AUO G057QN01 V0 G057QN01 V0 (V ) Preliminary Specification ( ) Final Specification Module 5.7 Inch Color TFT-LCD Model Name G057QN01 V0 Customer Date Checked & Approved by Approved by Prepared by David Hsing Note: This Specification is subject to change without notice. Date 2007/11/20 General Display Business Division / AU Optronics corporation G057QN01 V0 Ver. 0.2 1/20 G057QN01 V0 Contents 1. Operating Precautions .....................................................................................4 2. General Description..........................................................................................5 2.1 Display Characteristics.......................................................................................................5 2.2 Optical Characteristics .......................................................................................................6 3. Functional Block Diagram................................................................................8 4. Absolute Maximum Ratings .............................................................................9 4.1 Absolute Ratings of TFT-LCD Module................................................................................9 4.2 Absolute Ratings of Environment .......................................................................................9 5. Electrical Characteristics .................................................................................9 5.1 TFT-LCD Driving ................................................................................................................9 5.2 Backlight Unit Driving ....................................................................................................... 11 6. Signal Characteristic ......................................................................................11 6.1 Pixel Format Image .......................................................................................................... 11 6.2 Scanning Direction ...........................................................................................................12 6.3 The Input Data Format .....................................................................................................12 6.4 TFT- LCD Interface Signal Description.............................................................................13 6.5 TFT- LCD Interface Timing ...............................................................................................14 6.6 LED Backlight Unit Interface ............................................................................................15 6.7 Power ON/OFF Sequence ...............................................................................................15 7. Connector & Pin Assignment.........................................................................16 7.1 TFT- LCD Signal (CN1): LCD Connector .........................................................................16 7.2 LED Backlight Unit (CN2): LED Connector ......................................................................16 7.3 PIN 1 definition of CN1 and CN2 .....................................................................................17 8. Reliability Test Criteria ...................................................................................17 9. Mechanical Characteristics............................................................................19 10. Label and Packaging ....................................................................................20 10.1 Shipping Label (on the rear side of TFT-LCD display) ...................................................20 10.2 Carton Package .............................................................................................................20 11 Safety..............................................................................................................20 11.1 Sharp Edge Requirements .............................................................................................20 11.2 Materials .........................................................................................................................20 11.3 Capacitors ......................................................................................................................20 11.4 National Test Lab Requirement ......................................................................................20 G057QN01 V0 Ver. 0.2 2/20 G057QN01 V0 Record of Revision Version and Date Page Old description 0.1, Oct. 04, 2007 All 0.2, Nov.20, 2007 5 No description 11 No description 16 Pin 3: Hsync Pin 4: Vsync 19 New Description Remark First edition preliminary specifications Add "The most suitable view angle:12 o'clock" Add "VF typical specification" Add "Note 1" Pin 3: NC Pin 4: NC 2D drawing update Add" Suggested applying torque: 0.15~0.2 Nm" Section 2.1 Section 5.2.1 Section 7.1 Section 9 G057QN01 V0 Ver. 0.2 3/20 G057QN01 V0 1. Operating Precautions 1) Display area (Polarizer) of TFT-LCD Module is easily to be damaged, please be cautious and not to scratch it. 2) Be sure to power off your machine before connecting or disconnecting your signal cable to TFT-LCD Module. 