Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors KPS MIL Series, SMPS Stacked Capacitors, MIL-PRF-49470, DSCC 87106, 50VDC-500VDC (Commercial, Military, & Space Grades) Overview KEMET Power Solutions (KPS) MIL Series ceramic stacked capacitors are available in commercial, military and space grades and are well suited for standard and high reliability switch mode power supply (SMPS) and pulse energy applications. Qualified under performance specification MIL-PRF-49470, our military and space grade products meet or exceed the requirements outlined by DSCC (Defense Supply Center, Columbus) and are available in both B (standard reliability) & T (high reliability) product levels. MIL-PRF-49470 was developed as part of a cooperative effort between the U.S. Military, NASA and SMPS suppliers to produce a robust replacement to cancelled DSCC Drawing 87106. The KPS MIL Series is constructed using large chip multilayer ceramic capacitors (MLCCs), horizontally stacked and secured to a lead-frame termination system using a high melting point (HMP) solder alloy. The lead frame isolates the MLCCs from the Benefits * * * * * * * * * * * * * * -55C to +125C operating temperature range High frequency performance Bulk capacitance in a reduced footprint MIL-PRF-49470 QPL Military Case Codes 3, 4 and 5 Space Grade available ("T" Level) DSCC approved (87106) Commercial/Industrial Grade available Customer specific requirements available Low ESR and ESL High thermal stability High ripple current capability Higher reliability than aluminum electrolytic or tantalum Available encapsulated or unencapsulated One WORLD One Brand One Strategy printed circuit board (PCB) while establishing a parallel circuit configuration. Mechanically isolating the capacitors from the PCB improves mechanical and thermal stress performance, while the parallel circuit configuration allows for bulk capacitance in the same or smaller design footprint. Available in BX, BR, BQ, and X7R dielectrics, these devices are available in encapsulated and unencapsulated styles in both surface mountable and through-hole configurations. Their low Equivalent Series Resistance (ESR) and Equivalent Series Inductance (ESL) make them ideally suited for input and output filtering of power supply as well as snubber applications. The encapsulated styles are primarily used where increased mechanical and environmental protection is required, such as in avionics systems. Applications * * * * Military Space Industrial Input and output filtering on power supplies - often found on "capacitor banks" * Snubber circuits * Radar filtering (28V/microwave burst) One Focus One Team One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 1 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors MIL-PRF-49470 Ordering Information M49470 R 01 474 K Performance Specification Dielectric Classification/ Performance Specification Sheet Capacitance Indicating MIL-PRF-494701 Characteristic2 Number (Indicating MIL-PRF-49470/1)3 Code (pF) M49470 = B level T49470 = T level A "T" prefix is used in place of the "M" for T level product. Q = BQ R = BR X = BX 01 = Unencapsulated 02 = Encapsulated 2 Sig. Digits + Number of Zeros C Capacitance Rated Tolerance Voltage (DC) J = 5% K = 10% M = 20% A = 50V B = 100V C = 200V E = 500V N Lead Configuration4 N = Straight Pin L = Formed "L" M= Formed "L" J= Formed "J" K= Formed "J" Indicates performance and reliability requirements. "B" level represents standard reliability."T" level represents high reliability. Please refer to performance specification sheet MIL-PRF-49470 for details regarding test levels. The latest revision of the specification sheet is available through DSCC. 1, 3 Test level option "T" is not available on encapsulated stacked devices (i.e. MIL-PRF-49470/2). 2 Dielectric classification and characteristic details are outlined in the "Electrical Parameters" section of this document. 4 Lead configuration and dimension details are outlined in the "Dimensions" section of this document. 1 1 KPS MIL Series, SMPS Stacks Ordering Information (Do not use this ordering code if a QPL MIL-SPEC part type is required. Please order using MIL-SPEC ordering code. Details regarding MIL-PRF-49470 QPL ordering information is outlined above.) L1 R N 30 C 106 K Dielectric Lead Product Family1 Classification/ 3 2 Configuration Characteristic Case Size / Rated Capacitance Capacitance Case Code Voltage (DC) Code (pF) Tolerance (CC) L1 = Unencapsulated L2 = Encapsulated 30 = CC 3 40 = CC 4 50 = CC 5 Q = BQ R = BR X = BX W = X7R N = Straight L = Formed "L" M= Formed "L" J= Formed "J" K= Formed "J" 3 = 25V 2 Sig. Digits J = 5% 5 = 50V + Number of K = 10% 1 = 100V Zeros M = 20% 2 = 200V C = 500V B = 630V D = 1000V S 12 Testing Option4 Maximum Height Dimension (in.)5 B = M49470 "B" Level Unencapsulated Encapsulated T = M49470 "T" Level 12 = 0.12" 27 = 0.27" C = DSCC87106 24 = 0.24" 39 = 0.39" S = Commercial 36 = 0.36" 53 = 0.53" X = Non-Standard 48 = 0.48" 66 = 0.66" (Customer Specific 65 = 0.65" 80 = 0.80" Requirements) , Test level option "T" is not available on encapsulated stacked devices, i.e., MIL-PRF-49470/2. If a QPL MIL-Spec part type is required, please order using the MIL-Spec ordering code. 2 Dielectric classification and characteristic details are outlined in the ""Electrical Parameters"" section of this document. 3 Lead configuration and dimension details are outlined in the "Dimensions" section of this document. Additional lead configurations may be available. Contact KEMET for details. 4 Indicates performance and reliability requirements. Testing option details are outlined in the "Performance and Reliability" section of this document. 4 Please refer to performance specification sheet MIL-PRF-49470 for additional details regarding test levels. The latest revision of the specification sheet is available through DSCC. 4 DSCC Drawing 87106 was cancelled on 01/03/2005. MIL-PRF-49470 capacitors are preferred over DSCC Drawing 87106 capacitors. 