Order this document by MJD44H11/D SEMICONDUCTOR TECHNICAL DATA DPAK For Surface Mount Applications *Motorola Preferred Device . . . for general purpose power and switching such as output or driver stages in applications such as switching regulators, converters, and power amplifiers. * * * * * * * Lead Formed for Surface Mount Application in Plastic Sleeves (No Suffix) Straight Lead Version in Plastic Sleeves ("-1" Suffix) Lead Formed Version in 16 mm Tape and Reel for Surface Mount ("T4" Suffix) Electrically Similar to Popular D44H/D45H Series Low Collector Emitter Saturation Voltage -- VCE(sat) = 1.0 Volt Max @ 8.0 Amperes Fast Switching Speeds Complementary Pairs Simplifies Designs IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII SILICON POWER TRANSISTORS 8 AMPERES 80 VOLTS 20 WATTS MAXIMUM RATINGS D44H11 or D45H11 Unit VCEO 80 Vdc VEB 5 Vdc Collector Current -- Continuous Peak IC 8 16 Adc Total Power Dissipation @ TC = 25_C Derate above 25_C PD 20 0.16 Watts W/_C Total Power Dissipation (1) @ TA = 25_C Derate above 25_C PD 1.75 0.014 Watts W/_C TJ, Tstg - 55 to 150 _C Collector-Emitter Voltage Emitter-Base Voltage Operating and Storage Junction Temperature Range THERMAL CHARACTERISTICS Symbol Max Unit Thermal Resistance, Junction to Case Characteristic RJC 6.25 _C/W Thermal Resistance, Junction to Ambient (1) RJA 71.4 _C/W TL 260 _C Lead Temperature for Soldering CASE 369A-13 CASE 369-07 MINIMUM PAD SIZES RECOMMENDED FOR SURFACE MOUNTED APPLICATIONS 0.165 4.191 Symbol 0.190 4.826 Rating 0.243 6.172 0.063 1.6 0.118 3.0 0.07 1.8 (1) These ratings are applicable when surface mounted on the minimum pad size recommended. inches mm Preferred devices are Motorola recommended choices for future use and best overall value. REV 2 Motorola, Inc. 1995 Motorola Bipolar Power Transistor Device Data 1 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ELECTRICAL CHARACTERISTICS (TC = 25_C unless otherwise noted) Characteristic Symbol Min Typ Max Unit VCEO(sus) 80 -- -- Vdc Collector Cutoff Current (VCE = Rated VCEO, VBE = 0) ICES -- -- 10 A Emitter Cutoff Current (VEB = 5 Vdc) IEBO -- -- 50 A Collector-Emitter Saturation Voltage (IC = 8 Adc, IB = 0.4 Adc) VCE(sat) -- -- 1 Vdc Base-Emitter Saturation Voltage (IC = 8 Adc, IB = 0.8 Adc) VBE(sat) -- -- 1.5 Vdc hFE 60 -- -- -- 40 -- -- -- -- 130 230 -- -- -- -- 50 40 -- -- -- -- 300 135 -- -- -- -- 500 500 -- -- -- -- 140 100 -- -- OFF CHARACTERISTICS Collector-Emitter Sustaining Voltage (IC = 30 mA, IB = 0) ON CHARACTERISTICS DC Current Gain (VCE = 1 Vdc, IC = 2 Adc) DC Current Gain (VCE = 1 Vdc, IC = 4 Adc) DYNAMIC CHARACTERISTICS Collector Capacitance (VCB = 10 Vdc, ftest = 1 MHz) Gain Bandwidth Product (IC = 0.5 Adc, VCE = 10 Vdc, f = 20 MHz) Ccb MJD44H11 MJD45H11 pF fT MJD44H11 MJD45H11 MHz SWITCHING TIMES Delay and Rise Times (IC = 5 Adc, IB1 = 0.5 Adc) Storage Time (IC = 5 Adc, IB1 = IB2 = 0.5 Adc) Fall Time (IC = 5 Adc, IB1 = IB2 = 0.5 Adc) 2 td + tr MJD44H11 MJD45H11 ns ts MJD44H11 MJD45H11 ns tf MJD44H11 MJD45H11 ns Motorola Bipolar Power Transistor Device Data r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1 0.7 0.5 D = 0.5 0.3 0.2 0.2 RJC(t) = r(t) RJC RJC = 6.25C/W MAX D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) - TC = P(pk) JC(t) 0.1 0.1 0.07 0.05 0.05 0.02 0.01 0.03 0.02 P(pk) t1 SINGLE PULSE 0.01 0.01 0.02 0.03 0.05 0.1 0.2 0.3 0.5 1 2 3 5 t, TIME (ms) 10 20 30 t2 DUTY CYCLE, D = t1/t2 50 100 200 300 500 1k Figure 1. Thermal Response IC, COLLECTOR CURRENT (AMP) 20 10 500 s 5 3 2 dc 100 s There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown. Safe operating area curves indicate IC - VCE limits of the transistor that must be observed for reliable operation; i.e., the transistor must not be subjected to greater dissipation than the curves indicate. The data of Figure 2 is based on T J(pk) = 150_C; TC is variable depending on conditions. Second breakdown pulse limits are valid for duty cycles to 10% provided T J(pk) 150_C. T J(pk) may be calculated from the data in Figure 1. At high case temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by second breakdown. 1 ms 5 ms 1 THERMAL LIMIT @ TC = 25C WIRE BOND LIMIT 0.5 0.3 v 0.1 0.05 0.02 1 50 5 7 10 20 30 3 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 70 100 Figure 2. Maximum Forward Bias Safe Operating Area PD, POWER DISSIPATION (WATTS) TA TC 2.5 25 2 20 TC 1.5 15 TA SURFACE MOUNT 1 10 0.5 5 0 0 25 50 75 100 125 150 T, TEMPERATURE (C) Figure 3. Power Derating Motorola Bipolar Power Transistor Device Data 3 1000 hFE, DC CURRENT GAIN hFE, DC CURRENT GAIN 1000 VCE = 4 V 100 VCE = 1 V TJ = 25C 10 0.1 1 VCE = 4 V 100 1V TJ = 25C 10 0.1 10 1 10 IC, COLLECTOR CURRENT (AMPS) IC, COLLECTOR CURRENT (AMPS) Figure 4. MJD44H11 DC Current Gain Figure 5. MJD45H11 DC Current Gain 1000 1000 hFE , DC CURRENT GAIN hFE , DC CURRENT GAIN TJ = 125C TJ = 125C 25C 100 - 40C VCE = 1 V 10 0.1 1 10 Figure 7. MJD45H11 Current Gain versus Temperature 1.2 SATURATION VOLTAGE (VOLTS) SATURATION VOLTAGE (VOLTS) 1 Figure 6. MJD44H11 Current Gain versus Temperature VBE(sat) 0.6 IC/IB = 10 TJ = 25C VCE(sat) 1 IC, COLLECTOR CURRENT (AMPS) Figure 8. MJD44H11 On-Voltages 4 0.1 IC, COLLECTOR CURRENT (AMPS) 0.8 0 0.1 VCE = 1 V IC, COLLECTOR CURRENT (AMPS) 1 0.2 100 10 10 1.2 0.4 25C - 40C 10 1 VBE(sat) 0.8 0.6 0.4 IC/IB = 10 TJ = 25C VCE(sat) 0.2 0 0.1 1 IC, COLLECTOR CURRENT (AMPS) Figure 9. MJD45H11 On-Voltages Motorola Bipolar Power Transistor Device Data 10 PACKAGE DIMENSIONS C B V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. SEATING PLANE -T- E R 4 Z A S 1 2 DIM A B C D E F G H J K L R S U V Z 3 U K F J L H D G 2 PL 0.13 (0.005) M T INCHES MIN MAX 0.235 0.250 0.250 0.265 0.086 0.094 0.027 0.035 0.033 0.040 0.037 0.047 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.090 BSC 0.175 0.215 0.020 0.050 0.020 --- 0.030 0.050 0.138 --- STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 5.97 6.35 6.35 6.73 2.19 2.38 0.69 0.88 0.84 1.01 0.94 1.19 4.58 BSC 0.87 1.01 0.46 0.58 2.60 2.89 2.29 BSC 4.45 5.46 0.51 1.27 0.51 --- 0.77 1.27 3.51 --- BASE COLLECTOR EMITTER COLLECTOR CASE 369A-13 ISSUE W C B V E R 4 A 1 2 3 S -T- K SEATING PLANE J F H D G 3 PL 0.13 (0.005) M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G H J K R S V INCHES MIN MAX 0.235 0.250 0.250 0.265 0.086 0.094 0.027 0.035 0.033 0.040 0.037 0.047 0.090 BSC 0.034 0.040 0.018 0.023 0.350 0.380 0.175 0.215 0.050 0.090 0.030 0.050 STYLE 1: PIN 1. 2. 3. 4. T MILLIMETERS MIN MAX 5.97 6.35 6.35 6.73 2.19 2.38 0.69 0.88 0.84 1.01 0.94 1.19 2.29 BSC 0.87 1.01 0.46 0.58 8.89 9.65 4.45 5.46 1.27 2.28 0.77 1.27 BASE COLLECTOR EMITTER COLLECTOR CASE 369-07 ISSUE K Motorola Bipolar Power Transistor Device Data 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 Motorola Bipolar Power Transistor Device Data *MJD44H11/D* MJD44H11/D