250
225
200
175
150
125
100
75
50
25
0
100
90
80
70
60
50
40
30
20
10
0
0.1 1 10 100 1000
I - Load Current - mA
O
Power Loss - mW
Efficiency - %
V = 3.6 V,
V = 1.8 V
I
O
Efficiency
PFM/PWM Operation
Power Loss
PFM/PWM Operation
VIN SW
FB
MODE
GND
EN
VOUT
1.8 V @ 600mA
CI
TPS82671SIP
L
VIN
2.3 V .. 4.8 V
CO
MODE
SELECTION
ENABLE
DC/DC Converter
GND
Copyright © 2016, Texas Instruments Incorporated
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
TPS8267x 600-mA, High-Efficiency MicroSiP™ Step-Down Converter (Profile <1.0mm)
1
1 Features
1 90% Efficiency at 5.5 MHz Operation
17μA Quiescent Current
Wide VIN Range From 2.3 V to 4.8 V
5.5MHz Regulated Frequency Operation
Spread Spectrum, PWM Frequency Dithering
Best in Class Load and Line Transient
±2% Total DC Voltage Accuracy
Automatic PFM/PWM Mode Switching
Low Ripple Light-Load PFM Mode
35dB VIN PSRR (1kHz to 10kHz)
Internal Soft Start, 120-µs Start-Up Time
Integrated Active Power-Down Sequencing
(Optional)
Current Overload and Thermal Shutdown
Protection
Sub 1-mm Profile Solution
Total Solution Size <6.7 mm2
2 Applications
Cell Phones, Smart-Phones
Camera Module, Optical Data Module
Wearable Electronics
Digital TV, WLAN, GPS and Bluetooth™
Applications
POL Applications
3 Description
The TPS8267x device is a complete 600mA, DC/DC
step-down power supply intended for low-power
applications. Included in the package are the
switching regulator, inductor and input/output
capacitors. No additional components are required to
finish the design.
The TPS8267x is based on a high-frequency
synchronous step-down dc-dc converter optimized for
battery-powered portable applications. The
MicroSiP™ DC/DC converter operates at a regulated
5.5-MHz switching frequency and enters the power-
save mode operation at light load currents to maintain
high efficiency over the entire load current range.
The PFM mode extends the battery life by reducing
the quiescent current to 17μA (typ) during light load
operation. For noise-sensitive applications, the device
has PWM spread spectrum capability providing a
lower noise regulated output, as well as low noise at
the input. These features, combined with high PSRR
and AC load regulation performance, make this
device suitable to replace a linear regulator to obtain
better power conversion efficiency.
The TPS8267x is packaged in a compact (2.3mm x
2.9mm) and low profile (1.0mm) BGA package
suitable for automated assembly by standard surface
mount equipment.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
TPS8267x µSIP (8) 2.30 x 2.90 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
spacer Efficiency vs Output Current
spacer
2
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Simplified Schematic............................................. 1
5 Revision History..................................................... 2
6 Device Comparison Table..................................... 4
7 Pin Configuration and Functions......................... 5
8 Specifications......................................................... 5
8.1 Absolute Maximum Ratings ...................................... 5
8.2 ESD Ratings.............................................................. 6
8.3 Recommended Operating Conditions....................... 6
8.4 Thermal Information.................................................. 6
8.5 Electrical Characteristics........................................... 6
8.6 Typical Characteristics.............................................. 8
9 Detailed Description.............................................. 9
9.1 Overview................................................................... 9
9.2 Functional Block Diagram......................................... 9
9.3 Feature Description................................................. 10
9.4 Device Functional Modes........................................ 12
10 Applications and Implementation...................... 13
10.1 Application Information.......................................... 13
10.2 Typical Application ............................................... 13
11 Power Supply Recommendations ..................... 20
12 Layout................................................................... 21
12.1 Layout Guidelines ................................................. 21
12.2 Layout Example .................................................... 21
12.3 Surface Mount Information ................................... 21
13 Device and Documentation Support................. 22
13.1 Documentation Support ........................................ 22
13.2 Related Links ........................................................ 22
13.3 Community Resources.......................................... 22
13.4 Trademarks........................................................... 22
13.5 Electrostatic Discharge Caution............................ 22
13.6 Glossary................................................................ 23
14 Mechanical, Packaging, and Orderable
Information........................................................... 23
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision I (November 2014) to Revision J Page
Added TPS8267195 part number to data sheet .................................................................................................................... 1
Added TPS8267195 to Electrical Characteristics table ......................................................................................................... 7
Changed Layout Example figure, Note 4 value from "...less than 0.5 mm.." to "...less than 0.5 µm.." ............................... 21
Changes from Revision H (October 2014) to Revision I Page
Moved Tstg spec to Absolute Maximum Ratings table for clarification .................................................................................. 5
Changed Handling Ratings to ESD Ratings and replaced MIN/MAX values with ± VALUE for clarification ........................ 6
Added TPS826716 data and removed Product Preview note. .............................................................................................. 7
Changes from Revision G (September 2014) to Revision H Page
Added TPS826716 to Device Comparison Table as Product Preview. ................................................................................. 4
