L2XJ301186KB53 - KEMET Electronics Corporation

One WORLD One Brand One Strategy One Focus One Team One KEMET

Benets

• -55°C to +125°C operating temperature range

• High frequency performance

• Bulk capacitance in a reduced footprint

• MIL-PRF-49470 QPL

• Military Case Codes 3, 4 and 5

• Space Grade available (“T” Level)

• DSCC approved (87106)

• Commercial/Industrial Grade available

• Customer specic requirements available

• Low ESR and ESL

• High thermal stability

• High ripple current capability

• Higher reliability than aluminum electrolytic or tantalum

• Available encapsulated or unencapsulated

Applications

• Military

• Space

• Industrial

• Input and output ltering on power supplies – often found on

“capacitor banks“

• Snubber circuits

• Radar ltering (28V/microwave burst)

Overview

KEMET Power Solutions (KPS) MIL Series ceramic stacked

capacitors are available in commercial, military and space grades

and are well suited for standard and high reliability switch mode

power supply (SMPS) and pulse energy applications. Qualied

under performance specication MIL-PRF-49470, our military and

space grade products meet or exceed the requirements outlined

by DSCC (Defense Supply Center, Columbus) and are available

in both B (standard reliability) & T (high reliability) product levels.

MIL-PRF-49470 was developed as part of a cooperative effort

between the U.S. Military, NASA and SMPS suppliers to produce

a robust replacement to cancelled DSCC Drawing 87106.

The KPS MIL Series is constructed using large chip multilayer

ceramic capacitors (MLCCs), horizontally stacked and secured

to a lead-frame termination system using a high melting point

(HMP) solder alloy. The lead frame isolates the MLCCs from the

printed circuit board (PCB) while establishing a parallel circuit

conguration. Mechanically isolating the capacitors from the PCB

improves mechanical and thermal stress performance, while the

parallel circuit conguration allows for bulk capacitance in the

same or smaller design footprint.

Available in BX, BR, BQ, and X7R dielectrics, these devices

are available in encapsulated and unencapsulated styles

in both surface mountable and through-hole congurations.

Their low Equivalent Series Resistance (ESR) and Equivalent

Series Inductance (ESL) make them ideally suited for input and

output ltering of power supply as well as snubber applications.

The encapsulated styles are primarily used where increased

mechanical and environmental protection is required, such as in

avionics systems.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors

KPS MIL Series, SMPS Stacked Capacitors, MIL-PRF-49470,

DSCC 87106, 50VDC–500VDC (Commercial, Military, & Space Grades)

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

MIL-PRF-49470 Ordering Information

M49470 R01 474 KCN

Performance Specication

Indicating MIL-PRF-494701

Dielectric Classication/

Characteristic2

Performance Specication Sheet

Number (Indicating MIL-PRF-49470/1)3Capacitance

Code (pF)

Capacitance

Tolerance Rated

Voltage (DC)

Lead

Conguration4

M49470 = B level

T49470 = T level

A “T” prex is used in place

of the “M” for T level product.

Q = BQ

R = BR

X = BX

01 = Unencapsulated

02 = Encapsulated

2 Sig. Digits

+ Number of

Zeros

J = ±5%

K = ±10%

M = ±20%

A = 50V

B = 100V

C = 200V

E = 500V

N = Straight Pin

L = Formed "L"

M= Formed "L"

J= Formed "J"

K= Formed "J"

1 Indicates performance and reliability requirements. "B" level represents standard reliability."T" level represents high reliability.

1 Please refer to performance specication sheet MIL-PRF-49470 for details regarding test levels. The latest revision of the specication sheet is available through DSCC.

1, 3 Test level option "T" is not available on encapsulated stacked devices (i.e. MIL-PRF-49470/2).

2 Dielectric classication and characteristic details are outlined in the "Electrical Parameters" section of this document.

4 Lead conguration and dimension details are outlined in the "Dimensions" section of this document.

KPS MIL Series, SMPS Stacks Ordering Information

(Do not use this ordering code if a QPL MIL-SPEC part type is required. Please order using MIL-SPEC ordering code. Details

regarding MIL-PRF-49470 QPL ordering information is outlined above.)

L1 R N 30 C 106 K S 12

Product Family1

Dielectric

Classication/

Characteristic2

Lead

Conguration3

Case Size /

Case Code

(CC)

Rated

Voltage (DC)

Capacitance

Code (pF)

Capacitance

Tolerance Testing Option4Maximum Height

Dimension (in.)5

L1 =

Unencapsulated

L2 =

Encapsulated

Q = BQ

R = BR

X = BX

W = X7R

N = Straight

L = Formed "L"

M= Formed "L"

J= Formed "J"

K= Formed "J"

30 = CC 3

40 = CC 4

50 = CC 5

3 = 25V

5 = 50V

1 = 100V

2 = 200V

C = 500V

B = 630V

D = 1000V

2 Sig. Digits

+ Number of

Zeros

J = ±5%

K = ±10%

M = ±20%

B = M49470 "B" Level

T = M49470 "T" Level

C = DSCC87106

S = Commercial

X = Non-Standard

(Customer Specic

Requirements)

Unencapsulated

12 = 0.12"

24 = 0.24"

36 = 0.36"

48 = 0.48"

65 = 0.65"

Encapsulated

27 = 0.27"

39 = 0.39"

53 = 0.53"

66 = 0.66"

80 = 0.80"

1, 4 Test level option "T" is not available on encapsulated stacked devices, i.e., MIL-PRF-49470/2. If a QPL MIL-Spec part type is required, please order using the

MIL-Spec ordering code.

2 Dielectric classication and characteristic details are outlined in the ""Electrical Parameters"" section of this document.

3 Lead conguration and dimension details are outlined in the "Dimensions" section of this document. Additional lead congurations may be available. Contact

KEMET for details.

4 Indicates performance and reliability requirements. Testing option details are outlined in the "Performance and Reliability" section of this document.

4 Please refer to performance specication sheet MIL-PRF-49470 for additional details regarding test levels. The latest revision of the specication sheet is

available through DSCC.

4 DSCC Drawing 87106 was cancelled on 01/03/2005. MIL-PRF-49470 capacitors are preferred over DSCC Drawing 87106 capacitors.

5 Maximum height dimensions are provided in product tables 1A, 1B, and 1C of this document

Ordering Information Requirements per DSCC Drawing 87106

DSCC Drawing 87106 was cancelled on 01/03/2005. Customers can continue to order per 87106 requirements using the original DSCC ordering code,i.e., 87106-001.

When available, MIL-PRF-49470 devices are preferred over DSCC Drawing 87106. The MIL-PRF-49470 military specication product provides additional quality

assurance provisions that are not required by the DSCC drawing. These extra provisions create a more robust replacement.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Construction

Note: Image is exaggerated in order to clearly identify all components of construction

Reference Item Material

ALeadframe Phosphor Bronze - Alloy 510

B Leadframe Attach Solder Sn10, Pb88, Ag2

Termination System1

SnPb (4% min.)

Solderable SilverDNi

EAg

FElectrode PdAg

GDielectric BaTiO3

H Lead Solder Sn60, Pb40

JEncapsulation2Molding Compound

KDiallyl-Phthalate (DAP)

1 KEMET reserves the right to construct these devices using either of the termination systems outlined.

2 Encapsulated product only, i.e., MIL-PRF-49470/2 and L2 product families.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Unencapsulated (M49470/1 & L1) Product Dimensions – Inches (Millimeters)

Case

Code

Lead Spacing

±0.025 (0.635)

Length ±0.010

(0.250)

Width

Min.

Width

Max.

Height

Max.

Seating Plane1

±0.010 (0.250)

Number of

Leads per

Side

Mounting

Technique

3 0.450 (11.43) 0.500 (12.70) 0.950 (24.13) 1.075 (27.30) Refer to

tables 1A &

1C for specic

maximum A

dimension

0.055 (1.40)

Solder reow only

4 0.400 (10.16) 0.440 (11.18) 0.350 (8.89) 0.425 (10.80) 4

5 0.250 (6.35) 0.300 (7.62) 0.224 (5.69) 0.275 (6.98) 3

1 Only applies to lead style "N" (straight).

1. Unless otherwise specied, tolerances are ±.010" (0.25mm).

2. Metric equivalents for C, D and E dimensions are provided for general information only.

3. For maximum B dimension, add .065" (1.65mm) to the appropriate A dimension. For all lead styles, the number of chips is determined by the capacitance and

voltage rating.

4. For case code 5, dimensions shall be .100" (2.54mm) maximum and .012” (0.30mm) minimum.

5. Lead alignment within pin rows shall be within ±.005" (0.13mm).

Unencapsulated & Encapsulated Lead Congurations – Inches (Millimeters)

Lead Style

Symbol Lead Style L

Lead Length

N (N) Straight 0.250 Min. (6.35)

L (L) Formed 0.070 ± 0.010 (1.78 ± 0.25)

M0.045 ± 0.010 (1.14 ± 0.25)

J(J) Formed 0.070 ± 0.010 (1.78 ± 0.25)

K0.045 ± 0.010 (1.14 ± 0.25)

Additional lead congurations may be available. Contact KEMET for details.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Encapsulated (M49470/2 & L2) Product Dimensions – Inches (Millimeters)

Case Code

Lead Spacing

±0.025 (0.635)

Length Max.

