000
1200
0 400100 200 300 700600500
600
0,8 2,4
800
3,2
1
1 1
2
3
4
3
3
4
4
22
200
1,6
400
cfm
qV
pfs Pa
in H2O
m3/h
E
C
21
Technical features: See electrical connections p. 163 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
R3G 220-RC05 -01 1,13 K3G 220-RC05 -01 2,03
R3G 220-RD53 -01 1,53 K3G 220-RD53 -01 2,43
R3G 220-RC05 -03 1,20 K3G 220-RC05 -03 2,10
R3G 220-RG19 -01 1,40 K3G 220-RG19 -01 2,00
kg kg
Guard grille
p. 160
Electr. connection
p. 163 ff.
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
Curves:
Speed-controlled = max.
3η
Ped
W
I
A
LWA
dB(A)
2765
2700
2580
2635
3085
2935
2790
2940
3540
3370
3230
3310
79
85
85
85
115
115
115
115
168
168
168
168
0,67
0,69
0,70
0,70
1,10
1,10
1,10
1,10
1,40
1,40
1,40
1,40
71
67
65
66
74
69
66
70
77
73
70
72
Inlet nozzle
p. 158
Drawings
p. 22 ff.
R3G 220-RD53 -03 1,53 K3G 220-RD53 -03 2,43
D
1
2
3
4
E
E
E
E
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
22
R3G 220-RC05-01 (Centrifugal fan)
K3G 220-RC05-01 (Centrifugal module with support basket)
2
Ø72
2
Ø80
Ø27
Ø220
Ø161±0.2
71±1
63.7
Ø89
Ø5.5 (6x)
Ø155
Ø242
Ø252
0.8
21
450+20
85±10
6
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270 92
7
45°
o
247.5±0.5
Ø305±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 09609-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 220, 2 speed stages, 85 W - electronics
23
R3G 220-RD53-01 (Centrifugal fan)
K3G 220-RD53-01 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø220
Ø161±0.2
90±1
63.7
Ø101
Ø5.5 (6x)
Ø155
Ø242
Ø252
0.8
21
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270
45°
o
247.5±0.5
Ø305±0.5
92
7
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 09609-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 220, 2 speed stages, 170 W - electronics
24
R3G 220-RC05-03 (Centrifugal fan)
K3G 220-RC05-03 (Centrifugal module with support basket)
85±10
450+20
6
2
Ø72
2
Ø80
Ø27
Ø220
Ø161±0.2
71±1
63.7
Ø89
Ø5.5 (6x)
Ø155
Ø242
Ø252
0.8
21
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270 92
7
45°
o
247.5±0.5
Ø305±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
3 x brass lead tips crimped
Accessory part:
Inlet nozzle 09609-2-4013
not included in the standard
scope of delivery
Control line AWG 22,
4 x brass lead tips crimped
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 220, speed-controlled, 85 W - electronics
25
R3G 220-RG19-01 (Centrifugal fan)
K3G 220-RG19-01 (Centrifugal module with support basket)
21
0.8
R21.8
Ø252
Ø242
Ø155
63.7
Ø161
Ø220
6
85
450
Ø105
M4 (4x)
Ø58
M4 (4x)
Ø115
max.Ø95
2
Ø5.5 (6x)
71
95
±10
±0.2
±0.2
±1
±1
+20
Depth of screw max. 6 mm
Accessory part:
Inlet nozzle 09609-2-4013
not included in the standard
scope of delivery Depth of screw max. 6 mm
Ø
305
Ø294.5
247.5
45°
±0.5
±0.5
±0.5
270
Ø5 (4x) 7
99
116
Ø305
±0.5
450
85
6
±10
+20
Mounting
dimensions:
Connection line PVC 4X 0.25 mm2,
4 x brass lead tips crimped
Connection line PVC 3G 0.5 mm2,
3 x brass lead tips crimped
EC centrifugal fans – RadiCal
backward curved, Ø 220, speed-controlled, 115 W - electronics
26
R3G 220-RD53-03 (Centrifugal fan)
K3G 220-RD53-03 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø220
Ø161±0.2
90±1
63.7
Ø101
Ø5.5 (6x)
Ø155
Ø242
Ø252
0.8
21
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270 92
7
45°
o
247.5±0.5
Ø305±0.5
Connection line AWG 20,
3 x brass lead tips crimped
Control line AWG 22,
4 x brass lead tips crimped
Depth of screw max. 5 mm
Accessory part:
Inlet nozzle 09609-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 220, speed-controlled, 170 W - electronics
27
28
*3G 225 M3G 055-CF 1~ 200-240 50/60 2200 82 0,70 -25..+60
*3G 225 M3G 055-DF 1~ 200-240 50/60 2860 170 1,40 -25..+60
*3G 225 M3G 055-CF 1~ 200-240 50/60 2200 82 0,70 -25..+60
*3G 225 M3G 055-CF 1~ 200-240 50/60 2440 115 1,10 -25..+40
200 400 600 800 1000 1200
0 400100 200 300 700500 600
80
160
320
400
480
560
640
720
0,4 0,8 1,2 1,6 2,0 2,4 2,8
1
1 55
3
3
7
72
6
6
2
240
4
8
8
4
cfm
qV
pfs Pa
in H2O
m3/h
2290
2170
2200
2225
1640
1585
1590
1630
3030
2910
2860
2970
2550
2495
2490
2525
70
77
82
73
27
31
31
28
150
165
170
155
91
104
105
97
0,62
0,66
0,70
0,63
0,28
0,31
0,32
0,29
1,25
1,40
1,40
1,35
0,83
0,94
0,93
0,89
69
65
60
66
61
58
53
58
78
74
68
73
74
70
65
69
A
B
B
C
D
A
Curves:
2 Speed stages
Ped
W
I
A
A
LWA
dB(A)
A
A
A
= max.
7η
1
2
3
4
5
6
7
8
A
A
A
A
1
2
3
4
5
6
7
8
B
B
B
B
B
B
B
B
3
p. 164 / H3)
p. 164 / H3)
p. 165 / H4)
p. 163 / H5)
*3G 225 M3G 055-DF 1~ 200-240 50/60 2860 170 1,40 -25..+60
Ep. 165 / H4)
EC centrifugal fans – RadiCal
backward curved, Ø 225
Material: Housing: PA plastic 6, fibreglass-reinforced
Impeller: PA plastic 6, fibreglass-reinforced
Rotor: Thick layer passivated
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B"
Mounting position: Any
Condensate discharges: None, open rotor
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
29
R3G 225-RD05 -01 1,40 K3G 225-RD05 -01 2,00
R3G 225-RE07 -01 1,60 K3G 225-RE07 -01 2,20
R3G 225-RD05 -03 1,40 K3G 225-RD05 -03 2,00
R3G 225-RH19 -01 1,50 K3G 225-RH19 -01 2,10
200 400 600 800 1000 1200
0 400100 200 300 700500 600
80
160
320
400
480
560
640
720
0,4 0,8 1,2 1,6 2,0 2,4 2,8
1
1 1
3
3
3
2
2
2
240
4
4
4
cfm
qV
pfs Pa
in H2O
m3/h
2290
2170
2200
2225
2685
2445
2440
2640
3030
2910
2860
2970
70
77
82
73
115
115
115
115
150
165
170
155
0,62
0,66
0,70
0,63
1,10
1,10
1,10
1,10
1,25
1,40
1,40
1,35
69
65
60
66
73
67
63
71
78
74
68
73
C
E
kg kg
Guard grille
p. 160
Electr. connection
p. 163 ff.
Curves:
Speed-controlled
1
2
3
4
C
C
C
C
= max.
3η
Ped
W
I
A
LWA
dB(A)
Inlet nozzle
p. 158
Drawings
p. 30 ff.
R3G 225-RE07 -03 1,60 K3G 225-RE07 -03 2,20
D
1
2
3
4
E
E
E
E
1
2
3
4
D
D
D
D
Technical features: See electrical connections p. 163 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
30
R3G 225-RD05-01 (Centrifugal fan)
K3G 225-RD05-01 (Centrifugal module with support basket)
2
Ø72
2
Ø80
Ø27
Ø225
Ø153.5±0.2
99±1
88.4
Ø89
Ø4.5 (4x)
Ø146
Ø210
Ø223
1.5
28
450+20
85±10
6
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270 112
7
45°
o
247.5±0.5
Ø305±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96358-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 225, 2 speed stages, 85 W - electronics
31
R3G 225-RE07-01 (Centrifugal fan)
K3G 225-RE07-01 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø225
Ø153.5±0.2
99±1
88.4
Ø101
Ø4.5 (4x)
Ø146
Ø210
Ø223
1.5
28
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270
45°
o
247.5±0.5
Ø305±0.5
119
7
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96358-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 225, 2 speed stages, 170 W - electronics
32
R3G 225-RD05-03 (Centrifugal fan)
K3G 225-RD05-03 (Centrifugal module with support basket)
85±10
450+20
6
2
Ø72
2
Ø80
Ø27
Ø225
Ø153.5±0.2
99±1
88.4
Ø89
Ø4.5 (4x)
Ø146
Ø210
Ø223
1.5
28
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270 112
7
45°
o
247.5±0.5
Ø305±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
3 x brass lead tips crimped
Accessory part:
Inlet nozzle 96358-2-4013
not included in the standard
scope of delivery
Control line AWG 22,
4 x brass lead tips crimped
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 225, speed-controlled, 85 W - electronics
33
R3G 225-RH19-01 (Centrifugal fan)
K3G 225-RH19-01 (Centrifugal module with support basket)
88.4
94
111
Ø115
max.Ø95
Ø153.5
Ø225
Ø146
Ø210
Ø223
1.5
28
R25
Ø4.5 (4x)
Ø58
Ø105
M4 (4x)
M4 (4x)
6
85
450
±0.2
±0.2
±10
±1
±1
2
+20
Depth of screw max. 6 mm
Accessory part:
Inlet nozzle 96358-2-4013
not included in the standard
scope of delivery Depth of screw max. 6 mm
Ø
305
Ø294.5
247.5
4
±0.5
±0.5
±0.5
270
Ø5 (4x) 7
112
127.15
Ø
305
±0.5
450
85
6
±10
+20
Mounting
dimensions:
Connection line PVC 4X 0.25 mm2,
4 x brass lead tips crimped
Connection line PVC 3G 0.5 mm2,
3 x brass lead tips crimped
EC centrifugal fans – RadiCal
backward curved, Ø 225, speed-controlled, 115 W - electronics
34
R3G 225-RE07-03 (Centrifugal fan)
K3G 225-RE07-03 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø225
Ø153.5±0.2
99±1
88.4
Ø101
Ø4.5 (4x)
Ø146
Ø210
Ø223
1.5
28
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø294.5
Ø305±0.5
Ø5 (4x)
o
270 119
7
45°
o
247.5±0.5
Ø305±0.5
Connection line AWG 20,
3 x brass lead tips crimped
Control line AWG 22,
4 x brass lead tips crimped
Depth of screw max. 5 mm
Accessory part:
Inlet nozzle 96358-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 225, speed-controlled, 170 W - electronics
35
36
*3G 250 M3G 055-CF 1~ 200-240 50/60 1955 80 0,70 -25..+60
*3G 250 M3G 055-DF 1~ 200-240 50/60 2510 170 1,40 -25..+60
*3G 250 M3G 055-CF 1~ 200-240 50/60 1955 80 0,70 -25..+60
*3G 250 M3G 055-DF 1~ 200-240 50/60 2510 170 1,40 -25..+60
200 400 600 800 1000 1200 1400
0 400100 200 300 800700500 600
100
300
400
500
600
700
0,4 0,8 1,2 1,6 2,0 2,4
1
1 55
3
3
7
7
2
6
6
2
200
4
8
8
4
cfm
qV
pfs Pa
in H2O
m3/h
2050
1965
1955
1990
1325
1290
1290
1330
2680
2565
2510
2610
2330
2265
2250
2285
70
80
80
78
22
26
26
26
145
170
170
160
96
110
115
110
0,60
0,68
0,70
0,65
0,23
0,26
0,28
0,26
1,15
1,40
1,40
1,30
0,80
0,92
0,96
0,93
69
66
61
66
60
57
53
57
76
71
67
73
72
67
64
68
A
B
B
C
D
A
Curves:
2 Speed stages
Ped
W
I
A
A
LWA
dB(A)
A
A
A
= max.
7η
1
2
3
4
5
6
7
8
A
A
A
A
1
2
3
4
5
6
7
8
B
B
B
B
B
B
B
B
3
p. 164 / H3)
p. 164 / H3)
p. 165 / H4)
p. 165 / H4)
EC centrifugal fans – RadiCal
backward curved, Ø 250
Material: Housing: PA plastic 6, fibreglass-reinforced
Impeller: PA plastic 6, fibreglass-reinforced
Rotor: Thick layer passivated
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B"
Mounting position: Any
Condensate discharges: None, open rotor
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
37
R3G 250-RD17 -01 1,50 K3G 250-RD17 -01 2,28
R3G 250-RE07 -05 1,91 K3G 250-RE07 -05 2,69
R3G 250-RD17 -03 1,50 K3G 250-RD17 -03 2,28
R3G 250-RE07 -07 1,91 K3G 250-RE07 -07 2,69
200 400 600 800 1000 1200 1400
0 400100 200 300 800700500 600
100
300
400
500
600
700
0,4 0,8 1,2 1,6 2,0 2,4
1
1
3
3
2
2
200
4
4
cfm
qV
pfs Pa
in H2O
m3/h
2050
1965
1955
1990
2680
2565
2510
2610
70
80
80
78
145
170
170
160
0,60
0,68
0,70
0,65
1,15
1,40
1,40
1,30
69
66
61
66
76
71
67
73
C
D
Technical features: See electrical connections p. 164 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
kg kg
Guard grille
p. 160
Electr. connection
p. 164 ff.
Curves:
Speed-controlled
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
= max.
3η
Ped
W
I
A
LWA
dB(A)
Inlet nozzle
p. 158
Drawings
p. 38 ff.
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
38
R3G 250-RD17-01 (Centrifugal fan)
K3G 250-RD17-01 (Centrifugal module with support basket)
2
Ø72
2
Ø80
Ø27
Ø250
Ø172.5±0.2
99±1
85
Ø89
Ø4.5 (4x)
Ø164.5
Ø240
Ø255
1.5
31
450+20
85±10
6
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø322
Ø340±0.5
Ø5 (4x)
o
300 108.5
7
45°
o
276±0.5
Ø340±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96359-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 250, 2 speed stages, 85 W - electronics
39
R3G 250-RE07-05 (Centrifugal fan)
K3G 250-RE07-05 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø250
Ø172.5±0.2
99±1
85
Ø101
Ø4.5 (4x)
Ø164.5
Ø240
Ø255
1.5
31
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø322
Ø340±0.5
Ø5 (4x)
o
300
45°
o276±0.5
Ø340
±0.5
108.5
7
Depth of screw max. 5 mm
Connection line AWG 20,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96359-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 250, 2 speed stages, 170 W - electronics
40
R3G 250-RD17-03 (Centrifugal fan)
K3G 250-RD17-03 (Centrifugal module with support basket)
85±10
450+20
6
2
Ø72
2
Ø80
Ø27
Ø250
Ø172.5±0.2
99±1
85
Ø89
Ø4.5 (4x)
Ø164.5
Ø240
Ø255
1.5
31
Ø58±0.2
M4 (4x)
450+20
85±10
6
Ø322
Ø340±0.5
Ø5 (4x)
o
300 108.5
7
45°
o
276±0.5
Ø340±0.5
Depth of screw max. 5 mm
Connection line AWG 20,
3 x brass lead tips crimped
Accessory part:
Inlet nozzle 96359-2-4013
not included in the standard
scope of delivery
Control line AWG 22,
4 x brass lead tips crimped
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 250, speed-controlled, 85 W - electronics
41
R3G 250-RE07-07 (Centrifugal fan)
K3G 250-RE07-07 (Centrifugal module with support basket)
Ø90±0.2
M6(4x)
85±10
450+20
6
2
Ø72
5
Ø75
Ø250
Ø172.5±0.2
99±1
85
Ø101
Ø4.5 (4x)
Ø164.5
Ø240
Ø255
1.5
31
Ø58±0.2
M4(4x)
450+20
85±10
6
Ø322
Ø340±0.5
Ø5 (4x)
o
300
45°
o276±0.5
Ø340
±0.5
108.5
7
Connection line AWG 20,
3 x brass lead tips crimped
Control line AWG 22,
4 x brass lead tips crimped
Depth of screw max. 5 mm
Accessory part:
Inlet nozzle 96359-2-4013
not included in the standard
scope of delivery Depth of screw max. 10 mm
Mounting
dimensions:
EC centrifugal fans – RadiCal
backward curved, Ø 250, speed-controlled, 170 W - electronics
42
*3G 250 M3G 084-DF 1~ 200-277 50/60 3740 500 2,20 -25..+60 p. 166 / P5)
*3G 250 M3G 084-DF 1~ 200-277 50/60 4250 750 3,30 -25..+60 p. 166 / P5)
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PA
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
–Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
A
B
400 800 1200 1600 2000
0
400
800
1,6
200
0,8 3,2
1000
4,0
600
2,4
200 400 600 800 1000 1200 cfm
qV
pfs Pa
in H2O
m3/h
3
3
4
4
11
2
2
1200
4,8
1400
5,6
4100
3870
3740
3860
4250
4250
4250
4250
500
500
500
500
585
685
750
695
2,20
2,20
2,20
2,20
2,60
3,00
3,30
3,10
89
83
78
84
90
86
82
84
A
B
Curves: Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
EC centrifugal fans – RadiCal
backward curved, Ø 250
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
43
R3G 250-RR01 -H1 4,1 K3G 250-RR01 -H2 8,1
R3G 250-RR02 -I1 4,4 K3G 250-RR02 -I2 8,5
Technical features: See electrical connections p. 166
EMC:Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards:EN 60335-1, CE
Approvals:VDE, UL, CSA, CCC, GOST are applied for
Guard grille
p. 160
Electr. connection
p. 166
kg kg
Inlet nozzle
p. 158 ff.