5 Maximum height dimensions are provided in product tables 1A, 1B, and 1C of this document 1 4 Ordering Information Requirements per DSCC Drawing 87106 DSCC Drawing 87106 was cancelled on 01/03/2005. Customers can continue to order per 87106 requirements using the original DSCC ordering code,i.e., 87106-001. When available, MIL-PRF-49470 devices are preferred over DSCC Drawing 87106. The MIL-PRF-49470 military specification product provides additional quality assurance provisions that are not required by the DSCC drawing. These extra provisions create a more robust replacement. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 2 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Construction Note: Image is exaggerated in order to clearly identify all components of construction 1 2 Reference Item Material A B C D E F G H J K Leadframe Leadframe Attach Solder Phosphor Bronze - Alloy 510 Sn10, Pb88, Ag2 SnPb (4% min.) Ni Solderable Silver Ag PdAg BaTiO3 Sn60, Pb40 Molding Compound Diallyl-Phthalate (DAP) Termination System1 Electrode Dielectric Lead Solder Encapsulation2 KEMET reserves the right to construct these devices using either of the termination systems outlined. Encapsulated product only, i.e., MIL-PRF-49470/2 and L2 product families. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 3 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Unencapsulated (M49470/1 & L1) Product Dimensions - Inches (Millimeters) 1 Case Code C Lead Spacing 0.025 (0.635) E Length 0.010 (0.250) D Width Min. D Width Max. A Height Max. 3 0.450 (11.43) 0.500 (12.70) 0.950 (24.13) 1.075 (27.30) 4 0.400 (10.16) 0.440 (11.18) 0.350 (8.89) 0.425 (10.80) 5 0.250 (6.35) 0.300 (7.62) 0.224 (5.69) 0.275 (6.98) Refer to tables 1A & 1C for specific maximum A dimension Seating Plane1 0.010 (0.250) Number of Leads per Side Mounting Technique 10 0.055 (1.40) 4 Solder reflow only 3 Only applies to lead style "N" (straight). 3 3 5 4 1. Unless otherwise specified, tolerances are .010" (0.25mm). 2. Metric equivalents for C, D and E dimensions are provided for general information only. 3. For maximum B dimension, add .065" (1.65mm) to the appropriate A dimension. For all lead styles, the number of chips is determined by the capacitance and voltage rating. 4. For case code 5, dimensions shall be .100" (2.54mm) maximum and .012" (0.30mm) minimum. 5. Lead alignment within pin rows shall be within .005" (0.13mm). Unencapsulated & Encapsulated Lead Configurations - Inches (Millimeters) Lead Style Symbol Lead Style L Lead Length N (N) Straight 0.250 Min. (6.35) L (L) Formed 0.070 0.010 (1.78 0.25) M J K 0.045 0.010 (1.14 0.25) (J) Formed 0.070 0.010 (1.78 0.25) 0.045 0.010 (1.14 0.25) Additional lead configurations may be available. Contact KEMET for details. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 4 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Encapsulated (M49470/2 & L2) Product Dimensions - Inches (Millimeters) Case Code C Lead Spacing 0.025 (0.635) E Length Max. D Width 0.635 (0.025) 3 0.450 (11.43) 0.580 (14.73) 1.155 (29.34) 4 0.400 (10.16) 0.485 (12.32) 0.485 (12.32) 5 0.250 (6.35) 0.355 (9.02) 0.355 (9.02) A Height Number of Leads per Side Mounting Technique 10 Solder reflow only Refer to table 1B for specific maximum A dimension 4 3 SEE NOTE 4 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010" (0.25mm). 4. Lead alignment within pin rows shall be within .005" (0.13mm). Unencapsulated & Encapsulated Lead Configurations - Inches (Millimeters) Lead Style Symbol N L M J K Lead Style (N) Straight (L) Formed (J) Formed L Lead Length 0.250 Min. (6.35) 0.070 0.010 (1.78 0.25) 0.045 0.010 (1.14 0.25) 0.070 0.010 (1.78 0.25) 0.045 0.010 (1.14 0.25) Additional lead configurations may be available. Contact KEMET for details. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 5 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Qualification Inspection Per MIL-PRF-49470 Inspection Test Method Paragraph Group I Thermal shock and voltage conditioning 4.8.5 Group II Visual and mechanical Inspection 4.8.4 Group III Low temperature storage Barometric pressure Terminal strength 4.8.23 4.8.9 4.8.10 Group IV Voltage-temperature limits 4.8.13.1 Vibration, high frequency 4.8.14 Immersion 4.8.15 Group V Shock, specified pulse 4.8.16 Resistance to soldering heat 4.8.17 Moisture resistance 4.8.18 Group VI DPA (T level only) 4.8.19 Group VII Humidity, steady state, low voltage (T level only) 4.8.21 Group VIII Life 4.8.22 Environmental Compliance These devices do not meet RoHS criteria (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 6 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Electrical Parameters/Performance Characteristics: BQ Dielectric Item Parameters/Characteristics Operating Temperature Range Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) Capacitance Change with Reference to +25C and 100% Rated VDC Applied Aging Rate (Max % Cap Loss/Decade Hour) Dielectric Withstanding Voltage Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C Insulation Resistance (IR) Limit @ 125C -55C to +125C 15% +15%, -50% 1% 250% of rated DC voltage for voltage rating < 500V 150% of rated DC voltage for voltage rating of 500V (5 1 seconds and charge/discharge not exceeding 50mA) 2.5% 1000 megohm microfarads (minimum) or 100G 100 megohm microfarads (minimum) or 10G Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and Dissipation Factor (DF) measured under the following conditions: 1kHz 100Hz at 1.0Vrms 0.2 Vrms (open circuit voltage). Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." Electrical Parameters/Performance Characteristics: BR Dielectric Item Parameters/Characteristics Operating Temperature Range Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) Capacitance Change with Reference to +25C and 100% Rated VDC Applied Aging Rate (Max % Cap Loss/Decade Hour) Dielectric Withstanding Voltage Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C Insulation Resistance (IR) Limit @ 125C -55C to +125C 15% +15%, -40% 1% 250% of rated DC voltage for voltage rating < 500V 150% of rated DC voltage for voltage rating of 500V (5 1 seconds and charge/discharge not exceeding 50mA) 2.5% 1000 megohm microfarads (minimum) or 100G 100 megohm microfarads (minimum) or 10G Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and Dissipation Factor (DF) measured under the following conditions: 1kHz 100Hz at 1.0Vrms 0.2 Vrms (open circuit voltage). Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 7 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Electrical Parameters/Performance Characteristics: BX Dielectric Item Parameters/Characteristics Operating Temperature Range Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) Capacitance Change with Reference to +25C and 100% Rated VDC Applied Aging Rate (Max % Cap Loss/Decade Hour) Dielectric Withstanding Voltage Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C Insulation Resistance (IR) Limit @ 125C -55C to +125C 15% +15%, -25% 1% 250% of rated DC voltage for voltage rating < 500V 150% of rated DC voltage for voltage rating of 500V (5 1 seconds and charge/discharge not exceeding 50mA) 2.5% 1000 megohm microfarads (minimum) or 100G 100 megohm microfarads (minimum) or 10G Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and Dissipation Factor (DF) measured under the following conditions: 1kHz 100Hz at 1.0Vrms 0.2 Vrms (open circuit voltage). Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." Electrical Parameters/Performance Characteristics: X7R Dielectric Item Parameters/Characteristics Operating Temperature Range -55C to +125C Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) 15% Aging Rate (Max % Cap Loss/Decade Hour) 3.0% Dielectric Withstanding Voltage Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C 250% of rated voltage (5 1 seconds and charge/discharge not exceeding 50mA) 3.5% (25V) and 2.5% (50V to 200V) 1000 megohm microfarads or 100G (Rated voltage applied for 120 5 secs @ 25C) Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and Dissipation Factor (DF) measured under the following conditions: 1kHz 50Hz and 1.0 0.2 Vrms if capacitance 10F. 20Hz 10Hz and 0.5 0.1 Vrms if capacitance >10F. Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 8 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1A - MIL-PRF-49470/1, Product Selection 50VDC-200VDC MIL-PRF-49470/1 Unencapsulated, Horizontally Stacked MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) (1)49470X01105(2)A(3) (1)49470X01125(2)A(3) (1)49470X01155(2)A(3) (1)49470X01185(2)A(3) (1)49470X01225(2)A(3) (1)49470X01275(2)A(3) (1)49470X01335(2)A(3) (1)49470X01475(2)A(3) (1)49470X01395(2)A(3) (1)49470X01565(2)A(3) (1)49470X01685(2)A(3) (1)49470X01825(2)A(3) (1)49470X01106(2)A(3) (1)49470X01126(2)A(3) (1)49470X01156(2)A(3) (1)49470X01186(2)A(3) (1)49470X01226(2)A(3) (1)49470X01276(2)A(3) (1)49470X01336(2)A(3) (1)49470X01396(2)A(3) (1)49470X01476(2)A(3) 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 3.9 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 5 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 (1)49470X01684(2)B(3) (1)49470X01824(2)B(3) (1)49470X01105(2)B(3) (1)49470X01125(2)B(3) (1)49470X01155(2)B(3) (1)49470X01185(2)B(3) (1)49470X01225(2)B(3) (1)49470X01275(2)B(3) (1)49470X01335(2)B(3) (1)49470X01395(2)B(3) (1)49470X01475(2)B(3) (1)49470X01565(2)B(3) (1)49470X01685(2)B(3) (1)49470X01825(2)B(3) (1)49470X01106(2)B(3) (1)49470X01126(2)B(3) (1)49470X01156(2)B(3) (1)49470X01186(2)B(3) (1)49470X01226(2)B(3) (1)49470X01276(2)B(3) 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 (1)49470R01474(2)C(3) (1)49470R01564(2)C(3) (1)49470R01684(2)C(3) (1)49470R01824(2)C(3) (1)49470R01105(2)C(3) 0.47 0.56 0.68 0.82 1 5 5 5 5 5 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) Lead Config. KEMET P/N 1 N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1X(3)505105(2)(4)12 L1X(3)505125(2)(4)12 L1X(3)505155(2)(4)24 L1X(3)505185(2)(4)24 L1X(3)505225(2)(4)24 L1X(3)505275(2)(4)36 L1X(3)505335(2)(4)36 L1X(3)505475(2)(4)48 L1X(3)505395(2)(4)48 L1X(3)505565(2)(4)65 L1X(3)405685(2)(4)36 L1X(3)405825(2)(4)36 L1X(3)405106(2)(4)48 L1X(3)405126(2)(4)48 L1X(3)405156(2)(4)65 L1X(3)305186(2)(4)24 L1X(3)305226(2)(4)36 L1X(3)305276(2)(4)36 L1X(3)305336(2)(4)36 L1X(3)305396(2)(4)48 L1X(3)305476(2)(4)65 N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1X(3)501684(2)(4)12 L1X(3)501824(2)(4)24 L1X(3)501105(2)(4)24 L1X(3)501125(2)(4)24 L1X(3)501155(2)(4)36 L1X(3)501185(2)(4)36 L1X(3)501225(2)(4)48 L1X(3)501275(2)(4)48 L1X(3)501335(2)(4)65 L1X(3)401395(2)(4)36 L1X(3)401475(2)(4)36 L1X(3)401565(2)(4)48 L1X(3)401685(2)(4)48 L1X(3)401825(2)(4)65 L1X(3)301106(2)(4)24 L1X(3)301126(2)(4)24 L1X(3)301156(2)(4)36 L1X(3)301186(2)(4)36 L1X(3)301226(2)(4)48 L1X(3)301276(2)(4)65 K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1R(3)502474(2)(4)24 L1R(3)502564(2)(4)24 L1R(3)502684(2)(4)36 L1R(3)502824(2)(4)36 L1R(3)502105(2)(4)48 Cap Tolerance Lead Config. KEMET P/N 1 Cap Tol. 50VDC - BX Dielectric 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M 100VDC - BX Dielectric 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M 200VDC - BR Dielectric Complete P/N requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test level character "M" for B level, or "T" for T level (MIL-PRF-49470/1 part number only) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" (4) Test level character "B" for B level, or "T" for T level (KEMET part number only) 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 Roll Over for Order Info. 9 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1A - MIL-PRF-49470 /1, Product Selection 200VDC-500VDC con't. MIL-PRF-49470/1 Unencapsulated, Horizontally Stacked MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tol. Lead Config. KEMET P/N 1 (1)49470R01125(2)C(3) (1)49470R01155(2)C(3) (1)49470R01185(2)C(3) (1)49470R01225(2)C(3) (1)49470R01275(2)C(3) (1)49470R01335(2)C(3) (1)49470R01395(2)C(3) (1)49470R01475(2)C(3) (1)49470R01565(2)C(3) (1)49470R01685(2)C(3) (1)49470R01825(2)C(3) (1)49470R01106(2)C(3) (1)49470R01126(2)C(3) 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 5 5 4 4 4 4 4 3 3 3 3 3 3 0.480 (12.19) 0.650 (16.51) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1R(3)502125(2)(4)48 L1R(3)502155(2)(4)65 L1R(3)402185(2)(4)36 L1R(3)402225(2)(4)36 L1R(3)402275(2)(4)48 L1R(3)402335(2)(4)48 L1R(3)402395(2)(4)65 L1R(3)302475(2)(4)24 L1R(3)302565(2)(4)24 L1R(3)302685(2)(4)36 L1R(3)302825(2)(4)36 L1R(3)302106(2)(4)48 L1R(3)302126(2)(4)65 (1)49470Q01154(2)E(3) (1)49470Q01184(2)E(3) (1)49470Q01224(2)E(3) (1)49470Q01274(2)E(3) (1)49470Q01334(2)E(3) (1)49470Q01394(2)E(3) (1)49470Q01474(2)E(3) (1)49470Q01564(2)E(3) (1)49470Q01684(2)E(3) (1)49470Q01824(2)E(3) (1)49470Q01105(2)E(3) (1)49470Q01125(2)E(3) (1)49470Q01155(2)E(3) (1)49470Q01185(2)E(3) (1)49470Q01225(2)E(3) (1)49470Q01275(2)E(3) (1)49470Q01335(2)E(3) (1)49470Q01395(2)E(3) (1)49470Q01475(2)E(3) (1)49470Q01565(2)E(3) 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1Q(3)50C154(2)(4)12 L1Q(3)50C184(2)(4)24 L1Q(3)50C224(2)(4)24 L1Q(3)50C274(2)(4)24 L1Q(3)50C334(2)(4)36 L1Q(3)50C394(2)(4)36 L1Q(3)50C474(2)(4)36 L1Q(3)50C564(2)(4)48 L1Q(3)50C684(2)(4)65 L1Q(3)40C824(2)(4)36 L1Q(3)40C105(2)(4)36 L1Q(3)40C125(2)(4)36 L1Q(3)40C155(2)(4)48 L1Q(3)40C185(2)(4)65 L1Q(3)30C225(2)(4)24 L1Q(3)30C275(2)(4)36 L1Q(3)30C335(2)(4)36 L1Q(3)30C395(2)(4)36 L1Q(3)30C475(2)(4)48 L1Q(3)30C565(2)(4)65 MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. KEMET P/N 1 500VDC - BQ Dielectric Complete P/N requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test level character "M" for B level, or "T" for T level (MIL-PRF-49470/1 part number only) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" (4) Test level character "B" for B level, or "T" for T level (KEMET part number only) 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 10 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1B - MIL-PRF-49470/2, Product Selection 50VDC-200VDC MIL-PRF-49470/2 Encapsulated, Horizontally Stacked MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) M49470X02125(1)A(2) M49470X02155(1)A(2) M49470X02185(1)A(2) M49470X02225(1)A(2) M49470X02275(1)A(2) M49470X02335(1)A(2) M49470X02475(1)A(2) M49470X02395(1)A(2) M49470X02565(1)A(2) M49470X02685(1)A(2) M49470X02825(1)A(2) M49470X02106(1)A(2) M49470X02126(1)A(2) M49470X02156(1)A(2) M49470X02186(1)A(2) M49470X02226(1)A(2) M49470X02276(1)A(2) M49470X02336(1)A(2) M49470X02396(1)A(2) M49470X02476(1)A(2) 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 M49470X02684(1)B(2) M49470X02824(1)B(2) M49470X02105(1)B(2) M49470X02125(1)B(2) M49470X02155(1)B(2) M49470X02185(1)B(2) M49470X02225(1)B(2) M49470X02275(1)B(2) M49470X02335(1)B(2) M49470X02395(1)B(2) M49470X02475(1)B(2) M49470X02565(1)B(2) M49470X02685(1)B(2) M49470X02825(1)B(2) M49470X02106(1)B(2) M49470X02126(1)B(2) M49470X02156(1)B(2) M49470X02186(1)B(2) M49470X02226(1)B(2) M49470X02276(1)B(2) 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 M49470R02474(1)C(2) M49470R02564(1)C(2) M49470R02684(1)C(2) M49470R02824(1)C(2) M49470R02105(1)C(2) M49470R02125(1)C(2) M49470R02155(1)C(2) M49470R02185(1)C(2) M49470R02225(1)C(2) 0.47 0.56 0.68 0.82 1 1.2 1.5 1.8 2.2 5 5 5 5 5 5 5 4 4 0.390 (9.91) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.660 (16.76) 0.800 (20.32) 0.530 (13.46) 0.530 (13.46) MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) Lead Config. KEMET P/N 1 N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L2X(2)505125(1)B27 L2X(2)505155(1)B39 L2X(2)505185(1)B39 L2X(2)505225(1)B39 L2X(2)505275(1)B53 L2X(2)505335(1)B53 L2X(2)505475(1)B66 L2X(2)505395(1)B66 L2X(2)505565(1)B80 L2X(2)405685(1)B53 L2X(2)405825(1)B53 L2X(2)405106(1)B66 L2X(2)405126(1)B66 L2X(2)405156(1)B80 L2X(2)305186(1)B39 L2X(2)305226(1)B53 L2X(2)305276(1)B53 L2X(2)305336(1)B53 L2X(2)305396(1)B66 L2X(2)305476(1)B80 N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L2X(2)501684(1)B27 L2X(2)501824(1)B39 L2X(2)501105(1)B39 L2X(2)501125(1)B39 L2X(2)501155(1)B53 L2X(2)501185(1)B53 L2X(2)501225(1)B66 L2X(2)501275(1)B66 L2X(2)501335(1)B80 L2X(2)401395(1)B53 L2X(2)401475(1)B53 L2X(2)401565(1)B66 L2X(2)401685(1)B66 L2X(2)401825(1)B80 L2X(2)301106(1)B39 L2X(2)301126(1)B39 L2X(2)301156(1)B53 L2X(2)301186(1)B53 L2X(2)301226(1)B66 L2X(2)301276(1)B80 K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L2R(2)502474(1)B39 L2R(2)502564(1)B39 L2R(2)502684(1)B53 L2R(2)502824(1)B53 L2R(2)502105(1)B66 L2R(2)502125(1)B66 L2R(2)502155(1)B80 L2R(2)402185(1)B53 L2R(2)402225(1)B53 Cap Tolerance Lead Config. KEMET P/N 1 Cap Tol. 50VDC - BX Dielectric 0.270 (6.86) 0.390 (9.91) 0.390 (9.91) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.660 (16.76) 0.800 (20.32) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.660 (16.76) 0.800 (20.32) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.800 (20.32) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M 100VDC - BX Dielectric 0.270 (6.86) 0.390 (9.91) 0.390 (9.91) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.660 (16.76) 0.800 (20.32) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.660 (16.76) 0.800 (20.32) 0.390 (9.91) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.800 (20.32) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M 200VDC - BR Dielectric Complete P/N requires additional characters in the numbered positions provided in order to indicate capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Capacitance tolerance character " K" or " M" (2) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 11 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1B - MIL-PRF-49470 /2, Product Selection 200VDC-500VDC con't MIL-PRF-49470/2 Encapsulated, Horizontally Stacked MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tol. Lead Config. KEMET P/N 1 M49470R02275(1)C(2) M49470R02335(1)C(2) M49470R02395(1)C(2) M49470R02475(1)C(2) M49470R02565(1)C(2) M49470R02685(1)C(2) M49470R02825(1)C(2) M49470R02106(1)C(2) M49470R02126(1)C(2) 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 4 4 4 3 3 3 3 3 3 0.660 (16.76) 0.660 (16.76) 0.800 (20.32) 0.390 (9.91) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.800 (20.32) K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L2R(2)402275(1)B66 L2R(2)402335(1)B66 L2R(2)402395(1)B80 L2R(2)302475(1)B39 L2R(2)302565(1)B39 L2R(2)302685(1)B53 L2R(2)302825(1)B53 L2R(2)302106(1)B66 L2R(2)302126(1)B80 M49470Q02154(1)E(2) M49470Q02184(1)E(2) M49470Q02224(1)E(2) M49470Q02274(1)E(2) M49470Q02334(1)E(2) M49470Q02394(1)E(2) M49470Q02474(1)E(2) M49470Q02564(1)E(2) M49470Q02684(1)E(2) M49470Q02824(1)E(2) M49470Q02105(1)E(2) M49470Q02125(1)E(2) M49470Q02155(1)E(2) M49470Q02185(1)E(2) M49470Q02225(1)E(2) M49470Q02275(1)E(2) M49470Q02335(1)E(2) M49470Q02395(1)E(2) M49470Q02475(1)E(2) M49470Q02565(1)E(2) M49470Q02565(1)E(2) 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 5.6 