COMPUTING MVME2502 Data Sheet 1.0 GHz or 1.2 GHz Freescale QorIQTM P2020 processor based 6U VME board 2GB ECC DDR3-800 soldered down, support 4GB or 8 GB configurations Dual PMC/XMC sites 8GB eMMC solid state storage 512KB MRAM non-volatile data storage Three RJ-45 Gigabit Ethernet interfaces Five serial ports One USB 2.0 interface Optional rear transition module Hard drive mounting kit available Optional conformal coating Extended temperature (-40 C to +71 C) and rugged variants Freescale QorIQ P2020 VME64x SBC The Artesyn Embedded Technologies MVME2502 is a VME form factor single-board computer based on the very popular Freescale QorIQ P2020 dual core processor which features e500 cores delivering an excellent performance-to-power ratio. Compared to the other MVME2500 variants in the series, MVME2502 offers dual PMC/XMC sites whereas MVME2500 provides a single site solution. In addition it offers a range of front panel I/O including serial, USB 2.0, and Gigabit Ethernet plus a rear transition module with two Gigabit Ethernet, four RS-232 serial and a PMC Interface Module site. The MVME2502 comes standard with 2GB of soldered down DDR3-800 ECC DRAM, 8GB eMMC module and has a SATA connector for an optional 2.5" SATA SSD/HDD. Other features include dual flash banks, 3 independent tick timers, and on board 512K MRAM. MVME2502 is designed to work in legacy VMEbus chassis with a 3-row backplane connector environment with a reduced I/O capacity and reduced peripheral power budget. It is also designed to work in a more modern and higher performance VME chassis environment with a five-row backplane connector in the 2eVME or the 2eSST protocol mode. With such a wide range of I/O options, MVME2502 is designed for applications such as industrial control, semiconductor process equipment, radar, sonar and transportation signalling. It is available in commercial and rugged, extended temperature options which make it suitable for a wider range of environments. MVME2502 Data Sheet MVME2502 Block Diagram GbE RJ-45 COM Micro-DB9 USB USB 2.0 GbE MUX 2GB or 8GB DDR3 SDRAM SPD Real Time Clock 8 KB VPD EEPROM Temp Sensor (2) 64 KB User EEPROM DDR3-800 I2C XCVR RCMI RCMI XMC/PMC 2 Front I/O RS-232 XCVR Dual PHY eTSEC 2 XMC/PMC 1 Front I/O RS-232 GbE RJ-45 eTSEC 1 USB DUART Freescale QorIQ P2020 x1 PCIe MMC eSDHC SATA x1 PCIe PCIe to PCI-X Bridge PCI-X 64/133 CPLD Timers/ Regs RS-232 XCVR 10/100/1000Base-T I2C Local Bus LED6/ RST RCMI PHY Quad UART PCIe MUX/ DeMUX PCIe to PCI-X Bridge PCI-X x2 PCIe PCIe to PCI-X Bridge PMC 2 Connector XMC 1 Connector x1 PCIe 512 KB MRAM SATA Connector XMC 2 Connector x2 PCIe x2 PCIe PCIe SATA Controller SATA Controller (2) 8MB Flash PCIe PCIe PCIe MUX/ DeMUX x1 PCIe SPI SPI eLBC x1 PCIe I2C I2C eTSEC 3 8GB eMMC DDR Controller PCI-X 64/133 PMC 1 Connectors I/O to P2 64/133 PCIe-X to VME Bridge XCVR RS-232 VMEbus P2 P1 Transition Modules Software Support The MVME7216E transition module provides industry standard connector access to two 10/100/1000BaseTX ports, and four asynchronous serial ports configured as RS-232 DTE. All of these are via RJ-45 connectors. The MVME7216E RTM is designed to directly connect to the VME backplane in chassis with an 80 mm deep rear transition area. This transition module is compatible with the MVME3100, MVME4100 and MVME7100 boards. FIRMWARE MONITOR The MVME2502 uses U-Boot firmware which is resident in the MVME2502 flash and provides power-on self-test, initialization and operating system booting capabilities. It is based on the 2013.01 patched U-Boot provided by Freescale. OPERATING SYSTEMS AND KERNELS The MVME2502 supports a variety of operating systems with associated Board Support Packages (BSPs): Fedora 13 Linux (2.6.27 kernel), VxWorks (6.9 SMP) and Linux kernels from Green Hills and LynuxWorks (upon customer request). MVME2502 Data Sheet Specifications OTHER FEATURES HARDWARE PROCESSOR/CHIPSET Watchdog unit 1.2 GHz Freescale P2020 dual-core processor (ENP1 variants) Three independent 32-bit tick timers 1.0 GHz Freescale P2020 dual-core processor (ENP2 variants) Status and user LEDs 512 KB L2 shared cache Reset switch Integrated, on-chip controllers for DDR2/3, PCI Express, USB 2.0, DUART, 10/100/1000 Ethernet, DMA, SDHC, SPI flash and I2C Locking ejector handles Eight 32-bit timers POWER REQUIREMENTS MEMORY Single channel, dual banks 800MB/s 2GB ECC DDR3-800, soldered down, standard Designed to support 4GB or 8GB configurations Temperature sensors Maximum for 1.2 GHz ENP1 variant * 5.0V 5.7A 28W (Estimated) Maximum for 1.0 GHz ENP2 variant TBD ENVIRONMENTAL Ruggedization Level ENP1 ENP2 Cooling Method Forced Air Forced Air Operating Temperature 0 C to +55 C -40 C to +71 C Storage Temperature -40 C to +85 C -50 C to +100 C Vibration Sine (10min/axis) 1G, 5 to 200 Hz 5G, 15 to 2000 Hz Support for crisis recovery Vibration Random (1hr/axis) .01 g2/Hz, 15 to 200 Hz .04 g2/Hz, 15 to 2000 Hz (8 GRMS) VMEBUS INTERFACE Shock 20 g/11 mS 30g/11 mS Compliance: ANSI/VITA 1-1994 VME64 (IEEE STD1014), ANSI/ VITA 1.1-1997 VME64 Extensions, VITA 1.5-199x 2eSST Humidity to 95% RH to 100% RH Conformal Coating* No Option (Acrylic) USER FLASH/NVRAM MEMORY 512 KB MRAM (NVRAM) 8GB Embedded MMC module (eMMC) BOOT FLASH MEMORY 16MB SPI flash (2x 8MB) Controller: Tundra Tsi148 PCI-X to VMEbus bridge with support for VME64 and 2eSST protocols * Conformal coating these products may result in up to a 2 C reduction in operating temperature limits. I/O CAPABILITIES ELECTROMAGNETIC COMPATIBILITY (EMC) Three RJ-45 Gigabit Ethernet interfaces (one front, one rear, one configurable to front or rear) Intended for use in systems meeting the following regulations: Two PMC/XMC with autosense One Micro DB-9 RS232 COM port (front) Four RJ-45 RS-232 serial ports (rear) One Type A USB 2.0 interface (front) SATA port optional on-board hard drive (in place of PMC2/ XMC2) * U.S.: FCC Part 15, Subpart B, Class A (non-residential) * Canada: ICES-003, Class A (non-residential) Artesyn board products are tested in a representative system to the following standards: * CE Mark per European EMC Directive 89/336/EEC with Amendments; Emissions: EN55022 Class B; Immunity: EN55024 * KCC Mark MVME721 TRANSITION MODULE I/O DOCUMENTATION Two GbE interfaces Installation Guide and Technical Reference Manual Four RS-232 serial ports Hardware Release Notes PMC I/O from PMC1 U-Boot Release Notes SOFTWARE Linux Installation and Programmer's Guides U-Boot Firmware ESTIMATED MTBF Predicted MTBF using Telcordia SR-332, issue 2 is between 600,000 and 700,000 hours, depending on memory configuration. VxWorks 6.8 BSP MVME2502 Data Sheet Ordering Information Part Number Description Weight MVME2502-02120201E MVME2502, P2020 at 1.2 GHz, 2GB DDR3-800, 8GB eMMC, ENP1, IEEE handles 0.70 kg MVME2502-02120201S MVME2502, P2020 at 1.2 GHz, 2GB DDR3-800, 8GB eMMC, ENP1, SCANBE handles - MVME2502-02100202E MVME2502, P2020 at 1.0 GHz, 2GB DDR3-800, 8GB eMMC, ENP2, IEEE handles 0.70 kg MVME2502-02100202S MVME2502, P2020 at 1.0 GHz, 2GB DDR3-800, 8GB eMMC, ENP2, SCANBE handles - REAR TRANSITION MODULES MVME7216E-101 MVME RTM, NEW I/O ON 5 ROW P2, 2 GIGE, 4 SERIAL, PIM, 6E (FOR USE WITH MVME3100/7100/4100/250x) MVME721ET-101 RTM, NEW I/O ON 5 ROW P2, 2 GIGE, 4 SERIAL, PIM, 6E ENP2 (FOR USE WITH MVME3100/4100/7100/250x) MVME721ET-102 RTM SCANBE, I/O ON 5 ROW P2, 2 GIGE, 4 SERIAL, PIM, 6E ENP2 (FOR USE WITH MVME3100/4100/7100/250x) ACCESSORIES AND CABLES SERIAL-MINI-D2 SERIAL CABLE - MICRO D SUB CONNECTOR TO STANDARD DB9 ACC/CABLE/SER/DTE/6E SERIAL CABLE, RD 009, 2M, 2 DTE MD/D, RJ-45 TO DB9 MVME2502-HDMNTKIT1 MVME2502 HD MOUNTING KIT MVME2501-HDMNTKIT2 MVME2502 HD MOUNTING KIT ENP2 SOLUTION SERVICES Artesyn Embedded Technologies provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. PICMG, AdvancedTCA, ATCA and the AdvancedTCA logo are trademarks of PICMG. Service Availability is a proprietary trademark used under license. Intel and Xeon are trademarks of Intel Corporation or its subsidiaries in the Unites States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other product or service names are the property of their respective owners. This document identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Artesyn Embedded Technologies may sell products. A prospective buyer should exercise its own independent judgment to confirm the suitability of the products for particular applications. Artesyn reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Artesyn does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Artesyn's licensee, licensee's transferees, and licensee's customers and users. Availability of some of the products and services described herein may be restricted in some locations. WORLDWIDE OFFICES Tempe, AZ U.S.A. +1 888 412 7832 Munich, Germany +49 89 9608 2552 Hong Kong +852 2176 3540 Shanghai, China +86 21 3395 0289 Tokyo, Japan +81 3 5403 2730 Seoul, Korea +82 2 3483 1500 www.artesyn.com Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. (c) 2015 Artesyn Embedded Technologies, Inc MVME2502 22Jun2015