Other conductor
connectors
F.1
F
Other conductor connectors
Overview
F.2 - F.3
For 10 x 3 mm busbars
Clamping yoke F.4 - F.5
Busbarholders F.6 - F.7
Mounting directly on metal plate
Clamping yoke F.8
Busbar holder, Spacer F.9
Mounting on TS 35
FM 4-foot / Clamping yoke holder F.10
For C-profiles
Clamping yoke F.11
Shield connection terminals KLBÜ
Overview
F.18
Junction box terminals
F.19
Lamp terminals
F.20
Euro terminals
F.21
Components for installation
Busbar systems
Busbars, Busbar holders F.22 - F.23
Tension clip, uninsulated / insulated F.24 - F.25
Mounting rail system
Overview F.26 - F.27
Mounting rails TS15, TS 32, TS 35 F.28 - F.29
End holders F.30
Mounting rail supports, Mounting feet F.31
RailMate, mounting rail systems F.32 - F.34
Busbars / mounting rails
For direct mounting
Screw connection F.12 - F.15
Screw connection, ATEX approval F.16 - F.17
Multipin terminal strips
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.1
Shield connection terminals
KLBÜ
F.2
F
The theoretical concept
Part 1 of the VDE 0133 standard specifies the required
equipotential bonding for the electrical components of a ma-
chine. The aim is to prevent any undesirable consequences
occurring as a result of electrostatic, electromagnetic and
mains faults.
The following measures serve this purpose:
• Using filters and delay devices.
• Dividing reference potential into “dirty” and “clean”.
• Neutral earthing of all reference potential with large cross-
section (> 6 mm2).
• Keeping all bonding leads as short as possible.
• Routing all connections parallel to the bonding surface.
• Using screened lines and, if possible, earthing the shield at
both ends.
• Isolating and screening switchgear and components sus-
ceptible to interference.
Overview of the available KLBÜs
For busbars For direct mounting For C-profiles For TS 35 Clip-on for
10 x 3 insulating/conducting 10 x 3 busbar
Control si
g
nal
s
Di
g
ital Analo
g
Position si
g
nal
s
C
N
C
–
G
N
D
C
N
C
–
D
C
ontro
l
t
o
o
th
er
servo am
p
lifier
s
R
ece
iv
er
P
o
w
er
p
ac
k
Nfil
Ne
t
fil
t
er
N
e
tfilt
er
3
˜
X1
X
6
X2
X
5
B
oos
t
e
r
P
C
RE
SO
LVE
R
P
e
r
so
n
al
com
p
ute
r
N
S
T
OP
D
G
N
D
I
/O
ENABLE
BTB
BTB
S
HIEL
D
W
P
E
WP
E
KLB
Ü
KLB
Ü
KLB
Ü
KLB
Ü
KLB
Ü
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.2
Shield connection terminals
KLBÜ
F.3
F
In detail
Compression spring
To ensure both simple handling and proper con-
nection, with permanent contact pressure as a
result of the
spring effect
No extra tools necessary
Simply swivel onto the busbar by hand – ret-
rospectively if necessary
Many options available
Weidmüller offers a wide range of different fas-
tenings for mounting shield connection terminals
Reliable contact
Changes in diameter (flow) of the conductor
compensated for by the elastic behaviour of the
clamping yoke for flexible adjustment to the ca-
ble diameter
Full range
For conductors from 2 to 37 mm diameter
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.3
Shield connection terminals
KLBÜ
F.4
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For 10 x 3 mm busbars
Type for cable diameter Dimensions (a x b x c) mm Qty Order no.
KLBÜ 2 x 2-6 2.0 ... 6.0 mm 15.0 x 18.0 x 24.0 10 1675350000
KLBÜ 3-8 3.0 ... 8.0 mm 13.0 x 18.0 x 26.0 10 1600480000
KLBÜ 4 x 13.5 4.0 ... 13.5 mm 20.0 x 20.5 x 31.5 10 1592810000
KLBÜ 10-20 10.0 ... 20.0 mm 25.0 x 26.0 x 40.0 10 1600490000
KLBÜ 15-32 15.0 ... 32.0 mm 36.0 x 32.0 x 63.9 10 1716300000
10 x 3 mm busbars Length Material Qty Order no.
SSch 10x3x1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
SSch 10x3x1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000
KLBÜOrder data
Clamping yoke
Cable fastened
against the busbar from below
KLBÜ 2x2-6 KLBÜ 3-8 KLBÜ 4-13.5 KLBÜ 10-20 KLBÜ 15 - 32
20
31.5
20.5
a b
c
Marking on the product: T
Marking EN 50019: TEEx e II
Marking EX-RL 94/9/EC: II 2 G D
EC type testing certificate: DMT 02 ATEX E 024 U
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.4
Shield connection terminals
KLBÜ
F.5
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For 10 x 3 mm busbars
Type for cable diameter
Dimensions (a x b x c x d) mm
Qty Order no.
KLBÜ CO 1 3.0 ... 10.0 mm 18.0 x 12.0 x 13.2 x 32.0 10 1753311001
KLBÜ CO 2 4.0 ... 15.0 mm 18.0 x 20.0 x 21.1 x 41.6 10 1752131001
KLBÜ CO 3 10.0 ... 20.0 mm 25.0 x 23.0 x 24.0 x 45.0 10 1749151001
KLBÜ CO 4 15.0 ... 28.0 mm 25.0 x 31.0 x 32.0 x 56.0 10 1749161001
KLBÜ CO 5 20.0 ... 37.0 mm 32.0 x 40.0 x 42.7 x 64.5 10 1755081001
10 x 3 mm busbars Length Material Qty Order no.
SSch 10x3x1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
SSch 10x3x1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000
Clamping yoke
Cable fastened onto
the busbar from above
KLBÜ CO 1 KLBÜ CO 2 KLBÜ CO 3 KLBÜ CO 4 KLBÜ CO 5
23
24
45
24
ac
b
d
KLBÜ CO Order data
Marking on the product: T
Marking EN 50019: TEEx e II
Marking EX-RL 94/9/EC: II 2 G D
EC type testing certificate: DMT 02 ATEX E 024 U
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.5
EC type testing certificate: DMT 02 ATEX E 024 U
Shield connection terminals
KLBÜ
F.6
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For 10 x 3 mm busbars
Type Width Qty Order no.
WSH 1 8.0 mm 10 1068700000
WSH 3/H/N 8.0 mm 10 1715970000
WSH 5 8.0 mm 10 1080100000
WSH 6 8.0 mm 10 1080200000
10 x 3 mm busbars Length Material Qty Order no.
SSch 10x3x1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
Busbar holders
Insulated mounting on TS 35
WSH Order data
Typ WSH 6
Type WSH 3/H/N
Horizontal mounting only
Type WSH 1
Type WSH 5
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.6
Shield connection terminals
KLBÜ
F.7
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For 10 x 3 mm busbars
TS 35 clip Dimensions (l x w x h) mm Qty Order no.
BS 35/WSH 2 52.0 x 37.0 x 13.0 10 1760720000
Busbar connector Dimensions (l x w x h) mm Qty Order no.