Changes from Revision F (November 2012) to Revision G Page
Added Device Information and Handling Rating tables, Feature Description section, Device Functional Modes,
Application and Implementation section, Power Supply Recommendations section, Layout section, Device and
Documentation Support section, and Mechanical, Packaging, and Orderable Information section. .................................... 1
Added device TPS826721 ..................................................................................................................................................... 4
Changes from Revision E (October 2012) to Revision F Page
Added TPS826745 to Header ................................................................................................................................................ 1
3
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
Changes from Revision D (April 2012) to Revision E Page
Added TPS826765 to Header ................................................................................................................................................ 1
Changes from Revision C (November 2011) to Revision D Page
Added devices TPS82670, TPS82673, and TPS82674 to Header ....................................................................................... 1
Changes from Revision B (August 2011) to Revision C Page
Added device TPS82672 to Header info................................................................................................................................ 1
Changes from Revision A (April 2011) to Revision B Page
Added TPS82676 part number to data sheet header ........................................................................................................... 1
Changes from Original (October 2010) to Revision A Page
Added devices TPS82677 and TPS82678 to Header info..................................................................................................... 1
Added copyright attribution for spectrum illustrations........................................................................................................... 11
4
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com
6 Device Comparison Table
PART NUMBER (1) OUTPUT VOLTAGE DEVICE SPECIFIC FEATURE PACKAGE MARKING
TPS82670 1.86V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge YK
TPS82671 1.8V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage RA
TPS826711 1.8V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge YW
TPS826716 1.6V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage GS
TPS82672 1.5V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage WD
TPS826721 2.1V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage EO
TPS82673 1.26V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge YL
TPS82674 1.2V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge SW
TPS826745 1.225V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge B5
TPS82675 1.2V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage RB
TPS82676 1.1V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge TU
TPS826765 1.05V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage
Output Capacitor Discharge AN
TPS82677 1.2V Output Capacitor Discharge SK
TPS8267195 1.95V PWM Spread Spectrum Modulation
Low PFM Output Ripple Voltage 4A
SIP-8
(TOP VIEW)
SIP-8
(BOTTOMVIEW)
A1
B1
C1
A2
B2
C2
GND
MODE
VOUT
GND
A3
C3
VIN
EN
A3
C3
A2
B2
C2
GND
EN
VIN
GND
C1
VOUT
MODE
A1
B1
5
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
7 Pin Configuration and Functions
space
space
Pin Functions
PIN I/O DESCRIPTION
NAME NO.
VOUT A1 O Power output pin. Apply output load between this pin and GND.
VIN A2, A3 I The VIN pins supply current to the TPS8267x internal regulator.
EN B2 I This is the enable pin of the device. Connect this pin to ground to force the converter into
shutdown mode. Pull this pin to VIto enable the device. This pin must not be left floating and
must be terminated.
MODE B1 I
This is the mode selection pin of the device. This pin must not be left floating and must be
terminated.
MODE = LOW: The device is operating in regulated frequency pulse width modulation mode
(PWM) at high-load currents and in pulse frequency modulation mode (PFM) at light load
currents.
MODE = HIGH: Low-noise mode is enabled and regulated frequency PWM operation is forced.
GND C1, C2, C3 Ground pin.
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
(3) Operation above 4.8V input voltage for extended periods may affect device reliability.
(4) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA(max)) is dependent on the maximum operating temperature (TINT(max)), the
maximum power dissipation of the device in the application (PD(max)), and the junction-to-ambient thermal resistance of the part/package
in the application (RθJA), as given by the following equation: TA(max)= TJ(max)–(RθJA X PD(max)). To achieve optimum performance, it is
recommended to operate the device with a maximum internal temperature of 105°C.
8 Specifications
8.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
VI(2)
Voltage at VIN(3) –0.3 6 V
Voltage at VIN (TPS826721)(3) -0.3 5.5
Voltage at VOUT –0.3 3.6 V
Voltage at EN, MODE –0.3 VIN + 0.3 V
Power dissipation Internally limited
TAOperating temperature range(4) –40 85 °C
TINT (max) Maximum internal operating temperature 125 °C
Tstg Storage temperature –55 125 °C
6
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
(1) Electrostatic discharge (ESD) to measure device sensitivity and immunity to damage caused by assembly line electrostatic discharges in
to the device.
(2) Level listed above is the passing level per ANSI, ESDA, and JEDEC JS-001. JEDEC document JEP155 states that 500-V HBM allows
safe manufacturing with a standard ESD control process.
(3) Level listed above is the passing level per EIA-JEDEC JESD22-C101. JEDEC document JEP157 states that 250-V CDM allows safe
manufacturing with a standard ESD control process.
(4) The machine model is a 200-pF capacitor discharged directly into each pin.
8.2 ESD Ratings VALUE UNIT
VESD(1) Human body model (HBM) ESD stress voltage(2) ±2000 V
Charge device model (CDM) ESD stress voltage(3) ±1000
Machine model (MM) ESD stress voltage(4) ±200 V
(1) Operation above 4.8V input voltage for extended periods may affect device reliability.
