Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 1
1. Features
Antenna for 1559 1609 MHz, GNSS for embedded applications
Solution for all global public constellations: GPS, GLONASS, Beidou and
GALILEO.
Maintains high performance on device: DFI (Designed For Integration)
Ultra flat compact design of only 0.4mm thickness.
Designed for SMD mounting
Supplied on Tape and Reel
2. Description
Sinica is intended for use with all positioning applications. The antenna has RHCP
characteristics suitable for GNSS signals. A truly novel antenna approach with ultra-
low profile, but with the high performance of a ceramic patch.
3. Applications
Trackers
Portable Devices
Drones
Network Devices
Wearable devices
Sinica GNSS Antenna
Part No. SR4G008 lamiiANT® Product Specification
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 2
4. Part Number
Sinica: SR4G008
5. General Data
6. RF Characteristics
Product name
Sinica
Part Number
SR4G008
Frequency
1559 1609 MHz
Polarization
Linear
Operating temperature
-40°C to125°C
Impedance with matching
50 Ω
Weight
< 0.2 g
Antenna type
SMD
Dimensions
7.0 x 5.8 x 0.4 (mm)
Typical performance
Conditions
Peak gain
3.0dBi
Average gain (Linear)
0dBi
Average efficiency (Linear)
>75%
Average efficiency (RHCP)
>38%
Maximum return loss
-12dB
Maximum VSWR
1.4:1
1559 - 1609 MHz frequency
range
All data measured on
Antenovas evaluation PCB
Part No. SR4G008-U1
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 3
7. RF Performance
7.1 Return Loss
7.2 VSWR
1100 1200 1300 1400 1500 1600 1700 1800 1900 2000
-35
-30
-25
-20
-15
-10
-5
0
5
[MHz]
[dB] A tyune
12
1100 1200 1300 1400 1500 1600 1700 1800 1900 2000
1
2
3
4
5
6
[MHz]
[] A tyune
12
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 4
7.3 Antenna pattern
7.3.1 1559 MHz 1609 MHz
3D pattern at 1575 MHz
Drag to rotate pattern and PCB by using Adobe Reader
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 5
8. Antenna Dimensions
All dimensions in mm
Bottom side dimensions
6 solder pads (1.0 x 1.0 mm)
L
W
H
Length
Width
Height
7.0 ±0.1
5.8 ±0.1
0.4 ±0.2
Pin 1 marker
W
L
H
Pin 1
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 6
9.0 Antenna footprint
The recommended host PCB footprint is below. This is shown as it should be placed
on the host PCB.
6 copper pads all 1.0 x 1.0 (mm)
*CAD files of the antenna footprint are available at www.antenova-m2m.com.
10.0 Schematic
The circuit for the antenna and the matching components is below. The RF feed
connection and GND connections are critical to the function of the antenna, and must be
followed as shown. This circuit can be used for the circuit capture of the host PCB.
Pi Network
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 7
11. Electrical Interface
11.1 Transmission Line
All transmission lines should be designed to have a characteristic impedance of 50Ω.
• The length of the transmission lines should be kept to a minimum
• Any other parts of the RF system like transceivers, power amplifiers, etc, should also
be designed to have an impedance of 50 Ω
Once the material for the PCB has been chosen (PCB thickness and dielectric constant),
a coplanar transmission line can easily be designed using any of the commercial
software packages for transmission line design. For the chosen PCB thickness, copper
thickness and substrate dielectric constant, the program will calculate the appropriate
transmission line width and gaps on either side of the track so the characteristic
impedance of the co-planar transmission line is 50 Ω.
11.2 Matching Circuit
The antenna requires a matching circuit that must be optimized for each product. The
matching circuit will require up to three components and the following pad layout should
be designed into the device so the correct circuit can be installed.
The Pi matching network must be placed close to the antenna feed to ensure it is
more effective in tuning the antenna.
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 8
12.0 Antenna Integration Guide
12.1 Antenna Placement
Whichever the host PCB size used, the antenna should be placed ideally on the host
PCB’s longest edge at the centre.
Where the centre is not a viable option the antenna can be placed offset on the PCB to
within the limits shown below. A minimum of 5mm from either PCB edge should be
observed. Where possible this distance should be greater than 5mm.
>5mm
>5mm
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 9
12.2 Host PCB Layout
The host PCB must ensure the footprint and clearance meets the antenna
specification. An example of the PCB layout shows the antenna footprint with
clearance.
Pins 3, 4 and 6 (GND) are shown directly connecting to the GND with the shortest
route. The feed (Pin 2) connects to the matching circuit close to the antenna.
Example host layout
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 10
12.3 Host PCB Clearance
Below shows the antenna footprint and clearance through all layers on the PCB.
Only the antenna pads and connections to feed and GND are present within this
clearance area. The clearance area required is 7.0 x 5.8 (mm).
Example host layout
The clear-out area is simply defined as the same size as the antenna. No additional
clearance is required.
