AEC - Q200 Qualified ZCM Series Datasheet SMD Precision Metal Film Resistors | MELF Style APPLICATIONS ORDERING CODE-Example New SAP Part Nr.: ZCM Serie 207 Power rating 204 = 0,4W 207 = 1,0W F K E 07- 1K AA Tol. Pack-Code TCR Forming type R Value Special B = 0,1% C = 0,25% D = 0,5% F = 1% G = 2% J = 5% K = Blister tape reel C = 15ppm D = 25ppm E = 50ppm F = 100ppm 07- = 07 inch (Reel diameter) or 13- = 13 inch (Reel diameter) AA = Standard Type 0207 F K E 07 1K Size Tol. K = Blister tape reel TC Reel diam. R Value Charger Alternative Energy Power Supply Home Appliances Industrial FEATURES Precision MELF resistor Advanced MELF technology Excellent stability in different environmental conditions Best in class pulse load capability AEC - Q200 Qualified Intrinsic sulfur resistance RoHs & REACH Compliant Historical VTM Part Nr.: ZC Automotive ELECTRICAL SPECIFICATIONS ZCM204 ZCM207 SMD ZC0204 ZC0207 [W] 0,4 0R22 ... 10M 1,0 0R16 ... 10M Type Historical Part Number Nominal Power Rating P70 Resistance Range [] (Other values upon request) E-Series Tolerances Temperature Coefficient E24 / E96 / E192 [%] B = 0,1% , C = 0,25% , D = 0,5% , F = 1% , G = 2% , J = 5% -6* -1 [10 K ] Depends on the value, please check the table below Working Temperature Range [C] -55 ... +155 Permissible film temperature [C] 155 IEC60115-1 clause 4.2 ; 4.8 (+20 / -55[C] and (+20 / +125[C]) (F max.) Max. Working Voltage Dielectric Withstanding Voltage IEC115-1 clause 4.7 (1[min]) [AC or DC]RMS 200 350 [V]RMS 300 500 DIMENSIONS [mm] ZCM204 ZCM207 Historical P/N: ZC0204 ZC0207 L O D L1 O 3,6 +0 /-0,2 1,4 +0 /-0,1 1,8 min. 5,8 +0 /-0,3 2,2 0,2 2,6 min. D1 D +0 /-0,15 D +0 /-0,2 A MASS 0,80 0,10 1,25 0,2 22 77 (mg) Recommended solder pads dimensions Type ZCM204 ZCM207 Wave soldering I 1,5 2,4 a 1,5 2,3 b 1,8 2,6 Reflow soldering c 4,5 7,0 I 1,7 2,6 a 1,2 2,0 b 1,6 24 c 4,1 6,6 File Nr. 3900.18-450.113.16 | Revision: 201710 Type 1 1 ZCM Series Datasheet PERFORMANCE DATE ZCM204 Type Historical Part Number Climatic Category Short Time Overload Periodic electric overload IEC60115-1 clause 4.39 ,0.1[s]on, 2.5[s]off,1000 cycles Failure Rate (U=15* [%] [%] Standard operation Power operation [%] -9 Endurance at 70C, IEC60115-1 clause 4.25.1 Umax,, 1,5[h]ON ; 0,5[h]OFF) 0,03 (1M) ; 0,1 (>1M) 0,03 (1M) ; 0,15 (>1M) 0,05 (1M) ; 0,1 (>1M) 0,05 (1M) ; 0,15 (>1M) 0,15 0,25 0,15 0,5 0,15 0,15 0,3 0,3 -1 [10 h ] (Total, 0 , max, 60[%] cont. lev.) Precision operation [%] Standard operation [%] Power operation [%] Endurance at upper Category Temp. IEC60115-1 clause 4.25.3 [%] ( 1000[h] Damp Heat, Steady State IEC60115-1 clause 4.24 2 ZC0207 55/155/56 Standard operation IEC60115-1 clause 4.13 Power (U=2,5* , 2* Umax, 