Product Specification G1225x01 series Crystal Clear Technology sdn. bhd. 16Jalan TP5--Taman Perindustrian Sime UEP 47600 Subang Jaya--Selangor DE Malaysia. T: +603 80247099 F: +603 80247098 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 1.0 Table of Contents Page 1. Table of Contents 1 2. Record of revision 2 3. General specification 3 4. Absolute maximum ratings 4 5. Electrical characteristics 4 6. Environmental requirement 4 7. LCD specification 5~7 8. Interface 8 9. Functional Description 9 ~ 13 10. Instructions 14 ~ 15 11. Power supply 16 12. Quality assurance 17 ~ 24 13. Precautions in use LCM 25 ~ 26 14. Outline drawing 27 15. LCD Segment and Common Layout 28 1 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 2.0 Record of revision Rev Date 1.0 30/09/08 2.0 31/10/08 Item 5.0 Page 4 Comment Originator Checked By Initial Release Syam Azhar Vdd values update 3.0V typ and Syam Azhar 3.3V max. 9.2.4 13 Figure error. Corrected from IF1, IF2, IF3 tie to high (Vdd), changed to all tie to low (Vss). 2 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 3.0 General specification Display format: Graphics 255 (w) x 128 (h) dots Dot size: 0.30 (w) x 0.30 (h) mm Dot pitch: 0.32 (w) x 0.32 (h) mm View area: 86.0 (w) x 44.0 (h) mm Active area: 81.58 (w) x 40.94 (h) mm General dimensions: 110.7 (w) x 63.2 (h) x 6.1 (t) mm Controller/Driver: ST7529 or equivalent Interface: Parallel/Serial Driving method: 1/144 duty, 1/11 bias G 1 2 2 5 0 1 0 0 MODEL NUMBER STD. GRAPHIC : No. of rows followed by no. of column SERIES NUMBER FOR THIS STANDARD SPECIFICATION BACKLIGHT MODE W : Side Led Backlight (White) N : No Backlight MODULE VERSION SERIES NUMBER FOR THIS STANDARD SPECIFICATION LCD MODE Y : Yellow Green (STN) G : Grey (STN) B : Black & White (FSTN) N : Negative (FSTN) Blue ( Single Retardation ) U : Negative (FSTN) Black/White ( Double Retardation ) S : Negative (STN) Purple L : Negative (STN) Blue Z : U : Negative (FSTN) Black/White ( Double Retardation ) TRI-AXIS VIEWING ANGLE T : Top view ( 12 O'clock ) B : Bottom view ( 6 O'clock ) OPERATING TEMPERATURE N : Normal Temperature ( 0C to +50C ), where storage temperature is (-20C to +70C) W : Wide Temperature ( -20C to +70C ), where storage temperature is (-30C to +80C) SEMI - CUSTOMISE (MINOR CHANGES FROM STANDARD MODEL) 00 - STANDARD SPECIFICATION MODEL T0 - WITH TOUCH PANEL REFER TO FACTORY FOR OTHER VERSIONS. TERMS AND CONDITIONS APPLY 3 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 4.0 NO 1. 2. 3. 5.0 NO 1. 2. 3. 5.1 Absolute maximum rating (at Vss = 0V, ambient temperature = 25C) ITEM Operating Voltage Range SIMBOL MIN MAX -0.5 5.0 -0.5 5.0 Refer page 3 Refer page 3 VDD VDDA Top Tst Operating Temperature Storage Temperature UNIT V C C Electrical characteristics ITEM Operating Voltage SYMBOL CONDITION MIN TYP MAX UNIT - - 3.0 3.3 V VDD VDDA Power Supply voltage (VLCD) Current Supply 16.05% 25C IDD VDD = 3.3V - 3.2 V - mA Backlight Options NO COLOR 1. White FORWARD VOLTAGE (V) Min Typ. Max 4.0 - FORWARD CURRENT (mA) Min Typ. Max 75 100 MIN BRIGHTNESS (cd/m2) * 250 *Note : 1. Brightness measured at backlight surface. 2. On LCD surface, brightness is only about 10% to 15% of backlight brightness. 3. Lifetime of backlight: For YG, Amber, Red = 50K hrs. For White, Blue = 20K hrs 6.0 NO Environmental requirements 2. 3. 4. ITEM Operating Temperature Storage Temperature Operating Humidity Cycle Test 5. Lifetime 1. CONDITION Refer page 3 Refer page 3 5% to 95%RH 0 C @ 30 min to 50 C @ 30min for 1 cycle run for 10 cycles 50000 HOURS (excluding backlight) Note: The background on LCD has the possibility to be changed in different temperature range. 4 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 7.0 LCD specification 7.1 Electro-optical characteristics (at ambient temperature = 25C) LCD TYPE UNIT STN -VE BLUE/ PURP LE FSTN +VE B/W FSTN -VE BLUE FSTN VE TRUE B/W FSTN -VE TRI AXIS NO ITEM SYMBOL CONDITION 1 Operating Voltage (Volt) VLCD =0 Cr = max 2 Viewing Angle (Deg) x 1 x 2 y 1 y 2 CR 2 VLCD = 14.7V +20 -20 -25 +25 +15 -15 -20 +20 +35 -35 -30 +30 +20 -20 -25 +25 +35 -35 -30 +30 +30 -35 -30 +30 +40 -40 -50 +30 7.1.2 3 Contrast Ratio CR = 00 VLCD =14.7V 2.5 2.0 5.5 2.5 5.5 15 15 7.1.3 Response Time (msec) Rise Time (Tr) Decay Time (Td) 4 = 00 STN YG STN GREY 16.0 5% REF. 7.1.1 400 7.1.4 = 00 400 Note: 1. Viewing angle data is based on bottom view product by default. Should it be a top view product, values are then swap. 2. Contrast ratio is based on typical data when using white colour as backlight. 