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 3 0.270 (6.86) 0.390 (9.91) 0.390 (9.91) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.800 (20.32) 0.530 (13.46) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.800 (20.32) 0.390 (9.91) 0.530 (13.46) 0.530 (13.46) 0.530 (13.46) 0.660 (16.76) 0.800 (20.32) 0.800 (20.32) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L2Q(2)50C154(1)B27 L2Q(2)50C184(1)B39 L2Q(2)50C224(1)B39 L2Q(2)50C274(1)B39 L2Q(2)50C334(1)B53 L2Q(2)50C394(1)B53 L2Q(2)50C474(1)B53 L2Q(2)50C564(1)B66 L2Q(2)50C684(1)B80 L2Q(2)40C824(1)B53 L2Q(2)40C105(1)B53 L2Q(2)40C125(1)B53 L2Q(2)40C155(1)B66 L2Q(2)40C185(1)B80 L2Q(2)30C225(1)B39 L2Q(2)30C275(1)B53 L2Q(2)30C335(1)B53 L2Q(2)30C395(1)B53 L2Q(2)30C475(1)B66 L2Q(2)30C565(1)B80 L2Q(2)30C565(1)B65 MIL-PRF-49470 P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. KEMET P/N 1 500VDC - BQ Dielectric Complete P/N requires additional characters in the numbered positions provided in order to indicate capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Capacitance tolerance character " K" or " M" (2) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 12 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Product Selection 25VDC Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) L1X(1)503824(2)(3)12 L1X(1)503105(2)(3)12 L1X(1)503125(2)(3)12 L1X(1)503155(2)(3)12 L1X(1)503185(2)(3)24 L1X(1)403225(2)(3)12 L1X(1)503225(2)(3)24 L1X(1)503255(2)(3)24 L1X(1)403275(2)(3)12 L1X(1)503275(2)(3)24 L1X(1)403335(2)(3)12 L1X(1)503335(2)(3)36 L1X(1)403395(2)(3)12 L1X(1)503395(2)(3)36 L1X(1)403475(2)(3)12 L1X(1)503475(2)(3)36 L1X(1)403565(2)(3)24 L1X(1)503565(2)(3)48 L1X(1)403605(2)(3)24 L1X(1)503605(2)(3)48 L1X(1)303685(2)(3)12 L1X(1)403685(2)(3)24 L1X(1)503685(2)(3)65 L1X(1)403755(2)(3)24 L1X(1)503755(2)(3)65 L1X(1)303825(2)(3)12 L1X(1)403825(2)(3)24 L1X(1)303106(2)(3)12 L1X(1)403106(2)(3)24 L1X(1)303116(2)(3)12 L1X(1)303126(2)(3)12 L1X(1)403126(2)(3)36 L1X(1)303156(2)(3)12 L1X(1)403156(2)(3)36 L1X(1)303166(2)(3)24 L1X(1)403166(2)(3)48 L1X(1)303186(2)(3)24 L1X(1)403186(2)(3)48 L1X(1)303206(2)(3)24 L1X(1)403206(2)(3)48 L1X(1)303226(2)(3)24 L1X(1)403226(2)(3)65 L1X(1)403246(2)(3)65 L1X(1)303276(2)(3)24 L1X(1)303306(2)(3)24 L1X(1)303306(2)(3)36 L1X(1)303336(2)(3)36 L1X(1)303396(2)(3)36 L1X(1)303456(2)(3)36 L1X(1)303506(2)(3)48 L1X(1)303546(2)(3)48 L1X(1)303606(2)(3)48 0.82 1 1.2 1.5 1.8 2.2 2.2 2.5 2.7 2.7 3.3 3.3 3.9 3.9 4.7 4.7 5.6 5.6 6 6 6.8 6.8 6.8 7.5 7.5 8.2 8.2 10 10 11 12 12 15 15 16 16 18 18 20 20 22 22 24 27 30 30 33 39 45 50 54 60 KEMET P/N 1 Cap (F) Height A inch (mm) Cap Tolerance Lead Config. 5 5 5 5 5 4 5 5 4 5 4 5 4 5 4 5 4 5 4 5 3 4 5 4 5 3 4 3 4 3 3 4 3 4 3 4 3 4 3 4 3 4 4 3 3 3 3 3 3 3 3 3 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.650 (16.51) 0.650 (16.51) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.480 (12.19) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K Case Code Height A inch (mm) Cap Tolerance Lead Config. Case Code 25VDC - BX Dielectric Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 13 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Commercial/Non-Standard - Product Selection 25VDC-50VDC con't. Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. L1X(1)303666(2)(3)65 L1X(1)303726(2)(3)65 L1X(1)303756(2)(3)65 66 72 75 3 3 3 0.650 (16.51) 0.650 (16.51) 0.650 (16.51) K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K L1X(1)505824(2)(3)12 L1X(1)505105(2)(3)12 L1X(1)505125(2)(3)12 L1X(1)505155(2)(3)12 L1X(1)505185(2)(3)24 L1X(1)405225(2)(3)12 L1X(1)505225(2)(3)24 L1X(1)505255(2)(3)24 L1X(1)405275(2)(3)12 L1X(1)505275(2)(3)24 L1X(1)505275(2)(3)36 L1X(1)405335(2)(3)12 L1X(1)505335(2)(3)36 L1X(1)405395(2)(3)12 L1X(1)505395(2)(3)36 L1X(1)405475(2)(3)12 L1X(1)505475(2)(3)36 L1X(1)405565(2)(3)24 L1X(1)505565(2)(3)48 L1X(1)405605(2)(3)24 L1X(1)505605(2)(3)48 L1X(1)305685(2)(3)12 L1X(1)405685(2)(3)24 L1X(1)505685(2)(3)65 L1X(1)405755(2)(3)24 L1X(1)505755(2)(3)65 L1X(1)305825(2)(3)12 L1X(1)405825(2)(3)24 L1X(1)305106(2)(3)12 L1X(1)405106(2)(3)24 L1X(1)305116(2)(3)12 L1X(1)305126(2)(3)12 L1X(1)405126(2)(3)36 L1X(1)305156(2)(3)12 L1X(1)405156(2)(3)36 L1X(1)305166(2)(3)24 L1X(1)405166(2)(3)48 L1X(1)305186(2)(3)24 L1X(1)405186(2)(3)48 L1X(1)305206(2)(3)24 L1X(1)405206(2)(3)48 L1X(1)305226(2)(3)24 L1X(1)405226(2)(3)65 L1X(1)405246(2)(3)65 L1X(1)305276(2)(3)24 L1X(1)305306(2)(3)24 L1X(1)305336(2)(3)36 L1X(1)305396(2)(3)36 L1X(1)305456(2)(3)36 0.82 1 1.2 1.5 1.8 2.2 2.2 2.5 2.7 2.7 2.7 3.3 3.3 3.9 3.9 4.7 4.7 5.6 5.6 6 6 6.8 6.8 6.8 7.5 7.5 8.2 8.2 10 10 11 12 12 15 15 16 16 18 18 20 20 22 22 24 27 30 33 39 45 5 5 5 5 5 4 5 5 4 5 5 4 5 4 5 4 5 4 5 4 5 3 4 5 4 5 3 4 3 4 3 3 4 3 4 3 4 3 4 3 4 3 4 4 3 3 3 3 3 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.650 (16.51) 0.650 (16.51) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. 50VDC - BX Dielectric Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 14 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Commercial/Non-Standard - Product Selection 50VDC-100VDC con't. Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. L1X(1)305506(2)(3)48 L1X(1)305546(2)(3)48 L1X(1)305606(2)(3)48 L1X(1)305666(2)(3)65 L1X(1)305726(2)(3)65 L1X(1)305756(2)(3)65 50 54 60 66 72 75 3 3 3 3 3 3 0.480 (12.19) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.650 (16.51) 0.650 (16.51) K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1R(1)501564(2)(3)12 L1R(1)501684(2)(3)12 L1R(1)501754(2)(3)12 L1R(1)501824(2)(3)12 L1R(1)501105(2)(3)12 L1R(1)501125(2)(3)12 L1R(1)401155(2)(3)12 L1R(1)501155(2)(3)24 L1R(1)401185(2)(3)12 L1R(1)501185(2)(3)24 L1R(1)401225(2)(3)12 L1R(1)501225(2)(3)24 L1R(1)501255(2)(3)24 L1R(1)401275(2)(3)12 L1R(1)501275(2)(3)36 L1R(1)401335(2)(3)12 L1R(1)501335(2)(3)36 L1R(1)401395(2)(3)12 L1R(1)501395(2)(3)48 L1R(1)401475(2)(3)24 L1R(1)501475(2)(3)48 L1R(1)301565(2)(3)12 L1R(1)401565(2)(3)24 L1R(1)501565(2)(3)65 L1R(1)301605(2)(3)12 L1R(1)401605(2)(3)24 L1R(1)501605(2)(3)65 L1R(1)301685(2)(3)12 L1R(1)401685(2)(3)24 L1R(1)401755(2)(3)24 L1R(1)301825(2)(3)12 L1R(1)401825(2)(3)36 L1R(1)301106(2)(3)12 L1R(1)401106(2)(3)36 L1R(1)301116(2)(3)12 L1R(1)301126(2)(3)24 L1R(1)401126(2)(3)48 L1R(1)301156(2)(3)24 L1R(1)401156(2)(3)48 L1R(1)301166(2)(3)24 L1R(1)401166(2)(3)65 L1R(1)301186(2)(3)24 L1R(1)401186(2)(3)65 L1R(1)301206(2)(3)24 L1R(1)301226(2)(3)36 L1R(1)301276(2)(3)36 0.56 0.68 0.75 0.82 1 1.2 1.5 1.5 1.8 1.8 2.2 2.2 2.5 2.7 2.7 3.3 3.3 3.9 3.9 4.7 4.7 5.6 5.6 5.6 6 6 6 6.8 6.8 7.5 8.2 8.2 10 10 11 12 12 15 15 16 16 18 18 20 22 27 5 5 5 5 5 5 4 5 4 5 4 5 5 4 5 4 5 4 5 4 5 3 4 5 3 4 5 3 4 4 3 4 3 4 3 3 4 3 4 3 4 3 4 3 3 3 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. 