COMPUTING
1.0 GHz or 1.2 GHz Freescale QorIQ™
P2020 processor based 6U VME
board
2GB ECC DDR3-800 soldered down,
support 4GB or 8 GB congurations
Dual PMC/XMC sites
8GB eMMC solid state storage
512KB MRAM non-volatile data
storage
Three RJ-45 Gigabit Ethernet
interfaces
Five serial ports
One USB 2.0 interface
Optional rear transition module
Hard drive mounting kit available
Optional conformal coating
Extended temperature (-40 °C to
+71 °C) and rugged variants
MVME2502
Freescale QorIQ P2020 VME64x SBC
The Artesyn Embedded Technologies MVME2502 is a VME form factor single-board computer
based on the very popular Freescale QorIQ P2020 dual core processor which features e500
cores delivering an excellent performance-to-power ratio. Compared to the other MVME2500
variants in the series, MVME2502 offers dual PMC/XMC sites whereas MVME2500 provides a
single site solution. In addition it offers a range of front panel I/O including serial, USB 2.0, and
Gigabit Ethernet plus a rear transition module with two Gigabit Ethernet, four RS-232 serial and
a PMC Interface Module site. The MVME2502 comes standard with 2GB of soldered down
DDR3-800 ECC DRAM, 8GB eMMC module and has a SATA connector for an optional 2.5”
SATA SSD/HDD. Other features include dual ash banks, 3 independent tick timers, and on
board 512K MRAM.
MVME2502 is designed to work in legacy VMEbus chassis with a 3-row backplane connector
environment with a reduced I/O capacity and reduced peripheral power budget. It is also
designed to work in a more modern and higher performance VME chassis environment with a
ve-row backplane connector in the 2eVME or the 2eSST protocol mode.
With such a wide range of I/O options, MVME2502 is designed for applications such as
industrial control, semiconductor process equipment, radar, sonar and transportation signalling.
It is available in commercial and rugged, extended temperature options which make it suitable
for a wider range of environments.
Data Sheet
MVME2502 Data Sheet
Freescale QorIQ
P2020
P1P2
RS-232
XCVR
XMC/PMC 1
Front I/O
GbE
RJ-45 USB
GbE
RJ-45
COM
Micro-DB9
eTSEC 1
eTSEC 2
GbE
MUX
Dual PHY
10/100/1000Base-T
PHY
USB DUART DDR
Controller
I2C
eSDHC
SPI
PCIe
PCIe
PCIe
eLBC
eTSEC 3
RCMI
RCMI
RCMI
USB 2.0
RS-232
XCVR
CPLD
Timers/
Regs
LED6/
RST
Local Bus
Quad
UART
RS-232
XCVR
RS-232
512 KB
MRAM
PCIe to
PCI-X
Bridge
PCI-X 64/133
XCVR
VMEbus
x1 PCIe
I2C
I/O to P2
PMC 1
Connectors
PCI-X
64/133
PCIe to
PCI-X
Bridge
PCIe
MUX/
DeMUX
x2 PCIe
8GB
eMMC
x2 PCIe
SPI
MMC
I2C
DDR3-800
XMC 1
Connector
x2 PCIe
SATA
Connector
SATA
Controller
x1 PCIe
SPD
2GB or 8GB
DDR3 SDRAM
I2C
Real
Time
Clock
Temp
Sensor
8 KB
VPD
EEPROM
(2) 64 KB
User
EEPROM
XMC/PMC 2
Front I/O
Flash
(2) 8MB
SATA
Controller
x1 PCIe SATA
x1 PCIe
x1 PCIe PCI-X
PCIe to PCI-X
Bridge
PCIe
MUX/
DeMUX
PCIe-X to
VME
Bridge
XMC 2
PMC 2
Connector
Connector
64/133
MVME2502 Block Diagram
Transition Modules
The MVME7216E transition module provides industry standard
connector access to two 10/100/1000BaseTX ports, and four
asynchronous serial ports congured as RS-232 DTE. All of these
are via RJ-45 connectors. The MVME7216E RTM is designed to
directly connect to the VME backplane in chassis with an 80 mm
deep rear transition area. This transition module is compatible
with the MVME3100, MVME4100 and MVME7100 boards.
