SMD Low Ohmic - Current Sense Resistors
Type RL73 Series
2
1773269 CIS BI 06/2011 Dimensions are in millimeters Dimensions are shown for For email, phone or live chat, go to: te.com/help
and inches unless otherwise reference purposes only.
specified. Values in brackets Specifications subject
are standard equivalents. to change.
Characteristics - Environmental
Item Requirement Test Method
Temperature Coefficient As spec +25/-55/+25/+125/+25°C
of Resistance (TCR):
Short Time Overload: ±0.5% RCWV*2.5 or Max. overload voltage for 5 seconds
ΔR ±1% for high power rating
Insulation Resistance: >1000MΩ Apply 100VDC for 1 minute
±1% 70 ±2°C, Max. working voltage for 1000hrs with
Endurance: 1.5hrs “ON” and 0.5hrs “OFF”
Damp Heat with Load: ±0.5% 40 ±2°C, 90 - 95% R.H. max. working voltage
for 1000hrs with 1.5hrs “ON” and 0.5hrs “OFF”
Dry Heat: ±0.5% at +155°C for 1000hrs
Bending Strength: As spec Bending amplitude 3mm for 10 seconds
Solderability: 95% min. coverage 245 ±5°C for 3 seconds
Resistance to Soldering Heat: ±0.5% 260 ±5°C for 10 seconds
Dielectric Withstand Voltage: By type Apply Max. overload voltage for 1 minute
Thermal Shock: ±0.5% -55°C to +150°C, 100 cycles
Low Temperature Operation: ±0.5% 1 hour, -65°C, followed by 45 minutes of RCWV
Reference Standards: MIL-STD-202, JIS-C 5201-1
Storage Temperature: 25±3°C; Humidity < 80%RH
Dimensions
Part Number L W C D t
RL73 1H (0201) 0.58 ±0.05 0.29 ±0.05 0.15 ±0.05 0.12 ±0.05 0.23 ±0.05
RL73 1E (0402) 1.00 ±0.05 0.50 ±0.05 0.20 ±0.10 0.25 ±0.10 0.32 ±0.10
RL73 1J (0603) 1.60 ±0.10 0.80 ±0.10 0.30 ±0.20 0.30 ±0.20 0.45 ±0.10
RL73 2A (0805) 2.00 ±0.15 1.25 ±0.15 0.40 ±0.25 0.30 ±0.20 0.55 ±0.10
RL73 2B (1206) 3.10 ±0.10 1.55 ±0.15 0.40 ±0.25 0.50 ±0.30 0.55 ±0.10
RL73 2E (1210) 3.10 ±0.10 2.50 ±0.15 0.50 ±0.25 0.50 ±0.30 0.55 ±0.10
RL73 2H (2010) 5.00 ±0.20 2.50 ±0.15 0.50 ±0.25 0.60 ±0.30 0.60 ±0.15
RL73 3A (2512) 6.35 ±0.20 3.10 ±0.15 0.55 ±0.25 0.60 ±0.30 0.60 ±0.10
L
D
W
t
C
1. Alumina Substrate
2. Bottom Electrode (Ag)
3. Top Electrode (Ag-Pd)
4. Edge Electrode (NiCr)
5. Barrier Layer (Ni)
6. External Electrode (Sn)
7. Resistor Layer (NiCr)
8. Overcoat (Epoxy)
9. Marking