100VDC - BR Dielectric Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 15 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Commercial/Non-Standard - Product Selection 100VDC-200VDC con't. Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. L1R(1)301306(2)(3)36 L1R(1)301336(2)(3)48 L1R(1)301396(2)(3)48 L1R(1)301456(2)(3)65 L1R(1)301506(2)(3)65 30 33 39 45 50 3 3 3 3 3 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) 0.650 (16.51) K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1Q(1)502334(2)(3)12 L1Q(1)502394(2)(3)12 L1Q(1)502474(2)(3)12 L1Q(1)502564(2)(3)12 L1Q(1)502684(2)(3)12 L1Q(1)502754(2)(3)12 L1Q(1)402824(2)(3)12 L1Q(1)502824(2)(3)24 L1Q(1)402105(2)(3)12 L1Q(1)502105(2)(3)24 L1Q(1)402125(2)(3)12 L1Q(1)502125(2)(3)24 L1Q(1)402155(2)(3)12 L1Q(1)502155(2)(3)36 L1Q(1)402185(2)(3)12 L1Q(1)502185(2)(3)36 L1Q(1)402225(2)(3)24 L1Q(1)502225(2)(3)48 L1Q(1)302245(2)(3)12 L1Q(1)502255(2)(3)48 L1Q(1)302275(2)(3)12 L1Q(1)402275(2)(3)24 L1Q(1)502275(2)(3)48 L1Q(1)302335(2)(3)12 L1Q(1)402335(2)(3)24 L1Q(1)502335(2)(3)65 L1Q(1)302365(2)(3)12 L1Q(1)302395(2)(3)12 L1Q(1)402395(2)(3)24 L1Q(1)302475(2)(3)12 L1Q(1)402475(2)(3)36 L1Q(1)302565(2)(3)12 L1Q(1)402565(2)(3)36 L1Q(1)302605(2)(3)12 L1Q(1)402605(2)(3)36 L1Q(1)302685(2)(3)24 L1Q(1)402685(2)(3)48 L1Q(1)402755(2)(3)48 L1Q(1)302825(2)(3)24 L1Q(1)402825(2)(3)65 L1Q(1)302106(2)(3)24 L1Q(1)402106(2)(3)65 L1Q(1)302116(2)(3)24 L1Q(1)302126(2)(3)36 L1Q(1)302156(2)(3)36 L1Q(1)302166(2)(3)36 L1Q(1)302186(2)(3)48 0.33 0.39 0.47 0.56 0.68 0.75 0.82 0.82 1 1 1.2 1.2 1.5 1.5 1.8 1.8 2.2 2.2 2.4 2.5 2.7 2.7 2.7 3.3 3.3 3.3 3.6 3.9 3.9 4.7 4.7 5.6 5.6 6 6 6.8 6.8 7.5 8.2 8.2 10 10 11 12 15 16 18 5 5 5 5 5 5 4 5 4 5 4 5 4 5 4 5 4 5 3 5 3 4 5 3 4 5 3 3 4 3 4 3 4 3 4 3 4 4 3 4 3 4 3 3 3 3 3 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.240 (6.10) 0.480 (12.19) 0.120 (3.05) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.240 (6.10) 0.480 (12.19) 0.480 (12.19) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. 200VDC - BQ Dielectric Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 16 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Commercial/Non-Standard - Product Selection 200VDC-630VDC con't. Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. L1Q(1)302206(2)(3)48 L1Q(1)302226(2)(3)48 L1Q(1)302276(2)(3)65 20 22 27 3 3 3 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K L1W(1)50C124(2)(3)12 L1W(1)50C154(2)(3)12 L1W(1)50C184(2)(3)12 L1W(1)50C224(2)(3)12 L1W(1)50C274(2)(3)12 L1W(1)50C334(2)(3)24 L1W(1)40C394(2)(3)12 L1W(1)50C394(2)(3)24 L1W(1)40C474(2)(3)12 L1W(1)50C474(2)(3)24 L1W(1)50C564(2)(3)24 L1W(1)40C684(2)(3)12 L1W(1)50C684(2)(3)36 L1W(1)50C754(2)(3)36 L1W(1)40C824(2)(3)12 L1W(1)50C824(2)(3)36 L1W(1)30C105(2)(3)12 L1W(1)40C105(2)(3)24 L1W(1)50C105(2)(3)48 L1W(1)30C125(2)(3)12 L1W(1)40C125(2)(3)24 L1W(1)50C125(2)(3)65 L1W(1)30C155(2)(3)12 L1W(1)40C155(2)(3)24 L1W(1)50C155(2)(3)65 L1W(1)40C185(2)(3)36 L1W(1)30C225(2)(3)12 L1W(1)40C225(2)(3)36 L1W(1)30C245(2)(3)12 L1W(1)30C275(2)(3)12 L1W(1)40C275(2)(3)48 L1W(1)30C335(2)(3)24 L1W(1)40C335(2)(3)48 L1W(1)30C365(2)(3)24 L1W(1)30C395(2)(3)24 L1W(1)40C395(2)(3)65 L1W(1)30C475(2)(3)24 L1W(1)30C565(2)(3)24 L1W(1)30C605(2)(3)24 L1W(1)30C685(2)(3)36 L1W(1)30C825(2)(3)36 L1W(1)30C106(2)(3)48 L1W(1)30C116(2)(3)65 L1W(1)30C126(2)(3)65 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.39 0.47 0.47 0.56 0.68 0.68 0.75 0.82 0.82 1 1 1 1.2 1.2 1.2 1.5 1.5 1.5 1.8 2.2 2.2 2.4 2.7 2.7 3.3 3.3 3.6 3.9 3.9 4.7 5.6 6 6.8 8.2 10 11 12 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.240 (6.10) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.120 (3.05) 0.480 (12.19) 0.240 (6.10) 0.480 (12.19) 0.240 (6.10) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1W(1)50B683(2)(3)12 L1W(1)40B104(2)(3)12 L1W(1)50B104(2)(3)12 0.068 0.1 0.1 5 4 5 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. 500VDC - X7R Dielectric 5 5 5 5 5 5 4 5 4 5 5 4 5 5 4 5 3 4 5 3 4 5 3 4 5 4 3 4 3 3 4 3 4 3 3 4 3 3 3 3 3 3 3 3 630VDC - X7R Dielectric Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 17 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Commercial/Non-Standard - Product Selection 630VDC-1000VDC con't. Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. L1W(1)50B124(2)(3)12 L1W(1)50B154(2)(3)12 L1W(1)50B184(2)(3)24 L1W(1)30B224(2)(3)12 L1W(1)40B224(2)(3)12 L1W(1)50B224(2)(3)24 L1W(1)50B274(2)(3)24 L1W(1)30B334(2)(3)12 L1W(1)50B334(2)(3)36 L1W(1)40B394(2)(3)12 L1W(1)50B394(2)(3)36 L1W(1)30B474(2)(3)12 L1W(1)40B474(2)(3)24 L1W(1)50B474(2)(3)36 L1W(1)50B564(2)(3)48 L1W(1)30B684(2)(3)12 L1W(1)40B684(2)(3)24 L1W(1)50B684(2)(3)65 L1W(1)50B754(2)(3)65 L1W(1)40B824(2)(3)24 L1W(1)30B105(2)(3)12 L1W(1)40B105(2)(3)36 L1W(1)30B125(2)(3)12 L1W(1)40B125(2)(3)36 L1W(1)30B155(2)(3)12 L1W(1)40B155(2)(3)48 L1W(1)40B185(2)(3)48 L1W(1)30B225(2)(3)24 L1W(1)40B225(2)(3)65 L1W(1)30B245(2)(3)24 L1W(1)30B275(2)(3)24 L1W(1)30B335(2)(3)36 L1W(1)30B365(2)(3)36 L1W(1)30B395(2)(3)36 L1W(1)30B475(2)(3)36 L1W(1)30B565(2)(3)48 L1W(1)30B605(2)(3)65 L1W(1)30B685(2)(3)65 0.12 0.15 0.18 0.22 0.22 0.22 0.27 0.33 0.33 0.39 0.39 0.47 0.47 0.47 0.56 0.68 0.68 0.68 0.75 0.82 1 1 1.2 1.2 1.5 1.5 1.8 2.2 2.2 2.4 2.7 3.3 3.6 3.9 4.7 5.6 6 6.8 5 5 5 3 4 5 5 3 5 4 5 3 4 5 5 3 4 5 5 4 3 4 3 4 3 4 4 3 4 3 3 3 3 3 3 3 3 3 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.240 (6.10) 0.360 (9.14) 0.480 (12.19) 0.120 (3.05) 0.240 (6.10) 0.650 (16.51) 0.650 (16.51) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.360 (9.14) 0.120 (3.05) 0.480 (12.19) 0.480 (12.19) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.650 (16.51) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K L1W(1)50D473(2)(3)12 L1W(1)50D683(2)(3)12 L1W(1)30D104(2)(3)12 L1W(1)40D104(2)(3)12 L1W(1)50D104(2)(3)24 L1W(1)50D124(2)(3)24 L1W(1)50D154(2)(3)36 L1W(1)50D184(2)(3)36 L1W(1)30D224(2)(3)12 L1W(1)40D224(2)(3)12 L1W(1)50D224(2)(3)36 L1W(1)50D274(2)(3)48 L1W(1)30D334(2)(3)12 L1W(1)50D334(2)(3)65 0.047 0.068 0.1 0.1 0.1 0.12 0.15 0.18 0.22 0.22 0.22 0.27 0.33 0.33 5 5 3 4 5 5 5 5 3 4 5 5 3 5 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.240 (6.10) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.120 (3.05) 0.120 (3.05) 0.360 (9.14) 0.480 (12.19) 0.120 (3.05) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. 