34
04.16
D
Capacitance range:
33 pF to 0.033 mF (E12-values on request)
Rated voltages:
63 VDC, 100 VDC, 250 VDC, 400 VDC,
630 VDC, 800 VDC, 1000 VDC
Capacitance tolerances:
±20%, ±10%, ±5%, ±2.5% (±2%, ±1.5%
or ±1% available as precision capacitors
subject to special enquiry)
Operating temperature range:
–55+ C to +100+ C
Test specifications:
In accordance with IEC 60384-13
Climatic test category:
55/100/56 in accordance with IEC
Insulation resistance at +20+ C:
5 x 105 M¸
(mean value: 1 x 106 M¸)
Measuring voltage:
Ur = 63 V: Utest = 50 V/1 min.
Ur 100 V: Utest = 100 V/1 min.
Dissipation factors at +20) C: tan d
at f C 1000 pF 1000 pF < C 4700 pF C > 4700 pF
1 kHz 3 x 10-4 4 x 10-4 4 x 10-4
10 kHz 3 x 10-4 4 x 10-4 4 x 10-4
100 kHz 4 x 10-4 5 x 10-4
1 MHz 10 x 10-4 – –
WIMA FKP 2
Polypropylene (PP) Film/Foil Capacitors for Pulse Applications in PCM 5 mm.
Capacitances from 33 pF to 0.033 mF. Rated Voltages from 63 VDC to 1000 VDC.
Special Features Electrical Data
˜ Pulse duty construction
˜ Close tolerances up to ±2.5 %
(±1 % on request)
˜ Very low dissipation factor
˜ Negative capacitance change
versus temperature
˜ Very low dielectric absorption
˜ According to RoHS 2011/65/EU
Typical Applications
For high frequency applications e.g.
˜ Sample and hold
˜ Timing
˜ LC-Filtering
˜ Oscillating circuits
˜ Audio equipment
Construction
Dielectric:
Polypropylene (PP) film
Capacitor electrodes:
Metal foil
Internal construction:
Plastic film
Metal foil electrode
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations:
Tinned wire.
Marking:
Colour: Red. Marking: Black.
Epoxy resin seal: Yellow
Test voltage: 2 Ur, 2 sec.
Maximum pulse rise time:
1000 V/msec for pulses equal to the
rated voltage
Dielectric absorption:
0.05%
Temperature coefficient:
–200 x 10-6/+ C (typical)
Voltage derating:
A voltage derating factor of 1.35 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages
Reliability:
Operational life 300 000 hours
Failure rate 5 fit (0.5 x Ur and 40+ C)
Mechanical Tests
Pull test on pins:
10 N in direction of pins according to
IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test:
4000 bumps at 390 m/sec2 in
accordance with IEC 60068-2-29
Packing
Available taped and reeled.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
35
04.16
Continuation
General Data
WIMA FKP 4
D
Capacitance 63 VDC/40 VAC* 100 VDC/63 VAC*
W H L PCM** Part number W H L PCM** Part number
100 pF 4.5 6 7.2 5 FKP2C001001D00_ _ _ _ 4.5 6 7.2 5 FKP2D001001D00_ _ _ _
150 „ 4.5 6 7.2 5 FKP2C001501D00_ _ _ _ 4.5 6 7.2 5 FKP2D001501D00_ _ _ _
220 „ 4.5 6 7.2 5 FKP2C002201D00_ _ _ _ 4.5 6 7.2 5 FKP2D002201D00_ _ _ _
