TQP9224 High Linearity 0.25 W Small Cell PA (R) General Description The TQP9224 is a high-linearity three-stage power amplifier in a low-cost surface-mount package with on-chip bias control and temperature control circuits, suitable for small cell or enterprise Femto cell base station applications. The TQP9224 provides 36.7 dB high gain and -50 dBc ACLR at +24dBm linear power using a 20 MHz LTE signal over the 2.3-2.4GHz frequency range covering 3GPP Bands 30, 40. The TQP9224 integrates three high performance amplifier stages to allow for a compact system design and requires very few external components for operation. The amplifier is bias adjustable allowing the amplifier's power consumption to be optimized for specific performance requirements. The TQP9224 is available in a leadfree/RoHS-compliant 7x7mm surface mount package. 14 Pin 7x7mm Leadless SMT Package Product Features * * * * * * * * * 2.3-2.4GHz Frequency Range Fully integrated, 3-Stage Power Amplifier Internally Matched 50 Input/Output -50dBc ACLR at Pavg = +24dBm 36.7dB Gain 14% PAE at +24dBm 204mA Quiescent Current On-chip Control Bias and Temp. Comp Circuit RoHS compliant * Covers Band 30, 40 Functional Block Diagram Applications * * * * * * Top View Data Sheet March 1, 2018 | Subject to change without notice Small Cell/Picocell Enterprise Femtocell Customer Premises Equipment (CPE) Data Cards and Terminals Distributed Antenna Systems (DAS) Booster Amps, Repeaters Ordering Information Part No. Description TQP9224TR13 2,500 pieces on a 13" reel (standard) TQP9224PCB401 2.3-2.4GHz Evaluation Board - 1 of 8 - www.qorvo.com TQP9224 High Linearity 0.25 W Small Cell PA (R) Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating -55 to +150C Storage Temperature RF Input Power, CW, 50, T=+25C Supply Voltage (VCC) +9 dBm 6V VREF Parameter Min Typ Max Units VCC1, Vcc2 +3.6 +4.5 +5.25 V Vref +2.75 +2.85 +2.95 V +85 C +156 C -40 TCASE +3.5 V Tj at TCASE max Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Electrical Specifications Parameter Conditions(1) Min Frequency Range Typ 2300 Test Frequency Max Units 2400 MHz MHz 2350 Gain 34 36.7 40 dB Input Return Loss 16 dB Output Return Loss 8 dB +33.6 dBm Output P1dB ACLR POUT = +24 dBm, 20MHz LTE E-TM1.1, 9.5 dB PAR Power Added Efficiency POUT = +24 dBm, 20MHz LTE E-TM1.1, 9.5 dB PAR Spurious Output Level POUT = +24 dBm, 10:1 VSWR VSWR survivability No permanent degradation or failure 10:1 Quiescent Current, ICQ VCC1 + VCC2 160 Reference Current , Iref Temp = -40C to +85C, VREF = +2.85V 8.7 Leakage Current VCC = +4.5 V, VREF = 0 V 1.5 8 A Operational Current, ICC POUT = +24dBm 390 430 mA 0% Vref to 90% RF Rise time 1.7 2.5 s 100% Vref to 10% RF Fall time 0.87 1 s 2F0 at +24dBm, CW signal -40 -35 dBc 3F0 at +24dBm, CW signal -54 -49 dBc 4F0 at +24dBm, CW signal -61 -56 dBc 35.4 C/W Switching Speed Harmonics Thermal Resistance, jc -50 13 Module (junction to case) -45 dBc 14 % <60 dBc - 204 250 mA mA Notes: 1. Test conditions unless otherwise noted: VCC1=Vcc2 = +4.5V, VREF = +2.85V, Temp=+25C, 50 system. Data Sheet March 1, 2018 | Subject to change without notice - 2 of 8 - www.qorvo.com TQP9224 High Linearity 0.25 W Small Cell PA (R) Evaluation Board (TQP9224-PCB) J5 Vpd R1 0 C1 0.01uF C11 J3 100pF Vcc1 1 14 C5 Biasing Circuit 2 13 10uF (6032) C9 J2 3 Match 12 RF Output 1.0uF C6 4 11 C10 10 1000pF 1000pF J1 5 Match RF Input C3 6 9 7 8 1.0uF C14 10uF (6032) R2 DNP C12 J4 Vcc2 DNP C13 J6 DNP Vdet Bill of Material - TQP9224-PCB Reference Des. n/a U1 R1 C1 C11 C3, C9 C5, C14 C6, C10 Value Description n/a Printed Circuit Board n/a High Linearity 0.25 W Power Amplifier 0 Resistor, Chip, 0603, 5% 0.01 uF Capacitor, Chip, 0603, 5% 100 pF Capacitor, Chip, 0603, 5% 0.1 uF Capacitor, Chip, 0603, 5% 10 uF Capacitor , Chip, 6032, 10%, Tantalum 1000 pF Capacitor , Chip, 0603, NPO/COG, 5% Data Sheet March 1, 2018 | Subject to change without notice - 3 of 8 - Manuf. Qorvo various various various various various various Part Number TQP9224 www.qorvo.com TQP9224 High Linearity 0.25 W Small Cell PA (R) Performance Plots Test conditions unless otherwise noted: VCC1 = VCC2 = +4.5V, VREF = +2.85V, ICQ = 204mA, IREF = 8.7mA, Temp.=+25C Gain vs Frequency vs Temperature 42 Input Return Loss vs. Frequency 0 Output Return Loss vs. Frequency 0 Temp.=+25C Temp.