(2) In certain applications larger capacitor values can be tolerable, see Output Capacitor Selection section for more details.
8.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT
VIN Input voltage range 2.3 4.8(1) V
IOOutput current range TPS82671 to TPS826765 0 600 mA
Additional output capacitance (PFM/PWM operation)(2)
TPS82670 to TPS82676
TPS826711, TPS826716,
TPS826721, TPS826765,
TPS8267195 0 2.5 µF
TPS82677 0 4 µF
Additional output capacitance (PWM operation)(2) 0 7 µF
TAAmbient temperature –40 +85 °C
TJOperating junction temperature –40 +125 °C
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
8.4 Thermal Information
THERMAL METRIC(1) TPS8267x
UNITSIP
8 PINS
RθJA Junction-to-ambient (top) thermal resistance 125
°C/W
Junction-to-ambient (bottom) thermal resistance 70
RθJCtop Junction-to-case (top) thermal resistance -
RθJB Junction-to-board thermal resistance -
ψJT Junction-to-top characterization parameter -
ψJB Junction-to-board characterization parameter -
RθJCbot Junction-to-case (bottom) thermal resistance -
8.5 Electrical Characteristics
Minimum and maximum values are at VIN = 2.3V to 5.5V, VOUT = 1.8V, EN = 1.8V, AUTO mode and TA= –40°C to 85°C;
Circuit of Parameter Measurement Information section (unless otherwise noted). Typical values are at VIN = 3.6V, VOUT =
1.8V, EN = 1.8V, AUTO mode and TA= 25°C (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY CURRENT
IQOperating quiescent current IO= 0mA. Device not switching 17 40 μA
IO= 0mA. PWM operation 5.8 mA
ISD Shutdown current EN = GND 0.5 5 μA
UVLO Undervoltage lockout threshold TPS8267195 only 2.08 2.14 V
all other versions 2.05 2.1
7
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
Electrical Characteristics (continued)
Minimum and maximum values are at VIN = 2.3V to 5.5V, VOUT = 1.8V, EN = 1.8V, AUTO mode and TA= –40°C to 85°C;
Circuit of Parameter Measurement Information section (unless otherwise noted). Typical values are at VIN = 3.6V, VOUT =
1.8V, EN = 1.8V, AUTO mode and TA= 25°C (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
PROTECTION
Thermal shutdown 140 °C
Thermal shutdown hysteresis 10 °C
ILIM Peak Input Current Limit 1100 mA
ISC Input current limit under short-circuit
conditions VOshorted to ground 13.5 mA
ENABLE, MODE
VIH High-level input voltage 1.0 V
VIL Low-level input voltage 0.4 V
Ilkg Input leakage current Input connected to GND or VIN 0.01 1.5 μA
OSCILLATOR
fSW Oscillator frequency IO= 0mA. PWM operation 4.9 5.45 6.0 MHz
OUTPUT
VOUT Regulated DC
output voltage
TPS82670
TPS82671
TPS826711
TPS826716
TPS82672
TPS826721
TPS82673
TPS82674
TPS826745
TPS82675
TPS82676
TPS826765
2.5V VI4.8V, 0mA IO600 mA
PFM/PWM operation 0.98×VNOM VNOM 1.03×VNOM V
2.5V VI5.5V, 0mA IO600 mA
PFM/PWM operation 0.98×VNOM VNOM 1.04×VNOM V
2.5V VI5.5V, 0mA IO600 mA
PWM operation 0.98×VNOM VNOM 1.02×VNOM V
TPS8267195
2.5V VI4.8V, 0mA IO600 mA
PFM/PWM operation 0.975×VNOM VNOM 1.035×VNOM V
2.5V VI5.5V, 0mA IO600 mA
PFM/PWM operation 0.975×VNOM VNOM 1.045×VNOM V
2.5V VI5.5V, 0mA IO600 mA
PWM operation 0.975×VNOM VNOM 1.025×VNOM V
TPS82677
2.5V VI4.8V, 0mA IO600 mA
PFM/PWM operation 0.98×VNOM VNOM 1.04×VNOM V
2.5V VI5.5V, 0mA IO600 mA
PWM operation 0.98×VNOM VNOM 1.02×VNOM V
Line regulation VI= VO+ 0.5V (min 2.5V) to 5.5V, IO= 200 mA 0.23 %/V
Load regulation IO= 0mA to 600 mA. PWM operation –0.00085 %/mA
Feedback input resistance 480 k
ΔVOPower-save mode
ripple voltage
TPS82671
TPS826711 IO= 1mA, VO= 1.8V 19 mVPP
TPS826716 IO= 1mA, VO= 1.6V 19 mVPP
TPS826721 IO= 1mA, VO= 2.1V 19 mVPP
TPS82673
TPS82674
TPS826745
TPS82675
IO= 1mA, VO= 1.2V 16 mVPP
TPS82676 IO= 1mA, VO= 1.1V 16 mVPP
TPS826765 IO= 1mA, VO= 1.05V 16 mVPP
TPS82677 IO= 1mA, VO= 1.2V 25 mVPP
Start-up time TPS82671
TPS826711 IO= 0mA, Time from active EN to VO120 μs
rDIS Discharge resistor
for power-down
sequence Devices featuring active discharge 70 150
0 40
300 m
250 m
200 m
150 m
100 m
50 m
5 n
Spurious Output Noise (PWM Mode) - V
f - Frequency - MHz
Span = 4 MHz
350 m
400 m
450 m
500 m
V = 2.7 V
I
V = 4.2 V
I
V = 3.6 V
I
0 10
3.5 m
3 m
2.5 m
2 m
1.5 m
1 m
500 m
50 n
Spurious Output Noise (PFM Mode) - V
f - Frequency - MHz
Span = 1 MHz
5 m
4.5 m
5 m
V = 3.6 V
I
V = 2.7 V
I
V = 4.2 V
I
0.01 0.1 1 10 100 1000
f - Frequency - kHz
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