330 „ 4.5 6 7.2 5 FKP2C003301D00_ _ _ _ 4.5 6 7.2 5 FKP2D003301D00_ _ _ _
470 „ 4.5 6 7.2 5 FKP2C004701D00_ _ _ _ 4.5 6 7.2 5 FKP2D004701D00_ _ _ _
680 „ 4.5 6 7.2 5 FKP2C006801D00_ _ _ _ 4.5 6 7.2 5 FKP2D006801D00_ _ _ _
1000 pF 4.5 6 7.2 5 FKP2C011001D00_ _ _ _ 4.5 6 7.2 5 FKP2D011001D00_ _ _ _
1500 „ 4.5 6 7.2 5 FKP2C011501D00_ _ _ _ 4.5 6 7.2 5 FKP2D011501D00_ _ _ _
2200 4.5 6 7.2 5 FKP2C012201D00_ _ _ _ 4.5 6 7.2 5 FKP2D012201D00_ _ _ _
3300 4.5 6 7.2 5 FKP2C013301D00_ _ _ _ 5.5 7 7.2 5 FKP2D013301G00_ _ _ _
4700 4.5 6 7.2 5 FKP2C014701D00_ _ _ _ 5.5 7 7.2 5 FKP2D014701G00_ _ _ _
6800 4.5 6 7.2 5 FKP2C016801D00_ _ _ _ 5.5 7 7.2 5 FKP2D016801G00_ _ _ _
0.01 mF 5.5 7 7.2 5 FKP2C021001G00_ _ _ _ 6.5 8 7.2 5 FKP2D021001I00_ _ _ _
0.015 6.5 8 7.2 5 FKP2C021501I00_ _ _ _ 7.2 8.5 7.2 5 FKP2D021501J00_ _ _ _
0.022 „ 7.2 8.5 7.2 5 FKP2C022201J00_ _ _ _ 8.5 10 7.2 5 FKP2D022201L00_ _ _ _
0.033 8.5 10 7.2 5 FKP2C023301L00_ _ _ _
Capacitance 250 VDC/160 VAC* 400 VDC/220 VAC*
W H L PCM** Part number W H L PCM** Part number
100 pF 4.5 6 7.2 5 FKP2F001001D00_ _ _ _ 4.5 6 7.2 5 FKP2G001001D00_ _ _ _
150 4.5 6 7.2 5 FKP2F001501D00_ _ _ _ 4.5 6 7.2 5 FKP2G001501D00_ _ _ _
220 4.5 6 7.2 5 FKP2F002201D00_ _ _ _ 4.5 6 7.2 5 FKP2G002201D00_ _ _ _
330 4.5 6 7.2 5 FKP2F003301D00_ _ _ _ 4.5 6 7.2 5 FKP2G003301D00_ _ _ _
470 4.5 6 7.2 5 FKP2F004701D00_ _ _ _ 4.5 6 7.2 5 FKP2G004701D00_ _ _ _
680 4.5 6 7.2 5 FKP2F006801D00_ _ _ _ 4.5 6 7.2 5 FKP2G006801D00_ _ _ _
1000 pF 4.5 6 7.2 5 FKP2F011001D00_ _ _ _ 4.5 6 7.2 5 FKP2G011001D00_ _ _ _
1500 4.5 6 7.2 5 FKP2F011501D00_ _ _ _ 4.5 6 7.2 5 FKP2G011501D00_ _ _ _
2200 4.5 6 7.2 5 FKP2F012201D00_ _ _ _ 4.5 6 7.2 5 FKP2G012201D00_ _ _ _
3300 5.5 7 7.2 5 FKP2F013301G00_ _ _ _ 5.5 7 7.2 5 FKP2G013301G00_ _ _ _
4700 6.5 8 7.2 5 FKP2F014701I00_ _ _ _ 6.5 8 7.2 5 FKP2G014701I00_ _ _ _
6800 6.5 8 7.2 5 FKP2F016801I00_ _ _ _ 7.2 8.5 7.2 5 FKP2G016801J00_ _ _ _
0.01 mF 7.2 8.5 7.2 5 FKP2F021001J00_ _ _ _ 8.5 10 7.2 5 FKP2G021001L00_ _ _ _
0.015 8.5 10 7.2 5 FKP2F021501L00_ _ _ _
* AC voltage: f 1000 Hz; 1.4 x Urms + UDC Ur
** PCM = Printed circuit module = pin spacing.
E12 values and individual values available
from 27 pF up on request.
Dims. in mm.
d = 0.5 l
Rights reserved to amend design data without prior notification.
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
2.5 % = H
2 % = G
1.5 % = F
1 % = E
Packing: bulk = S
Pin length: 6-2 = SD
Taped version see page 145.
5
PCM
at the pin exit points
(0.5)±
L
W
H
d
6
-2
110 100
1000
f/MHz
357357
7
5
3
7
5
3
10
1
0.1
0.01
Z
-- 33 pF
-- 47 pF
-- 100 pF
-- 220 pF
-- 470 pF
-- 1000 pF
-- 2200 pF
-- 4700 pF
-- 0.01 µF
-- 0.022 µF
-- 0.033 µF
Impedance change with frequency
(general guide).
