PE30
www.vishay.com Vishay Sfernice
Revision: 14-Aug-13 1Document Number: 51037
For technical questions, contact:
sferpottrimmers@vishay.com
, see also Application Note:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fully Sealed Potentiometer Military and Professional Grade
FEATURES
High power rating 3 W at 70 °C
Low temperature coefficient (150 ppm/°C
typical)
Cermet element
Full sealing
Use of faston 2.86 connections
Tests according to CECC 41000 or IEC 60393-1
Wires and connectors available
Custom design on request
Center detent option
Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")
20 (0.79) max.
PE30L 12 (0.47)
8
(0.31)
Ø 19.7
(0.78)
13 (0.51)
max.
14 wrench
Thread M10 x 0.75 Ø 6
(0.24)
76°
R 5.2
(0.20)
ac
b
3
(0.12)
2.85 (0.11)
0.5
(0.02)
FG = 16 (0.63)
FL = 25 (0.99) FR = 50 (1.97)
3
(0.12)
Ø 1.8 (0.07)
3
(0.12)
12.5
(0.49)
8.8
(0.35)
2.3
(0.9)
0.8
(0.3)
PE30LL: LPRP - Locating Peg
9.2
(0.36)
Ø 3.5
(0.14)
Ø 10.5
(0.41)
PANEL MOUNT
PE30ME: Panel Sealed
Ø 1.2
(0.05) Ø 6
(0.24)
Flats
located
FP = 47 (1.85)
FJ = 22 (0.87)
FD = 13
(0.61)
9 (0.35)
Sealing ring
8 ± 0.2
(0.31 ± 0.01) Ø 10.5
(0.41)
Ø 19.7
(0.78)
Ø 1 (0.4)
0.7 (0.03)
16 (0.63) max.
23 (0.91) max.
PANEL MOUNT
Slot
1 x 1.8
deep
PE30
www.vishay.com Vishay Sfernice
Revision: 14-Aug-13 2Document Number: 51037
For technical questions, contact:
sferpottrimmers@vishay.com
, see also Application Note:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ELECTRICAL SPECIFICATIONS
Resistive Element Cermet
Electrical Travel 270° ± 10°
Resistance Range Linear Taper 22 to 10 M
Logarithmic Taper 100 to 2.2 M
Standard Series E3 1 - 2.2 - 4.7 and on request 1 - 2 - 5
Tolerance Standard ± 20 %
On Request ± 10 % to ± 5 %
Taper
Power Rating Linear
Logarithmic
3 W at 70 °C
1.5 W at 70 °C
Circuit Diagram
Temperature Coefficient (Typical) ± 150 ppm/°C
Limiting Element Voltage 300 V
Contact Resistance Variation (Typical) 3 % Rn or 3
End Resistance (Typical) 1
Dielectric Strength (RMS) 2500 V
Insulation Resistance (300 VDC)10
5 M
Independent Linearity (Typical) ± 5 %
100
80
60
40
20
00 10080604020
% CLOCKWISE SHAFT ROTATION
% TOTAL RESISTANCE
F
L
A
AMBIENT TEMPERATURE IN °C
POWER IN W
0 20 40 60 70 80 100 120 140
0
3
LIN. TAPER A
1
2
LOG. TAPER
L and F
a
(1)
b
(2)
c
(3)
cw
PE30
www.vishay.com Vishay Sfernice
Revision: 14-Aug-13 3Document Number: 51037
For technical questions, contact:
sferpottrimmers@vishay.com
, see also Application Note:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
STANDARD RESISTANCE ELEMENT DATA
STANDARD
RESISTANCE
VALUES
LINEAR TAPER LOGS TAPER
MAX.
POWER
AT 70 °C
MAX.
WORKING
VOLTAGE
MAX. CUR.
THROUGH
WIPER
MAX.
POWER
AT 70 °C
MAX.
WORKING
VOLTAGE
MAX. CUR.
THROUGH
WIPER
WVmAWVmA
22
47
100
220
470
1K
2.2K
4.7K
10K
22K
47K
100K
220K
470K
1M
2.2M
4.7M
10M
3
3
3
3
3
3
3
3
3
3
1.91
0.90
0.41
0.19
0.09
0.04
0.02
0.01
8.1
11.9
17.3
25.7
37.5
54.8
81.2
119.9
173
257.7
300
300
300
300
300
300
300
300
369
252
173
116
79
54
37
25
17
11
6.3
3
1.36
0.63
0.30
0.13
0.06
0.03
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
0.9
0.41
0.19
0.09
0.04
12.2
18.2
26.6
38.7
57.4
83.9
122
181.6
265
300
300
300
300
300
122
82.6
56.6
38.7
26.1
17.9
12.2
8.25
5.64
3
1.36
0.63
0.30
0.13
MECHANICAL SPECIFICATIONS
Mechanical Travel 300° ± 5°
Operating Torque (Typical) 3 Ncm max. 4.25 oz.-inch max.
