PE30L0FL202MAB - VISHAY SFERNICE

PE30

www.vishay.com Vishay Sfernice

Revision: 14-Aug-13 1Document Number: 51037

For technical questions, contact:

sferpottrimmers@vishay.com

, see also Application Note:

www.vishay.com/doc?51001

and

www.vishay.com/doc?52029

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Fully Sealed Potentiometer Military and Professional Grade

FEATURES

• High power rating 3 W at 70 °C

• Low temperature coefficient (150 ppm/°C

typical)

• Cermet element

• Full sealing

• Use of faston 2.86 connections

• Tests according to CECC 41000 or IEC 60393-1

• Wires and connectors available

• Custom design on request

• Center detent option

• Material categorization: For definitions of compliance

please see www.vishay.com/doc?99912

DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")

20 (0.79) max.

PE30L 12 (0.47)

(0.31)

Ø 19.7

(0.78)

13 (0.51)

max.

14 wrench

Thread M10 x 0.75 Ø 6

(0.24)

76°

R 5.2

(0.20)

(0.12)

2.85 (0.11)

0.5

(0.02)

FG = 16 (0.63)

FL = 25 (0.99) FR = 50 (1.97)

(0.12)

Ø 1.8 (0.07)

(0.12)

12.5

(0.49)

8.8

(0.35)

2.3

(0.9)

0.8

(0.3)

PE30LL: LPRP - Locating Peg

9.2

(0.36)

Ø 3.5

(0.14)

Ø 10.5

(0.41)

PANEL MOUNT

PE30ME: Panel Sealed

Ø 1.2

(0.05) Ø 6

(0.24)

Flats

located

FP = 47 (1.85)

FJ = 22 (0.87)

FD = 13

(0.61)

9 (0.35)

Sealing ring

8 ± 0.2

(0.31 ± 0.01) Ø 10.5

(0.41)

Ø 19.7

(0.78)

Ø 1 (0.4)

0.7 (0.03)

16 (0.63) max.

23 (0.91) max.

PANEL MOUNT

Slot

1 x 1.8

deep

PE30

www.vishay.com Vishay Sfernice

Revision: 14-Aug-13 2Document Number: 51037

For technical questions, contact:

sferpottrimmers@vishay.com

, see also Application Note:

www.vishay.com/doc?51001

and

www.vishay.com/doc?52029

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ELECTRICAL SPECIFICATIONS

Resistive Element Cermet

Electrical Travel 270° ± 10°

Resistance Range Linear Taper 22  to 10 M

Logarithmic Taper 100  to 2.2 M

Standard Series E3 1 - 2.2 - 4.7 and on request 1 - 2 - 5

Tolerance Standard ± 20 %

On Request ± 10 % to ± 5 %

Taper

Power Rating Linear

Logarithmic

3 W at 70 °C

1.5 W at 70 °C

Circuit Diagram

Temperature Coefficient (Typical) ± 150 ppm/°C

Limiting Element Voltage 300 V

Contact Resistance Variation (Typical) 3 % Rn or 3 

End Resistance (Typical) 1 

Dielectric Strength (RMS) 2500 V

Insulation Resistance (300 VDC)10

5 M

Independent Linearity (Typical) ± 5 %

100

00 10080604020

% CLOCKWISE SHAFT ROTATION

% TOTAL RESISTANCE

AMBIENT TEMPERATURE IN °C

POWER IN W

0 20 40 60 70 80 100 120 140

LIN. TAPER A

LOG. TAPER

L and F

(1)

(2)

(3)

PE30

www.vishay.com Vishay Sfernice

Revision: 14-Aug-13 3Document Number: 51037

For technical questions, contact:

sferpottrimmers@vishay.com

, see also Application Note:

www.vishay.com/doc?51001

and

www.vishay.com/doc?52029

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

STANDARD RESISTANCE ELEMENT DATA

STANDARD

RESISTANCE

VALUES

LINEAR TAPER LOGS TAPER

MAX.

POWER

AT 70 °C

MAX.

WORKING

VOLTAGE

MAX. CUR.

THROUGH

WIPER

MAX.

POWER

AT 70 °C

MAX.

WORKING

VOLTAGE

MAX. CUR.

THROUGH

WIPER

WVmAWVmA

100

220

470

2.2K

4.7K

10K

22K

47K

100K

220K

470K

2.2M

4.7M

10M

1.91

0.90

0.41

0.19

0.09

0.04

0.02

0.01

8.1

11.9

17.3

25.7

37.5

54.8

81.2

119.9

173

257.7

300

369

252

173

116

6.3

1.36

0.63

0.30

0.13

0.06

0.03

1.5

0.9

0.41

0.19

0.09

0.04

12.2

18.2

26.6

38.7

57.4

83.9

122

181.6

265

300

122

82.6

56.6

38.7

26.1

17.9

12.2

8.25

5.64

1.36

0.63

0.30

0.13

MECHANICAL SPECIFICATIONS

Mechanical Travel 300° ± 5°

Operating Torque (Typical) 3 Ncm max. 4.25 oz.-inch max.