BFEH 1/WSH 20.0 x 31.0 x 13.5 10 1082400000
Angle rail Dimensions (l x w x h) mm Qty Order no.
SMSE WSH U1MT 134.0 x 13.0 x 134.0 10 1083900000
Busbar holder sets Contents (parts loose in plastic bag)
BS 35/WSH 2 BFEH 1/WSH SMSE WSH U1MT Qty Order no.
WSH 18 MT 1 ea. 2 ea. 2 ea. 10 1083100000
WSH 19 MT 1 ea. 1 ea. 1 ea. 10 1083200000
WSH 20 MT 1 ea. 1 ea. 1 ea. (straight) 10 1752950000
10 x 3 mm busbars Length Material Qty Order no.
SSch 10x3x1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
SSch 10x3x1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000
Busbar holders
Conductive mounting on TS 35
WSH Order data
EC type testing certificate: DMT 02 ATEX E 024 U
TS 35 Clip Busbar connector Angled rail
BS 35/WSH 2 BFEH 1/WSH SMSE WSH U1MT
Installation example 1
•One busbar
•2 x WSH 19 MT
busbar holder set
Installation example 2
•Two busbars
•2 x WSH 18 MT
busbar holder set
SSB_F001-F034_GB 25.10.2003 10:08 Uhr Seite F.7
Shield connection terminals
KLBÜ
F.8
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Mounting directly on metal plate
Type For cable diameter Thread length
Dimensions (a x b x c x d) mm
Qty Order no.
KLBÜ 3 - 8 SC 3,0 ... 8,0 mm 5,65 mm 13,5 x 11,5 x 18,0 x 26,0 10 1692261001
KLBÜ 4 - 13,5 SC 4,0 ... 13,5 mm 5,30 mm 20,0 x 17,8 x 20,3 x 31,4 10 1712311001
KLBÜ 10 - 20 SC 10,0 ... 20,0 mm 5,30 mm 24,8 x 23,0 x 26,0 x 40,0 10 1712321001
KLBÜ 15 - 32 SC 15,0 ... 32,0 mm 4,80 mm 36,0 x 33,3 x 32,0 x 64,0 10 1718341001
Operating tool Qty Order no.
BTWZ KLBÜ11742630000
KLBÜ SC Order data
Clamping yoke
Marking on the product: T
Marking EN 50019: TEEx e II
Marking EX-RL 94/9/EC: II 2 G D
EC type testing certificate: DMT 02 ATEX E 024 U
KLBÜ 3 - 8 SC KLBÜ 4 - 13,5 SC KLBÜ 10 - 20 SC KLBÜ 15 - 32 SC
22.9
24.8 26
40
aC
b
d
Drilling template KLBÜ 15 – 32 SC
ø 4,2
M 4
10
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.8
Shield connection terminals
KLBÜ
F.9
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
EC type testing certificate: DMT 02 ATEX E 024 U
Mounting directly on metal plate
Busbar holder Qty Order no.
WSH 4 MT 10 1079900000
Type Length Qty Order no.
SP 15 set of 2 15 mm 1 3896100000
SP 20 set of 2 20 mm 1 3896200000
SP 30 set of 2 30 mm 1 3896300000
WSH 4 MT / SP Order data
Busbar holder / Spacer
Busbar holder
Spacer
M6 outer and inner thread
(15 mm, 20 mm and 30 mm long)
Set (WSH 4 MT) consisting of:
–1 busbar holder
–1 busbar connector (BFEH 1/WSH)
ø Du for M 5
ø = 5.2 mm
12
28
40.5
Mounting plate
10 x 3
70
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.9
Shield connection terminals
KLBÜ
F.10
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Mounting on TS 35
FM 4-foot Qty Order no.
FM 4 40 0687900000
Clamping yoke For cable diameter Qty Order no.
BS 35 II without KLBÜ10 1723800000
BS 35 II / KLBÜ 3-8 3.0 ... 8.0 mm 10 1723810000
BS 35 II / KLBÜ 4-13.5 4.0 ... 13.5 mm 10 1723820000
BS 35 II / KLBÜ 3-8/2x2-6 3.0 ... 8.0 mm / 2.0 ... 6.0 mm 10 1749430000
BS 35 II / KLBÜ 2x3-8/2x2-6 3.0 ... 8.0 mm / 2.0 ... 6.0 mm 10 1768020000
FM 4 / BS 35 II Order data
FM 4-foot / Clamping yoke holder
The KLBÜ SC clamping yokes
(see page F.8)
are screwed onto the FM 4 foot.
BS 35 II (without KLBÜ) BS 35 II / KLBÜ 3 - 8 BS 35 II / KLBÜ 3-8 / 2x2-6
FM 4-foot
Clamping yoke holder
Marking on the product: T
Marking EN 50019: TEEx e II
Marking EX-RL 94/9/EC: II 2 G D
EC type testing certificate: DMT 02 ATEX E 024 U
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.10
Shield connection terminals
KLBÜ
F.11
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For C-profiles
Clamping yoke
Type For cable diameter Dimensions (a x b x c x d) mm Qty Order no.
KLBÜ 3 - 8 CPF 3.0 ... 8.0 mm 13.5 x 11.5 x 18.0 x 26.0 10 1752681001
KLBÜ 4 - 13.5 CPF 4.0 ... 13.5 mm 20.0 x 17.8 x 20.3 x 31.4 10 1752691001
KLBÜ 10 - 20 CPF 10.0 ... 20.0 mm 24.8 x 23.0 x 26.0 x 40.0 10 1752701001
KLBÜ 15 - 32 CPF 15.0 ... 32.0 mm 36.0 x 33.3 x 32.0 x 64.0 10 1752711001
C-rail Qty Order no.
TS 27 x 12.5M / ST / F.ZN 10 m 1802690000
KLBÜ CPF Order data
KLBÜ 3 - 8 CPF KLBÜ 4 - 13.5 CPF KLBÜ 10 - 20 CPF KLBÜ 15 - 32 CPF
22.9
24.8 26
40
ac
b
d
Marking on the product: T
Marking EN 50019: TEEx e II
Marking EX-RL 94/9/EC: II 2 G D
EC type testing certificate: DMT 02 ATEX E 024 U
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.11
IEC UL CSA
125 300 300
24 10 10
2.5 24..12 AWG 24..12 AWG
2.5 / 3
A2 / V2
a r
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45
5 mm / M 2.5 / 3.5 x 0.6 mm
Multipin
terminal strips
F.12
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For direct mounting
Width x height / ø fixing hole mm
(length and mounting size: see order data)
Max. clamping range mm2
IEC-60-947-7-1
Technical data
Rating data
Rated voltage V
Rated current A
Rated cross-section mm2
Rated surge voltage / pollution severity kV/-
Plug gauge acc. to IEC 60-947-1/ flammability class UL 94
Approvals
Clamping conductor H05V/H07V)
Solid / stranded mm2
Flexible / flexible with wire end ferrules mm2
Tightening torque range Nm
Stripping length / clamping screw / blade size mm
Notes
Order data
Version
2-pole
3-pole
4-pole
5-pole
6-pole
7-pole
8-pole
9-pole
10-pole
12-pole
14-pole
16-pole
Notes
Accessories
Split rivet
Solder bar
Tag strip
printed
not printed
MK 2/12 2.5 mm2
15.0 x 15.0 / 3.20
0.21 ... 4.0
IEC-60-947-7-1
MK 3/2 ... 12
IEC UL CSA
400 300 300
24 25 25
2.5 22..12 AWG 22..12 AWG
6 / 3
A2 / 5VA
a r
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45
5 mm / M 2.5 / 3.5 x 0.6 mm
2.5 mm2
15.0 x 16.1 / 3.45
0.21 ... 4.0
Type Length/mounting size mm Qty Order no.