Continuation page 36
WIMA FKP 2
36
04.16
WIMA FKP 4
Continuation
General Data
D
Capacitance 630 VDC/250 VAC* 800 VDC/250 VAC*
W H L PCM** Part number W H L PCM** Part number
100 pF 4.5 6 7.2 5 FKP2J001001D00_ _ _ _ 4.5 6 7.2 5 FKP2L001001D00_ _ _ _
150 4.5 6 7.2 5 FKP2J001501D00_ _ _ _ 4.5 6 7.2 5 FKP2L001501D00_ _ _ _
220 4.5 6 7.2 5 FKP2J002201D00_ _ _ _ 4.5 6 7.2 5 FKP2L002201D00_ _ _ _
330 4.5 6 7.2 5 FKP2J003301D00_ _ _ _ 4.5 6 7.2 5 FKP2L003301D00_ _ _ _
470 4.5 6 7.2 5 FKP2J004701D00_ _ _ _ 5.5 7 7.2 5 FKP2L004701G00_ _ _ _
680 4.5 6 7.2 5 FKP2J006801D00_ _ _ _ 5.5 7 7.2 5 FKP2L006801G00_ _ _ _
1000 pF 4.5 6 7.2 5 FKP2J011001D00_ _ _ _ 5.5 7 7.2 5 FKP2L011001G00_ _ _ _
1500 4.5 6 7.2 5 FKP2J011501D00_ _ _ _ 5.5 7 7.2 5 FKP2L011501G00_ _ _ _
2200 5.5 7 7.2 5 FKP2J012201G00_ _ _ _ 6.5 8 7.2 5 FKP2L012201I00_ _ _ _
3300 6.5 8 7.2 5 FKP2J013301I00_ _ _ _ 7.2 8.5 7.2 5 FKP2L013301J00_ _ _ _
4700 6.5 8 7.2 5 FKP2J014701I00_ _ _ _ 8.5 10 7.2 5 FKP2L014701L00_ _ _ _
6800 „ 7.2 8.5 7.2 5 FKP2J016801J00_ _ _ _
0.01 mF 8.5 10 7.2 5 FKP2J021001L00_ _ _ _
Capacitance 1000 VDC/250 VAC*
W H L PCM** Part number
33 pF 4.5 6 7.2 5 FKP2O100331D00_ _ _ _
47 „ 4.5 6 7.2 5 FKP2O100471D00_ _ _ _
68 „ 4.5 6 7.2 5 FKP2O100681D00_ _ _ _
100 pF 4.5 6 7.2 5 FKP2O101001D00_ _ _ _
150 4.5 6 7.2 5 FKP2O101501D00_ _ _ _
220 4.5 6 7.2 5 FKP2O102201D00_ _ _ _
330 4.5 6 7.2 5 FKP2O103301D00_ _ _ _
470 5.5 7 7.2 5 FKP2O104701G00_ _ _ _
680 5.5 7 7.2 5 FKP2O106801G00_ _ _ _
1000 pF 6.5 8 7.2 5 FKP2O111001I00_ _ _ _
1500 „ 7.2 8.5 7.2 5 FKP2O111501J00_ _ _ _
2200 8.5 10 7.2 5 FKP2O112201L00_ _ _ _
* AC voltage: f 1000 Hz; 1.4 x Urms + UDC Ur
** PCM = Printed circuit module = pin spacing.
Rights reserved to amend design data without prior notification.
Permissible AC voltage
in relation to frequency
at 10) C internal temperature rise
(general guide).
WIMA FKP 2
630 VDC
800 VDC
1000 VDC
f
Hz
10 2510 2510
25
10
4
567
5
2
10
5
2
10
250
2
1
U
V
rms
470 pF
220 pF
2200 pF
4700 pF
1000 pF
0.01 µF
100 pF
33 pF
47 pF
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
2.5 % = H
2 % = G
1.5 % = F
1 % = E
Packing: bulk = S
Pin length: 6-2 = SD
Taped version see page 145.
E12 values and individual values available
from 27 pF up on request.
Dims. in mm.
04.16
15
D
Recommendation for Processing
and Application of
Through-Hole Capacitors
WIMA Quality and Environmental Philosophy
ISO 9001:2008 Certification
ISO 9001:2008 is an international basic
standard of quality assurance systems
for all branches of industry. The approval
according to ISO 9001:2008 of our facto-
ries by the infaz (Institut für Auditierung und
Zertifizierung) certifies that organisation,
equipment and monitoring of quality assu-
rance in our factories correspond to inter-
nationally recognized standards.