Width ±0.635

(±0.025)

Height

Number of

Leads per

Side

Mounting

Technique

3 0.450 (11.43) 0.580 (14.73) 1.155 (29.34) Refer to table 1B for

specic maximum A

dimension

10 Solder reow only

4 0.400 (10.16) 0.485 (12.32) 0.485 (12.32) 4

5 0.250 (6.35) 0.355 (9.02) 0.355 (9.02) 3

1. Dimensions are in inches.

2. Metric equivalents are given for general information only.

3. Unless otherwise specied, tolerances are ±.010” (0.25mm).

4. Lead alignment within pin rows shall be within ±.005” (0.13mm).

Unencapsulated & Encapsulated Lead Congurations – Inches (Millimeters)

Lead Style

Symbol Lead Style L

Lead Length

N (N) Straight 0.250 Min. (6.35)

L(L) Formed 0.070 ± 0.010 (1.78 ± 0.25)

M0.045 ± 0.010 (1.14 ± 0.25)

J(J) Formed 0.070 ± 0.010 (1.78 ± 0.25)

K0.045 ± 0.010 (1.14 ± 0.25)

Additional lead congurations may be available. Contact KEMET for details.

SEE NOTE 4

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Qualication Inspection Per MIL-PRF-49470

Inspection Test Method Paragraph

Group I

Thermal shock and voltage conditioning 4.8.5

Group II

Visual and mechanical Inspection 4.8.4

Group III

Low temperature storage 4.8.23

Barometric pressure 4.8.9

Terminal strength 4.8.10

Group IV

Voltage-temperature limits 4.8.13.1

Vibration, high frequency 4.8.14

Immersion 4.8.15

Group V

Shock, specied pulse 4.8.16

Resistance to soldering heat 4.8.17

Moisture resistance 4.8.18

Group VI

DPA (T level only) 4.8.19

Group VII

Humidity, steady state, low voltage (T level only) 4.8.21

Group VIII

Life 4.8.22

Environmental Compliance

These devices do not meet RoHS criteria

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Electrical Parameters/Performance Characteristics: BQ Dielectric

Item Parameters/Characteristics

Operating Temperature Range -55°C to +125°C

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±15%

Capacitance Change with Reference to +25°C and 100% Rated VDC Applied +15%, -50%

Aging Rate (Max % Cap Loss/Decade Hour) 1%

Dielectric Withstanding Voltage

250% of rated DC voltage for voltage rating < 500V

150% of rated DC voltage for voltage rating of 500V

(5 ± 1 seconds and charge/discharge not exceeding 50mA)

Dissipation Factor (DF) Maximum Limit @ 25ºC 2.5%

Insulation Resistance (IR) Limit @ 25°C 1000 megohm microfarads (minimum) or 100GΩ

Insulation Resistance (IR) Limit @ 125°C 100 megohm microfarads (minimum) or 10GΩ

Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours.

To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.

Capacitance and Dissipation Factor (DF) measured under the following conditions:

1kHz ± 100Hz at 1.0Vrms ± 0.2 Vrms (open circuit voltage).

Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic

Level Control (ALC). The ALC feature should be switched to "ON."

Electrical Parameters/Performance Characteristics: BR Dielectric

Item Parameters/Characteristics

Operating Temperature Range -55°C to +125°C

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±15%

Capacitance Change with Reference to +25°C and 100% Rated VDC Applied +15%, -40%

Aging Rate (Max % Cap Loss/Decade Hour) 1%

Dielectric Withstanding Voltage

250% of rated DC voltage for voltage rating < 500V

150% of rated DC voltage for voltage rating of 500V

(5 ± 1 seconds and charge/discharge not exceeding 50mA)

Dissipation Factor (DF) Maximum Limit @ 25ºC 2.5%

Insulation Resistance (IR) Limit @ 25°C 1000 megohm microfarads (minimum) or 100GΩ

Insulation Resistance (IR) Limit @ 125°C 100 megohm microfarads (minimum) or 10GΩ

Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours.

To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.

Capacitance and Dissipation Factor (DF) measured under the following conditions:

1kHz ± 100Hz at 1.0Vrms ± 0.2 Vrms (open circuit voltage).

Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic

Level Control (ALC). The ALC feature should be switched to "ON."

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Electrical Parameters/Performance Characteristics: BX Dielectric

Item Parameters/Characteristics

Operating Temperature Range -55°C to +125°C

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±15%

Capacitance Change with Reference to +25°C and 100% Rated VDC Applied +15%, -25%

Aging Rate (Max % Cap Loss/Decade Hour) 1%

Dielectric Withstanding Voltage

250% of rated DC voltage for voltage rating < 500V

150% of rated DC voltage for voltage rating of 500V

(5 ± 1 seconds and charge/discharge not exceeding 50mA)

Dissipation Factor (DF) Maximum Limit @ 25ºC 2.5%

Insulation Resistance (IR) Limit @ 25°C 1000 megohm microfarads (minimum) or 100GΩ

Insulation Resistance (IR) Limit @ 125°C 100 megohm microfarads (minimum) or 10GΩ

Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours.

To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.

Capacitance and Dissipation Factor (DF) measured under the following conditions:

1kHz ± 100Hz at 1.0Vrms ± 0.2 Vrms (open circuit voltage).

Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic

Level Control (ALC). The ALC feature should be switched to "ON."

Electrical Parameters/Performance Characteristics: X7R Dielectric

Item Parameters/Characteristics

Operating Temperature Range -55°C to +125°C

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±15%

Aging Rate (Max % Cap Loss/Decade Hour) 3.0%

Dielectric Withstanding Voltage 250% of rated voltage

(5 ± 1 seconds and charge/discharge not exceeding 50mA)

Dissipation Factor (DF) Maximum Limit @ 25ºC 3.5% (25V) and 2.5% (50V to 200V)

Insulation Resistance (IR) Limit @ 25°C 1000 megohm microfarads or 100GΩ

(Rated voltage applied for 120 ± 5 secs @ 25°C)

Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1000 hours.

To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.

Capacitance and Dissipation Factor (DF) measured under the following conditions:

1kHz ± 50Hz and 1.0 ± 0.2 Vrms if capacitance ≤10µF.

20Hz ± 10Hz and 0.5 ± 0.1 Vrms if capacitance >10µF.

Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as Automatic

Level Control (ALC). The ALC feature should be switched to "ON."