Drawings
p. 44 ff.
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
44
EC centrifugal fans – RadiCal
backward curved, Ø 250
R3G 250-RR01-H1 (Centrifugal fan)
K3G 250-RR01-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
85
106.5
±1.8
Ø172 +0.3
-0.5
Ø250
Ø164.5
4x Ø4.5
1.5
Ø240
Ø255
2
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85
±10
+20
0
8
31
R28
400
Ø11 (4x)
350
295
130.5
178
Ø250
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
Observe the correct mounting position!
Install the support struts only as shown in the view!
45
EC centrifugal fans – RadiCal
backward curved, Ø 250
R3G 250-RR02-I1 (Centrifugal fan)
K3G 250-RR02-I2 (Centrifugal module with support bracket)
M6 (4x)
64.1
85
106.5
±1.8
Ø172 +0.3
-0.5
Ø250
Ø164.5
4x Ø4.5
1.5
Ø240
Ø255
2
Ø186 ±0.5
Ø169 ±0.35
Ø200
600
85
±10
+20
0
8
31
R28
400
Ø11 (4x)
350
295
130.5
194.6
Ø250
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
Observe the correct mounting position!
Install the support struts only as shown in the view!
46
*3G 280 M3G 074-CF 1~ 200-240 50/60 1910 168 1,40 -25..+60 p. 165 / H4)
*3G 280 M3G 084-DF 1~ 200-277 50/60 2700 500 2,20 -25..+60 p. 166 / P5)
*3G 280 M3G 084-DF 1~ 200-277 50/60 2900 660 2,90 -25..+60 p. 166 / P5)
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PP
Rotor: Surface passivated, Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B", "F"
Mounting position: any, Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: None (open rotor), Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
A B C
A B C
A B C
B CA
A
B
C
500 1000 1500 2000 2500 3000
0
200
400
0,8
100
0,4 1,6
500
2,0
300
1,2
200 400 600 800 1000 1200 1400 1600 1800 cfm
qV
pfs Pa
in H2O
m3/h
3
3
3
4
4
4
111
2
2
2
600
2,4
700
2,8
800
3,2
900
3,6
1980
1910
1775
1840
2880
2800
2700
2810
150
168
165
165
460
500
500
500
1,05
1,40
1,30
1,30
2,00
2,20
2,20
2,20
75
69
64
64
85
80
74
78
A
C
Curves: Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
2η
B
2900
2900
2900
2900
490
600
660
600
2,20
2,70
2,90
2,70
86
81
76
79
1
2
3
4
C
C
C
C
= max.
3η
A
C
B
EC centrifugal fans – RadiCal
backward curved, Ø 280
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
47
R3G 280-RB02 -03 2,7 K3G 280-RB02 -03 6,8
R3G 280-RR03 -H1 4,3 K3G 280-RR03 -H2 8,4
R3G 280-RR04 -I1 4,6 K3G 280-RR04 -I2 8,8
Technical features: See electrical connections p. 165 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE; EN 60335-1, EN 61800-5-1, CE
Approvals: VDE, CURUS on request; VDE, UL, CSA, CCC, GOST are applied for
B C
A
A
A B C
Guard grille
p. 160
Electr. connection
p. 165 ff.
Centrifugal fan kg
Mass of
centrifugal fan
kg
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Inlet nozzle
p. 158 ff.
Drawings
p. 48 ff.
48
EC centrifugal fans – RadiCal
backward curved, Ø 280
R3G 280-RB02-03 (Centrifugal fan)
K3G 280-RB02-03 (Centrifugal module with support bracket)
127
140
Ø187.5
Ø294
6
85
+20
600
Ø90
Ø125
M4(4x)
M6(4x)
150
5
8
Ø75
Ø132.5
Ø101
±10
±0.2
±1
Ø176.7
4x Ø4.5
1.25
Ø260
Ø280
46
Ø179.6
R17
R53
R33
400
350
Ø
11
(4x)
298
2
193.5
177.5
Ø
294
+20
600
6
85
±3
±2.5
Depth of screw max. 10 mm
Connection line AWG 20,
3 x crimped core-end sleeves
Accessory part:
Inlet nozzle 28000-2-4013
not included in the standard
scope of delivery
Connection line AWG 22,
4 x crimped core-end sleeves
Observe the correct mounting position!
Install the support struts only as shown in the view!
49
EC centrifugal fans – RadiCal
backward curved, Ø 280
R3G 280-RR03-H1 (Centrifugal fan)
K3G 280-RR03-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
127
142.75
±1.8
Ø187.5 ±0.3
Ø294
Ø176.7
4x Ø4.5
1.25
Ø260
Ø280
8
Ø164 ±0.5
Ø150 ±0.35
Ø178
600
85
±10
+20
0
8
46
Ø179.6
R17
R53
R33
400
Ø11 (4x)
350
295
175.5
223.2
Ø294
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
Observe the correct mounting position!
Install the support struts only as shown in the view!
50
R3G 280-RR04-I1 (Centrifugal fan)
K3G 280-RR04-I2 (Centrifugal module with support bracket)
M6 (4x)
64.1
127
142.75
±1.8
Ø187.5 ±0.3
Ø294
Ø176.7
4x Ø4.5
1.25
Ø260
Ø280
8
Ø186 ±0.5
Ø169 ±0.35
Ø200
600
85
±10
+20
0
8
46
Ø179.6
R17
R53
R33
400
Ø11 (4x)
350
295
239.6
Ø294
±3
175.5
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 280
Observe the correct mounting position!
Install the support struts only as shown in the view!
51
52
*3G 310 M3G 074-CF 1~ 200-240 50/60 1525 150 1,20 -25..+60 p. 165 / H4)
*3G 310 M3G 084-DF 1~ 200-277 50/60 2360 500 2,20 -25..+60 p. 166 / P5)
*3G 310 M3G 084-FA 1~ 200-277 50/60 2640 740 3,25 -25..+60 p. 166 / P5)
*3G 310 M3G 084-FA 3~ 380-480 50/60 2700 790 1,25 -25..+60 p. 167 / P6)
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PP
Rotor: Surface passivated, Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B", "F"
Mounting position: any, Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: None (open rotor), Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
B C
B C
D
D
A B C
B C DA
D
A
A
A
B
C
D
500 1000 1500 2000 2500 3000 3500 4000
0
200
400
0,8
100
0,4 1,6
500
2,0
300
1,2
500 1000 1500 2000 cfm
qV
pfs Pa
in H2O
m3/h
3
33
3
4
4
4
111
2
2
2
600
2,4
700
2,8
800
3,2
900
3,6
1000
4,0
1600
1545
1525
1545
2510
2440
2360
2410
115
140
150
140
430
500
500
500
0,95
1,10
1,20
1,15
1,90
2,20
2,20
2,20
69
65
59
62
81
76
72
77
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
2700
2700
2640
2700
2700
2700
2700
2700
550
730
740
730
560
720
790
725
2,45
3,20
3,25
3,20
0,89
1,15
1,25
1,15
84
79
75
79
84
79
76
80
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
D
EC centrifugal fans – RadiCal
backward curved, Ø 310
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
53
R3G 310-RB01 -03 2,9 K3G 310-RB01 -03 7,5
R3G 310-RR05 -H1 4,7 K3G 310-RR05 -H2 9,6
R3G 310-RS01 -I1 5,7 K3G 310-RS01 -I2 10,7
R3G 310-RS05 -J1 5,5 K3G 310-RS05 -J2 10,5
Technical features: See electrical connections p. 165 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE; EN 60335-1, EN 61800-5-1, CE
Approvals: VDE, CURUS on request; VDE, UL, CSA, CCC, GOST are applied for
B C DA
A B C D
A
Guard grille
p. 160
Electr. connection
p. 165 ff.
kg kg
Inlet nozzle
p. 158 ff.
Drawings
p. 54 ff.
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
54
R3G 310-RB01-03 (Centrifugal fan)
K3G 310-RB01-03 (Centrifugal module with support bracket)
6
85
+20
600
Ø90
Ø125
M4(4x)
M6(4x)
8
Ø204
Ø325.5
141.5
153
163.4
5
Ø132.5
Ø101
Ø75
Ø280
Ø300
Ø191.4
Ø193.4
1.5
58.5
Ø4.54x
R24.3
R71.1
R45.4
±10
±0.2
±1
440
Ø6.4 (8x)
420
320
200
216
Ø325.5
±3
±2.5
2
Depth of screw max. 10 mm
Connection line AWG 20,
3 x crimped core-end sleeves
Accessory part:
Inlet nozzle 31000-2-4013
not included in the standard
scope of delivery
Connection line AWG 22,
4 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 310
Observe the correct mounting position!
Install the support struts only as shown in the view!
55
R3G 310-RR05-H1 (Centrifugal fan)
K3G 310-RR05-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
141.5
153
±2
Ø204 ±0.4
Ø325.5
Ø191.5
4x Ø4.5
1.5
Ø280
Ø300
8
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85 ±10
+20
0
8
58.5
Ø193.4
R24
R71
R45
440
Ø6.4 (8x)
420
320
200
247.7
Ø325.5
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 310
Observe the correct mounting position!
Install the support struts only as shown in the view!
56
R3G 310-RS01-I1 (Centrifugal fan)
K3G 310-RS01-I2 (Centrifugal module with support bracket)
M6 (4x)
64.1
141.5
168
±2
Ø204 ±0.4
Ø325.5
Ø191.5
4x Ø4.5
1.5
Ø280
Ø300
8
Ø186 ±0.35
Ø169 ±0.35
Ø200
600
85 ±10
+20
0
8
58.5
Ø193.4
R24
R71
R45
440
Ø6.4 (8x)
420
320
215
279
Ø325.5
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 310
Observe the correct mounting position!
Install the support struts only as shown in the view!
57
R3G 310-RS05-J1 (Centrifugal fan)
K3G 310-RS05-J2 (Centrifugal module with support bracket)
M6 (4x)
64.1
141.5
168
±2
Ø204 ±0.4
Ø325.5
Ø191.5
4x Ø4.5
1.5
Ø280
Ø300
8
Ø186 ±0.35
Ø169 ±0.35
Ø200
600
85 ±10
+20
0
8
58.5
Ø193.4
R24
R71
R45
440
Ø6.4 (8x)
420
320
215
279
Ø325.5
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
6 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 310
Observe the correct mounting position!
Install the support struts only as shown in the view!
58
*3G 355 M3G 074-CF 1~ 200-240 50/60 1250 168 1,40 -25..+60 p. 165 / H4)
*3G 355 M3G 084-DF 1~ 200-277 50/60 1450 250 1,10 -25..+60 p. 166 / P5)
*3G 355 M3G 084-FA 1~ 200-277 50/60 1850 500 2,20 -25..+60 p. 166 / P5)
*3G 355 M3G 084-GF 1~ 200-277 50/60 2100 750 3,30 -25..+60 p. 166 / P5)
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PP
Rotor: Surface passivated, Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "B", "F"
Mounting position: any, Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: None (open rotor), Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
B
B C D
C D
A B C D E
E
B C D EA
EA
A
*3G 355 M3G 112-EA 3~ 380-480 50/60 2400 1140 1,80 -25..+60 p. 167 / P6)
A
B
C
D
E
1000 2000 3000 4000 5000
0
200
400
0,8
100
0,4 1,6
500
2,0
300
1,2
500 1000 1500 2000 2500 3000 cfm
qV
pfs Pa
in H2O
m3/h
3
3
3
3
3
4
4
4
4
4
11 1 11
2
2
2
2
2
600
2,4
700
2,8
800
3,2
900
3,6
1000
4,0
1425
1305
1250
1280
1660
1505
1450
1525
165
165
168
165
250
250
250
250
1,35
1,35
1,40
1,35
1,10
1,10
1,10
1,10
71
65
58
60
77
68
63
68
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
2050
1940
1850
1890
2240
2165
2100
2165
455
500
500
500
630
750
750
740
2,00
2,20
2,20
2,20
2,75
3,30
3,30
3,25
87
78
70
73
87
81
74
77
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
D
E
2400
2400
2400
2400
790
1040
1140
1090
1,25
1,65
1,80
1,70
91
83
76
79
1
2
3
4
E
E
E
E
EC centrifugal fans – RadiCal
backward curved, Ø 355
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
59
R3G 355-RB03 -03 3,7 K3G 355-RB03 -03 9,7
R3G 355-RR06 -G1 5,0 K3G 355-RR06 -G2 10,8
R3G 355-RS02 -H1 5,7 K3G 355-RS02 -H2 11,6
R3G 355-RT01 -I1 6,9 K3G 355-RT01 -I2 14,9
Technical features: See electrical connections p. 165 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE; EN 60335-1, EN 61800-5-1, CE
Approvals: VDE, CURUS on request; VDE, UL, CSA, CCC, GOST are applied for
B C D
A
A E
B C D E
A
R3G 355-RJ75 -01 8,3 K3G 355-RJ75 -01 16,3
kg kg
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Guard grille
p. 160
Electr. connection
p. 165 ff.
Inlet nozzle
p. 158 ff.
Drawings
p. 60 ff.
60
R3G 355-RB03-03 (Centrifugal fan)
K3G 355-RB03-03 (Centrifugal module with support bracket)
6
85
+20
600
M4(4x)
M6(4x)
Ø125
Ø90
Ø132.5
Ø101
Ø75
5
181.4
161.5
171
Ø237
Ø372.5
Ø325
Ø350
Ø4.54x
1.5
60
Ø227
R69.5
R22.5
R43.5
Ø223
10
±0.2
±10
±1
496
Ø6.4 (8x)
476
351
226
242
Ø372.5
±3
±2
2
Depth of screw max. 10 mm
Connection line AWG 20,
3 x crimped core-end sleeves
Accessory part:
Inlet nozzle 35500-2-4013
not included in the standard
scope of delivery
Connection line AWG 22,
4 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 355
Observe the correct mounting position!
Install the support struts only as shown in the view!
61
R3G 355-RR06-G1 (Centrifugal fan)
K3G 355-RR06-G2 (Centrifugal module with support bracket)
M6 (4x)
47.7
161.75
170
±2
Ø237 +1.5
-0.4
Ø372.5
Ø223
4x Ø4.5
1.5
Ø325
Ø350
10
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85 ±10
+20
0
8
60
Ø227
R22.5
R69.5
R43.5
496
Ø6.4 (8x)
476
351.5
217
265
Ø372.5
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 355
Observe the correct mounting position!
Install the support struts only as shown in the view!
62
R3G 355-RS02-H1 (Centrifugal fan)
K3G 355-RS02-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
161.75
183
±2
Ø237 +1.5
-0.4
Ø372.5
Ø223
4x Ø4.5
1.5
Ø325
Ø350
10
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85 ±10
+20
0
8
60
Ø227
R22.5
R69.5
R43.5
496
Ø6.4 (8x)
476
351.5
229
277
Ø372.5
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 355
Observe the correct mounting position!
Install the support struts only as shown in the view!
63
R3G 355-RT01-I1 (Centrifugal fan)
K3G 355-RT01-I2 (Centrifugal module with support bracket)
M6 (4x)
64.1
161.75
191
±2
Ø237
Ø372.5
Ø223
4x Ø4.5
1.5
Ø325
Ø350
10
Ø186 ±0.5
Ø169 ±0.35
Ø200
600
85
±10
+20
0
8
60
Ø227
R22.5
R69.5
R43.5
-0.4
+1.5
500
Ø11 (4x)
450
372
237
301
Ø372.5
±3
±2
15
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 355
Observe the correct mounting position!
Install the support struts only as shown in the view!
64
R3G 355-RJ75-01 (Centrifugal fan)
K3G 355-RJ75-01 (Centrifugal module with support bracket)
Ø 186
M6 (4x)
45°
4x90°
Ø 325
Ø 350
Ø 4.54x
1.5
60
Ø 223
Ø 227
Ø 237
Ø 372.5
Ø169
Ø 200
R22.5
R69.5
R43.5
162
191
56.5
850
85
8
±0.5
+20
±10
+1.5
±2
-0.4
10
372
450
500
15
237.5
294
Ø 11 (4x)
Ø 372.5
±2.5
±3
Depth of screw 8-10 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery
Connection line PVC AWG 18,
6 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 355
Observe the correct mounting position!
Install the support struts only as shown in the view!
65
66
*3G 400 M3G 084-DF 1~ 200-277 50/60 1170 250 1,10 -25..+60 p. 166 / P5)
*3G 400 M3G 084-FA 1~ 200-277 50/60 1500 500 2,20 -25..+50 p. 166 / P5)
*3G 400 M3G 084-GF 1~ 200-277 50/60 1700 750 3,30 -25..+55 p. 166 / P5)
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PP
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
*3G 400 M3G 112-EA 3~ 380-480 50/60 2060 1320 2,10 -25..+50 p. 167 / P6)
A
B
C
D
1000 2000 3000 4000 5000 6000
0
200
400
0,8
100
0,4 1,6
500
2,0
300
1,2
500 1000 1500 2000 2500 3000 3500 cfm
qV
pfs Pa
in H2O
m3/h
3
3
3
3
4
4
4
4
11 1 1
2
2
2
2
600
2,4
700
2,8
800
3,2
900
3,6
1000
4,0
1320
1200
1170
1210
1725
1550
1500
1550
240
250
250
250
500
500
500
500
1,05
1,10
1,10
1,10
2,20
2,20
2,20
2,20
75
71
61
67
80
73
68
72
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
1925
1755
1700
1745
2120
2110
2060
2110
740
750
750
750
965
1240
1320
1270
3,25
3,30
3,30
3,30
1,55
2,00
2,10
2,05
83
78
72
72
89
82
74
79
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
D
EC centrifugal fans – RadiCal
backward curved, Ø 400
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
67
R3G 400-RR07 -G1 5,6 K3G 400-RR07 -G2 12,5
R3G 400-RS03 -H1 6,4 K3G 400-RS03 -H2 13,3
R3G 400-RT02 -I1 7,3 K3G 400-RT02 -I2 15,3
Technical features: See electrical connections p. 166 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, EN 61800-5-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
R3G 400-RJ75 -01 8,5 K3G 400-RJ75 -01 16,5
kg kg
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Guard grille
p. 160
Electr. connection
p. 166 ff.
