399
San Ace 92AD
■General Specications
・Material
……………………… Frame: Plastics (Flammability: UL94V-0),
Impeller: Plastics (Flammability: UL94V-0)
・Expected Life ……………… Refer to specications (L10:Survival rate: 90% at 60℃,
rated voltage,and continuously run in a free air state)
・Motor Construction ……… Brushless DC motor
・Motor Protection System Burnout protection at locked rotor condition
・Dielectric Strength ……… 50/60 Hz, 1,500 VAC, 1 minute (between input terminal
and frame, and between sensor output and frame)
・Insulation Resistance …… 10MΩ or more at 500VDC megger (between lead
conductor and frame)
・
Sound Pressure Level (SPL)
…Expressed as the value at 1m from air inlet side
・S
torage Temperature
……… −
30
℃
to
＋
75
℃
(Non-condensing
）
* Do not weld directly onto AC input terminals.
ACDC Fan
92×92×38mm
〔Mass：250g〕
92
mm sq.
■Specications
The model no. below has ribs and no sensors. For models without ribs, append "1" to the model no.
Model No. Rated Voltage
Operating Voltage Range
Frequency
(Note)
Rated Current
Rated Input Rated Speed
Max. Airow
Max. Static Pressure
SPL
Operating Temperature
Expected Life
［V］［V］［Hz］［A］［W］［min-1］［
m³/min
］［CFM］［Pa］［inchH²O］［dB( A ) ］［℃］ ［h］
9AD0901H12 100 to 240 90 to 264 50/60 0.08 4.5 3,850 1.50 53.0 90 0.36 40 −20 to ＋75
60,000/60
℃
9AD0901M12 0.06 3.0 3,100 1.18 41.7 56 0.22 33
Note: 50/60 Hz compatible.
The model no. below has ribs and low-speed sensors. For models without ribs, append "1" to the model no.
Model No. Rated Voltage
Operating Voltage Range
Frequency
(Note)
Rated Current
Rated Input Rated Speed
Max. Airow
Max. Static Pressure
SPL
Operating Temperature
Expected Life
［V］［V］［Hz］［A］［W］［min-1］［
m³/min
］［CFM］［Pa］［inchH²O］［dB( A ) ］［℃］ ［h］
9AD0901H1H 100 to 240 90 to 264 50/60 0.08 4.5 3,850 1.50 53.0 90 0.36 40 −20 to ＋75
60,000/60
℃
9AD0901M1H 0.06 3.0 3,100 1.18 41.7 56 0.22 33
Note: 50/60 Hz compatible.
Overheating protection function
Protection Functions:
If the fan blades are restricted, an overcurrent occurs and leads to a rise in the fan coil temperature. This can result in reduced performance,
damage, or a re. To prevent this from occurring, SANYO DENKI's fans incorporate an overheating protection function.
Burnout protection function at locked rotor condition
●Current cutoff system (ACDC fan only)
If the fan blades are restricted, the coil current is cut off at regular cycles to prevent overheating of the coil. When the hindrance is
removed, the fan restarts automatically.
9AD
type
400
回転方向 風吹出方向
取付用穴
38±0.5
(4) (4)
82.5±0.3
92±0.5
4-φ4.3±0.3
82.5±0.3
92±0.5
回転方向 風吹出方向
リード線
AWG24
UL1007
4-φ4.3±0.3
取付用穴
コネクタ：Tyco Electronics 171822-2 （Pin.1 センサ出力：黄色 Pin.2 −：黒色）
コンタクト：Tyco Electronics 170262-1
※装置側のコネクタ・コンタクトは以下を推奨いたします。
 コネクタ：Tyco Electronics 172211-2
 コンタクト：Tyco Electronics 170376-1
100±10
82.5±0.3
92±0.5 38±0.5
(4) (4)
82.5±0.3
92±0.5
4-φ4.54-φ4.5
φ
105
90.5
90.5
φ
97
82.5±0.3 82.5±0.3
82.5±0.3
82.5±0.3
90.5
90.5
AC
ACDC Fan 92mm
without Sensor
■Dimensions（unit: mm）
(With ribs)
■Reference Dimensions of Mounting Holes and Vent Opening（unit: mm）
Inlet side Outlet side
with Low-speed sensor
Rotating Direction
Mounting Hole
Mounting Hole
Airow Direction
Rotating Direction Airow Direction
Lead Wire
AWG24
UL1007
Connector: Tyco Electronics 171822-2 (Pin1 Sensor output: Yellow Pin2 –: Black)
Contact: Tyco Electronics 170262-1
* Recommended connectors and contacts are listed below.
