IN A
IN B
IN C
IN D
IN E
IN F
IN G
GND
OUT A
OUT B
OUT C
OUT D
OUT E
OUT F
OUT G
COMMON
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
A
B
C
D
E
F
G
DS2003
www.ti.com
SNLS394J –JANUARY 2000–REVISED APRIL 2013
DS2003 High Current/Voltage Darlington Drivers
Check for Samples: DS2003
1FEATURES DESCRIPTION
The DS2003 comprises seven high voltage, high
2• Seven High Gain Darlington Pairs current NPN Darlington transistor pairs. All units
• High Output Voltage (VCE = 50V) feature a common emitter and open collector outputs.
• High Output Current (IC= 350 mA) To maximize their effectiveness, these units contain
suppression diodes for inductive loads and
• TTL, PMOS, CMOS Compatible appropriate emitter base resistors for leakage.
• Suppression Diodes for Inductive Loads The DS2003 has a series base resistor to each
• Extended Temperature Range Darlington pair, thus allowing operation directly with
TTL or CMOS operating at supply voltages of 5.0V.
The DS2003 offers solutions to a great many
interface needs, including solenoids, relays, lamps,
small motors, and LEDs. Applications requiring sink
currents beyond the capability of a single output may
be accommodated by paralleling the outputs.
Connection Diagram
Top View
Figure 1.
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2000–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
DS2003
SNLS394J –JANUARY 2000–REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Storage Temperature Range −65°C to +150°C
Operating Temperature Range, TA
DS2003T −40°C to +125°C
DS2003C −40°C to +85°C
Junction Temperature Range, TJ−40°C to +150°C
Lead Temperature
Soldering, 10 seconds 265°C
ESD Ratings
Human Body Model +/-2000V
Machine Model +/- 200V
Package Thermal Dissipation Ratings
NFG0016E Package θJ-A 88°C/W
D0016A Package θJ-A 115°C/W
Input Voltage −0.3V to 30V
Output Voltage 55V
Emitter-Base Voltage 6.0V
Continuous Collector Current 500 mA
Continuous Base Current 25 mA
(1) “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be specified. They are not meant to imply
that the devices should be operated at these limits. The Electrical Characteristics provide conditions for actual device operation.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
Electrical Characteristics
TA= 25°C, unless otherwise specified (1)
Parameter Test Conditions Min Typ Max Units
ICEX Output Leakage TA= 25°C, VCE = 50V (Figure 6) 20 μA
Current TA= 85°C, VCE = 50V (Figure 6) 100
TA= 125°C, VCE = 50V (Figure 6) for DS2003T 150
VCE(Sat) Collector-Emitter IC= 350mA, IB= 500μA (Figure 8)(2) 1.25 1.6 V
Saturation Voltage IC= 200mA, IB= 350μA (Figure 8) 1.1 1.3
IC= 100mA, IB= 250μA (Figure 8) 0.9 1.1
II(ON) Input Current VI= 3.85V (Figure 9) 0.93 1.35 mA
II(OFF) Input Current IC= 500µA (Figure 10) 50 100 μA
(3) TA= +25°C 50 100
TA= +85°C 25 50
TA= +125C for DS2003T 10 25
VI(ON) Input Voltage VCE = 2.0V, IC= 200mA (Figure 11) 2.4 V
(4) VCE = 2.0V, IC= 250mA (Figure 11) 2.7
VCE = 2.0V, IC= 300mA (Figure 11) 3.0
CIInput Capacitance 15 30 pF
tPLH Turn-On Delay 0.5 VIto 0.5 VO1.0 μs
tPHL Turn-Off Delay 0.5 VIto 0.5 VO1.0 μs
(1) All limits apply to the complete Darlington series except as specified for a single device type.
(2) Under normal operating conditions these units will sustain 350 mA per output with VCE (Sat) = 1.6V at 70°C with a pulse width of 20 ms
and a duty cycle of 30%.
(3) The II(OFF) current limit ensured against partial turn-on of the output.
(4) The VI(ON) voltage limit ensures a minimum output sink current per the specified test conditions.
2Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: DS2003
DS2003
www.ti.com
SNLS394J –JANUARY 2000–REVISED APRIL 2013
Electrical Characteristics (continued)
TA= 25°C, unless otherwise specified (1)
Parameter Test Conditions Min Typ Max Units
IRClamp Diode VR= 50V (Figure 12) µA
Leakage Current TA= 25°C 5 10
TA= 85°C 10 50
TA= 125°C for DS2003T 20 100
VFClamp Diode IF= 350mA (Figure 13) 1.7 2.0 V
Forward Voltage
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS2003
DS2003
SNLS394J –JANUARY 2000–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
Collector Current vs Collector Current vs
Saturation Voltage Input Current
Figure 2. Figure 3.
Peak Collector Current vs
Input Current vs Duty Cycle and Number of
Input Voltage Outputs (N16E Package)
Figure 4. Figure 5.
4Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: DS2003
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
V+
VDD
GND
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
Input G
Input F
Input E
Input D
Input C
Input B
Input A
LED Test
V+
DS2003
SNLS394J –JANUARY 2000–REVISED APRIL 2013
www.ti.com
Typical Applications
Figure 14. Typical LED Driver
Figure 15. Typical Relay Driver
6Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: DS2003
DS2003
www.ti.com
SNLS394J –JANUARY 2000–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision I (April 2013) to Revision J Page
• Changed layout of National Data Sheet to TI format ............................................................................................................ 6
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: DS2003
PACKAGE OPTION ADDENDUM
www.ti.com 17-Aug-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
DS2003CM LIFEBUY SOIC D 16 48 TBD Call TI Call TI -40 to 85 DS2003CM
DS2003CM/NOPB LIFEBUY SOIC D 16 48 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 DS2003CM
DS2003CMX/NOPB LIFEBUY SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 DS2003CM
DS2003TM LIFEBUY SOIC D 16 48 TBD Call TI Call TI -40 to 125 DS2003TM
DS2003TM/NOPB LIFEBUY SOIC D 16 48 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 DS2003TM
DS2003TMX LIFEBUY SOIC D 16 2500 TBD Call TI Call TI -40 to 125 DS2003TM
DS2003TMX/NOPB LIFEBUY SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 DS2003TM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Aug-2017
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
