MKP 1839 Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type FEATURES Supplied loose in box, taped on ammopack or reel RoHS compliant Odt 40.0 5.0 L Max. 40.0 5.0 D Max. ENCAPSULATION Plastic-wrapped, epoxy resin sealed. Flame retardant. LEAD DIAMETER dt (mm) D (mm) L (mm) CLIMATIC TESTING CLASS ACC. TO IEC 60068-1 0.6 0.06 9.0 19.0 55/100/56 0.8 0.08 < 16.5 > 26.5 1.0 0.1 > 16.5 > 26.5 CAPACITANCE RANGE (E12 SERIES) 47 pF to 22 F APPLICATIONS Pulse operations, SMPS and thyristor circuits, storage, filter, timing and sample and hold circuits. CAPACITANCE TOLERANCE REFERENCE STANDARDS LEADS IEC 60384-16 Tinned wire MARKING MAXIMUM APPLICATION TEMPERATURE C-value; tolerance; rated voltage; manufacturer's type; code for dielectric material; manufacturer location; manufacturer's logo; year and week 100 C 10 %, 5 %, 2.5 %, 2 %, 1 % PULL TEST ON LEADS 20 N in direction of leads according to IEC 60068-2-21 DIELECTRIC Polypropylene film BENT TEST ON LEADS 2 bends trough 90 with half of the force used in pull test ELECTRODES Metallized DETAIL SPECIFICATION CONSTRUCTION For more detailed data and test requirements contact: dc-film@vishay.com Mono construction RATED (DC) VOLTAGE 160 V, 250 V, 400 V, 630 V RATED (AC) VOLTAGE 100 V, 160 V, 220 V, 250 V www.vishay.com 248 For technical questions, contact: dc-film@vishay.com Document Number: 26022 Revision: 16-Jan-09 MKP 1839 AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type Vishay Roederstein COMPOSITION OF CATALOG NUMBER MULTIPLIER (nF) SPECIAL LETTER FOR TAPED CAPACITANCE (numerically) 0.1 2 1 3 10 4 100 5 Bulk Example: 468 = 680 nF R Reel G Ammopack TYPE MKP 1839 X XX 16 X VOLTAGE (Vdc) X TOLERANCE 16 = 160 V 1 1% 25 = 250 V 2 2% 40 = 400 V 3 2.5 % 63 = 630 V 4 5% 5 10 % Note (1) For detailed tape specifications refer to "Packaging Information": www.vishay.com/doc?28139 or end of catalog SPECIFIC REFERENCE DATA DESCRIPTION VALUE Tangent of loss angle: at 1 kHz at 10 kHz at 100 kHz C 0.1 F 4 x 10-4 6 x 10-4 40 x 10-4 10-4 10-4 - - - 0.1 F < C 1.0 F 4x C > 1.0 F 10 x 10-4 Capacitor length (mm) 6x Maximum pulse rise time (dU/dt)R [V/s] 160 Vdc 250 Vdc 400 Vdc 630 Vdc 11 240 300 515 700 14 175 220 380 510 19 100 125 200 280 26.5 60 75 120 160 31.5 45 60 95 120 41.5 30 40 65 85 If the maximum pulse voltage is less than the rated voltage higher dU/dt values can be permitted. R between leads, for C 0.33 F at 100 V, 1 min RC between leads, for C > 0.33 F at 100 V, 1 min R between leads and case, 100 V, 1 min > 30 000 s > 30 000 M Withstanding (DC) voltage between leads and wrapped film (1.4 x URac + 2000) Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Maximum application temperature Document Number: 26022 Revision: 16-Jan-09 > 100 000 M 2840 V, 1 min 1.6 x URdc, 1 min 100 C For technical questions, contact: dc-film@vishay.com www.vishay.com 249 MKP 1839 Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type CAPACITANCE CAPACITANCE CODE 47 pF 51 pF 56 pF 62 pF 68 pF 75 pF 82 pF 91 pF 100 pF 110 pF 120 pF 130 pF 150 pF 160 pF 180 pF 200 pF 220 pF 240 pF 270 pF 300 pF 330 pF 360 pF 390 pF 430 pF 470 pF 510 pF 560 pF 620 pF 680 pF 750 pF 820 pF 910 pF 1000 pF 1100 pF 1200 pF 1300 pF 1500 pF 1600 pF 1800 pF 2000 pF 2200 pF 2400 pF 2700 pF 3000 pF 3300 pF 3600 pF 3900 pF 4300 pF 4700 pF 6200 pF 6800 pF www.vishay.com 250 047 051 056 056 