1/4
REV. A
STRUCTURE Silicon Monolithic Integrated Circuit
PRODUCT NAME Overvoltage Protection Controller with Internal FET
MODEL NAME BD6041GUL
FEATURES ●Overvoltage Protection up to 28V
●Internal Low Ron (125m ) FET
●Over voltage Lockout (OVLO)
●Under voltage Lockout(U VLO)
●Internal 2msec Startup Delay
●Over Current Protect
●Thermal Shut Down
●Small package : VCSP50L1( 1. 6mm x 1.6mm, height=0.55mm)
● Absolute maximum ratings (Ta=25℃)
Contents Symbol Rating Unit Conditions
Input supply voltage 1 Vmax1 -0.3～30 V IN
Input supply voltage 2 Vmax2 -0.3～7 V other
Power dissipation Pd 725 mW
Operating temperature range Topr -35～+85 ℃
Storage temperature range Tstr -55～+150 ℃
※1 When using more than at Ta=25℃, it is reduced 5.8 mW per 1℃.
ROHM specification boar d 50mm× 58mm mounting.
● Operating range (Ta=-35～+85℃)
Parameter Symbol Range Unit Usage
Input voltage range Vin 2.2～28 V
※ This product is not especially designed to be protected from radioactivity.
2/4
REV. A
● Electrical Characteristics
(Unless otherwise noted, Ta = 25C, IN=5V)
Parameter Symbol Rating Unit Conditions
Min. Typ. Max.
● ELECTRICAL
Input Voltage Range VIN - - 28 V
Supply Quiescent Current ICC 45 90
A
Under Voltage Lockout UVLO 2.53 2.65 2.77 V IN=decreasing
Under Voltage Lockout Hysteresis UVLOh 50 100 150 mV IN=increasing
Over Voltage Lockout OVLO 5.7 5.85 6.0 V IN=increasing
Over Voltage Lockout Hysteresis OVLOh 50 100 150 mV IN=decreasing
Current limit ILM 1.2 - - A
Vin vs. Vout Res. RON - 125 150 m
OK Output Low Voltage OKVO - - 400 mV SINK=1mA
OK Leakage Current OKleak - - 1
A
EN input voltage (H) ENH 1.45 - - V
EN input voltage (L) ENL - - 0.5 V
EN input current ENC 12 25 50
A
EN=1.5V
● TIMINGS
Start Up Delay Ton - 2 4 msec
OK Going Up Delay Tok - 10 15 msec
Output T urn Off Ti me Tof f - 2 10
sec
Alert Delay Tovp - 1.5 10
sec
* This product is not especially designed to be protected from radioactivity.
3/4
REV. A
● Block Diagram ● PIN number/PIN name
● PIN DESCRIPTIONS
PIN NAME FUNCTION
A2, A3
B2, B3 IN1, 2,
3, 4 Input voltage Pin. A 1
F low ESR capacitor,
or larger must be connected between this pin and GND
A1, B1 OUT1, 2 Output Voltage Pin
C1 OK Active-low open drain output to signal if the adapter voltage is correct
C3 GND Ground Pin
C2 EN Enable input Drive EN high to turn off OUT (Hi-z output)
● Package Dimensions (VCSP50L1)
Pin
number Pin name
A2 IN1
A3 IN2
B2 IN3
B3 IN4
A1 OUT1
B1 OUT2
C3 GND
C1 OK
C2 EN
6041
LOT No.
4/4
REV. A
●Use-related Cautions
(1) Ab sol ute ma ximum ratings
If applied voltage (VDD, VIN), operating temperature range (Topr), or other absolute maximum ratings are exceeded, there is a risk of damage. Since
it is not possible to identify short, open, or other damage modes, if special modes in which absolute maximum ratings are exceeded are assumed,
consider applying fuses or other phy sical safety measures.
(2) Recommended operating range
This is the range within which it is possible to obtain roughly the expected characteristics. For electrical characteristics, it is those that are guaranteed
under the conditions for each parameter. Even when these are within the recommended operating range, voltage and temperature characteristics are
indicated.
(3) Reverse connection of power supply connector
There is a risk of damaging the LSI by reverse connection of the power supply connector. For protection from reverse connection, take measures such
as externally placing a diode between the power supply and the power supply pin of the LSI .
(4) Power supply lines
In the design of the board pattern, make power supply and GND line wiring low impedance.
When doing so, although the digital power supply and analog power supply are the same potential, separate the digital power supply pattern and analog
power supply pattern to deter digital noise from entering the analog power supply due to the common impedance of the wiring patterns. Similarly take
pattern design into account for GND lines as well.
Furthermore, for all power supply pins of the LSI, in conjunction with inserting capacitors between power supply and GND pins, when using electrolytic
capacitors, determine constants upon adequately confirming that capacitance loss occurring at low temperatures is not a problem for various characteristics
of the capacitors used.
(5) GND voltage
Make the potential of a GND pin such that it will be the lowest potential even if operating below that. In addition, confirm that there are no pins for
which the potential becomes less than a GND by actually including transition phenomena.
(6) Shorts between pins and misinstallation
When installing in the set board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is installed erroneously, there is a
risk of LSI damage. There also is a risk of damage if it is shorted by a foreign substance getting between pins or between a pin and a power supply or
GND.
(7) Operation in strong magnetic fields
Be careful when using the LSI in a strong magnetic field, since it may malfunction.
(8) Inspection in set board
When inspecting the LSI in the set board, since there is a risk of stress to the LSI when capacitors are connected to low impedance LSI pins, be sure to
discharge for each process. Moreover, when getting it on and off of a jig in the inspection process, always connect it after turning off the power supply,
perform the inspection, and remove it after turning off the power supply. Furthermore, as countermeasures against static electricity, use grounding in the
assembly process and take appropriate care in transport and storage.
(9) Input pins
Parasitic elements inevitably are formed on an LSI structure due to potential relationships. Because parasitic elements operate, they give rise to
interference with circuit operation and may be the cause of malfunctions as well as damage. Accordingly, take care not to apply a lower voltage than GND
to an input pin or use the LSI in other ways such that parasitic elements operate. Moreover, do not apply a voltage to an input pin when the power supply
voltage is not being applied to the LSI. Furthermore, when the power supply voltage is being applied, make each input pin a voltage less than the power
supply voltage as well as within the guaranteed values of electrical characteristics.
(10) Ground wiring pattern
When there is a small signal GND and a large current GND, it is reco mmended that you separate the large current GND pattern and small signal GND
pattern and provide single point grounding at the reference point of the set so that voltage variation due to resistance components of the pattern wiring and
large currents do not cause the small signal GND voltage to change. Take care that the GND wiring patte rn of externally attached components also does
not change.
(1 1) Externally attached capacitors
When using ceramic capacitors for externally attached capacitors, determine constants upon taking into account a lowering of the rated capacitance due
to DC bias and capacitance change due to factors such as temperature.
(12) Thermal shutdown circuit (TSD)
When the junction temperature reaches the defined value, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit,
which is aimed at isolating the LSI from thermal runaway as much as p ossible, is not aimed at the protection or guarantee of the LSI. Therefore, do not
continuously use the LSI with this circuit operating or use the LSI assum ing its operation.
(13) Thermal design
Perform therma l design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use.
R1120
A
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
Notice
ROHM Customer Support System
http://www.rohm.com/contact/
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specied herein is subject to change for improvement without notice.
The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specied in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