Connector: Tyco Electronics 172211-2
Contact: Tyco Electronics 170376-1
401
San Ace 92AD
4-φ9.5±0.5
96.5±1
82.5±0.3
96.5±1
82.5±0.3
4-φ4.3±0.3
10.5±0.5
4-2±0.5 質量： 25g
先端予備はんだ
50
±
5
10
±
2
L
20 417
10
15.5 8
10
8
4
予備はんだ
1000±20
10±1
質量：9g
120.5
99
＋1. 5
ー0.5
4.3±0.3 5＋1
0
φ
116.6
φ1.6
φ1.6
φ
39.8
φ
87
質量：22g
4.3±0.3
φ1.6
φ1.6
φ
116.6
φ
87
120.5＋1.5
−0.5
99
5＋1
 0
φ16.2
質量：29g
4-2±0.5
92±1
82.5±0.3
92±1
82.5±0.3 4-φ4.3±0.3
7±0.5
質量：12g
92×92×38mm
〔Mass：250g〕
ACDC Fan
■Options（unit: mm）
Finger Guards
Model ：109-099C Surface treatment ：Nickel-chrome plating （silver）
Color
Outlet side
Model ：109-099E
：109-099H
Surface treatment ：Nickel-chrome plating （silver）
：Cation electropainting （black）
Color
Inlet side, Outlet side
Resin Filter Kits
Model: 109-1001F13 (13PPI), 109-1001F20 (20PPI), 109-1001F30 (30PPI), 109-1001F40 (40PPI)
Plug Cord
(Products compliant with Electrical Appliance and Material Safety Law, UL /CSA [c-UL] CERTIFIED)
UL FILE No. E43202
Model
：
489-1635-L10/489-1635-L21
Wiring Harness for Sensor
Model: 489-1636
92
mm sq.
Pre-soldered
Pre-soldered
Mass
Mass
Mass
Model Power cord length (L) [mm] Mass [g]
489-1635-L10 1,000 38
489-1635-L21 2,100 74
Mass
Resin Finger Guards
Model：109-1001G
Mass
402
100〜240V 50/60Hz
→ 静圧
→ 風量
（inch H2O）
（CFM）
（m3/min）
（Pa）
20
0 0.4 0.8 1.2 1.6
40
60
80
100
10020304050
0.1
0
0.2
0.3
0.4
100〜240V 50/60Hz
→ 静圧
→ 風量
（inch H2O）
（CFM）
（m3/min）
（Pa）
20
0 0.4 0.8 1.2 1.6
10
30
40
50
60
100 20304050
0.05
0
0.10
0.15
0.20
9AD0901H12
9AD0901H1H
9AD0901M12
9AD0901M1H
AC
ACDC Fan 92mm
■ Airow - Static Pressure Characteristics
→
Static Pressure
→
Static Pressure
→ Airow → Airow
■Wiring Diagram
■Specications for Low-speed Sensors
100 to 240 V 50/60 Hz 100 to 240 V 50/60 Hz
VCE＝＋27.6 V DC MAX.
Ic＝10 mA MAX.［VCE (SAT) ＝1.0 V MAX.］
Sensor scheme
HH
L
Fan power
Fan speed Trip point
Sensor output
Startup delay Detection delay
Example 2: when the rotor is locked when the fan motor is
turned on and released after the start-up delay time.
HH
L
Fan power
Fan speed Trip point
Sensor output
Startup delay Detection delay
Example 1: when steady running
VCE (SAT) = 1.0 V MAX.
Typical standard model: 9AD0901H1H
Output circuit: Open collector
Inside of DC fan
Pull-up resistor
Pull-up voltage ＋27.6 V DC MAX.
Photocoupler
○−
Ic＝10 mA MAX.
Sensor
Sensor output
(VCE)
9AD0901M1H
Startup delay: 36±3 sec.
Detection delay: 3 sec. MAX.
Trip point: 850 min-1
9AD0901H1H
Startup delay: 18±3 sec.
Detection delay: 3 sec. MAX.
Trip point: 1,700 min-1
FAN
FAN
Photocoupler Yellow
Black
10 mA MAX.
+27.6 V MAX.
Senser output
GND (0 V)
Standard with Sensor
AC Power supply
AC Power supply
Pull-up resistor