068 075 082 091 110 111 112 113 115 116 118 120 122 124 127 130 133 136 139 143 147 151 156 162 168 175 182 191 210 211 212 213 215 216 218 220 222 224 227 230 233 236 239 243 247 262 268 VOLTAGE CODE 16 160 Vdc/100Vac L D (mm) (mm) - - VOLTAGE CODE 25 250 Vdc/160Vac L D (mm) (mm) - VOLTAGE CODE 40 400 Vdc/220Vac (1) L D (mm) (mm) - For technical questions, contact: dc-film@vishay.com 5.0 11.0 VOLTAGE CODE 63 630 Vdc/250Vac (1) L D (mm) (mm) 5.0 5.0 5.0 5.0 5.5 5.5 5.5 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.5 5.5 5.5 5.5 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.5 5.5 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 Document Number: 26022 Revision: 16-Jan-09 MKP 1839 AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type CAPACITANCE CAPACITANCE CODE 8200 pF 0.01 F 0.015 F 0.022 F 0.033 F 0.047 F 0.068 F 0.1 F 0.15 F 0.22 F 0.33 F 0.47 F 0.68 F 1.0 F 1.5 F 2.2 F 3.3 F 4.7 F 6.8 F 10 F 15 F 22 F VOLTAGE CODE 16 160 Vdc/100Vac L D (mm) (mm) 282 310 315 322 333 347 368 410 415 422 433 447 468 510 515 522 533 547 568 610 615 622 5.0 5.5 6.0 6.5 7.5 7.0 8.0 9.0 8.5 10.5 12.0 13.0 15.5 15.5 18.5 22.0 24.5 28.5 VOLTAGE CODE 25 250 Vdc/160Vac L D (mm) (mm) 11.0 11.0 11.0 14.0 14.0 19.0 19.0 19.0 26.5 26.5 26.5 31.5 31.5 41.5 41.5 41.5 41.5 41.5 5.0 5.0 5.0 5.5 6.0 6.5 7.5 7.0 8.5 8.0 9.0 11.0 12.5 13.0 16.0 19.0 19.5 23.0 22.0 24.5 28.5 11.0 11.0 11.0 11.0 14.0 14.0 14.0 19.0 19.0 26.5 26.5 26.5 26.5 31.5 31.5 31.5 41.5 41.5 41.5 41.5 41.5 Vishay Roederstein VOLTAGE CODE 40 400 Vdc/220Vac (1) L D (mm) (mm) 5.0 5.5 6.0 6.5 7.0 8.0 8.5 9.0 8.0 9.5 11.5 13.5 14.0 17.0 20.5 21.0 - 11.0 11.0 11.0 14.0 14.0 14.0 19.0 19.0 26.5 26.5 26.5 26.5 31.5 31.5 31.5 41.5 - VOLTAGE CODE 63 630 Vdc/250Vac (1) L D (mm) (mm) 6.0 5.5 6.5 7.5 7.0 8.0 9.0 8.5 10.5 12.0 14.5 15.0 18.0 18.0 22.0 - 11 14.0 14.0 14.0 19.0 19.0 19.0 26.5 26.5 26.5 26.5 31.5 31.5 41.5 41.5 - Notes (1) Not suitable for mains applications * Pitch = L + 3.5 mm RECOMMENDED PACKAGING TYPE OF PACKAGING REEL DIAMETER (mm) ORDERING CODE EXAMPLES G Ammo - MKP 1839-422-403-G x R Reel 350 MKP 1839-422-403-R x - Bulk for L > 31.5 mm - MKP 1839-522-403 x PACKAGING CODE Note * For detailed tape specifications refer to "Packaging Information": www.vishay.com/doc?28139 MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to "Packaging Information": www.vishay.com/doc?28139 Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the capacitors body is in good contact with the printed-circuit board. * For L < 19 mm capacitors shall be mechanically fixed by the leads * For larger pitches the capacitors shall be mounted in the same way and the body clamped * The maximum diameter and length of the capacitors are specified in the dimensions table * Eccentricity as shown in the drawing on next page Document Number: 26022 Revision: 16-Jan-09 For technical questions, contact: dc-film@vishay.com www.vishay.com 251 MKP 1839 Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type Space Requirements on Printed-Circuit Board The maximum length and width of film capacitors is shown in drawing: * Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned. * Product height with seating plane as given by IEC 60717 as reference: hmax. h + 0.4 mm or hmax. h' + 0.4 mm 1 mm Storage Temperature * Storage temperature: Tstg = - 25 C to + 40 C with RH maximum 80 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient temperature of 23 C 1 C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % 2 %. For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. CHARACTERISTICS Max. RMS voltage as a function of frequency (typical curve) VRMS 0. Capacitance in F 04 7 0. 