WIMA WPCS
The WIMA Process Control System (WPCS)
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA
production. Points of application during
production process:
incoming material inspection
metallization
film inspection
schoopage
pre-healing
pin attachment
cast resin preparation/
encapsulation
100% final inspection
Testing as per customer requirements
WIMA Environmental Policy
All WIMA capacitors, irrespective of
whether through-hole devices or SMD,
are made of environmentally friendly
materials. Neither during manufacture
nor in the product itself any toxic sub-
stances are used, e.g.
– Lead – PBB/PBDE
– PCB – Arsenic
– CFC – Cadmium
– Hydrocarbon chloride – Mercury
– Chromium 6+ – etc.
We merely use pure, recyclable materials
for packing our components, such as:
carton
cardboard
adhesive tape made of paper
polystyrene
We almost completely refrain from using
packing materials such as:
foamed polystyrene (Styropor®)
adhesive tapes made of plastic
metal clips
RoHS Compliance
According to the RoHS Directive 2011/65/EU
certain hazardous substances like e.g. lead,
cadmium, mercury must not be used any
longer in electronic equipment as of July 1st,
2006. For the sake of the environment WIMA
has refraind from using such substances since
years already.
WIMA capacitors are lead free
in accordance with Ro
HS 2011/65/EU
WIMA Kondensatoren sind bleifrei
konform RoHS 2011/65/EU
Tape for lead-free WIMA capacitors
DIN EN ISO 14001:2004
WIMA’s environmental management has
been established in accordance with the
guidelines of DIN EN ISO 14001:2004 to
optimize the production processes with
regard to energy and resources.
Soldering Process
Internal temperature of the capacitor must
be kept as follows:
Polyester: preheating: Tmax. 125° C
soldering: Tmax. 135° C
Polypropylene: preheating: Tmax. 100° C
soldering: Tmax. 110° C
Single wave soldering
Soldering bath temperature: T 260 ° C
Dwell time: t 5 sec
Double wave soldering
Soldering bath temperature: T 260 ° C
Dwell time: St 5 sec
Due to different soldering processes and
heat requirements the graphs are to be
regarded as a recommendation only.
145
04.16
D
P
P1
P0
P2
F
d
P
P1
H1
H
P0
d
P2
F
t
D0
W2
Vh
W0
P1
P2
P0
P
H1
H
W
1
W
d
F
Diagram 1:
PCM2.5/5/7.5mm
Diagram3:PCM 22.5and 27.5*mm
*PCM 27.5taping possiblewithtwo feed holesbetween components
Di
agram 2: PCM10/15mm
Dimensions for Radial Taping
Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping
Carrier tape width W 18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
Hold-down tape width W
0
6.0 for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing
adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape
Hole position W
1
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
Hold-down tape position W
2
0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max.
Feed hole diameter D
0
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
Pitch of component P 12.7
p1.0
12.7
p1.0
12.7
p1.0
25.4
p1.0
25.4
p1.0
38.1
p1.5
3
*8.1
p1.5
or 50.8
p1.5
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
Feed hole pitch P
0
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
Feed hole centre P
1
5.1
p0.5
3.85
p0.7
2.6
p0.7
7.7
p0.7
5.2
p0.7
7.8
p0.7
5.3
p0.7
to pin
Hole centre to P
2
6.35
p1.3
6.35
p1.3
6.35
p1.3
12.7
p1.3
12.7
p1.3
19.05
p1.3
19.05
p1.3
component centre
Feed hole centre to bottom H 16.5
p0.3
16.5
p0.3
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
edge of the component 18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
Feed hole centre to top H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
edge of the component 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0
Pin spacing at F 2.5
p0.5
5.0
+0.8
7.5
p0.8
10.0
p0.8
15
p0.8
22.5
p0.8
27.5
p0.8
upper edge of carrier tape
–0.2
Pin diameter d 0.4
p0.05
0.5
p0.05
0.5
p0.05
or
0.6
–0.05
0.5
p0.05
or
0.6
–0.05
0.8
–0.05
0.8
–0.05
0.8
–0.05
Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max.
