929000778113 - NXP SEMICONDUCTORS

ILLUMINATION

No. E352519

LUXEON M is an illumination grade multi-die LED designed to enable

outdoor and industrial applications targeting either high eciency or low

cost. With Freedom from Binning and leading performance, LUXEON M

falls within a single 3- or 5-step MacAdam ellipse centered in ANSI to

ensure color consistency from LED to LED, delivering high ecacy and

high ux density from a uniform source with tight correlated color

temperature control. The superior quality of light, volume of lumens,

and real world ecacy enable leading performance and ecient solution

development in a wide variety of lighting segments.

LUXEON M

Brightest, most uniform and highest

ecacy multi-die emitter

FEATURES AND BENEFITS PRIMARY APPLICATIONS

Uniform image enables tight beam control in MR16 and spotlight applications Architectural

High ux density from a 3mm2 area enables reduced emitter count and

compact xture designs High Bay & Low Bay

11.2V, 5.6V and 2.8V package options puts high performance within reach

with high eciency and low cost drivers Lamps

Leading thermal resistance allows exible system design to optimize for

lm/$ and lm/W Outdoor

Exceeds ENERGY STAR® lumen maintenance requirements Specialty Lighting

Spotlights

Table of Contents

General Product Information ......................................................................2

Product Test Conditions ..............................................................................2

Part Number Nomenclature ..........................................................................2

Lumen Maintenance .................................................................................2

Environmental Compliance ...........................................................................2

Performance Characteristics ......................................................................3

Product Selection Guide..............................................................................3

Optical Characteristics ...............................................................................4

Electrical and Thermal Characteristics..................................................................4

Absolute Maximum Ratings .......................................................................5

Operating Conditions ................................................................................5

Characteristic Curves .............................................................................6

Spectral Power Distribution Characteristics .............................................................6

Light Output Characteristics ..........................................................................8

Forward Current Characteristics......................................................................10

Radiation Pattern Characteristics .....................................................................12

Product Bin and Labeling Denitions ..............................................................13

Decoding Product Bin Labeling.......................................................................13

Luminous Flux Bins .................................................................................14

Radiometric Power Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Color Bin Denition .................................................................................15

Dominant Wavelength Bins ..........................................................................15

Forward Voltage Bins ...............................................................................16

Mechanical Dimensions..........................................................................16

Reow Soldering Guidelines ......................................................................17

JEDEC Moisture Sensitivity ...........................................................................17

Solder Pad Design ..................................................................................18

Packaging Information...........................................................................19

Pocket Tape Dimensions ............................................................................19

Reel Dimensions ...................................................................................20

General Product Information

Product Test Conditions

LUXEON M LEDs are tested and binned with a DC drive current of 700mA for LUXEON M 12V, 1400mA for LUXEON M 6V and

2800mA for LUXEON M 3V at a junction temperature, Tj, of 85ºC.

Part Number Nomenclature

Part numbers for LUXEON M follow the convention below:

L X R A – B C D D – E E E E

Where:

A – designates minimum CRI (7=70, 8=80, 9=90, 0=Royal Blue)

B – designates voltage (S=12V, R=6V, Q=3V)

C – designates color (W=White, R=Royal Blue)

D D – designates CCT (27=2700K, 30=3000K, 35=3500K, 40=4000K, 50=5000K, 57=5700K, 65=6500K, 00=Royal Blue)

E E E E – designates minimum luminous ux (optional)

Therefore, the following part number is used for a white LUXEON M 12V 3000K 80CRI:

L X R 8 – S W 3 0 – x x x x

Lumen Maintenance

Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the long-

term performance of this product.

Environmental Compliance

Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON M is

compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the

RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted

materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated

diphenyl ethers (PBDE).

Performance Characteristics

Product Selection Guide

Table 1a. Product performance for LUXEON M White at test current, Tj=85°C.