1 3 2 1000 7 5 VRMS 100 7 5 Max. RMS voltage as a function of frequency 3 2 0. 22 10 7 5 0. 0. 47 10 6. 4.7 8 01 0. 100 7 5 1. 2.2 Capacitance in F 0 3 02 6. 8 3 2 2 3 5 7 104 5 7 105 3 2 2 3 5 7 106 f (Hz) 3 2 0 0. 3 2 47 2 0. 2 www.vishay.com 252 3 5 7 104 2 2 3 5 7 105 1 5 7 105 3 2 3 2 0. 5 7 106 f (Hz) 3 00 1. 1. 0 5 7 106 f (Hz) 1 00 2 0. 0. 47 0. 22 0. 1 0. 0. 00 04 3 1 Tamb 100 C, 400 Vdc 1 3 10 0. Capacitance in F 100 7 5 2 0. 0 47 0 .2 2 1000 7 5 5 02 1. 47 47 0 .2 2 3 2 0. 01 0. 2 0. 0 Max. RMS voltage as a function of frequency Capacitance in F 2 0. 0 VRMS VRMS 1000 7 5 2. 1. 2 T 100 C, 250 Vdc 1 3amb 5 7 104 2 3 10 Max. RMS voltage as a function of frequency 100 7 5 7 2. 2 Tamb 100 C, 160 Vdc 1 3 10 4. 7 0. 47 02 2 0. 0 1 Tamb 100 C, 630 Vdc 1 3 10 2 3 5 7 104 For technical questions, contact: dc-film@vishay.com 2 3 5 7 105 2 3 5 7 106 f (Hz) Document Number: 26022 Revision: 16-Jan-09 MKP 1839 AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type Vishay Roederstein HEAT CONDUCTIVITY (G) AS A FUNCTION OF ORIGINAL PITCH AND CAPACITOR BODY THICKNESS IN mW/C HEAT CONDUCTIVITY (mW/C) DIAMETER (mm) L 11 mm L 14 mm L 19 mm L 26.5 mm L 31.5 mm L 41.5 mm 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 17.0 17.5 18.0 18.5 19.0 19.5 20.0 20.5 21.0 21.5 22.0 22.5 23.0 23.5 24.0 24.5 25.0 25.5 26.0 26.5 27.0 27.5 28.0 28.5 2 3 3 3 4 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 14 14 15 15 16 17 17 18 19 20 20 21 22 23 23 24 25 26 27 27 28 29 30 31 3 3 4 4 5 5 5 6 6 7 7 8 8 9 10 10 11 11 12 13 13 14 14 15 16 17 17 18 19 19 20 21 22 22 23 24 25 26 27 27 28 29 30 31 32 33 34 35 4 4 5 5 6 7 7 8 8 9 10 10 11 12 12 13 14 14 15 16 16 17 18 19 20 20 21 22 23 24 25 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 5 6 7 7 8 9 10 10 11 12 13 14 14 15 16 17 18 19 20 21 21 22 23 24 25 26 27 28 29 30 31 32 33 35 36 37 38 39 40 41 42 44 45 46 47 48 50 51 6 7 8 9 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 36 37 38 39 41 42 43 44 46 47 48 49 51 52 53 55 56 57 8 9 10 11 12 13 15 16 17 18 19 20 21 23 24 25 26 28 29 30 31 33 34 35 37 38 39 41 42 43 45 46 48 49 50 52 53 55 56 58 59 61 62 64 66 67 69 70 Document Number: 26022 Revision: 16-Jan-09 For technical questions, contact: dc-film@vishay.com www.vishay.com 253 MKP 1839 Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of the free air ambient temperature. The power dissipation can be calculated according type detail specification "HQN-384-01/101: Technical Information Film Capacitors with the typical tgd of the curves". The component temperature rise (T) can be measured (see section "Measuring the component temperature" for more details) or calculated by T = P/G: * T = Component temperature rise (C) * P = Power dissipation of the component (mW) * G = Heat conductivity of the component (mW/C) MEASURING THE COMPONENT TEMPERATURE A thermocouple must be attached to the capacitor body as in: Thermocouple The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC). The temperature rise is given by T = TC - Tamb. To avoid radiation or convection, the capacitor should be tested in a wind-free box. APPLICATION NOTE AND LIMITING CONDITIONS These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference suppression capacitors conforming the standards must be used. To select the capacitor for a certain application, the following conditions must be checked: 1. The peak voltage (UP) shall not be greater than the rated DC voltage (URdc) 2. The peak-to-peak voltage (UP-P) shall not be greater than the maximum (UP-P) to avoid the ionisation inception level 3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URdc and divided by the applied voltage. For all other pulses following equation must be fulfilled: T dU dU 2 2 x -------- x dt < U Rdc x -------- dt rated dt 0 T is the pulse duration. 4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component temperature rise). 5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values mentioned in the table: "Heat conductivity" 6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and surge voltages from the mains included). www.vishay.com 254 For technical questions, contact: dc-film@vishay.com Document Number: 26022 Revision: 16-Jan-09 MKP 1839 AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type Vishay Roederstein Voltage Conditions for 6 Above Tamb 85 C 85 C < Tamb 100 C URac URac Maximum temperature RMS-overvoltage (< 24 h) 1.25 x URac 1.25 x URac Maximum peak voltage (VO-P) (< 2 s) 1.6 x URdc 1.1 x URdc ALLOWED VOLTAGES Maximum continuous RMS voltage INSPECTION REQUIREMENTS General Notes: Sub-clause numbers of tests and performance requirements refer to the "Sectional Specification, Publication IEC 60384-16 and Specific Reference Data". Group C Inspection Requirements SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapter "General Data" of this specification 4.3.1 Initial measurements Capacitance Tangent of loss angle at 100 kHz 4.3 Robustness of terminations Tensile and bending 4.4 Resistance to soldering heat Method: 1A Solder bath: 280 C 5 C Duration: 5 s 4.14 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5 0.5 min Recovery time: Min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 2 % of the value measured initially Tangent of loss angle Increase of tan 0.002 Compared to values measured in 4.3.1 No visible damage SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance Tangent of loss angle: For C 1 F at 10 kHz For C > 1 F at 1 kHz 4.15 Solvent resistance of the marking Isopropylalcohol at room temperature Method: 1 Rubbing material: Cotton wool Immersion time: 5 0.5 min 4.6 Rapid change of temperature A = Lower category temperature B = Upper category temperature 5 cycles Duration t = 30 min Document Number: 26022 Revision: 16-Jan-09 No visible damage Legible marking For technical questions, contact: dc-film@vishay.com www.vishay.com 255 MKP 1839 Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type SUB-CLAUSE NUMBER AND TEST 4.7 CONDITIONS Vibration PERFORMANCE REQUIREMENTS Visual examination Mounting: See section "Mounting" for more information Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s (whichever is less severe) Total duration 6 h No visible damage No visible damage 4.7.2 Final inspection Visual examination 4.9 Shock Mounting: See section "Mounting" for more information Pulse shape: Half sine Acceleration: 