Software Support
FIRMWARE MONITOR
The MVME2502 uses U-Boot rmware which is resident in the
MVME2502 ash and provides power-on self-test, initialization
and operating system booting capabilities. It is based on the
2013.01 patched U-Boot provided by Freescale.
OPERATING SYSTEMS AND KERNELS
The MVME2502 supports a variety of operating systems with
associated Board Support Packages (BSPs): Fedora 13 Linux
(2.6.27 kernel), VxWorks (6.9 SMP) and Linux kernels from Green
Hills and LynuxWorks (upon customer request).
MVME2502 Data Sheet
Specications
HARDWARE PROCESSOR/CHIPSET
1.2 GHz Freescale P2020 dual-core processor (ENP1 variants)
1.0 GHz Freescale P2020 dual-core processor (ENP2 variants)
512 KB L2 shared cache
Integrated, on-chip controllers for DDR2/3, PCI Express,
USB 2.0, DUART, 10/100/1000 Ethernet, DMA, SDHC,
SPI ash and I2C
Eight 32-bit timers
MEMORY
Single channel, dual banks 800MB/s
2GB ECC DDR3-800, soldered down, standard
Designed to support 4GB or 8GB congurations
USER FLASH/NVRAM MEMORY
512 KB MRAM (NVRAM)
8GB Embedded MMC module (eMMC)
BOOT FLASH MEMORY
16MB SPI ash (2x 8MB)
Support for crisis recovery
VMEBUS INTERFACE
Compliance: ANSI/VITA 1-1994 VME64 (IEEE STD1014), ANSI/
VITA 1.1-1997 VME64 Extensions, VITA 1.5-199x 2eSST
Controller: Tundra Tsi148 PCI-X to VMEbus bridge with support
for VME64 and 2eSST protocols
I/O CAPABILITIES
Three RJ-45 Gigabit Ethernet interfaces (one front, one rear, one
congurable to front or rear)
Two PMC/XMC with autosense
One Micro DB-9 RS232 COM port (front)
Four RJ-45 RS-232 serial ports (rear)
One Type A USB 2.0 interface (front)
SATA port optional on-board hard drive (in place of PMC2/
XMC2)
MVME721 TRANSITION MODULE I/O
Two GbE interfaces
Four RS-232 serial ports
PMC I/O from PMC1
SOFTWARE
U-Boot Firmware
VxWorks 6.8 BSP
OTHER FEATURES
Watchdog unit
Three independent 32-bit tick timers
Status and user LEDs
Reset switch
Locking ejector handles
Temperature sensors
POWER REQUIREMENTS
Maximum for 1.2 GHz ENP1 variant
• 5.0V 5.7A 28W (Estimated)
Maximum for 1.0 GHz ENP2 variant TBD
ENVIRONMENTAL
Ruggedization Level ENP1 ENP2
Cooling Method Forced Air Forced Air
Operating Temperature 0 °C to +55 °C –40 °C to +71 °C
Storage Temperature –40 °C to +85 °C –50 °C to +100 °C
Vibration Sine
(10min/axis)
1G, 5 to 200 Hz 5G, 15 to 2000 Hz
Vibration Random
(1hr/axis)
.01 g2/Hz,
15 to 200 Hz
.04 g2/Hz, 15 to
2000 Hz (8 GRMS)
Shock 20 g/11 mS 30g/11 mS
Humidity to 95% RH to 100% RH
Conformal Coating* No Option (Acrylic)
* Conformal coating these products may result in up to a 2 °C reduction in operating temperature limits.