3. Equipment Used Eldim; Ez Contrast 120R , Spot Size = 2mm 5 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 NO CHARACTERISTICS 7.1.1 Definition of Operating Voltage (VLCD) DEFINITIONS VLCD 1/F VLCD : Operating Voltage F : Frame Frequency 7.1.2 TOP Definition of Viewing Angle REAR LEFT RIGHT FRONT BOTTOM REAR (y2) LEFT(x2) RIGHT(x1) FRONT (y1) 6 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 7.1.3 Definition of Contrast Ratio NON-SELECT WAVE BRIGHTNESS (%) SELECT WAVE b a OPERATION VOLTAGE Contrast Ratio = Brightness of non-selected state (b) Brightness of selected state (a) Conditions (a) Operating Voltage: VLCD (b) Temperature: 25C (c) Viewing Angle, = 0o 7.1.4 Response Time Luminance (%) 90 10 Td Tr Time Tr: Measured between 10% and 90% of LCD segment maximum response with VON. Td: With voltage switches to zero and the instant LCD segment reaches 10% of its maximum response. 7 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 8.0 Interface ST7529 OR EQUIVALENT 8.1 Display Driver 8.2 Pin No Symbol Description 1 V0 LCD driving voltage 2 V1 LCD driving voltage 3 V2 LCD driving voltage 4 V3 LCD driving voltage 5 V4 LCD driving voltage 6 VLCD LCD driving voltage 7 C6P Positive connection for capacitor 6 8 C4P Positive connection for capacitor 4 9 C2N Negative connection for capacitor 2 10 C2P Positive connection for capacitor 2 11 C1P Positive connection for capacitor 1 12 C1N Negative connection for capacitor 1 13 C3P Positive connection for capacitor 3 14 C5P Positive connection for capacitor 5 15 VDDA Internal generator supply 16 VSS Ground 17 VSS Ground 18 VDD Logic supply voltage 19 XCS Chip select input pin 20 SCL Serial clock input pin 21 SI Serial data input pin 22 IF3 Interface mode selection 23 IF2 Interface mode selection 24 IF1 Interface mode selection 25 RST Reset input active low 26 ERD 27 D7 R/W : 68000 Series Parallel Interface Read & Write Control Input RD : 8080 Series Parallel Interface Read Enable Clock Input 8 bit bi-directional data bus 28 D6 8 bit bi-directional data bus 29 D5 8 bit bi-directional data bus 30 D4 8 bit bi-directional data bus 31 D3 8 bit bi-directional data bus 32 D2 8 bit bi-directional data bus 33 D1 8 bit bi-directional data bus 34 D0 8 bit bi-directional data bus 35 EWR 36 A0 R/W : 68000 Series Parallel Interface Read & Write Control Input RD : 8080 Series Parallel Interface Write Enable Clock Input Register select input pin 8 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 9.0 Functional Descriptions 9.1 Read/Write timing characteristics Read/Write characteristics (6800 series MPU) 9 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Read/Write characteristics (8080 series MPU) 10 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Read/Write characteristics (Serial Interface 4 Line) 11 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Read/Write characteristics (Serial Interface 3 Line) 9.2 Application Circuits 9.2.1 6800 - Series Parallel Interface A0 EWR ERD D0~D7 MCU A0 EWR D0~D7 VDD IF2 IF3 VSS IF1 VDD LCD Module 12 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 9.2.2 8080 - Series Parallel Interface A0 EWR ERD D0~D7 A0 EWR ERD D0~D7 VDD IF1 IF2 VSS IF3 MCU VDD LCD Module 9.2.3 3 Lines Serial Interface RST SI SCL XCS RST SI SCL XCS VSS VDD MCU 9.2.4 VDD IF3 LCD Module 4 Lines Serial Interface RST SI SCL XCS A0 VSS MCU IF1 IF2 RST SI SCL XCS A0 IF1 IF2 IF3 LCD Module 13 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 10. Instruction set 14 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 15 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 11. Power Supply 11.1 6x Boosting 11.2 7x Boosting Cap = 1.0 uF to 2.2 uF +4.0V 0V A K B ACKLIGHT SUPPLY 16 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 12.0 Quality Assurance 12.1 ZONE DEFINITION ZONE A EFFECTIVE VIEWING AREA ZONE B (Outside Viewing Area) ZONE C (Sealing Area) 12.2 REJECTION CRITERIA 12.2.1 DIMENSIONAL DEFECTS Defect Category Glass Size Perimeter Seal Extension End Seal Size Defect Description Dimensions of LCD, do not conform to the drawing Perimeter seal epoxy enters the effective viewing area Size of end seal does not meet drawing specification Criterion Reject Drawing Specification Refer to LCD Physical Dimension Drawing Reject Reject Refer to LCD Physical Dimension Drawing 12.2.2 VISUAL DEFECTS Defect Category Fracture Defect Description A type of glass breakage containing running cracks. Inspectors should attempt to remove it with fingernail. If removed, evaluate as chip Criterion Drawing Specification Reject - if the size is > 30% of the contact ledge width. 