PSRR - Power Supply Rejection Ratio - dB
I = 10 mA
PFM Operation
O
I = 400 mA
PWM Operation
O
I = 150 mA
PWM Operation
O
V -InputVoltage-V
I
I -QuiescentCurrent- A
Qm
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
2.7 3 3.3 3.6 3.9 4.2 4.5 4.8
T =85°C
A
T =25°C
A
T =-40°C
A
6
5.5
5
4.5
4
3.5
3
2.5
2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5
V - Input Voltage - V
I
f - Switching Frequency - MHz
S
I = 150 mA
O
I = 500 mA
O
I = 400 mA
O
I = 300 mA
O
8
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
8.6 Typical Characteristics
Figure 1. Quiescent Current vs. Input Voltage
VO= 1.8 V
Figure 2. PWM Switching Frequency vs. Input Voltage
VI= 3.6 V VO= 1.8 V (TPS82671)
Figure 3. Power Supply Rejection Ratio vs. Frequency VO= 1.8 V RL= 150 Ω(TPS82671)
Figure 4. Spurious Output Noise (PFM Mode) vs. Frequency
VO= 1.8 V RL= 12 Ω(TPS82671)
Figure 5. Spurious Output Noise (PWM Mode) vs. Frequency
VI= 3.6 V VO= 1.8 V (TPS82671)
Figure 6. Output Spectral Noise Density vs. Frequency
Gate Driver
Anti-
Shoot Through
Power Save Mode
Feedback Divider
+
Frequency
Control
R1
R2
L
GND
Soft-Start
EN VIN
Current Limit
Detect
Undervoltage
Lockout
Bias Supply
Bandgap
Thermal
Shutdown
Negative Inductor
Current Detect
VIN
MODE
V = 0.8 V
REF
VREF
CI
1µH
C
4.7 µF
O
Switching
VOUT
DC/DC CONVERTER 2.2 µF
Copyright © 2016, Texas Instruments Incorporated
9
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
9 Detailed Description
9.1 Overview
The TPS8267x is a stand-alone, synchronous, step-down converter. The converter operates at a regulated 5.5-
MHz frequency pulse width modulation (PWM) at moderate to heavy load currents. At light load currents, the
TPS8267x converter operates in power-save mode with pulse frequency modulation (PFM).
The converter uses a unique frequency-locked ring-oscillating modulator to achieve best-in-class load and line
response. One key advantage of the non-linear architecture is that there is no traditional feed-back loop. The
loop response to change in VOis essentially instantaneous, which explains the transient response. Although this
type of operation normally results in a switching frequency that varies with input voltage and load current, an
internal frequency lock loop (FLL) holds the switching frequency constant over a large range of operating
conditions.
Combined with best-in-class load and line-transient response characteristics, the low quiescent current of the
device (approximately 17μA) helps to maintain high efficiency at light load while that current preserves a fast
transient response for applications that require tight output regulation.
The TPS8267x integrates an input current limit to protect the device against heavy load or short circuits and
features an undervoltage lockout circuit to prevent the device from misoperation at low input voltages. Fully
functional operation is permitted down to 2.1V input voltage.
9.2 Functional Block Diagram
PFMModeatLightLoad
PFMRipple
PWMModeatHeavyLoad
NominalDCOutputVoltage
10
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
9.3 Feature Description
9.3.1 Power-Save Mode
If the load current decreases, the converter enters power-save mode automatically. During power-save mode,
the converter operates in discontinuous current, (DCM) single-pulse PFM mode, which produces a low output
ripple compared with other PFM architectures.
When in power-save mode, the converter resumes its operation when the output voltage falls below the nominal
voltage. The converter ramps up the output voltage with a minimum of one pulse and goes into power-save
mode when the output voltage is within its regulation limits.
The IC exits PFM mode and enters PWM mode when the output current can no longer be supported in PFM
mode. As a consequence, the DC output voltage is typically positioned approximately 0.5% above the nominal
output voltage. The transition between PFM and PWM is seamless.
Figure 7. Operation In PFM Mode And Transfer To PWM Mode
9.3.2 Mode Selection
The MODE pin selects the operating mode of the device. Connecting the MODE pin to GND enables the
automatic PWM and power-save mode operation. The converter operates in regulated frequency PWM mode at
moderate to heavy loads, and operates in PFM mode during light loads. This type of operation maintains high
efficiency over a wide load current range.
