Technical Data Sheet Right Angle Lens Chip LEDs with Bi-Color(Multi-Color) 12-22SDRSYGC/S530-A3/E3/TR8 Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mulit-color type. Pb-free. The product itself will remain within RoHS compliant version. Descriptions The 12-22 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Chip Emitted Color Type Material SDR AlGaInP Deep- Red SYG AlGaInP Brilliant Yellow Green Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Resin Color Water Clear Rev 1 Page: 1 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Package Outline Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 2 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF Peak Forward Current (Duty 1/10 @1KHz) SDR:25 SYG:25 IFP SDR:60 SYG:60 SDR:60 mA mA Power Dissipation Pd Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40~ +90 Soldering Temperature Tsol SYG:60 mW Reflow Soldering : 260 for 10 sec. Everlight Electronics Co., Ltd. Device No: DSE-0006303 Hand Soldering : 350 for 3 sec. http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 3 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Electro-Optical Characteristics (Ta=25) Parameter Symbol Iv Luminous Intensity Viewing Angle Peak Wavelength Min. Typ. Max. SDR 26 32 ----- SYG 31 42 ----- ----- 120 ----- deg ----- nm 21/2 p SDR ----- SYG d Dominant Wavelength ----- SDR Forward Voltage Reverse Current 575 650 ----- SDR 573 ----- SYG IR ----- Device No: DSE-0006303 nm 20 1.7 2.0 2.4 SYG 1.7 2.0 2.4 ----- ----- 10 V A VR=5V 10 SYG Everlight Electronics Co., Ltd. ----- SDR SDR IF=20mA 20 ----- VF Condition mcd nm SYG Spectrum Radiation Bandwidth 639 Unit http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 4 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Typical Electro-Optical Characteristics Curves SDR Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 5 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Typical Electro-Optical Characteristics Curves SYG Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 6 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Label explanation CAT: Luminous Intensity Rank Pb EVERLIGHT HUE: Dom. Wavelength Rank CPN : P N : XXXXXXXXXXXXX REF: Forward Voltage Rank XXXXXXXXXXXXX RoHS CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 7 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Desiccant Rev 1 Label Page: 8 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 2605 Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 Temp. : 100 1000 Hrs. 22 PCS. 0/1 Temp. : -40 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 9 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No: DSE-0006303 http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 10 of 11 Prepared by: Yang Junyu 12-22SDRSYGC/S530-A3/E3/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No: DSE-0006303 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date: 25-Dec.-2011 Rev 1 Page: 11 of 11 Prepared by: Yang Junyu