Total tape thickness t 0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
ROLL/AMMO AMMO
Package
(see also page 146)
Unit see details page 147.
Dims in mm.
Diameter of pins see General Data. Please clarify customer-specific deviations with the manufacturer.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P0 = 12.7 or 15.0 is possible
REEL
P 360 max.
B
52 p2 depending on
P 30 p1 58 p2 comp. dimensions
52 p2 54 p2 depending
REEL
P 360 max. B 58 p2
or
REEL
P 500 max. B 60 p2 on PCM and
P 30 p1 66 p2 P 25 p1 68 p2 component dimensions
+0.06 +0,06 +0,08 +0,08 +0.08
Typical Dimensions for
Taping Configuration
146
04.16
D
˜ ROLL Packaging ˜ AMMO Packaging ˜ REEL Packaging
Labelling of package units in
plain text and with
alphanumerical Bar Code
Scanner decoding of
WIMA supplier number
Customer‘s P/O number
Customer‘s part number
WIMA confirmation number
WIMA part number
Lot number
Date code
Quantity
In addition part description of
– article
– capacitance value
– rated voltage
– dimensions
– capacitance tolerance
– packing
as well as gross weight and customer‘s
name are indicated in plain text.
BARCODE „Code 39”
BAR CODE (Labelling)
50 max.
70 max.
340 max.
490 max.
340 max.
370 max.
30 1±
25 1±
360 max.
500 max.
B
340 max.
340 max.
50 max.
Types of Tape Packaging of
Capacitors for Automatic
Radial Insertion
147
04.16
D
Packing Quantities for Capacitors with
Radial Pins in PCM 2.5 mm to 22.5 mm
* TPS (Tray-Packing-System). Plate versions may have different packing units. Moulded versions. Rights reserved to amend design data without prior notification.
Samples and pre-production needs on request.
PCM Size
pcs. per packing unit
bulk
ROLL REEL AMMO
P 360 P 500 340 x 340 490 x 370
H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5
W H L Codes S N O F I H J A C B D
2.5 mm
2.5 7 4.6 0B 5000 2200 2500 2800
3 7.5 4.6 0C 5000 2000 2300 2300
3.8 8.5 4.6 0D 5000 1500 1800 1800
4.6 9 4.6 0E 5000 1200 1500 1500
5.5 10 4.6 0F 5000 900 1200 1200
5 mm
2.5 6.5 7.2 1A 5000 2200 2500 2800
3 7.5 7.2 1B 5000 2000 2300 2300
3.5 8.5 7.2 1C 5000 1600 2000 2000
4.5 6 7.2 1D 6000 1300 1500 1500
4.5 9.5 7.2 1E 4000 1300 1500 1500
5 10 7.2 1F 3500 1100 1400 1400
5.5 7 7.2 1G 4000 1000 1200 1200
5.5 11.5 7.2 1H 2500 1000 1200 1200
6.5 8 7.2 1I 2500 800 1000 1000
7.2 8.5 7.2 1J 2500 700 1000 1000
7.2 13 7.2 1K 2000 700 950 1000
8.5 10 7.2 1L 2000 600 800 800
8.5 14 7.2 1M 1500 600 800 800
11 16 7.2 1N 1000 500 600 400
7.5 mm
2.5 7 10 2A 5000 2500 4400 2500
3 8.5 10 2B 5000 2200 4300 2300 4150
4 9 10 2C 4000 1700 3200 1700 3100
4.5 9.5 10.3 2D 3500 1500 2900 1400 2700
5 10.5 10.3 2E 3000 1300 2500 1300
5.7 12.5 10.3 2F 2000 1000 2200 1100
7.2 12.5 10.3 2G 1500 900 1800 1000
10 mm
3 9 13 3A 3000 1100 2200 1900
4 8.5 13.5 FA 3000 900 1600 1450
4 9 13 3C 3000 900 1600 1450
4 9.5 13 3D 3000 900 1600 1400
5 10 13.5 FB 2000 700 1300 1200
5 11 13 3F 3000 700 1300 1200
6 12 13 3G 2400 550 1100 1000
6 12.5 13 3H 2400 550 1100 1000
8 12 13 3I 2000 400 800 740
15 mm
5 11 18 4B 2400 600 1200 1150
5 13 19 FC 1000 600 1200 1200
6 12.5 18 4C 2000 500 1000 1000
6 14 19 FD 1000 500 1000 1000
7 14 18 4D 1600 450 900 850
7 15 19 FE 1000 450 900 850
8 15 18 4F 1200 400 800 740
8 17 19 FF 500 400 800 740
9 14 18 4H 1200 350 700 650
9 16 18 4J 900 350 700 650
10 18 19 FG 500 300 650 590
11 14 18 4M 1000 300 600 540
22.5 mm
5 14 26.5 5A 1200 800 770
6 15 26.5 5B 1000 700 640
7 16.5 26.5 5D 760 600 550
8 20 28 FH 500 500 480
8.5 18.5 26.5 5F 500 480 450
10 22 28 FI 570* 420 380
10.5 19 26.5 5G 594* 400 360
10.5 20.5 26.5 5H 594* 400 360
11 21 26.5 5I 561* 380 350
12 24 28 FJ 480* 350 310
148
04.16
D
* for 2-inch transport pitches. Moulded versions. Rights reserved to amend design data without prior notification.