Pulling the MODE pin high forces the converter to operate in PWM mode even at light-load currents. The
advantage is that the converter modulates its switching frequency according to a spread spectrum PWM
modulation technique that allows simple filtering of the switching harmonics in noise-sensitive applications. In this
mode, the efficiency is lower when compared to the power-save mode during light loads.
For additional flexibility, it is possible to switch from power-save mode to PWM mode during operation. This type
of operation allows efficient power management by adjusting the operation of the converter to the specific system
requirements.
9.3.3 Spread Spectrum, PWM Frequency Dithering
The goal of spread spectrum architecture is to spread out the emitted RF energy over a larger frequency range
so that any resulting electromagnetic interference (EMI) is similar to white noise. The end result is a spectrum
that is continuous and lower in peak amplitude. Spread spectrum makes it easier to comply with EMI standards.
It also makes it easier to comply with the power supply ripple requirements in cellular and non-cellular wireless
applications. Radio receivers are typically susceptible to narrowband noise that is focused on specific
frequencies.
Switching regulators can be particularly troublesome in applications where electromagnetic interference (EMI) is
a concern. Switching regulators operate on a cycle-by-cycle basis to transfer power to an output. In most cases,
the frequency of operation is either fixed or regulated, based on the output load. This method of conversion
creates large components of noise at the frequency of operation (fundamental) and multiples of the operating
frequency (harmonics).
( ) ( )
m c m
B = 2 1 + m = 2 +
¦
´ ¦ ´ ´ D ¦ ¦
c
c
ƒ
=ƒ
D
d
c
ƒ
m
δ ƒ
m = ƒ
´
( )
( )
hmfB
ffmfB
fmh
mcfm
×+××=
+D×=+××=
12
)(212
( ) )(212 mcfm ffmfB +D×=+××=
0dBV
0dBVref
F1
FENV,PEAK Dfc Dfc Non-modulatedharmonic
Side-bandharmonics
windowaftermodulation
11
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
Feature Description (continued)
(1) Spectrum illustrations and formulae (Figure 8 and Figure 9) copyright IEEE TRANSACTIONS ON ELECTROMAGNETIC
COMPATIBILITY, VOL. 47, NO.3, AUGUST 2005. See References Section for full citation.
The spread spectrum architecture varies the switching frequency by approximately ±10% of the nominal
switching frequency, thereby significantly reduces the peak radiated and conducting noise on both the input and
output supplies. The frequency dithering scheme is modulated with a triangle profile and a modulation frequency
fm.
Figure 8. Spectrum Of A Frequency Modulated Sin.
Wave With Sinusoidal Variation In Time Figure 9. Spread Bands Of Harmonics In
Modulated Square Signals (1)
Figure 8 and Figure 9 show that after modulation the sideband harmonic is attenuated when compared to the
non-modulated harmonic, and when the harmonic energy is spread into a certain frequency band. The higher the
modulation index (mf) the larger the attenuation.
(1)
With:
fcis the carrier frequency (i.e. nominal switching frequency)
fmis the modulating frequency (approx. 0.016*fc)
δis the modulation ratio (approx 0.1)
(2)
The maximum switching frequency is limited by the process and by the parameter modulation ratio (δ), together
with fm, which is the bandwidth of the side-band harmonics around the carrier frequency fc. The bandwidth of a
frequency modulated waveform is approximately given by the Carson’s rule and can be summarized as:
(3)
fm< RBW: The receiver is not able to distinguish individual side-band harmonics; so, several harmonics are
added in the input filter and the measured value is higher than expected in theoretical calculations.
fm> RBW: The receiver is able to properly measure each individual side-band harmonic separately, so that the
measurements match the theoretical calculations.
12
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
9.4 Device Functional Modes
9.4.1 Enable
The TPS8267x device starts operation when EN is set high and starts up with the soft start as previously
described. For proper operation, the EN pin must be terminated and must not be left floating.
Pulling the EN pin low forces the device into shutdown. In this mode, all internal circuits are turned off and the
VIN current reduces to the device leakage current, which is typically a few hundred nanoamps.
The TPS8267x device can actively discharge the output capacitor when it turns off. The integrated discharge
resistor has a typical resistance of 100 . The required time to ramp down the output voltage depends on the
load current and the capacitance present at the output node.
9.4.2 Soft Start
The TPS8267x has an internal soft-start circuit that limits the in-rush current during start-up. This circuit limits
input voltage drop when a battery or a high-impedance power source is connected to the input of the MicroSiP™
DC/DC converter.
The soft-start system progressively increases the switching on-time from a minimum pulse-width of 35ns as a
function of the output voltage. This mode of operation continues for approximately 100μs after the enable. If the
output voltage does not reach its target value within the soft-start time, the soft-start transitions to a second mode
of operation.
If the output voltage rises above approximately 0.5V, the converter increases the input current limit and thus
enables the power supply to come up properly. The start-up time mainly depends on the capacitance present at
the output node and the load current.