Inlet nozzle
p. 158 ff.
Drawings
p. 68 ff.
68
R3G 400-RR07-G1 (Centrifugal fan)
K3G 400-RR07-G2 (Centrifugal module with support bracket)
M6 (4x)
47.7
182
194
±2
Ø266 ±0.5
Ø420
Ø257
4x Ø4.5
1.5
Ø345
Ø370
10
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85
±10
+20
0
8
66
R22
R50
R90
560
Ø6.4 (8x)
520
382
246.5
294
Ø420
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 400
Observe the correct mounting position!
Install the support struts only as shown in the view!
69
R3G 400-RS03-H1 (Centrifugal fan)
K3G 400-RS03-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
182
194
±2
Ø266 ±0.5
Ø420
Ø257
4x Ø4.5
1.5
Ø345
Ø370
10
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85
±10
+20
0
8
66
R22
R50
R90
560
Ø6.4 (8x)
520
382
246.5
294
Ø420
±3
±2
2
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 400
Observe the correct mounting position!
Install the support struts only as shown in the view!
70
R3G 400-RT02-I1 (Centrifugal fan)
K3G 400-RT02-I2 (Centrifugal module with support bracket)
M6 (4x)
64.1
182
192
±2
Ø266 ±0.5
Ø420
Ø257
4x Ø4.5
1.5
Ø345
Ø370
10
Ø186 ±0.5
Ø169 ±0.35
Ø200
600 85
±10
+20
0
8
66
R22
R50
R90
500
Ø11 (4x)
450
372
244
308
Ø420
±3
±2
15
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 400
Observe the correct mounting position!
Install the support struts only as shown in the view!
71
R3G 400-RJ75-01 (Centrifugal fan)
K3G 400-RJ75-01 (Centrifugal module with support bracket)
Ø 186
M6 (4x)
45°
4x90°
Ø 345
Ø 370
Ø 4.54x
1.5
66
Ø 257
Ø 266
Ø 420
Ø169
Ø 200
R22
R90
182
192
56.5
850
85
8
±0.5
+20
±10
±0.5
±2
10
R50
372
450
500
15
246
302.5
Ø 11 (4x)
Ø 420
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery
Connection line PVC AWG 18,
6 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 400
Observe the correct mounting position!
Install the support struts only as shown in the view!
72
*3G 450 M3G 084-FA 1~ 200-277 50/60 1000 250 1,10 -25..+60 p. 166 / P5)
*3G 450 M3G 084-GF 1~ 200-277 50/60 1260 500 2,20 -25..+50 p. 166 / P5)
*3G 450 M3G 112-EA 1~ 200-277 50/60 1440 750 3,30 -25..+60 p. 166 / P5)
*3G 450 M3G 112-GA 3~ 380-480 50/60 1550 950 1,50 -25..+60 p. 167 / P6)
A
B
C
D
1000 2000 3000 4000 5000 6000
0
200
400
0,8
100
0,4 1,6
500
2,0
300
1,2
500 1000 1500 2000 2500 3000 3500 cfm
qV
pfs Pa
in H2O
m3/h
3
3
3
3
4
4
4
4
1 1 1
2
2
2
2
600
2,4
1130
1050
1000
1031
1470
1345
1260
1295
230
250
250
250
500
500
500
500
1,05
1,10
1,10
1,10
2,00
2,20
2,20
2,20
76
68
62
70
95
80
69
71
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
1550
1525
1440
1495
1550
1550
1550
1550
570
750
750
750
600
820
950
880
2,55
3,30
3,30
3,30
1,00
1,35
1,50
1,40
79
78
72
76
79
78
74
75
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
D
EC centrifugal fans – RadiCal
backward curved, Ø 450
Material: Support bracket: Steel, coated in black
Support plate: Sheet steel, galvanised / Inlet nozzle: Plastic ABS
Impeller: Plastic PP
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
73
R3G 450-RS04 -G1 6,7
R3G 450-RT03 -H1 7,5 K3G 450-RT03 -H2
R3G 450-RJ74 -21 9,2 K3G 450-RJ74 -21
Technical features: See electrical connections p. 166 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, EN 61800-5-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
K3G 450-RS04 -G2 16,5
17,3
19,3
R3G 450-RK56 -01 10,6 K3G 450-RK56 -01 20,7
kg kg
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Guard grille
p. 160
Electr. connection
p. 166 ff.
Inlet nozzle
p. 158 ff.
Drawings
p. 74 ff.
74
R3G 450-RS04-G1 (Centrifugal fan)
K3G 450-RS04-G2 (Centrifugal module with support bracket)
M6 (4x)
47.7
218
226
±2
Ø300 ±0.5
Ø485
Ø286.7
6x Ø9
3
Ø425
Ø450
10
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85
±10
+20
0
8
50
Ø292
R20
R50
R40
630
Ø11 (8x)
580
549
260.5
308
Ø485
±3
±2
15
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 450
Observe the correct mounting position!
Install the support struts only as shown in the view!
75
R3G 450-RT03-H1 (Centrifugal fan)
K3G 450-RT03-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
218
226
±2
Ø300 ±0.5
Ø485
Ø286.7
6x Ø9
3
Ø425
Ø450
10
Ø164 ±0.35
Ø150 ±0.35
Ø178
600
85
±10
+20
0
8
50
Ø292
R20
R50
R40
630
Ø11 (8x)
580
549
260.5
308
Ø485
±3
±2
15
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 450
Observe the correct mounting position!
Install the support struts only as shown in the view!
76
R3G 450-RJ74-21 (Centrifugal fan)
K3G 450-RJ74-21 (Centrifugal module with support bracket)
Ø 300
Ø 485
Ø 425
Ø 450
Ø 286.7
Ø292
Ø 96x
3
50
R40
R50
R20
233.5
218
56.5
Ø169
Ø 200
M6 (4x)
45°
4x90°
Ø 186
850
85
8
±0.5
+20
±10
±0.5
±2
10
549
580
630
Ø 11 (8x)
15
268
324.5
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery
Connection line PVC AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 450
Observe the correct mounting position!
Install the support struts only as shown in the view!
77
R3G 450-RK56-01 (Centrifugal fan)
K3G 450-RK56-01 (Centrifugal module with support bracket)
Ø 300
Ø 485
Ø 425
Ø 450
Ø 286.7
Ø292
Ø 96x
3
50
R40
R50
R20
233.5
218
56.5
Ø169
Ø 200
M6 (4x)
45°
4x90°
Ø 186
850
85
8
±0.5
+20
±10
±0.5
±2
10
549
580
630
Ø 11 (8x)
15
268
324.5
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery
Connection line PVC AWG 18,
6 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 450
Observe the correct mounting position!
Install the support struts only as shown in the view!
78
*3G 500 M3G 084-FA 1~ 200-277 50/60 750 250 1,10 -25..+60 p. 166 / P5)
*3G 500 M3G 084-GF 1~ 200-277 50/60 900 460 2,00 -25..+40 p. 166 / P5)
*3G 500 M3G 112-GA 1~ 200-277 50/60 1100 750 3,30 -25..+60 p. 166 / P5)
*3G 500 M3G 112-IA 3~ 380-480 50/60 1350 1320 2,10 -25..+50 p. 167 / P6)
*3G 500 M3G 150-FF 3~ 380-480 50/60 1700 2600 4,00 -25..+60 p. 169 / M5)
A
B
C
D
E
2000 4000 6000 8000 10000
0
200
600
0,8
100
0,4
400
1,6
300
1,2 2,4
700
2,8
800
3,2
900
3,6
500
2,0
1000 2000 3000 4000 5000 6000 cfm
qV
pfs Pa
in H2O
m3/h
3
3
3
3
4
4
4
43
4
1 1 1 1 1
2
2
2
2
2
1000
4,0
1100
4,4
825
765
750
795
900
900
900
900
230
250
250
250
300
410
460
400
1,00
1,10
1,10
1,10
1,30
1,80
2,00
1,75
68
62
56
59
70
66
62
61
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
1250
1155
1100
1150
1495
1410
1350
1420
750
750
750
750
1215
1320
1320
1320
3,30
3,30
3,30
3,30
1,90
2,10
2,10
2,10
77
73
67
69
82
77
71
76
1
2
3
4
C
C
C
C
1
2
3
4
D
D
D
D
D
E
1695
1695
1700
1695
1790
2300
2600
2230
2,80
3,60
4,00
3,50
86
82
77
81
1
2
3
4
E
E
E
E
EC centrifugal fans – RadiCal
backward curved, Ø 500
Material: Support bracket: Steel, coated in black
Support plate: Sheet steel, galvanised / Inlet nozzle: Plastic ABS
Impeller: Plastic PP
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
79
R3G 500-RS06 -G1 8,6 K3G 500-RS06 -G2 18,9
R3G 500-RT04 -H1 9,5 K3G 500-RT04 -H2 19,7
R3G 500-RK55 -21 12,6 K3G 500-RK55 -21 23,1
R3G 500-RL96 -01 14,1 K3G 500-RL96 -01 24,6
R3G 500-RA24 -71 21,0 K3G 500-RA24 -71 35,0
Technical features: See electrical connections p. 166 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Terminal box design: Electrical connection via terminal strip
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, EN 61800-5-1, CE; EN 61800-5-1, CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
A B C D E
A B C D
E
kg kg
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Guard grille
p. 160
Electr. connection
p. 166 ff.
Inlet nozzle
p. 158 ff.
Drawings
p. 80 ff.
80
R3G 500-RS06-G1 (Centrifugal fan)
K3G 500-RS06-G2 (Centrifugal module with support bracket)
M6 (4x)
47.7
227
256.5
±3
Ø334.3
Ø525
Ø319.5
6x Ø9
3.5
Ø445
Ø470
12
Ø164 ±0.35
Ø150 ±0.35
Ø178
75
R28
R87
R49
600
85 ±10
+20
0
8
-0.5
+1.0
630
Ø11 (8x)
580
549
311.5
359
Ø525
±3
±2
15
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 500
Observe the correct mounting position!
Install the support struts only as shown in the view!
81
R3G 500-RT04-H1 (Centrifugal fan)
K3G 500-RT04-H2 (Centrifugal module with support bracket)
M6 (4x)
47.7
227
256.5
±3
Ø334.5
Ø525
Ø319.5
6x Ø9
3.5
Ø445
Ø470
12
Ø164 ±0.35
Ø150 ±0.35
Ø178
75
R28
R87
R49
600
85 ±10
+20
0
8
-0.5
+1.0
630
Ø11 (8x)
580
549
311.5
359
Ø525
±3
±2
15
Depth of screw max. 16 mm
Connection line AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery
Connection line AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 500
Observe the correct mounting position!
Install the support struts only as shown in the view!
82
R3G 500-RK55-21 (Centrifugal fan)
K3G 500-RK55-21 (Centrifugal module with support bracket)
56.5
247.5
227
Ø 334.3
Ø 200
Ø169
6x Ø9
Ø 445
Ø 470
Ø 319.5
Ø 324.5
R49
R87
R28
3.5
75 Ø 186
M6 (4x)
45°
4x90°
850
85
8
Ø 525
±0.5
+20
±10
±2
±0.5
10
549
580
630
Ø11 (8x)
15
304.5
361
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery
Connection line PVC AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 500
Observe the correct mounting position!
Install the support struts only as shown in the view!
83
R3G 500-RL96-01 (Centrifugal fan)
K3G 500-RL96-01 (Centrifugal module with support bracket)
56.5
247.5
227
Ø 334.5
Ø 200
Ø169
Ø 445
Ø 470
Ø 319.5
Ø 324.5
R49
R87
R28
3.5
75 Ø 186
M6 (4x)
45°
4x90°
850
85
8
Ø 525
±0.5
+20
±10
±2
+1
-0.5
10
6x Ø9
549
580
630
Ø11 (8x)
15
304.5
361
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery
Connection line PVC AWG 18,
6 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 500
Observe the correct mounting position!
Install the support struts only as shown in the view!
84
R3G 500-RA24-71 (Centrifugal fan)
K3G 500-RA24-71 (Centrifugal module with support bracket)
227
258
70
Ø334.5
Ø525
Ø232
3.5
75
Ø470
Ø445
Ø319.5
R49
R87
R28
M10 (6x)
6x60°
Ø252
Ø275
±0.3
-0.5
±2
-2
+1
12
6x Ø9
551
580
630
Ø 11 (8x)
15
314
384
Ø 525
±2
±3
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
EC centrifugal fans – RadiCal
backward curved, Ø 500
Observe the correct mounting position!
Install the support struts only as shown in the view!
85
86
*3G 560 M3G 150-FF 1~ 200-277 50/60 1340 1590 7,00 -25..+55 p. 168 / M4)
*3G 560 M3G 150-FF 3~ 380-480 50/60 1540 2360 3,65 -25..+60 p. 169 / M5)
*3G 560 M3G 150-IF 3~ 380-480 50/60 1650 2900 4,40 -25..+55 p. 169 / M5)
A
B
C
2000 4000 6000 8000 10000 12000
0
200
600
0,8
100
0,4
400
1,6
300
1,2 2,4
700
2,8
800
3,2
900
3,6
500
2,0
1000 2000 3000 4000 5000 6000 7000 8000 cfm
qV
pfs Pa
in H2O
m3/h
3
3
4
4
3
4
1 1 1
2
22
1340
1340
1340
1340
1540
1540
1540
1540
1120
1460
1590
1520
1840
2300
2360
2310
4,90
6,40
7,00
6,65
2,90
3,60
3,65
3,60
83
78
74
76
86
81
78
80
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
1650
1650
1650
1650
2010
2630
2900
2770
3,10
4,10
4,40
4,30
87
81
77
80
1
2
3
4
C
C
C
C
EC centrifugal fans – RadiCal
backward curved, Ø 560
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PP
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
87
R3G 560-RA25 -21 22,5 K3G 560-RA25 -21 43,2
R3G 560-RA25 -71 21,6 K3G 560-RA25 -71 42,3
Technical features: See electrical connections p. 168 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Terminal box design: Electrical connection via terminal strip
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 61800-5-1; CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
R3G 560-RB31 -71 26,0 K3G 560-RB31 -71 46,7
kg kgCentrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Inlet nozzle
p. 158 ff.
Electr. connection
p. 168 ff.
Drawings
p. 88 ff.
88
R3G 560-RA25-21 (Centrifugal fan)
70
289
253
Ø418
Ø570
Ø232
R50
Ø540
1.5
83.5
Ø275
M10 (6x)
Ø252
±0.3
±2
-2
±0.7
18
6x60°
Ø9 (6x)
Ø565
Ø407
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
K3G 560-RA25-21 (Centrifugal module with support bracket)
15346
416
Ø570
Ø11 (8x)
551
750
800
±3
±2
EC centrifugal fans – RadiCal
backward curved, Ø 560
Observe the correct mounting position!
Install the support struts only as shown in the view!
89
R3G 560-RA25-71 (Centrifugal fan)
K3G 560-RA25-71 (Centrifugal module with support bracket)
70
289
253
Ø418
Ø570
Ø232
R50
Ø540
1.5
83.5
Ø275
M10 (6x)
Ø252
±0.3
±2
-2
±0.7
18
6x60°
Ø9 (6x)
Ø565
Ø407
15346
416
Ø570
Ø11 (8x)
551
750
800
±3
±2
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
EC centrifugal fans – RadiCal
backward curved, Ø 560
Observe the correct mounting position!
Install the support struts only as shown in the view!
90
R3G 560-RB31-71 (Centrifugal fan)
K3G 560-RB31-71 (Centrifugal module with support bracket)
70
289
253
Ø418
Ø570
Ø232
R50
Ø540
1.5
83.5
Ø275
M10 (6x)
Ø252
±0.3
±2
-2
±0.7
18
6x60°
Ø9 (6x)
Ø565
Ø407
15346
416
Ø570
Ø11 (8x)
551
750
800
±3
±2
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
EC centrifugal fans – RadiCal
backward curved, Ø 560
Observe the correct mounting position!
Install the support struts only as shown in the view!
91
92
*3G 630 M3G 112-IA 1~ 200-277 50/60 740 500 2,20 -25..+40 p. 166 / P5)
A
*3G 630 M3G 112-IA 1~ 200-277 50/60 840 750 3,30 -25..+40 p. 166 / P5)
B
*3G 630 M3G 112-IA 3~ 380-480 50/60 900 950 1,50 -25..+40 p. 167 / P6)
C
*3G 630 M3G 150-FF 1~ 200-277 50/60 1030 1415 6,20 -25..+50 p. 168 / M4)
D
*3G 630 M3G 150-FF 3~ 380-480 50/60 1130 1790 2,80 -25..+60 p. 169 / M5)
E
*3G 630 M3G 150-IF 3~ 380-480 50/60 1300 2700 4,15 -25..+55 p. 169 / M5)
F
2000 4000 6000 8000 10000
0
200
0,8
100
0,4
400
1,6
300
1,2
1000 2000 3000 4000 5000 6000 cfm
qV
pfs Pa
in H2O
m3/h
3
4
111
2
2
2
3
3
4
4
825
770
740
750
930
880
840
865
460
500
500
500
690
750
750
750
2,00
2,20
2,20
2,20
3,00
3,30
3,30
3,30
76
69
65
67
80
73
70
71
A
C
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
B
1
2
3
4
C
C
C
C
900
900
900
900
600
830
950
885
1,00
1,30
1,50
1,40
78
73
69
71
EC centrifugal fans – RadiCal
backward curved, Ø 630
Material: Support bracket: Steel, coated in black
Support plate and inlet nozzle: Sheet steel, galvanised
Impeller: Plastic PP
Rotor: Coated in black
Electronics enclosure: Die-cast aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
Nominal data
Type Motor VAC Hz rpm W A °C
Curve
Technical features
and electrical
connection
Nominal
voltage range
Frequency
Speed/rpm(1)
Perm. amb. temp.
Max.
input power(1)
Max.
current draw(1)
Curves: n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
93
R3G 630-RK57 -31 15,8 K3G 630-RK57 -31 34,8
R3G 630-RL94 -21 17,6 K3G 630-RL94 -21 36,6
Technical features: See electrical connections p. 166 ff.
EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Terminal box design: Electrical connection via terminal strip
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 61800-5-1; CE
Approvals: VDE, UL, CSA, CCC, GOST are applied for
R3G 630-RL95 -01 17,4 K3G 630-RL95 -01 36,4
R3G 630-RA38 -21 25,0 K3G 630-RA38 -21 50,0
R3G 630-RA21 -71 24,0 K3G 630-RA21 -71 49,0
kg kg
R3G 630-RB32 -71 29,0 K3G 630-RB32 -71 54,0
1030
1030
1030
1030
1130
1130
1130
1130
920
1240
1415
1230
1180
1640
1790
1750
4,00
5,45
6,20
5,40
1,95
2,60
2,80
2,80
82
75
74
77
84
77
74
75
1
2
3
4
D
D
D
D
1
2
3
4
E
E
E
E
1
2
3
4
F
F
F
F
1300
1300
1300
1300
1780
2420
2700
2640
2,80
3,75
4,15
4,10
87
81
77
80
2000 4000 6000 8000 10000 12000 14000 16000
0
200
600
0,8
100
0,4
400
1,6
300
1,2 2,4
700
2,8
500
2,0
1000 2000 3000 4000 5000 6000 7000 8000 9000 cfm
qV
pfs Pa
in H2O
m3/h
3
4
3
3
4
4
111
2
2
2
= max.
3η
D
E
F
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support bracket
Centrifugal module
w. support bracket
Guard grille
p. 160
Electr. connection
p. 166 ff.
Inlet nozzle
p. 158 ff.
Drawings
p. 94 ff.
Curves: n
rpm
Ped
W
I
A
LWA
dB(A)
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
94
R3G 630-RK57-31 (Centrifugal fan)
K3G 630-RK57-31 (Centrifugal module with support bracket)
Ø 600
Ø 634
Ø 452
Ø 457
Ø 472
Ø 660
Ø150
47.7
Ø200
Ø 10.5(10x)
Ø 5.2(6x)
R63.2
R129
R32.5
2
86.5
304
290
M6 (4x)
45°
4x90°
Ø 186
850
85
8
±0.5
+20
±10
+2
-0.7
±2 18
15
367.5
415
Ø 660
750
800
Ø 11(8x)
549
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery
Connection line PVC AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 630
Observe the correct mounting position!
Install the support struts only as shown in the view!
95
R3G 630-RL94-21 (Centrifugal fan)
K3G 630-RL94-21 (Centrifugal module with support bracket)
Ø 600
Ø 634
Ø 452
Ø 457
Ø 472
Ø 660
Ø169
56.5
Ø200
Ø 10.5(10x)
Ø 5.2(6x)
R63.2
R129
R32.5
2
86.5
304
290
M6 (4x)
45°
4x90°
Ø 186
850
85
8
±0.5
+20
±10
+2
-0.7
±2 18
15
367.5
424
Ø 660
750
800
Ø 11(8x)
549
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery
Connection line PVC AWG 18,
5 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 630
Observe the correct mounting position!
Install the support struts only as shown in the view!
96
R3G 630-RL95-01 (Centrifugal fan)
K3G 630-RL95-01 (Centrifugal module with support bracket)
Ø 600
Ø 634
Ø 452
Ø 457
Ø 472
Ø 660
Ø169
56.5
Ø 200
Ø 10.5(10x)
Ø 5.2(6x)
R63.2
R129
R32.5
2
86.5
304
290
M6 (4x)
45°
4x90°
Ø 186
850
85
8
±0.5
+20
±10
+2
-0.7
±2 18
15
367.5
424
Ø 660
750
800
Ø 11(4x)
549
±2.5
±3
Depth of screw max. 16 mm
Connection line PVC AWG 22,
5 x crimped core-end sleeves
Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery
Connection line PVC AWG 18,
6 x crimped core-end sleeves
EC centrifugal fans – RadiCal
backward curved, Ø 630
Observe the correct mounting position!
Install the support struts only as shown in the view!
97
R3G 630-RA38-21 (Centrifugal fan)
K3G 630-RA38-21 (Centrifugal module with support bracket)
290
333
70
Ø660
Ø452
Ø458
Ø600
Ø634
Ø10.5 (6x)
2
86.5
R32.5
R129
R63
Ø472
6x60°
M10 (6x)
Ø252
Ø275
Ø232
±0.3
±2
-0.7
-2
+2
18
15
393
463
Ø 605
Ø 660
555
750
800
Ø 11(8x)
±3
±2
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
EC centrifugal fans – RadiCal
backward curved, Ø 630
Observe the correct mounting position!
Install the support struts only as shown in the view!
98
R3G 630-RA21-71 (Centrifugal fan)
K3G 630-RA21-71 (Centrifugal module with support bracket)
290
333
70
Ø660
Ø452
Ø458
Ø600
Ø634
Ø10.5 (6x)
2
86.5
R32.5
R129
R63
Ø472
6x60°
M10 (6x)
Ø252
Ø275
Ø232
±0.3
±2
-0.7
-2
+2
18
15
393
463
Ø 605
Ø 660
555
750
800
Ø 11(8x)
±3
±2
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
EC centrifugal fans – RadiCal
backward curved, Ø 630
Observe the correct mounting position!
Install the support struts only as shown in the view!
99
R3G 630-RB32-71 (Centrifugal fan)
K3G 630-RB32-71 (Centrifugal module with support bracket)
290
333
70
Ø660
Ø452
Ø458
Ø600
Ø634
Ø10.5 (6x)
2
86.5
R32.5
R129
R63
Ø472
6x60°
M10 (6x)
Ø252
Ø275
Ø232
±0.3
±2
-0.7
-2
+2
18
15
393
463
Ø 605
Ø 660
555
750
800
Ø 11(8x)
±3
±2
Depth of screw max. 25 mm
Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery
Cable gland M20x1,5 (3x):
Cable diameter
min. 4 mm, max. 10 mm,
Tightening torque 4±0.6 Nm
Tightening
torque
3.5±0.5 Nm
EC centrifugal fans – RadiCal
backward curved, Ø 630
Observe the correct mounting position!
Install the support struts only as shown in the view!
100
101
AC centrifugal fans – RadiCal
102
Material: Housing: Plastic PA 6, fibreglass-reinforced
Impeller: Plastic PA 6, fibreglass-reinforced
Rotor: Coated in black
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 42, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"
Mounting position: any
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type Motor
*2E 133 M2E 042-CA
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
p. 170
A1)
Electrical
connection
40 80 120 160 200
0 20 100806040 120
40
80
120
160
240
280
0,2 0,4 0,6 0,8 1,0
60 Hz50 Hz
11
2
3
4
3
4
2
200
cfm
qV
pfs Pa
in H2O
m3/h
Max.
input power(1)
Max.
current draw(1)
2750
2730
2700
2730
3200
3170
3100
3185
25
25
26
24
25
26
27
26
0,11
0,11
0,12
0,11
0,13
0,13
0,14
0,13
58
56
53
57
62
59
57
60
1~ 230 50 2700 26 0,12 1,5 / 400 -25..+45
1~ 230 60 3100 27 0,14 1,5 / 400 -25..+60
A
Capacitor
B
A
B
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
n
rpm
Curves:
AC centrifugal fans – RadiCal
backward curved, Ø 133
103
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
R2E 133-RA03 -01 0,6 K2E 133-RA03 -01 0,8
Capacitor
p. 161
Connection leads
p. 162
Electr. connection
p. 170
Inlet nozzle
p. 158
Guard grille
p. 160
kg kg
Drawings
p. 104
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
104
R2E 133-RA03-01 (Centrifugal fan)
K2E 133-RA03-01 (Centrifugal module with support basket)
4x90˚
Ø47±0.2
M4(4x)
56.5±1
Ø4.5(4x)
13
1
Ø129
Ø118
Ø87
Ø133
Ø93±0.2
48.5
55.5±1
2
Ø17
450+20
6
85±10
4
Ø210
450+20
45°
Ø180
±0.5
o
147±0.5
Ø195±0.5
Ø5 (4x)
o
165
6
64
6
85±10
Ø195±0.5
Depth of screw max. 4 mm
Connection line,
3 x brass lead tips crimped
Accessory part:
Inlet nozzle 09566-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
AC centrifugal fans – RadiCal
backward curved, Ø 133
105
106
*2E 190 M2E 068-BF A1)
100 200 300 400 500
0 50 250100 150 200 300
40
80
120
160
240
280
320
360
400
440
0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8
60 Hz50 Hz
1
1
2
3
4
3
4
2
200
cfm
qV
pfs Pa
in H2O
m3/h
2480
2440
2350
2435
2720
2645
2500
2615
48
49
52
50
60
62
65
63
0,22
0,22
0,23
0,22
0,27
0,27
0,29
0,27
66
63
60
62
68
66
62
65
1~ 230 50 2350 52 0,23 1,5 / 400 -25..+65
1~ 230 60 2500 65 0,29 1,5 / 400 -25..+75
A
B
Motor p. 170
A
B
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
n
rpm
Curves:
AC centrifugal fans – RadiCal
backward curved, Ø 190
Material: Housing: Plastic PA 6, fibreglass-reinforced
Impeller: Plastic PA 6, fibreglass-reinforced
Rotor: Coated in black
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"
Mounting position: any
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
107
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable (R2E)
Connection leads: Plug system (K2E)
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: R2E: CCC, GOST
K2E: CCC
R2E 190-RA26 -05
kg
1,3 K2E 190-RA26 -01
kg
1,7
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
Capacitor
p. 161
Connection leads
p. 162
Electr. connection
p. 170
Inlet nozzle
p. 158
Guard grille
p. 160
Drawings
p. 108
108
R2E 190-RA26-05 (Centrifugal fan)
K2E 190-RA26-01 (Centrifugal module with support basket)
Ø4.5 (4x)
Ø158
Ø80
6
85±10
450+20
Ø170
Ø125.5
14
1.25
Ø190
Ø132.8
68.5±1
62.5
Ø27
2
M4 (4x)
45°
4x90°
Ø58±0.2
2
o
204±0.5
79
o
225
Ø5 (4x)
Ø266±0.5
6
Ø266±0.5
Ø244±0.5
45°
Depth of screw max. 5 mm
Connection line,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 09576-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
Coded plug system AMP Universal-Mate-N-Lok
Connector housing: AMP 350 780-1
4 x plug pin: AMP 926 885-1
Mating connector (not included in the standard scope of delivery)
Connector housing: AMP 350 779-4
4 x female connector: AMP 926 884-1
PE
L
N + Capacitor
Capacitor
AC centrifugal fans – RadiCal
backward curved, Ø 190
109
110
*2E 220 M2E 068-BF A1)
100 200 300 400 500 600 700 800 900
0 400100 200 300 500
40
80
120
160
240
280
320
360
400
440
0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8
60 Hz50 Hz
1
1
3
3
2
200
4
4
cfm
qV
pfs Pa
in H2O
m3/h
2350
2240
2100
2185
2450
2220
2050
2165
80
86
88
86
100
105
107
105
0,36
0,38
0,39
0,38
0,46
0,46
0,47
0,46
68
62
60
63
69
62
60
63
1~ 230 50 2100 88 0,39 2,0 / 450 -25..+50
1~ 230 60 2050 107 0,47 2,0 / 450 -25..+60
*2E 220 M2E 068-CF A1)
1~ 230 50 2500 102 0,45 2,5 / 400 -25..+60
1~ 230 60 2650 135 0,60 2,5 / 400 -25..+75
A
B
C
D
A
B
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
Motor p. 170
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
n
rpm
Curves:
AC centrifugal fans – RadiCal
backward curved, Ø 220
Material: Housing: Plastic PA 6, fibreglass-reinforced
Impeller: Plastic PA 6, fibreglass-reinforced
Rotor: Coated in black
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"
Mounting position: any
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
111
R2E 220-RA38 -01 1,30 K2E 220-RA38 -01 2,00
200 400 600 800 1000
0 400100 200 300 500500
100
200
400
500
600
0,4 0,8 1,2 1,6 2,0
60 Hz50 Hz
1
1
3
3
2
2
300
4
4
cfm
qV
pfs Pa
in H2O
m3/h
2600
2575
2500
2580
2900
2790
2650
2795
90
95
102
95
120
130
135
125
0,40
0,43
0,45
0,42
0,53
0,56
0,60
0,55
70
66
64
67
73
68
66
69
R2E 220-RB06 -01 1,80 K2E 220-RB06 -01 2,40
C
D
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
kg kg
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable (R2E)
Connection leads: Plug system (K2E)
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: R2E 220-RA: VDE, CCC, GOST
R2E 220-RB: CCC, GOST
K2E: CCC
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
Capacitor
p. 161
Connection leads
p. 162
Electr. connection
p. 170
Inlet nozzle
p. 158
Guard grille
p. 160
Drawings
p. 112
Curves: n
rpm
Ped
W
I
A
LWA
dB(A)
112
R2E 220-RA38-01 / R2E 220-RB06-01 (Centrifugal fan)
K2E 220-RA38-01 / K2E 220-RB06-01 (Centrifugal module with support basket)
Ø5.5 (6x)
Ø242
Ø80
6
85±10
450+20
Ø252
Ø155
21
0.8
Ø220
Ø161
71±1
63.7
Ø27
2
M4 (4x)
45°
4x90°
Ø58±0.2
2
o
247.5±0.5
92
o
270
Ø5 (4x)
Ø305±0.5
7
Ø305±0.5
Ø294.5±0.5
45°
Depth of screw max. 5 mm
Connection line,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 09609-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
Coded plug system AMP Universal-Mate-N-Lok
Connector housing: AMP 350 780-1
4 x plug pin: AMP 926 885-1
Mating connector (not included in the standard scope of delivery)
Connector housing: AMP 350 779-4
4 x female connector: AMP 926 884-1
PE
L
N + Capacitor
Capacitor
AC centrifugal fans – RadiCal
backward curved, Ø 220
113
114
*2E 225 M2E 068-DF A1)
200 400 600 800 1000 1200
0 400100 200 300 700500 600
80
160
320
400
480
560
640
720
0,4 0,8 1,2 1,6 2,0 2,4 2,8
60 Hz50 Hz
1
1
3
3
2
2
240
4
4
cfm
qV
pfs Pa
in H2O
m3/h
2660
2575
2500
2590
2900
2735
2600
2750
130
145
155
145
190
205
210
200
0,57
0,64
0,68
0,63
0,83
0,89
0,92
0,88
73
72
66
69
76
73
68
71
1~ 230 50 2500 155 0,68 3,5 / 450 -25..+70
1~ 230 60 2600 210 0,92 3,5 / 450 -25..+65
A
B
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
Motor p. 170
A
B
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
n
rpm
Curves:
AC centrifugal fans – RadiCal
backward curved, Ø 225
Material: Housing: Plastic PA 6, fibreglass-reinforced
Impeller: Plastic PA 6, fibreglass-reinforced
Rotor: Coated in black
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"
Mounting position: any
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
115
R2E 225-RA92 -09 2,30 K2E 225-RA92 -01 3,40
kg kg
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable (R2E)
Connection leads: Plug system (K2E)
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: CCC
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
Capacitor
p. 161
Connection leads
p. 162
Electr. connection
p. 170
Inlet nozzle
p. 158
Guard grille
p. 160
Drawings
p. 116
116
R2E 225-RA92-09 (Centrifugal fan)
K2E 225-RA92-01 (Centrifugal module with support basket)
Ø4.5 (4x)
Ø210
Ø80
6
85±10
450+20
Ø223
Ø146
28
1.5
Ø225
Ø153.5
99±1
88.4
Ø27
2
M4 (4x)
45°
4x90°
Ø58±0.2
2
o
247.5±0.5
112
o
270
Ø5 (4x)
Ø305±0.5
7
Ø305±0.5
Ø294.5±0.5
45°
Depth of screw max. 5 mm
Connection line,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96358-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
Coded plug system AMP Universal-Mate-N-Lok
Connector housing: AMP 350 780-1
4 x plug pin: AMP 926 885-1
Mating connector (not included in the standard scope of delivery)
Connector housing: AMP 350 779-4
4 x female connector: AMP 926 884-1
PE
L
N + Capacitor
Capacitor
AC centrifugal fans – RadiCal
backward curved, Ø 225
117
118
*2E 250 M2E 068-EC A1)
200 400 600 800 1000 1200 1400 1600
0 400100 200 300 700 800500 600
100
200
400
500
600
700
800
900
0,4 0,8 1,2 1,6 2,0 2,4 2,8 3,2 3,6
60 Hz50 Hz
1
1
3
3
2
300
4
900 cfm
qV
pfs Pa
in H2O
m3/h
4
2630
2525
2500
2585
3220
2485
2450
2650
180
205
210
190
170
275
285
260
0,78
0,91
0,93
0,83
0,76
1,20
1,25
1,15
75
70
67
72
79
71
67
74
1~ 230 50 2500 210 0,93 5,0 / 400 -25..+70
1~ 230 60 2450 285 1,25 5,0 / 400 -25..+30
A
B
Ped
W
I
A
LWA
dB(A)
1
2
3
4
A
A
A
A
1
2
3
4
B
B
B
B
= max.