VOLTAGE NOMINAL CCT [2] MINIMUM

CRI

LUMINOUS FLUX [1] (lm)TEST CURRENT

(mA) PART NUMBER

MINIMUM TYPICAL

12V

3000K 70 900 1000 700 LXR7-SW30

4000K 70 970 1076 700 LXR7-SW40

5000K 70 1040 1100 700 LXR7-SW50

5700K 70 1040 1110 700 LXR7-SW57

6500K 70 1040 1130 700 LXR7-SW65

2700K 80 730 800 700 LXR8-SW27

3000K 80 780 850 700 LXR8-SW30

3500K 80 780 870 700 LXR8-SW35

4000K 80 840 905 700 LXR8-SW40

5000K 80 840 920 700 LXR8-SW50

2700K 90 600 660 700 LXR9-SW27

3000K 90 640 736 700 LXR9-SW30

5700K 90 800 880 700 LXR9-SW57

3000K 70 900 1000 1400 LXR7-RW30

4000K 70 970 1076 1400 LXR7-RW40

5000K 70 1040 1100 1400 LXR7-RW50

5700K 70 1040 1110 1400 LXR7-RW57

6500K 70 1040 1130 1400 LXR7-RW65

2700K 80 730 800 1400 LXR8-RW27

3000K 80 780 850 1400 LXR8-RW30

3500K 80 780 870 1400 LXR8-RW35

4000K 80 840 920 1400 LXR8-RW40

5000K 80 840 920 1400 LXR8-RW50

2700K 90 600 660 1400 LXR9-RW27

3000K 90 640 736 1400 LXR9-RW30

5700K 90 800 880 1400 LXR9-RW57

3000K 70 900 1000 2800 LXR7-QW30

4000K 70 970 1076 2800 LXR7-QW40

5000K 70 1040 1100 2800 LXR7-QW50

5700K 70 1040 1110 2800 LXR7-QW57

6500K 70 1040 1130 2800 LXR7-QW65

2700K 80 730 800 2800 LXR8-QW27

3000K 80 780 850 2800 LXR8-QW30

3500K 80 780 870 2800 LXR8-QW35

4000K 80 840 920 2800 LXR8-QW40

5000K 80 840 920 2800 LXR8-QW50

2700K 90 600 660 2800 LXR9-QW27

3000K 90 640 736 2800 LXR9-QW30

5700K 90 800 880 2800 LXR9-QW57

Notes for Table 1a:

1. Lumileds maintains a tolerance of ±2 on CRI and ±6.5% on luminous ux measurements.

2. Typical CRI is approximately 2 points higher than the minimum CRI specied, but this is not guaranteed.

Table 1b. Product performance for LUXEON M Royal Blue at test current, Tj=85°C.

VOLTAGE DOMINANT WAVELENGTH (nm)RADIOMETRIC POWER (mW) TEST CURRENT

(mA) PART NUMBER

MINIMUM MAXIMUM MINIMUM TYPICAL

12V 445 460 4200 4500 700 LXR0-SR00

6V 445 460 4200 4500 1400 LXR0-RR00

3V 445 460 4200 4500 2800 LXR0-QR00

Notes for Table 1b:

1. Lumileds maintains a tolerance of ±6.5% on radiometric power measurements.

Optical Characteristics

Table 2. Optical characteristics for LUXEON M at test current, Tj=85°C.

PART NUMBER TYPICAL TOTAL INCLUDED ANGLE [1] TYPICAL VIEWING ANGLE [2]

LXRx-xxxx 140° 120°

Notes for Table 2:

1. Total angle at which 90% of total luminous ux is captured.

2. Viewing angle is the o axis angle from the LED centerline where the luminous intensity is ½ of the peak value.

Electrical and Thermal Characteristics

Table 3. Electrical and thermal characteristics for LUXEON M at test current, Tj=85ºC.

PART NUMBER

FORWARD VOLTAGE (V) [1] TYPICAL TEMPERATURE

COEFFICIENT OF FORWARD

VOLTAGE (mV/°C) [2]

TYPICAL THERMAL

RESISTANCE — JUNCTION

TO SOLDER PAD (°C/W)

MINIMUM TYPICAL MAXIMUM

LXRx-Sxxx 10.50 11.20 11.70 -5.50 1.25

LXRx-Rxxx 5.25 5.60 6.00 -2.75 1.25

LXRx-Qxxx 2.63 2.80 3.00 -1.38 1.25

Notes for Table 3:

1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.

2. Measured between 25°C and 135°C.

Absolute Maximum Ratings

Table 4. Absolute maximum ratings for LUXEON M.