MK 3/2 17.40 / 18.5 100 0273820000
MK 3/3 26.50 / 18.5 50 0273920000
MK 3/4 35.75 / 18.5 50 0274020000
MK 3/5 45.00 / 18.5 50 0274120000
MK 3/6 54.25 / 37.0 50 0274220000
MK 3/7 63.50 / 37.0 50 0274320000
MK 3/8 72.75 / 55.5 25 0274420000
MK 3/9 82.00 / 55.5 25 0274520000
MK 3/10 91.25 / 74.0 20 0274620000
MK 3/12 110.00 / 92.5 20 0243520000
Type Qty Order no.
BSTb 28/12 50 0245900000
BSTb 28/8 50 0290200000
BSTb 28/6 50 0290000000
BSTb 28/4 50 0289800000
BSTo 28/12 50 0245800000
BSTo 28/8 50 0284700000
BSTo 28/6 50 0289500000
BSTo 28/4 50 0289300000
Type Length/mounting size mm Qty Order no.
MK 2/12 86.00 / 80.0 50 0241260000
Type Qty Order no.
SN 500 0200100000
MF 2/12 0241760000
BSTb 28/12 bottom 50 0245700000
BSTb 28/12 top 50 0278500000
BSTo 28/12 50 0245600000
Screw connection
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.12
Multipin
terminal strips
F.13
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
IEC UL CSA
690 300 300
41.0 30 40
6.0 22...10 AWG 22..10 AWG
8 / 3
A3 / V2
a r
0.5...6 / 1.5....6
0.5...6 / 0.5...4
1.2...2.0
9 mm / M 4 / 4.0 x 0.8 mm
IEC-60-947-7-1
MK 6/2 ... 6/6 6.0 mm2
23 x 22 / 3.4
0.33 ... 6.0
IEC-60-947-7-1
MK 10/14
IEC UL CSA
125 150 300
24 25 10
2.5 22...12 AWG 24...12 AWG
2.5 / 3
A2 / V2
a r
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45
6 mm / M 2.5 / 3.5 x 0.6 mm
Mounted by gluing or with M3x12 screws. Through the empty terminal point chamber
2.5 mm2
13.5 x 12 / 3.1
0.21 ... 4.0
Type Length/mounting size mm Qty Order no.
MK 10/14 88.5 / - 20 0370160000
Other pole numbers available on request
Type Qty Order no.
Type Length/mounting size mm Qty Order no.
MK 6/2 23.5 / - 50 0620420000
MK 6/3 36.5 / 13.0 50 0620320000
MK 6/4 49.5 / 26.0 20 0620220000
MK 6/6 75.5 / 52.0 20 0620120000
Type Qty Order no.
BSTb 28/6 50 0304600000
IEC UL CSA
400 150 150
24 20 15
2.5 22..12 AWG 22..12 AWG
6 / 3
A2 / 5VA
a r
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45
8 mm / M 2.5 / 3.5 x 0.6 mm
IEC-60-947-7-1
MK 4/16 2.5 mm2
17.0 x 16.0 / 3.40
0.21 ... 4.0
Type Length/mounting size mm Qty Order no.
MK 4/16 103.00 / 85.5 20 0244220000
Type Qty Order no.
BSTb 28/16 unten 50 0262200000
BSTb 28/16 oben 50 0278700000
BSTo 28/16 50 0262100000
For direct mounting
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.13
Multipin
terminal strips
F.14
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
IEC UL CSA
500
24
2.5
6 / 3
A2 / 5 VA
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45
5 mm / M 2.5 / 3.5 x 0.6 mm
For direct mounting
Width x height / ø fixing hole mm
(length and mounting size: see order data)
Max. clamping range mm2
Technical data
Rating data
Rated voltage V
Rated current A
Rated cross-section mm2
Rated surge voltage / pollution severity kV/-
Plug gauge acc. to IEC 60-947-1/ flammability class UL 94
Approvals
Clamping conductor H05V/H07V)
Solid / stranded mm2
Flexible / flexible with wire end ferrules mm2
Tightening torque range Nm
Stripping length / clamping screw / blade size mm
Notes
Order data
Version
2-pole
3-pole
4-pole
5-pole
6-pole
7-pole
8-pole
9-pole
10-pole
12-pole
14-pole
16-pole
Notes
Accessories
Split rivet
Cover
D2 D4
Tag strip
printed
not printed
MK 5/2 o. DE 2.5 mm2
18.0 x 14.2 / 4.2
0.21 ... 4.0
KS 2 ... 10
IEC UL CSA
500 300 300
24 20 25
2.5 22..12 AWG 24...12 AWG
6 / 3
A2 / 5VA
a r
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.5...0.7
8 mm / M 3 /4.0 x 0.8 mm
2.5 mm2
25.0 x 17.5 / 4.2
0.21 ... 4.0
Type Length/mounting size mm Qty Order no.
KS 2 42 / 32 100 0134420000
KS 4 66 / 56 50 0140320000
KS 6 90 / 80 50 0140620000
KS 10 138 / 128 20 0141620000
Type Qty Order no.
D2 KS2 TP 100 0134500000
D4 KS4 TP 50 0140500000
D6 KS6 TP 50 0140800000
D10 KS 10 TP 20 0141800000
ELSb 2 50 0143200000
ELSb 4 50 0143300000
ELSb 6 50 0143400000
ELSb 10 50 0143500000
ELSo 2 50 0142800000
ELSo 4 50 0142900000
ELSo 6 50 0143000000
ELSo 10 50 0143100000
Type Length/mounting size mm Qty Order no.
MK 5/2 40 / 32 100 0243820000
Type Qty Order no.
D2 MK 5/2 0244060000
Screw connection
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.14
Multipin
terminal strips
F.15
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
IEC UL CSA
400 300 300
32.0 10 10
4.0 22..12 AWG 22..12 AWG
6 / 3
A3 / 5VA
a r
0.5...4 / 1.5...4
0.5...4 / 0.5...4
0.5...0.7
8 mm / M 3 / 4.0 x 0.8 mm
BK 2...12 4.0 mm2
22 x 20 / 3.40
0.33 ... 4.0
Type Length/mounting size mm Qty Order no.
BK 2CRN 20 / - 100 0624720000
BK 3CRN 31 / 11.0 100 0624920000
BK 4CRN 38 / 18.0 100 0625120000
BK 6CRN 52 / 32.0 50 0625220000
BK12 CRN 92 / 72.5 25 0625320000
Type Qty Order no.