=+25C 40 -5 36 |S22| (dB) |S11| (dB) Gain (dB) -5 38 -10 -10 +85C -15 +25C 34 -40C 32 2300 2320 2340 2360 2380 -20 2300 2400 2320 2340 Frequncy (MHz) -35 ACLR (dBc) ACLR (dBc) 2.35GHz_L 2.35GHz_U 2.40GHz_L 2.40GHz_U -50 -55 -60 18 2400 2380 2400 34 -40 -40C_U +25C_L +25C_U -45 +85C_L +85C_U -50 19 20 21 22 23 24 25 26 16 17 18 19 Pout (dBm) +85C +25C 32 -40C 20 21 22 23 24 25 30 2300 26 2320 2340 Pout (dBm) Efficiency vs Pout vs Frequency 20 2360 Frequency (MHz) Efficiency vs Pout vs Temperature 20 LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz PAR 9.5 dB no clipping LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz PAR 9.5 dB no clipping 15 15 2.30GHz -40C 2.35GHz 10 PAE (%) PAE (%) 33 31 -60 17 2380 P1dB vs Frequency 35 -55 16 2360 -40C_L 2.30GHz_U -45 2340 Freq = 2350MHz LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz PAR 9.5 dB no clipping 2.30GHz_L -40 2320 Frequency (MHz) P1dB (dBm) -35 -15 2300 2400 ACLR vs Pout vs Temperature -30 Temp.=+25C LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz PAR 9.5 dB no clipping 2380 Frequency (MHz) ACLR vs Pout vs Frequency -30 2360 2.40GHz 5 +25C 10 +85C 5 Temp.=+25C Freq = 2350MHz 0 0 16 17 18 19 20 21 22 23 24 25 26 Pout (dBm) Data Sheet March 1, 2018 | Subject to change without notice 16 17 18 19 20 21 22 23 24 25 26 Pout (dBm) - 4 of 8 - www.qorvo.com TQP9224 High Linearity 0.25 W Small Cell PA (R) Pin Configuration and Description Top View Pad No. 1 2, 3, 6, 8, 9, 10, 13, 14 4 Label VREF Description Sets the bias current for the amplifiers. It can also be used to power down the device. GND RF and DC ground. VCC1 Voltage supply for the active bias circuitry. 5 RFin RF input pin. The DC is internally blocked at this pin. 7 NC No internal connection. 11 VCC2 DC voltage supply connection for AMP1, 2, 3. 12 RFout RF output pin. The DC is internally blocked at this pin. Backside Paddle RF/DC GND RF/DC ground. See PCB Mounting Pattern for suggested footprint. Evaluation Board PCB Information Qorvo PCB 1126637 Material and Stack-up 1 oz. Cu top layer 0.014" Nelco N-4000-13 1 oz. Cu inner layer 0.062" 0.006" Finished Board Thickness Core 1 oz. Cu inner layer 0.014" Nelco N-4000-13 1 oz. Cu bottom layer 50 ohm line dimensions: width = .028" spacing = .028". Data Sheet March 1, 2018 | Subject to change without notice - 5 of 8 - www.qorvo.com TQP9224 High Linearity 0.25 W Small Cell PA (R) Package Marking and Dimensions Marking: Part Number - TQP9224 Trace Code TQP9224 A S PIN 1 Location A A 14 A A 13 A A 12 A S A A S11 A A 10 A A 9 A A 8 Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Dimension and tolerance formats conform to ASME Y14.4M-1994. 3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012. BOTTOM VIEW BOTTOM PINS VIEW A A A T A Reac 07.00mm X 0 A A D000000 Data Sheet March 1, 2018 | Subject to change without notice - 6 of 8 - A A S D000000 www.qorvo.com 00:00 A A A3 TQP9224 High Linearity 0.25 W Small Cell PA (R) PCB Mounting Pattern A S A PIN 1 Location S PIN 1 Location A A A A A A A A A A A A A A A A A A A A A A A A A A A S S A 0.175 RECOMMENDED LAND PATTERN RECOMMENDED LAND PATTERN MASK Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Use 1 oz. copper minimum for top and bottom layer metal. 3. Vias are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. We recommend a 0.35mm Reach Further - Reach faster (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10"). 07.00mm X 07.00mm, 4 LAYER 4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance. TriQuint D000000 Data Sheet March 1, 2018 | Subject to change without notice - 7 of 8 - D000000 00:00 A3H RLP RLPmsk www.qorvo.com TQP9224 High Linearity 0.25 W Small Cell PA (R) Handling Precautions Parameter Rating Standard ESD-Human Body Model (HBM) Class 2 ESDA/JEDEC JS-001-2012 ESD-Charged Device Model (CDM) Class C3 JEDEC JESD22-C101F MSL-Moisture Sensitivity Level Level 3 IPC/JEDEC J-STD-020 Caution! ESD-Sensitive Device Solderability Compatible with both lead-free (260C max. reflow temp.) and tin/lead (245C max. reflow temp.) soldering processes. Solder profiles available upon request. Contact plating: Electrolytic plated Au over Ni RoHS Compliance This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: * Product uses RoHS Exemption 7c-I to meet RoHS Compliance requirements * Halogen Free (Chlorine, Bromine) * * * * Antimony Free TBBP-A (C15H12Br402) Free PFOS Free SVHC Free Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations: Tel: 1-844-890-8163 Web: www.qorvo.com Email: customer.support@qorvo.com For technical questions and application information: Email: appsupport@qorvo.com Important Notice The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Copyright 2018 (c) Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc. Data Sheet March 1, 2018 | Subject to change without notice - 8 of 8 - www.qorvo.com