VIN SW
FB
MODE
GND
EN
CI
TPS8267XSIP
L
VIN
CO
MODE
SELECTION
ENABLE
DC/DC Converter
GND
VOUT
Copyright © 2016, Texas Instruments Incorporated
13
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
10 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The TPS8267x devices are complete power supply modules, not needing further external devices. The devices
are optimized to work best with the components populated. However application conditions might demand for
different input and/or output capacitance values.
10.2 Typical Application
Figure 10. MicroSIP Converter Module Schematic
10.2.1 Design Requirements
For applications requiring additional input and/or output capacitance, the following procedures should be
considered. For the maximum recommended values see Recommended Operating Conditions.
10.2.2 Detailed Design Procedure
10.2.2.1 Input Capacitor Selection
Because of the pulsating input current nature of the buck converter, a low ESR input capacitor is required to
prevent large voltage transients that can cause misbehavior of the device or interference in other circuits in the
system.
For most applications, the input capacitor that is integrated into the TPS8267x should be sufficient. If the
application exhibits a noisy or erratic switching frequency, experiment with additional input ceramic capacitance
to find a remedy.
The TPS8267x uses a tiny ceramic input capacitor. When a ceramic capacitor is combined with trace or cable
inductance, such as from a wall adapter, a load step at the output can induce ringing at the VIN pin. This ringing
can couple to the output and be mistaken as loop instability or can even damage the part. In this circumstance,
additional "bulk" capacitance, such as electrolytic or tantalum, should be placed between the input of the
converter and the power source lead to reduce ringing that can occur between the inductance of the power
source leads and CI.
10.2.2.2 Output Capacitor Selection
The advanced, fast-response, voltage mode, control scheme of the TPS8267x allows the use of a tiny ceramic
output capacitor (CO). For most applications, the output capacitor integrated in the TPS8267x is sufficient.
14
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
At nominal load current, the device operates in PWM mode; the overall output voltage ripple is the sum of the
voltage step that is caused by the output capacitor ESL and the ripple current that flows through the output
capacitor impedance. At light loads, the output capacitor limits the output ripple voltage and provides holdup
during large load transitions.
The TPS8267x is designed as a Point-Of-Load (POL) regulator, to operate stand-alone without requiring any
additional capacitance. Adding a 2.2μF ceramic output capacitor (X7R or X5R dielectric) generally works from a
converter stability point of view, but does not necessarily help to minimize the output ripple voltage.
For best operation (i.e. optimum efficiency over the entire load current range, proper PFM/PWM auto transition),
the TPS8267xSIP requires a minimum output ripple voltage in PFM mode. The typical output voltage ripple is ca.
1% of the nominal output voltage VO. The PFM pulses are time controlled resulting in a PFM output voltage
ripple and PFM frequency that depends (first order) on the capacitance seen at the MicroSiPTM DC/DC
converter's output.
In applications requiring additional output bypass capacitors located close to the load, care should be taken to
ensure proper operation. If the converter exhibits marginal stability or erratic switching frequency, experiment
with additional low value series resistance (e.g. 50 to 100mΩ) in the output path to find a remedy.
Because the damping factor in the output path is directly related to several resistive parameters (e.g. inductor
DCR, power-stage rDS(on), PWB DC resistance, load switches rDS(on) …) that are temperature dependant, the
converter small and large signal behavior must be checked over the input voltage range, load current range and
temperature range.
The easiest sanity test is to evaluate, directly at the converter’s output, the following aspects:
PFM/PWM efficiency
PFM/PWM and forced PWM load transient response
During the recovery time from a load transient, the output voltage can be monitored for settling time, overshoot or
ringing that helps judge the converter’s stability. Without any ringing, the loop has usually more than 45° of phase
margin.