SN 500 0200100000
BSTb 28/2 50 0203600000
BSTb 28/3 50 0203800000
BSTb 28/4 50 0197300000
BSTb 28/6 50 0197500000
BSTb 28/12 50 0198800000
BSTo 28/2 50 0203500000
BSTo 28/3 50 0203700000
BSTo 28/4 50 0197200000
BSTo 28/6 50 0197400000
BSTo 28/12 50 0198700000
For direct mounting
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.15
Multipin
terminal strips
F.16
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
For direct mounting
Width x height / ø fixing hole mm
(length and mounting size: see order data)
Max. clamping range mm2
Technical data
Rating data
Rated voltage V
Rated current A
Rated cross-section mm2
Rated surge voltage / pollution severity kV/-
Plug gauge acc. to IEC 60-947-1/ flammability class UL 94
Approvals
Clamping conductor H05V/H07V)
Solid / stranded mm2
Flexible / flexible with wire end ferrules mm2
Tightening torque range Nm
Stripping length / clamping screw / blade size mm
Notes
Order data
Version
2-pole
3-pole
4-pole
5-pole
6-pole
7-pole
8-pole
9-pole
10-pole
11-pole
12-pole
Notes
Accessories
Split rivet
Tag strip
printed
not printed
Screw connection
ATEX approval
IEC UL CSA EN 50019
400 300 300 275
32.0 10 10 21
4.0 22 ...2 AWG 22 ...12 AWG 4.0
6 / 3
A3 / 5VA
a r BAS 98ATEX3084 U
0.5...4 / 1.5...4
0.5...4 / 0.5...4
0.5...0.7
8 mm / M 3 / 4.0 x 0.8 mm
BK 2...12/E 4.0 mm2
22 x 20 / 3.40
0.33 ... 4.0
Type Length/mounting size mm Qty Order no.
BK 2/E 20 / - 100 7906040000
BK 3 /E 31 / 11.0 100 7906060000
BK 4 /E 38 / 18.0 100 7906080000
BK 6 /E 52 / 32.0 50 7906090000
BK 12/E 92 / 72.5 25 7906100000
Type Qty Order no.
SN 500 0200100000
BSTb 28/2 50 0203600000
BSTb 28 /3 50 0203800000
BSTb 28/4 50 0197300000
BSTb 28/6 50 0197500000
BSTb 28/12 50 0198800000
BSTo 28/2 50 0203500000
BSTo 28/3 50 0203700000
BSTo 28/4 50 0197200000
BSTo 28/6 50 0197400000
BSTo 28/12 50 0198700000
IEC UL CSA EN 50019
400 300 300 275
24 25 25 15
2.5 22 ...12 AWG 22 ...12 AWG 2.5
6 / 3
A2 / 5VA
a r BAS 99ATEX2124 U
0.5...4 / 1.5...2.5
0.5...2.5/ 0.5...1.5
0.4...0.6
5 mm / M 2.5/ 3.5x 0.6 mm
MK 3/2...12/E 2.5 mm2
15 x 16.1 x 3.45
0.21 ....4
Type Length/mounting size mm Qty Order no.
MK 3/2/E 17.40 / 18.50 100 7906110000
MK 3/3 E 26.50 / 18.50 100 7906120000
MK 3/4/E 35.75 / 18.50 50 7906130000
MK 3/5/E 45.00 / 18.50 50 7906140000
MK 3/6/E 54.25 / 37.00 50 7906150000
MK 3/7/E 63.50 / 37.00 25 7906160000
MK 3/8/E 72.75 / 55.50 25 7906170000
MK 3/9/E 82.00 / 55.50 25 7906180000
MK 3/10/E 91.25 / 74.00 25 7906190000
MK 3/11/E 100.50 / 74.00 25 7906200000
MK 3/12/E 110.00 / 92.50 25 7906210000
Type Qty Order no.
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.16
Multipin
terminal strips
F.17
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
IEC UL CSA EN 50019
690 300 300 420
41.0 30 40 26
6.0 22..10 AWG 22..10 AWG 6.0
8 / 3
A3 / V0
a r BAS 99ATEX2123 U
0.5...6 / 1.5...6
0.5...6 / 0.5...4
1.2...2.0
9 mm / M 4 / 4.0 x 0.8 mm
MK 6/2 ... 6/E 6.0 mm2
23 x 22 / 3.40
0.21 ... 6
Type Length/mounting size mm Qty Order no.
MK 6/2/E 23.50 / - 50 7906220000
MK 6/3/E 36.50 / 13.00 50 7906230000
MK 6/4/E 49.50 / 26.00 20 7906240000
MK 6/5/E 62.50 / 26.00 20 7906250000
MK 6/6/E 75.50 / 52.00 20 7906260000
Type Qty Order no.
BSTb 28/6 50 0304600000
For direct mounting
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.17
Components
for installation
F.18
F
Installation terminals for electrical installation in buildings
Junction box terminals
•Suitable for rigid conductors
•Connect: strip conductor and push into
terminal opening – that's all there is to it!
•Disconnect: unscrew ends of conduc-
tors and terminals from each other and
pull apart at the same time.
Europa terminals
•Suitable for rigid and flexible conductors
•Simply divide the 12-pole strip into parts
with differing pole numbers.
Lighting terminals
•On the “installation side”: suitable for
two rigid conductors. The conductor
can be looped on
•Within the lamp: suitable for flexible con-
ductor which connects the lamp
•Strip rigid conductor and push into con-
tact opening. Strip flexible wire and
press rocker to open the clamping
spring. Push end of conductor in and re-
lease rocker.
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.18
Components
for installation
F.19
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Junction box terminals
D-series
Screwless installation terminals
Material
Enclosure Polyamide PA 66, pale grey RAL 7035
Busbar Coated electrolyte copper
Connection values EN 60998 UL 486C for aluminium conductors 1)
D1.5/2.5: 450V / 25 A 600V / 20 A 450V / 16A
D4.0 450V / 35 A 600V / 30 A 450V / 22A
Temperature range
When using copper conductors –40 °C .. +100 °C
When using aluminium conductors 1)–40 °C .. +60 °C
Approvals
m i y x z t s q # ! ] \ % @
1) when using Alu-Top 30 contact paste
Technical data
In box Terminal points Clamping range Qty (in box) Order no.
D1.5/2.5-2 2 0,75 - 2,5 mm2(AWG 18 - 14) sol 100 1746420000
D1.5/2.5-3 3 0,75 - 2,5 mm2(AWG 18 - 14) sol 100 1746430000
D1.5/2.5-4 4 0,75 - 2,5 mm2(AWG 18 - 14) sol 100 1746440000
D1.5/2.5-5 5 0,75 - 2,5 mm2(AWG 18 - 14) sol 100 1746450000
D1.5/2.5-8 8 0,75 - 2,5 mm2(AWG 18 - 14) sol 50 1746460000
D4.0-3 3 1,50 - 4,0 mm2(AWG 15 - 12) sol 50 1746470000
In bag Terminal points Clamping range Qty (in bag) Order no.