PARAMETER MAXIMUM PERFORMANCE

DC Forward Current at Tj=110°C [1][2]

1200mA for LXRx-SWxx

2400mA for LXRx-RWxx

4800mA for LXRx-QWxx

DC Forward Current at Tj=135°C [1][2]

1050mA for LXRx-Sxxx

2100mA for LXRx-Rxxx

4200mA for LXRx-Qxxx

Peak Pulsed Forward Current [3]

1375mA for LXRx-SWxx

2750mA for LXRx-RWxx

5500mA for LXRx-QWxx

1200mA for LXR0-SR00

2400mA for LXR0-RR00

4800mA for LXR0-QR00

LED Junction Temperature (DC & Pulse) -40°C to 135°C

ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012) Class 3B

Operating Case Temperature [1] 120°C

Storage Temperature -40°C to120°C

Soldering Temperature JEDEC 020c 260°C

Allowable Reow Cycles 3

Reverse Voltage (Vreverse)LUXEON LEDs are not designed to be driven in reverse bias

Notes for 4:

1. See Figure 1 for more details on the maximum permissible operating conditions for LUXEON M White.

2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple”, are acceptable if the following conditions are met:

– The frequency of the ripple current is 100Hz or higher

– The average current for each cycle does not exceed the maximum allowable DC forward current at this junction temperature

– The maximum amplitude of the ripple does not exceed 15% of the maximum allowable DC forward current at this junction temperature

3. At 10% duty cycle with pulse width of 10ms.

Operating Conditions

Notes for Figure 1:

1. The green shaded area in this graph reects the maximum permissible operating conditions for LUXEON M White.

Figure 1: Maximum permissible operating conditions for LUXEON M White.

135110

If1

If2

Junction

Temperature [°C]

Drive Current

-40

If1 [mA] If2 [mA]

LUXEON M White 3V 4200 4800

LUXEON M White 6V 2100 2400

LUXEON M White 12V 1050 1200

Characteristic Curves

Spectral Power Distribution Characteristics

Figure 2a: Typical normalized power vs. wavelength for LXR7-xWxx at test current, Tj=85ºC.

Figure 2b: Typical normalized power vs. wavelength for LXR8-xWxx at test current, Tj=85ºC.

LXR7-xW30

LXR7-xW40

LXR7-xW50

LXR7-xW57

LXR7-xW65

Figure 2c: Typical normalized power vs. wavelength for LXR9-xWxx at test current, Tj=85ºC.

Figure 2d: Typical normalized power vs. wavelength for LXR0-xR00 at test current, Tj=85ºC.

Light Output Characteristics

Figure 3: Typical normalized light output vs. junction temperature for LXRx-xxxx at test current, Tj=85ºC.

Figure 4a: Typical normalized light output vs. forward current for LXRx-Sxxx at test current, Tj=85ºC.

Figure 4b: Typical normalized light output vs. forward current for LXRx-Rxxx at test current, Tj=85ºC.

Figure 4c: Typical normalized light output vs. forward current for LXRx-Qxxx at test current, Tj=85ºC.

Forward Current Characteristics

Figure 5a: Typical forward current vs. forward voltage for LXRx-Sxxx at Tj=85ºC.

Figure 5b: Typical forward current vs. forward voltage for LXRx-Rxxx at Tj=85ºC.

Figure 5c: Typical forward current vs. forward voltage for LXRx-Qxxx at Tj=85ºC.

Radiation Pattern Characteristics

Figure 6: Typical radiation pattern for LXRx-xxxx at test current, Tj=85ºC.

Figure 7: Typical polar radiation pattern for LXRx-xxxx at test current, Tj=85ºC.

Product Bin and Labeling Denitions

Decoding Product Bin Labeling

In the manufacturing of semiconductor products, there are variations in performance around the average values given in the

technical datasheet. For this reason, Lumileds bins LED components for luminous ux or radiometric power, color point, peak or

dominant wavelength and forward voltage.