7.0mm
5.8mm
Clearance area
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 11
13.0 Host PCB Size
The minimum recommended host PCB size to be used is 40 x 20 (mm). Below is the
antenna performance vs PCB length.
Passive Efficiency vs. PCB length
All results measured in Antenova’s anechoic chamber
40mm
60mm
80mm
60mm
80mm
40mm
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 12
14.0 Reference Board
The reference board has been designed for evaluation purposes of SR4G008 includes a SMA
female connector.
SR4G008 Evaluation Board
To order a reference board contact sales@antenova-m2m.com.
Please state if single or two antenna EVB is required.
80mm
35mm
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 13
15. Soldering
This antenna is suitable for lead free soldering.
The reflow profile should be adjusted to suit the device, oven and solder paste, while
observing the following conditions:
The maximum temperature should not exceed 240 ºC
However for lead free soldering, a maximum temperature of 255 ºC for no more
than 20 seconds is permitted.
The antenna should not be exposed to temperatures exceeding 120 ºC more
than 3 times during the soldering process.
16. Hazardous Material Regulation Conformance
The antenna has been tested to conform to RoHS requirements. A certificate of
conformance is available from Antenova M2M’s website.
17. Packaging
17.1 Optimal Storage Conditions
Temperature
-10ºC to 40ºC
Humidity
Less than 75% RH
Shelf life
18 Months
Storage place
Away from corrosive gas and direct sunlight
Packaging
Reels should be stored in unopened sealed
manufacturer’s plastic packaging.
Note: Storage of open reels of antennas is not recommended due to possible oxidization
of pads on antennas. If short term storage is necessary, then it is highly recommended
that the bag containing the antenna reel is re-sealed and stored in like storage conditions
as in above table.
The shelf life of the antenna is 2 years, providing the factory seal on the package has not
been broken
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 14
17.2 Tape Characteristics
Do
Ao
Bo
P0
P1
P2
1.55 +0.1
6.10 ± 0.1
7.30 ± 0.1
4.00 ± 0.1
12.00 ± 0.1
2.00 ± 0.1
E
F
W
K0
1.75 ± 0.1
7.50 ± 0.1
16.00 ± 0.3
0.95 ± 0.1
Dimensions in mm
Notes:
a) Sprocket hole pitch cumulative tolerance = ±0.2
b) Chamber not to exceed 1mm in 100mm
c) Ao and Bo measured on a plane 0.1mm above the bottom of the pocket.
d) K0 measured from a plane on the inside bottom of the pocket to the top surface of the
carrier.
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 15
17.3 Reel Dimensions
A
C
N
W1
178.0 ± 2.0
13.2 ± 0.5
60.0
14.0
All dimensions in mm
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Antennas for Wireless M2M Applications
Product Specification Page 16
17.4 Box Dimensions
Width
(W)
Breadth
(B)
Thickness
(H)
203mm
188mm
40mm
17.5 Bag Properties
Reels are supplied in protective plastic packaging.
17.6 Reel Label Information
60.00 mm
90.00mm
Antenova Limited
Antenova Asia Ltd
4F, No 324, Sec 1 Nei-Hu Road
Nei-Hu District, Taipei 11493, Taiwan ROC
info@antenova.com / www.antenova-m2m.com
Description: Sinica
Part number: SR4G008
Quantity: 1,000 pieces
Date Code:
Manufacturer’s code number:
lamiiANT®
Sinica
Part No. SR4G008
Antennas for Wireless M2M Applications
Product Specification revised November 2015
Page 17
DS- SR4G008-1.1
www.antenova-m2m.com
Corporate Headquarters
Antenova Limited
2nd Floor Titan Court
Bishop Square
Hatfield
AL10 9NA
UK
Tel: +44 1233 810600
Email: sales@antenova-m2m.com
North America Headquarters
Antenova Limited
100 Brush Creek Road, Suite 103
Santa Rosa
California, 95404
USA
Tel: +1 707 890 5202
Email: sales@antenova-m2m.com
Asia Headquarters
Antenova Asia Limited
4F, No. 324, Sec. 1, Hei-Hu Road
Hei-Hu District
Taipei 11493
Taiwan, ROC
Tel: +886 (0) 2 8797 8630
Fax: +886 (0) 2 8797 6890
Email: sales@antenova-m2m.com
Copyright® Antenova Ltd. All Rights Reserved. Antenova ®, Antenova M2M ®, gigaNOVA ®, the Antenova
product family names, and the Antenova and Antenova M2M logos are trademarks and/or registered trademarks
of Antenova Ltd. Any other names and/or trademarks belong to their respective companies.
The materials provided herein are believed to be reliable and correct at the time of printing. Antenova does not
warrant the accuracy or completeness of the information, text, graphics or other items contained within this
information. Antenova further assumes no responsibility for the use of this information, and all such information
shall be entirely at the user’s risk.
Release date July 2015