D-Pack D1.5/2.5-2 2 0,75 - 2,5 mm2(AWG 18 - 14) sol 25 1781450000
D-Pack D1.5/2.5-3 3 0,75 - 2,5 mm2(AWG 18 - 14) sol 25 1781460000
D-Pack D1.5/2.5-4 4 0,75 - 2,5 mm2(AWG 18 - 14) sol 25 1781470000
D-Pack D1.5/2.5-5 5 0,75 - 2,5 mm2(AWG 18 - 14) sol 25 1781480000
D-Pack D1.5/2.5-8 8 0,75 - 2,5 mm2(AWG 18 - 14) sol 20 1781490000
D-Pack D4.0-3 3 1,50 - 4,0 mm2(AWG 15 - 12) sol 20 1781500000
Accessories Qty Order no.
Alu-Top 30 (contact paste) 51778260000
Sample bag 11804420000
Order data
Alu-Top 30
•For connecting solid copper conductors
using the direct push-in technique
•Extremely easy to push in
•Just one size covers all cross-sectional
areas from 0.75 to 2.5 mm2
•Additional size for conductors up to
4 mm2
•2 to 8 contact points
•Conductors disconnected by turning
and pulling
•For aluminium conductors, we recom-
mend using Alu-Top 30 a contact paste
•Test opening for voltage tester
•Grooves on the bottom to show the re-
quired stripping length
•Approvals based on DIN EN 60998 and
UL 486C
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.19
Components
for installation
F.20
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Lamp terminals
Screwless installation terminals
for solid and flexible conductors
Material
Enclosure Polyamide PA 66, pale grey RAL 7035
Busbar Tin-coated electrolyte copper
Clamping range
Installation side 2 x 1,0 - 2,5 mm2(AWG 17 - 14) solid copper conductor
Lamp side 1 x 0,5 - 2,5 mm2(AWG 20 - 14) flexible copper conductor
Connection values
Rated current/voltage 24 A / 400 V
Rated surge voltage 4 kV
Pollution severity 2
Temperature range
Temperature in constant use +105 °C acc. to UL 746B
Ambient temperature –40 °C .. +60 °C
Approvals
m i y x z t s q # ! ] \ % @
Technical data
In box Qty (in box) Order no.
D-Lux 2/1 100 1774270000
In bag Qty (in bag) Order no.
D-Pack D-Lux 2/1 25 1791260000
Order data
•Fast, easy and safe installation of lamps
•Detachable connection, without tools
•2 solid conductors connected on the in-
stallation side
•One flexible conductor connected on
the lamp side
•Spring contact for screwless connection
•Test opening for voltage tester
•Minimal space requirement
Stranded conductors strip
(8–9 mm) conductor,
compress terminal and
insert conductor
Solid conductor strip
(8–9 mm) and
connect conductor
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.20
Components
for installation
F.21
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Euro terminals
Screw connection
Polyamide, natural Nominal cross-section mm2Max. conductor cross-section mm2Qty. Order no.
D-Strip 2.5-4/12 PA 2.5 4.0 10 1837100000
D-Strip 4-6/12 PA 4.0 6.0 10 1837130000
D-Strip 6-10/12 PA 6.0 10.0 10 1837160000
D-Strip 16/12 PA 16.0 16.0 10 1837190000
D-Strip 25/12 PA 25.0 25.0 10 1837220000
Polyethylene, black
D-Strip 2.5-4/12 PE B 2.5 4.0 10 1837110000
D-Strip 4-6/12 PE B 4.0 6.0 10 1837140000
D-Strip 6-10/12 PE B 6.0 10.0 10 1837170000
D-Strip 16/12 PE B 16.0 16.0 10 1837200000
D-Strip 25/12 PE B 25.0 25.0 10 1837230000
Polyethylene, white
D-Strip 2.5-4/12 PE W 2.5 4.0 10 1837120000
D-Strip 4-6/12 PE W 4.0 6.0 10 1837150000
D-Strip 6-10/12 PE W 6.0 10.0 10 1837180000
D-Strip 16/12 PE W 16.0 16.0 10 1837210000
D-Strip 25/12 PE W 25.0 25.0 10 1837240000
Order data
Material Polyamide (natural) Polyethylene (black or white)
Inserts Chromated brass Brass
Screws Chromated steel Chromated steel
Rated voltage
D-Strip 2.5-4/12 to D-Strip 16/12 450 V 450 V
D-Strip 25/12 750 V 750 V
Temperature range
Ambient temperature +85 °C / +110 °C 1) +85 °C
max. testing temperature acc. to EN 60998 +115 °C / +140 °C 1)-
Approvals
m i y x z t s q # ! ] \ % @
1) for D-strip 16/12 PA and D-strip 25/12 PA
Technical data
•12-pole terminal strip for conductor
cross-sectional areas up to 25 mm2
•Insulating material: choice of polyamide
or polyethylene
•Captive screws, screwed up in delivery
condition
•Various international approvals
Dimensions in mm
Type A B C D E F
D-Strip 2.5-4... 93.6 16.2 13.4 8.0 ø 2.8 ø 2.8
D-Strip 4-6... 116.4 18.6 15.0 10.0 ø 3.6 ø 3.5
D-Strip 6-10 133.5 22.2 17.3 11.5 ø 4.2 ø 3.6
D-Strip 16... 175.0 25.2 20.8 15.0 ø 5.8 ø 5.2
D-Strip 25... 212.0 36.0 29.6 18.0 ø 7.5 ø 4.0
SSB_F001-F034_GB 25.10.2003 10:09 Uhr Seite F.21
Busbars /
mounting rails
F.22
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Busbar systems
Type Material Cross-section Length Current carrying capacity Qty Order no.
SSch 10x3 Copper, tin-plated 10 x 3 mm 1 m 140 A 1 0348900000
SSch 10x3 Steel, galvanised 10 x 3 mm 1 m 1 0438000000
SSch 10x3 Brass, bright 10 x 3 mm 1 m 100 A 1 0259800000
SSch 6x6 Copper, tin-plated 6 x 6 mm 1 m 140 A 1 0571300000
SSch 6x6 Brass, bright 6 x 6 mm 1 m 100 A 1 0571200000
SSch 15x6 Copper, tin-plated 15 x 6 mm 1 m 265 A 1 0357400000
Busbars, unperforated SSch
Type Material Cross-section Length Power Rating Qty Order no.
NSch 15x2 Copper, bright 15 x 2 mm 1 m 80 A 1 0280200000
ESch 12x2 Steel, galvanised 12 x 2 mm 1 m 1 0280300000
Pressure piece Qty Order no.
DKSUE 100 0280100000
Clamping screw Qty Order no.
BFSC M5x8 100 0296700000
Busbars, perforated NSch / ESch
In switchgears and controls, it may be necessary
to bring the neutral conductor and the protective
conductor together at a central point. Busbars are
available for this purpose and can be used for con-
necting a large number of conductors in a con-
fined space (up to 70 conductors on a 1 m bus-
bar). The conductors are connected by means of a
pressure piece or tension clamp; the former does
not entail bending the eyelets. A guide lug on the
pressure piece engages in the busbar and holds
the pressure piece firmly so that it cannot twist.
The tension clamps can be pushed on the busbar
and adjusted to the entire wiring in the system.
The busbars can be used unperforated in any
lengths. They are fixed using the SH busbar holder
which can, for longer busbars, also be positioned
between the tension clamps.