17 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Defect Category Chip Defect Description Chip in cross over area Criterion Drawing Specification 1) Reject - if the chip causes crossover dot to be exposed Chip Epoxy of crossover dot exposed 2) Chip on outside edge of the glass plate but is greater than 50% of glass thickness at crossover dot is reject able. Chip Chip in contact pad area Accept if:a) X 2.0mm b) Y 0.5mm c) Z disregard Y Z X Chip in noncontact pad area Accept if:a) X 6.0mm b) Y 1.0mm c) Z disregard Y Z X X Y Chip in perimeter seal area Corner Chip Corner chip within seal area Accept if:a) Y 1/3 of perimeter seal width (W) b) X 3.0mm c) Z disregard d) X and Y not touch crossover dot Accept if:a) X 1/3 of perimeter seal width (W) b) Y 1/3 of perimeter seal width (W) c) Z disregard W Y Z X Y Z X W X Y Z 18 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Defect Category Defect Description Corner chip not effecting contact pad / ITO Criterion Drawing Specification Accept if:a) XY 4mm2 AND b) Y D and X 2.0mm c) Z disregard D X Y Z Corner chip effecting contact pad / ITO A) Accept if:a) XY 4mm2 AND b) Y D and X 2.0mm D X1 Y1 Y X B) Accept if:a) X1 2.0mm b) Y1 0.5mm Z B A Z disregard Glass flare A thin layer of glass flare at contact area Accept if:a) Flare thickness 1/4 W when W 3mm b) Flare thickness 1mm when W > 3mm W: Contact ledge width Glass burr Rainbow A rough edge(s) left along the scribing edge (i.e. along the edges of display) Colored ring in sharp blotches observed Reject - if the burr cause undersize or oversize of the LCD Refer to LCD Physical Dimension Drawing Reject - if 3 or more colored rings in sharp blotches of color are observed. (Limit samples should be used when applicable) 19 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Defect Category Discoloration Air Void Fill end contamination 12.2.3 Defect Description LC does not fulfill the display Discoloration at end seal area Criterion Drawing Specification Reject - if the discolorations enter the active viewing area of LCD. Color of the LCD shall follow product specification as specified in the manufacturing specification Reject Reject if discoloration exceeded the baffle (for display with baffle) or viewing area (for display without baffle) POLARIZER DEFECTS Defect Category Polarizer defect Defect Description Criterion Polarizer coverage 1- Polarizer should cover effective viewing area of display. 2- It is acceptable if perimeter seal bolder at all sides could be seen. 3- It is acceptable if polarizer attaching position meeting the tolerance mentioned in the drawing. 4- It is reject able if polarizer edge jagged and not even Polarizer Peeling / delamination 1- Reject if any edge or corner of the polarizer is lifted up or not adheres to the glass Polarizer Scratches 1- Any scratch should be acceptable if it is not visible from viewing distance at head of position 2-Polarizer scratch in viewing area is reject able if it is visible from the specified viewing distance 3-Defect, which is visible under surface glare, should be disregard Drawing Specification Refer to LCD Physical Dimension Drawing 20 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Defect Category Defect Description Polarizer damage Polarizer bubble / Foreign material Criterion Drawing Specification 1-Stain mark or depression in front polarizer surface should be acceptable if it is not visible from viewing distance at head on position. 