Reels with LUXEON M White LEDs are labeled using a 4-digit alphanumeric CAT code following the format below:

A B C D

A – designates luminous ux bin (example: M=630 to 680 lumens, T=970 to 1040 lumens)

B – designates color bin (example: 1=6500K, 2=5700K, 3=5000K, 5=4000K, 6=3500K, 7=3000K, 8=2700K)

C – designates color space (example: 5=5-step MacAdam Ellipse, 3=3-step MacAdam Ellipse)

D – designates forward voltage bin (example: F, G, H)

Therefore, a white LUXEON M with a lumen range of 630 to 680, color of 3000K, 5-step MacAdam ellipse and a forward voltage

range of 2.63 to 2.75V for 3 volt parts has the following CAT code:

M 7 5 F

Reels of LUXEON M Royal Blue LEDs are labeled using a 3-digit alphanumeric CAT code following the format below:

A B C

A – designates radiometric power bin (example: B=4200 to 4400mW, D=4600 to 4800mW)

B – designates dominant wavelength bin (example: 5=450 to 455nm, 6=455 to 460nm)

C – designates forward voltage bin (example: F, G, H)

Therefore, a Royal Blue LUXEON M with a radiometric power range of 4200 to 4400mW, peak of dominant wavelength 450 to

455nm a forward voltage range of 11.50 to 11.70V for 12 volt parts has the following CAT code:

B 5 H

Luminous Flux Bins

Table 5 lists the standard photometric luminous ux bins for LUXEON M emitters. Although several bins are outlined, product

availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs.

Table 5. Luminous ux bin denitions for LUXEON M White.

BIN LUMINOUS FLUX (lm)

MINIMUM MAXIMUM

J 510 550

K550 590

L 590 630

M 630 680

N 680 730

P 730 780

Q780 840

R 840 900

S 900 970

T 970 1040

U 1040 1120

V 1120 1200

W 1200 1290

Notes for Table 5:

1. Lumileds maintains a tolerance of ±6.5% on luminous ux measurements.

Radiometric Power Bins

Table 6. Radiometric power bin denitions for LUXEON M Royal Blue.

BIN RADIOMETRIC POWER (mW)

MINIMUM MAXIMUM

A 4000 4200

B 4200 4400

C 4400 4600

D 4600 4800

E 4800 5000

Notes for Table 6:

1. Lumileds maintains a tolerance of ±6.5% on radiometric power measurements.

Color Bin Denition

Table 7. 3- and 5-step MacAdam ellipse color bin denitions for LUXEON M.

NOMINAL CCT COLOR SPACE CENTER POINT

(cx, cy)

MAJOR AXIS,

MINOR AXIS,

ELLIPSE ROTATION

ANGLE, Θ

2700K Single 3-step MacAdam ellipse 0.4578, 0.4101 0.00810 0.00420 53.70

3000K Single 3-step MacAdam ellipse 0.4338, 0.4030 0.00834 0.00408 53.22

3500K Single 3-step MacAdam ellipse 0.4073, 0.3917 0.00927 0.00414 54.00

4000K Single 3-step MacAdam ellipse 0.3818, 0.3797 0.00939 0.00402 53.72

5000K Single 3-step MacAdam ellipse 0.3447, 0.3553 0.00822 0.00354 59.62

3000K Single 5-step MacAdam ellipse 0.4338, 0.4030 0.01390 0.00680 53.22

4000K Single 5-step MacAdam ellipse 0.3818, 0.3797 0.01565 0.00670 53.72

5000K Single 5-step MacAdam ellipse 0.3447, 0.3553 0.01370 0.00590 59.62

5700K Single 5-step MacAdam ellipse 0.3287, 0.3417 0.01243 0.00533 59.09

6500K Single 5-step MacAdam ellipse 0.3123, 0.3282 0.01115 0.00475 58.57

Notes for Table 7:

1. Lumileds maintains a tolerance of ±0.005 on x and y coordinates in the CIE 1931 color space.

Dominant Wavelength Bins

Table 8. Dominant wavelength bins for LUXEON M Royal Blue.

BIN DOMINANT WAVELENGTH (nm) [1]

MINIMUM MAXIMUM

4 445 450

5 450 455

6 455 460

Notes for Table 8:

1. Lumileds maintains a tolerance of ±0.5nm on dominant wavelength measurements.

Figure 8: 3- and 5-step MacAdam ellipse illustration for Table 7.

Forward Voltage Bins

Table 9. Forward voltage bin denitions for LUXEON M.

PART NUMBER BIN FORWARD VOLTAGE (V) [1]

MINIMUM MAXIMUM

LXRx-SWxx

and LXR0-SR00

F 10.50 11.00

G 11.00 11.50

H 11.50 11.70

LXRx-RWxx

and LXR0-RR00

F 5.25 5.50

G 5.50 5.75

H 5.75 6.00

LXRx-QWxx

and LXR0-QR00

F 2.63 2.75

G 2.75 2.88

H 2.88 3.00

Notes for Table 9:

1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.