490 m/s Duration of pulse: 11 ms 4.9.3 Final measurements Visual examination No visible damage Capacitance |C/C| 2 % of the value measured in 4.6.1 Tangent of loss angle Increase of tan 0.002 Compared to values measured in 4.6.1 Insulation resistance As specified in section "Insulation Resistance" of this specification SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.10 Climatic sequence 4.10.2 Dry heat 4.10.3 Damp heat cyclic Test Db, first cycle 4.10.4 Cold Temperature: Lower category temperature Duration: 2 h 4.10.6 Damp heat cyclic Test Db, remaining cycles Visual examination No visible damage Legible marking Capacitance |C/C| 3 % of the value measured in 4.4.2 or 4.9.3 Tangent of loss angle Increase of tan 0.003 Compared to values measured in 4.3.1 or 4.6.1 Insulation resistance 50 % of values specified in section "Insulation Resistance" of this specification 4.10.6.2 Final measurements Temperature: Upper category temperature Duration: 16 h SUB-GROUP C2 4.11 Damp heat steady state Capacitance 4.11.1 Initial measurements Tangent of loss angle at 1 kHz 4.11.3 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 3 % of the value measured in 4.11.1. Tangent of loss angle Increase of tan 0.001 Compared to values measured in 4.11.1 Insulation resistance 50 % of values specified in section "Insulation Resistance" of this specification SUB-GROUP C3 4.12 Endurance DC Duration: 2000 h 1.25 x URdc at 85 C 0.875 x URdc at 100 C 4.12.1 Initial measurements Capacitance Tangent of loss angle: For C 1 F at 10 kHz For C > 1 F at 1 kHz www.vishay.com 256 For technical questions, contact: dc-film@vishay.com Document Number: 26022 Revision: 16-Jan-09 MKP 1839 AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type SUB-CLAUSE NUMBER AND TEST 4.12.5 Final measurements CONDITIONS Vishay Roederstein PERFORMANCE REQUIREMENTS Visual examination No visible damage Legible marking Capacitance |C/C| 3 % compared to values measured in 4.12.1 Tangent of loss angle Increase of tan 0.002 Compared to values measured in 4.12.1 Insulation resistance 50 % of values specified in section "Insulation Resistance" of this specification Capacitance Capacitance at lower category temperature Capacitance at 20 C Capacitance at upper category temperature For - 55 C to + 20 C: 0 % |C/C| 2 % or for 20 C to 85 C: - 3 % |C/C| 0 % Capacitance Tangent of loss angle: For C 1 F at 10 kHz For C > 1 F at 1 kHz As specified in section "Capacitance" of this specification Insulation resistance As specified in section "Insulation Resistance" of this specification SUB-GROUP C4 4.2.6 Temperature characteristics Initial measurement Intermediate Intermediate measurements Final measurements 4.13 Charge and discharge 10 000 cycles Charged to URdc Discharge resistance: U Rdc R = ---------------------------------------2.5 x C ( dU dt ) 4.13.1 Initial measurements 4.13.3 Final measurements Document Number: 26022 Revision: 16-Jan-09 Capacitance Tangent of loss angle at 100 kHz Capacitance |C/C| 3 % of the value measured in 4.13.1 Tangent of loss angle Increase of tan 0.003 Compared to values measured in 4.13.1 Insulation resistance 50 % of values specified in section "Insulation Resistance" of this specification For technical questions, contact: dc-film@vishay.com www.vishay.com 257 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1