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

MIL-PRF-49470/1 Unencapsulated, Horizontally Stacked

MIL-PRF-49470 P/N 1Cap (μF) Case

Code

Height A

inch (mm) Cap Tol. Lead

Cong. KEMET P/N 1

50VDC - BX Dielectric

(1)49470X01105(2)A(3) 1 5 0.120 (3.05) K, M N, L, M, J, K L1X(3)505105(2)(4)12

(1)49470X01125(2)A(3) 1.2 5 0.120 (3.05) K, M N, L, M, J, K L1X(3)505125(2)(4)12

(1)49470X01155(2)A(3) 1.5 5 0.240 (6.10) K, M N, L, M, J, K L1X(3)505155(2)(4)24

(1)49470X01185(2)A(3) 1.8 5 0.240 (6.10) K, M N, L, M, J, K L1X(3)505185(2)(4)24

(1)49470X01225(2)A(3) 2.2 5 0.240 (6.10) K, M N, L, M, J, K L1X(3)505225(2)(4)24

(1)49470X01275(2)A(3) 2.7 5 0.360 (9.14) K, M N, L, M, J, K L1X(3)505275(2)(4)36

(1)49470X01335(2)A(3) 3.3 5 0.360 (9.14) K, M N, L, M, J, K L1X(3)505335(2)(4)36

(1)49470X01475(2)A(3) 3.9 5 0.480 (12.19) K, M N, L, M, J, K L1X(3)505475(2)(4)48

(1)49470X01395(2)A(3) 3.9 5 0.480 (12.19) K, M N, L, M, J, K L1X(3)505395(2)(4)48

(1)49470X01565(2)A(3) 5.6 5 0.650 (16.51) K, M N, L, M, J, K L1X(3)505565(2)(4)65

(1)49470X01685(2)A(3) 6.8 4 0.360 (9.14) K, M N, L, M, J, K L1X(3)405685(2)(4)36

(1)49470X01825(2)A(3) 8.2 4 0.360 (9.14) K, M N, L, M, J, K L1X(3)405825(2)(4)36

(1)49470X01106(2)A(3) 10 4 0.480 (12.19) K, M N, L, M, J, K L1X(3)405106(2)(4)48

(1)49470X01126(2)A(3) 12 4 0.480 (12.19) K, M N, L, M, J, K L1X(3)405126(2)(4)48

(1)49470X01156(2)A(3) 15 4 0.650 (16.51) K, M N, L, M, J, K L1X(3)405156(2)(4)65

(1)49470X01186(2)A(3) 18 3 0.240 (6.10) K, M N, L, M, J, K L1X(3)305186(2)(4)24

(1)49470X01226(2)A(3) 22 3 0.360 (9.14) K, M N, L, M, J, K L1X(3)305226(2)(4)36

(1)49470X01276(2)A(3) 27 3 0.360 (9.14) K, M N, L, M, J, K L1X(3)305276(2)(4)36

(1)49470X01336(2)A(3) 33 3 0.360 (9.14) K, M N, L, M, J, K L1X(3)305336(2)(4)36

(1)49470X01396(2)A(3) 39 3 0.480 (12.19) K, M N, L, M, J, K L1X(3)305396(2)(4)48

(1)49470X01476(2)A(3) 47 3 0.650 (16.51) K, M N, L, M, J, K L1X(3)305476(2)(4)65

100VDC - BX Dielectric

(1)49470X01684(2)B(3) 0.68 5 0.120 (3.05) K, M N, L, M, J, K L1X(3)501684(2)(4)12

(1)49470X01824(2)B(3) 0.82 5 0.240 (6.10) K, M N, L, M, J, K L1X(3)501824(2)(4)24

(1)49470X01105(2)B(3) 1 5 0.240 (6.10) K, M N, L, M, J, K L1X(3)501105(2)(4)24

(1)49470X01125(2)B(3) 1.2 5 0.240 (6.10) K, M N, L, M, J, K L1X(3)501125(2)(4)24

(1)49470X01155(2)B(3) 1.5 5 0.360 (9.14) K, M N, L, M, J, K L1X(3)501155(2)(4)36

(1)49470X01185(2)B(3) 1.8 5 0.360 (9.14) K, M N, L, M, J, K L1X(3)501185(2)(4)36

(1)49470X01225(2)B(3) 2.2 5 0.480 (12.19) K, M N, L, M, J, K L1X(3)501225(2)(4)48

(1)49470X01275(2)B(3) 2.7 5 0.480 (12.19) K, M N, L, M, J, K L1X(3)501275(2)(4)48

(1)49470X01335(2)B(3) 3.3 5 0.650 (16.51) K, M N, L, M, J, K L1X(3)501335(2)(4)65

(1)49470X01395(2)B(3) 3.9 4 0.360 (9.14) K, M N, L, M, J, K L1X(3)401395(2)(4)36

(1)49470X01475(2)B(3) 4.7 4 0.360 (9.14) K, M N, L, M, J, K L1X(3)401475(2)(4)36

(1)49470X01565(2)B(3) 5.6 4 0.480 (12.19) K, M N, L, M, J, K L1X(3)401565(2)(4)48

(1)49470X01685(2)B(3) 6.8 4 0.480 (12.19) K, M N, L, M, J, K L1X(3)401685(2)(4)48

(1)49470X01825(2)B(3) 8.2 4 0.650 (16.51) K, M N, L, M, J, K L1X(3)401825(2)(4)65

(1)49470X01106(2)B(3) 10 3 0.240 (6.10) K, M N, L, M, J, K L1X(3)301106(2)(4)24

(1)49470X01126(2)B(3) 12 3 0.240 (6.10) K, M N, L, M, J, K L1X(3)301126(2)(4)24

(1)49470X01156(2)B(3) 15 3 0.360 (9.14) K, M N, L, M, J, K L1X(3)301156(2)(4)36

(1)49470X01186(2)B(3) 18 3 0.360 (9.14) K, M N, L, M, J, K L1X(3)301186(2)(4)36

(1)49470X01226(2)B(3) 22 3 0.480 (12.19) K, M N, L, M, J, K L1X(3)301226(2)(4)48

(1)49470X01276(2)B(3) 27 3 0.650 (16.51) K, M N, L, M, J, K L1X(3)301276(2)(4)65

200VDC - BR Dielectric

(1)49470R01474(2)C(3) 0.47 5 0.240 (6.10) K, M N, L, M, J, K L1R(3)502474(2)(4)24

(1)49470R01564(2)C(3) 0.56 5 0.240 (6.10) K, M N, L, M, J, K L1R(3)502564(2)(4)24

(1)49470R01684(2)C(3) 0.68 5 0.360 (9.14) K, M N, L, M, J, K L1R(3)502684(2)(4)36

(1)49470R01824(2)C(3) 0.82 5 0.360 (9.14) K, M N, L, M, J, K L1R(3)502824(2)(4)36

(1)49470R01105(2)C(3) 1 5 0.480 (12.19) K, M N, L, M, J, K L1R(3)502105(2)(4)48

MIL-PRF-49470 P/N 1Cap (μF) Case Code

Height A

inch (mm)

Cap

Tolerance

Lead Cong. KEMET P/N 1

Table 1A – MIL-PRF-49470/1, Product Selection 50VDC-200VDC

1 Complete P/N requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and

lead conguration. For each numbered position, available options are as follows:

(1) Test level character "M" for B level, or "T" for T level (MIL-PRF-49470/1 part number only)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

(4) Test level character "B" for B level, or "T" for T level (KEMET part number only)

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

MIL-PRF-49470/1 Unencapsulated, Horizontally Stacked

MIL-PRF-49470 P/N 1Cap (μF) Case

Code

Height A

inch (mm) Cap Tol. Lead

Cong. KEMET P/N 1

(1)49470R01125(2)C(3) 1.2 5 0.480 (12.19) K, M N, L, M, J, K L1R(3)502125(2)(4)48

(1)49470R01155(2)C(3) 1.5 5 0.650 (16.51) K, M N, L, M, J, K L1R(3)502155(2)(4)65

(1)49470R01185(2)C(3) 1.8 4 0.360 (9.14) K, M N, L, M, J, K L1R(3)402185(2)(4)36

(1)49470R01225(2)C(3) 2.2 4 0.360 (9.14) K, M N, L, M, J, K L1R(3)402225(2)(4)36

(1)49470R01275(2)C(3) 2.7 4 0.480 (12.19) K, M N, L, M, J, K L1R(3)402275(2)(4)48

(1)49470R01335(2)C(3) 3.3 4 0.480 (12.19) K, M N, L, M, J, K L1R(3)402335(2)(4)48

(1)49470R01395(2)C(3) 3.9 4 0.650 (16.51) K, M N, L, M, J, K L1R(3)402395(2)(4)65

(1)49470R01475(2)C(3) 4.7 3 0.240 (6.10) K, M N, L, M, J, K L1R(3)302475(2)(4)24

(1)49470R01565(2)C(3) 5.6 3 0.240 (6.10) K, M N, L, M, J, K L1R(3)302565(2)(4)24

(1)49470R01685(2)C(3) 6.8 3 0.360 (9.14) K, M N, L, M, J, K L1R(3)302685(2)(4)36

(1)49470R01825(2)C(3) 8.2 3 0.360 (9.14) K, M N, L, M, J, K L1R(3)302825(2)(4)36

(1)49470R01106(2)C(3) 10 3 0.480 (12.19) K, M N, L, M, J, K L1R(3)302106(2)(4)48

(1)49470R01126(2)C(3) 12 3 0.650 (16.51) K, M N, L, M, J, K L1R(3)302126(2)(4)65

500VDC - BQ Dielectric

(1)49470Q01154(2)E(3) 0.15 5 0.120 (3.05) K, M N, L, M, J, K L1Q(3)50C154(2)(4)12

(1)49470Q01184(2)E(3) 0.18 5 0.240 (6.10) K, M N, L, M, J, K L1Q(3)50C184(2)(4)24

(1)49470Q01224(2)E(3) 0.22 5 0.240 (6.10) K, M N, L, M, J, K L1Q(3)50C224(2)(4)24

(1)49470Q01274(2)E(3) 0.27 5 0.240 (6.10) K, M N, L, M, J, K L1Q(3)50C274(2)(4)24

(1)49470Q01334(2)E(3) 0.33 5 0.360 (9.14) K, M N, L, M, J, K L1Q(3)50C334(2)(4)36

(1)49470Q01394(2)E(3) 0.39 5 0.360 (9.14) K, M N, L, M, J, K L1Q(3)50C394(2)(4)36

(1)49470Q01474(2)E(3) 0.47 5 0.360 (9.14) K, M N, L, M, J, K L1Q(3)50C474(2)(4)36

(1)49470Q01564(2)E(3) 0.56 5 0.480 (12.19) K, M N, L, M, J, K L1Q(3)50C564(2)(4)48

(1)49470Q01684(2)E(3) 0.68 5 0.650 (16.51) K, M N, L, M, J, K L1Q(3)50C684(2)(4)65

(1)49470Q01824(2)E(3) 0.82 4 0.360 (9.14) K, M N, L, M, J, K L1Q(3)40C824(2)(4)36

(1)49470Q01105(2)E(3) 1 4 0.360 (9.14) K, M N, L, M, J, K L1Q(3)40C105(2)(4)36

(1)49470Q01125(2)E(3) 1.2 4 0.360 (9.14) K, M N, L, M, J, K L1Q(3)40C125(2)(4)36

(1)49470Q01155(2)E(3) 1.5 4 0.480 (12.19) K, M N, L, M, J, K L1Q(3)40C155(2)(4)48

(1)49470Q01185(2)E(3) 1.8 4 0.650 (16.51) K, M N, L, M, J, K L1Q(3)40C185(2)(4)65

(1)49470Q01225(2)E(3) 2.2 3 0.240 (6.10) K, M N, L, M, J, K L1Q(3)30C225(2)(4)24

(1)49470Q01275(2)E(3) 2.7 3 0.360 (9.14) K, M N, L, M, J, K L1Q(3)30C275(2)(4)36

(1)49470Q01335(2)E(3) 3.3 3 0.360 (9.14) K, M N, L, M, J, K L1Q(3)30C335(2)(4)36

(1)49470Q01395(2)E(3) 3.9 3 0.360 (9.14) K, M N, L, M, J, K L1Q(3)30C395(2)(4)36

(1)49470Q01475(2)E(3) 4.7 3 0.480 (12.19) K, M N, L, M, J, K L1Q(3)30C475(2)(4)48

(1)49470Q01565(2)E(3) 5.6 3 0.650 (16.51) K, M N, L, M, J, K L1Q(3)30C565(2)(4)65

MIL-PRF-49470 P/N 1Cap (μF) Case Code

Height A

inch (mm)

Cap

Tolerance

Lead Cong. KEMET P/N 1

Table 1A – MIL-PRF-49470 /1, Product Selection 200VDC-500VDC con't.