End Stop Torque 120 Ncm max. 10.51 lb oz.-inch max.
Tightening Torque of Mounting Nut 250 Ncm max. 22 lb-inch max.
Unit Weight 23 g to 32 g max. 0.8 oz. to 1.13 oz.
Terminals e3: Pure Sn
ENVIRONMENTAL SPECIFICATIONS
Temperature Range - 55 °C to 125 °C
Climatic Category 55/125/56
Sealing Fully sealed - Container IP67
OPTIONS
Special Feature Command Shaft
Length is measured from the mounting surface to the free end of the shaft. The screwdriver
slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to
drawings supplied by customers. We recommend that customers should not machine tool
shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided.
Panel Sealing (PE30M)
The panel sealing device consists of a ring located in a groove on the potentiometer face.
Sealing is obtained by tightening the ring against the panel when mounting the
potentiometer.
Old code: PE30P
Locating Peg (PE30LL) Location is obtained by fitting a special washer on the mounting face of the potentiometer.
Old code: LPRP
Shaft Locking (PE30LD)
The shaft locking device consists of a tapered nut tightening a slotted notched washer
against both bushing and shaft.
DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm.
DBAN is also available with all special types.
This device is normally supplied in a separate bag. Can be pre-mounted on request.
Assembling
Method
1) 2)
6.5
15
14 wrench
12 wrench
PE30
www.vishay.com Vishay Sfernice
Revision: 14-Aug-13 4Document Number: 51037
For technical questions, contact:
sferpottrimmers@vishay.com
, see also Application Note:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CENTER DETENT
Stable position in mid mechanical travel
Output ratio 50 % ± 10 %
Rotational life: 10 000 actuations
ORDERING INFORMATION (First order only)
MARKING
Vishay trademark
Part number (including ohmic value and tolerance code)
Manufacturing date code
Marking of terminals 3, and a, b, c
PERFORMANCE
TESTS CONDITIONS TYPICAL VALUES AND DRIFTS
RT/RT (%) R1-2/R1-2 (%) OTHER
Electrical Endurance 1000 h at rated power
90'/30' - ambient temp. 70 °C ± 1 % - Contact res. variation: < 3 % Rn
Climatic Sequence
Phase A dry heat 125 °C
Phase B damp heat
Phase C cold - 55 °C
Phase D damp heat 5 cycles
± 0.5 % ± 1 % -
Damp Heat, Steady State 56 days
40 °C 93 % HR ± 0.5 % ± 1 % Insulation resistance: > 104 M
Change of Temperature 5 cycles
- 55 °C at + 125 °C ± 0.5 % - -
Mechanical Endurance 25 000 cycles ± 3 % - Contact res. variation: < 2 % Rn
Shock
50 g’s at 11 ms
3 successive shocks
in 3 directions
± 0.1 % ± 0.2 % -
Vibration
10 Hz to 55 Hz
0.75 mm or 10 g’s
during 6 h
± 0.1 % ± 0.2 % -
Full CW Full CCW
CV1M
PE30
www.vishay.com Vishay Sfernice
Revision: 14-Aug-13 5Document Number: 51037
For technical questions, contact:
sferpottrimmers@vishay.com
, see also Application Note:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
MODEL BUSHING OPTION SHAFT OHMIC
VALUE TOLERANCE TAPER PACKAGING SPECIAL
NUMBER
PE30 L =
M10 x 0.75
M = Panel
sealed
M10 x 0.75
0 = none
For L bushing
D = DBAN
L = LPRP
B = DBAN
and LPRP
For M bushing
E = Peg
A = Peg
and DBAN
For L bushing (= old codes:)
FG 16 mm, slotted = AC
FL 25 mm, slotted = AM
FR 50 mm, plain = AL
For M bushing
FD = 13 mm, slotted = AC
FJ = 22 mm, slotted = AM
FP = 47 mm, plain = AL
A law =
from 22
to 10 M
L and F
laws =
from 100
to 2.2 M
± 20 %
On request:
± 10 %
± 5 %
A = Linear
L = Clockwise
logarithmic
F = Clockwise
inverse
logarithmic
B = Box of
10 pieces
(if applicable)
Given by
Vishay
for custom
design
or
E105
CV1M
PART NUMBER DESCRIPTION (for information only)
PE30 LPRP AC 200K 20 % A DBAN CV1M BO e3
MODEL FEATURES OPTION SHAFT VALUE TOL. TAPER OPTION SPECIAL DETENT PACKAGING CUSTOM
SHAFT SPECIAL LEAD
(Pb)-FREE
LBFG204 A3P 0E MB
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 02-Oct-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.