ELECTROMAGNETIC COMPATIBILITY (EMC)
Intended for use in systems meeting the following regulations:
• U.S.: FCC Part 15, Subpart B, Class A (non-residential)
• Canada: ICES-003, Class A (non-residential)
Artesyn board products are tested in a representative system to
the following standards:
• CE Mark per European EMC Directive 89/336/EEC with
Amendments; Emissions: EN55022 Class B; Immunity:
EN55024
• KCC Mark
DOCUMENTATION
Installation Guide and Technical Reference Manual
Hardware Release Notes
U-Boot Release Notes
Linux Installation and Programmer’s Guides
ESTIMATED MTBF
Predicted MTBF using Telcordia SR-332, issue 2 is between
600,000 and 700,000 hours, depending on memory conguration.
MVME2502 Data Sheet
www.artesyn.com
WORLDWIDE OFFICES
Tempe, AZ U.S.A. +1 888 412 7832 Shanghai, China +86 21 3395 0289
Munich, Germany +49 89 9608 2552 Tokyo, Japan +81 3 5403 2730
Hong Kong +852 2176 3540 Seoul, Korea +82 2 3483 1500
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc
PICMG, AdvancedTCA, ATCA and the AdvancedTCA logo are trademarks of PICMG. Service Availability is a proprietary trademark used under license. Intel and Xeon are trademarks of Intel Corporation
or its subsidiaries in the Unites States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other product or service names are the property of their
respective owners.
This document identies products, their specications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future
availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Artesyn Embedded Technologies may sell products. A prospective buyer
should exercise its own independent judgment to conrm the suitability of the products for particular applications. Artesyn reserves the right to make changes, without notice, to any products or information
herein which will, in its sole discretion, improve reliability, function, or design. Artesyn does not assume any liability arising out of the application or use of any product or circuit described herein; neither
does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Artesyn’s licensee, licensee’s transferees,
and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations.
SOLUTION SERVICES
Artesyn Embedded Technologies provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help
speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh.
Ordering Information
Part Number Description Weight
MVME2502-02120201E MVME2502, P2020 at 1.2 GHz, 2GB DDR3-800, 8GB eMMC, ENP1, IEEE handles 0.70 kg
MVME2502-02120201S MVME2502, P2020 at 1.2 GHz, 2GB DDR3-800, 8GB eMMC, ENP1, SCANBE handles –
MVME2502-02100202E MVME2502, P2020 at 1.0 GHz, 2GB DDR3-800, 8GB eMMC, ENP2, IEEE handles 0.70 kg
MVME2502-02100202S MVME2502, P2020 at 1.0 GHz, 2GB DDR3-800, 8GB eMMC, ENP2, SCANBE handles –
REAR TRANSITION MODULES
MVME7216E-101 MVME RTM, NEW I/O ON 5 ROW P2, 2 GIGE, 4 SERIAL, PIM, 6E (FOR USE WITH MVME3100/7100/4100/250x)
MVME721ET-101 RTM, NEW I/O ON 5 ROW P2, 2 GIGE, 4 SERIAL, PIM, 6E ENP2 (FOR USE WITH MVME3100/4100/7100/250x)
MVME721ET-102 RTM SCANBE, I/O ON 5 ROW P2, 2 GIGE, 4 SERIAL, PIM, 6E ENP2 (FOR USE WITH MVME3100/4100/7100/250x)
ACCESSORIES AND CABLES
SERIAL-MINI-D2 SERIAL CABLE - MICRO D SUB CONNECTOR TO STANDARD DB9
ACC/CABLE/SER/DTE/6E SERIAL CABLE, RD 009, 2M, 2 DTE MD/D, RJ-45 TO DB9
MVME2502-HDMNTKIT1 MVME2502 HD MOUNTING KIT
MVME2501-HDMNTKIT2 MVME2502 HD MOUNTING KIT ENP2
MVME2502 22Jun2015