0
10
20
30
40
50
60
70
80
90
100
0.1 1 10 100 1000
V = 3.6 V
Forced PWM Operation
I
V = 4.2 V
PFM/PWM Operation
I
V = 3.6 V
PFM/PWM Operation
I
V = 2.7 V
PFM/PWM Operation
I
I - Load Current - mA
O
Efficiency - %
15
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
10.2.3 Application Curves
VO= 1.95V
Figure 11. Efficiency vs. Load Current
VO= 1.8 V
Figure 12. Efficiency vs. Load Current
VO= 1.2 V
Figure 13. Efficiency vs. Load Current
VO= 1.8 V PFM/PWM Operation
Figure 14. Efficiency vs. Input Voltage
VO= 1.8 V PFM/PWM Operation (TPS82671)
Figure 15. Peak-to-Peak Output Ripple Voltage vs. Load
Current
VO= 1.2 V PFM/PWM Operation (TPS82675)
Figure 16. Peak-to-Peak Output Ripple Voltage vs. Load
Current
16
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
VO= 1.2 V (TPS82671)
Figure 17. Peak-to-Peak Output Ripple Voltage vs. Load
Current
VO= 1.8 V PFM/PWM Operation (TPS82671)
Figure 18. DC Output Voltage vs. Load Current
VO= 1.2 V (TPS82675)
Figure 19. DC Output Voltage vs. Load Current VO= 1.2 V PFM/PWM Operation (TPS82677)
Figure 20. DC Output Voltage vs. Load Current
VO= 1.8 V MODE = Low (TPS82671)
Figure 21. Combined Line/Load Transient Response
VO= 1.8 V MODE = Low (TPS82671)
Figure 22. Combined Line/Load Transient Response
17
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
VO= 1.8 V VI= 3.6 V MODE = Low (TPS82671)
Figure 23. Load Transient Response in PFM/PWM
Operation
VO= 1.8 V VI= 3.6 V MODE = Low (TPS82671)
Figure 24. Load Transient Response in PFM/PWM
Operation
VO= 1.8 V VI= 2.7 V MODE = Low (TPS82671)
Figure 25. Load Transient Response in PFM/PWM
Operation
VO= 1.8 V VI= 4.5 V MODE = Low (TPS82671)
Figure 26. Load Transient Response in PFM/PWM
Operation
VO= 1.8 V VI= 3.6 V MODE = Low (TPS82671)
Figure 27. Load Transient Response in PFM/PWM
Operation
VO= 1.8 V VI= 2.7 V MODE = Low (TPS82671)
Figure 28. Load Transient Response in PFM/PWM
Operation
18
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
VO= 1.8 V VI= 4.5 V MODE = Low (TPS82671)
Figure 29. Load Transient Response in PFM/PWM
Operation
VO= 1.8 V VI= 3.6 V MODE = Low (TPS82671)
Figure 30. AC Load Transient Response
VO= 1.2 V VI= 3.6 V MODE = Low
Figure 31. Load Transient Response in PFM/PWM
Operation
VO= 1.2 V VI= 3.6 V MODE = Low
Figure 32. Load Transient Response in PFM/PWM
Operation
VO= 1.2 V VI= 2.7 V MODE = Low
Figure 33. Load Transient Response in PFM/PWM
Operation
VO= 1.2 V VI= 4.5 V MODE = Low
Figure 34. Load Transient Response in PFM/PWM
Operation
19
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
VO= 1.2 V VI= 3.6 V MODE = Low
Figure 35. Load Transient Response in PFM/PWM
Operation
VO= 1.2 V VI= 2.7 V MODE = Low
Figure 36. Load Transient Response in PFM/PWM
Operation
VO= 1.2 V VI= 4.5 V MODE = Low (TPS82671)
Figure 37. Load Transient Response in PFM/PWM
Operation
VO= 1.2 V VI= 3.6 V MODE = Low (TPS82671)
Figure 38. AC Load Transient Response
VO= 1.8 V (TPS82671)
Figure 39. PFM/PWM Boundaries
VO= 1.2 V (TPS82674)
Figure 40. PFM/PWM Boundaries
20
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
Typical Application (continued)
VO= 1.8 V VI= 3.6 V IO= 0 mA
MODE = Low
Figure 41. Start-Up
VO= 1.8 V VI= 3.6 V (TPS82671)
RL= 100 ΩMODE = Low
Figure 42. Start-Up
11 Power Supply Recommendations
The TPS8267X devices are designed to operate from a 2.3-V to 4.8-V input voltage supply. The input power
supply's output current needs to be rated according to the output voltage and the output current of the power rail
application.
Copper Trace Width
Solder Pad Width
Solder Mask Opening
Copper Trace Thickness
Solder Mask Thickness
M0200-01
21
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
(1) Circuit traces from non-solder-mask defined PWB lands should be 75 μm to 100 μm wide in the exposed area inside the solder mask
opening. Wider trace widths reduce device stand off and affect reliability.
(2) Best reliability results are achieved when the PWB laminate glass transition temperature is above the operating the range of the
intended application.
(3) Recommend solder paste is Type 3 or Type 4.
(4) For a PWB using a Ni/Au surface finish, the gold thickness should be less than 0.5 µm to avoid a reduction in thermal fatigue
performance.
(5) Solder mask thickness should be less than 20 μm on top of the copper circuit pattern.
(6) For best solder stencil performance use laser cut stencils with electro polishing. Chemically etched stencils give inferior solder paste
volume control.
12 Layout
12.1 Layout Guidelines
In making the pad size for the µSiP LGA balls, it is recommended that the layout use non-solder-mask defined
(NSMD) land. With this method, the solder mask opening is made larger than the desired land area, and the
opening size is defined by the copper pad width. Figure 43 shows the appropriate diameters for a MicroSiPTM
layout.
12.2 Layout Example
Figure 43. Recommended Land Pattern Image And Dimensions
SOLDER PAD
DEFINITIONS(1)(2)(3)(4) COPPER PAD SOLDER MASK (5)
OPENING COPPER
THICKNESS STENCIL (6)
OPENING STENCIL THICKNESS
Non-solder-mask
defined (NSMD) 0.30mm 0.360mm 1oz max (0.032mm) 0.34mm diameter 0.1mm thick
12.3 Surface Mount Information
The TPS8267x MicroSiP™ DC/DC converter uses an open frame construction that is designed for a fully
automated assembly process and that features a large surface area for pick and place operations. See the "Pick
Area" in the package drawings.
Package height and weight have been kept to a minimum thereby to allow the MicroSiP™ device to be handled
similarly to a 0805 component.