3) Wipe off water drop on display area immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth. 5) Display area (Glass) of TFT-LCD Module may be broken or cracked if bump Module against hard object. 6) To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling TFT-LCD Module. 7) Do not open nor modify the TFT-LCD module assembly. 8) Do not press the reflector sheet at the back of the module to any direction. 9) In case if TFT-LCD module has to be put back into the packing container slot after it was taken out from the container, do not press the center of the LED Reflector edge. Instead, press at the far ends of the LED Reflector edge softly. Otherwise the TFT-LCD Module may be damaged. 10) When inserting or removing of your signal cable to TFT-LCD Module, be sure not to apply abnormal force (rotate, tilt...etc.) to the Connector of the TFT-LCD Module. 11) TFT-LCD Module is not allowed to be twisted & bent even force is added on module in a very short time. Please design your display product well to avoid external force applying to module by end-user directly. 12) Small amount of materials without flammability grade are used in the TFT-LCD module. The TFT-LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 13) Severe temperature condition may result in different luminance and short LED backlight opearting life time. 14) Continuous operating TFT-LCD Module under high temperature environment may accelerate LED light bar exhaustion and reduce luminance dramatically. 15) The data on this specification sheet is applicable when TFT-LCD module is placed in landscape position. 16) Continuous displaying fixed pattern may induce image sticking. It's recommended to use screen saver or moving content periodically if fixed pattern is displayed on the screen. G057QN01 V0 Ver. 0.2 4/20 G057QN01 V0 2. General Description G057QN01 V0 is designed for industrial display applications with QVGA (320 x RGB x 240) resolution and 262k colors (RGB 6-bits). It is composed of a TFT-LCD panel, driver ICs, control and power supply circuits board and backlight unit. G057QN01 V0 offers CMOS interface for display signal input. LED driving board for backlight unit is not included. 2.1 Display Characteristics The following items are G057QN01 V0 characteristics summary at 25 condition. Items Unit Specifications Screen Diagonal inch 5.7 Active Area mm 115.2(H) x 86.4(V) Pixels H x V Pixel Pitch 320 x 3(RGB) x 240 mm 0.36 x 0.36 Pixel Arrangement R.G.B. Vertical Stripe Display Mode TN, Normally White Nominal Input Voltage VDD Volt 3.3 typ. Typical Power Consumption Watt 2.19W (LCD:0.69W/LED: 1.5W) All black pattern Weight Grams 200g(typ.), 220g(max.) Physical Size mm 144.0(H)x 104.6(V) x 12.3(D) (typ.) Electrical Interface CMOS 6-bit Parallel RGB Surface Treatment Anti-Glare, Hardness 3H Support Color 262K colors The most suitable view angle 12 o'clock Temperature Range Operating Storage (Non-Operating) RoHS Compliance o C C o -30 to +85 -30 to +85 RoHS Compliance G057QN01 V0 Ver. 0.2 5/20 G057QN01 V0 2.2 Optical Characteristics (Room Temperature): The optical characteristics are measured under stable conditions at 25 Item Unit Conditions IF= 15mA / 1 LED line White Luminance [cd/m2] (center point) Uniformity Min. 5 Points % Contrast Ratio Response Time Viewing Angle Max. Remark 400 - Note 1 - 1.3 600 - [msec] Rising - 20 30 [msec] Falling - 15 20 [msec] Raising + Falling - 35 50 [degree] [degree] Horizontal CR = 10 (Right) (Left) 60 70 - 60 70 - [degree] [degree] Vertical CR = 10 (Upper) (Lower) 50 60 - 50 60 - White x 0.263 0.313 0.363 White y 0.279 0.329 0.379 Red x TBD TBD TBD Red y TBD TBD TBD Green x TBD TBD TBD Green y TBD TBD TBD Blue x TBD TBD TBD Blue y TBD TBD TBD - 50 - Color / Chromaticity Coordinates (CIE 1931) Color Gamut Typ. % Note 1, 2, 3 Note 4 Note 5 Note 6 Note 1: Measurement method Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent) Aperture 1 Test Point Center Environment < 1 lux with 50cm viewing distance LCD Module SR_3 or equivalent measuring distance Module Driving Equipment G057QN01 V0 Ver. 0.2 6/20 G057QN01 V0 Note 2: Definition of 5 points position (Display active area : 115.2mm(W) x 86.4mm(H)) W W /4 W /4 W /4 W /4 H /4 1 2 H /4 3 H H /4 5 4 H /4 Note 3: The luminance uniformity of 5 