DataSheet
PCB Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
PF Series
• SIP SSR
• Ratings to 25A (forced air) @ 480 VAC
• SCR output for heavy industrial loads
• AC or DC control
• Zero-crossing (resistive loads) or random-fire (inductive loads) output
PRODUCT SELECTION
Control Voltage
3-15 VDC
AVAILABLE OPTIONS
OUTPUT SPECIFICATIONS (1)
Description
Operating Voltage (47-63Hz) [Vrms] 48-660
Transient Overvoltage [Vpk] 1200
Maximum Off-State Leakage Current @ Rated Voltage [mArms] 0.1
Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (2) 500
Maximum Load Current (Convection Air) [Arms] (3) 10
Maximum Load Current (Forced Air) [Arms] (3) 25
Minimum Load Current [Arms] 0.06
Maximum Surge Current (16.6ms) [Apk] 250
Maximum I²t for fusing (8.3 msec) [A² sec]
25 A25 A 25 A
PF240D25
4-15 VDC PF480D25
PF380D25
15-32 VDC PFE480D25
PFE380D25PFE240D25
18-36 VAC PFE240A25
90-140 VAC PF240A25
12-280
600
0.1
500
10
25
250
0.06
1.6
Maximum On-State Voltage Drop @ Rated Current [Vpk]
260
48-530
1200
0.1
500
10
25
0.06
250
1.6
260
1.6
260
Minimum Power Factor (with Maximum Load) 0.50.5
0.5
Required for valid part number
For options only and not required for valid part number
Series
Operational Current
25: 25 Amps
Operational Voltage
240: 12-280 VAC
380: 48-530 VAC
480: 48-660 VAC
Control Input Type
D: DC Input
A: AC Input
PF 240
Output Type
Blank: Normally Open
-B: Normally Closed
(PF480D25 only)
-B
D 25
Switching Mode
Blank: Zero Voltge Turn-On
R: Random Turn-On
R
Control Voltage
Blank: 3-15 VDC
(240,D suffix only)
4-15 VDC
(380/480,D suffix only)
90-140 VAC (A suffix only)
E: 15-32 VDC (D suffix only)
18-36 VAC (A suffix only)
E
PF380 PF480PF240
FDE-07-01 REV. A
Do not forget to visit us at:
www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
INPUT SPECIFICATIONS (1)
PF240A25Description
Control Voltage Range [VDC] 90-140 VAC
90.0 Vrms
Typical Input Current @ Nominal Voltage
Maximum Turn On Voltage
Nominal Input Impedance
10 mAdc
Maximum Turn-Off Time [msec]
14.1 k Ohm
40
PFE240A25
Minimum Turn-Off Voltage 10.0 Vrms
Maximum Turn-On Time [msec] (4) 10
18-36 VAC
18.0 Vrms
10 mAdc
2.1 k Ohm
40
2.0 Vrms
10
PFExxxD25
15-32 VDC
15.0 VDC
15 mAdc
1500 Ohm
1/2 Cycle
1.0 VDC
1/2 Cycle
PF380D/480D
4-15 VDC
4.0 VDC
15 mAdc
240 Ohm
1/2 Cycle
1.0 VDC
1/2 Cycle
PF240D25
3-15 VDC
3.0 VDC
15 mAdc
300 Ohm
1/2 Cycle
1.0 VDC
1/2 Cycle
GENERAL SPECIFICATIONS
ParametersDescription
Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms
Minimum Insulation Resistance (@ 500 V DC) 10 9 Ohms
Maximum Capacitance, Input/Output 8 pF
Ambient Operating Temperature Range -30ºC to 80ºC
Ambient Storage Temperature Range -30ºC to 125ºC
1.02 oz. (29g)Weight (typical)
Thermally Conductive Epoxy
Encapsulation
GENERAL NOTES
1) All parameters at 25°C unless otherwise specified.
2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
3) Heatsink temperature 85°C Maximum for 25A forced air cooling.
4) Turn-On Time for Random Turn-On versions 0.1 msec (DC Control Models)
WIRING DIAGRAM
LOAD
TRIGGER
CIRCUIT
4
BA
AC
-DC +DC
Load can be wired in location A or B
AC
21
LOAD
3
Load can be wired in location A or B
LOAD
TRIGGER
CIRCUIT
4V
LOAD
BA
AC
AC AC
AC
2 1
AC/DC
Converter
3
DataSheet
PCB Mount
DataSheet
PCB Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
THERMAL DERATE INFORMATION
Designed in accordance with the requirements of IEC 62314
AGENCY APPROVALS
Agency Approvals
MECHANICAL SPECIFICATIONS
Tolerances: ±0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]
AMBIENT TEMPERATURE (ºC)
FIG.1 Convection Cooling FIG.2 Forced Air Cooling
8
4
2010 4030 60 7050 80
0
LOAD CURRENT (AMPS)
10
6
2
HEATSINK TEMPERATURE (˚C)
LOAD CURRENT (AMPS)
20
10
4020 8060 120 140100
00
25
15
5
1.35
MAX
(34.3)
.05
(1.3)
1.6 TYP.
(38.1)
1.6 TYP.
(38.1)
Rev. 081017
ECN 20296
E116950 REG.-Nr. 70938 (240 V, 380 V, DC Control Only)
DataSheet
PCB Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
•Disconnect all
power before
installing or
working with
this equipment.
•Verify all
connections
and replace all
covers before
turning on
power.
Failure to follow
these
instructions will
result in death
or serious injury.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
•Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
con este equipo.
•Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
el equipo.
El
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
RISQUE DE
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
•Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
•Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
Gerät Arbeiten
durchführen
•Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
Abdeckungen
ersetzen.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
Verletzungen
führen.
存在电击、
爆炸或电弧
闪烁危险
•
在操作此设
备之前请先
关闭电源。
若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
Fremdkörper in das Produkt ein.
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。
材料损坏和高温外壳的危险性
• 产品的一侧面板可能很热，在其冷却前请
不要触碰。
• 遵照正确的安装说明，包括扭矩值。
• 请勿让液体及其他异物进入本产品。
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.
•Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa
apparecchiatura
•Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima
dell’accensione
L'omissione di
queste istruzioni
provocherà la
morte o
lesioni serie
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
DataSheet
PCB Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
ANNEX - ENVIRONMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated
(Pb) (Hg) (Cd) Chromium
(Cr (VI))
biphenyls
(PBB)
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
有毒有害物质或元素件部
名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)
半导体芯片
焊接点
50
