Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Technical Data Sheet
Right Angle Lens Chip LEDs with Bi-Color(Multi-Color)
12-22SDRSYGC/S530-A3/E3/TR8
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mulit-color type.
․Pb-free.
․The product itself will remain within RoHS compliant
version.
Descriptions
․The 12-22 SMD LED is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Emitted Color
Resin Color
Type
Material
SDR
AlGaInP
Deep- Red
Water Clear
SYG
AlGaInP
Brilliant Yellow Green
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 2 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 3 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
SDR:25
SYG:25
mA
Peak Forward Current
(Duty 1/10 @1KHz)
IFP
SDR:60
SYG:60
mA
Power Dissipation
Pd
SDR:60
SYG:60
mW
Electrostatic Discharge(HBM)
ESD
2000
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40~ +90
℃
Soldering Temperature
Tsol
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 4 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Luminous Intensity
Iv SDR
SYG
26
31
32
42
-----
-----
mcd
IF=20mA
Viewing Angle
2θ1/2
-----
120
-----
deg
Peak Wavelength
λp SDR
SYG
-----
639
575
-----
nm
Dominant Wavelength
λd SDR
SYG
-----
-----
650
573
-----
-----
nm
Spectrum Radiation
Bandwidth
△λ SDR
SYG
-----
20
20
-----
nm
Forward Voltage
VF SDR
SYG
1.7
1.7
2.0
2.0
2.4
2.4
V
Reverse Current
IR SDR
SYG
-----
-----
10
10
μA
VR=5V
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 5 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Typical Electro-Optical Characteristics Curves
SDR
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 6 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Typical Electro-Optical Characteristics Curves
SYG
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 7 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
RoHS
Pb
CPN :
P N : XXXXXXXXXXXXX
XXXXXXXXXXXXX
QTY : XXX
LOT NO : XXXXXXXXXX
Reference : XXXXXXXX
CAT : XXX
HUE : XXX
REF : XXX
EVERLIGHT
MADE IN TAIWAN
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 8 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label Desiccant Label
Aluminum moisture-proof bag
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 9 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
No.
Items
Test Condition
Test
Hours/Cycles
Sample
Size
Ac/Re
1
Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec.
6 Min.
22 PCS.
0/1
2
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
3
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
4
High Temperature
Storage
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
5
Low Temperature
Storage
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 10 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
12-22SDRSYGC/S530-A3/E3/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 11 of 11
Device No: DSE-0006303 Prepared date: 25-Dec.-2011 Prepared by: Yang Junyu
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of the
hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com