* TPS (Tray-Packing-System). Plate versions may have different packing units.
Samples and pre-production needs on request.
Updated data on www.wima.com
Packing Quantities for Capacitors with
Radial Pins in PCM 27.5 mm to 52.5 mm
PCM Size
pcs. per packing unit
bulk
ROLL REEL AMMO
P 360 P 500 340 x 340 490 x 370
H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5
W H L Codes S N O F I H J A C B D
27.5 mm
9 19 31.5 6A 567* 460/340* 420
11 21 31.5 6B 459* 380/280* 350
13 24 31.5 6D 378* 300 290
13 25 33 FK 405*–––––
15 26 31.5 6F 324* 270 250
15 26 33 FL 324*–––––
17 29 31.5 6G 198*–––––
17 34.5 31.5 6I 198*–––––
20 32 33 FM 162*–––––
20 39.5 31.5 6J 162*–––––
37.5 mm
9 19 41.5 7A 441*–––––
11 22 41.5 7B 357*–––––
13 24 41.5 7C 294*–––––
15 26 41.5 7D 252*–––––
17 29 41.5 7E 154*–––––
19 32 41.5 7F 140*–––––
20 39.5 41.5 7G 126*–––––
24 45.5 41.5 7H 112*–––––
31 46 41.5 7I 84*–––––
35 50 41.5 7J 35*–––––
40 55 41.5 7K 28*–––––
48.5 mm
19 31 56 8D 120*–––––
23 34 56 8E 80*–––––
27 37.5 56 8H 84*–––––
33 48 56 8J 25*–––––
37 54 56 8L 25*–––––
52.5 mm
25 45 57 9D 70*–––––
30 45 57 9E 60*
35 50 57 9F 25*
45 55 57 9H 20*–––––
45 65 57 9J 20*–––––
143
04.16
D
A WIMA part number consists of 18 digits and is composed as follows:
Field 1 - 4: Type description
Field 5 - 6: Rated voltage
Field 7 - 10: Capacitance
Field 11 - 12: Size and PCM
Field 13 - 14: Version code (e.g. Snubber versions)
Field 15: Capacitance tolerance
Field 16: Packing
Field 17 - 18: Pin length (untaped)
12345678910 11 12 13 14 15 16 17 18
M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D
MKS 2 63 VDC 0.01 mF2.5 x 6.5 x 7.2 -20 %bulk 6 -2
WIMA Part Number System
The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the
pages of the respective WIMA range.
Type description: Rated voltage: Capacitance: Size: Tolerance:
SMD-PET = SMDT 50 VDC = B0 22 pF = 0022 4.8 x 3.3 x 3 Size 1812 = KA ±20 % = M
SMD-PEN = SMDN 63 VDC = C0 47 pF = 0047 4.8 x 3.3 x 4 Size 1812 = KB ±10 % = K
SMD-PPS = SMDI 100 VDC = D0 100 pF = 0100 5.7 x 5.1 x 3.5 Size 2220 = QA ±5 % = J
FKP 02 = FKP0 250 VDC = F0 150 pF = 0150 5.7 x 5.1 x 4.5 Size 2220 = QB ±2.5 % = H
MKS 02 = MKS0 400 VDC = G0 220 pF = 0220 7.2 x 6.1 x 3 Size 2824 = TA ±1 % = E
FKS 2 = FKS2 450 VDC = H0 330 pF = 0330 7.2 x 6.1 x 5 Size 2824 = TB ...