Mechanical Dimensions

Notes for Figure 9:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Figure 9: Mechanical dimensions for LUXEON M.

7.00±0.12

6.40 0.06

3.14±0.10

3.50±0.15

3.50±0.15 3.75±0.12

0.56±0.08

R0.20±0.04

Reow Soldering Guidelines

Table 10. Reow prole characteristics for LUXEON M.

PROFILE FEATURE LEAD-FREE ASSEMBLY

Preheat Minimum Temperature (Tsmin)150°C

Preheat Maximum Temperature (Tsmax)200°C

Preheat Time (tsmin to tsmax)60 to 120 seconds

Ramp-Up Rate (Tsmax to Tp) 3°C / second maximum

Liquidus Temperature (TL)217°C

Time Maintained Above Temperature TL (tL)60 to 150 seconds

Peak / Classication Temperature (Tp)260°C

Time Within 5°C of Actual Temperature (tp)20 to 40 seconds

Ramp-Down Rate 6°C / second maximum

Time 25°C to Peak Temperature 8 minutes maximum

Notes for Table 10:

1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body.

JEDEC Moisture Sensitivity

Table 11. Moisture sensitivity levels for LUXEON M.

LEVEL FLOOR LIFE SOAK REQUIREMENTS STANDARD

TIME CONDITIONS TIME CONDITIONS

1 Unlimited ≤30°C / 85% RH 168 Hours +5 / -0 85°C / 85% RH

Time 25ºC to Peak

JEDEC J-STD-020D

Critical Zone

TL to Tp

Ramp-up

Ramp-down

Temperature

Time

Preheat Area

Tsmax

Tsmin

Figure 10: Visualization of the acceptable reow temperature prole as specied in Table 10.

Solder Pad Design

Notes for Figure 11:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Figure 11: Recommended PCB solder pad layout for LUXEON M.

Packaging Information

Pocket Tape Dimensions

Notes for Figure 12:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Figure 12: Pocket Tape dimensions for LUXEON M.

DIRECTION OF FEED

4.00mm INDEX HOLE PITCH

12.00mm POCKET PITCH

1.50

1.50 2.00

1.75

7.50

4.59

1.59

4.99

B B

7.35 SQ.

4.11

0.38

4.49 4.99

5.35

8°

SECTION B-B

SCALE 2 : 1

16.00

4°

-LOADED POCKETS-

500

-LEADER-

50 EMPTY POCKETS

-TAPE END-

30 EMPTY POCKETS

DIRECTION OF FEED

DETAIL E

SCALE 4 : 1

-DEVICE ORIENTATION-

NON-FIDUCIAL CORNER

LOCATEDAS SHOWN

DETAIL F

SCALE 4 : 1

Reel Dimensions

Notes for Figure 13:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Figure 13: Reel dimensions for LUXEON M.

13.00mm ARBOR

HOLE DIAMETER

330.00 REEL DIAMETER

DIRECTION OF FEED

CARRIER TAPE

COVER TAPE

TAPE REEL

20.8mm OUTSIDE WIDTH

16.4mm INSIDE WIDTH

DS103 LUXEON M

Product Datasheet 20150820

LUXEON is a registered trademark of the Lumileds Holding B.V.

in the United States and other countries.

lumileds.com

Neither Lumileds Holding B.V. nor its aliates shall be liable for any kind of loss of data or

any other damages, direct, indirect or consequential, resulting from the use of the provided

information and data. Although Lumileds Holding B.V. and/or its aliates have attempted to

provide the most accurate information and data, the materials and services information and data

are provided “as is,” and neither Lumileds Holding B.V. nor its aliates warrants or guarantees

the contents and correctness of the provided information and data. Lumileds Holding B.V. and its

aliates reserve the right to make changes without notice. You as user agree to this disclaimer

and user agreement with the download or use of the provided materials, information and data.

About Lumileds

Lumileds is the light engine leader, delivering innovation, quality and reliability.

For 100 years, Lumileds commitment to innovation has helped customers pioneer breakthrough products in the automotive,

consumer and illumination markets.

Lumileds is shaping the future of light with our LEDs and automotive lamps, and helping our customers illuminate how people

see the world around them.

To learn more about our portfolio of light engines, visit lumileds.com.