5 [s]) operation Single pulse high voltage overload Standard operation IEC60115-1 clause 4.27 Power (U=10* ,Severity 4, 10 pulses 10[s]/700[s] operation (U= ZCM207 ZC0204 0,1 1000h 8000h 1000h 8000h 1000h 8000h 125C 0.05 (10R1M) 0.1 (10R1M) 0.15 (<10R) ; 0.1 (10R1M) ; 0.25 (>1M) 0.3 (<10R) ; 0.2 (10R1M) ; 0.5 (>1M) 0.25 0.5 0.15 (<10R) ; 0.1 (10R1M) ; 0.25 (>1M) 0.05 (10R1M) 0.1 (10R1M) 0.15 (1M) ; 0.5 (>1M) 0.3 (1M) ; 1 (>1M) 0,25 (1M) ; 0,5 (>1M) 0,5 (1M) ; 1 (>1M) 0,15 (1M) ; 0,5 (>1M) 155C 0.3 (<10R) ; 0.2 (10R1M) ; 0.5 (>1M) 0,3 (1M) ; 1 (>1M) [%] 0,15 ( 1M) ; 0,25 (>1M) 0,25 ( 1M) ; 1 (>1M) [%] 0,25 ( 1M) ; 2 (>1M) 0,5 ( 1M) ; 2 (>1M) -55~125C 0,15 ( 1M) ; 0,25 (>1M) 0,25 -55~155C 0,5 0,5 [%] 0,05 ( 1M) ; 0,1 (>1M) 0,05 [%] 0,1 ( 10R) ; 0,05 (>10R) 0,1 ( 10R) ; 0,05 (>10R) [%] 0,5 [2 kV] 0,5 [4 kV] 3 (40 [C], 93 [% r.h.], 56[d]) Damp Heat, Steady State, Accelerated IEC60115-1 clause 4.37 2 5 (85 [C], 85 [%RH], U = 0.3* ) Temperature Cycling IEC60068-2-14 ; IEC60115-1 clause 4.19 [%] ( 30[min] each , 1000 cycles) Vibration IEC60068-2-6 ; IEC60115-1 clause 4.22 2 (10;2000[Hz], 1,5[mm] , or 200[m/s ] 7,5[h]) Resistance to Soldering Heat IEC60115-1 clause 4.18 5 1 (260 [C], 10 [s])Solder bath method Electrostatic Discharge IEC60115-1 clause 4.38 ; IEC61340-3-1 ( 3 positives + 3 negatives discharges) Voltage proof IEC60115-1 clause 4.7 No flash over or breakdown URMS=UINS, 60 [s] Flammability IEC60115-1 clause 4.35, IEC60695-11-5 No burning after 30[s] Needle flame test, 10[s] Solderability IEC60068-2-20 ; IEC60115-1 clause 4.17 3 (235 [C] 2 0,2 95% covered, no visible damage [s],SnAg3Cu0.5 or SnAg3.5) Component Resistance to Solvents IEC60068-2-45 ; IEC60115-1 clause 4.29 No visible damage Resistance to solvents of Marking IEC60068-2-45 ; IEC60115-1 clause 4.30 Marking visible , no visible damage (50[C] method 1) Marking IEC60062 Color code NOTES: MARKING [COLOR CODE]: * ZCM204 Color code marking is applied according to IEC 60062 in four bands (E24 series) for 5 % tolerance, or in five bands (E96 or E192 series). Each color band appears as a single solid line, voids are permissible if at least 2/3 of the band is visible from each radial angle of view. The last color band for tolerance is approximately 50 % wider than the other bands. * ZCM207 Color code marking is applied according to IEC 60062 in four (E24 series) or six bands (E96 series). Each color band appears as a single solid line, voids are permissible if at least 2/ of the band is visible from each radial angle of view. The last color band represents the TCR for resistors with TCR 50 ppm/K and nominal tolerance 1 %. 