1 Complete P/N requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance tolerance and

lead conguration. For each numbered position, available options are as follows:

(1) Test level character "M" for B level, or "T" for T level (MIL-PRF-49470/1 part number only)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

(4) Test level character "B" for B level, or "T" for T level (KEMET part number only)

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

MIL-PRF-49470/2 Encapsulated, Horizontally Stacked

MIL-PRF-49470 P/N 1Cap (μF) Case

Code

Height A

inch (mm) Cap Tol. Lead

Cong. KEMET P/N 1

50VDC - BX Dielectric

M49470X02125(1)A(2) 1.2 5 0.270 (6.86) K, M N, L, M, J, K L2X(2)505125(1)B27

M49470X02155(1)A(2) 1.5 5 0.390 (9.91) K, M N, L, M, J, K L2X(2)505155(1)B39

M49470X02185(1)A(2) 1.8 5 0.390 (9.91) K, M N, L, M, J, K L2X(2)505185(1)B39

M49470X02225(1)A(2) 2.2 5 0.390 (9.91) K, M N, L, M, J, K L2X(2)505225(1)B39

M49470X02275(1)A(2) 2.7 5 0.530 (13.46) K, M N, L, M, J, K L2X(2)505275(1)B53

M49470X02335(1)A(2) 3.3 5 0.530 (13.46) K, M N, L, M, J, K L2X(2)505335(1)B53

M49470X02475(1)A(2) 3.9 5 0.660 (16.76) K, M N, L, M, J, K L2X(2)505475(1)B66

M49470X02395(1)A(2) 4.7 5 0.660 (16.76) K, M N, L, M, J, K L2X(2)505395(1)B66

M49470X02565(1)A(2) 5.6 5 0.800 (20.32) K, M N, L, M, J, K L2X(2)505565(1)B80

M49470X02685(1)A(2) 6.8 4 0.530 (13.46) K, M N, L, M, J, K L2X(2)405685(1)B53

M49470X02825(1)A(2) 8.2 4 0.530 (13.46) K, M N, L, M, J, K L2X(2)405825(1)B53

M49470X02106(1)A(2) 10 4 0.660 (16.76) K, M N, L, M, J, K L2X(2)405106(1)B66

M49470X02126(1)A(2) 12 4 0.660 (16.76) K, M N, L, M, J, K L2X(2)405126(1)B66

M49470X02156(1)A(2) 15 4 0.800 (20.32) K, M N, L, M, J, K L2X(2)405156(1)B80

M49470X02186(1)A(2) 18 3 0.390 (9.91) K, M N, L, M, J, K L2X(2)305186(1)B39

M49470X02226(1)A(2) 22 3 0.530 (13.46) K, M N, L, M, J, K L2X(2)305226(1)B53

M49470X02276(1)A(2) 27 3 0.530 (13.46) K, M N, L, M, J, K L2X(2)305276(1)B53

M49470X02336(1)A(2) 33 3 0.530 (13.46) K, M N, L, M, J, K L2X(2)305336(1)B53

M49470X02396(1)A(2) 39 3 0.660 (16.76) K, M N, L, M, J, K L2X(2)305396(1)B66

M49470X02476(1)A(2) 47 3 0.800 (20.32) K, M N, L, M, J, K L2X(2)305476(1)B80

100VDC - BX Dielectric

M49470X02684(1)B(2) 0.68 5 0.270 (6.86) K, M N, L, M, J, K L2X(2)501684(1)B27

M49470X02824(1)B(2) 0.82 5 0.390 (9.91) K, M N, L, M, J, K L2X(2)501824(1)B39

M49470X02105(1)B(2) 1 5 0.390 (9.91) K, M N, L, M, J, K L2X(2)501105(1)B39

M49470X02125(1)B(2) 1.2 5 0.390 (9.91) K, M N, L, M, J, K L2X(2)501125(1)B39

M49470X02155(1)B(2) 1.5 5 0.530 (13.46) K, M N, L, M, J, K L2X(2)501155(1)B53

M49470X02185(1)B(2) 1.8 5 0.530 (13.46) K, M N, L, M, J, K L2X(2)501185(1)B53

M49470X02225(1)B(2) 2.2 5 0.660 (16.76) K, M N, L, M, J, K L2X(2)501225(1)B66

M49470X02275(1)B(2) 2.7 5 0.660 (16.76) K, M N, L, M, J, K L2X(2)501275(1)B66

M49470X02335(1)B(2) 3.3 5 0.800 (20.32) K, M N, L, M, J, K L2X(2)501335(1)B80

M49470X02395(1)B(2) 3.9 4 0.530 (13.46) K, M N, L, M, J, K L2X(2)401395(1)B53

M49470X02475(1)B(2) 4.7 4 0.530 (13.46) K, M N, L, M, J, K L2X(2)401475(1)B53

M49470X02565(1)B(2) 5.6 4 0.660 (16.76) K, M N, L, M, J, K L2X(2)401565(1)B66

M49470X02685(1)B(2) 6.8 4 0.660 (16.76) K, M N, L, M, J, K L2X(2)401685(1)B66

M49470X02825(1)B(2) 8.2 4 0.800 (20.32) K, M N, L, M, J, K L2X(2)401825(1)B80

M49470X02106(1)B(2) 10 3 0.390 (9.91) K, M N, L, M, J, K L2X(2)301106(1)B39

M49470X02126(1)B(2) 12 3 0.390 (9.91) K, M N, L, M, J, K L2X(2)301126(1)B39

M49470X02156(1)B(2) 15 3 0.530 (13.46) K, M N, L, M, J, K L2X(2)301156(1)B53

M49470X02186(1)B(2) 18 3 0.530 (13.46) K, M N, L, M, J, K L2X(2)301186(1)B53

M49470X02226(1)B(2) 22 3 0.660 (16.76) K, M N, L, M, J, K L2X(2)301226(1)B66

M49470X02276(1)B(2) 27 3 0.800 (20.32) K, M N, L, M, J, K L2X(2)301276(1)B80

200VDC - BR Dielectric

M49470R02474(1)C(2) 0.47 5 0.390 (9.91) K, M N, L, M, J, K L2R(2)502474(1)B39

M49470R02564(1)C(2) 0.56 5 0.390 (9.91) K, M N, L, M, J, K L2R(2)502564(1)B39

M49470R02684(1)C(2) 0.68 5 0.530 (13.46) K, M N, L, M, J, K L2R(2)502684(1)B53

M49470R02824(1)C(2) 0.82 5 0.530 (13.46) K, M N, L, M, J, K L2R(2)502824(1)B53

M49470R02105(1)C(2) 1 5 0.660 (16.76) K, M N, L, M, J, K L2R(2)502105(1)B66

M49470R02125(1)C(2) 1.2 5 0.660 (16.76) K, M N, L, M, J, K L2R(2)502125(1)B66

M49470R02155(1)C(2) 1.5 5 0.800 (20.32) K, M N, L, M, J, K L2R(2)502155(1)B80

M49470R02185(1)C(2) 1.8 4 0.530 (13.46) K, M N, L, M, J, K L2R(2)402185(1)B53

M49470R02225(1)C(2) 2.2 4 0.530 (13.46) K, M N, L, M, J, K L2R(2)402225(1)B53

MIL-PRF-49470 P/N 1Cap (μF) Case Code

Height A

inch (mm)

Cap

Tolerance

Lead Cong. KEMET P/N 1

Table 1B – MIL-PRF-49470/2, Product Selection 50VDC-200VDC

1 Complete P/N requires additional characters in the numbered positions provided in order to indicate capacitance tolerance and lead conguration. For each

numbered position, available options are as follows:

(1) Capacitance tolerance character " K" or " M"