3η
Motor p. 170
A
B
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
n
rpm
Curves:
AC centrifugal fans – RadiCal
backward curved, Ø 250
Material: Housing: Plastic PA 6, fibreglass-reinforced
Impeller: Plastic PA 6, fibreglass-reinforced
Rotor: Coated in black
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"
Mounting position: any
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
119
R2E 250-RA50 -01 2,90 K2E 250-RA50 -01(2) 3,70
kg kg
(2) Only applicable by 50 Hz
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable (R2E)
Connection leads: Plug system (K2E)
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: R2E: CCC
Centrifugal fan
Mass of
centrifugal fan
Mass of centrifugal
module with
support basket
Centrifugal module
w. support basket
Capacitor
p. 161
Connection leads
p. 162
Electr. connection
p. 170
Inlet nozzle
p. 158
Guard grille
p. 160
Drawings
p. 120
120
R2E 250-RA50-01 (Centrifugal fan)
K2E 250-RA50-01 (Centrifugal module with support basket)
Ø4.5 (4x)
Ø240
Ø80
6
85±10
450+20
Ø255
Ø164.5
31
1.5
Ø250
Ø172.5
99±1
85
Ø27
2
M4 (4x)
45°
4x90°
Ø58±0.2
2
o
276±0.5
108.5
o
300
Ø5 (4x)
Ø340±0.5
7
Ø340±0.5
Ø322±0.5
45°
Depth of screw max. 5 mm
Connection line,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96359-2-4013
not included in the standard
scope of delivery
Mounting
dimensions:
Coded plug system AMP Universal-Mate-N-Lok
Connector housing: AMP 350 780-1
4 x plug pin: AMP 926 885-1
Mating connector (not included in the standard scope of delivery)
Connector housing: AMP 350 779-4
4 x female connector: AMP 926 884-1
PE
L
N + Capacitor
Capacitor
AC centrifugal fans – RadiCal
backward curved, Ø 250
121
122
*2E 250 M2E 074-EI A1)
1~ 230 50 2750 250 1,10 5,0 / 450 -25..+70
1~ 230 60 3100 390 1,71 5,0 / 450 -25..+55
A
B
200 400 600 800 1000 1200 1400 1600
0 400100 200 300 700 800500 600
100
200
400
500
600
700
800
900
0,4 0,8 1,2 1,6 2,0 2,4 2,8 3,2 3,6
60 Hz50 Hz
1
1
3
3
2
2
300
4
4
900 cfm
qV
pfs Pa
in H2O
m3/h
1
2
3
4
1
2
3
4
A
A
A
A
B
B
B
B
2800
2790
2750
2800
3200
3150
3100
3140
215
235
250
230
345
370
390
370
0,95
1,05
1,10
1,00
1,50
1,60
1,71
1,60
78
74
71
74
81
77
73
79
A
B
Motor p. 170
Ped
W
I
A
LWA
dB(A)
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
= max.
3η
n
rpm
Curves:
AC centrifugal fans – RadiCal
backward curved, Ø 250
Material: Impeller: Plastic PA 6, fibreglass-reinforced
Rotor: Coated in black
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
123
R2E 250-RB06 -01 4,10
kg
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, CURUS on request
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 170
Drawings
p. 124
Inlet nozzle
p. 158 ff.
124
R2E 250-RB06-01 (Centrifugal fan)
Ø90
M6(4x)
108
85
Ø164.5
1.5
31
Ø240
Ø255
Ø4.5(4x)
R28
Ø250
Ø172.5
5
Ø101
Ø75
6
85
450+20
117.8
±0.2
±10
±1
±0.3
2
Depth of screw max. 10 mm
Connection line,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 96359-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 250
125
126
400 800 1200 1600 2000 2400
2800
0 800200 400 600 160014001000 1200
100
300
400
500
600
0,4 0,8 1,2 1,6 2,0 2,4
700
2,8
800
3,2
1
1
3
3
2
2
200
4
4
cfm
qV
pfs Pa
in H2O
m3/h
1380
1340
1320
1340
2640
2555
2500
2540
73
85
90
84
440
520
570
530
0,32
0,37
0,40
0,37
0,73
0,84
0,91
0,84
66
61
55
57
84
79
73
74
A
C
*4E 280 M4E 068-DF A1)
1~ 230 50 1320 90 0,40 2,5 / 400 -25..+65
1~ 230 60 1400 125 0,55 2,5 / 400 -25..+55
*2D 280 M2D 074-GA D2)
3~ 400 50 2500 570 0,91 --- -25..+50
A
B
C
Material: Impeller: Plastic PP
Rotor: Coated in black
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"; "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
A B C
Motor p. 170 / 171
Ped
W
I
A
LWA
dB(A)
= max.
3η
1
2
3
4
1
2
3
4
A
A
A
A
C
C
C
C
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 280
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
127
200 400 600 800 1000 1200 1400 1600 1800
0 400100 200 300 800 900500 600 700 1000
20
60
80
100
120
0,20,1 0,3 0,4 0,7 0,80,5 0,6 0,9 1,0 1,1
140
160
180
200
220
240
260
280
300
1
3
2
40
4
cfm
qV
pfs Pa
in H2O
m3/h
1
2
3
4
B
B
B
B
1550
1450
1400
1470
105
120
125
115
0,45
0,50
0,55
0,50
68
62
57
60
B
R4E 280-RA28 -05(2) 2,50
R2D 280-RB06 -01(3) 5,40
Motor protection: TOP wired internally; Connection for external TOP
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Axial; Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: R4E: CCC
R2D: VDE, CURUS on request
A B C
A B C
kg
Ped
W
I
A
LWA
dB(A)
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
= max.
3η
(2) ErP 2015 (3) ErP 2013
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 170 /171
Drawings
p. 128
Inlet nozzle
p. 158 ff.
Curves:
(60 Hz)
n
rpm
128
R4E 280-RA28-05 (Centrifugal fan)
R2D 280-RB06-01 (Centrifugal fan)
127
132
Ø27
Ø187.5
Ø294
2
6
85
+20
450
Ø58
M4(4x)
8
Ø80
Ø260
Ø280
Ø180
R17
R53
Ø4.5(4x)
46
1.25
±0.2
±10
±1
Ø75
Ø
101
5
165
127
Ø
187.5
Ø
294
Ø
90
M6(4x)
6
85
+20
450
8
±10
±0.2
±1
±0.3
Ø176.7
Ø260
Ø280
1.25
46
Ø179.6
Ø4.5(4x)
R53
R17
R33
Depth of screw max. 10 mm
Connection line PFA 9G 0,5 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 28000-2-4013
not included in the standard
scope of delivery
Depth of screw max. 5 mm
Connection line PVC 4G 0,5 mm2,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 28000-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 280
129
130
200 400 600 800 1000 1200 1400 1600 1800 2000
0 400200 1200800600 1000
20
60
80
100
120
0,20,1 0,3 0,4 0,7 0,80,5 0,6 0,9 1,0 1,1
140
160
180
200
220
240
260
280
1 1
3
3
3
2
2
2
40
4
4
4
cfm
qV
pfs Pa
in H2O
m3/h
1
1
2
3
4
E
E
E
E
930
910
890
910
1390
1345
1325
1355
1425
1395
1380
1395
48
52
55
52
110
130
137
125
110
130
145
130
0,23
0,24
0,25
0,24
0,50
0,58
0,62
0,57
0,32
0,33
0,35
0,33
57
53
46
47
66
61
56
58
67
62
56
59
A
C
E
*6E 310 M6E 068-EC A1)
1~ 230 50 890 55 0,25 1,5 / 450 -25..+60
1~ 230 60 1000 69 0,31 1,5 / 450 -25..+60
A
B
*4E 310 M4E 068-EC A1)
1~ 230 50 1325 137 0,62 4,0 / 400 -25..+60
1~ 230 60 1380 185 0,82 4,0 / 400 -25..+40
C
D
*4D 310 M4D 068-EC D2)
3~ 400 50 1380 145 0,35 --- -25..+55
3~ 400 60 1550 205 0,37 --- -25..+55
E
F
Material: Impeller: Plastic PP
Rotor: Coated in black
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "B"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Motor p. 170 / 171
Ped
W
I
A
LWA
dB(A)
= max.
3η
1
2
3
4
1
2
3
4
A
A
A
A
C
C
C
C
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 310
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
131
200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
0 400200 1200 1400800600 1000
80
120
160
0,40,2 0,6 0,8 1,0 1,2 1,4
200
240
280
320
360
400
1 1
3
3
3
2
2
2
40
4
4
4
cfm
qV
pfs Pa
in H2O
m3/h
1
1
2
3
4
1
2
3
4
B
B
B
B
D
D
D
D
1
2
3
4
F
F
F
F
1085
1035
1000
1040
1580
1455
1380
1470
1635
1580
1550
1585
60
65
69
65
150
175
185
170
150
185
205
180
0,26
0,29
0,31
0,28
0,64
0,77
0,82
0,75
0,30
0,34
0,37
0,34
60
56
49
52
69
63
61
62
70
65
61
66
B
D
F
R6E 310-RA04 -01 3,40
R4E 310-RA06 -01 3,40
R4D 310-RA18 -01 3,40
kg
Ped
W
I
A
LWA
dB(A)
= max.
3η
Motor protection: TOP wired internally; Connection for external TOP
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Axial
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, CURUS on request
A B C D E F
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 170 /171
Drawings
p. 132
Inlet nozzle
p. 158 ff.
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(60 Hz)
n
rpm
132
R6E 310-RA04-01 (Centrifugal fan)
R4E 310-RA06-01 (Centrifugal fan)
141.5
Ø204
Ø80
Ø27
2
+20
450
M4 (4x)
Ø58
Ø325.5
154
6
85
8
Ø191.5
Ø280
Ø300
1.5
58.5
Ø193
Ø4.5(4x)
R71.1
R24.3
R45.4
±1
±0.2
±10
141.5
Ø204
Ø80
Ø27
2
+20
450
M4(4x)
Ø58
Ø325.5
154
6
85
8
Ø191.5
Ø280
Ø300
1.5
58.5
Ø193
Ø4.5(4x)
R71.1
R24.3
R45.4
±1
±0.2
±10
Depth of screw max. 5 mm
Connection line PVC 4G 0,5 mm2,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 31000-2-4013
not included in the standard
scope of delivery
Depth of screw max. 5 mm
Connection line PVC 4G 0,5 mm2,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 31000-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 310
133
R4D 310-RA18-01 (Centrifugal fan)
141.5
Ø204
Ø80
Ø27
2
+20
450
M4(4x)
Ø58
Ø325.5
154
6
85
8
Ø191.5
Ø280
Ø300
1.5
58.5
Ø193
Ø4.5(4x)
R71.1
R24.3
R45.4
±1
±0.2
±10
Depth of screw max. 5 mm
Connection line PVC 6G 0,5 mm2,
6 x brass lead tips crimped
Accessory part:
Inlet nozzle 31000-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 310
134
500 1000 1500 2000 2500 3000
0 400200 1200 1400 1600 1800800600 1000
80
120
160
0,40,2 0,6 0,8 1,0 1,2 1,4
200
240
280
320
360
1 1
3
33
2
22
40
4
4
4
cfm
qV
pfs Pa
in H2O
m3/h
1
905
870
830
845
1405
1375
1330
1360
1425
1405
1390
1395
70
80
85
85
200
230
270
245
205
240
270
265
0,32
0,35
0,37
0,36
0,89
1,00
1,18
1,05
0,67
0,69
0,72
0,70
60
55
48
48
72
66
61
63
72
67
62
62
A
C
D
*6E 355 M6E 074-DF A1)
1~ 230 50 830 85 0,37 2,0 / 400 -25..+60
1~ 230 60 775 105 0,46 2,0 / 400 -25..+50
A
B
*4E 355 M4E 074-GA A1)
1~ 230 50 1330 270 1,18 6,0 / 400 -25..+60
C
*4D 355 M4D 074-GA D2)
3~ 400 50 1390 270 0,72 --- -25..+60
3~ 400 60 1550 400 0,78 --- -25..+40
D
E
Motor p. 170 / 171
Ped
W
I
A
LWA
dB(A)
= max.
3η
1
2
3
4
D
D
D
D
1
2
3
4
1
2
3
4
A
A
A
A
C
C
C
C
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 355
Material: Impeller: Plastic PP
Rotor: Coated in black
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
135
500 1000 1500 2000 2500 3000 3500
0 400 1200 1600 2000800
80
120
160
0,40,2 0,6 0,8 1,0 1,2 1,4 1,6
200
240
280
320
360
400
440
480
1 1
3
3
2
2
40
4
4
cfm
qV
pfs Pa
in H2O
m3/h
1,8 2,0
1
2
3
4
1
2
3
4
B
B
B
B
E
E
E
E
985
875
775
805
1635
1590
1550
1555
96
100
105
105
295
355
400
390
0,44
0,44
0,46
0,45
0,64
0,72
0,78
0,76
62
55
48
48
75
70
66
65
B
E
R6E 355-RB20 -01 4,20
R4E 355-RB10 -01 5,60
R4D 355-RB10 -01 5,60
kg
Ped
W
I
A
LWA
dB(A)
= max.
3η
Motor protection: TOP wired internally; Connection for external TOP
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE, CURUS on request
A B C D E
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 170 /171
Drawings
p. 136
Inlet nozzle
p. 158 ff.
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(60 Hz)
n
rpm
136
R6E 355-RB20-01 (Centrifugal fan)
R4E 355-RB10-01 (Centrifugal fan)
Ø237
Ø372.5
162
190
Ø75
Ø101
5
6
85
+20
450
Ø90
M6(4x)
10
±10
±0.2
±1.5
+1.5
-0.4
Ø223.3
Ø325
Ø350
1.5
60
Ø227.1
Ø4.5(4x)
R69.5
R22.5
R43.5
+20
450
6
85
161.5
5
Ø75
Ø101
190
Ø237
Ø372.5
M6(4x)
90
Ø4.5(4x)
Ø350
1.5
60
R69.5
R43.5
R22.5
Ø223.3
Ø227.1
Ø325
10
±0.2
±10
±1.5
Depth of screw max. 10 mm
Connection line silicone 4G 0,5 mm2,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 35500-2-4013
not included in the standard
scope of delivery
Depth of screw max. 10 mm
Connection line silicone 4G 0,5 mm2,
4 x brass lead tips crimped
Accessory part:
Inlet nozzle 35500-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 355
137
R4D 355-RB10-01 (Centrifugal fan)
+20
450
6
85
161.5
5
Ø75
Ø101
190
Ø237
Ø372.5
M6(4x)
90
Ø4.5(4x)
Ø350
1.5
60
R69.5
R43.5
R22.5
Ø223.3
Ø227.1
Ø325
10
±0.2
±10
±1.5
Depth of screw max. 10 mm
Connection line silicone 9G 0,5 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 35500-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 355
138
1000 2000 3000
4000
0
200
400
0,8
100
0,4 1,6
300
1,2
500 1000 1500 2000 2500 cfm
qV
pfs Pa
in H2O
m3/h
33
3
4
4
4
111
2
2
2
915
895
880
895
1395
1360
1340
1380
1430
1410
1400
1410
130
145
155
145
370
435
470
400
405
480
515
475
0,58
0,64
0,68
0,63
1,95
2,20
2,33
2,05
1,10
1,15
1,19
1,15
69
62
55
55
---
---
---
---
81
75
67
67
A
C
E
*6E 400 M6E 094-FA A2a)
1~ 230 50 880 155 0,68 5,0 / 450 -40..+60
1~ 230 60 970 215 0,95 5,0 / 450 -40..+60
A
B
*4E 400 M4E 094-HA A2a)
1~ 230 50 1340 470 2,33 9,0 / 400 -40..+60
1~ 230 60 1430 650 3,00 9,0 / 400 -40..+45
C
*4D 400 M4D 094-HA F1a)
3~ 400 50 1400 515 1,19 --- -40..+60
3~ 400 60 1580 770 1,35 --- -40..+40
E
F
Motor p. 170 / 171
Ped
W
I
A
LWA
dB(A)
= max.
3η
1
2
3
4
E
E
E
E
1
2
3
4
1
2
3
4
A
A
A
A
C
C
C
C
D
Material: Impeller: Plastic PP
Rotor: Coated in black
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Any
Condensate discharges: None
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 400
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
1000 2000 3000 4000 5000
0
200
400
0,8
100
0,4
300
1,2
500
2,01,6
600
2,4
1000 1500 2000 30002500500
3
3
4
4
2
2
1 11
cfm
qV
pfs Pa
in H2O
m3/h
2
3
4
139
B
F
R6E 400-RN06 -01 7,40
R4E 400-RO09 -01 8,50
R4D 400-RO22 -01 8,80
kg
Ped
W
I
A
LWA
dB(A)
D
1055
1005
970
1020
1585
1470
1430
1535
1645
1605
1580
1605
195
210
215
205
525
625
650
575
600
715
770
700
0,85
0,91
0,95
0,90
2,35
2,90
3,00
2,60
1,10
1,25
1,35
1,25
70
64
57
59
---
---
---
---
85
79
72
73
1
2
3
4
F
F
F
F
1
2
3
4
1
2
3
4
B
B
B
B
D
D
D
D
= max.
3η
Motor protection: Connection for external TOP
Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: CCC
A B C D
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 170 /171
Drawings
p. 140
Inlet nozzle
p. 158 ff.
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(60 Hz)
n
rpm
140
R6E 400-RN06-01 (Centrifugal fan)
R4E 400-RO09-01 (Centrifugal fan)
345
257
1.5
66
370
115
R
90
R
50
4.5
(4x)
266
420
100
130
5.5
194
6
85
600
182
45°
4x90°
M6 (4x)
Ø
±0.5
Ø
Ø
Ø
±1
±10
+20
Ø
±0.2
Ø
Ø
Ø
Ø
10
345
257
1.5
66
370
115
R
90
R
50
4.5
(4x)
266
420
100
130
5.5
194
6
85
600
182
45°
4x90°
M6 (4x)
Ø
±0.5
Ø
Ø
Ø
±1
±10
+20
Ø
±0.2
Ø
Ø
Ø
Ø
10
Depth of screw max. 12 mm
Connection line silicone 6G 0,5 mm2,
6 x brass lead tips crimped
Accessory part:
Inlet nozzle 54476-2-4013
not included in the standard
scope of delivery
Depth of screw max. 12 mm
Connection line silicone 6G 0,5 mm2,
6 x brass lead tips crimped
Accessory part:
Inlet nozzle 54476-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 400
141
R4D 400-RO22-01 (Centrifugal fan)
345
257
1.5
66
370
115
R
90
R
50
4.5
(4x)
266
420
100
130
5.5
194
6
85
600
182
45°
4x90°
M6 (4x)
Ø
±0.5
Ø
Ø
Ø
±1
±10
+20
Ø
±0.2
Ø
Ø
Ø
Ø
10
Depth of screw max. 12 mm
Connection line silicone 9G 0,5 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 54476-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 400
142
Material: Impeller: Plastic PP
Rotor: Cast in aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request
Condensate discharges: Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
*6E 450 M6E 110-EF A1)
1~ 230 50 940 285 1,35 8,0 / 450 -40..+60
A
*4E 450 M4E 110-GF A1)
1~ 230 50 1260 690 3,10 14,0 / 450 -40..+55
B
*4D 450 M4D 110-GF D2)
3~ 400 50 1350 710 1,45 --- -40..+60
C
Motor p. 170 / 171
1000 2000 3000 4000 5000
0 500 1500 2000 2500 30001000
1,20,4
100
0,8
200
1 1
3
2
4
3
4
2
3
2
4
1
cfm
qV
pfs Pa
in H2O
m3/h
300
1,6
300
2,0
500 960
950
940
945
1365
1310
1260
1295
1405
1370
1350
1370
230
260
285
270
545
630
690
650
495
645
710
650
1,15
1,25
1,35
1,30
2,40
2,75
3,10
2,85
1,15
1,30
1,45
1,30
68
65
62
63
77
74
69
71
77
75
70
73
A
B
C
Ped
W
I
A
LWA
dB(A)
= max.