End Stop Torque 120 Ncm max. 10.51 lb oz.-inch max.

Tightening Torque of Mounting Nut 250 Ncm max. 22 lb-inch max.

Unit Weight 23 g to 32 g max. 0.8 oz. to 1.13 oz.

Terminals e3: Pure Sn

ENVIRONMENTAL SPECIFICATIONS

Temperature Range - 55 °C to 125 °C

Climatic Category 55/125/56

Sealing Fully sealed - Container IP67

OPTIONS

Special Feature Command Shaft

Length is measured from the mounting surface to the free end of the shaft. The screwdriver

slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to

drawings supplied by customers. We recommend that customers should not machine tool

shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided.

Panel Sealing (PE30M)

The panel sealing device consists of a ring located in a groove on the potentiometer face.

Sealing is obtained by tightening the ring against the panel when mounting the

potentiometer.

Old code: PE30P

Locating Peg (PE30LL) Location is obtained by fitting a special washer on the mounting face of the potentiometer.

Old code: LPRP

Shaft Locking (PE30LD)

The shaft locking device consists of a tapered nut tightening a slotted notched washer

against both bushing and shaft.

DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm.

DBAN is also available with all special types.

This device is normally supplied in a separate bag. Can be pre-mounted on request.

Assembling 

Method

1) 2)

6.5

14 wrench

12 wrench

PE30

www.vishay.com Vishay Sfernice

Revision: 14-Aug-13 4Document Number: 51037

For technical questions, contact:

sferpottrimmers@vishay.com

, see also Application Note:

www.vishay.com/doc?51001

and

www.vishay.com/doc?52029

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CENTER DETENT

• Stable position in mid mechanical travel

• Output ratio 50 % ± 10 %

• Rotational life: 10 000 actuations

ORDERING INFORMATION (First order only)

MARKING

• Vishay trademark

• Part number (including ohmic value and tolerance code)

• Manufacturing date code

• Marking of terminals 3, and a, b, c

PERFORMANCE

TESTS CONDITIONS TYPICAL VALUES AND DRIFTS

RT/RT (%) R1-2/R1-2 (%) OTHER

Electrical Endurance 1000 h at rated power

90'/30' - ambient temp. 70 °C ± 1 % - Contact res. variation: < 3 % Rn

Climatic Sequence

Phase A dry heat 125 °C

Phase B damp heat

Phase C cold - 55 °C

Phase D damp heat 5 cycles

± 0.5 % ± 1 % -

Damp Heat, Steady State 56 days

40 °C 93 % HR ± 0.5 % ± 1 % Insulation resistance: > 104 M

Change of Temperature 5 cycles

- 55 °C at + 125 °C ± 0.5 % - -

Mechanical Endurance 25 000 cycles ± 3 % - Contact res. variation: < 2 % Rn

Shock

50 g’s at 11 ms

3 successive shocks

in 3 directions

± 0.1 % ± 0.2 % -

Vibration

10 Hz to 55 Hz

0.75 mm or 10 g’s

during 6 h

± 0.1 % ± 0.2 % -

Full CW Full CCW

CV1M

PE30

www.vishay.com Vishay Sfernice

Revision: 14-Aug-13 5Document Number: 51037

For technical questions, contact:

sferpottrimmers@vishay.com

, see also Application Note:

www.vishay.com/doc?51001

and

www.vishay.com/doc?52029

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ORDERING INFORMATION (part number)

MODEL BUSHING OPTION SHAFT OHMIC

VALUE TOLERANCE TAPER PACKAGING SPECIAL

NUMBER

PE30 L =

M10 x 0.75

M = Panel

sealed

M10 x 0.75

0 = none

For L bushing

D = DBAN

L = LPRP

B = DBAN

and LPRP

For M bushing

E = Peg

A = Peg

and DBAN

For L bushing (= old codes:)

FG 16 mm, slotted = AC

FL 25 mm, slotted = AM

FR 50 mm, plain = AL

For M bushing

FD = 13 mm, slotted = AC

FJ = 22 mm, slotted = AM

FP = 47 mm, plain = AL

A law =

from 22 

to 10 M

L and F

laws =

from 100 

to 2.2 M

± 20 %

On request:

± 10 %

± 5 %

A = Linear

L = Clockwise

logarithmic

F = Clockwise

inverse

logarithmic

B = Box of

10 pieces

(if applicable)

Given by

Vishay

for custom

design

E105

CV1M

PART NUMBER DESCRIPTION (for information only)

PE30 LPRP AC 200K 20 % A DBAN CV1M BO e3

MODEL FEATURES OPTION SHAFT VALUE TOL. TAPER OPTION SPECIAL DETENT PACKAGING CUSTOM

SHAFT SPECIAL LEAD

(Pb)-FREE

LBFG204 A3P 0E MB

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 02-Oct-12 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical

requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements

about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular

product with the properties described in the product specification is suitable for use in a particular application. Parameters

provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All

operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please

contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by

any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the

definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council

of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that

all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free

requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference

to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21

conform to JEDEC JS709A standards.