(2) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

MIL-PRF-49470/2 Encapsulated, Horizontally Stacked

MIL-PRF-49470 P/N 1Cap (μF) Case

Code

Height A

inch (mm) Cap Tol. Lead

Cong. KEMET P/N 1

M49470R02275(1)C(2) 2.7 4 0.660 (16.76) K, M N, L, M, J, K L2R(2)402275(1)B66

M49470R02335(1)C(2) 3.3 4 0.660 (16.76) K, M N, L, M, J, K L2R(2)402335(1)B66

M49470R02395(1)C(2) 3.9 4 0.800 (20.32) K, M N, L, M, J, K L2R(2)402395(1)B80

M49470R02475(1)C(2) 4.7 3 0.390 (9.91) K, M N, L, M, J, K L2R(2)302475(1)B39

M49470R02565(1)C(2) 5.6 3 0.390 (9.91) K, M N, L, M, J, K L2R(2)302565(1)B39

M49470R02685(1)C(2) 6.8 3 0.530 (13.46) K, M N, L, M, J, K L2R(2)302685(1)B53

M49470R02825(1)C(2) 8.2 3 0.530 (13.46) K, M N, L, M, J, K L2R(2)302825(1)B53

M49470R02106(1)C(2) 10 3 0.660 (16.76) K, M N, L, M, J, K L2R(2)302106(1)B66

M49470R02126(1)C(2) 12 3 0.800 (20.32) K, M N, L, M, J, K L2R(2)302126(1)B80

500VDC - BQ Dielectric

M49470Q02154(1)E(2) 0.15 5 0.270 (6.86) K, M N, L, M, J, K L2Q(2)50C154(1)B27

M49470Q02184(1)E(2) 0.18 5 0.390 (9.91) K, M N, L, M, J, K L2Q(2)50C184(1)B39

M49470Q02224(1)E(2) 0.22 5 0.390 (9.91) K, M N, L, M, J, K L2Q(2)50C224(1)B39

M49470Q02274(1)E(2) 0.27 5 0.390 (9.91) K, M N, L, M, J, K L2Q(2)50C274(1)B39

M49470Q02334(1)E(2) 0.33 5 0.530 (13.46) K, M N, L, M, J, K L2Q(2)50C334(1)B53

M49470Q02394(1)E(2) 0.39 5 0.530 (13.46) K, M N, L, M, J, K L2Q(2)50C394(1)B53

M49470Q02474(1)E(2) 0.47 5 0.530 (13.46) K, M N, L, M, J, K L2Q(2)50C474(1)B53

M49470Q02564(1)E(2) 0.56 5 0.660 (16.76) K, M N, L, M, J, K L2Q(2)50C564(1)B66

M49470Q02684(1)E(2) 0.68 5 0.800 (20.32) K, M N, L, M, J, K L2Q(2)50C684(1)B80

M49470Q02824(1)E(2) 0.82 4 0.530 (13.46) K, M N, L, M, J, K L2Q(2)40C824(1)B53

M49470Q02105(1)E(2) 1 4 0.530 (13.46) K, M N, L, M, J, K L2Q(2)40C105(1)B53

M49470Q02125(1)E(2) 1.2 4 0.530 (13.46) K, M N, L, M, J, K L2Q(2)40C125(1)B53

M49470Q02155(1)E(2) 1.5 4 0.660 (16.76) K, M N, L, M, J, K L2Q(2)40C155(1)B66

M49470Q02185(1)E(2) 1.8 4 0.800 (20.32) K, M N, L, M, J, K L2Q(2)40C185(1)B80

M49470Q02225(1)E(2) 2.2 3 0.390 (9.91) K, M N, L, M, J, K L2Q(2)30C225(1)B39

M49470Q02275(1)E(2) 2.7 3 0.530 (13.46) K, M N, L, M, J, K L2Q(2)30C275(1)B53

M49470Q02335(1)E(2) 3.3 3 0.530 (13.46) K, M N, L, M, J, K L2Q(2)30C335(1)B53

M49470Q02395(1)E(2) 3.9 3 0.530 (13.46) K, M N, L, M, J, K L2Q(2)30C395(1)B53

M49470Q02475(1)E(2) 4.7 3 0.660 (16.76) K, M N, L, M, J, K L2Q(2)30C475(1)B66

M49470Q02565(1)E(2) 5.6 3 0.800 (20.32) K, M N, L, M, J, K L2Q(2)30C565(1)B80

M49470Q02565(1)E(2) 5.6 3 0.800 (20.32) K, M N, L, M, J, K L2Q(2)30C565(1)B65

MIL-PRF-49470 P/N 1Cap (μF) Case Code

Height A

inch (mm)

Cap

Tolerance

Lead Cong. KEMET P/N 1

Table 1B – MIL-PRF-49470 /2, Product Selection 200VDC-500VDC con't

1 Complete P/N requires additional characters in the numbered positions provided in order to indicate capacitance tolerance and lead conguration. For each

numbered position, available options are as follows:

(1) Capacitance tolerance character " K" or " M"

(2) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

25VDC - BX Dielectric

L1X(1)503824(2)(3)12 0.82 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503105(2)(3)12 1 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503125(2)(3)12 1.2 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503155(2)(3)12 1.5 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503185(2)(3)24 1.8 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403225(2)(3)12 2.2 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503225(2)(3)24 2.2 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)503255(2)(3)24 2.5 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403275(2)(3)12 2.7 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503275(2)(3)24 2.7 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403335(2)(3)12 3.3 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503335(2)(3)36 3.3 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)403395(2)(3)12 3.9 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503395(2)(3)36 3.9 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)403475(2)(3)12 4.7 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)503475(2)(3)36 4.7 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)403565(2)(3)24 5.6 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)503565(2)(3)48 5.6 5 0.480 (12.19) K, M N, L, M, J, K

L1X(1)403605(2)(3)24 6 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)503605(2)(3)48 6 5 0.480 (12.19) K, M N, L, M, J, K

L1X(1)303685(2)(3)12 6.8 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)403685(2)(3)24 6.8 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)503685(2)(3)65 6.8 5 0.650 (16.51) K, M N, L, M, J, K

L1X(1)403755(2)(3)24 7.5 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)503755(2)(3)65 7.5 5 0.650 (16.51) K, M N, L, M, J, K

L1X(1)303825(2)(3)12 8.2 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)403825(2)(3)24 8.2 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)303106(2)(3)12 10 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)403106(2)(3)24 10 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)303116(2)(3)12 11 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)303126(2)(3)12 12 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)403126(2)(3)36 12 4 0.360 (9.14) K, M N, L, M, J, K

L1X(1)303156(2)(3)12 15 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)403156(2)(3)36 15 4 0.360 (9.14) K, M N, L, M, J, K

L1X(1)303166(2)(3)24 16 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403166(2)(3)48 16 4 0.480 (12.19) K, M N, L, M, J, K

L1X(1)303186(2)(3)24 18 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403186(2)(3)48 18 4 0.480 (12.19) K, M N, L, M, J, K

L1X(1)303206(2)(3)24 20 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403206(2)(3)48 20 4 0.480 (12.19) K, M N, L, M, J, K

L1X(1)303226(2)(3)24 22 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)403226(2)(3)65 22 4 0.650 (16.51) K, M N, L, M, J, K

L1X(1)403246(2)(3)65 24 4 0.650 (16.51) K, M N, L, M, J, K

L1X(1)303276(2)(3)24 27 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)303306(2)(3)24 30 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)303306(2)(3)36 30 3 0.360 (9.14) K, M N, L, M, J, K

L1X(1)303336(2)(3)36 33 3 0.360 (9.14) K, M N, L, M, J, K

L1X(1)303396(2)(3)36 39 3 0.360 (9.14) K, M N, L, M, J, K

L1X(1)303456(2)(3)36 45 3 0.360 (9.14) K, M N, L, M, J, K

L1X(1)303506(2)(3)48 50 3 0.480 (12.19) K, M N, L, M, J, K

L1X(1)303546(2)(3)48 54 3 0.480 (12.19) K, M N, L, M, J, K

L1X(1)303606(2)(3)48 60 3 0.480 (12.19) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Product Selection 25VDC

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

L1X(1)303666(2)(3)65 66 3 0.650 (16.51) K, M N, L, M, J, K

L1X(1)303726(2)(3)65 72 3 0.650 (16.51) K, M N, L, M, J, K

L1X(1)303756(2)(3)65 75 3 0.650 (16.51) K, M N, L, M, J, K

50VDC - BX Dielectric

L1X(1)505824(2)(3)12 0.82 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505105(2)(3)12 1 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505125(2)(3)12 1.2 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505155(2)(3)12 1.5 5 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505185(2)(3)24 1.8 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)405225(2)(3)12 2.2 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505225(2)(3)24 2.2 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)505255(2)(3)24 2.5 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)405275(2)(3)12 2.7 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505275(2)(3)24 2.7 5 0.240 (6.10) K, M N, L, M, J, K

L1X(1)505275(2)(3)36 2.7 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)405335(2)(3)12 3.3 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505335(2)(3)36 3.3 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)405395(2)(3)12 3.9 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505395(2)(3)36 3.9 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)405475(2)(3)12 4.7 4 0.120 (3.05) K, M N, L, M, J, K

L1X(1)505475(2)(3)36 4.7 5 0.360 (9.14) K, M N, L, M, J, K

L1X(1)405565(2)(3)24 5.6 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)505565(2)(3)48 5.6 5 0.480 (12.19) K, M N, L, M, J, K

L1X(1)405605(2)(3)24 6 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)505605(2)(3)48 6 5 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305685(2)(3)12 6.8 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)405685(2)(3)24 6.8 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)505685(2)(3)65 6.8 5 0.650 (16.51) K, M N, L, M, J, K

L1X(1)405755(2)(3)24 7.5 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)505755(2)(3)65 7. 5 5 0.650 (16.51) K, M N, L, M, J, K

L1X(1)305825(2)(3)12 8.2 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)405825(2)(3)24 8.2 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)305106(2)(3)12 10 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)405106(2)(3)24 10 4 0.240 (6.10) K, M N, L, M, J, K

L1X(1)305116(2)(3)12 11 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)305126(2)(3)12 12 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)405126(2)(3)36 12 4 0.360 (9.14) K, M N, L, M, J, K

L1X(1)305156(2)(3)12 15 3 0.120 (3.05) K, M N, L, M, J, K

L1X(1)405156(2)(3)36 15 4 0.360 (9.14) K, M N, L, M, J, K

L1X(1)305166(2)(3)24 16 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)405166(2)(3)48 16 4 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305186(2)(3)24 18 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)405186(2)(3)48 18 4 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305206(2)(3)24 20 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)405206(2)(3)48 20 4 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305226(2)(3)24 22 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)405226(2)(3)65 22 4 0.650 (16.51) K, M N, L, M, J, K

L1X(1)405246(2)(3)65 24 4 0.650 (16.51) K, M N, L, M, J, K

L1X(1)305276(2)(3)24 27 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)305306(2)(3)24 30 3 0.240 (6.10) K, M N, L, M, J, K

L1X(1)305336(2)(3)36 33 3 0.360 (9.14) K, M N, L, M, J, K

L1X(1)305396(2)(3)36 39 3 0.360 (9.14) K, M N, L, M, J, K

L1X(1)305456(2)(3)36 45 3 0.360 (9.14) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Commercial/Non-Standard – Product Selection 25VDC-50VDC con't.