3 Zero ohm jumpers are marked with one centered black band. File Nr. 3900.18-450.113.16 | Revision: 201710 (50[C] method 2) 1 2 ZCM Series Datasheet TEMPERATURE COEFFICIENT ZCM204 ZCM207 Resistance range Tolerance TCR E-Series 0R16 ... 0R91 5% 0R22 ... 0R91 100 ppm/K E24 0R22 ... 0R91 2% 0R82... 10M 1R... 10M 1% E24 / E96 50 ppm/K 10R... 1M65 1R... 2M21 0,5% E24 / E192 10R... 1M65 43R... 1M 0,5% 22R... 1M65 43R... 1M 0,25% 25 ppm/K E24 / E192 22R... 1M65 43R... 1M 0,1% Notes : 221K is light green for100R... 0,5% of 50 ppm/K or 100 ppm/K, pink for 25 ppm/K, or violet for 15 ppm/K. * ZCM204 - The color of the10R... body coating jumpers511K and for a temperature coefficient * ZCM207 - TCR 10 ppm/K 22R... and 221K 5 ppm/K in resistance 100R... range 100 511Kto 100k on request. 0,25% 15 ppm/K E24 / E192 * Zero ohm jumper - Are marked one centered black band. 43R...with 221K 100R... 511K 0,1% Jumper Imax = 3A Jumper Imax = 5A 10 m NOTES: RESISTOR BODY COLOR CODE: * The body coating color is light green for jumpers and for a temperature coefficient of 50 or 100 [ppm], pink for 25[ppm] and violet for 15[ppm] MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION OPERATION MODE Rated Power dissipation P70 [W] Operating temp. range [C] Permissible film temperature F Max [C] Resistance range 1000h Max. Resistance drift [%] 8000h [R/R] 225 000h * PRECISION 0,07 -10 to 85 85 10R - 1M 0,05 0,1 0,25 ZCM204 STANDARD 0,25 -55 to 125 125 R22 - 1M 0,15 0,3 0,75 POWER 0,4 -55 to 155 155 R22 - 10M 0,25 0,5 - PRECISION 0,125 -10 to 85 85 100R - 511K 0,05 0,1 0,25 ZCM207 STANDARD 0,4 -55 to 125 125 1R0 - 1M 0,15 0,3 1,0 POWER 1,0 -55 to 155 155 1R0 - 1M 0,25 0,5 - A suitable low thermal resistance of the circuit board assembly must be safeguarded in order to maintain the film temperature of the resistors within the specified limits. PERFORMANCE GRAPH's Derating - Power Operation Derating - Standard Operation Non- Linearity File Nr. 3900.18-450.113.16 | Revision: 201710 Derating - Precision Operation 1 3 ZCM Series Datasheet Single Pulse for R < 10 Single Pulse for R 10 Single Pulse (1.2/50 [s]) Pulse Voltage Continuous Pulse for R < 10 Continuous Pulse for R 10 Single Pulse (10/700 [s]) File Nr. 3900.18-450.113.16 | Revision: 201710 Current Noise 1 4 ZCM Series Datasheet PACKAGING - Blister tape The type ZCM is packed in antistatic blister tape according to IEC60286-3, type 2a, packing details described below, ZCM204 ZCM207 W1 W2 [1,5] [max] 8,4 14,4 12,4 18,4 A0 B0 F W D1 T2 1,550,1 3,70,1 3,50,05 8,0.0,3 1,0 1,8 ZCM207 2,400,1 6,00,1 5,50,05 12,0.0,3 1,5 2,7 Type ZCM204 ZCM207 ZCM204 ZCM207 Packaging [dimensions] Quantity [pcs] 07(inch) Blister tape 3000 13(inch) Blister tape 10000 1500 7500 File Nr. 3900.18-450.113.16 | Revision: 201710 Type Type ZCM204 1 5