Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC506LP4 / 506LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 7.8 - 8.7 GHz Typical Applications Features Low noise MMIC VCO w/Buffer Amplifier for: Pout: +14 dBm * VSAT Radio Phase Noise: -103 dBc/Hz @100 KHz * Point to Point/Multipoint Radio No External Resonator Needed * Test Equipment & Industrial Controls Single Supply: +3V @ 77 mA * Military End-Use QFN Leadless SMT Package, 16 mm2 Functional Diagram General Description The HMC506LP4 & HMC506LP4E are GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCOs with integrated resonators, negative resistance devices, varactor diodes, and buffer amplifiers. Covering 7.8 to 8.7 GHz, the VCO's phase noise performance is excellent over temperature, shock and vibration due to the oscillator's monolithic structure. Power output is +14 dBm typical from a single supply of +3.0V @ 77 mA. The voltage controlled oscillator is packaged in a leadless QFN 4 x 4 mm surface mount package. VCOS & PLOs - SMT 11 Electrical Specifi cations, TA = +25 C, Vcc = +3V Parameter Min. Frequency Range Power Output 11.0 SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RF Output Tune Voltage (Vtune) Supply Current (Icc) (Vcc = +3.0V) Typ. GHz dBm -103 1 dBc/Hz 11 77 V mA 10 A 7 dB Harmonics 2nd 3rd -16 -28 dBc dBc Pulling (into a 2.0:1 VSWR) 28 MHz pp Pushing @ Vtune= +5V 78 MHz/V 0.85 MHz/C Frequency Drift Rate 11 - 102 Units 14.0 Tune Port Leakage Current Output Return Loss Max. 7.8 - 8.7 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC506LP4 / 506LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 7.8 - 8.7 GHz Frequency vs. Tuning Voltage, T= 25C Frequency vs. Tuning Voltage, Vcc= +3V 9.2 9 9 8.8 8.8 FREQUENCY (GHz) 8.6 8.4 8.2 8 7.8 2.75V 3.0V 3.25V 7.6 8.6 8.4 8.2 8 7.8 +25C +85C -40C 7.6 7.4 7.4 7.2 7.2 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 TUNING VOLTAGE (VOLTS) Sensitivity vs. Tuning Voltage, Vcc= +3V 6 7 8 9 10 11 11 20 360 18 320 OUTPUT POWER (dBm) SENSITIVITY (MHz/VOLT) 5 Output Power vs. Tuning Voltage, Vcc= +3V 400 +25C +85C -40C 280 240 200 160 120 16 14 12 10 +25C +85C -40C 8 80 6 40 0 1 2 3 4 5 6 7 8 9 10 0 11 1 2 3 TUNING VOLTAGE (VOLTS) 4 5 6 7 8 9 10 11 TUNING VOLTAGE (VOLTS) Phase Noise vs. Tuning Voltage Typical SSB Phase Noise @ Vtune= +5V -65 0 10kHz offset 100kHz offset -75 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) 4 TUNING VOLTAGE (VOLTS) VCOS & PLOs - SMT FREQUENCY (GHz) 9.2 -85 -95 -20 -40 +25C +85C -40C -60 -80 -100 -105 -120 -115 -140 -125 0 1 2 3 4 5 6 7 8 TUNING VOLTAGE (VOLTS) 9 10 11 -160 3 10 4 10 5 10 6 10 7 10 OFFSET FREQUENCY (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 - 103 HMC506LP4 / 506LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 7.8 - 8.7 GHz Absolute Maximum Ratings Vcc +3.5 Vdc Vcc (V) Icc (mA) Vtune 0 to +11V 2.75 66 Channel Temperature 135 C 3.0 77 Continuous Pdiss (T = 85C) (derate 6.07 mW/C above 85C) 303 mW 3.25 88 Thermal Resistance (junction to ground paddle) 165 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C Note: VCO will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing VCOS & PLOs - SMT 11 Typical Supply Current vs. Vcc NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC506LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC506LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H506 XXXX [2] H506 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 11 - 104 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC506LP4 / 506LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 7.8 - 8.7 GHz Pin Descriptions Function Description 1- 14, 17 - 19, 21, 23, 24 N/C No Connection 15 GND This pin must be connected to RF & DC ground. 16 RFOUT RF output (AC coupled) 20 Vcc Supply Voltage Vcc= 3V 22 VTUNE Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. GND Package bottom has an exposed metal paddle that must be RF & DC grounded. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 VCOS & PLOs - SMT Pin Number 11 - 105 HMC506LP4 / 506LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 7.8 - 8.7 GHz Evaluation PCB VCOS & PLOs - SMT 11 List of Materials for Evaluation PCB 105706 [1] Item Description J1 - J2 PCB Mount SMA RF Connector J3 - J4 DC Pin C1 4.7 F Tantalum Capacitor C2 10,000 pF Capacitor, 0603 Pkg. U1 HMC506LP4 / HMC506LP4E VCO PCB [2] 105667 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 11 - 106 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC506LP4 / 506LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 7.8 - 8.7 GHz Notes: VCOS & PLOs - SMT 11 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 - 107 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC506LP4E HMC506LP4 HMC506LP4ETR 105706-HMC506LP4 HMC506LP4TR