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

L1X(1)305506(2)(3)48 50 3 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305546(2)(3)48 54 3 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305606(2)(3)48 60 3 0.480 (12.19) K, M N, L, M, J, K

L1X(1)305666(2)(3)65 66 3 0.650 (16.51) K, M N, L, M, J, K

L1X(1)305726(2)(3)65 72 3 0.650 (16.51) K, M N, L, M, J, K

L1X(1)305756(2)(3)65 75 3 0.650 (16.51) K, M N, L, M, J, K

100VDC - BR Dielectric

L1R(1)501564(2)(3)12 0.56 5 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501684(2)(3)12 0.68 5 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501754(2)(3)12 0.75 5 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501824(2)(3)12 0.82 5 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501105(2)(3)12 1 5 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501125(2)(3)12 1.2 5 0.120 (3.05) K, M N, L, M, J, K

L1R(1)401155(2)(3)12 1.5 4 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501155(2)(3)24 1.5 5 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401185(2)(3)12 1.8 4 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501185(2)(3)24 1.8 5 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401225(2)(3)12 2.2 4 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501225(2)(3)24 2.2 5 0.240 (6.10) K, M N, L, M, J, K

L1R(1)501255(2)(3)24 2.5 5 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401275(2)(3)12 2.7 4 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501275(2)(3)36 2.7 5 0.360 (9.14) K, M N, L, M, J, K

L1R(1)401335(2)(3)12 3.3 4 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501335(2)(3)36 3.3 5 0.360 (9.14) K, M N, L, M, J, K

L1R(1)401395(2)(3)12 3.9 4 0.120 (3.05) K, M N, L, M, J, K

L1R(1)501395(2)(3)48 3.9 5 0.480 (12.19) K, M N, L, M, J, K

L1R(1)401475(2)(3)24 4.7 4 0.240 (6.10) K, M N, L, M, J, K

L1R(1)501475(2)(3)48 4.7 5 0.480 (12.19) K, M N, L, M, J, K

L1R(1)301565(2)(3)12 5.6 3 0.120 (3.05) K, M N, L, M, J, K

L1R(1)401565(2)(3)24 5.6 4 0.240 (6.10) K, M N, L, M, J, K

L1R(1)501565(2)(3)65 5.6 5 0.650 (16.51) K, M N, L, M, J, K

L1R(1)301605(2)(3)12 6 3 0.120 (3.05) K, M N, L, M, J, K

L1R(1)401605(2)(3)24 6 4 0.240 (6.10) K, M N, L, M, J, K

L1R(1)501605(2)(3)65 6 5 0.650 (16.51) K, M N, L, M, J, K

L1R(1)301685(2)(3)12 6.8 3 0.120 (3.05) K, M N, L, M, J, K

L1R(1)401685(2)(3)24 6.8 4 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401755(2)(3)24 7.5 4 0.240 (6.10) K, M N, L, M, J, K

L1R(1)301825(2)(3)12 8.2 3 0.120 (3.05) K, M N, L, M, J, K

L1R(1)401825(2)(3)36 8.2 4 0.360 (9.14) K, M N, L, M, J, K

L1R(1)301106(2)(3)12 10 3 0.120 (3.05) K, M N, L, M, J, K

L1R(1)401106(2)(3)36 10 4 0.360 (9.14) K, M N, L, M, J, K

L1R(1)301116(2)(3)12 11 3 0.120 (3.05) K, M N, L, M, J, K

L1R(1)301126(2)(3)24 12 3 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401126(2)(3)48 12 4 0.480 (12.19) K, M N, L, M, J, K

L1R(1)301156(2)(3)24 15 3 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401156(2)(3)48 15 4 0.480 (12.19) K, M N, L, M, J, K

L1R(1)301166(2)(3)24 16 3 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401166(2)(3)65 16 4 0.650 (16.51) K, M N, L, M, J, K

L1R(1)301186(2)(3)24 18 3 0.240 (6.10) K, M N, L, M, J, K

L1R(1)401186(2)(3)65 18 4 0.650 (16.51) K, M N, L, M, J, K

L1R(1)301206(2)(3)24 20 3 0.240 (6.10) K, M N, L, M, J, K

L1R(1)301226(2)(3)36 22 3 0.360 (9.14) K, M N, L, M, J, K

L1R(1)301276(2)(3)36 27 3 0.360 (9.14) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Commercial/Non-Standard – Product Selection 50VDC-100VDC con't.

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

L1R(1)301306(2)(3)36 30 3 0.360 (9.14) K, M N, L, M, J, K

L1R(1)301336(2)(3)48 33 3 0.480 (12.19) K, M N, L, M, J, K

L1R(1)301396(2)(3)48 39 3 0.480 (12.19) K, M N, L, M, J, K

L1R(1)301456(2)(3)65 45 3 0.650 (16.51) K, M N, L, M, J, K

L1R(1)301506(2)(3)65 50 3 0.650 (16.51) K, M N, L, M, J, K

200VDC - BQ Dielectric

L1Q(1)502334(2)(3)12 0.33 5 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502394(2)(3)12 0.39 5 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502474(2)(3)12 0.47 5 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502564(2)(3)12 0.56 5 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502684(2)(3)12 0.68 5 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502754(2)(3)12 0.75 5 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402824(2)(3)12 0.82 4 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502824(2)(3)24 0.82 5 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)402105(2)(3)12 1 4 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502105(2)(3)24 1 5 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)402125(2)(3)12 1.2 4 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502125(2)(3)24 1.2 5 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)402155(2)(3)12 1.5 4 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502155(2)(3)36 1.5 5 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)402185(2)(3)12 1.8 4 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502185(2)(3)36 1.8 5 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)402225(2)(3)24 2.2 4 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)502225(2)(3)48 2.2 5 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)302245(2)(3)12 2.4 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)502255(2)(3)48 2.5 5 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)302275(2)(3)12 2.7 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402275(2)(3)24 2.7 4 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)502275(2)(3)48 2.7 5 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)302335(2)(3)12 3.3 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402335(2)(3)24 3.3 4 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)502335(2)(3)65 3.3 5 0.650 (16.51) K, M N, L, M, J, K

L1Q(1)302365(2)(3)12 3.6 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)302395(2)(3)12 3.9 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402395(2)(3)24 3.9 4 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)302475(2)(3)12 4.7 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402475(2)(3)36 4.7 4 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)302565(2)(3)12 5.6 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402565(2)(3)36 5.6 4 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)302605(2)(3)12 6 3 0.120 (3.05) K, M N, L, M, J, K

L1Q(1)402605(2)(3)36 6 4 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)302685(2)(3)24 6.8 3 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)402685(2)(3)48 6.8 4 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)402755(2)(3)48 7.5 4 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)302825(2)(3)24 8.2 3 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)402825(2)(3)65 8.2 4 0.650 (16.51) K, M N, L, M, J, K

L1Q(1)302106(2)(3)24 10 3 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)402106(2)(3)65 10 4 0.650 (16.51) K, M N, L, M, J, K

L1Q(1)302116(2)(3)24 11 3 0.240 (6.10) K, M N, L, M, J, K

L1Q(1)302126(2)(3)36 12 3 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)302156(2)(3)36 15 3 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)302166(2)(3)36 16 3 0.360 (9.14) K, M N, L, M, J, K

L1Q(1)302186(2)(3)48 18 3 0.480 (12.19) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Commercial/Non-Standard – Product Selection 100VDC-200VDC con't.