points is defined by dividing the minimum luminance values by the maximum test point luminance W5 Maximum Brightness of five points = Minimum Brightness of five points Note 4: Definition of contrast ratio (CR): Contrast ratio (CR)= Brightness on the "White" state Brightness on the "Black" state Note 5: Definition of response time: The output signals of photo detector are measured when the input signals are changed from "White" to "Black" (falling time) and from "Black" to "White" (rising time), respectively. The response time interval is between 10% and 90% of amplitudes. Please refer to the figure as below. % Tf Tr 100 90 Optical White Black White response 10 0 G057QN01 V0 Ver. 0.2 7/20 G057QN01 V0 Note 6: Definition of viewing angle Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). The 180 viewing angle range is broken down as below: 90 () horizontal left and right, and 90 () vertical high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated to its center to develop the desired measurement viewing angle. 3. Functional Block Diagram The following diagram shows the functional block of the G057QN01 V0 color TFT/LCD module: G057QN01 V0 Ver. 0.2 8/20 G057QN01 V0 4. Absolute Maximum Ratings 4.1 Absolute Ratings of TFT-LCD Module Item Symbol Min Max Unit Logic/LCD Drive Voltage Vin -0.3 +3.6 Volt LED backlight ILED 0 30 mA Unit 4.2 Absolute Ratings of Environment Item Symbol Min Max Operating Temperature TOP -30 +85 Operation Humidity HOP 5 95 Storage Temperature TST -30 +85 Storage Humidity HST 5 95 Note: Maximum Wet-Bulb should be 39 o C %RH o C %RH and no condensation. 5. Electrical Characteristics 5.1 TFT-LCD Driving 5.1.1 Power Specification Symbol Parameter Min Typ Max Units VDD Logic/LCD Drive Voltage 3.0 3.3 3.6 Volt IDD VDD Current - 210 - mA Irush LCD Inrush Current - - 1.5 A PDD VDD Power - 0.69 - Watt - - 100 VDDrp Remark All Black Pattern (VDD=3.3V, at 60Hz) Note 1 All Black Pattern Allowable Logic/LCD Drive Ripple Voltage (VDD=3.3V, at 60Hz) mV All Black Pattern p-p (VDD=3.3V, at 60Hz) Note 1: Measurement condition: G057QN01 V0 Ver. 0.2 9/20 G057QN01 V0 +3.3V Q3 AO6402 D6 D5 D2 D1 F1 S (LCD Module Input) G R1 47K VDD VCC C1 1uF/16V D1 D2 D5 D6 (High to Low) Control Signal Q3 AO6402 R2 S G 1K 2 C3 +12.0V SW1 1 SW MAG-SPST 0.01uF/25V VR1 R2 47K 1K C2 1uF/25V 3.3V 90% 10% 0V 0.5ms VDD rising time 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Parameter Symbol Min. Typ. Max. Unit Logic Input Voltage for High VIH 0.7VDD - VDD V Display Signals Low VIL 0 - 0.3VDD V High VIH 0.7VDD - VDD V Low VIL 0 - 0.3VDD V Remarks Input Voltage for RL/UD G057QN01 V0 Ver. 0.2 10/20 G057QN01 V0 5.2 Backlight Unit Driving 5.2.1 Parameter guideline for LED (Room Temperature): Following characteristics are measured under a stable condition using an LED driving board at 25 Symbol Parameter IF Min LED forward current VF LED Power Operating Life Max Unit 15 mA Remark o Ta = 25 C o 27.6 TBD V IF = 15mA, Ta = -30 C 26.4 TBD V IF = 15mA, Ta = 25 C 25.2 TBD V IF = 15mA, Ta = 85 C - 1.5 - Watt 20000 40000 LED forward voltage PLED Typ Hrs o o o IF = 15mA, Ta = 25 C Note 1: IF is defined for one channel LED. There are total three LED channels in back light unit. Note 2: G057QN01 V0 can be operated at operating temperature range, but optical performance should be evaluated at o Ta = 25 C only. o Note 3: When G057QN01 V0 module is operated at high ambient temperature condition (over 25 C), LED forward current IF should be less than 15 mA to avoid over LED junction temperature spec. Note 4: If LED is driven by high current, high ambient temperature & humidity condition. The life time of LED will be reduced. Note 5: Operating life means brightness goes down to 50% initial brightness. Typical operating life time is estimated data. 6. Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format. G057QN01 V0 Ver. 0.2 11/20 G057QN01 V0 6.2 Scanning Direction The following figures show the image seen from the front view. The arrow indicates the direction of scan. 6.3 The Input Data Format This product displays 262,144 colors in terms of the 64 grey levels on RGB respectively. The following table demonstrates the display of input data G057QN01 V0 Ver. 0.2 12/20 G057QN01 V0 6.4 TFT- LCD Interface Signal Description PIN No. Symbol Pin Description 1 GND Ground 2 CLK Dot clock 3 NC No Connection 4 NC No Connection 5 GND Ground 6 R0 Red data (LSB) 7 R1 Red data 8 R2 Red data 9 R3 Red data 10 R4 Red data 11 R5 Red data (MSB) 12 GND Ground 13 G0 Green data (LSB) 14 G1 Green data 15 G2 Green data 16 G3 Green data 17 G4 Green data 18 G5 Green data (MSB) 19 GND Ground 20 B0 Blue data (LSB) 21 B1 Blue data 22 B2 Blue data 23 B3 Blue data 24 B4 Blue data 25 B5 Blue data (MSB) 26 GND