See JEDEC/IPC standard J-STD-20b for reflow recommendations.
22
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
SLVSAI0J OCTOBER 2010REVISED MAY 2016
www.ti.com
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation Feedback Copyright © 2010–2016, Texas Instruments Incorporated
13 Device and Documentation Support
13.1 Documentation Support
13.1.1 References
"EMI Reduction in Switched Power Converters Using Frequency Modulation Techniques", in IEEE
TRANSACTIONS ON ELECTROMAGNETIC COMPATIBILITY, VOL. 4, NO. 3, AUGUST 2005, pp 569-576 by
Josep Balcells, Alfonso Santolaria, Antonio Orlandi, David González, Javier Gago.
13.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL
DOCUMENTS TOOLS &
SOFTWARE SUPPORT &
COMMUNITY
TPS82670 Click here Click here Click here Click here Click here
TPS82671 Click here Click here Click here Click here Click here
TPS82672 Click here Click here Click here Click here Click here
TPS82673 Click here Click here Click here Click here Click here
TPS82674 Click here Click here Click here Click here Click here
TPS82675 Click here Click here Click here Click here Click here
TPS82676 Click here Click here Click here Click here Click here
TPS82677 Click here Click here Click here Click here Click here
TPS826711 Click here Click here Click here Click here Click here
TPS826716 Click here Click here Click here Click here Click here
TPS826721 Click here Click here Click here Click here Click here
TPS826745 Click here Click here Click here Click here Click here
TPS826765 Click here Click here Click here Click here Click here
TPS8267195 Click here Click here Click here Click here Click here
13.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.4 Trademarks
MicroSiP, E2E are trademarks of Texas Instruments.
Bluetooth is a trademark of Bluetooth SIG, Inc.
All other trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
23
TPS82670
,
TPS82671
,
TPS82672
,
TPS82673
,
TPS82674
,
TPS82675
,
TPS82676
TPS82677
,
TPS826711
,
TPS826716
,
TPS826721
,
TPS826745
,
TPS826765
,
TPS8267195
www.ti.com
SLVSAI0J OCTOBER 2010REVISED MAY 2016
Product Folder Links: TPS82670 TPS82671 TPS82672 TPS82673 TPS82674 TPS82675 TPS82676 TPS82677
TPS826711 TPS826716 TPS826721 TPS826745 TPS826765 TPS8267195
Submit Documentation FeedbackCopyright © 2010–2016, Texas Instruments Incorporated
13.6 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
PACKAGE OPTION ADDENDUM
www.ti.com 3-Sep-2018
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TPS82670SIPR ACTIVE uSiP SIP 8 3000 RoHS (In
Work) & Green
(In Work)
Call TI Call TI -40 to 85 YK
TXI670
TPS82670SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 YK
TXI670
TPS826711SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 YW
TXI671
TPS826711SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 YW
TXI671
TPS826716SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 GS
(TXI671, TXI6716)
TPS826716SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 GS
(TXI671, TXI6716)
TPS82671SIPR ACTIVE uSiP SIP 8 3000 Green (RoHS
& no Sb/Br) SnAgCu Level-2-260C-1 YEAR -40 to 85 RA
TXI671
TPS82671SIPT ACTIVE uSiP SIP 8 250 Green (RoHS
& no Sb/Br) SnAgCu Level-2-260C-1 YEAR -40 to 85 RA
TXI671
TPS826721SIPR ACTIVE uSiP SIP 8 3000 Green (RoHS
& no Sb/Br) Call TI Level-2-260C-1 YEAR -40 to 85 EO
TXI672
TPS826721SIPT ACTIVE uSiP SIP 8 250 Green (RoHS
& no Sb/Br) Call TI Level-2-260C-1 YEAR -40 to 85 EO
TXI672
TPS82672SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 WD
TXI672
TPS82672SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 WD
TXI672
TPS82673SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 YL
TXI673
TPS82673SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 YL
TXI673
TPS826745SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 B5
TXI674
TPS826745SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 B5
TXI674
TPS82674SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 SW
PACKAGE OPTION ADDENDUM
www.ti.com 3-Sep-2018
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
TXI674
TPS82674SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 SW
TXI674
TPS82675SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 RB
TXI675
TPS82675SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 RB
TXI675
TPS826765SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 AN
TXI676
TPS826765SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 AN
TXI676
TPS82676SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 TU
TXI676
TPS82676SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 TU
TXI676
TPS82677SIPR ACTIVE uSiP SIP 8 3000 TBD Call TI Call TI -40 to 85 SK
TXI677
TPS82677SIPT ACTIVE uSiP SIP 8 250 TBD Call TI Call TI -40 to 85 SK
TXI677
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
PACKAGE OPTION ADDENDUM
www.ti.com 3-Sep-2018
Addendum-Page 3
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TPS826721SIPR uSiP SIP 8 3000 178.0 9.0 2.45 3.05 1.1 4.0 8.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 6-May-2018
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TPS826721SIPR uSiP SIP 8 3000 223.0 194.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 6-May-2018
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
TPS82670SIPR TPS82670SIPT