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

L1Q(1)302206(2)(3)48 20 3 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)302226(2)(3)48 22 3 0.480 (12.19) K, M N, L, M, J, K

L1Q(1)302276(2)(3)65 27 3 0.650 (16.51) K, M N, L, M, J, K

500VDC - X7R Dielectric

L1W(1)50C124(2)(3)12 0.12 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C154(2)(3)12 0.15 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C184(2)(3)12 0.18 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C224(2)(3)12 0.22 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C274(2)(3)12 0.27 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C334(2)(3)24 0.33 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40C394(2)(3)12 0.39 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C394(2)(3)24 0.39 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40C474(2)(3)12 0.47 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C474(2)(3)24 0.47 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50C564(2)(3)24 0.56 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40C684(2)(3)12 0.68 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C684(2)(3)36 0.68 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)50C754(2)(3)36 0.75 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)40C824(2)(3)12 0.82 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50C824(2)(3)36 0.82 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30C105(2)(3)12 1 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40C105(2)(3)24 1 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50C105(2)(3)48 1 5 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30C125(2)(3)12 1.2 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40C125(2)(3)24 1.2 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50C125(2)(3)65 1.2 5 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30C155(2)(3)12 1.5 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40C155(2)(3)24 1.5 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50C155(2)(3)65 1.5 5 0.650 (16.51) K, M N, L, M, J, K

L1W(1)40C185(2)(3)36 1.8 4 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30C225(2)(3)12 2.2 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40C225(2)(3)36 2.2 4 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30C245(2)(3)12 2.4 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)30C275(2)(3)12 2.7 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40C275(2)(3)48 2.7 4 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30C335(2)(3)24 3.3 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40C335(2)(3)48 3.3 4 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30C365(2)(3)24 3.6 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30C395(2)(3)24 3.9 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40C395(2)(3)65 3.9 4 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30C475(2)(3)24 4.7 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30C565(2)(3)24 5.6 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30C605(2)(3)24 6 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30C685(2)(3)36 6.8 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30C825(2)(3)36 8.2 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30C106(2)(3)48 10 3 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30C116(2)(3)65 11 3 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30C126(2)(3)65 12 3 0.650 (16.51) K, M N, L, M, J, K

630VDC - X7R Dielectric

L1W(1)50B683(2)(3)12 0.068 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B104(2)(3)12 0.1 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50B104(2)(3)12 0.1 5 0.120 (3.05) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Commercial/Non-Standard – Product Selection 200VDC-630VDC con't.

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

L1W(1)50B124(2)(3)12 0.12 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50B154(2)(3)12 0.15 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50B184(2)(3)24 0.18 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30B224(2)(3)12 0.22 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B224(2)(3)12 0.22 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50B224(2)(3)24 0.22 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50B274(2)(3)24 0.27 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30B334(2)(3)12 0.33 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50B334(2)(3)36 0.33 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)40B394(2)(3)12 0.39 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50B394(2)(3)36 0.39 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B474(2)(3)12 0.47 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B474(2)(3)24 0.47 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50B474(2)(3)36 0.47 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)50B564(2)(3)48 0.56 5 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30B684(2)(3)12 0.68 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B684(2)(3)24 0.68 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50B684(2)(3)65 0.68 5 0.650 (16.51) K, M N, L, M, J, K

L1W(1)50B754(2)(3)65 0.75 5 0.650 (16.51) K, M N, L, M, J, K

L1W(1)40B824(2)(3)24 0.82 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30B105(2)(3)12 1 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B105(2)(3)36 1 4 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B125(2)(3)12 1.2 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B125(2)(3)36 1.2 4 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B155(2)(3)12 1.5 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40B155(2)(3)48 1.5 4 0.480 (12.19) K, M N, L, M, J, K

L1W(1)40B185(2)(3)48 1.8 4 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30B225(2)(3)24 2.2 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40B225(2)(3)65 2.2 4 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30B245(2)(3)24 2.4 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30B275(2)(3)24 2.7 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30B335(2)(3)36 3.3 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B365(2)(3)36 3.6 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B395(2)(3)36 3.9 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B475(2)(3)36 4.7 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30B565(2)(3)48 5.6 3 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30B605(2)(3)65 6 3 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30B685(2)(3)65 6.8 3 0.650 (16.51) K, M N, L, M, J, K

1000VDC - X7R Dielectric

L1W(1)50D473(2)(3)12 0.047 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50D683(2)(3)12 0.068 5 0.120 (3.05) K, M N, L, M, J, K

L1W(1)30D104(2)(3)12 0.1 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40D104(2)(3)12 0.1 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50D104(2)(3)24 0.1 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50D124(2)(3)24 0.12 5 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50D154(2)(3)36 0.15 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)50D184(2)(3)36 0.18 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30D224(2)(3)12 0.22 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40D224(2)(3)12 0.22 4 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50D224(2)(3)36 0.22 5 0.360 (9.14) K, M N, L, M, J, K

L1W(1)50D274(2)(3)48 0.27 5 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30D334(2)(3)12 0.33 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)50D334(2)(3)65 0.33 5 0.650 (16.51) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Commercial/Non-Standard – Product Selection 630VDC-1000VDC con't.

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Commercial/Non-Standard – Customer Specic Unencapsulated, Horizontally Stacked

KEMET P/N 1Cap (μF) Case Code Height A inch

(mm) Cap Tolerance Lead Cong.

L1W(1)40D394(2)(3)24 0.39 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)50D394(2)(3)65 0.39 5 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30D474(2)(3)12 0.47 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40D474(2)(3)24 0.47 4 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30D684(2)(3)12 0.68 3 0.120 (3.05) K, M N, L, M, J, K

L1W(1)40D684(2)(3)36 0.68 4 0.360 (9.14) K, M N, L, M, J, K

L1W(1)40D824(2)(3)48 0.82 4 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30D105(2)(3)24 1 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)40D105(2)(3)65 1 4 0.650 (16.51) K, M N, L, M, J, K

L1W(1)30D125(2)(3)24 1.2 3 0.240 (6.10) K, M N, L, M, J, K

L1W(1)30D155(2)(3)36 1.5 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30D225(2)(3)36 2.2 3 0.360 (9.14) K, M N, L, M, J, K

L1W(1)30D245(2)(3)48 2.4 3 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30D275(2)(3)48 2.7 3 0.480 (12.19) K, M N, L, M, J, K

L1W(1)30D335(2)(3)65 3.3 3 0.650 (16.51) K, M N, L, M, J, K

KEMET P/N 1Cap (μF) Case Code Height A inch (mm) Cap Tolerance Lead Cong.

Table 1C – Commercial/Non-Standard – Product Selection 1000VDC con't.

1 Complete part number requires additional characters in the numbered positions provided in order to indicate product level (B level or T level), capacitance

tolerance and lead conguration. For each numbered position, available options are as follows:

(1) Test Level character "S" for Commercial, or "X" for non-standard (customer specic)

(2) Capacitance tolerance character " K" or " M"

(3) Lead style character " N", "L", "M", "J" or "K"

Roll Over for

Order Info.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Soldering Process

The capacitors and assemblies outlined in this specication sheet are susceptible to thermal shock damage due to their large ceramic

mass. Temperature proles used should provide adequate temperature rise and cool-down time to prevent damage from thermal

shock. In general, KEMET recommends against hand soldering for these types of large ceramic devices.

Recommended Soldering Technique:

• Solder reow only

Recommended Reow Soldering Prole:

Time

Temperature

Tsmin

25°C to Peak

Tsmax

Max Ramp Up Rate = 2°C/sec

Max Ramp Down Rate = 2°C/sec

Prole Feature Sn-Pb Assembly

Preheat/Soak

Temperature Min (T

Smin

) 100°C

Temperature Max (T

Smax

)150°C

Time (t

) from T

smin

to T

smax

) 60-90 sec

Ramp-up rate (T

to T

)2°C/sec

Liquidous temperature (T

)183°C

Time above liquidous (t

) 95 sec

Peak Temperature (T

)240°C

Time within 5° C of max peak

temperature (tP)5 sec

Ramp-down rate (T

to T

)2°C/sec

Time 25° C to peak temperature 3.5 minutes

Note 1: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reow

Preheating and Reow Prole Notes:

Due to differences in the coefcient of thermal expansion for the different materials of construction, it is critical to monitor and control the heating and cooling rates

during the soldering process. During the reow soldering process, the maximum recommended heating and cooling rate (dT/dt) is 4°C/second. To ensure optimal

component reliability, KEMET's recommended heating and cooling rate is 2°C/second. After soldering, the capacitors should be air cooled to room temperature

before further processing. Forced air cooling is not recommended.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Table 4 – Performance & Reliability: Test Methods and Conditions

Inspection Test Method

Test Level Option

MI L-P RF- 4 9470

B Level (B)

MIL- PRF- 49470

T Level (T)

DSSC Drawing

87106 (C)1

Commercial

(S) Non-Standard (X)2

In-Process Inspection

Ultrasonic Scanning

(C-SAM) Meet EIA-469 Criteria

Not required Yes (per lot) Not required Not

required

Optional per

Source Controlled

Drawing (SCD)

DPA Analysis EIA-469

In-Process Visual

Inspection

MIL- PRF- 49470

Method 4.8.3

Group A Requirements

Thermal Shock

MIL-STD-202 Method

107

Yes (5 cycles) Yes (20 cycles) Yes (5 cycles)

Not

required

Optional per

Source Controlled

Drawing (SCD)

Voltage Conditioning

≤200V

500V

MIL- PRF- 49470

Method 4.8.5.2

200%Vr @125°C

120%Vr @125°C

Yes (96 hrs min.) Yes (168 hrs min.) Yes (96 hrs min.)