3η
1
2
3
4
C
C
C
C
1
2
3
4
1
2
3
4
A
A
A
A
B
B
B
B
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 450
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 230 or 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
143
R6E 450-RG01 -01 12,0
R4E 450-RH01 -01 12,0
R4D 450-RH01 -01 9,40
kg
Motor protection: Connection for external TOP
Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 61800-5-1, CE EN 60034, CE
Approvals: VDE, CCC, GOST, UL, CSA
A B C
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 170 /171
Drawings
p. 144
Inlet nozzle
p. 158 ff.
144
R6E 450-RG01-01 (Centrifugal fan)
R4E 450-RH01-01 (Centrifugal fan)
300
485
100
130
142
Ø115
4x90°
45°
M6 (4x)
286.7
292
425
450
3
50
Ø9(6x)
240
5.5
218
800
80
6
438.9
140
R40
R50
R20
±3
Ø
Ø
Ø
Ø
Ø
+20
±10
±0.5
Ø
±0.3
Ø
Ø
Ø
Ø
10
300
485
100
130
142
Ø115
4x90°
45°
M6 (4x)
286.7
292
425
450
3
50
Ø9(6x)
240
5.5
218
800
80
6
438.9
140
R40
R50
R20
±3
Ø
Ø
Ø
Ø
Ø
+20
±10
±0.5
Ø
±0.3
Ø
Ø
Ø
Ø
10
Depth of screw max. 12 mm
Connection line silicone 6G 0,5 mm2,
6 x brass lead tips crimped
Accessory part:
Inlet nozzle 45901-2-2943
not included in the standard
scope of delivery
Depth of screw max. 12 mm
Connection line silicone 6G 0,75 mm2,
6 x brass lead tips crimped
Accessory part:
Inlet nozzle 45901-2-2943
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 450
145
R4D 450-RH01-01 (Centrifugal fan)
300
485
100
130
142
Ø115
4x90°
45°
M6 (4x)
286.7
292
425
450
3
50
Ø9(6x)
240
5.5
218
800
80
6
438.9
140
R40
R50
R20
±3
Ø
Ø
Ø
Ø
Ø
+20
±10
±0.5
Ø
±0.3
Ø
Ø
Ø
Ø
10
Depth of screw max. 12 mm
Connection line silicone 9G 0,75 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 45901-2-2943
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 450
146
1000 2000 3000 4000 5000 6000 7000 8000 9000
0 1000 3000 4000 50002000
100
200
0,4 0,8 1,2 1,6 2,0 2,4
300
400
500
600
700
800
1
3
2
4
cfm
qV
pfs Pa
in H2O
m3/h
2,8
1410
1390
1370
1380
1125
1350
1520
1385
2,45
2,70
2,91
2,75
81
77
73
73
A
*4D 500 M4D 138-HF D2)
3~ 400 50 1370 1520 2,91 --- -40..+70
A
Material: Impeller: Plastic PP
Rotor: Cast in aluminium
Number of blades: 7
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Any
Condensate discharges: Rotor- and stator-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
Motor p. 171
Ped
W
I
A
LWA
dB(A)
= max.
3η
1
2
3
4
A
A
A
A
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 500
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
147
R4D 500-RA03 -01 21,5
kg
Motor protection: Connection for external TOP
Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Lateral
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60034, EN 61800-5-1, CE
Approvals: VDE, GOST
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 171
Drawings
p. 148
Inlet nozzle
p. 158 ff.
148
R4D 500-RA03-01 (Centrifugal fan)
22.5°
8x45°
M10 (8x)
162
1000
85
6
12
R28
R87
R49
445
470
320
3.5
75
9 (6x)
334.5
525
140
190
5.5
227
295.5
Ø ±0.2
+20
±10
Ø ±0.5
Ø
±2
Ø
Ø
Ø
Ø
Ø
Ø
Depth of screw max. 18 mm
Connection line halogen-free 9 x 0,75 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 50901-2-2943
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 500
149
150
Material: Impeller: Plastic PP
Rotor: Cast in aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54
Insulation class: "F"
Mounting position: Any
Condensate discharges: Rotor- and stator-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
*4D 560 M4D 138-LA D2)
3~ 400 50 1390 1950 3,98 --- -40..+60
3~ 400 60 1560 2990 5,16 --- -40..+40
A
B
2000 4000 6000 8000 10000 12000
0 1000 2000 4000 5000 700060003000
3
4
2
11
200
0,8
400
1,6
600
2,4
800
3,2
1000
4,0
cfm
qV
pfs Pa
in H2O
m3/h
3
4
2
1
2
3
4
1
2
3
4
A
A
A
A
B
B
B
B
1425
1405
1390
1400
1635
1590
1560
1585
1475
1780
1950
1850
2275
2730
2990
2785
3,45
3,75
3,98
3,85
4,05
4,75
5,16
4,80
85
81
78
79
88
84
81
83
A
B
Motor p. 171
Ped
W
I
A
LWA
dB(A)
= max.
3η
n
rpm
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz)
AC centrifugal fans – RadiCal
backward curved, Ø 560
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
151
R4D 560-RB03 -01 25,5
kg
Motor protection: Connection for external TOP
Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Lateral
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60034, EN 61800-5-1, CE
Approvals: VDE, GOST
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 171
Drawings
p. 152
Inlet nozzle
p. 158 ff.
152
R4D 560-RB03-01 (Centrifugal fan)
Ø 418
Ø 567
253
289
5.5
Ø 140
Ø 190
Ø 540
Ø 565
Ø9 (6x)
Ø 407
1.5
83.5
R50
Ø 162
M10(8x)
22.5°
8x45°
1000
85
±0.2
±0.7
±2
+20
±10
18
Depth of screw max. 18 mm
Connection line halogen-free 9 x 0,5 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 54482-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 560
153
154
2000 4000 6000 8000 10000 12000 14000 16000
0 2000 6000 8000
10000
4000
100
200
0,4 0,8 1,2 1,6 2,0 2,4
300
400
500
600
700
1
3
2
4
1
3
2
4
cfm
qV
pfs Pa
in H2O
m3/h
2,8
800
3,2
925
895
880
885
1400
1360
1345
1350
735
935
1030
995
2570
3315
3570
3395
1,85
2,10
2,20
2,15
5,15
6,25
6,63
6,35
79
73
71
72
90
84
81
83
A
C
*6D 630 M6D 138-HF D2)
3~ 400 50 880 1030 2,20 --- -40..+60
3~ 400 60 940 1440 2,81 --- -40..+60
A
B
*4D 630 M4D 138-LA D2)
3~ 400 50 1345 3570 6,63 --- -40..+40
C
Material: Impeller: Plastic PP
Rotor: Cast in aluminium
Number of blades: 6
Direction of rotation: Clockwise, seen on rotor
Type of protection: IP 54, IP 20
Insulation class: "F"
Mounting position: Any
Condensate discharges: Rotor- and stator-side, Rotor-side
Mode of operation: Continuous operation (S1)
Bearings: Maintenance-free ball bearings
A B C
A B C
Motor p. 171
n
rpm
Ped
W
I
A
LWA
dB(A)
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(50 Hz) = max.
3η
1
2
3
4
1
2
3
4
A
A
A
A
C
C
C
C
AC centrifugal fans – RadiCal
backward curved, Ø 630
Nominal data
Type
subject to alterations (1) Nominal data in operating point with maximum load and 400 VAC
VAC Hz rpm W A μF/VDB °C
Curve
Nominal voltage
Frequency
Speed/rpm(1)
Perm. amb. temp.
Electrical
connection
Max.
input power(1)
Max.
current draw(1)
Capacitor
155
2000 4000 6000 8000 10000 12000
0 1000 3000 40002000 6000 70005000
40
80
0,4 0,8 1,2 1,6
120
160
200
240
280
1
3
2
4
cfm
qV
pfs Pa
in H2O
m3/h
320
360
400
480
440 1
2
3
4
B
B
B
B
1030
970
940
945
1090
1340
1440
1410
2,20
2,65
2,81
2,75
83
75
72
73
B
R6D 630-RA07 -01 25,0
R4D 630-RB15 -01 28,0
kg
Ped
W
I
A
LWA
dB(A)
= max.
3η
Motor protection: Connection for external TOP
Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Lateral
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60034, EN 61800-5-1, CE
Approvals: VDE, GOST
Centrifugal fan
Mass of
centrifugal fan
Guard grille
p. 160
Capacitor
p. 161
Electr. connection
p. 171
Drawings
p. 156
Inlet nozzle
p. 158 ff.
Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection
against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis.
The acoustic values given are only valid under the measurment conditions listed and may vary depending on the instal-
lation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once
installed or fitted! For detailed information see page 172 ff.
Curves:
(60 Hz)
n
rpm
156
R6D 630-RA07-01 (Centrifugal fan)
R4D 630-RB15-01 (Centrifugal fan)
18
600
452
457
R63.2
R129
R32.5
10.5 (6x)
634
2
86.5
472
660
605
190
140
22,5°
8x45°
162
1000
85
6
M10 (8x)
5.5
290
333
+20
±10
±0.2
Ø
Ø
Ø
Ø
Ø
Ø
±0.7
±2
Ø
Ø
Ø
Ø
Ø
18
600
452
457
R63.2
R129
R32.5
10.5 (6x)
634
2
86.5
472
660
605
190
140
22,5°
8x45°
162
1000
85
6
M10 (8x)
5.5
290
333
+20
±10
±0.2
Ø
Ø
Ø
Ø
Ø
Ø
±0.7
±2
Ø
Ø
Ø
Ø
Ø
Depth of screw max. 18 mm
Connection line halogen-free 9 x 0,75 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 63300-2-4013
not included in the standard
scope of delivery
Depth of screw max. 18 mm
Connection line halogen-free 9 x 0,75 mm2,
9 x brass lead tips crimped
Accessory part:
Inlet nozzle 63300-2-4013
not included in the standard
scope of delivery
AC centrifugal fans – RadiCal
backward curved, Ø 630
157
4x90°
Size
133
190
220
225
250
280
310
355
400
450
500
560
630
Dimensions
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
subject to alterations * Material: Plastic ABS
- Material: galvanised sheet steel
Inlet nozzles without measuring device for backward curved centrifugal fans
158
Part no.
09566-2-4013
09576-2-4013
09609-2-4013
96358-2-4013
96359-2-4013
28000-2-4013
31000-2-4013
35500-2-4013
54476-2-4013
45901-2-2943 *
50901-2-2943 *
54482-2-4013
63300-2-4013
6x60°
Vers.
1
1
2
1
1
1
1
1
1
2
2
2
2
Vers. 1 Vers. 2
Inlet nozzles
Effects of installation space
When mounting our product in a rectangular box, air performance
might be reduced.
dh= Hydraulic diameter
Formula: dh= 2 x B x H / (B + H)
B = Width of box
H = Height of box
D = Outer diameter of the fan
1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8
Hydraulic diameter dh/D
Correction factor for air flow
1,000,990,980,970,960,950,940,930,92
Curve:
D
H
B
0,5
x
D
D
D
k-value
60
77
93
128
180
190
260
405
515
Inlet nozzles with measuring device to determine air flow for backward curved centrifugal fans
Size
250
280
310
355
400
450
500
560
630
Dimensions
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
see corresponding product page
subject to alterations * Material: Plastic ABS
- Material: galvanised sheet steel
159
Part no.
96400-2-4013
28003-2-4013
31003-2-4013
35503-2-4013
54501-2-4013
45910-2-2943 *
50920-2-2943 *
54492-2-4013
63310-2-4013
With piezometer ring
Inlet nozzles with measuring device
Δp
0,5
x
D
D
The differential pressure approach compares the static pressure before the
inlet nozzle with the static pressure inside the inlet nozzle. Air flow can be
calculated on the basis of the differential pressure (difference in pressure of
the static pressures) in keeping with the following equation:
qV= k .
Δpq
Vin [m3/h] und Δp in [Pa]
If constant air flow is to be controlled to, then the nozzle pressure has to be
kept constant:
Δp = qV2: k2
k takes into account the specific nozzle characteristics.
Differences in static pressure are measured in 1/4 measuring point(s) along
the circumference of the inlet nozzle. Connection on the customer side is
acomplished via a pre-mounted T tube connector. This tube connector is
suited for pneumatic hoses with an internal diameter of 4 mm.
Air flow determination
160
a
e
Ød
b
e
Ød
b
a
- Material: steel wire, plastic coated
Vers. 1 Vers. 2
ab
Guard grille for suction side for compact centrifugal modules
Part no. Size
13351-2-2929 133
ab
94,1 7,7
19051-2-2929 190 133,0 9,0
22051-2-2929 220 166,0 8,7
22551-2-2929 225 158,0 8,7
25051-2-2929 250 177,0 9,7
- Material: PA plastic 6, fibreglass-reinforced
subject to alterations
Air intake guard grilles
Part no.
78128-2-4039
78129-2-4039
78130-2-4039
78131-2-4039
78132-2-4039
78136-2-4039
78139-2-4039
78138-2-4039
Size
250
280
310
355
400
450
500
630
Vers.
1
1
1
1
1
2
2
2
a b d e Strut pitch
240 5,4 208 2,4 4 x 90°
260 4,5 210 2,8 4 x 90°
280 4,5 230 2,8 4 x 90°
325 4,5 250 2,8 4 x 90°
345 4,5 310 2,8 4 x 90°
425 8,5 350 3,8 3 x 120°
445 8,5 410 3,8 3 x 120°
600 8,5 490 3,8 3 x 120°
subject to alterations
Air intake guard grilles for backward curved centrifugal fans (according to EN ISO 13857)
The table has been changed with respect
to the printed edition of the catalogue.
161
235
735
M8
a
10 b
c
a + 3,5
Ø
+10
-5
Ø
+5
±1
max. 9 mm
- Material: Plastic cap, aluminium cup
- Designation: FPU or P2 according to
IEC 252 (non-flammable, non-explosive,
circuit-breaking)
- Approval: VDE according to DIN EN 60252
(VDE 0560/8)
- Calculated life time:
420 V; -25 to +85°C; 30,000 hrs; class A
470 V; -25 to +85°C; 10,000 hrs; class B
500 V; -25 to +85°C; 3,000 hrs; class C
MKP motor capacitors FPU or P2 (with fuse)
Part no. ab(max.) c(max.)
subject to alterations
Capacity
02155-4-7320 25,0 77,0 92,0
02156-4-7320 25,0 77,0 92,0
02159-4-7320 30,0 71,0 92,0
02179-4-7320 30,0 75,0 82,0
02161-4-7320 25-30 104,0 135,0
02162-4-7320 25-30 104,0 113,0
1,5 μF
2,0 μF
2,5 μF
3,5 μF
4,0 μF
5,0 μF
02163-4-7320 30,0 101,0 110,06,0 μF
Capacitors
- Pull-off protector: The housing expands
by max. 9 mm. The protector responds to over-
load by the generated excess pressure snapping
off the internal lead in a predetermined break-
ing point.
02165-4-7320 30-35 102,0 111,08,0 μF
90026-4-7320 40,0 130,0 139,014,0 μF
- Mounting: c is the overall dimension of the
capacitor which has to be taken into account
when mounting the part. The capacitor de-
sign, however, depends on the manufacturer.
The expansion (9 mm) is either added to di-
mension b, or it is already integrated in the
capacitor.
c
M8
a
10 b
Ø
7±1
±10 - Material: Housing made of thermoplastic resin
- Connection line: Multi-lead
PVC cable 0.5 mm2with brass lead tips
- Approval: VDE according to DIN EN 60252
(VDE 0560/8)
- Calculated life time:
400 V; -25 to +85°C; 30,000 hrs; class A
450 V; -25 to +85°C; 10,000 hrs; class B
MKP motor capacitors P0 (without fuse)
Part no. ab(max.) c
subject to alterations
Capacity
99832-4-7320 35,0 70,0 100,09,0 μF
162
85
a
6
Lead connections for AC centrifugal modules (230 V)
Part no.