1000VDC - X7R Dielectric Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 18 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 1C - Commercial/Non-Standard - Product Selection 1000VDC con't. Commercial/Non-Standard - Customer Specific Unencapsulated, Horizontally Stacked KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. L1W(1)40D394(2)(3)24 L1W(1)50D394(2)(3)65 L1W(1)30D474(2)(3)12 L1W(1)40D474(2)(3)24 L1W(1)30D684(2)(3)12 L1W(1)40D684(2)(3)36 L1W(1)40D824(2)(3)48 L1W(1)30D105(2)(3)24 L1W(1)40D105(2)(3)65 L1W(1)30D125(2)(3)24 L1W(1)30D155(2)(3)36 L1W(1)30D225(2)(3)36 L1W(1)30D245(2)(3)48 L1W(1)30D275(2)(3)48 L1W(1)30D335(2)(3)65 0.39 0.39 0.47 0.47 0.68 0.68 0.82 1 1 1.2 1.5 2.2 2.4 2.7 3.3 4 5 3 4 3 4 4 3 4 3 3 3 3 3 3 0.240 (6.10) 0.650 (16.51) 0.120 (3.05) 0.240 (6.10) 0.120 (3.05) 0.360 (9.14) 0.480 (12.19) 0.240 (6.10) 0.650 (16.51) 0.240 (6.10) 0.360 (9.14) 0.360 (9.14) 0.480 (12.19) 0.480 (12.19) 0.650 (16.51) K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K N, L, M, J, K KEMET P/N 1 Cap (F) Case Code Height A inch (mm) Cap Tolerance Lead Config. Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and lead configuration. For each numbered position, available options are as follows: (1) Test Level character "S" for Commercial, or "X" for non-standard (customer specific) (2) Capacitance tolerance character " K" or " M" (3) Lead style character " N", "L", "M", "J" or "K" 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 19 Roll Over for Order Info. Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Soldering Process The capacitors and assemblies outlined in this specification sheet are susceptible to thermal shock damage due to their large ceramic mass. Temperature profiles used should provide adequate temperature rise and cool-down time to prevent damage from thermal shock. In general, KEMET recommends against hand soldering for these types of large ceramic devices. Recommended Soldering Technique: * Solder reflow only Recommended Reflow Soldering Profile: Temperature TP TL tP Max Ramp Up Rate = 2 C/sec Max Ramp Down Rate = 2 C/sec tL Tsmax Tsmin 25 tS 25 C to Peak Time Profile Feature Sn-Pb Assembly Preheat/Soak Temperature Min (TSmin) Temperature Max (TSmax) Time (ts) from Tsmin to Tsmax) Ramp-up rate (TL to TP) Liquidous temperature (TL) Time above liquidous (tL) Peak Temperature (TP) 100C 150C 60-90 sec 2C/sec 183C 95 sec 240C Time within 5 C of max peak temperature (tP) 5 sec Ramp-down rate (TP to TL) Time 25 C to peak temperature 2C/sec 3.5 minutes Note 1: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow Preheating and Reflow Profile Notes: Due to differences in the coefficient of thermal expansion for the different materials of construction, it is critical to monitor and control the heating and cooling rates during the soldering process. During the reflow soldering process, the maximum recommended heating and cooling rate (dT/dt) is 4C/second. To ensure optimal component reliability, KEMET's recommended heating and cooling rate is 2C/second. After soldering, the capacitors should be air cooled to room temperature before further processing. Forced air cooling is not recommended. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 20 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Table 4 - Performance & Reliability: Test Methods and Conditions Inspection Test Method Test Level Option MIL-PRF-49470 B Level (B) MIL-PRF-49470 T Level (T) DSSC Drawing 87106 (C)1 Commercial (S) Non-Standard (X)2 Not required Not required Optional per Source Controlled Drawing (SCD) In-Process Inspection Ultrasonic Scanning (C-SAM) DPA Analysis In-Process Visual Inspection Meet EIA-469 Criteria EIA-469 Not required Yes (per lot) MIL-PRF-49470 Method 4.8.3 Group A Requirements MIL-STD-202 Method 107 Yes (5 cycles) Voltage Conditioning 200V 500V MIL-PRF-49470 Method 4.8.5.2 200%Vr @125C 120%Vr @125C Yes (96 hrs min.) Visual and Mechanical Inspection MIL-PRF-49470 Method 4.8.4 Yes (per lot) Solderability MIL-STD-202 Method 208 Yes (per Inspection lot) DPA Analysis EIA-469 Not required Thermal Shock Yes (20 cycles) Yes (168 hrs min.) Yes (5 cycles) Yes (96 hrs min.) Yes (per lot) Yes (per lot) Optional per Source Controlled Drawing (SCD) Not required Yes (per inspection lot) Yes (per lot) Optional per Source Controlled Drawing (SCD) Not required Group B Requirements Voltage-Temperature Limits (TCVC) Resistance to Solvents Terminal Strength Resistance to Soldering Heat Moisture Resistance Marking Legibility Low Voltage Humidity Testing Life Test 200V 500V Thermal Shock MIL-PRF-49470 Method 4.8.13.2 MIL-STD-202 Method 215 MIL-STD-202 Method 211 MIL-STD-202 Method 210 MIL-STD-202 Method 106 MIL-PRF-49470 Method 4.8.4.1 MIL-STD-202 Method 103 MIL-STD-202 Method 108 200%Vr @125C 120%Vr @125C MIL-STD-202 Method 107 Yes (periodic) Yes (periodic) Yes (per lot) Not required Not required Yes (periodic) Yes (periodic) Not required Not required Not required Optional per Source Controlled Drawing (SCD) Yes Yes KEMET Requirements Visual and Mechanical Inspection (100%) KEMET Standard Yes Yes Yes Voltage Conditioning As per discretionary statement outlined in cancelled DSCC Drawing 87106, KEMET will not perform Group B inspections on a per lot basis. KEMET 87106 orders may include a standard certificate of compliance stating compliance to the 87106 requirements, specifically conformance to Group B inspections. Please contact KEMET for additional details 2 Non-standard test level option is designated to satisfy customer specific testing requirements that may deviate from those stated in a Mil-Spec or DSCC drawing. 