Ground 27 DE Data Enable Signal 28 VDD Power supply (3.3V Typ. ONLY) 29 VDD Power supply (3.3V Typ. ONLY) 30 R/L Horizontal reverse scan (L: Normal, H: Right & Left reversal) 31 U/D Vertical reverse scan (H: Normal, L: Up & Down reversal) 32 NC No Connection 33 GND Ground G057QN01 V0 Ver. 0.2 13/20 G057QN01 V0 Note 1: Input signals shall be in low status when VDD is off. Note 2: NC = No Connection 6.5 TFT- LCD Interface Timing 6.5.1 Timing Characteristics DE mode only Signal Symbol Min. Typ. Max. Unit Remark Clock frequency (DOTCLK) 1/ TCLOCK 6.2 6.4 12.1 MHz Note1 Period TH 406 408 560 Active THD TCLOCK Note1 Blanking THB 86 88 240 Period TV 254 263 360 Active TVD TLINE Note1 Blanking TVB Horizontal Section Vertical Section 320 240 14 23 120 Note 1: Frame rate is 60 Hz. 6.5.2 Input Timing Diagram Input Timing Definition ( DE Mode) TCLOCK DOTCLK Input Data Invaild Data Pixel 1 Pixel 2 Pixel 3 Pixel N-1 Pixel N Invaild Data Pixel 1 DE THB THD TH DE TVB TVD TV G057QN01 V0 Ver. 0.2 14/20 G057QN01 V0 6.6 LED Backlight Unit Interface Pin # Symbol Pin Description 1 AN1 Anode 1 2 AN2 Anode 2 3 AN3 Anode 3 4 CA1 Cathode 1 5 CA2 Cathode 2 6 CA3 Cathode 3 6.7 Power ON/OFF Sequence VDD power and LED on/off sequence is as below. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Power ON/OFF sequence timing Value Parameter Units Min. Typ. Max. T1 0.5 - 10 ms T2 0 - 50 ms T3 0 - 50 ms T4 0 - 10 ms T5 200 - - ms T6 200 - - ms T7 500 - - ms The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. G057QN01 V0 Ver. 0.2 15/20 G057QN01 V0 7. Connector & Pin Assignment 7.1 TFT- LCD Signal (CN1): LCD Connector Connector Name / Designation Signal Connector Manufacturer Hirose or compatible Connector Model Number FH12-33S-0.5SH(55) or compatible Pin# Symbol Pin# Symbol Pin# Symbol 1 GND 12 GND 23 B3 2 CLK 13 G0 24 B4 3 NC 14 G1 25 B5 4 NC 15 G2 26 GND 5 GND 16 G3 27 DE 6 R0 17 G4 28 VDD 7 R1 18 G5 29 VDD 8 R2 19 GND 30 R/L 9 R3 20 B0 31 U/D 10 R4 21 B1 32 NC 11 R5 22 B2 33 GND 7.2 LED Backlight Unit (CN2): LED Connector Connector Name / Designation Lamp Connector Manufacturer JST or compatible Connector Model Number SHLP-06V-S-B or compatible Mating Model Number SM06B-SHLS-TF or compatible Pin # Symbol Cable color Pin # Symbol Cable color 1 AN1 Red 4 CA1 Blue 2 AN2 Red 5 CA2 White 3 An3 Red 6 CA3 Black G057QN01 V0 Ver. 0.2 16/20 G057QN01 V0 7.3 PIN 1 definition of CN1 and CN2 8. Reliability Test Criteria Items Required Condition Remark Cold Start Test /90%,300Hr 85,300Hr -30,300Hr 85,300 hours -30,300 hours -20/30 min ,60/30 min ,100cycles 85/1 Hr (min.), power on/off per 5 minutes, repeat 5 times -30/1 Hr (min.), power on/off per 5 minutes, repeat 5 times Shock Test (Non-Operating) 50G,20ms,Half-sine wave,(+-X,+-Y,+-Z) Note 2 1.5G, 10~200~10Hz, Sine wave, 30mins/axis, 3 direction (X, Y, Z) Note 2 Temperature Humidity Bias High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Thermal Shock Test Hot Start Test 40 Note 2 Note 2 Note 2 Note 2 Note 2 Note 2 Note 2 Note 2 Vibration Test (Non-Operating) ESD Contact : 8KV/ operation, Class B; Air : 15KV / operation, Class B (RL=150, CL=330pF) Attitude Test Operating: 14,000 ft, Ramp: 2000 ft/min, 8hrs Non-operating: 40,000 ft, Ramp: 2000 ft/min, 24hrs Note 1,2 Note 2 Note1: According to EN61000-4-2 ESD class B criteria, some performance degradation is allowed. No data lost, Self-recoverable. No hardware failures. G057QN01 V0 Ver. 0.2 17/20 G057QN01 V0 Note2: Water condensation is not allowed for each test items. Each test is done by new TFT-LCD module. Please don't use the same TFT-LCD module repeatedly for reliability test. The reliability test is performed only to examine the TFT-LCD' module. To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24 hour at least in advance. G057QN01 V0 Ver. 0.2 18/20 G057QN01 V0 9. Mechanical Characteristics G057QN01 V0 Ver. 0.2 19/20 G057QN01 V0 10. Label and Packaging 10.1 Shipping Label (on the rear side of TFT-LCD display) TBD 10.2 Carton Package TBD 11 Safety 11.1 Sharp Edge Requirements There will be no sharp edges or corners on the display assembly that could cause injury. 11.2 Materials 11.2.1 Toxicity There will be no carcinogenic materials used anywhere in the TFT-LCD module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist. 11.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the TFT-LCD module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 11.3 Capacitors If any polarized capacitors are used in the TFT-LCD module, provisions will be made to keep them from being inserted backwards. 11.4 National Test Lab Requirement The TFT-LCD module will satisfy all requirements for compliance to UL 60950 (U.S.A. Information Technology Equipment). G057QN01 V0 Ver. 0.2 20/20