23030-4-1012
a
450,0
23031-4-1012 1000,0
23032-4-1012 1300,0
23033-4-1012 1600,0
subject to alterations
23034-4-1012 2300,0
- Plug assignment:
1 = green/yellow
2 = blue
3 = brown
4 = not assigned
Connector shell AMP 350 779-4
Jacketed cable, internal leads
H03VV-F3G0,5 black
Brass lead tips
3 x female terminal AMP 926 884-1
Connection leads
230 V
163
Imax=1.1mA
1μF
Line Connection Colour Assignment / function
2 L brown Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range
3 N blue Neutral conductor
Customer circuit Connection Fan
2
1PE green/yellow Protective earth
70-10V PWM yellow Control input 0 - 10 V or PWM, electrically isolated
5Tach white Tach output: Open Collector, 1 pulse per revolution, electrically isolated, Isink max=10mA
610V/max.1.1mA red Voltage output 10 V / 1.1 mA, electrically isolated
4GND blue GND - Connection for control interface
3
1
6
7
4
5
680R
ZMM47
13
24
47k 47k
PE1
AC1 P
AC2 N
L
N
PE
+10V
10V/PWM
GND
Tach
max.
speed
Speed
setting
4
7
7
6
10V -> n = max
1V -> n = min
<1V -> n = 0
1-10V
Speed
setting with
PWM 1-10kHz
Speed
setting with
potentiometer
4
7
6
10K
15V
4
7
12V
Imax=10mA
100% PWM -> n = max
10% PWM -> n = min
<10% PWM -> n = 0
Technical features (M3G 055 Speed-controlled):
Output 10 VDC max. 1,1 mA
Tach output
Over-temperature protected motor
Motor current limitation
Locked-rotor protection
Soft start
Control interface with SELV potential safely disconnected from the mains
3,15AT
Electrical connections EC
H5)
164
Line Connection Colour Assignment / function
CON10 Lblack Power supply 230 VAC, 50 - 60 Hz
CON11 Nblue Neutral conductor
CON10
Customer circuit Connection Fan
CON70
CON11
CON70
CON10
CON11
CON70
CON12
L
N
SL
PE
PE1
AC1
AC2
P
N
CON12 PE green/yellow Protective earth
CON70 SL brown Speed selection: switch open = speed 1; switch closed = speed 2
Technical features (M3G 045 / M3G 055 with 2 Speed stages):
Speed adjustment input (230V)
Over-temperature protected electronics / motor
Motor current limitation
Locked-rotor protection
Soft start
Electrical connections EC
H3)
165
Imax=1.1mA
1μF
Line Connection Colour Assignment / function
CON10 Lblack Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range
CON11 Nblue Neutral conductor
Customer circuit Connection Fan
CON10
CON12 PE green/yellow Protective earth
1GND blue GND - Connection for control interface
20-10V PWM yellow Control input 0 - 10 V or PWM, electrically isolated
310V/max.1.1mA red Voltage output 10 V / 1.1 mA, electrically isolated, not short-circuit-proof
4Tach white Tach output: Open Collector, 1 pulse per revolution, electrically isolated
CON11
CON12
3
2
1
4
680R
ZMM47
13
24
47k 47k
PE1
31
42
AC1 P
AC2 N
L
N
PE
+10V
10V/PWM
GND
Tach
max.
speed
Speed
setting
1
2
2
3
10V -> n = max
1V -> n = min
<1V -> n = 0
1-10V
Speed
setting with
PWM 1-10kHz
Speed
setting with
potentiometer
1
2
3
10K
15V
1
2
12V
Imax=10mA
100% PWM -> n = max
10% PWM -> n = min
<10% PWM -> n = 0
Technical features (M3G 045 / M3G 055 Speed-controlled; M3G 074):
Control input 0-10 VDC / PWM
Output 10 VDC max. 1,1 mA
Tach output
Over-temperature protected electronics / motor
Motor current limitation
Locked-rotor protection
Soft start
Electrical connections EC
H4)
166
Technical features:
PFC (aktive) Motor current limitation, Alarm relay
integrated PID controller Line undervoltage / phase failure detection
Control input 0-10 VDC / PWM Over-temperature protected electronics / motor
Output 10 VDC max. 10 mA Locked-rotor protection, Soft start
Operation and alarm display Control interface with SELV potential safely disconnected from the mains
RS485 MODBUS RTU
RSA
11 RSA
Speed
Full
potentiometer
setting with
Speed
<1 V -> n = 0
1 V -> n = min
10 V -> n = max
setting
Speed
1-10 V
10 K
47 K
Imax=10 mA
10
47 K
PE1
A2
A1
14
11
470 nF
L
N
GND
PE
10 V
0-10 V
NC
COM
8
8
88
7
6
5
3
2
PE
1
12
12
12
13
13
13
10 V
0 V
0-10
V
RSB
10 RSB
Customer circuit Connection Fan
N
PE
Line Connection Colour Assignment / function
1PE green/yellow Protective earth
1
1
1
Nblue Supply voltage, neutral conductor, see type plate for voltage range, 50/60 Hz
Line 1
blackblue
0-10 V
Line 2
yellow
Lblack Supply voltage, phase, see type plate for voltage range, 50/60 Hz
NC white 1 Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side
L
RSB
NC
white 1 brown
COM
white 2green/yellow
RSA
white
No.
1, 2
3
5
6
1COM white 2 Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side
7
20-10 V yellow Analogue input (set value), SELV 0-10 V, Impedance 100 kΩ, parametrisable curve
8
2RSB brown RS485 interface for MODBUS, RSB, SELV10
2RSA white RS485 interface for MODBUS, RSA, SELV11
GND
blue
+10 V
red
2GND blue Reference ground for control interface, SELV12
2+10 V red Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof,
Power supply for external devices (e.g. potentiometer)
13
Electrical connections EC
P5)
167
Technical features:
PFC (passive) Motor current limitation, Alarm relay
integrated PID controller Line undervoltage / phase failure detection
Control input 0-10 VDC / PWM Over-temperature protected electronics / motor
Output 10 VDC max. 10 mA Locked-rotor protection, Soft start
Operation and alarm display Control interface with SELV potential safely disconnected from the mains
RS485 MODBUS RTU
RSA
11 RSA
Speed
Full
potentiometer
setting with
Speed
<1 V -> n = 0
1 V -> n = min
10 V -> n = max
setting
Speed
1-10 V
10 K
47 K
Imax=10 mA
10
47 K
PE1
A2
A1
14
11
470 nF
L3
L1
GND
PE
10 V
0-10 V
NC
COM
8
8
88
7
6
5
L2
4
3
2
PE
1
12
12
12
13
13
13
10 V
0 V
0-10
V
RSB
10 RSB
Customer circuit Connection Fan
L1
PE
Line Connection Colour Assignment / function
1PE green/yellow Protective earth
1
1
Line 1
blackblack
0-10 V
Line 2
yellow
L1, L2, L3 black Supply voltage, see type plate for voltage range, 50/60 Hz
NC white 1
L2
RSB
NC
white 1 brown
COM
white 2green/yellow
RSA
white
No.
1, 2
3, 4, 5
6
1COM white 27
20-10 V yellow8
2RSB brown10
2RSA white11
GND
blue
+10 V
red
2GND blue12
2+10 V red
13
black
L3
Electrical connections EC
P6)
Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side
Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side
Analogue input (set value), SELV 0-10 V, Impedance 100 kΩ, parametrisable curve
RS485 interface for MODBUS, RSB, SELV
RS485 interface for MODBUS, RSA, SELV
Reference ground for control interface, SELV
Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof,
Power supply for external devices (e.g. potentiometer)
Connector Connection Assignment / function
PE
KL3
PE Earth connection, PE connection
+10 V
KL1 NMains supply connection, supply voltage 1~200-277 VAC, 50/60 Hz
L1 Mains supply connection, supply voltage 1~200-277 VAC, 50/60 Hz
Signal ground for control interface
Ain2 I
Signal ground for control interface
Ain1U
RSB
GND
RSA
Aout
Bus connection RS485; RSB; MODBUS RTU
+20 V
Bus connection RS485; RSA; MODBUS RTU
GND
Fixed voltage output 10 VDC; +10 V ±3 %; max. 10 mA; short circuit proof; power supply for ext. devices (e.g. potentiometer)
Analogue output 0-10 V; max. 5 mA; output of the actual motor control factor (output voltage of electronics)/of the actual motor speed;
parametrisable curve
Din2
Din3
GND
Ain2 U
+20 V
Ain2 I
Aout
KL3 KL2 KL1
RS A
RS B
GND
Ain1 U
+10 V
Ain1 I
Din1
NO
COM
NC
PE
L1
N
Analogue input 1 (set value); 0-10 V; Ri= 100 kΩ; parametrisable curves; only usable as alternative to input Ain1 I
Analogue input 2; actual sensor value 4-20 mA; Ri= 100 Ω; parametrisable curve; only useable as alternative to input Ain2 U
Fixed voltage output 20 VDC; +20 V +25/-10 %; max. 50 mA; short circuit proof; power supply for ext. devices (e.g. sensors)
Din1
Ain1 I Analogue input 1 (set value); 4-20 mA; Ri= 100 Ω; parametrisable curve; only usable as alternative to input Ain1 U
Digital input 1: enabling of electronics; enabling: open pin or applied voltage 5 to 50 VDC; disabling: bridge to GND or
applied voltage < 0,8 VDC; reset function: triggers software reset after a level change to < 0,8 V
Ain2 U Analogue input 2; actual sensor value 0-10 V; Ri= 100 kΩ; parametrisable curve; only useable as alternative to input Ain2 I
Din3 Digital input 3: Control characteristic of the integrated controller; according to EEPROM setting, the control characteristic of the integrated control-
ler is normally/inversely selectable per BUS or per digital input; normal: open pin or applied voltage 5 to 50 VDC; inverse: bridge to GND or applied
voltage < 0,8 VDC
Din2 Digital input 2: parameter set switch 1/2; according to EEPROM setting, thr valid/used parameter set is selectable per BUS or per
digital input Din2. Parameter set 1: open pin or applied voltage 5 to 50 VDC; parameter set 2: bridge to GND or applied voltage < 0,8 VDC
Technical features:
PFC (aktive) Tach output Control interface with SELV potential
integrated PID controller RS485 MODBUS-RTU safely disconnected from the mains
Control input 0-10 VDC / PWM Alarm relay
Input for sensor 0-10 V bzw. 4-20 mA Line undervoltage / phase failure detection
External 24 V input (programming) Motor current limitation
External release input Output limit
Output for slave 0-10 V max. 3 mA Over-temperature protected electronics / motor
Output 20 VDC (±20 %) max. 50 mA Reverse polarity and locked-rotor protection
Output 10 VDC (+10 %) max. 10 mA Soft start
168
KL2
COM
NC
NO
Electrical connections EC
M4)
Status relay, floating status contact, changeover contact, common connection, contact rating 250 VAC / 2 A (AC1)
Status relay, floating status contact, option 1: break with error, option 2: break with error for run monitor error message
Status relay, floating status contact, option 1: close with error, option 2: close with run monitor error message
169
Connector Connection Assignment / function
PE PE Earth connection, PE connection
KL1 L1 Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
L2 Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
L3 Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz
Din1
+10 V
Ain1 U
NC
KL2 KL1
RS A
RS B
GND
C
PE
L1
L2
L3
1 2 3 4 1 2 3
5 6 7 8
Pin
1
2
3
RSB Bus connection RS485; RSB; MODBUS RTU
RSA
GND
Bus connection RS485; RSA; MODBUS RTU
Signal ground for control interface
4
5
6+10 V Fixed voltage output 10 VDC; +10 V ±3 %; max. 10 mA; short circuit proof; power supply for ext. devices (e.g. potentiometer)
Ain1 U Analogue input 1 (set value); 0-10 V; Ri= 100 kΩ; parametrisable curves
7
8
Technical features:
PFC (passive) Motor current limitation
integrated PID controller Alarm relay
Control input 0-10 VDC / PWM Line undervoltage / phase failure detection
External release input Over-temperature protected electronics / motor
External 24 V input (programming) Reverse polarity and locked-rotor protection
Output 10 VDC max. 10 mA Soft start
Operation and alarm display Control interface with SELV potential safely disconnected from the mains
RS485 MODBUS-RTU
KL2
NC Status relay, floating status contact, break with error
1
2
3
Status relay, floating status contact, changeover contact, common connection 250 VAC / 2 A (AC1)C
Din1 Digital input 1: enabling of electronics; enabling: open pin or applied voltage 5 to 50 VDC; disabling: bridge to GND or
applied voltage < 1 VDC; reset function: triggers software reset after a level change to < 1V
Electrical connections EC
M5)
170
A1) Single-phase capacitor motor (1~ 230 VAC power line)
with TOP wired internally
C
N
PE
L
TOP
2
1ZU
U
U1= blue
U2= black
Z = brown
= green/yellow
A2a) Single-phase capacitor motor (1~ 230 VAC power line)
with connection for external TOP
C
N
PE
L
2
1ZU
U
TOP
U1= blue
U2= black
Z = brown
= green/yellow
Electrical connections AC
A1) / A2a)
171
D2) Star connection (3~ 400 VAC power line)
with TOP
L3 TOPL2L1
1
2
V
1
U
1
2
V
2
UW
W
PE
U1= black
U2= green
V1= blue
V2= white
W1= brown
W2= yellow
= green/yellow
Direction of rotation is reversed by swapping
two line phases.
F1a) Delta connection (3~ 400 VAC power line)
with TOP
L3L2L1
W
22
V
2
U
1
U
1
V
1
W
PE TOP
U1= blue
U2= green
V1= blue
V2= white
W1= brown
W2= yellow
= green/yellow
Direction of rotation is reversed by swapping
two line phases
Electrical connections AC
D2) / F1a)
172
General performance parameters
Any deviations from the technical data and parameters described here
are listed on the product-specific data sheet.
Type of protection
The type of protection is specified in the product-specific data sheets.
Insulation class
The insulation class is specified in the product-specific data sheets.
Mounting position
The mounting position is specified in the product-specific data sheets.
Condensate discharge holes
Information on the condensate discharge holes is provided in the
product-specific data sheets.
Mode of operation
The mode of operation is specified in the product-specific data sheets.
Protection class
The protection class is specified in the product-specific data sheets.
Service life
The service life of ebm-papst products depends on two major factors:
The service life of the insulation system
The service life of the bearing system
The service life of the insulation system mainly depends on voltage level,
temperature and ambient conditions, such as humidity and condensation.
The service life of the bearing system depends mainly on the thermal load
on the bearing.
The majority of our products use maintenance-free ball bearings for
any mounting position possible. As an option, sleeve bearings can be
used, which is indicated on the product-specific data sheet wherever
applicable.
The service life L10 of the ball bearings can be taken as approx. 40,000
operating hours at an ambient temperature of 40 °C, yet this estimate
can vary according to the actual ambient conditions.
We will gladly provide you with a lifetime calculation taking into account
your specific operating conditions.
Motor protection / thermal protection
Information on motor protection and thermal protection is provided in the
product-specific data sheets.
Depending on motor type and field of application, the following protective
features are realised:
Thermal overload protection (TOP), either in-circuit or external
PTC with electronic diagnostics
Impedance protection
Thermal overload protection (TOP) with electronic diagnostics
Current limitation via electronics
If an external TOP is connected, the customer has to make sure to
connect a conventional trigger device for switching it off.
Products without fitted TOP and without protection against improper use,
a motor protection complying with the valid standards has to be installed.
Mechanical strain / performance parameters
All ebm-papst products are subjected to comprehensive tests complying
with the normative specifications. In addition to this, the tests also reflect
the vast experience and expertise of ebm-papst.
High standards for all ebm-papst products
Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best possible product for your application.
Careful monitoring of the market ensures that technical innovations are reflected in the improvements of our products. Based on the technical parame-
ters listed below and the ambience you want our product to operate in, we here at ebm-papst can always work out the best solution for your specific
application..
Technical parameters & scope
173
Standards
Information on standards is provided in the product-specific data sheets.
EMC
Information on EMC standards is provided in the product-specific data
sheets.
Complying with the EMC standards has to be established on the final
appliance, as different mounting situations can result in changed EMC
properties.
Leakage current
Information on the leakage current is provided in the product-specific
data sheets.
Measuring is according to IEC 60990.
Approvals
In case you require a specific approval for your ebm-papst product
(VDE, UL, GOST, CCC, CSA, etc.) please let us know.
Most of our products can be supplied with the relevant approval.
Information on existing approvals is provided in the product-specific
data sheets.
Air performance measurements
All air performance measurements are carried out on suction side and on
chamber test beds conforming to the specifications as per ISO 5801 and
DIN 24163. The fans under test are installed in the measuring chamber at
free air intake and exhaust (installation category A) and are operated at
nominal voltage, with AC also at nominal frequency, and without any
additional components such as guard grilles.
As required by the standard, the air performance curves correspond to
an air density of 1.2 kg/m3.
Vibration test
Vibration tests are carried out in compliance with
Vibration test in operation according to DIN IEC 68, parts 2-6
Vibration test at standstill according to DIN IEC 68, parts 2-6
Shock load
Shock load tests are carried out in compliance with
Shock load according to DIN IEC 68, parts 2-27
Balancing quality
Testing the balancing quality is carried out in compliance with
Residual imbalance according to DIN ISO 1940
Standard balancing quality level G 6.3
Should you require a higher balancing quality level for your specific
application, please let us know and specify this when ordering your
product.
Chemo-physical strain / performance parameters
Should you have questions about chemo-physical strain, please direct
them to your ebm-papst contact.
Fields of application, industries and applications
Our products are used in various industries and applications:
Ventilation, air-conditioning and refrigeration technology, clean room
technology, automotive and rail technology, medical and laboratory tech -
nology, electronics, computer and office technology, telecommunications,
household appliances, heating, machines and plants, drive engineering.
Our products are not designed for use in the aviation and aerospace
industry!
Legal and normative directives
The products described in this catalogue are designed, developed and
produced in keeping with the standards in place for the relevant product
and, if known, the conditions governing the relevant fields of application.
174
Sound pressure level and sound level
All acoustic values are established according to ISO 13347, DIN 45635
and ISO 3744/3745 to accuracy class 2 and given in A-rated form.
When the sound pressure level (Lp) is measured, the microphone is on
the intake side of the fan being tested, usually at a distance of 1 m on
the fan axis.
To measure the sound power level (Lw), 10 microphones are distributed
over an enveloping surface on the intake side of the fan being tested
(see graphic). The sound power level measured can be roughly calculated
from the sound pressure level by adding 7 dB.
Measuring configuration as per ISO 13347-3 respectively DIN 45635-38:
10 measuring points
d D
h = 1,5d ... 4,5d
Measurement area S = 6d2+ 7d (h + 1,5d)
3d
2d
h
D
1,5d
Measurement conditions for air and noise measurement
ebm-papst products are measured under the following conditions:
Axial and diagonal fans in direction of rotation “V” in full nozzle and
without guard grille
Backward curved centrifugal fans, free-running and with inlet nozzle
Forward curved single and dual inlet centrifugal fans with housing
Noise measurements
All noise measurements are carried out in low-reflective test rooms with
reverberant floor. Thus the ebm-papst acoustic test chambers meet the
requirements of precision class 1 according to DIN EN ISO 3745. For noise
measurement, the fans being tested are placed in a reverberant wall and
operated at nominal voltage (for AC, also at nominal frequency) without
additional attachments such as the guard grille.