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 21 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Product Marking Capacitors shall be marked with KEMET's name, trademark or (CAGE) code, date, capacitance and capacitance tolerance codes. The date code shall consist of the year and week. For example, the third week of 2011 would be 1103 using a 4-digit date code or 103 using a 3-digit date code. At the option of the JT manufacturer, the date code may be placed on a separate line. Full marking shall be included 12345 on the package. 106K 1103 MIL-PRF-49470 Capacitor marking will include "JAN" or "J." Case code 4 or 5 example Case codes 4 and 5 shall be marked with the following sequence of information: J brand (1 digit), product level designator ("B" or "T") Manufacturer's identification (1 to 5 digits) Capacitance code (3 digits) and capacitance tolerance (1 digit) Date code (3 or 4 digits) Case code 3 shall either be fully marked or partially marked like case code 4 or 5 parts at the option of KEMET. DSCC 87106 Marking shall be in accordance with MIL-STD-1285, except the parts shall be marked with the part number as specified in paragraph 1.2 of DSCC Drawing 87106 with the manufacturer's name or code and date code minimum. Case sizes 4 and 5 shall be marked with coded capacitance and tolerance minimum. Full marking shall be included on the package. Storage and Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature - reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40 degrees C, and maximum storage humidity not exceed 70% relative humidity. In addition, temperature fluctuations should be minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be used promptly, preferably within 1.5 years of receipt. Packaging Shipping Container Packaging Quantities 1 Case Code Small Box Quantity1 (7.5" x 7.5") Large Box Quantity1 (13.0" x 13.0" ) 3 4 5 28 36 64 104 144 225 Minimum order value applies. Contact KEMET for details. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 22 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Application Notes Notice of KEMET MIL-PRF-49470 Qualified Products Listing (QPL) Status. KEMET is qualified to supply MIL-PRF-49470/1 unencapsulated X7R Case Codes 3, 4, & 5 ceramic SMPS capacitors in DC voltage ratings of 50V, 100V, 200V, and 500V. This qualification includes both "B" and "T" test levels. KEMET is also qualified to supply MIL-PRF-49470/2 encapsulated X7R Case Codes 3, 4, & 5 ceramic SMPS capacitors in DC voltage ratings of 50V, 100V, 200V, and 500V. This qualification includes "B" level testing only. Notice of Cancellation: DSCC Drawing 87106 was cancelled on January 3rd 2005. MIL-PRF-49470 parts are preferred and direct replacements. MIL-PRF-49470 capacitors are preferred over DSCC 87106 capacitors. The MIL-PRF-49470 specification was developed as part of a cooperative effort between the U.S. Military, NASA and the switch mode power supply capacitor manufacturers to produce a robust direct replacement for the DSCC drawing. The military specification product provides additional quality assurance provisions that are NOT required by the DSCC drawing. Two product levels are offered in MILPRF-49470: the standard "B" level and the high reliability "T" level. Some of the benefits of the MIL-PRF-49470 product over the 87106 product include the following: Formal qualification process (QPL established), MIL-STD-790 compliance, DSCC audits, routine qualification maintenance testing, i.e., life testing, group A percent defective allowed (PDA) specified, and prohibiting the mixing of chips from different production lots within a single SMPS capacitor stack lot. MIL-PRF-49470 "T" Level product is recommended for all high reliability applications. MIL-PRF-49470 "T" level product requires the following in-process inspections and additional group A and B screening inspections that are not part of the normal "B" level flow: In-process screening that includes non-destructive internal examination (chip level) and destructive physical analysis (chip level), group A destructive physical analysis (finished stack level), group B lot specific humidity, steady-state, low voltage (lot sample test), and group B lot specific thermal shock & life test (lot sample test). For additional information regarding KEMET MIL-PRF-49470 QPL status or cancellation of DSCC Drawing 87106, please visit the DSCC website at: www.dscc.dla.mil. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 23 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors KEMET Corporation World Headquarters Europe Asia 2835 KEMET Way Simpsonville, SC 29681 Southern Europe Geneva, Switzerland Tel: 41-22-715-0100 Northeast Asia Paris, France Tel: 33-1-4646-1009 Shenzhen, China Tel: 86-755-2518-1306 Sasso Marconi, Italy Tel: 39-051-939111 Beijing, China Tel: 86-10-5829-1711 Milan, Italy Tel: 39-02-57518176 Shanghai, China Tel: 86-21-6447-0707 Fort Lauderdale, FL Tel: 954-766-2800 Rome, Italy Tel: 39-06-23231718 Taipei, Taiwan Tel: 886-2-27528585 North America Madrid, Spain Tel: 34-91-804-4303 Southeast Asia Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Corporate Offices Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 West Chester, PA Tel: 610-692-4642 Central Europe Hong Kong Tel: 852-2305-1168 Singapore Tel: 65-6586-1900 Landsberg, Germany Tel: 49-8191-3350800 Penang, Malaysia Tel: 60-4-6430200 Dortmund, Germany Tel: 49-2307-3619672 Bangalore, India Tel: 91-806-53-76817 Kwidzyn, Poland Tel: 48-55-279-7025 Central Schaumburg, IL Tel: 847-882-3590 Carmel, IN Tel: 317-706-6742 West Milpitas, CA Tel: 408-433-9950 Mexico Zapopan, Jalisco Tel: 52-33-3123-2141 Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-757201 Weymouth, United Kingdom Tel: 44-1305-830747 Coatbridge, Scotland Tel: 44-1236-434455 Farjestaden, Sweden Tel: 46-485-563934 Espoo, Finland Tel: 358-9-5406-5000 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 24 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 25 Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors -KPS MIL Series, SMPS Stacked Capacitors Digitally signed by Marcy Brand DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand, email=marcybrand@kemet.com Date: 2011.08.12 15:07:08 -04'00' (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.comC1031_KPS_SMPS_49470_STACKS * 8/10/2011 26