FKP 2 = FKP2 520 VDC = H2 470 pF = 0470 10.2 x 7.6 x 5 Size 4030 = VA
FKS 3 = FKS3 600 VDC = I0 680 pF = 0680 12.7 x 10.2 x 6 Size 5040 = XA
FKP 3 = FKP 3 630 VDC = J0 1000 pF = 1100 15.3 x 13.7 x 7 Size 6054 = YA Packing:
MKS 2 = MKS2 700 VDC = K0 1500 pF = 1150 2.5 x 7 x 4.6 PCM 2.5 = 0B AMMO H16.5 340 x 340 = A
MKP 2 = MKP2 800 VDC = L0 2200 pF = 1220 3 x 7.5 x 4.6 PCM 2.5 = 0C AMMO H16.5 490 x 370 = B
MKS 4 = MKS4 850 VDC = M0 3300 pF = 1330 2.5 x 6.5 x 7.2 PCM 5 = 1A AMMO H18.5 340 x 340 = C
MKP 4C = MKPC 900 VDC = N0 4700 pF = 1470 3 x 7.5 x 7.2 PCM 5 = 1B AMMO H18.5 490 x 370 = D
MKP 4 = MKP4 1000 VDC = O1 6800 pF = 1680 2.5 x 7 x 10 PCM 7.5 = 2A REEL H16.5 360 = F
MKP 10 = MKP1 1100 VDC = P0 0.01 mF= 2100 3 x 8.5 x 10 PCM 7.5 = 2B REEL H16.5 500 = H
FKP 1 = FKP1 1200 VDC = Q0 0.022 mF= 2220 3 x 9 x 13 PCM 10 = 3A REEL H18.5 360 = I
MKP-X2 = MKX2 1250 VDC = R0 0.047 mF= 2470 4 x 9 x 13 PCM 10 = 3C REEL H18.5 500 = J
MKP-X1 R = MKX1 1500 VDC = S0 0.1 mF= 3100 5 x 11 x 18 PCM 15 = 4B ROLL H16.5 = N
MKP-Y2 = MKY2 1600 VDC = T0 0.22 mF= 3220 6 x 12.5 x 18 PCM 15 = 4C ROLL H18.5 = O
MP 3-X2 = MPX2 2000 VDC = U0 0.47 mF= 3470 5 x 14 x 26.5 PCM 22.5 = 5A BLISTER W12 180 = P
MP 3-X1 = MPX1 2500 VDC = V0 1 mF= 4100 6 x 15 x 26.5 PCM 22.5 = 5B BLISTER W12 330 = Q
MP 3-Y2 = MPY2 3000 VDC = W0 2.2 mF= 4220 9 x 19 x 31.5 PCM 27.5 = 6A BLISTER W16 330 = R
MP 3R-Y2 = MPRY 4000 VDC = X0 4.7 mF= 4470 11 x21 x 31.5 PCM 27.5 = 6B BLISTER W24 330 = T
MKP 4F = MKPF 6000 VDC = Y0 10 mF= 5100 9 x 19 x 41.5 PCM 37.5 = 7A Bulk/TPS Standard = S
Snubber MKP = SNMP 250 VAC = 0W 22 mF= 5220 11 x 22 x 41.5 PCM 37.5 = 7B ...
Snubber FKP = SNFP 275 VAC = 1W 47 mF= 5470 19 x 31 x 56 PCM 48.5 = 8D
GTO MKP = GTOM 300 VAC = 2W 100 mF= 6100 25 x 45 x 57 PCM 52.5 = 9D
DC-LINK MKP 3 = DCP3 305 VAC = AW 220 mF= 6220 ...
DC-LINK MKP 4 = DCP4 350 VAC = BW 1000 mF= 7100
DC-LINK MKP 4S = DCPS 440 VAC = 4W 1500 mF= 7150
DC-LINK MKP 5 = DCP5 500 VAC = 5W ... Version code: Pin length (untaped)
DC-LINK MKP 6 = DCP6 ... Standard = 00 3.5 ±0.5 = C9
DC-LINK HC = DCHC Version A1 = 1A 6 -2 = SD
DC-LINK HY = DCHY Version A1.1.1 = 1B 16 ±1 = P1
Version A2 = 2A ...
... Pin length (taped)
none = 00