Technical parameters & scope
175
15
10 15 20 255 82 3
10590
1
Number of sources of sound with identical level
Increase in sound pressure / sound power level
4 6 7 9
[dB]
[dB(A)]
3
12 16 20 2484
21 1,50
0
Difference in level with two sources of sound
Increase in sound pressure / sound power level [dB]
[dB(A)]
[dB]
[dB(A)]
0
10 20 50 10052
-10-26 -20-30-40
1
[m]
Distance
Decrease in sound pressure level [dB]
[dB(A)]
Combined level of multiple same-level sound sources
Adding 2 noise sources with the same level results in a level increase of approx. 3 dB.
The noise characteristics of multiple identical fans can be determined in advance based on
the noise values specified in the data sheet. This is shown in the diagram opposite.
Example: 8 A3G800 axial fans are on a condenser. According to the data sheet, the sound pres-
sure level of a fan is approximately 75 dB(A). The level increase measured from the diagram is
9 dB. Thus the overall sound level of the installation can be expected to be 84 dB(A).
Combined level of two different-level sound sources
The acoustic performance of two different fans can be predetermined based on the sound
levels given in the data sheet. This is shown in the diagram opposite.
Example: There is an axial fan A3G800 with a sound pressure level of 75 dB(A) at the operating
point and an axial fan A3G710 with 71 dB(A) in a ventilation unit. The level difference is 4 dB.
The level increase can now be read in the diagram as approx. 1.5 dB. This means that the
overall sound level of the unit can be expected to be 76.5 dB(A).
Distance laws
Sound power level is independent of distance to the sound source. In contrast to this, sound
pressure level decreases the further away the noise source is. The adjacent diagram shows the
decrease in level under far sound field conditions. Far sound field conditions apply whenever the
distance between microphone and fan is big when compared to fan diameter and wavelength to
be considered. For more information on far sound field, please consult the relevant literature on
this complex topic. Per doubling of distance, the level in the far sound field decreases by 6 dB.
In the near field of the fan, other correlations apply and the decrease in levels can be consider-
ably smaller. The following example only applies to far sound field conditions and can vary
strongly depending on the installation effects:
With an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of
1 m. According to the adjacent diagram, at a distance of 20 m we would get a reduction by
26 dB, i.e. a sound pressure level of 39 dB(A).
176 motor specialist
Heilbronn / Heidelberg
Dipl.-Ing. Mark Gartner
Gehrweg 12
74199 Unterheinriet
GERMANY
Phone +49 7130 404569-1
Fax +49 7130 404569-2
Mark.Gartner@de.ebmpapst.com
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
35075 Gladenbach
GERMANY
Phone +49 6462 4071-10
Fax +49 6462 4071-11
Ralph.Brueck@de.ebmpapst.com
Koblenz
Winfried Schaefer
Hinter der Kirch 10
56767 Uersfeld
GERMANY
Phone +49 2657 16-96
Fax +49 2657 16-76
Winfried.Schaefer@de.ebmpapst.com
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Landsbergerstraße 14
86932 Pürgen
GERMANY
Phone +49 8196 99877-54
Fax +49 8196 99877-55
Jens.Peter@de.ebmpapst.com
Nuremberg
Dipl.-Wirt.-Ing. (FH) Axel Resch
Dr.-August-Koch-Str. 1
91639 Wolframs-Eschenbach
GERMANY
Phone +49 9875 9783-170
Fax +49 9875 9783-171
Axel.Resch@de.ebmpapst.com
Offenburg
Dipl.-Ing. (FH) Ralf Braun
Hubeneck 21
77704 Oberkirch
GERMANY
Phone +49 7802 9822-52
Fax +49 7802 9822-53
Ralf.Braun@de.ebmpapst.com
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
73207 Plochingen
GERMANY
Phone +49 7153 9289-80
Fax +49 7153 9289-81
Rudi.Weinmann@de.ebmpapst.com
Ulm
M.Sc. Reinhard Sommerreißer
Am Silbermannpark 10
86161 Augsburg
GERMANY
Phone +49 821 6610-7023
Fax +49 821 6610-7024
Reinhard.Sommerreisser@de.ebmpapst.com
Distributoren
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
63110 Rodgau - Jügesheim
GERMANY
Phone +49 6106 841-0
Fax +49 6106 841-111
info@red-elektromechanik.de
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
info@breuell-hilgenfeldt.de
Munich
A. Schweiger GmbH
Ohmstraße 1
82054 Sauerlach
GERMANY
Phone +49 8104 897-0
Fax +49 8104 897-90
info@schweiger-gmbh.de
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
ebmpapst@breuell-hilgenfeldt.de
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
74677 Dörzbach
GERMANY
Phone +49 7937 80355-20
Fax +49 7937 80355-25
info@hds-gmbh.net
www.hds-gmbh.net
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
16341 Panketal
GERMANY
Phone +49 30 944149-62
Fax +49 30 944149-63
Jens.Duchow@de.ebmpapst.com
Bielefeld
Dipl.-Ing. (FH) Wolf-Jürgen Weber
Niehausweg 13
33739 Bielefeld
GERMANY
Phone +49 5206 91732-31
Fax +49 5206 91732-35
Wolf-Juergen.Weber@de.ebmpapst.com
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
59519 Möhnesee-Völlinghausen
GERMANY
Phone +49 2925 800-407
Fax +49 2925 800-408
Hans-Joachim.Pundt@de.ebmpapst.com
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr.-Hermann-Krause-Straße 23
63452 Hanau
GERMANY
Phone +49 6181 1898-12
Fax +49 6181 1898-13
Christian.Kleffmann@de.ebmpapst.com
Halle
Dipl.-Ing. (TU) Michael Hanning
Lercheneck 4
06198 Salzatal / OT Lieskau
GERMANY
Phone +49 345 55124-56
Fax +49 345 55124-57
Michael.Hanning@de.ebmpapst.com
Hamburg
Ingenieurbüro Breuell GmbH
Ing. Dirk Kahl
Elektroingenieur
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-19
Fax +49 40 538092-84
Dirk.Kahl@de.ebmpapst.com
ebm-papst in Germany
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
GERMANY
Phone +49 7938 81-0
Fax +49 7938 81-110
info1@de.ebmpapst.com
ebm-papst St. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
78112 St. Georgen
GERMANY
Phone +49 7724 81-0
Fax +49 7724 81-1309
info2@de.ebmpapst.com
ebm-papst Landshut GmbH
Hofmark-Aich-Straße 25
84030 Landshut
GERMANY
Phone +49 871 707-0
Fax +49 871 707-465
info3@de.ebmpapst.com
compact fan agent motor agentfan agent
177
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Straubingstraße 17
4030 Linz
AUSTRIA
Phone +43 732 321150-0
Fax +43 732 321150-20
info@at.ebmpapst.com
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
P.O. Box 117
220138 Minsk
BELARUS
Phone +375 17 3851556
Fax +375 17 3851556
info@by.ebmpapst.com
www.ebmpapst.by
Belgium
ebm-papst Benelux B.V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
3001 Heverlee-Leuven
BELGIUM
Phone +32 16 396-200
Fax +32 16 396-220
info@be.ebmpapst.com
www.ebmpapst.be
Bulgaria
ebm-papst Romania S.R.L.
Str. Tarnavei No. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
dudasludovic@xnet.ro
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
office@hu.ebmpapst.com
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Kaštanová 34a
620 00 Brno
CZECH REPUBLIC
Phone +420 544 502-411
Fax +420 547 232-622
info@ebmpapst.cz
www.ebmpapst.cz
Denmark
ebm-papst Denmark ApS
Vallensbækvej 21
2605 Brøndby
DENMARK
Phone +45 43 631111
Fax +45 43 630505
mail@dk.ebmpapst.com
www.ebmpapst.dk
Estonia
ebm-papst Oy, Eesti Filiaal
Kesk tee 13
Aaviku küla, Jüri Tehnopark
75301 Rae Vald, Harjumaa
ESTONIA
Phone +372 65569-78
Fax +372 65569-79
www.ebmpapst.ee
Finland
ebm-papst Oy
Puistotie 1
02760 Espoo
FINLAND
Phone +358 9 887022-0
Fax +358 9 887022-13
mailbox@ebmpapst.fi
www.ebmpapst.fi
France
ebm-papst sarl
ZI Nord - rue A. Mohler
BP 62
67212 Obernai Cedex
FRANCE
Phone +33 820 326266
Fax +33 3 88673883
info@ebmpapst.fr
www.ebmpapst.fr
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
17672 Kallithea-Attiki
GREECE
Phone +30 210 9513-705
Fax +30 210 9513-490
contact@helcoma.gr
www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
office@hu.ebmpapst.com
Iceland
RJ Engineers
Stangarhyl 1a
110 Reykjavik
ICELAND
Phone +354 567 8030
Fax +354 567 8015
rj@rj.is
www.rj.is
Ireland
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
sales@uk.ebmpapst.com
www.ebmpapst.co.uk
AuBren Limited
Portlaoise Business & Technology Park
Mountrath Road
Portlaoise, Co. Laois
IRELAND
Phone +353 57 8664343
Fax +353 57 8664346
sales@ie.aubren.com
www.aubren.com
Italy
ebm-papst Srl
Via Cornaggia 108
22076 Mozzate (Co)
ITALY
Phone +39 0331 836201
Fax +39 0331 821510
info@it.ebmpapst.com
www.ebmpapst.it
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
office@hu.ebmpapst.com
ebm-papst in Europe
178
Russia
ebm-papst Ural GmbH
Posadskaja-Strasse, 23(E), 3
620102 Ekaterinburg
RUSSIA
Phone +7 343 2338000
Fax +7 343 2337788
Konstantin.Molokov@ru.ebmpapst.com
www.ebmpapst.ur.ru
ebm-papst Rus GmbH
proezd 4529, vladenie 5, stroenie 1
141000 Mytistschi, Oblast Moskau
RUSSIA
Phone +7 495 9807524
Fax +7 495 5140924
info@ebmpapst.ru
www.ebmpapst.ru
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
office@hu.ebmpapst.com
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
28830 San Fernando de Henares (Madrid)
SPAIN
Phone +34 91 6780894
Fax +34 91 6781530
ventas@ebmpapst.es
www.ebmpapst.es
Sweden
ebm-papst AB
Äggelundavägen 2
17562 Järfälla
SWEDEN
Phone +46 10 4544400
Fax +46 8 362306
info@ebmpapst.se
www.ebmpapst.se
Switzerland
ebm-papst AG
Rütisbergstrasse 1
8156 Oberhasli
SWITZERLAND
Phone +41 44 73220-70
Fax +41 44 73220-77
verkauf@ebmpapst.ch
www.ebmpapst.ch
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
35620 Cigli-Izmir
TURKEY
Phone +90 232 3282090
Fax +90 232 3280270
akantel@akantel.com.tr
www.ebmpapst.com.tr
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 21
03067 Kiev
UKRAINE
Phone +38 044 2063091
Fax +38 044 2063091
mail@ebmpapst.ua
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
sales@uk.ebmpapst.com
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane
East Ilsley, Berkshire RG20 7LG
UNITED KINGDOM
Phone +44 1635 2811-11
Fax +44 1635 2811-61
A&Dsales@uk.ebmpapst.com
www.ebmpapst-ad.com
Netherlands
ebm-papst Benelux B.V.
Engelseweg 127
5705 AC Helmond
NETHERLANDS
Phone +31 492 502-900
Fax +31 492 502-950
verkoop@nl.ebmpapst.com
www.ebmpapst.nl
Norway
ebm-papst AS
P.B. 173 Holmlia
1203 Oslo
NORWAY
Phone +47 22 763340
Fax +47 22 619173
mailbox@ebmpapst.no
www.ebmpapst.no
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
03236 Warszawa
POLAND
Phone +48 22 6757819
Fax +48 22 6769587
office@ebmpapst.pl
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Centro Empresarial de Alverca
Rua de Adarse, Vale D’Ervas
Corpo D / Fracção 3
2615-178 Alverca do Ribatejo
PORTUGAL
Phone +351 218 394 880
Fax +351 218 394 759
info@pt.ebmpapst.com
www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tarnavei Nr. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
dudasludovic@xnet.ro
ebm-papst in Europe
motor specialistcompact fan agent motor agentfan agent
179
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
ARGENTINA
Phone +54 11 46576135
Fax +54 11 46572092
ventas@ar.ebmpapst.com
www.ebmpapst.com.ar
Brasil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
06707-100 Cotia - São Paulo
BRAZIL
Phone +55 11 4613-8700
Fax +55 11 4777-1456
vendas@br.ebmpapst.com
www.ebmpapst.com.br
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
Pickering, Ontario, L1W3J9
CANADA
Phone +1 905 420-3533
Fax +1 905 420-3772
sales@ca.ebmpapst.com
www.ebmpapst.ca
Mexico
ebm Industrial S. de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
Mexico 05120, D.F.
MEXICO
Phone +52 55 3300-5144
Fax +52 55 3300-5243
sales@mx.ebmpapst.com
www.ebmpapst.com.mx
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
Farmington, CT 06034
UNITED STATES
Phone +1 860 674-1515
Fax +1 860 674-8536
sales@us.ebmpapst.com
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfield, Suite 255
Dearborn, MI 48120
UNITED STATES
Phone +1 313 406-8080
Fax +1 313 406-8081
automotive@us.ebmpapst.com
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
2040 Honeydew
SOUTH AFRICA
Phone +27 11 794-3434
Fax +27 11 794-5020
info@za.ebmpapst.com
www.ebmpapst.co.za
ebm-papst in America and Africa
180
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
200131 Shanghai
P.R. of CHINA
Phone +86 21 5046-0183
Fax +86 21 5046-1119
sales@cn.ebmpapst.com
www.ebmpapst.com.cn
Hong Kong
ebm-papst Hong Kong Ltd.
Room 17E, MG Tower
133 Hoi Bun Road, Kwun Tong
Hong Kong
P.R. of CHINA
Phone +852 2145-8678
Fax +852 2145-7678
info@hk.ebmpapst.com
India
ebm-papst India Pvt. Ltd.
26/3, G.N.T. Road, Erukkencherry
Chennai-600118
INDIA
Phone +91 44 25372556
Fax +91 44 25371149
sales@in.ebmpapst.com
www.ebmpapst.in
Indonesia
ebm-papst Indonesia
Representative Office
German Centre, 4th Floor, Suite 4470
Jl. Kapt. Subijono Dj. Bumi Serpong Damai
15321 Tangerang
INDONESIA
Phone +62 21 5376250
Fax +62 21 5388305
salesdept@id.ebmpapst.com
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
Kiryat Arie, Petach-Tikva 49514
ISRAEL
Phone +972 3 9100300
Fax +972 3 5796679
polak@polak.co.il
www.polak.co.il
Japan
ebm-papst Industries Japan K.K.
12th Floor, Benex S-3 Bldg.
3-20-8 Shinyokohama, Kohoku-ku
222-0033 Yokohama
JAPAN
Phone +81 45 47057-51
Fax +81 45 47057-52
info@jp.ebmpapst.com
www.ebmpapst.jp
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
B 6-2, Digital Media City (DMC)
Sangam-Dong, Mapo-Gu
Seoul 121-270
KOREA
Phone +82 2 366213-24
Fax +82 2 366213-26
info@kr.ebmpapst.com
www.ebmpapst.co.kr
Malaysia
ebm-papst Malaysia
Representative Office
Unit 12-2, Jalan USJ Sentral 3
Persiaran Subang, Selangor Darul Ehsan
47600 Subang Jaya
MALAYSIA
Phone +60 3 8024-1680
Fax +60 3 8024-8718
salesdept@my.ebmpapst.com
Singapore
ebm-papst SEA Pte. Ltd.
No. 23 Ubi Road 4
#06-00 Olympia Industrial Building
Singapore 408620
SINGAPORE
Phone +65 65513789
Fax +65 68428439
salesdept@sg.ebmpapst.com
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
Tsow-Inn District, Kaohsiung
TAIWAN
Phone +886 7 557-4268
Fax +886 7 557-2788
eteco@ms22.hinet.net
www.ebmpapst.com.tw
Thailand
ebm-papst Thailand Co., Ltd.
99/9 Moo 2, Central Chaengwattana Tower
14th Floor, Room 1402
Chaengwattana Road Bangtarad, Pakkret
11120 Nonthaburi
THAILAND
Phone +66 2 8353785-7
Fax +66 2 8353788
salesdept@th.ebmpapst.com
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
Dubai
UNITED ARAB EMIRATES
Phone +971 4 88608-26
Fax +971 4 88608-27
info@ae.ebmpapst.com
www.ebmpapst.ae
Vietnam
ebm-papst Vietnam
Representative Office
Room #102, 25 Nguyen Van Thu Street
District 1
Ho Chi Minh City
VIETNAM
Phone +84 8 39104099
Fax +84 8 39103970
linh.nguyen@vn.ebmpapst.com
Australia
Australia
ebm-papst A&NZ Pty Ltd.
10 Oxford Road
Laverton North, Victoria, 3026
AUSTRALIA
Phone +61 3 9360-6400
Fax +61 3 9360-6464
sales@ebmpapst.com.au
www.ebmpapst.com.au
New Zealand
ebm-papst A&NZ Pty Ltd.
102 Henderson Valley Road
Henderson, Auckland 1230
NEW ZEALAND
Phone +64 9 837-1884
Fax +64 9 837-1899
sales@ebmpapst.com.au
www.ebmpapst.com.au
ebm-papst in Asia and Australia
motor specialistcompact fan agent motor agentfan agent
181
182
Notes
183
The engineer’s choice
www.ebmpapst.com
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
Germany
Phone +49 7938 81-0
Fax +49 7938 81-110
info1@de.ebmpapst.com
37850-7-8811 · 2013-05 · KD-3’
Printed in Germany