Connection data NSch/ESch
Screw connection solid 0.5 ... 2.5 mm2
Stripping length 9 mm
Cable lug connection max. 16 mm2
Max. current per connection 27 A
Busbars Tension clamps (see page F.24 – F.25)
In order to bring together neutral conductors and
protective conductors at a central point, it is ad-
vantageous to use ZB tension clamps together
with 10 x 3 or 6 x 6 busbars. The tension clamps
can be pushed onto the busbar and adjusted to
the entire wiring in the system.
The tension clamp serves as the protective con-
ductor connection and can be supplied with
green/yellow insulating caps. These caps indicate
the protective function and marking tags allow
clear identification of each conductor.
If the tension clamps are used to connect neutral
conductors, they can be marked with a blue insu-
lating cap.
ZBE6 can also be swivelled onto the busbar retro-
spectively.
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.22
Busbars /
mounting rails
F.23
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Busbar systems
Busbar holders
Type For busbar cross-section Qty. Order no.
SH 1 TS 15 complete 10x3, 6x6, 15x2, 12x2 20 0299860000
Individual parts SH1
SH 1 base 20 0401460000
SH 1 clip 500 0635960000
Fixing screw for SH2
BFSC M4x9 for 1 SH1 100 0103300000
BFSC M4x30 for 2 SH1 stacked 50 0267100000
With clip and base
SH
Type For busbar cross-section Qty. Order no.
SH 2S 10x3, 6x6, 15x6, 10x5 10 0641720000
With metal bridge
Clip
Base
Busbar holders
Type For busbar cross-section Qty. Order no.
WEW 35/1 10x3, 6x6 50 1059000000
WEW 35/2 10x3, 6x6 100 1061200000
WEW
Type For busbar cross-section Qty. Order no.
SH 3 10x3, 6x6, 10x5 10 0556660000
With metal bridge
Connection element
Type For busbar cross-section Qty. Order no.
AK 95 15 x 6 mm 10 0364200000
The AK95 connection element is used as a tension clamp for 15 x 6 busbars
Connection cross-sections e = 6…16 mm2
f=6…50 mm2
m=16…50 mm2
AK 95
WEW 35/1 and WEW35/2 as
busbar holder together with the
ZB 4 G tension clamp
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.23
Busbars /
mounting rails
F.24
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Tension clip, uninsulated
Busbar systems
Type Colour Dimensions [mm] Qty Order no.
a width c h1
ZB 4, bright - 11.7 5.6 16.0 10.0 50 0316500000
Insulating cap Blue 50 0475480000
Insulating cap Green/yellow 50 0475460000
ZBE 6, bright - 19.5 8.2 19.5 19.0 50 0459500000
Insulating cap Blue 50 0526080000
Insulating cap Green/yellow 50 0526060000
ZB 10, bright - 19.5 8.2 19.5 19.0 50 1261300000
ZB 16, bright - 17.0 10.0 16.0 17.0 50 0316600000
Insulating cap Blue 50 0502980000
Insulating cap Green/yellow 50 0502960000
ZB 35, bright - 21.0 14.4 18.4 20.5 20 0266500000
Insulating cap Blue 50 0502780000
Insulating cap Green/yellow 50 0502760000
Connection cross-section:
Solid 0.5 ... 6.0 mm2
Flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
For swivelling on retrospectively
Connection cross-section:
Solid 1.0 ... 10 mm2
Flexible 1.5 ... 10 mm2
Stranded -
Clamping screw M 4
Stripping length 19 mm
Also for busbar 10 x 5 mm available
Connection cross-section:
Solid 1.5 ... 10 mm2
Flexible 2.5 ... 10 mm2
Stranded -
Clamping screw M 4
Stripping length 19 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 16 mm
Connection cross-section:
Solid -
Flexible 16 ... 35 mm2
Stranded 16 ... 50 mm2
Clamping screw M 6
Stripping length 19 mm
ZB / ZBE
Type Colour Dimensions [mm] Qty Order no.
a width c h1
ZB 4/6, bright 14.7 5.6 12.5 10.0 50 0556700000
Insulating cap Blue 50 0565380000
ZB 16/6, bright 19.0 10.0 12.5 17.0 50 0556800000
Insulating cap Blue 50 0565580000
Insulating cap Green/yellow 50 0565560000
Connection cross-section:
Solid 0.5 ... 6.0 mm2
flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 12 mm
ZB
For 10 x 3 mm busbars
For 6 x 6 mm busbars
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.24
Busbars /
mounting rails
F.25
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Type Colour Dimensions [mm] Qty Order no.
a2 width d h2
ZB 4 G GN/GE Green/yellow 27.0 7.6 19.7 15.5 50 0322160000
ZB 4 G BL Blue 27.0 7.6 19.7 15.5 50 0322180000
ZB 4 G SW Black 27.0 7.6 19.7 15.5 50 0322110000
ZB 4K GN/GE Green/yellow 18.5 6.0 19.0 13.0 50 0475360000
ZB 4K BL Blue 18.5 6.0 19.0 13.0 50 0475380000
ZBE 6K GN/GE Green/yellow 27.0 8.0 22.5 23.0 50 0525960000
ZBE 6K BL Blue 27.0 8.0 22.5 23.0 50 0525980000
ZBE 6K SW Black 27.0 8.0 22.5 23.0 50 0525910000
ZB 16K GN/GE Green/yellow 24.0 10.0 19.2 20.0 50 0502860000
ZB 16K BL Blue 24.0 10.0 19.2 20.0 50 0502880000
ZB 16K SW Black 24.0 10.0 19.2 20.0 50 0502810000
ZB 35K GN/GE Green/yellow 25.0 14.4 32.0 20.5 20 0502660000
ZB 35K BL Blue 25.0 14.4 32.0 20.5 20 0502680000
ZB 35K SW Black 25.0 14.4 32.0 20.5 20 0502610000
ZF 4 S Beige 22.0 6.1 24.5 - 50 1814680000
ZF 4 S BL Blue 22.0 6.1 24.5 - 50 1814660000
ZF 4 S GN/GE Green/yellow 22.0 6.1 24.5 - 50 1814670000
Connection cross-section:
Solid 0.5 ... 6.0 mm2
Flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
For swivelling on retrospectively
Connection cross-section:
Solid 1.0 ... 10 mm2
Flexible 1.5 ... 10 mm2
Stranded -
Clamping screw M 4
Stripping length 19 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 16 mm
Connection cross-section:
Solid -
Flexible 16 ... 35 mm2
Stranded 16 ... 50 mm2
Clamping screw M 6
Stripping length 19 mm
Tension spring connection
Connection cross-section:
Solid 0.5 ... 4.0 mm2
Flexible 0.5 ... 2.5 mm2
Stranded -
Stripping length 10 mm
ZB / ZBE / ZF
Type Colour Dimensions [mm] Qty Order no.
a2 width d h2
ZB 4/6K GN/GE Green/yellow 21.2 6.0 25.0 14.0 50 0565460000
ZB 4/6K BL Blue 21.2 6.0 25.0 14.0 50 0565480000
ZB 16/6K GN/GE Green/yellow 26.0 9.7 25.0 20.0 50 0569660000
ZB 16/6K BL Blue 26.0 9.7 25.0 20.0 50 0569680000
Connection cross-section:
Solid 0.5 ... 6.0 mm2
Flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 12 mm
ZB
For busbars 10 x 3 mm
Tension clamp, insulated
For 6 x 6 mm busbar
Busbar systems
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.25
Busbars /
mounting rails
F.26
F
Both active and passive components and intelligent modules
are mounted on mounting rails – a method which has proven
its worth over the years. But it is only after the use of certain
consumables – which are frequently not taken into considera-
tion – that electrical installation is finally completed. In this
chapter, users will find a range of mounting rails and profile
rails for component installation together with end holders for
holding and isolating the components. This guarantees firm in-
stallation and isolation. Weidmüller supplies components
which show perfect functional compatibility.