Visual and Mechanical

Inspection

MIL- PRF- 49470

Method 4.8.4 Yes (per lot)

Yes (per lot)

Yes (per lot) Yes (per lot)

Solderability MIL-STD-202

Method 208

Yes (per Inspection

lot)

Yes (per

inspection lot) Optional per

Source Controlled

Drawing (SCD)

DPA Analysis EIA-469 Not required Not required

Group B Requirements

Voltage-Temperature Limits

(TCVC)

MIL- PRF- 49470

Method 4.8.13.2

Yes (periodic)

Yes (per lot)

Yes (periodic)

Not

required

Optional per

Source Controlled

Drawing (SCD)

Resistance to Solvents

MIL-STD-202 Method

215

Terminal Strength

MIL-STD-202 Method

211

Resistance to Soldering

Heat

MIL-STD-202 Method

210

Moisture Resistance

MIL-STD-202

Method 106

Marking Legibility

MIL- PRF- 49470

Method 4.8.4.1

Low Voltage Humidity

Testing

MIL-STD-202

Method 103 Not required Not required

Life Test

≤200V

500V

MIL-STD-202

Method 108

200%Vr @125°C

120%Vr @125°C

Yes (periodic) Yes (periodic)

Thermal Shock

MIL-STD-202 Method

107

Not required Not required

KEMET Requirements

Visual and Mechanical

Inspection (100%) KEMET Standard Yes Yes Yes Yes Yes

Voltage Conditioning

1 As per discretionary statement outlined in cancelled DSCC Drawing 87106, KEMET will not perform Group B inspections on a per lot basis. KEMET 87106 orders

may include a standard certicate of compliance stating compliance to the 87106 requirements, specically conformance to Group B inspections. Please contact

KEMET for additional details

2 Non-standard test level option is designated to satisfy customer specic testing requirements that may deviate from those stated in a Mil-Spec or DSCC drawing.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Product Marking

Capacitors shall be marked with KEMET's name, trademark or (CAGE) code, date, capacitance and capacitance tolerance codes.

The date code shall consist of the year and week. For example, the third week of 2011

would be 1103 using a 4-digit date code or 103 using a 3-digit date code. At the option of the

manufacturer, the date code may be placed on a separate line. Full marking shall be included

on the package.

MIL-PRF-49470

Capacitor marking will include "JAN" or "J." Case code 4 or 5 example

Case codes 4 and 5 shall be marked with the following sequence of information:

J brand (1 digit), product level designator (“B” or “T”)

Manufacturer's identication (1 to 5 digits)

Capacitance code (3 digits) and capacitance tolerance (1 digit)

Date code (3 or 4 digits)

Case code 3 shall either be fully marked or partially marked like case code 4 or 5 parts at the option of KEMET.

DSCC 87106

Marking shall be in accordance with MIL-STD-1285, except the parts shall be marked with the part number as specied in paragraph

1.2 of DSCC Drawing 87106 with the manufacturer's name or code and date code minimum. Case sizes 4 and 5 shall be marked with

coded capacitance and tolerance minimum. Full marking shall be included on the package.

Storage and Handling

Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other

environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term

storage. In addition, packaging materials will be degraded by high temperature – reels may soften or warp, and tape peel force may

increase. KEMET recommends that maximum storage temperature not exceed 40 degrees C, and maximum storage humidity not

exceed 70% relative humidity. In addition, temperature uctuations should be minimized to avoid condensation on the parts, and

atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be used promptly,

preferably within 1.5 years of receipt.

Packaging

Shipping Container Packaging Quantities

Case Code Small Box Quantity1 (7.5” x 7.5”) Large Box Quantity1 (13.0” x 13.0” )

3 28 104

4 36 144

5 64 225

1 Minimum order value applies. Contact KEMET for details.

12345

106K

1103

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Application Notes

Notice of KEMET MIL-PRF-49470 Qualied Products Listing (QPL) Status.

KEMET is qualied to supply MIL-PRF-49470/1 unencapsulated X7R Case Codes 3, 4, & 5 ceramic SMPS capacitors in DC voltage ratings of 50V, 100V, 200V,

and 500V. This qualication includes both "B" and "T" test levels.

KEMET is also qualied to supply MIL-PRF-49470/2 encapsulated X7R Case Codes 3, 4, & 5 ceramic SMPS capacitors in DC voltage ratings of 50V, 100V, 200V,

and 500V. This qualication includes "B" level testing only.

Notice of Cancellation: DSCC Drawing 87106 was cancelled on January 3rd 2005.

MIL-PRF-49470 parts are preferred and direct replacements.

MIL-PRF-49470 capacitors are preferred over DSCC 87106 capacitors. The MIL-PRF-49470 specication was developed as part of a cooperative effort between

the U.S. Military, NASA and the switch mode power supply capacitor manufacturers to produce a robust direct replacement for the DSCC drawing. The military

specication product provides additional quality assurance provisions that are NOT required by the DSCC drawing. Two product levels are offered in MIL-

PRF-49470: the standard "B" level and the high reliability "T" level. Some of the benets of the MIL-PRF-49470 product over the 87106 product include the

following: Formal qualication process (QPL established), MIL-STD-790 compliance, DSCC audits, routine qualication maintenance testing, i.e., life testing, group

A percent defective allowed (PDA) specied, and prohibiting the mixing of chips from different production lots within a single SMPS capacitor stack lot.

MIL-PRF-49470 "T" Level product is recommended for all high reliability applications. MIL-PRF-49470 "T" level product requires the following in-process

inspections and additional group A and B screening inspections that are not part of the normal "B" level ow: In-process screening that includes non-destructive

internal examination (chip level) and destructive physical analysis (chip level), group A destructive physical analysis (nished stack level), group B lot specic

humidity, steady-state, low voltage (lot sample test), and group B lot specic thermal shock & life test (lot sample test).

For additional information regarding KEMET MIL-PRF-49470 QPL status or cancellation of DSCC Drawing 87106, please visit the DSCC website at:

www.dscc.dla.mil.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

KEMET Corporation

World Headquarters

2835 KEMET Way

Simpsonville, SC 29681

Mailing Address:

P.O. Box 5928

Greenville, SC 29606

www.kemet.com

Tel: 864-963-6300

Fax: 864-963-6521

Corporate Of ces

Fort Lauderdale, FL

Tel: 954-766-2800

North America

Southeast

Lake Mary, FL

Tel: 407-855-8886

Northeast

Wilmington, MA

Tel: 978-658-1663

West Chester, PA

Tel: 610-692-4642

Central

Schaumburg, IL

Tel: 847-882-3590

Carmel, IN

Tel: 317-706-6742

West

Milpitas, CA

Tel: 408-433-9950

Mexico

Zapopan, Jalisco

Tel: 52-33-3123-2141

Europe

Southern Europe

Geneva, Switzerland

Tel: 41-22-715-0100

Paris, France

Tel: 33-1-4646-1009

Sasso Marconi, Italy

Tel: 39 -051-939111

Milan, Italy

Tel: 39-02-57518176

Rome, Italy

Tel: 39-06-23231718

Madrid, Spain

Tel: 34-91-804-4303

Central Europe

Landsberg, Germany

Tel: 49-8191-3350800

Dortmund, Germany

Tel: 49-2307-3619672

Kwidzyn, Poland

Tel: 48-55-279-7025

Northern Europe

Bishop’s Stortford, United Kingdom

Tel: 44-1279-757201

Weymouth, United Kingdom

Tel: 44-1305-830747

Coatbridge, Scotland

Tel: 44-1236-434455

Färjestaden, Sweden

Tel: 46-485-563934

Espoo, Finland

Tel: 358-9-5406-5000

Asia

Northeast Asia

Hong Kong

Tel: 852-2305-1168

Shenzhen, China

Tel: 86-755-2518-1306

Beijing, China

Tel: 86-10-5829-1711

Shanghai, China

Tel: 86-21-6447-0707

Taipei, Taiwan

Tel: 886-2-27528585

Southeast Asia

Singapore

Tel: 65-6586-1900

Penang, Malaysia

Tel: 60-4-6430200

Bangalore, India

Tel: 91-806-53-76817

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not

assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of

KEMET Electronics Corporation.

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Other KEMET Resources

Disclaimer

All product speci cations, statements, information and data (collectively, the “Information”) are subject to change without notice.

All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we

speci cally disclaim – any warranty concerning suitability for a speci c customer application or use. This Information is intended for use only by customers who have the requisite

experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the

use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.

Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur.

Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or

redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.

Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not

be required.

Tools

Resource Location

Con gure A Part: CapEdge http://capacitoredge.kemet.com

SPICE & FIT Software http://www.kemet.com/spice

Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask

Product Information

Resource Location

Products http://www.kemet.com/products

Technical Resources (Including Soldering

Techniques) http://www.kemet.com/technicalpapers

RoHS Statement http://www.kemet.com/rohs

Quality Documents http://www.kemet.com/qualitydocuments

Product Request

Resource Location

Sample Request http://www.kemet.com/sample

Engineering Kit Request http://www.kemet.com/kits

Contact

Resource Location

Website www.kemet.com

Investor Relations http://www.kemet.com/ir

Call Us 1-877-MyKEMET

Twitter http://twitter.com/kemetcapacitors

Surface Mount & Through-Hole Multilayer Ceramic Chip Stacked Capacitors –KPS MIL Series, SMPS Stacked Capacitors

Digitally signed by Marcy Brand

DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand,

email=marcybrand@kemet.com

Date: 2011.08.12 15:07:08 -04'00'