2-Defect, which is visible under surface glare, should be disregard Zone / Dimension D 0.30mm D 0.50mm 0.50 < D 0.60mm D > 0.60mm Acceptable No. A B C NC if NC NC the 2 NC Polarize 1 2 r not lifted up/ peel 0 0 off B A D = (A + B)/2 NC: No count D: Mean Diameter of Defect 3 are the totally permissible numbers of bubble 12.2.4 ELECTRICAL TEST DEFECTS Defect Category Missing common Missing segment Commoncommon short Segmentsegment short Common - segment short Wrong viewing angle Metal residue Slow response Defect Description Criterion Drawing Specification Part of the pattern Reject does not light up One or few Reject segment does not light up Common and Reject common connected Segment and Reject segment connected Common and Reject segment connected Wrong viewing Reject if display viewing angle not angle conform to customer requirement Extra spot lights up Accept if 0.20mm (mean diameter) at the border of the segment. Reject if it is visible at 30cm distance Response of the display on one side slower than the other side 21 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 Defect Category Pin Hole Deformed display dot Defect Description Pin hole / void at light up segment Lacked deformation Criterion Drawing Specification Y Zone / Acceptable No. Dimension Located inside - 1 per pixel/dot single pixel/dot:- 3 per display (X + Y)/2 (Active Area) 0.20mm Laid over the plural - 1 per pixel/dot pixel/dots: - 3 per display (X + Y)/2 (Active Area) 0.20mm (3/4 or larger part of dot area has to be effective for display) X X Accept if: i) X 0.15 and ii) Y 0.15 Y Added deformation Accept if: i) X < 0.02 and ii) Y < 0.02 X Y Reverse twist/ tilt Misalignment Segment Smearing Dim segment Segment are darker or clearer than other area of the same segment Segment fatter or smaller or extra segment Light up segment smear Display shows poor contrast at pre set voltage Reject Reject if > 10% of designed segment width and visible at 30cm distance Reject Reject 22 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 12.2.5 BLACK SPOT, WHITE SPOT AND FOREIGN MATERIAL (SOLID FIGURE) Defect Category Black Spot, White Spot and Foreign Material Defect Description Black Spot, White Spot and Foreign Material Criterion Zone / Dimension Drawing Specification Acceptable No. A B C NC NC NC 0.10<D < 0.15mm 3 3 NC 0.15 < D < 0.25mm 1 2 NC 0.25 < D < 0.35mm 1 1 NC D > 0.35 mm NC: No count 0 0 NC D < 0.10mm B A D = (A + B)/2 D: Mean Diameter of Defect NOTE: The 1/3 or larger parts of individual dot has to be lighted on. The solid figure is that the defect has clear-cut outline at the optimum driving condition in both positive and negative, of which size does not change when the contrast changes. 12.2.6 BLACK SPOT, WHITE SPOT AND FOREIGN MATERIAL (FADED FIGURE) Defect Category Black Spot, White Spot and Foreign Material Defect Description Black Spot, White Spot and Foreign Material Criterion Zone / Dimension D < 0.60mm Drawing Specification Acceptable No. A B C NC NC NC 0.60<D < 0.70mm 3 NC 0.70 < D < 0.80mm 1 NC D > 0.80 mm NC: No count 0 NC B A D = (A + B)/2 D: Mean Diameter of Defect NOTE: Faded figure means that the defects has unclear outline at the optimum driving condition in both positive and negative, of which size seems to change when the contrast changes. 23 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 12.2.7 LINE SHAPE AND SCRATCHES Defect Category Line shape and scratches Defect Description Line shape and scratches Criterion Zone /Dimension X Y NC 0.03mm 2 mm 0.05mm 1 mm 0.10mm NC 0.10mm Drawing Specification Acceptable No. A B C NC NC NC 1 1 NC 1 2 NC Due to (1) round defect NOTE: Length is X and Width is Y. REMARK: i) Total amount of spot defects including round and linear - A total of 5 permissible numbers of defects in Zone A & B including above (12.2.5), (12.2.6), (12.2.7). Regardless of number of defects, the minimum distance between individual defects have to be 5mm or larger. ii) All the other items of inspection that are not included herein must be determined by the "Limit Standard" sample, which were occasionally set up with the mutual consent of both parties. In every case of the items set up with the Limit Standard, the Limit Standard always takes precedence over the other means of definition. 