Mounting rails are made of either steel, stainless steel, alumini-
um or copper, depending on the area of application.
Stainless steel
Stainless steel is a collective noun for all kinds of steel (alloys)
which are smelted in a special process and have a high de-
gree of purity. Stainless steel has much-enhanced resistance
to corrosion. Weidmüller's stainless steel mounting rails have
the following composition: X5 CrNi 18-10 stainless steel (i.e. ~
18% chromium, ~ 10% nickel).
Aluminium
Aluminium is second only to copper in its electrical conductivi-
ty. One advantage is its light weight. Aluminium oxidises quick-
ly in air; thus passivated, it offers excellent corrosion protec-
tion.
Copper
Copper, a heavy metal, has the best electrical conductivity of
all metals used. As it is a soft metal, Weidmüller's mounting
rails are 2.3 mm thick.
Steel
All steel versions are galvanised and also passivated with a
chromate layer, differentiated into yellow (chromium VI) and
blue chromate (chromium III). Blue chromating has been intro-
duced because of future restrictions on chromium (VI) com-
pounds.
Mounting rails, profile rails, end holders
All mounting rails are produced in 1 m and 2 m lengths.
A mounting rail can also be used as a protective conductor
busbar. Weidmüller PE / earth terminals in the W series, Z se-
ries, I series, SAK and AKZ series comply with requirements
stipulated in IEC 60 947-7-2. According to VDE 0100 part 540,
for conductors with cross-sectional areas exceeding 10 mm2,
both protective and neutral conductors may be grouped to-
gether as a single category of conductors designated PEN.
If a mounting rail is used as a PEN busbar, the following criteria
must be observed:
•Only E-Cu or aluminium profiles are allowed
•Short-circuit currents and thermal rated currents must be
taken into account
•The mounting rails are to be insulated as a contribution to
protective insulation
All unperforated mounting rails can be provided with fixing
holes (state dimensions b and l2).
Possible diameters are 3.5 / 5.6 / 5.5 / 7 mm.
All unperforated steel rails can also be supplied with welded on
steel studs (state dimension a and required studs).
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.26
Busbars /
mounting rails
F.27
F
TS 35 W
Mounting rails
TS 32 Y
TS 15 U
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.27
Busbars /
mounting rails
F.28
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Mounting rail systems
TS15 mounting rail U
Unperforated Aluminium, bright Short-circuit strength Material thickness Length Qty Order no.
TS 15x5 2M/AL/BK 16 mm21 mm 2 m 10 m 0134700000
(max. tolerable rated current for PEN function = 76 A)
Steel, galvanised / yellow passivated
TS 15x5 2M/ST/ZN 10 mm21 mm 2 m 2 m 0514200000
TS 15x5 1M/ST/ZN 10 mm21 mm 1 m 10 m 0514210000
With slatted hole Aluminium, bright Short-circuit strength Material thickness Length Qty Order no.
TS 15x5/LL 2M/AL/BK 16 mm21 mm 2 m 2 m 0217900000
(max. tolerable rated current for PEN function = 76 A)
Steel, galvanised / yellow passivated
TS 15x5/LL 2M/ST/ZN 10 mm21 mm 2 m 2 m 0117500000
TS 15x5/LL 1M/ST/ZN 10 mm21 mm 1 m 10 m 0117510000
TS 15 x 5
TS 32 mounting rail Y
Unperforated Aluminium, bright Short-circuit strength Material thickness Length Qty Order no.
TS 32X15 2M/AL/BK 70 mm21,5 mm 2 m 2 m 0169300000
(max. tolerable rated current for PEN function = 192 A)
Steel, galvanised / yellow passivated
TS 32X15 2M/ST/ZN 35 mm21,5 mm 2 m 2 m 0122800000
TS 32X15 1M/ST/ZN 35 mm21,5 mm 1 m 10 m 0122810000
Copper, bright
TS 32X16.2 2M/CU/BK 120 mm22,1 mm 2 m 2 m 0364300000
(max. tolerable rated current for PEN function = 269 A
Stainless steel, bright
TS 32X15 2M/CRN 35 mm21,5 mm 2 m 2 m 0293220000
With slatted hole
Steel, galvanised / yellow passivated
Short-circuit strength Material thickness Length Qty Order no.
TS 32X15/LL 2M/ST/ZN 35 mm21,5 mm 2 m 2 m 0514400000
TS 32X15/LL 1M/ST/ZN 35 mm21,5 mm 1 m 10 m 0514410000
TS 32 x 15
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.28
Busbars /
mounting rails
F.29
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Unperforated
Mounting rail systems
Aluminium, bright Short-circuit strength Material thickness Length Qty Order no.
TS 35X7.5 2M/AL/BK 35 mm21 mm 2 m 2 m 0330800000
(max. tolerable rated current for PEN function = 125 A)
Steel, galvanised / yellow passivated
TS 35X7.5 2M/ST/ZN 16 mm21 mm 2 m 2 m 0383400000
TS 35X7.5 1M/ST/ZN 16 mm21 mm 1 m 10 m 0383410000
Stainless steel, bright
TS 35X7.5 2M/CRN 16 mm21 mm 2 m 2 m 1747350000
With slatted hole
Steel, galvanised / yellow passivated
Short-circuit strength Material thickness Length Qty Order no.
TS 35X7.5/LL 2M/ST/ZN 16 mm21 mm 2 m 2 m 0514500000
TS 35X7.5/LL 1M/ST/ZN 16 mm21 mm 1 m 10 m 0514510000
Steel, galvanised / blue passivated
TS 35X7.5/LL 2M/ST/ZN /WS/BL 16 mm21 mm 2 m 2 m 0514580000
TS 35 x 7,5
TS 35 mounting rail W
Unperforated Copper, bright Short-circuit strength Material thickness Length Qty Order no.
TS 35X15/2.3 2M/CU/BK 150 mm22.3 mm 2 m 2 m 0270100000
(max. tolerable rated current for PEN function = 309 A)
Steel, galvanised / yellow passivated
TS 35X15/2.3 2M/ST/ZN 50 mm22.3 mm 2 m 2 m 0498000000
Aluminium, bright
TS 35X15/2.3 2M/AL/BK 70 mm22.3 mm 2 m 2 m 1848290000
(max. tolerable rated current for PEN function = 192 A)
Unperforated
Steel, galvanised / yellow passivated
Short-circuit strength Material thickness Length Qty Order no.