24 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 13. Precaution for using LCM 1. Liquid Crystal Display (LCD) a) LCD is made up of glass, organic sealant, organic fluid and Avoid pressing on the metal bezel, polymer based polarizers. The following precautions should otherwise be taken when handling. could be deformed and lose contact, b) the elastomer connector resulting in missing pixels. Keep the temperature within the range of use and storage. Excessive temperature and humidity c) d) could cause polarization degredation, polarizer 2.2 Static Electricity peel off or bubble. LCM contains CMOS LSI's and the same Do not contact the exposed polarizer with precaution for such devices should apply, namely anything harder than HB pencil lead. To clean a) dust off the display surface, wipe gently with he/she comes into contact with the module. cotton, chamois or other soft material soaked in Never touch any of the conductive parts petroleum benzin. such as the LSI pads, the copper leads on the Wipe off saliva or water drops immediately. PCB and the interface terminals with any Contact with water over a long period of time parts of the human body. may cause polarizer deformation or colour b) condensation on its surface will cause corrosion c) Only properly grounded soldering irons should be used. of ITO electrodes. f) The modules should be kept in antistatic bags or other containers to static for storage. fading, while an active LCD with water e) The operator should be grounded whenever Glass can be easily chipped or cracked from d) If an electric screwdriver is used, it should rough handling, especially at corners and edges. be well grounded and shielded from Do not drive LCD with DC voltage. commutator spark. e) The normal static prevention measures should be observed for work clothes and 2. Liquid Crystal Display Modules. working benches, the latter conductive 2.1 Mechanical Considerations (rubber) mat is recommended. LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and f) Since dry air is inductive to statics, a relative humidity of 50-60% is recommended. do not make any alterations or modification. The following should be noted. a) b) Do not tamper in any way with the tabs 2.3 Soldering on the metal frame. a) Solder only to the I/O terminals. Do not modify the PCB by drilling b) Use only soldering irons with proper extra c) d) holes, changing its grounding and no leakage. outline, moving its component or modifying its c) Soldering temperature: 280 C pattern. d) Soldering time: 3 to 4 sec Do not touch the elastomer connector, e) Use eutectic solder with resin flux fill. especially insert a backlight panel (for f) If flux is used, the LCD surface should be example, EL) covered to avoid flux spatters. Flux residue When mounting a LCM make sure that should be removed afterwards. the PCB is not under any stress such as bending or twisting. Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. 25 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 2.4 Operation a) The contras can be adjusted by varying the LCD driving voltage V0 b) Driving voltage should be kept within specified range, excess voltage shortens display life. c) Response time increases with decrease in temperature. d) Display may turn black or dark blue at temperature above its operational range, this is (however not pressing on the viewing area) may cause the segments to appear "fractured". e) Mechanical disturbance during operation ( such as pressing on the viewing area) may cause the segments to appear "fractured". 2.5 Storage If any fluid leaks out of the damage glass cell, wash off any human part that comes into contact with soap and water. Never swallow the fluid. The toxicity is extremely low but caution should be exercised at all the time. 2.6 Limited Warranty Unless otherwise agreed between Crystal Clear Technology and customer, Crystal Clear Technology will replace or repair any of its LCD and LCM which is found to be defective electrically and visually when inspected in accordance with Crystal Clear Technology acceptance standards, for a period of one year from date of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of Crystal Clear Technology is limited to repair and/or replacement on the terms set forth above. Crystal Clear Technology will not responsible for any subsequent or consequential events. 26 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 01 36 Crystal-Clear Technology 16, JLN TP5, TMN PERINDUSTRIAN SIME UEP, 47500 SUBANG JAYA, SELANGOR DARUL EHSAN. 27 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G1225x01xxx00 REV 2.0 LCD Segment and Common Layout 28 Crystal Clear Technology 16 Jalan TP5--Taman Perindustrian Sime UEP 47600 Subang Jaya--Selangor DE Malaysia