TS 35X15 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 0236400000
TS 35X15 1M/ST/ZN 25 mm21.5 mm 1 m 10 m 0236410000
TS 35 x 15
Unperforated PVC RAL 7035 Length Qty Order no.
TSK 35X15 2M PVC/GR 2 m 2 m 0514300000
TSK 35 x 15
With slatted hole
Steel, galvanised / yellow passivated
Short-circuit strength Material thickness Length Qty Order no.
TS 35X15/LL 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 0236500000
TS 35X15/LL 1M/ST/ZN 25 mm2 1.5 mm 1 m 10 m 0236510000
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.29
Busbars /
mounting rails
F.30
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Mounting rail systems
End holders
Polyamide 66, screwable Colour Torque Qty Order no.
EWK AKA 2.5 Beige 0.4 Nm 50 0348660000
EW 15 Beige 0.4 Nm 50 0382860000
Polyamide with fibreglass, screwable
EW 15/2 Dark beige 0.4 Nm 50 1071900000
Polyamide 66, screwless
ZEW 15 Beige - 20 7920340000
For TS 15 mounting rail
Polyamide 66, screwable Colour Torque Qty Order no.
EWK 2 Beige 1.2 Nm 50 0199360000
EWK 1 TS 32 M4X18 Beige 1.2 Nm 50 0206160000
EWK 1 ALT Beige 0.6 Nm 50 0495160000
Polyamide with fibreglass, screwable
WEW 32/1 Dark beige 0.5 Nm 50 1067600000
For mounting rail TS 32
Polyamide 66, screwable Colour Torque Qty Order no.
EW 35 GR Grey 0.5 Nm 50 0383530000
EW 35 Beige 0.5 Nm 50 0383560000
Polyamide with fibreglass, screwable
WEW 35/1 Dark beige 1.2 Nm 50 1059000000
WEW-35/2 Dark beige 0.5 Nm 100 1061200000
Polyamide 66, screwless
ZEW Beige - 20 9540000000
ZEW 35/2 Beige - 20 8630740000
For mounting rail TS 35
8
width: ZEW 6 mm
ZEW 35/2 8 mm
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.30
Busbars /
mounting rails
F.31
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Mounting rail systems
Mounting rail supports / Mounting feet
Thread Qty Order no.
TSTW 5/M5 M5 10 0178100000
TSTW 5/M5 verzinkt M5 10 1779100000
TSTW 6/M6 M6 10 0164000000
TSTW D 4.3 Hole ø 4,3 mm 10 1610110000
Mounting rail supports of type TSTW are used for
angled fixing of mounting rails at an angle of 35°.
TST 2/M5 M5 10 1286600000
TST 2/M6 M6 10 0101700000
The TST mounting rail support is used for assembly
of mounting rails in a frame or over a cut-out
Fixing screws
FKSC M5x8 Ø9500295900000
FKSC M6x8 Ø9500642600000
FKSC M6x12 Ø9500353500000
Weidmüller supplies fixing screws with hexagonal sockets and
a very low head for the mounting rail supports so that the terminals
can also be fitted over the screw.
Mounting rail supports
Clip-on foot, steel for TS 35 Thread Qty Order no.
FM 4 M4 40 0687900000
FM 5 M5 40 0636800000
FM 6 M6 40 0636900000
FM 4.2 Hole ø 4,2 mm 40 1724580000
Assembly foot, PA orange for TS 35
MOFU 35/LO/1 With holes 20 0646260000
MOFU 35 20 0495660000
Sliding nut for TS 34 Colour
MB M3/M5 M3 and M5 Cream 20 0503500000
MB M5/M3 M5 and M3 Black 20 0553400000
MB M6/M4 M6 and M4 Grey 20 0334900000
The sliding nut for the RS 32 mounting rail has two threaded
holes for screws M3 + M5 / M6 + M4 / M5 + M3.
It is used to fasten components which cannot be slotted di-
rectly onto the TS 32, in particular the smaller TS 15 top hat
rail.
This enables, for example, mini-terminals to be snapped onto
the TS 15 first, and this rail is then fastened together with the
terminals to the TS 32 using the sliding nut.
Mounting feet
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.31
Busbars /
mounting rails
F.32
F
Mounting rail systems
RailMate mounting rail system
for the TS 35 x 7.5 and TS 35 x 15 mounting rails
To save costs, it is possible to dispense with an expensive die
cast aluminium enclosure within a switch cabinet. The IP-20 so-
lution RailMate can be used instead.
The mounting rail assembly system can be used to mount the
inserts of the heavy-duty plug-in connectors and also the
“ConCept” modular plug-in connector system on the mounting
rail. This is all done without tools, simply by clipping the parts on.
A large surface at the base of the insert receptacle and on the
frame allow for clear identification of equipment.
In the switch cabinet, RailMate lets the user accommodate the
maximum number of electrical connections in a minimum area.
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.32
Busbars /
mounting rails
F.33
F
Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.
Delivery times see page X.2
Base plate
with slider
2 insert receptacle bottoms
Rider
(adjusts to sizes 3, 4, 6 and 8)
Insert receptacle frame
for sizes 3, 4, 6 and 8
Mounting rail systems
Technical data
Material PC
Properties Contains no phosphorous and halogen
Colour Pebble grey (RAL 7032)
Temperature range –40°C ... +125°C
Flammability class V-0 acc. to UL 94
Type Qty Order no.
Coding set
HDC RailMate COS 50 poles and plugs 1 1798260000
6 different coding versions
Marking labels for laser printer (1 sheet = 264 labels)
LM MT 300 20/8 Silver 10 sheets 1686380001
LM MT 300 20/8 White 10 sheets 1686381044
LM MT 300 20/8 Yellow 10 sheets 1686381687
Marking labels for thermotransfer printer (1 roll = 10,000 labels)
THM MT30X 32/9 Silver 1 roll 1751770001
LM MT 300 20/8 White 1 roll 1751771044
LM MT 300 20/8 Yellow 1 roll 1751771687
Accessories
Dimensional drawing
Order data individual components
RailMate mounting rail assembly system
Order data for individual components
Type For inserts of size Qty Order no.
Insert receptacle frame
HDC RailMate HB6 Top 3 10 1797540000
HDC RailMate HB10 Top 4 10 1797550000
HDC RailMate HB16 Top 6 10 1797560000
HDC RailMate HB24 Top 8 10 1797570000
Base plate, rider and 2 insert receptacle bottoms
HDC RailMate Basis 3, 4, 6, 8 1 1797580000
Order data sets
Type For inserts of size Qty Order no.
HDC RailMate HB6 Set 3 1 1797500000
HDC RailMate HB10 Set 4 1 1797510000
HDC RailMate HB16 Set 6 1 1797520000
HDC RailMate HB24 Set 8 1 1797530000
Each set consists of: 1 base plate
1 slider
2 insert receptacle bottoms
1 insert receptacle frame
Top
Basis
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.33
Busbars /
mounting rails
F.34
F
SSB_F001-F034_GB 25.10.2003 10:10 Uhr Seite F.34
